LG | FLATRON-775FT-FB775C-EP | LG FLATRON 775FT(FB775C-EA) Owner’s Manual

Thank you for purchasing a high resolution monitor. It will give you high
resolution performance and convenient reliable operation in a variety of
video
operating modes.
Features
The monitor is
17 inches
(16.0
inches viewable
) intelligent, microprocessor
compatible
analog RGB (Red, Green, Blue) display
standards, including IBM PC , PS/2 , Apple , Macintosh , Centris , Quadra , and
Macintosh II family.
a
based monitor
with most
The monitor
provides crisp text and vivid color graphics with VGA, SVGA, XGA,
Ergonomic modes (non-interlaced), and most Macintosh compatible
color video cards when used with the appropriate adaptor. The monitor's wide
compatibility makes it possible to upgrade video cards or software without
purchasing a new monitor.
and VESA
Digitally controlled auto-scanning is done with the micro-processor for horizontal
frequencies between 30 and 70kHz, and vertical scan frequencies
scan
between 50-160Hz.
This monitor is
dots and
a
capable
of
producing
a
maximum horizontal resolution of 1280
maximum vertical resolution of 1024 lines.
The
microprocessor-based digital controls allow you to adjust conveniently a
variety of image controls by using the OSD (On Screen Display).
Plug
and
play capability
if
supported by your system.
This monitor has DDC 2B function.*
Compliant with
-
-
-
the
following regulated specifications
:*
EPA ENERGY STAR
Swedish MPR II
Swedish TCO'99
*For detailed information, please refer to
the Reference Guide provided
.
Connecting
the Monitor
On the back of the monitor
power
1
2
cord,
plug-in connections; one for the AC
signal cable from the video card.
two
Power off both the monitor and PC.
Connect the 15
pin VGA connector of
supplied signal cable to the output
matching input connector on the rear
of the monitor. The connectors will mate only one way. If you cannot attach
the cable easily, turn the connector upside down and try again. When mated,
tighten the thumbscrews to secure the connection.
VGA video connector
2'
are
and the other for the
on
the
the PC and the
appropriate MAC to VGA adapter block at your local computer
adapter changes the high density 3 row 15 pin VGA connector to
the correct 15 pin 2 row connection to mate with your MAC. Attach the other
end of the signal cable to the side of the adapter block with 3 rows.
Locate the
store. This
Connect the attached
cable to the video output
adapter block/signal
on
your
MAC.
3
One end of the AC power cord is connected into the AC power connector on
the back of the monitor. The other end is plugged into a properly grounded
three-prong AC outlet.
4
5
Power ON the PC, then the monitor.
If you
see
the SELF DIAGNOSTICS message, check the
signal
cable and
connectors.
6
After
using
the system, power OFF the monitor, then the PC.
MACINTOSH
IBM PC
Mac
D-15P
2
2'
Adapter
D-15P
3
Power Cord
Signal
Cable
*
NOTE
:
For
Apple
Macintosh use,
separate plug adapter is needed
change the
15
pin high density (3 row)
on the supplied
pin 2 row connector.
D-sub VGA connector
cable to
A2
a
15
a
to
Location and Function of Controls
Front View
OSD
Power Button
SET
Power Indicator
OSD Button
SET Button
Buttons
Rear View
ID Label
D-Sub
AC Power
Socket
A3
Signal
Connector
Control Panel Function
Front Panel Controls
Power Indicator
OSD Button
Use this button to enter
exit the
on screen
or
display.
The power indicator
light is shown in the power
lights up green when the
monitor operates normally. If the monitor is in DPM
(Energy Saving) mode (stand-by/ suspend/power off),
this indicator color changes to amber.
button. This indicator
OSD
SET
Buttons
Power Button
SET Button
Use these buttons to choose
Use this button to enter
adjust items
screen display.
selection in the
or
in the
on
display.
A4
a
on screen
Use this button to turn
the monitor
on or
off.
On Screen
Display (OSD) Control Adjustment
Making adjustments to the image size, position and operating parameters of
the monitor are quick and easy with the On Screen Display Control system. A
quick example is given below to familiarize you with the use of the controls.
