LG | 900B-CB997E-EA | LG 900B(CB997E-EA) Owner’s Manual

Thank you for purchasing a high resolution monitor. It will give you high
resolution performance and convenient reliable operation in a variety of
video
operating modes.
Features
The monitor is
19 inches
(18.0
inches viewable
) intelligent, microprocessor
compatible
analog RGB (Red, Green, Blue) display
standards, including IBM PC , PS/2 , Apple , Macintosh , Centris , Quadra , and
Macintosh II family.
a
based monitor
with most
The monitor
provides crisp text and vivid color graphics with VGA, SVGA, XGA,
Ergonomic modes (non-interlaced), and most Macintosh compatible
color video cards when used with the appropriate adaptor. The monitor's wide
compatibility makes it possible to upgrade video cards or software without
purchasing a new monitor.
and VESA
Digitally controlled auto-scanning is done with the micro-processor for horizontal
frequencies between 30 and 96kHz, and vertical scan frequencies
scan
between 50-160Hz.
This monitor is
dots and
a
capable
of
producing
a
maximum horizontal resolution of 1600
maximum vertical resolution of 1200 lines.
The
microprocessor-based digital controls allow you to adjust conveniently
variety of image controls by using the OSD (On Screen Display).
USB
a
(Universal Serial Bus) ports at the back of the monitor are prepared for the
can easily and flexibly connect USB-designed devicessuch as a mouse, keyboard or printer- to the monitor for true Plug and Play
USB cable and hub. You
function.*
Plug
and
play capability
if
supported by your system
This monitor has DDC 1 and DDC 2B function.**
Compliant with
-
-
-
the
following regulated specifications
:**
EPA ENERGY STAR
Swedish MPR II
Swedish TCO'99
*
Applies
**
to 900B plus
only.
For detailed information,
please refer to
the Reference
provided
.
Connecting
the Monitor
Turn off the
equipment and all attached options.
Carefully set the monitor face-down with the underside facing you.
Installation
1.
Align
the hooks
on
the tilt/swivel stand with the
matching
slots in the base of
the monitor.
2. Insert the hooks into slots.
3. Slide the tilt/swivel stand toward the front of the monitor until the latches click
into the locked
position.
Slots
Hooks
Latch
A2
the Monitor
Connecting
On the back of the monitor
power
1
2
cord,
are
plug-in connections; one for the AC
signal cable from the video card.
two
and the other for the
Power off both the monitor and PC.
Connect the 15
pin VGA connector of
VGA video connector
on
the
supplied signal
cable to the output
only one way. If
the PC. The connectors will mate
you cannot attach the cable easily, turn the connector upside down and try
again. When mated, tighten the thumbscrews to secure the connection.
2'
appropriate MAC to VGA adapter block at your local computer
adapter changes the high density 3 row 15 pin VGA connector to
the correct 15 pin 2 row connection to mate with your MAC. Attach the other
end of the signal cable to the side of the adapter block with 3 rows.
Locate the
store. This
Connect the attached
cable to the video output
adapter block/signal
on
your
MAC.
3
One end of the AC power cord is connected into the AC power connector on
the back of the monitor. The other end is plugged into a properly grounded
three-prong AC outlet.
4
5
Power ON the PC, then the monitor.
If you
see
the SELF DIAGNOSTICS message, check the
signal
cable and
connectors.
6
After
using
the system, power OFF the monitor, then the PC.
IBM PC
MACINTOSH
2'
2
Mac
D-15P
3
Power Cord
Applies to
900B
Signal
Adapter
MAC6
D-15P
plus only.
Cable
*
NOTE
:
For
Apple
Macintosh use,
separate plug adapter is needed
change the
15
pin high density (3 row)
on the supplied
pin 2 row connector.
D-sub VGA connector
cable to
A3
a
15
a
to
Making
use
of USB
(Universal Serial Bus)- Applies to 900B plus only
Bus) is an innovation in connecting your different
desktop peripherals conveniently to your computer. By using the USB, you will
be able to connect your mouse, keyboard, printer, and other peripherals to your
USB (Universal Serial
monitor instead of having to connect them to your computer. This will give you
greater flexibility in setting up your system. USB allows you to connect chain up
to 120 devices
on a single USB port, and you can "hot" plug (attach them while
the computer is running) or unplug them while maintaining Plug and Plug auto
detection and configuration. This monitor has an integrated self-powered USB
hub, allowing up to 4 other USB devices to be attached it.
USB connection
1.
Connect the upstream port of the monitor to the downstream port of the USB
compliant PC or another hub using the USB cable (Computer must have a
2.
Connect the USB
USB
port).
compliant peripherals
to the downstream
ports of the
monitor.
USB downstream Ports
connect the cables from USB
compliant peripherals-such
keyboard, mouse, printer,
as
scanner, etc
USB
etc.
upstream Port
To USB downstream
mouseprinter
keyboard
the USB
compliant
port of
PC
or
another hub cable
NOTE
To activate the USB hub function, the monitor must be connected to
PC(OS) or another hub with the USB cable(enclosed).
