LG | M227WA-PM | LG M227WA-PM Owner’s Manual

OWNER’S MANUAL
M227WA
M237WA
Make sure to read the Safety Precautions before
using the product.
Keep the User's Guide(CD) in an accessible place
for furture reference.
See the label attached on the product and give the
information to your dealer when you ask for service.
PREPARATION
FRONT PANEL CONTROLS
■
This is a simplified representation of the front panel. The image shown may be somewhat different from your
set.
INPUT
INPUT
Button
MENU ENTER
MENU
Button
ENTER
Button
VOLUME
Buttons
VOL
CH
CHANNEL
Buttons
Power
Button
Headphone
Jack
1
PREPARATION
BACK PANEL INFORMATION
■
This is a simplified representation of the back panel. The image shown may be somewhat different from your
set.
<M227WA>
<M237WA>
1
1
2
3
4
7
AV IN
Y
VIDEO
(MONO) L
RGB IN (PC)
VIDEO
PB
1
HDMI IN
6
COMPONENT
IN
AUDIO IN
(RGB/DVI)
AC IN
5
PR
2
AC IN
L
R
ANTENNA/
CABLE IN
AUDIO
RS-232C IN
(CONTROL & SERVICE)
AUDIO R
DVI-D IN (PC)
S-VIDEO
AC IN
8
2
9
1
Power Cord Socket
This set operates on AC power. The voltage is indicated on the Specifications page. Never attempt to
operate the set on DC power.
2
HDMI Input
Connect a HDMI signal to HDMI IN.
Or DVI (VIDEO) signal to HDMI IN with DVI to
HDMI cable.
10
6
AV(Audio/Video) Input
Connect audio/video output from an external
device to these jacks.
7
Antenna Input
Connect over-the-air signals to this jack.
8
DVI-D Input(PC)
Connect the output from a PC.
3
RGB/DVI Audio Input
Connect the audio from a PC.
9
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
4
RGB Input (PC)
Connect the output from a PC.
10
S-Video Input
Connect S-Video out from an S-VIDEO device.
5
Component Input
Connect a component video/audio device to these
jacks.
PREPARATION
<M227WA>
STAND INSTALLATION
■
The image shown may be somewhat different from your set.
1
Carefully place the product screen side down on a
cushioned surface that will protect product and
screen from damage.
2
Insert the s t a n d b a s e into the product
3
Attach the monitor to the Stand Base by turning
the screw to the right.
* Turn the screw by using the screw handle
Screw
3
PREPARATION
<M237WA>
STAND INSTALLATION
■
The image shown may be somewhat different from your set.
1
Carefully place the product screen side down on a
cushioned surface that will protect product and
screen from damage.
2
Insert the s t a n d b a s e into the product
3
Attach the monitor to the Stand Base by turning
the screw to the right.
* Turn the screw by using the screw handle
Screw
4
<M227WA>
PREPARATION
DETACHING STAND
■
The image shown may be somewhat different from your set.
1
Place the set screen side down on a cushion or
soft cloth.
2
Detach the monitor to the Stand Base by turning the screw to the left.
3
Turn the screw by using the screw handle
4
Pull the stand base.
5
5
<M237WA>
PREPARATION
DETACHING STAND
■
The image shown may be somewhat different from your set.
1
Place the set screen side down on a cushion or
soft cloth.
2
Detach the monitor to the Stand Base by turning the screw to the left.
3
Turn the screw by using the screw handle
4
Pull the stand base.
5
6
PREPARATION
WALL MOUNT: HORIZONTAL INSTALLATION
For proper ventilation, allow a clearance of 4 inches on each side and from the wall. Detailed installation
instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
4 inches
4 inches
4 inches
4 inches
4 inches
DESKTOP PEDESTAL INSTALLATION
For proper ventilation, allow a clearance of 4 inches on each side and from the wall.
4 inches
4 inches
4 inches
4 inches
7
PREPARATION
POSITIONING YOUR DISPLAY
■
The image shown may be somewhat different from your set.
Adjust the position of the panel in various ways for maximum comfort.
• Tilt range
-6° ~ -2°
12°~ 18°
LOCATION
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to
expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover.
If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop.
- Be sure to use screws and a wall mount that meet VESA standards.
- Using screws longer than those recommended might damage the product.
- Using screws that do not meet VESA standards might either damage the product or result in it coming away from
the wall. We will not be held responsible for any damage resulting from failure to follow these instructions.
< Screw Mounting Interface Dimension >
M227WA : 100mm x 100mm hole spacing
M237WA : 75mm x 75mm hole spacing
Warning:
When adjusting the angle of the screen,do not put your
finger(s)in between the head of the monitor and the stand
body.You can hurt your finger(s).
8
PREPARATION
KENSINGTON SECURITY SYSTEM
- The product is equipped with a Kensington Security System connector on the back panel. Connect the
Kensington Security System cable as shown below.
- For detailed installation and use of the Kensington Security System, refer to the user’s guide provided with
the Kensington Security System.
For further information, contact h t t p : / / w w w . k e n s i n g t o n . c o m, the internet homepage of the
Kensington company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors.
NOTE
- The Kensington Security System is an optional accessory.
NOTES
a. If the product feels cold to the touch, there may be a small “flicker” when it is turned on.
This is normal, there is nothing wrong with product.
b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots.
However, they have no adverse effect on the monitor's performance.
c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
<M227WA>
<M237WA>
9
EXTERNAL EQUIPMENT SETUP
■
To prevent equipment damage, never plug in any power cords until you have finished connecting all equipment.
ANTENNA CONNECTION
For optimum picture quality, adjust antenna direction.
■ An antenna cable and converter are not supplied.
■
AV 1
Wall
Antenna
Socket
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
ANTENNA/
CABLE IN
AC IN
RF Coaxial Wire (75 ohm)
Outdoor
Antenna
(VHF, UHF)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
AV 1
UHF
Antenna
Signal
Amplifier
AC IN
ANTENNA/
CABLE IN
VHF
■
■
10
In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown above.
If signal needs to be split for two sets, use an antenna signal splitter for connection.
EXTERNAL EQUIPMENT SETUP
■
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
■
The image shown may be somewhat different from your set.
HD RECEIVER SETUP
When connecting with a component cable
1
Connect the SET-TOP outputs to the C O M P O N E N T I N
V I D E O sockets (Y PB PR) on the set.
2
Connect the audio cable from the SET-TOP to C O M P ON E N T I N A U D I O sockets of the set.
3
Press the I N P U T button to select C o m p o n e n t .
Signal
Component
480i/576i
Yes
480p/576p
Yes
720p/1080i
Yes
1080p
Yes
COMPONENT
IN
Y
VIDEO
1
AUDIO
PB
2
PR
L
R
11
EXTERNAL EQUIPMENT SETUP
When connecting with a HDMI
1
Connect the HDMI output of the digital set-top box to the
H D M I I N jack on the set.
1
2
HDMI IN
2
Press the INPUT button to select HDMI1 or HDMI2.
1
Signal
HDMI
480i/576i
No
480p/576p
Yes
720p/1080i
Yes
1080p
Yes
When connecting with a HDMI to DVI cable
1
Connect the digital set-top box to H D M I I N jack on
the set.
1
AUDIO IN
(RGB/DVI)
HDMI IN
2
2
Connect the audio output of the digital set-top box to
the A U D I O I N ( R G B / D V I ) jack on the set.
3
Turn on the digital set-top box. (Refer to the owner’s
manual for the digital set-top box.)
4
Press the INPUT button to select HDMI1 or HDMI2.
2
1
AUDIO
DVI OUTPUT
L
! NOTE
G
12
HDMI Input does not support PC mode. If it is connected PC, the screen may not be displayed properly.
R
EXTERNAL EQUIPMENT SETUP
DVD SETUP
When connecting with a component cable
1
Connect the video output sockets (Y PB PR) of the DVD to
the C O M P O N E N T I N V I D E O sockets (Y PB PR) of the set.
