LG | T530SAK | LG T530SAK Owner’s Manual

Precautions
Important
This unit has been
engineered and manufactured to ensure your personal
safety, however improper use may result in potential eletrical shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this monitor, observe the following basic rules for its
installation, use, and servicing. Keep it in an accessible place for future
reference.
On
Use
Safety
with the unit. In
only the power cord supplied
case
you
use
another power
by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.
cord, make
sure
that it is certified
The power supply cord is used as the main disconnect device. Ensure that the
socket-outlet is easily accessible after installation.
a power source indicated in the specifications of
the monitor. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Operate the
this manual
monitor
or
listed
only from
on
Overloaded AC outlets and extension cords
cords and broken
technician for
plugs. They may
replacement.
Hands must be
Do not
It
are
a
the power
dangerous. So
shock
plug
or
are frayed power
fire hazard. Call your service
to avoid an electric shock.
damage the power cord by disassembling, bending, pulling
can cause
Make
dry when holding
result in
sure
fire
to
or
or
heating up.
electric shock.
completely
insert the power
plug.
Insecure connections
can cause
fire.
Do not
Open
the Monitor.
There
are no user
There
are
serviceable components inside.
Dangerous High Voltages inside, even when the power
Contact your dealer if the monitor is not operating properly.
To Avoid Personal
place the
only a stand
Injury
:
Do not
monitor
Use
recommended
Do not try to roll
carpets.
a
is OFF.
sloping shelf unless properly secured.
by the manufacturer.
small casters across thresholds or deep pile
on a
stand with
A1
To Prevent Fire
or
Hazards:
the monitor OFF if you leave the room for more than
of time. Never leave the monitor ON when leaving the house.
Always turn
a
short
period
Keep children from dropping or pushing objects into the monitor's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this monitor.
During a lightning storm or when the monitor is to be left unattended for an
extended period of time, unplug it from the wall outlet.
Do not bring magnetic devices such as magnets or motors near the picture
tube.
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not
the monitor where the power cord is subject to damage.
Do not
use
this monitor
sink, laundry tub, in
near
wet
water such as near a
basement,
place
bathtub, washbowl, kitchen
swimming pool.
Monitors are provided with ventilation openings in the cabinet to allow the
of heat generated during operation. If these openings are blocked, built-up
a
or near a
release
heat
failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the monitor on a bed, sofa, rug,
can cause
etc.
Place the monitor in
Cover the
a
built-in enclosure unless proper ventilation is
cloth or other material.
Place the monitor
near or over a
Do not install the monitor in
On
a
radiator
dusty
or
area.
It
heat
source.
can cause
fire.
Cleaning
Unplug the monitor before cleaning
Use a slightly damp (not wet) cloth.
monitor
On
provided.
openings with
screen
the face of the monitor
Do not
because overspray may
use an
cause
aerosol
screen.
directly
on
the
electrical shock.
Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
Connecting
the Monitor
Before
setting up the monitor, ensure that the power is turned off to the
monitor, computer system, and other attached devices.
Carefully set the monitor face-down with the underside facing you.
Connecting the Tilt/Swivel stand
1. Align the hooks on the tilt/swivel stand with the matching slots in the base of
the monitor.
2.
3.
Insert the hooks into slots.
Slide the tilt/swivel stand toward the front of the monitor until the latches click
into the locked
position.
NOTE
This illustration depicts the general model of connection. Your monitor may differ from the
items shown in the picture.
Slot
Hook
Latch
AA3
Hook
Connecting
the Monitor
Using the Computer
1. Connect the signal cable. When mated, tighten the thumbscrews to secure the
connection.
2. Connect the power cord into a properly power outlet that is easily accessible and
close to the monitor.
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your monitor
may differ from the view as shown.
Signal Cable
Power Cord
*
Attached Type
Wall-outlet
type*
Detached
*
Type
*
Varies according to model.
PC-outlet
type*
PC
MAC
Mac adapter
For Apple Macintosh use, a separate plug adapter is needed to
change the 15 pin high density (3 row) D-sub VGA connector
on the supplied cable to a 15 pin 2 row connector.