When connecting the USB cable, check that the
side matches the shape at the connecting side.
shape
a
USB
compliant
of the connector at the cable
When the monitor is not plugged into an electric socket, the
the downstream ports will not operate.
peripherals
connected to
Even if the monitor is in a power saving mode, USB compliant devices will function
when they are connected the USB ports(both the upstream and downstream) of the
monitor.
A4
Location and Function of Controls
Front View
MENU
Power Button
SELECT
Power Indicator
SELECT Button
Buttons
MENU Button
Rear View
ID Label
USB upstream
port*
USB downstream
AC Power Socket
D-Sub
Signal
Cable
*
A5
Applies
to 900B
plus only.
ports*
Control Panel Function
Front Panel Controls
MENU Button
SELECT Button
MENU
Power
(DPMS) Indicator
SELECT
Power Button
Buttons
<Shortcut
?
100
100
Keys>
Brightness and Contrast can be adjusted directly without
entering the On Screen Display (OSD) system. Press the
buttons to display the menu and then the
buttons to adjust the settings. To save all changes, press
the MENU button. The Brightness and Contrast functions
are also available in the On Screen Display (OSD) menu.
Control
MENU
Function
MENU Button
Use this button to enter
or
exit the
on screen
display.
Buttons
Use these buttons to choose
the
SELECT
SELECT Button
on screen
Use this button to enter
screen
Power (DPMS)
Indicator
adjust
items in
a
selection in the
on
display.
This Indicator
lights
up green when the monitor
operates normally. If the monitor is in DPM
(Energy Saving)
mode
this indicator color
Power Button
or
display.
(stand-by/suspend/off),
changes to amber.
Use this button to turn the monitor
A6
on or
off.
On Screen
Display (OSD) Control Adjustment
Making adjustments to the image size, position and operating parameters of
the monitor are quick and easy with the On Screen Display Control system. A
quick example is given below to familiarize you with the use of the controls.
Following section is an outline of the available adjustments and selections you
can make using the OSD.
NOTE
Allow the monitor to stabilize for at least 30 minutes before
To make
adjustments
in the On Screen
Display,
making image adjustment.
follow these steps:
MENU
SELECT
SELECT
MENU
12
Press the MENU Button, then the main
To
acces a
becomes
3
Use the
45
Accept
control,
use
highlighted,
the
the
of the OSD appears.
Buttons. When the icon you want
press the SELECT Button.
Buttons to
changes by pressing
Exit the OSD
or
menu
by Pressing
adjust
the item to the desired level.
the SELECT Button.
the MENU Button.
A7
You
were
introduced to the
procedure of selection and adjusting an item
the OSD
using
descriptions
system. Listed below are the icons, icon names, and icon
of the items that are shown on the Menu.
BRIGHTNESS CONTRAST
66
Brightness
Used to adjust the brightness
of the
screen.
92
Contrast
Adjust the display to the
POSITION
contrast desired.
Vertical Position
To move image up and down.
66
45
SIZE
Horizontal Position
To move picture image left and
Vertical Size
To
49
64
adjust image height.
Horizontal Size
To
adjust image width.
right.
SHAPE
Tilt
To correct
image
rotation.
Side Pincushion
To correct the
bowing
in and out of the
image.
Side
pincushion
balance
To correct the balance of both sides
bowing.
Parallelogram
This control
screen
adjusts
image.
for
a
skewing
of the
Trapezoid
To correct
Top
geometric distortion.
Corner
To correct the
irregular distortion
displayed image.
of the
Bottom Corner
To correct the
irregular distortion
displayed image.
PRESET
COLOR
PRESET
6500K
6500K/ 9300K
To appear the
9300K
TEMP
?
?
RED
of the
displays
6500K:Slightly
9300K:Slightly
color
temperature.
reddish white.
bluish white.
GREEN
BLUE
TEMP
User
easily color set without adjustment
Red, Green and Blue (R/G/B).
RED
GREEN
BLUE
To set your
own
color levels.
On Screen
Display(OSD)
OSD
Selection and
Adjust
Adjustment
Description
VIDEO LEVEL This item is used to select the monitor's
SETUP
VIDEO LEVEL
0.7V
LANGUAGE
ENGLISH
input signal
level. The normal level used for
most PC's is 0.7V.
When the screen
OSD POSITION
suddenly gets brightened
blurry, please select 1.0V and try again.
or
LANGUAGE
To choose the
language in which the
displayed.
OSD Menus are available in 11 languages:
English, German, French, Spanish, Italian,
Swedish, Finnish, Portuguese, Korean,
control
names are
Chinese and Russian.
OSD POSITION To
adjust position of the OSD window on
the screen.
SPECIAL
DEGAUSS To
DEGAUSS
ON
RECALL
ON
MOIRE
H: 0/V: 0
CONVERGENCE
H:50
manually demagnetize the screen which
image or color incorrectly.
may show some
RECALL
53.6kHz/85.0Hz
PRESET MODE
You
can use this function when you want to
go back to the screen display of the time
you purchased the product after adjusting to
modify it in the Preset Mode.