2
Connect the audio cable from the DVD to C O M P O N E N T
I N A U D I O sockets of the set.
3
Press the I N P U T button to select Component.
4
Press the P L A Y button on the DVD.
The DVD playback picture appears on the screen.
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the set
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
COMPONENT
IN
Y
VIDEO
1
AUDIO
PB
2
PR
L
R
13
EXTERNAL EQUIPMENT SETUP
When connecting HDMI cable
1
HDMI IN
1
Connect the HDMI output of the DVD to the
H D M I I N jack on the set.
2
Press the INPUT button to select HDMI1 or HDMI2.
2
1
! NOTE
G Set can receive the video and audio signal simultaneously by using a HDMI cable.
G If the DVD player does not support Auto HDMI, you need to set the DVD output resolution appropriately.
14
EXTERNAL EQUIPMENT SETUP
VCR SETUP
To avoid picture noise (interference), leave an adequate distance between the VCR and set.
■ Typically a still picture is shown on the VCR. If a user uses 4:3 picture format for a long time, an afterimage
may remain on the sides of the screen.
■
When connecting with an antenna
ANTENNA IN/
CABLE IN
ANT OUT
S-VIDEO
ANT IN
OUTPUT
SWITCH
VIDEO
L
R
1
2
Wall Jack
Antenna
1
Connect the ANT OUT socket of the VCR to the ANTENNA IN socket of the set.
2
Connect the antenna cable to the RF ANT IN in socket of the VCR.
3
Press the P L A Y button on the VCR and match the appropriate program between
the set and VCR for viewing..
AV 1
15
EXTERNAL EQUIPMENT SETUP
When connecting with a RCA cable
R
ANT OUT
ANT IN
Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
1
L
3
S-VIDEO VIDEO
Press the INPUT button to select AV.
AUDIO R
2
AV IN
(MONO) L
Connect the audio/video out sockets of the VCR to
AUDIO/VIDEO in sockets of the set.
VIDEO
1
S-VIDEO
! NOTE
G
If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the set.
When connecting with an S-Video cable
1
Connect the S-Video socket of the VCR to the SVIDEO socket of the set.
L
R
S-VIDEO
16
Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
VIDEO
4
3
2
S-VIDEO
4
OUTPUT
SWITCH
1
AUDIO R
Press the INPUT button to select AV.
(MONO) L
3
Connect the audio cable from the S-VIDEO VCR to the
AUDIO sockets of the set.
VIDEO
2
ANT IN
ANT OUT
AV IN
EXTERNAL EQUIPMENT SETUP
PC SETUP
This product provides Plug and Play capability, meaning that the PC adjusts automatically to the set's settings.
When connecting with a D-sub 15 pin cable
1
Connect the signal cable from the RGB output socket of the
PERSONAL COMPUTER to the RGB IN(PC) jack of the set.
2
Connect the audio cable from the PC to the A U D I O I N
( R G B / D V I ) jack of the set.
3
Press the INPUT button to select RGB PC.
4
Switch on the PC, and the PC screen appears on the set.
The set can be operated as a PC monitor.
RGB IN (PC)
AUDIO IN
(RGB/DVI)
1
2
RGB OUTPUT
AUDIO
! NOTE
G
You must use shielded signal interface cables (D sub 15 pin cable, DVI cable) with ferrite cores to maintain
standard compliance for the product.
17
EXTERNAL EQUIPMENT SETUP
When connecting with a DVI cable
1
2
Connect the DVI output of the PC to the D V I - D I N
jack on the set.
DVI-D IN (PC)
AUDIO IN
(RGB/DVI)
Connect the audio cable from the PC to the A U D I O
I N ( R G B / D V I ) jack of the set.
1
2
AUDIO
DVI OUTPUT
! NOTE
If the set is cold, there may be a small “flicker”
when the set is switched on. This is normal, there
is nothing wrong with the set.
G If possible, use the 1920x1080@60Hz video
mode to obtain the best image quality for your
LCD monitor. If used with other resolutions, some
scaled or processed pictures may appear on the
screen. The set has been preadjusted to the mode
1920x1080@60Hz.
G Some dot defects may appear on the screen, like
Red, Green or Blue spots. However, this will have
no impact or effect on the monitor performance.
G
18
G
Do not press the LCD screen with your finger for
a long time as this may produce some temporary
distortion effects on the screen.
G
Avoid keeping a fixed image on the set’s screen
for prolonged periods of time. The fixed image
may become permanently imprinted on the
screen; use a screen saver when possible.
EXTERNAL EQUIPMENT SETUP
BACK COVER FOR WIRE ARRANGEMENT
<M227WA>
Tie cables together with a cable management as
shown in the illustration.
Cable management
<M237WA>
Tie cables together with a cable tie as shown in the
illustration.
Cable tie
19
EXTERNAL EQUIPMENT SETUP
RGB/DVI[PC]
Resolution
720x400
640x480
800x600
1024x768
1152x864
1280x1024
1680x1050
1600x1200
1920x1080
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
31.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
64.674
65.290
75.000
66.587
70
60
75
60
75
60
75
75
60
75
60
60
60
60
HDMI[DTV] supported mode
Resolution
720x480/60p
720x576/50p
1280x720/50p
1280x720/60p
1920x1080/60i
1920x1080/50i
1920x1080/24p
1920x1080/30p
1920x1080/50p
1920x1080/60p
20
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
31.47
31.5
31.25
37.5
44.96
45
33.72
33.75
28.125
27
33.75
56.25
67.43
67.5
60
60
50
50
60
60
60
60
50
24
30
50
60
60
WATCHING TV /CHANNEL CONTROL
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the set.
TV/PC
POWER INPUT
TV/PC Selects TV or PC mode.
Switches the set on.
POWER Switches the set on or off.
MUTE
PIP
CAPTION
MTS
INPUT External input mode rotates in regular sequence.
Switches the set on.
MUTE Switches the sound on or off.
PIP Switches the sub picture PIP, DW mode.(Refer to the p.27)
CAPTION Select a closed caption.
Off - > Mode1 - > Mode2 - > Text1 - > Text2
(Refer to the p.44)
Q.VIEW
FAV
MTS Press repeatedly to select Mono, Stereo, SAP sound tone.
But Stereo, SAP mode are available only if included on the
broadcast signal.
CH
VOL
ENTER
0~9 number Selects a channel.
button Selects numbered items in a menu.
VOL
Q.VIEW Returns to the previously viewed channel.
FAV Scroll through the programmed Favorite channels.
CH
MENU
RETURN
SLEEP
VOLUME UP Adjusts the volume.
/DOWN
PICTURE
SOUND
ARC/
Channel Selects a channel.
UP/DOWN
*
ENTER Button Accepts your selection or displays the current mode.
Double press the E N T E R button, then Auto Config.
(Only RGB input)
MENU Selects a menu. (Refer to the p.23)
RETURN Allows the user to move return one step in an interactive
application or other user interaction function.
SLEEP Sets the sleep timer. (Refer to the p.42)
PICTURE Toggles through the factory preset picture settings depending on the viewing environment.
SOUND Toggles through preset sound settings.
ARC/* Selects your desired picture format.(Refer to the p.28)
Inserting batteries into remote control.
1. Take out the battery cap.
2. Insert the batteries with correct polarity (+/-).
3. Close the battery cap.
• Dispose of used batteries in the recycle bin to prevent
environmental pollution.
21
WATCHING TV /CHANNEL CONTROL
TURNING ON THE SET
When your set is turned on, you will be able to use its features.
Firstly, connect the power cord correctly.
■ To turn set on, press the
, I N P U T, C H
1
P O W E R, I N P U T, C H
D / E,
D / E
button on the set or press the
N U M B E R( 0~9
9 ) buttons on the remote control.
Initializing Guide
If the OSD (On Screen Display) is displayed on the screen after turning on the set, you can adjust the
L a n g u a g e, L o c a t i o n, A u t o T u n i n g.