A4
Control Panel Functions
Front Panel Controls
Control
Function
Power Button
Use this button to turn the monitor
Power
This Indicator
(DPMS)
lights
on or
off.
up green when the monitor
Indicator
operates normally. If the monitor is in DPM
(Energy Saving) mode, this indicator will flicker.
MENU
Use this button to enter
(or OSD)
Button
exit the
on screen
display.
Buttons
Use these buttons to choose
the
SELECT
(or SET)
or
on screen
Use this button to enter
Button
screen
display.
A5
or
adjust
items in
display.
a
selection in the
on
Control Panel Functions
Front Panel Controls
Control
Direct Access Function
Button
Bring
up Contrast
Button
Bring
up
The Contrast and
On Screen
adjustment
Brightness adjustment
Brightness functions are
Display (OSD) menu.
also available in the
CONTROLS LOCKED/UNLOCKED
:
CONTROLS LOCKED
CONTROLS UNLOCKED
MENU and
This function allows you to secure the current
control settings, so that they cannot be
inadvertently changed. Press and hold the MENU
button and
button for 5 seconds: the message
"CONTROLS LOCKED" appears.
unlock the OSD controls at any time by
the MENU button and
button for 5
seconds:
The message "CONTROLS UNLOCKED" will
You
can
pushing
appear.
A6
On Screen
Screen
Display (OSD) Control Adjustment
Adjustment
Making adjustments to the image size, position and operating parameters of
the monitor is quick and easy with the On Screen Display Control system. A
short example is quick and easy given below to familiarize you with the use of
the controls. The following section is an outline of the available adjustments
and selections you can make using the OSD.
NOTE
Allow the monitor to stabilize for at least 30 minutes before
To make
adjustments
in the On Screen
Display,
making image adjustments.
follow these steps:
Case 1
Case 2
Press the MENU (or OSD) Button, then the main
menu
of the OSD
appears.
To
access a
becomes
control,
Use the
Accept
use
the
highlighted, press
the
Buttons to
changes by pressing
Exit the OSD
by Pressing
Buttons. When the icon you want
or
the SELECT (or SET) Button.
adjust
the item to the desired level.
the SELECT (or SET) Button.
the MENU (or OSD) Button.
A7
On Screen
The
and
Display(OSD) Selection
and
Adjustment
following table indicates all the On Screen Display control, adjustment,
setting menus.
Main
Sub
menu
BRIGHTNESS/
CONTRAST
POSITION
SIZE
Reference
menu
Brightness
To
Contrast
contrast of the
V Position
To
H Position
screen
V Size
To
adjust the
To
adjust the shape
and
screen
adjust the position
of the
size of the
screen
H Size
Tilt*
SHAPE
adjust the brightness
of the
screen
Side Pincushion
S Pincushion Balance
Parallelogram
Trapezoid
H Corner
Top Corner
Bottom Corner
PRESET 6500K
To customize the color of the
9300K
COLOR
screen
Temp
R/G/B(User Color)
SETUP
Video Level
To customize the
Language
for
a
user's
screen
operating
status
environment
OSD Time
Degauss
SPECIAL
To
improve the clarity
stability of the screen
Recall
Reset
Moire
H Moire
V Moire
Convergence
Purity
:
A8
Adjustable
and
On Screen
You
were
Display(OSD) Selection
introduced to the
and
Adjustment
procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
NOTE
The order of icons may differ
To
depending
adjust the brightness and
OSD
on
the model
(A9~A12).
contrast of the
Adjust
screen
Description
Brightness
adjust the brightness of the screen.
To
Contrast
To adjust the contrast of the
To
adjust the position of the
OSD
screen.
screen
Adjust
Description
Vertical Position
To move image up and down.
Horizontal Position
To move image left and
A9
right.
On Screen
To
Display(OSD) Selection
adjust the
OSD
size of the
and
Adjustment
screen
Adjust
Description
Vertical Size
To
adjust image height.