When you are in the User mode, you can
recall only
and
CONVERGENCE items. After using Recall,
adjust the screen display again if necessary.
If you want more information on the Preset
Mode, refer to A11 page.
,
MOIRE
,
,
,
,
This item allows you to reduce the moire
(Moire is caused by interference Horizontal
Scan Line with the
periodical dot screen). It
normally OFF(H:0/V:0).
The moire adjustments may affect the focus
is
of the
The
screen.
image may shake
the moire reduction function is
screen
CONVERGENCE This item allows you to
slightly while
on.
adjust the horizontal
convergence.
The horizontal convergence control adjust
the alignment of the red and blue horizontal
fields.
A10
The monitor has 19 memory locations for
factory preset to popular video modes.
display modes, 4 of which are
Preset Modes (Resolution)
1234
VESA
640
x
480
43.269
85
VESA
800
x
600
53.674
85
VESA
1024
768
68.677
85
1024
91.146
85
VESA
1280
x
x
User Modes
Modes 5-19
are
empty and
can
accept
new
video data. If the monitor detects
a
video mode that has not been present before or is not one of the preset
modes, it stores the new mode automatically in one of the empty modes
new
starting
with mode 5.
If you use up the 15 blank modes and still have more new video modes, the
monitor replaces the information in the user modes starting with mode 5.
Recalling Display Modes
When your monitor detects a mode it has seen before, it automatically recalls
the image settings you may have made the last time you used that mode.
You may, however, manually force a recall of each of the 4 preset modes by
pressing the Recall button. All preset modes are automatically recalled as the
monitor
The
senses
ability to
the
incoming signal.
recall the preset modes is
dependent
on
the
signal coming from
factory
your PC's video card or system. If this signal does not match any of the
modes, the monitor automatically sets itself to display the image.
Check the
following before calling for service.
SELF DIAGNOSTICS message.
The signal cable is not connected, or is loose. Check and
secure
the connection.
OUT OF FREQUENCY message appears.
The frequency of the sync input is outside the operating range of the monitor.
*Horizontal
*Vertical
Use the
Frequency : 30-96kHz
Frequency : 50-160Hz
graphics
to the manual for
board's
utility software
graphics board).
to
change
the
frequency setting (Refer
The power LED is illuminated amber.
Display power management mode.
There is
no sync signal and the signal cable is not fastened securely.
Check the computer power and graphics adapter configuration.
image on the SCREEN
rectangle shape.
The
Image adjustment
is not centered,
not been done
MENU, SELECT and
yet in the
or
too
small,
operating mode. Use
image to your liking.
current
buttons to set the
The monitor doesn't enter the power
or
saving off
mode
not a
the
(Amber).
Computer video signal is not VESA DPMS standard. Either the PC or the video
controller card is not using the VESA DPMS power management function.
Specifications
Picture Tube
19 inch
(18.0 inches viewable)
degree deflection
0.26mm dot pitch
ARAS(Anti-Reflective Anti-Static) coating
90
Sync Input
Horizontal
30
Vertical
50
Input
Freq.
Freq.
Form
Signal Input
96kHz
(Automatic)
(Automatic)
Separate TTL, Positive/Negative
Composite TTL, Positive/Negative
15 pin D-Sub Connector
-
-
160Hz
RGB Analog,
Input Form
Resolution(max)
Separate,
USB
USB standard
Rev. 1.1
specifications
Downstream power supply 500mA for each (MAX)
Communication speed 12 Mbps (full), 1.5 Mbps
Video
-
Input
Applies to
900B plus only.
USB port
1600
1
x
0.7Vp-p/75 ohm,
complied self-powered
(low)
ports
Power
Max.
≤ 110W
Consumption
Normal
≤
Stand-by/Suspend
≤
8W
Power Off
≤
3W
Width
44.80
cm
/ 17.6 inches
Height
Depth
45.40
cm
/ 17.9 inches
47.00
cm
/ 18.5 inches
Europe
AC 200-240V 50Hz 1.0A
Others
AC 100-240V 50/60Hz 2.0A
Power
Input
90W
(130W)
(110W)
(30W)
(20W)
The
products should be used
requirements of each ID LABEL.
19
*(
Net
Environmental
Conditions
Operating Condition
0˚C to 40 ˚C
Temperature
10 % to 90 % non-Condensing
Humidity
kg (41.9 lbs)
Storage Condition
-20˚C to 60 ˚C
Temperature
5 % to 90 % non-Condensing
Humidity
NOTE
subject
to
change without
A13
): with
USB
(900B/900B plus)
(900B/900B plus)
according to the Power
Weight
Information in this document is
hub
Upstream port
4 Downstream
Dimensions (with
tilt/ swivel stand)
Positive
1200@75Hz
notice.
Download PDF

advertising