Note:
a. It will automatically disappear after approx. 40 seconds unless a button is pressed.
b. “In-Store” mode is only for shop display and not for general customer use.
c. "Home” mode is the optimal setting for home environments, and is the set's default mode.
d. "In-Store" mode is the optimal setting for store environments. If a user modifies image quality data,
“In-Store” mode initializes the product to the image quality set by us after a certain period of time.
e. The mode (Home, In-Store) can be changed by executing Factory Reset in the Option menu.
CHANNEL SELECTION
1
Press the C H
D / E
or N U M B E R buttons to select a channel number.
VOLUME ADJUSTMENT
22
1
Press the V O L
2
If you wish to switch the sound off, press the M U T E button.
3
You can cancel the Mute function by pressing the M U T E o r V O L
F
/
G button to adjust the volume.
F
/
G
button.
WATCHING TV /CHANNEL CONTROL
ON SCREEN MENUS SELECTION
Your set's OSD (On Screen Display) may differ slightly from what is shown in this manual.
1
Press the M E N U button and then D /
2
Press the G button and then D /
3
Change the setting of an item in the sub or pull-down menu with F /
You can move to a higher level menu by pressing the E N T E R.
E
button to display each menu.
E button to select a menu item.
G button.
Setup
Picture
Audio
Auto Tuning
Manual Tuning
Favorite Channel
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
Sound Mode
Auto Volume
Balance
TV Speaker
DE F G
DE F G
DE F G
RETURN
Option
Language
PIP
Key Lock
Caption/Text
Set ID
DDC-CI
Power Indicator
Factory Reset
DE F G
RETURN
RETURN
0
RETURN
Time
Clock
Off Time
On Time
Sleep Timer
Auto Sleep
DE F G
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
! NOTE
G
The OSD (On Screen Display) function enables you to adjust the screen status conveniently since it provides graphical presentation.
23
WATCHING TV /CHANNEL CONTROL
AUTO TUNING
Up to set stations can be stored by channel numbers (1 - 125).
Stations can be tuned using automatic or manual modes.
It is recommended that you use Auto tuning during installation of this set.
Setup
1
Press the M E N U button and then D /
S e t u p menu.
2
Press the G button and then D /
T u n i n g.
3
Press the G button to begin auto tuning.
E button to select the
Auto Tuning
Manual Tuning
Favorite Channel
G
To Start
E button to select A u t o
DE F G
RETURN
To stop auto tuning, press the R E T U R N button.
Auto Tuning
TV
5
RETURN Stop
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
24
35%
WATCHING TV /CHANNEL CONTROL
MANUAL TUNING:ADDING/DELETING CHANNELS
You can add or delete channels from the channel scan manually.
E button to select the S e t u p
1
Press the M E N U button and then D /
menu.
2
Press the G button and then D /
T u n i n g.
E button to select M a n u a l
3
Press the G button and then D /
E button to select C h a n n e l
Setup
Auto Tuning
Manual Tuning
Favorite Channel
G
TV
Memory
Fine
Booster
10
0
Off
n u m-
ber.
DE F G
4
Press the D /
5
Press the D / E button to select F i n e.
(Normally fine tuning is only necessary if reception is poor.)
6
Press the G button and then use D /
7
Press the G button and then use D / E button to select O n or
O f f.
(If reception is poor,select B o o s t e r to On. When the signal is
strong,select “OFF ”. )
RETURN
E button to select E r a s e / M e m o r y.
E button to select B o o s t e r.
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
25
WATCHING TV /CHANNEL CONTROL
FAVOURITE CHANNELS SETUP
This function lets you select your favourite channels directly.
Repeatedly press the FAV button to select stored favorite channels.
1
Press the M E N U button and then D /
S e t u p menu.
E
button to select the
E button to select F a v o u r i t e
2
Press the G button and then D /
Channel.
3
Press the G button.
4
Press the D /
5
Select a desired channel with the F /
tons.
6
To store another channel, repeat steps 4 to 5 .
You can store up to 8 channel.
E button to select - -
- - - - -.
Setup
Auto Tuning
Manual Tuning
Favorite Channel
DE F G
G
V ---------
---------------------------------
RETURN
G button or NUMBER but-
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
26
PICTURE CONTROL
WATCHING PIP (PICTURE-IN-PICTURE)
PIP lets you view 2 different inputs (sources) on your
screen at the same time.
One source will be large, and the other source will show
a smaller insert image.
PIP function is available in the RGB-PC, DVI input only.
(It can support TV, AV mode)
PIP
PIP
PIP Input
PIP Channel
PIP Audio
PIP Size
PIP Position
DEF G
F
Off
TV
TV
Off
Small
G
2
RETURN
Watching PIP/Double Window
Each time you press the PIP button it will change to PIP -> DW1 -> DW2 -> PIP Off.
PIP Mode
DW1 Mode
DW2 Mode
PIP Off
Channel Selection for Sub Picture
Enter the PIP menu and then press the D / E/ F / G button to select a Channel for the sub picture.
The selected Channel number is displayed just below RGB-PC or DVI input.
Input Source Selection for Sub Picture
Enter the PIP menu and then press the D / E/
(Sub picture can be selected only TV, AV)
F
/
G
button to select the PIP Input source for the sub picture.
Audio Source Selection for Sub Picture
Enter the PIP menu and then press the
D / E/ F
/
G
button to select the PIP Audio source for the sub picture.
Sub Picture Size Adjustment (PIP mode only)
Enter the PIP menu and then press the D / E/
F
/
G button to adjust the sub picture size.
Moving the Sub Picture (PIP mode only)
Enter the PIP menu and then press the D / E/
F
/
G button to adjust the sub picture position.
! NOTE
A caption function does not operate in PIP mode.
G In PIP mode, below remote controller keys are not available.
* NUMBER, MTS, CAPTION, FAV, Q.VIEW
G
27
PICTURE CONTROL
PICTURE SIZE (ASPECT RATIO)CONTROL
You can watch the screen in various picture formats; 1 6 : 9 , 4 : 3, Z o o m 1 / 2 and J u s t S c a n.
Just Scan works in the following mode: Component (720p/1080i/1080p), HDMI (720p/1080i/1080p)
If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and
remain visible.
You can adjust the enlarge proportion using D /
E button.
This function works in the following signal.
1
You can adjust Aspect Ratio in the Picture menu.
• 16:9
The following selection will allow you to adjust the
picture horizontally, in linear proportion, to fill the
entire screen(useful for viewing 4:3 formatted
DVDs).
16:9
Zooml
• Zoom2
Choose Zoom 2 when you wish the picture to be
altered, both horizontally extended and vertically
cropped. The picture adopting a compromise
between alteration and screen converage.
• 4:3
The following selection will allow you to view a picture with an original 4:3 aspect ration, grey bars will
appear on both the left and right hand of the
screen.
4:3
Zoom2 DE
• Just Scan
Following Selection will lead to you view the picture
of best quality without loss of original picture in
high resolution image.
• Zoom1
The following selection will allow you to view the
picture without any alteration, while filling the entire
screen. However, the top and bottom of the picture
will be cropped.
! NOTE
G
G
28
DE
You can only select 4:3,16:9 (Wide) in Component, HDMI, RGB(PC) mode.
In HDMI/Component (over 720p)mode, Just Scan is available.
Just Scan
PICTURE CONTROL
PRESET PICTURE SETTINGS
Picture Mode-Preset
Picture Mode adjusts the set for the best picture appearance. Select the preset value in the P i c t u r e M o d e menu based on the
channel category.
Vivid, Standard, Cinema, Sport and Game are programmed for optimum picture reproduction at the factory and cannot be
changed.
Press the PICTURE button repeatedly to select the picture appearance setup option.
Picture
1
Press the M E N U button and then D /
P i c t u r e menu.
2
Press the G button and then D /
M o d e.
3
Press the G button and then D / E button to select V i v i d ,
S t a n d a r d , C i n e m a , S p o r t , G a m e , U s e r 1 or U s e r 2.