Horizontal Size
To
To
adjust the shape of the
OSD
adjust image width.
screen
Adjust
Description
Tilt*
To correct
image
rotation.
Side Pincushion
To correct
the
a concave or convex
bowing
of
image.
Side Pincushion Balance
To correct the balance of both sides
bowing.
Parallelogram
correctly adjust the skew of the image.
To
Trapezoid
To correct
H
geometric distortion.
Corner*
Top Corner*
Bottom
Corner*
To correct
*
an irregular distortion
displayed image.
This function is available for
models only.
designated
8
A10
of the
On Screen
Display(OSD) Selection
To customize the color of the
OSD
and
Adjustment
screen
Adjust
Description
PRESET
6500K/ 9300K
Select the screen color.
6500K: Slightly reddish white.
9300K: Slightly bluish white.
?
?
Select the
TEMP
screen
prefer among
temperature which you
reddish
or
bluish
or
any color
in between.
RED
GREEN
BLUE
To customize the
OSD
screen
status for
a
Adjust
Set your
user's
own
color levels.
operating environment
Description
VIDEO LEVEL This item is used to select the monitor's
input signal level. The normal level used for
most PCs is 0.7V.
If the screen becomes suddenly washedout or blurred, please select 1.0V and try
again.
LANGUAGE To choose the language in which the
control names are displayed.
OSD Menus are available in 12 languages:
English, German, French, Spanish, Italian,
Swedish, Finnish, Portuguese, Korean,
Chinese, Russian and Polish.
OSD TIME
A11
Set the OSD time, i.e. the length of time a
menu will remain on-screen before it shuts
off automatically. Adjust the time to 5, 10,
20, 30 or 60 seconds.
On Screen
To
Display(OSD) Selection
improve
OSD
the
clarity
and
and
stability
Adjust
Adjustment
of the
screen
Description
DEGAUSS To manually demagnetize the screen to
avoid showing incorrect images or colors.
RECALL
You can use this function to reload the
modified parameters for screen display
operation, as specified by the user after
purchase: Position, Size, Side Pincushion,
Trapezoid (These recalled options may differ
depending on the
User, or New).
mode selected: Preset,
If you don't want to recall the monitor to
these modified settings, use the
button
to select CANCEL and then press the
SELECT (or SET) button.
H
RESET
Return to all factory default settings
If you don't want to reset the monitor,
use
the
button to select CANCEL and then
press the SELECT (or SET) button.
MOIRE
This item allows you to reduce the degree of
moire. (Moire is caused by interference
Horizontal Scan Line with the periodical dot
screen). It is normally OFF(H:0/V:0).
The moire adjustments may affect the focus
of the screen.
Moire adjustments may shake slightly while
the moire reduction function is on.
CONVER- This is to adjust the
and blue fields.
GENCE*
PURITY*
Use to
adjust
the
purity
if the color appears
*
This function is available for
models only.
designated
8
A12
alignment
on
the
uneven.
of red
screen
Troubleshooting
Check the
No
following before calling for service.
image
appears
Is the power cord of the
monitor connected?
Is the power indicator light
on?
Is the power on and the
power indicator green?
Is the power indicator
?
?
Press the Power button.
?
Adjust the brightness and the contrast.
?
If the monitor is in power saving mode, try moving the
pressing any key on the keyboard to bring up
the screen.
flickering?
mouse or
Doyouseean"OUTOF
?
FREQUENCY" message
on the screen?
Doyouseea"SELF
?
DIAGNOSITICS" message
on the screen?
The
screen
Check and see if the power cord is connected properly to
the power outlet.
is
This message appears when the signal from the PC
(video card) is out of horizontal or vertical frequency range
of the monitor. See the 'Specifications' section of this
manual and configure your monitor again.
This message appears when the signal cable between
your PC and your monitor is not connected. Check the
signal cable and try again.
flickering.
Is the vertical frequency
less than 70Hz or is your
monitor set to the
interlaced mode?
Do you have any
magnetic material such
?