Following section is an outline of the available adjustments and selections you
can make using the OSD.
NOTE
Allow the monitor to stabilize for at least 30 minutes before
To make
adjustments
in the On Screen
Display,
follow these steps:
OSD
SET
SET
OSD
12
Press the OSD Button, then the main
To
making image adjustment.
acces a
becomes
3
Use the
45
Accept
control,
use
the
the
changes by pressing
Exit the OSD
by Pressing
of the OSD appears.
Buttons. When the icon you want
or
highlighted, press the SET
Buttons to
menu
Button.
adjust
the item to the desired level.
the SET Button.
the OSD Button.
A5
On Screen
You
were
Display(OSD)
introduced to the
Selection and
Adjustment
procedure of selection and adjusting an item
the OSD
using
descriptions
system. Listed below are the icons, icon names, and icon
of the items that are shown on the Menu.
OSD
Adjust
Description
BRIGHTNESS CONTRAST
Brightness
Used to adjust the brightness
66
of the
screen.
92
Contrast
Adjust the display to the
PRESET
COLOR
contrast desired.
6500K/ 9300K
To appear the
PRESET
6500K
9300K
?
?
TEMP
displays color temperature.
6500K:Slightly reddish white.
9300K:Slightly bluish white.
RED
User
TEMP
GREEN
easily color set without adjustment Red,
(R/G/B).
Green and Blue
BLUE
RED
To set your
own
color levels.
GREEN
To set your
own
color levels.
BLUE
To set your
own
color levels.
POSITION
Vertical Position
To move image up and down.
66
Horizontal Position
To move picture image left and
45
SIZE
Vertical Size
To
49
adjust image height.
Horizontal Size
64
To
A6
adjust image width.
right.
On Screen
Display(OSD)
OSD
Selection and
Adjust
Adjustment
Description
Side Pincushion
SHAPE
To correct the
Side
bowing
pincushion
in and out of the
image.
balance
To correct the balance of both sides
bowling.
Trapezoid
To correct
geometric distortion.
Parallelogram
This control
screen
adjusts for
image.
a
skewing
of the
Tilt
To correct
image
rotation.
Corner Top
To correct the
irregular distortion
displayed image.
of the
Corner Bottom
To correct the
irregular distortion
displayed image.
SETUP
VIDEO LEVEL
0.7V
DDC
ON
LANGUAGE
ENGLISH
VIDEO LEVEL This item is used to select the monitor's input
signal level. The normal level used for most
PC's is 0.7V. When the screen suddenly gets
brightened or blurry, please select 1.0V and
try again.
DDC
OSD POSITION
of the
To select the DDC
function(ON/OFF).
LANGUAGE To choose the
names are
OSD POSITION To
language
displayed.
adjust position
in which the control
of the OSD window
on
the
screen.
DEGAUSS To
SPECIAL
manually demagnetize the screen which
some image or color incorrectly.
may show
DEGAUSS
ON
RECALL
ON
MOIRE
H: 0/V: 0
PURITY
50
RECALL
If the monitor is
in
a
factory preset
image to the
reset the
factory preset mode.
68.6kHz/85.0Hz
PRESET MODE
operating
mode, this control will
MOIRE
This item allows you to reduce the moire
(Moire
by interference Horizontal Scan Line
with the periodical dot screen). It is normally
OFF(H:0/V:0).
The moire adjustments may affect the focus of
the screen. The screen image may shake
slightly while the moire reduction function is on.
is caused
Use to
PURITY
adjust the
overall
if the color appears
A7
purity of the image
uneven.
The monitor has 35 memory locations for
factory preset to popular video modes.
display modes,
10 of which
are
Display Modes (Resolution)
123456789
10
VESA
640
x
480
37.50
75
VESA
800
x
600
46.88
75
VESA
800
x
600
53.68
85
VESA
1024
68.677
85
VESA
640
x
400
31.47
70
VESA
640
x
480
31.47
60
VESA
800
x
600
37.88
60
VESA
640
x
480
43.27
85
VESA
1024
768
60.02
75
1024
63.98
60
VESA
1280
x
x
x
768
User Modes
Modes 11-35
are
empty and
can
accept
new
video data. If the monitor detects
video mode that has not been present before or is not one of the preset
modes, it stores the new mode automatically in one of the empty modes
a new
starting
with mode 11.