E
button to select the
E button to select P i c t u r e
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
DE F G
G
V Vivid
Standard
Cinema
Sport
Game
User1
User2
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
29
PICTURE CONTROL
MANUAL PICTURE ADJUSTMENT
Picture Mode-User Mode
Backlight
Contrast
Brightness
Color
Sharpness
Tint
Adjust the brightness of LCD panel to control the brightness of the screen.
Adjusts the difference between light and dark levels in the picture.
Increases or decreases the amount of white in the picture.
Adjusts intensity of all colors.
Adjusts the level of crispness in the edges between the light and dark areas of the picture. The lower
the level, the softer the image.
Adjusts the balance between red and green levels.
1
Press the M E N U button and then D /
P i c t u r e menu.
2
Press the G button and then D /
M o d e.
E button to select P i c t u r e
3
Press the G button and then D /
U s e r 2.
E button to select U s e r 1 or
4
Press the G button and then D / E button to select the desired
picture option.
• T V / A V / C o m p o n e n t / H D M I:Backlight, Contrast, Brightness,
Color, Sharpness and Tint
• R G B - P C / D V I:Backlight, Contrast, Brightness
5
Press the
F
/
E
Picture
button to select the
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
DE F G
G
Vivid
Standard
Cinema
Sport
Game
V User1
User2
RETURN
Picture Mode
Backlight
Contrast
Brightness
Color
Sharpness
Tint
100G
100
50
70
70
0
G button to make appropriate adjustments.
DE F G
RETURN
<TV/AV/Component/HDMI>
Picture Mode
D
Backlight
E
100
F
G
Backlight
Contrast
Brightness
DE F G
100G
100
50
RETURN
<RGB-PC/DVI>
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
30
PICTURE CONTROL
Auto Color Tone Control(Cool/Medium/Warm)
To initialize values (reset to default settings), select the Cool option.
Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set
to cool to see less intense colors with more blue.
This menu is activated after selecting “User1” or “User2” in the Picture Mode.
1
Press the M E N U button and then D /
the P i c t u r e menu.
E
Picture
button to select
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
E button to select C o l o r
2
Press the G button and then D /
T e m p e r a t u r e.
3
Press the G button and then D / E button to select
either C o o l, M e d i u m, W a r m or U s e r.
DE F G
G
V Cool
Medium
Warm
User
RETURN
Auto Color Tone Control (9300K/6500K/sRGB) (RGB-PC, DVI input only)
To initialize values (reset to default settings), select the 6500K option.
This menu is activated after selecting “User1” or “User2” in the Picture Mode.
1
Press the G button and then D / E button to select either
9 3 0 0 K , 6 5 0 0 K , s R G B or U s e r.
Picture
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
DE F G
G
9300K
V 6500K
sRGB
User
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
31
PICTURE CONTROL
Color Tone - User Mode
To adjust red, green, blue to any color temperature you prefer.
This menu is activated after selecting “User1” or “User2” in the Picture Mode.
Picture
1
Press the M E N U button and then D /
P i c t u r e menu.
2
Press the G button and then D /
T e m p e r a t u r e.
E button to select C o l o r
3
Press the G button and then D /
E button to select U s e r.
4
Press the G button and then D /
or B l u e.
5
E
button to select the
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
DE F G
Press the F /
G
G
Cool
Medium
Warm
V User
RETURN
<TV/AV/Component/HDMI>
E button to select R e d, G r e e n
Picture
button to make appropriate adjustments.
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
DE F G
G
9300K
6500K
sRGB
V User
RETURN
<RGB-PC/DVI>
User
Red
Green
Blue
0
0
0
DE F G
....................
G
RETURN
D
Red
0F
........................
E
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
32
G
PICTURE CONTROL
- PICTURE IMPROVEMENT TECHNOLOGY
XD is LG electronic's unique picture improving technology to display a real HD source through an advanced digital
signal processing algorithm.
It is not possible to use this function in RGB-PC/DVI input.
1
Press the MENU button and then D /
P i c t u r e menu.
E button to select the
2
Press the G button and then D /
E button to select X D.
3
Press the G button and then D /
M a n u a l.
E button to select A u t o
or
Picture
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
DE F G
G
V Auto
Manual
G
Off
Low
V High
RETURN
* Manual Selection
This menu is activated after selecting the U s e r 1 or U s e r 2 of P i c t u r e
M o d e.
Manual
XD Contrast
XD Color
XD NR
1
Press the G button and then D / E button to select X D
C o n t r a s t , X D C o l o r or X D N R.
2
Press the G button and then D / E button to select O f f, L o w or
H i g h.
Select O f f, L o w, H i g h or A d a p t i v e (Only X D N R).
DE F G
RETURN
X D C o n t r a s t : Optimises the contract automatically according to the brightness of the reflection.
X D C o l o r : Adjusts the color of the reflection automatically to reproduce as close as possible to natural colors.
A X D N R : Removes interference up to the point where it does not damage the original picture.
A
A
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
33
PICTURE CONTROL
ADVANCED - GAMMA
Picture
High gamma values display whitish images and low gamma values display high contrast images.
It is not possible to use this function in RGB-PC/DVI-PC input.
1
Press the M E N U button and then D /
P i c t u r e menu.
E
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
G
To Set
button to select the
DE F G
2
Press the G button and then D /
E button to select A d v a n c e d.
3
Press the G button and then D /
E button to select G a m m a.
4
Press the G button and then D /
M e d i u m or H i g h .
RETURN
Advanced
Gamma
G
V Low
Medium
High
G
V Off
On
Film Mode
E button to select
Low,
Black Level
DE F G
ADVANCED - Film Mode
To set up for the best picture quality for viewing films.
This feature operates only in TV, AV and Component 480i/576i
mode.
RETURN
Advanced
Gamma
Film Mode
1
Press the
M o d e.
G
button and then D /
E
button to select F i l m
2
Press the
Off.
G
button and then D /
E
button to select O n or
Black Level
DE F G
RETURN
ADVANCED - BLACK(DARKNESS) LEVEL
When you view a film this function adjust the set to best picture quality. Adjusting the contrast and the brightness
of the screen using the black level of the screen.
It is not possible to use this function in RGB-PC/DVI-PC mode.
1
Press the G button and then D /
E
button to select B l a c k L e v e l.
2
Press the G button and then D /
High.
E
button to select L o w or
Advanced
Gamma
Film Mode
A
A
Black Level
G
V Low
High
L o w : The reflection of the screen gets darker.
H i g h : The reflection of the screen gets brighter.
DE F G
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
34
PICTURE CONTROL
PICTURE RESET
Returns to the default factory setting for Picture Mode, Color Temperature, XD, Advanced, Aspect Ratio.
Picture
1
Press the M E N U button and then D /
P i c t u r e menu.
2
Press the G button and then D /
R e s e t.
3
Press the G button to initialize the adjusted value.
E
E
button to select the
button to select P i c t u r e
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
DE F G
G
To Set
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
35
PICTURE CONTROL
SCREEN SETUP FOR PC MODE
Auto Configure (RGB [PC] mode only)
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is
still not correct, your set is functioning properly but needs further adjustment.
Auto configure
This function is for automatic adjustment of the screen position, clock, and phase. The displayed image
will be unstable for a few seconds while the auto configuration is in progress.
1. Using OSD
Picture
1
Press the M E N U button and then use D /
P i c t u r e menu.
2
Press the G button and then use D /
E button to select S c r e e n.
3
Press the G button and then use D /
C o n f i g ..
E button to select A u t o
4
E button to select the
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
DE F G
G
To Set
RETURN
Press the G button to start A u t o C o n f i g..
Screen
• When Auto config. has finished, OK will be shown on screen.
• If the position of the image is still not correct, try Auto adjustment
again.
Auto config.
Manual Config.
Resolution
Reset
G
To Set
• If picture needs to be adjusted again after Auto adjustment in RGB
(PC), you can adjust the M a n u a l C o n f i g ..
DE F G
RETURN
2. Using ENTER(Remocon or control key)
This function is available for RGB signals only.
1
Press the E N T E R
button.