?
adapter, or highvoltage line near to your
Set the vertical frequency to 72Hz or higher, and
consult the video card user manual for instructions on
converting to a non-interlaced mode.
(You can set this option under the Display icon of the
Control Panel.)
Remove magnetic sources, such as power adapters,
speakers, or high-voltage lines, away from the
monitor.
as
monitor?
Do you hear a "~ding"
sound while the monitor
is flickering?
?
Use the normal degaussing function. This function
clears the screen and reduces any screen blur that
may occur due to the surrounding magnetic field. The
screen may flicker for about 5 seconds, accompanied
by a "~ding"sound.
A13
Troubleshooting
The
screen
color is not normal.
Do you see basic
discoloration (16 colors)?
?
Is the screen color
unstable or monochrome?
Do you see black dots on
the screen?
?
Set the color depth to 256 colors or higher: use 'Control
Panel' ->'Display' ->'Settings' ->'Color Palette'
Check the connection of the signal cable. Or pull out the
video card of the PC and insert it again.
?
This is due to a small amount of foreign or abnormally
florescent material that became fastened on the mask
during manufacturing. It will not affect product
?
This happens due to interference from surrounding
magnetic fields, as created when speakers, steel
structures, or high-voltage lines are placed near the
monitor. Remove any such materials from the immediate
vicinity and use the DEGAUSS icon on the screen
adjustment menu to fix the screen.
performance.
Do you see a partial
blurring on the screen?
I
see an
after-image
Do you see the afterimage even when you
turn off the monitor?
I
see waves on
the
Do you see the wave
directly on the screen?
on
?
the
screen.
A premature aging of the monitor pixels may cause the
prolonged display of a single image on the screen. Be
sure to use a screen saver to maximize the service life of
the monitor.
screen.
?
This occurs in inverse proportion to the screen focus,
which can be caused by a particular frequency or video
card. Brighten the screen and use the 'MOIRE' icon on
the screen adjustment menu to adjust the screen.
Have you installed the monitor driver?
Have you installed the
monitor driver?
?
Be sure to install the monitor driver from the monitor driver
CD (or diskette) that comes with your monitor. Or, you
can also download the driver from our web site:
http://www.lge.com.
A14
Specifications
Picture Tube
15 inches (13.8 inches viewable)
90
degree deflection
pitch
0.28mm dot
AGARAS(Anti-Glare Anti-Reflective Anti-Static) coating
Sync Input
Video Input
Resolution
Plug&Play
Horizontal
Freq.
Vertical Freq.
Input Form
Signal Input
30
Input Form
Separate, RGB Analog, 0.7Vp-p/75 ohm,
Max
VESA 1024
Recommend
VESA 800
Consumption
-
56kHz (Automatic)
120Hz (Automatic)
Separate TTL, Positive/Negative
15 pin D-Sub Connector
x
x
768 @ 70Hz
600 @ 85Hz
DDC 2B
63W
On
Power
50
-
≤4W
Sleep
Off
≤4W
Width
35.6
cm
&Weight
(with tilt/ swivel
stand)
Height
Depth
37.1
cm
39.5
cm
Net
11.5
kg (25.3 lbs)
Power
AC 100-240V 50/60Hz 1.5A
Dimensions
Input
Environmental
Conditions
/ 14.0 inches
/ 14.6 inches
/ 15.5 inches
Operating Conditions
Temperature
Humidity
10˚C to 40 ˚C
10 % to 80 %
non-Condensing
Storage Conditions
-20˚C to 60 ˚C
Temperature
10 % to 90 % non-Condensing
Humidity
Tilt/Swivel Stand
Signal
cable
Power cord
Attached(
), Detached ( O )
Attached( O ), Detached (
Wall-out type
or
)
PC-outlet type
NOTE
Information in this document is
subject to change without
A15
notice.
Positive
Preset Modes
(Resolution)
1
VESA
640
x
480
37.50
75
2
VESA
640
x
480
31.47
60
3
VESA
800
x
600
53.674
85
4
VESA
1024
48.363
60
x
768
Download PDF

advertising