If you use up the 25 blank modes and still have more new video modes, the
monitor replaces the information in the user modes starting with mode 11.
Recalling Display Modes
When your monitor detects a mode it has seen before, it automatically recalls
the image settings you may have made the last time you used that mode.
You may, however, manually force a recall of each of the 10 preset modes by
pressing the Recall button. All preset modes are automatically recalled as the
monitor
The
senses
ability to
the
incoming signal.
recall the preset modes is
dependent
on
the
signal coming from
factory
your PC's video card or system. If this signal does not match any of the
modes, the monitor automatically sets itself to display the image.
Troubleshooting
Check the
following before calling for service.
SELF DIAGNOSTICS message.
The signal cable is not connected, or is loose. Check and
secure
the connection.
OUT OF FREQUENCY message appears.
The frequency of the signal from the video card is outside the operating range of
the monitor.
*
*
Horizontal Frequency : 30-70kHz
Vertical Frequency : 50-160Hz
Use the
graphics
to the manual for
board's
utility software
graphics board).
to
the
change
frequency setting (Refer
The power LED is illuminated amber.
Display power management mode.
There is
no
active
signal coming
from the PC.
The signal cable is not fastened securely.
Check the computer power and graphics
image on the SCREEN
rectangle shape.
The
Image adjustment
OSD, SET and
adapter configuration.
is not centered,
not been done
yet in the
buttons to set the
current
image
or
too
operating mode.
liking.
or
not a
Use the
to your
saving off
The monitor doesn't enter the power
small,
mode
(Amber).
Computer video signal is not VESA DPMS standard. Either the PC or the video
controller card is not using the VESA DPMS power management function.
An abnormal
picture is displayed on the screen. For example, the
of
the
upper part
picture may be missing or dark.
If using certain non-VESA Standard video card, an abnormal picture may be
displayed. Try setting it to one of the factory preset modes, or selecting to a
resolution and refresh rate within the specification limits of the monitor.
NOTE
If the power
the monitor.
indicator(LED) light
is
blinking amber,
Then press a power ON/OFF button
technician for more information.
on
the front
A9
may result in abnomal condition of
panel
control and call your service
Specifications
Picture Tube
17 inch
90
(16.0
degree
inches
viewable)
deflection
0.24mm Slot
pitch
W-ARAS(Wide Anti-Reflective Anti-Static) coating
Sync Input
Horizontal
Vertical
Freq.
Freq.
Input
Input
50
-
70kHz
(Automatic)
160Hz
Form
(Automatic)
Separate TTL, Positive/Negative
15 pin D-Sub Connector
Form
Separate,
Input
Signal Input
Video
30
-
RGB
Analog, 0.7Vp-p/75 ohm,
Resolution(max)
1280
Power
Normal
≤ 105W
Consumption
Stand-by/Suspend
≤
Power Off
≤5W
Width
41.5
cm
/ 16.3 inches
Height
Depth
43.5
cm
/ 17.1 inches
43.9
cm
/ 17.3 inches
Europe
AC 200-240V 50Hz 1.5A
Others
AC 100-240V 50/60Hz 2.0A
Dimensions (with
tilt/ swivel stand)
Power
Input
x
1024@60Hz
15W
The
products should be used according
requirements of each ID LABEL.
17.8
to the Power
Weight
Net
Environmental
Operating Condition
10 ˚C to 40 ˚C
Temperature
10 % to 90 % non-Condensing
Humidity
Conditions
kg (39.24 lbs)
Storage Condition
0 ˚C to 60 ˚C
Temperature
5 % to 90 % non-Condensing
Humidity
NOTE
Information in this document is
subject
to
Positive
change without
A10
notice.
Download PDF

advertising