2
Press the E N T E R
button.
Auto Config. (ENTER)
Auto in progress
<1920 x 1080 Resolution>
• If you don’t want Auto Configure, do
not press
ENTER
Auto in progress
For optimal display change
resolution to1920 x 1080
<Others Resolution>
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
36
PICTURE CONTROL
Manual Configure (Adjustment for screen Phase, Clock, Position)
(RGB [PC] mode only)
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase
manually.
To correct the screen size, adjust C l o c k.
It’s not available to use Phase, Clock function in COMPONENT
(480i/480p/576i/576p/720p/1080i/1080p), HDMI (480p/576p/720p/1080i/1080p).
C l o c k This function is to minimize any vertical bars or stripes visible on the screen background the horizontal screen size will also change.
P h a s e This function allows you to remove any horizontal noise and clear or sharpen the image of characters.
1
Press the M E N U button and then use D /
P i c t u r e menu.
2
Press the
G button and then use D / E button to select S c r e e n.
3
Press the
C o n f i g ..
G
4
Press the G button and then use D /
C l o c k, H - P o s i t i o n or V - P o s i t i o n.
5
Press the F /
button and then use D /
E button to select the
E button to select M a n u a l
Picture
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
DE F G
G
To Set
RETURN
E button to select P h a s e,
Screen
G button to make appropriate adjustments.
Auto config.
Manual Config.
Resolution
Reset
DE F G
G
Phase
Clock
H-Position
V-Position
81
50
50
50
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
37
PICTURE CONTROL
Selecting Resolution
To view a normal picture, match the resolution of RGB mode and selection of Resolution.
This function works in the following mode: RGB-PC input mode.
Picture
1
Press the M E N U button and then use D /
P i c t u r e menu.
2
Press the G button and then use D /
3
4
E button to select the
E button to select S c r e e n.
Press the G button and then use D /
Resolution
E button to select
Press the G button and then use D /
desired Resolution.
E button to select the
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
DE F G
G
To Set
G
V 1400 x 1050
1680 x 1050
G
To Set
RETURN
Screen
Auto config.
Manual Config.
Resolution
Reset
DE F G
Initializing (Reset to original factory settings)
Press the G button and then use D /
R e s e t.
2
Press the G button.
Screen
Auto config.
Manual Config.
Resolution
Reset
This function operates in current mode.
To initialize the adjusted value
1
RETURN
E
button to select
DE F G
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
38
SOUND CONTROL
PRESET SOUND SETTINGS-SOUND MODE
You can select your preferred sound setting; SRS TS XT, Clear Voice, Standard, Music, Cinema, Sport or Game and you can
also adjust the frequency of the equalizer.
Sound Mode lets you enjoy the best sound without any Special adjustment as the set the appropriate sound options based
on the Channel content.
S R S T S X T, C l e a r V o i c e, S t a n d a r d, M u s i c, C i n e m a, S p o r t and G a m e are preset for optimum sound quality at the
factory and are not adjustable.
• Press the S O U N D button repeatedly to select the appropriate sound setup.
1
Press the M E N U button and then D /
A u d i o menu.
2
Press the G button and then D /
M o d e.
3
Press the G button and then D / E button to select S R S T S X T,
C l e a r V o i c e, S t a n d a r d, M u s i c, C i n e m a, S p o r t , G a m e or
U s e r.
E
button to select the
E button to select S o u n d
Audio
Sound Mode
Auto Volume
Balance
TV Speaker
DE F G
G
SRS TS XT
Clear Voice
V Standard
Music
Cinema
Sport
Game
User
G
SRS TS XT
Clear Voice
Standard
Music
Cinema
Sport
Game
V User
0
RETURN
SOUND SETTING ADJUSTMENT -USER MODE
Adjusting the audio equalizer.
Audio
1
Press the G button and then D /
2
Press the G button.
3
Select a frequency band by pressing the F / G button.
Set the desired sound level with the D / E button.
E
button to select U s e r.
Sound Mode
Auto Volume
Balance
TV Speaker
DE F G
0
RETURN
User
0.1 0.5 1.5 5.0 10 kHz
DE F G
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
G
G
is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under license from SRS Labs, Inc.
39
SOUND CONTROL
AUTO VOLUME LEVELER
Auto Volume automatically remains on the same level of volume if you change channel.
1
Press the M E N U button and then D /
A u d i o menu.
E
button to select the
2
Press the G button and then D /
V o l u m e.
E button to select A u t o
3
Press the G button and then D /
E
Audio
Sound Mode
Auto Volume
Balance
TV Speaker
G
0
V Off
On
button to select O n or O f f.
DE F G
RETURN
BALANCE
You can adjust the sound balance of the speakers to the preferred levels.
Audio
1
2
Press the G button and then D /
B a l a n c e.
Press the G button and then F /
desired adjustment.
E
G
button to select
button to make
Sound Mode
Auto Volume
Balance
TV Speaker
DE F G
0G
...........
...........
RETURN
TV SPEAKERS ON/OFF SETUP
You can adjust the internal speaker status.
In TV, AV, COMPONENT and HDMI mode, internal speaker audio can be operational even though there is no video signal.
If you wish to use an external hi-fi system, turn off the TV internal speakers.
1
2
Press the G button and then D /
S p e a k e r.
Press the G button and then D /
O n or O f f.
E
E
button to select T V
button to select
Audio
Sound Mode
Auto Volume
Balance
TV Speaker
DE F G
0
G
Off
V On
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
40
TIME SETTING
CLOCK SETUP
You must set the time correctly before using on/off timer function.
If current time setting is erased by a power failure or the set is unplugged, reset the clock.
1
Press the M E N U button and then D /
T i m e menu.
2
Press the G button and then D /
E button to select C l o c k.
3
Press the G button and then D /
E button to set the hour.
4
Press the G button and then D /
E button to set the minute.
E
button to select the
Time
Clock
Off Time
On Time
Sleep Timer
Auto Sleep
DE F G
- - : - - AM
G
RETURN
AUTO ON/OFF TIME SETTING
The Off time function automatically switches the set to standby at a preset time.
Two hours after the set is switched on by the on time function it will automatically switch off unless a button has been
pressed.
Once the on time/off time is set, these functions operate daily at the preset time.
The Off time function overrides the On timer function if both are set to the same time.
Time
1
Press the G button and then D / E button to select
O n/O
O f f T i m e.
O f f T i m e function, select O f f.
• To cancel O n/O
2
Press the G button and then D /
E
button to set the hour.
3
Press the G button and then D /
minutes.
E
button to set the
4
For On Time function only
• C h a n n e l: Press the G button and then D / E button to
select the channel.
• V o l u m e: Press the G button and then D / E button to
adjust volume level at switch-on.
Clock
Off Time
On Time
Sleep Timer
Auto Sleep
DE F G
G
- - : - - AM
Off
G
07:00 AM
Ch
TV
Vol.
Off
RETURN
Time
Clock
Off Time
On Time
Sleep Timer
Auto Sleep
DE F G
2
30
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
41
TIME SETTING
SLEEP TIMER SETTING
You do not have to remember to switch the set off before you go to sleep. The sleep timer automatically switches the set
off after the preset time has elapsed.
Time
1
Press the M E N U button and then D /
T i m e menu.
2
Press the G button and then D /
T i m e r.
E button to select S l e e p
3
Press the G button and then D /
E button to set the minute.
E
button to select the
Clock
Off Time
On Time
Sleep Timer
Auto Sleep
DE F G
G
Off
RETURN
! NOTE
G
When you switch the set off, the set releases the preset sleep timer.
AUTO SHUT-OFF SETTING
If the set is switched on and there is no input signal, it will switch off automatically after 10 minutes.
Time
1
Press the G button and then D /
S l e e p.
E
button to select A u t o
2
Press the G button and then D /
O f f.
E
button to select O n or
Clock
Off Time
On Time
Sleep Timer
Auto Sleep
DE F G
G
V Off
On
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
42
OPTION SETTING
ON-SCREEN MENU LANGUAGE SELECTION
Installation guide menu appears on screen when it is turned on for the first time.
Press the D / E/ F / G button and then, E N T E R button to
select your desired language.
1
* If you want to change Language selection
1
Press the M E N U button and then use D /
select the O P T I O N menu.
2
Press the G button and then use D /
L a n g u a g e.
3
Press the G button and then use D / E/ F / G button to
select your desired language. The menus can be shown on
the screen in the selected language.
4
Press the R E T U R N button.
E
button to
Option
Language
PIP
Key Lock
Caption/Text
Set ID
DDC-CI
Power Indicator
Factory Reset
DE F G
E
G
To Set
RETURN
button to select
! NOTE
you don’t finish set up I n s t a l l a t i o n G u i d e by pressing R E T U R N button or time out of OSD (On Screen Display)
display, it will continuously appear until completing set up whenever the set is turned on.
G If
KEY LOCK
The set can be set so that the remote control is needed to control it.
This feature can be used to prevent unauthorized viewing.
This set is programmed to remember which option it was last set to even if you turn the set off.
Option
1
2
Press the G button and then D /
L o c k.
E
Press the G button and then D /
O f f.
E
button to select K e y
button to select O n or
Language
PIP
Key Lock
Caption/Text
Set ID
DDC-CI
Power Indicator
Factory Reset
DE F G
G
V Off
On
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
! NOTE
O n’, if the set is turned off, press the r / I, I N P U T, C H D / E button on the set or P O W E R,
In K e y L o c k ‘O
I N P U T, C H D / E or NUMBER buttons on the remote control.
G With the K e y L o c k O n, the display ‘K e y L o c k O n’ appears on the screen if any button on the right side of set is
pressed while using the set.
G
43
OPTION SETTING
CAPTION/TEXT
Text services give a wide variety of information on all kind of subjects (ex. captioned program lists, weather forecasts, stock
exchange topics, news for hearing-impaired....) on up to half of the screen. But not all stations offer text services, even though
they might offer captioning. In the event you are receiving a poor signal, an empty black box may appear and disappear,
even when the text mode is selected. This is a normal when receiving a poor signal. This set is programmed to remember
the Caption/Text mode it was last set to, when you turn the power off.
Option
1
Press the M E N U button and then D /
O p t i o n menu.
E button to select the
2
Press the G button and then D /
C a p t i o n / T e x t.
E button to select
3
Press the G button and then D /
M o d e 1 , 2 o r T e x t 1 , 2.
E button to select O f f
or
Language
PIP
Key Lock
Caption/Text
Set ID
DDC-CI
Power Indicator
Factory Reset
DE F G
V Off
Mode1
Mode2
Text1
Text2
G
RETURN
DDC CI(Only RGB, DVI mode)
DDC/CI (Display Data Channel Command Interface) is a communication protocol for communications between
PC and set.
DDC/CI makes it possible to adjust and setup detailed functions on PC instead of the set OSD
Set can be adjusted with PC by connecting communication between PC and set when DDC/CI is ON, and set
cannot be adjusted with PC because communication between PC and set is disconnected when DDC/CI is OFF.
1
Press the G button and then D /
DDC-CI.
E
button to select
2
Press the G button and then D /
or O f f.
E
button to select O n
Option
Language
PIP
Key Lock
Caption/Text
Set ID
DDC-CI
Power Indicator
Factory Reset
DE F G
G
V
Off
On
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
44
OPTION SETTING
POWER INDICATOR
It helps you control LED when power is turned on.
1
Press the M E N U button and then D /
O p t i o n menu.
2
Press the G button and then D /
indicator.
3
Press the G button and then D /
E
button to select the
E button to select P o w e r
E
Option
Language
PIP
Key Lock
Caption/Text
Set ID
DDC-CI
Power Indicator
Factory Reset
G
V
Off
On
button to select O n or O f f.
DE F G
RETURN
FACTORY RESET
Use to quickly reset all the menu options to their original factory preset values.
The function deletes all TV channel.
1
Press the G button and then D /
F a c t o r y R e s e t.
E
button to select
2
Press the G button and then F /
or N o.
G
button to select Y e s
Option
Language
PIP
Key Lock
Caption/Text
Set ID
DDC-CI
Power Indicator
Factory Reset
DE F G
G
To Set
RETURN
Factory Reset
Yes
DE
No
RETURN
• Press the MENU button to close the menu window.
• Press the RETURN button to move to the previous menu screen.
45
APPENDIX
TROUBLESHOOTING
The operation does not work normally.
Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the set.
A Ensure that the batteries are installed with correct polarity (+ to +, - to -).
A Ensure that the correct remote operating mode is set: TV, VCR, etc.
A Install new batteries.
A
The remote control
doesn’t work
Power is suddenly
turned off
Is the sleep timer set?
A Check the power control settings. Power interrupted.
A No broadcast on station tuned with Auto sleep activated.
A
The video function does not work.
Check whether the product is turned on.
Try another channel. The problem may be with the broadcast.
A Is the power cord inserted into wall power outlet?
A Check your antenna direction and/or location.
A Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.
A
A
No picture &No sound
Picture appears slowly
after switching on
A
This is normal, the image is muted during the product startup process. Please
contact your service centre, if the picture has not appeared after five minutes.
Adjust Color in menu option.
A Keep a sufficient distance between the product and the VCR.
A Try another channel. The problem may be with the broadcast.
A Are the video cables installed properly?
A Activate any function to restore the brightness of the picture.
A
No color, poor color,
or poor picture
Horizontal/vertical bars
or picture shaking
A
Check for local interference such as an electrical appliance or power tool.
Station or cable product experiencing problems, tune to another station.
Station signal is weak, reorient antenna to receive weaker station.
A Check for sources of possible interference.
A
Poor reception on
some channels
Lines or streaks
in pictures
46
A
A
Check antenna (Change the direction of the antenna).
APPENDIX
The audio function does not work.
A
Picture OK & No sound
A
A
A
No output from one
of the speakers
Unusual sound from
inside
the product
Press the VOL F / G button.
Sound muted? Press MUTE button.
Try another channel. The problem may be with the broadcast.
Are the audio cables installed properly?
A
Adjust Balance in menu option.
A
A change in ambient humidity or temperature may result in an unusual noise
when the product is turned on or off and does not indicate a problem with
the product.
Only RGB/DVI mode applied
No image is displayed.
Power is on, power indictor is blue but the screen
appears extremely dark.
Does the power indicator look amber?
Does the ‘Out of range’
message appear?
Does the ‘Check signal
cable’ message appear?
A
Adjust brightness and contrast again.
A
If the product is in power saving mode, move the mouse or press any key.
A
The signal from the PC (Video card) is out of the vertical or horizontal
frequency range of the product.
Adjust the frequency range by referring to the Specifications in this user’s guide.
A
The signal cable between PC and product is not connected. Check the signal cable.
Press the ‘INPUT’ button in the remote control to check the input signal.
A
47
APPENDIX
‘Unknown Product’ message appears when the product is connected.
A
Install the product driver, which is provided with the product, or download it
from the web site.
(http://www.lge.com)
A
See if the plug_&_play function is supported by referring to the video card
user’s guide.
Did you install the driver?
After-image appears on the product.
After-image appears when
the product is turned off.
A
If you use a fixed image for a long time, the pixels may be damaged quickly.
Use the screen saver function.
A
Set screen color resolution to more than 24 bits (true color)
Select control Panel-Display-Settings-Color Table menu in Windows.
A
Check the connection status of the signal cable.
A
Several pixels (red, green, white or black color) may appear on the screen,
which can be attributable to the unique characteristics of the LCD panel.
It is not a malfunction of the LCD.
Screen color is abnormal.
Screen has poor color resoluion (16_colors).
Screen color is unstable
or mono color.
Do back spots appear on
the screen?
Only RGB mode applied
The screen image looks abnormal.
A
Is the screen position
wrong?
Do thin lines appear on
the background screen?
Horizontal noise appears
or the characters look
blurred.
48
A
Adjust the Position menu in OSD.
See if the video card resolution and frequency are supported by the product.
If the frequency is out of range, set to the recommended resolution in the
Control Panel-Display-Setting menu.
A
Adjust the Clock menu in OSD.
A
Adjust the Phase menu in OSD.
APPENDIX
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can
enjoy your new set.
Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
1
To keep the dust off your screen for a while, wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dishwashing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the
screen.
2
Make sure the excess water is off the screen, and then let it air-dry before you turn on your set.
Cleaning the Cabinet
A
A
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Please be sure not to use a wet cloth.
Extended Absence
CAUTION
G
If you expect to leave your set dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.
49
APPENDIX
PRODUCT SPECIFICATIONS
<M227WA>
LCD Panel
Video Signal
Screen Type
21.53 inches Wide (546.86 mm) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
Visible diagonal size: 546.86 mm
Pixel Pitch
0.248(H) x 0.248(V) mm
Max. Resolution
1920 X 1080 @60 Hz
Recommended Resolution
1920 X 1080 @60 Hz
Horizontal Frequency
30 - 83 kHz
Vertical Frequency
56 - 75 Hz
Synchronization Type
Separate Sync, Digital
Input Connector
Power
Tilt
S-VIDEO, CVBS, TV, D-Sub Analog, DVI-D, HDMI, PC Audio In, Component
Rated Voltage
AC100-240V~ 50/60 Hz 0.9A
Power Consumption
On Mode
: 45W (typ.)
R G B)
Sleep Mode
1W (R
Off Mode
1W
Tilt Range
-5 ~ 15°
Dimensions (Width x Height x Depth)
Weight
Environmental
conditions
Operating Temperature
10 ~ 35°C
Operating Humidity
20 ~ 80%
Storage Temperature
-10 ~ 60°C
Storage Humidity
■
50
519.8 x 400.5 x 193.2 mm (20.46 x 15.77 x 7.61 inches)
4.7 kg / 10.36 lbs
5 ~ 90%
The specifications shown above may be changed without prior notice for quality improvement.
APPENDIX
PRODUCT SPECIFICATIONS
<M237WA>
LCD Panel
Video Signal
Screen Type
23 inches Wide (584.2 mm) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
Visible diagonal size : 584.2 mm
Pixel Pitch
0.265(H) x 0.265(V) mm
Max. Resolution
1920 X 1080 @60 Hz
Recommended Resolution
1920 X 1080 @60 Hz
Horizontal Frequency
30 - 83 kHz
Vertical Frequency
56 - 75 Hz
Synchronization Type
Separate Sync, Digital
Input Connector
Power
Tilt
S-VIDEO, CVBS, TV, D-Sub Analog, DVI-D, HDMI, PC Audio In, Component
Rated Voltage
AC 100-240V ~ 50/60 Hz 1.0A
Power Consumption
On Mode
: 50W (typ.)
Sleep Mode
1W (RGB)
Off Mode
1W
Tilt Range
-5 ~ 15°
Dimensions (Width x Height x Depth)
Weight
Environmental
conditions
■
560.8 x 427 x 193.2 mm (22.08 x 16.81 x 7.61 inches)
5.6 kg / 12.35 lbs
Operating Temperature
Operating Humidity
10 ~ 35°C
20 ~ 80%
Storage Temperature
Storage Humidity
-10 ~ 60°C
5 ~ 90%
The specifications shown above may be changed without prior notice for quality improvement.
51
APPENDIX
IR CODES
1. How to Connect
A
Connect your wired remote control to the Remote Control port on the set.
2. Remote Control IR Codes
A
Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
Carrier frequency
Tc
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
T1
A
Configuration of frame
1st frame
Lead code
Low custom code
High custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
Repeat frame
Repeat code
A
Tf
Lead code
9 ms
4.5 ms
A
Repeat code
0.55 ms
9 ms
A
2.25 ms
Bit description
Bit ”0”
Bit ”1”
0.56 ms
0.56 ms
2.24 ms
1.12 ms
A
Frame interval: Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
52
APPENDIX
(Hexa)
Code
Function
Note
(Hexa)
Code
Function
Note
79
ARC
R/C Button
60
PIP
R/C Button
0B
INPUT
R/C Button
09
MUTE
R/C Button
08
POWER
R/C Button (Power On/Off)
10 ~ 19 Number Key 0 ~ 9 R/C Button
43
MENU
R/C Button
1A
Q.VIEW
R/C Button
28
RETURN
R/C Button
0A
MTS
R/C Button
03
VOL F
R/C Button
0E
SLEEP
R/C Button
02
VOL G
R/C Button
39
CAPTION
R/C Button
00
CH D
R/C Button
1E
FAV
R/C Button
01
CH E
R/C Button
4D
PICTURE
R/C Button
44
ENTER( )
R/C Button
52
SOUND
R/C Button
0F
TV/PC
R/C Button
53
APPENDIX
EXTERNAL CONTROL THROUGH RS-232C
Connect the RS-232C input jack to an external control device (such as a computer or an A/V control
system) and control the set’s functions externally.
Connect the serial port of the control device to the RS-232C jack on the set back panel.RS-232C
connection cables are not supplied with the set.
RS-232C Setup
N
HDMI IN
RS-232C IN
(CONTROL)
N
Type of Connector; D-Sub 9-Pin Male
No.
Pin Name
1
2
3
4
5
6
7
8
9
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
1
5
6
54
9
APPENDIX
RS-232C Configurations
7-Wire Configurations (Standard RS-232C cable)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
SET
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
3-Wire Configurations(Not standard)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
SET
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Set ID
- Use this function to specify a set ID number.
- Refer to ‘Real Data Mapping 1’. See page 59.
1
Press the M E N U button and then use D /
O p t i o n menu.
2
Press the G button and then use D /
3
Press the G button and then use F / G button to adjust S e t I D
to choose the desired set ID number.
• The adjustment range of SET ID is 1~ 99.
E button to select the
E button to select S e t
I D.
Option
Language
PIP
Key Lock
Caption/Text
Set ID
DDC-CI
Power Indicator
Factory Reset
DE F G
G
1
RETURN
Communication Parameters
Baud rate : 9600 bps (UART)
A Data length : 8 bits
A Parity : None
A
Stop bit : 1 bit
A Communication code : ASCII code
A Use a crossed (reverse) cable.
A
55
APPENDIX
Command Reference List
COMMAND1 COMMAND2
DATA
(Hexadecimal)
01. Power
k
a
00 ~ 01
02. Aspect Ratio
k
c
Refer to p.57
COMMAND1 COMMAND2
DATA
(Hexadecimal)
14. Color Temperature
k
u
Refer to p.58
15. Red Adjustment
k
v
00 ~ 3C
03. Screen Mute
k
d
00 ~ 01
16. Green Adjustment
k
w
00 ~ 3C
04. Volume Mute
k
e
00 ~ 01
17. Blue Adjustment
k
$
00 ~ 3C
05. Volume Control
k
f
00 ~ 64
18. Abnormal Status
k
z
FF
06. Contrast
k
g
00 ~ 64
19. Auto Configure
j
u
01
07. Brightness
k
h
00 ~ 64
20. Equalize
j
v
Refer to p.59
08. Color
k
i
00 ~ 64
21. Tune Command
m
a
Refer to p.59
09. Tint
k
j
00 ~ 64
22. Channel Skip
m
b
00 ~ 01
10. Sharpness
k
k
00 ~ 64
23. Key
m
c
Key Code
11. OSD Select
k
k
l
m
00 ~ 01
24. Input select (Main)
x
b
Refer to p.59
k
t
00 ~ 64
12. Remote Control Lock
/Key Lock Mode
13. Balance
00 ~ 01
Transmission / Receiving Protocol
Transmission
OK Acknowledgement
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command2][ ][Set ID][ ][OK][Data][x]
[Command 1] : First command to control the set.(j,k,m or x)
The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is
data read mode, it indicates present status data. If the data is
data write mode, it returns the data of the PC computer.
[Command 2] : Second command to control the set.
[Set ID] : You can adjust the set ID to choose desired set ID
number in Setup menu. Adjustment range is 1~ 99.
When selecting Set ID ‘0’, every connected set is
controlled. Set ID is indicated as decimal (1~ 99)
on menu and as Hexa decimal (0x0~ 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data.
Transmit ‘FF’ data to read status of comand.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
56
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
Set transmits ACK(acknowledgement) based on this format
when receiving abnormal data form non-viable functions or
communication errors.
[Command 2] : use as command.
[Set ID]: use the small character, if set ID is 10, set will send the ‘0’, ‘a’
[Data]: use the small character, if data is 0xab, set will send the ‘a’, ‘b’.
[NG]: use the large character.
APPENDIX
0 5 . Volume Control (Command: k f)
0 1 . Power (Command: k a)
To control Power On/Off of the set.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
Data 01 : Power On
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
To show Power On/Off.
To adjust volume.
You can also adjust volume with the volume buttons
on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 ~ Max : 64
Refer to ‘Real data mapping 1 ’. See page 59.
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
* If there is the time delay between command and
ack message during power on sequence, It should
be described like “Note: In this model, set will send
the Acknowledge after power on processing completion. There might be a time delay between command and acknowledge.”
06. Contrast (Command: k g)
To adjust screen contrast.
You can also adjust contrast in the Picture menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 ~ Max : 64
02. Aspect Ratio (Command: k c) (Main picture size)
To adjust the screen format. (Main picture format)
You can adjust the screen format using the Aspect
Ratio in the Picture menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01: Normal screen (4:3)
Data 02: Wide screen (16:9)
Data 04: Zoom1
Data 05: Zoom2
Data 09: Just Scan
Refer to ‘Real data mapping 1 ’. See page 59.
Acknowledgement [g][ ][Set ID][ ][OK][Data][x]
0 7 . Brightness (Command: k h)
To adjust screen brightness.
You can also adjust brightness in the Picture menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the RGB-PC, Component or HDMI input, you
select either 16:9 or 4:3 screen aspect ratio.
* Just Scan works in the following mode:
Component (720p/1080i/1080p),
HDMI (720p/1080i/1080p)
Data Min : 00 ~ Max : 64
Refer to ‘Real data mapping 1 ’. See page 59.
Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
08. Color (Command: k i)
0 3 . Screen Mute (Command: k d)
To select screen mute on/off.
To adjust the screen color.
You can also adjust color in the Picture menu.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data 00 : Screen mute off (Picture on)
Data 01 : Screen mute on (Picture off)
Data Min : 00 ~ Max : 64
Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
04. Volume Mute (Command: k e)
Refer to ‘Real data mapping 1 ’. See page 59.
09. Tint (Command: k j)
To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
To adjust the screen tint.
You can also adjust tint in the Picture menu.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data Min : 00 ~ Max : 64
Data 00 : Volume mute on (Volume off)
Data 01 : Volume mute off (Volume on)
Refer to ‘Real data mapping 1 ’. See page 59.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Acknowledgement [j][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]
57
APPENDIX
15. Red Adjustment (Command: k v)
10. Sharpness (Command: k k)
To adjust the screen sharpness.
To adjust red in color temperature.
You can also adjust sharpness in the Picture menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Transmission [k][v][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 3C
Data Min : 00 ~ Max : 64
Refer to ‘Real data mapping 2’. See page 59.
Refer to ‘Real data mapping 1 ’. See page 59.
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]
1 6 . Green Adjustment (Command: k w)
11. OSD Select (Command: k l)
To adjust green in color temperature.
To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission [k][w][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 3C
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00: OSD off
Data 01: OSD on
Refer to ‘Real data mapping 2’. See page 59.
Acknowledgement [w][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [l][ ][Set ID][ ][OK][Data][x]
1 7 . Blue Adjustment (Command: k $)
To adjust blue in color temperature.
12. Remote Control Lock/Key Lock Mode (Command: k m)
Transmission [k][$][ ][Set ID][ ][Data][Cr]
To lock the remote control and the side key
Data Min: 00 ~ Max: 3C
controls on the set.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Refer to ‘Real data mapping 2’. See page 59.
Data 00: Lock off
Acknowledgement [$][ ][Set ID][ ][OK/NG][Data][x]
Data 01: Lock on
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
18. Abnormal Status (Command: k z)
To recognize an abnormal state.
13. Balance (Command: k t)
To adjust balance.
You can also adjust balance in the Audio menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 ~ Max : 64
Refer to ‘Real data mapping 1 ’. See page 59.
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]
14. Color Temperature (Command: k u)
To adjust color temperature.
You can also adjust Color Temperature in the Picture
menu.
Transmission [k][u][ ][Set ID][ ][Data][Cr]
Data 00: Medium 01: Cool 02: Warm(Don’t operate in RGB, DVI mode)
Data 05: 9300K 06: 6500K 07: sRGB(Operate in RGB, DVI mode)
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
58
Transmission [k][z][ ][Set ID][ ][FF][ ][Cr]
Data FF: Read
Acknowledgement [z][ ][Set ID][ ][OK/NG][Data][x]
Data 00: Normal (Power on and signal exist)
Data 01: No signal (Power on)
Data 02: Turn the set off by remote control
Data 03: Turn the set off by sleep time function
Data 04: Turn the set off by RS-232C function
Data 05: 5V down
Data 06: AC down
Data 07: Turn the set off by Fan Alarm function (option)
Data 08: Turn the set off by Off time function
Data 09: Turn the set off by Auto off function
Data a: Turn the set off by AV board detection.
* This function is “read only”.
APPENDIX
22. Channel Skip(Command: m b)
19 . Auto Configure (Command: j u)
To adjust picture position and minimize image
G To set skip status for the current channel.
shaking automatically. It works only in RGB (PC)
mode.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 00 : Skip
01 : Add
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
Data 01: To set
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
2 0 . E q u a l i z e (C o m m a n d : j v )
23. K e y C o d e (Command: m c)
To send IR remote key code.
G To adjust equalize.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
0
LSB
0
0
0
0
0
Frequency
0
0
Data
Data: Key code - Refer to page 53.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
24. Input select (Command: x b)
(Main Picture Input)
To select input source for set
7
6
5
Frequency
4
3
2
1
0
Step
0
0
0
1’st Band
0
0
0
0
0
0(decimal)
0
0
1
2’nd Band
0
0
0
0
1
1(decimal)
Data: Structure
0
1
0
3’rd Band
0
0
0
1
0
2(decimal)
MSB
0
1
1
4’th Band
1
0
0
5’th Band
...
0
1
1
1
1 15(decimal)
Transmission [x][b][ ][Set ID][ ][Data][Cr]
LSB
0
0
0
External Input
0
0
0
0
0
Input Number
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
* Real data mapping 1
00 : Step 0
* Real data mapping 2
00: -8
01: -7
A : Step 10
08: 0
F : Step 15
0E: +6
0F : +7
21 . Tune Command / Channel Tuning (Command: m a)
Input
command
TV
[x][b][ ][Set ID][ ][10][Cr]
AV
[x][b][ ][Set ID][ ][20][Cr]
Component
[x][b][ ][Set ID][ ][40][Cr]
RGB
[x][b][ ][Set ID][ ][60][Cr]
DVI
[x][b][ ][Set ID][ ][80][Cr]
HDMI1
[x][b][ ][Set ID][ ][90][Cr]
HDMI2
[x][b][ ][Set ID][ ][91][Cr]
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
Tune Channel to following Physical number.
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1]
[ ][Data2][Cr]
Data00 02~45 (TV), 01(CATV), 0E~7D(CATV)
(*transmit by Hexadecimal code)
Data01 don’t care
Data02 0 : TV
1 : CATV
Acknowledgement [a][ ][Set ID][OK][ ][Data0][Data1][Data2][x]
[a][ ][Set ID][NG][ ][Data0][x]
59
Download PDF

advertising