LG | 29FE5RGE-TG | LG 21FD2RGQ-TG Owner’s Manual

Chassis : CW62A/D/E
P/NO : MFL39623301(REV. 08)
3
Important Precautions
Safety/Installation
5
8
/ Auto Demonstration
9
10
Auto programme scan
Assigning a station name / Booster (option)
Favourite Programme / Calling Programme table
15
PSM (Picture Status Memory) / Picture Adjustment
Eye (option) / Turbo Picture Selection (option)
17
SSM (Sound Status Memory) / Sound Adjustment
Turbo Sound Selection (option) / Sound output selection (option)
Stereo / Dual Reception / NICAM Reception (option)
20
21
/ Games (option)
24
S- Video/Audio in sockets (S-AV) (option)
Headphone socket (option)
26
2
Important Precautions
This unit has been engineered and manufactured to assure your personal safety, however
improper use may result in potential electrical shock or fire hazards. In order to allow the proper
operation of all safeguards incorporated in this TV set, observe the following basic rules for its
installation, use and servicing. Keep it in an accessible place for future reference.
On Safety
The power supply cord is used as the main disconnect device. Ensure that the socket-outlet
is easily accessible after installation.
Operate the TV set only from a power source indicated in the specifications of this manual or
listed on the TV set. If you are not sure what type of power supply you have in your home,
consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed power cords and
broken plugs. They may result in a shock or fire hazard. Call your service technician for
replacement.
Hands must be dry when holding the power plug to avoid an electric shock.
Do not damage the power cord by disassembling, bending, pulling or heating up, it can cause
fire or electric shock.
Make sure to completely insert the power plug. Insecure connections can cause fire.
Do not Open the TV set
There are no user serviceable components inside.
There are Dangerous High Voltages inside, even when the power is Off.
Contact your dealer if the TV is not operating properly.
To Avoid Personal Injury :
Do not place the TV set on a sloping shelf unless properly secured.
Use only fixed wooden stand. The TV shall be positioned 5cm behind the front
edge of an open fronted with 1cm free space along the sides top and 5cm
depth behind the TV.
Do not try to roll a stand with small casters across thresholds or deep pile
carpets.
To Prevent Fire or Hazards:
Always turn the TV set Off if you leave the room for more than a short period
of time. Never leave the TV set On when leaving the house.
Keep children from dropping or pushing objects into the TV cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this TV set.
During a lighting storm or when the TV set is to be left unattended for an
extended period of time, unplug it from the wall outlet and external socket.
Do not bring magnetic devices such as magnets or motors near the picture tube.
3
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the TV set
where the power cord is subject to damage.
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back
cover. Never apply DC power to the set. In the event of thunderstorms or powercuts, please
pull out the aerial and mains plugs.
Service
Do not attempt to service the TV set yourself, as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Aerial
Connect the aerial cable to the socket marked 75
on the back cover. For the best reception
an outdoor aerial should be used.
Location
Do not use this TV near water such as near bathtub, washbowl, kitchen sink, laundary tub,
in a wet basement, or near a swimming pool.
TV set are provided with ventilation openings in the cabinet to allow the release of heat
generated during operation. If these openings are blocked, built-up heat can cause failures
which may result in a fire hazard. There fore,
The ventilation should not be impeded by covering the ventilation openings with items such as
newspaper, table cloths, curtains, etc.
Never place the TV set in a built-in enclosure unless proper ventilation is provided.
No naked flame source such as lighted candles should be placed on the TV.
Never place the TV set near or over a radiator or heat source.
Position your set so that no bright light or sunlight falls directly onto the screen.
On Cleaning
Unplug the TV set before cleaning the face of the TV screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the TV screen because
overspray may cause electric shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal container in which to
transport the unit. When shipping the unit to another location, repack it in its original material.
Caution: Please do not use stabilizer with TV set as this set has inbuilt voltage
stabilizer. Use of Inferior quality stabilizer may damage the set.
Battery installation
The remote control handset is powered by two AA/AAA type batteries. To load the batteries, turn the remote
control handset over and open the battery compartment. Install two batteries as indicated by the polarity
symbols ( + and ) marked inside the compartment.
Note: To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the
remote control handset for an extended period of time.
4
MUTE
POWER
1
9
1
2
8
2
3
4
5
6
Remote control handset
7
8
9
Before you use the remote control handset, please install the batteries.See the next page.
PSM
0
SSM
15
VOL
PR
MENU
VOL
OK
12
PR
14
10
16
3
6
11
SLEEP
5
EYE/*
LIST
TV/AV
ARC/* Q. VIEW
13
FAVOURITE
SOUND
PICTURE
TURBO
XD
18
17
I/II/*
19
7
(Option 1)
MUTE
POWER
1
9
1
2
8
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the front
panel of the set.
2
3
4
5
6
7
8
9
PSM
0
SSM
1. POWER
switches the set on from standby or off to standby.
2. NUMBER BUTTONS
switches the set on from standby or directly select a channel
number.
3. ARC/* (Aspect Ratio Control) (Option)
changes the picture format.
4. TURBO PICTURE / SOUND BUTTON (option)
selects Turbo picture / sound.
5.
/ (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
/
(Volume Up/Down)
adjusts the volume.
adjusts menu settings.
6. SSM (Sound Status Memory)
recalls your preferred sound setting.
7. I/II/* (option)
selects the language during dual language broadcast (option).
selects the sound output.
6
8. PSM (Picture Status Memory)
recalls your preferred picture setting.
15
11
SLEEP
5
VOL
PR
MENU
VOL
OK
12
PR
14
10
16
3
9. MUTE
switches the sound on or off.
EYE/*
LIST
TV/AV
ARC/* Q. VIEW
10.TV/AV
selects TV or AV mode.
switches the set on from standby.
13
FAVOURITE
SOUND
PICTURE
4
17
TURBO
11.MENU
selects a menu.
I/II
7
12.OK
accepts your selection or displays the current mode.
(Option 2)
5
13. LIST
displays the programme table.
14. EYE/*(option)
switches the eye function on or off.
1
POWER
MUTE
TV/AV
9
10
15. SLEEP
sets the sleep timer.
16. Q.VIEW
returns to the previously viewed programme.
1
2
3
4
5
6
7
8
9
17. FAVOURITE
selects a favorite programme.
2
0
11
MENU
14
19. TURBO SOUND/* (option)
selects excellent digital surround.
EYE/*
PR
12
5
18. XDP/* (option)
Select Excellent Digital Picture.
VOL
OK
Battery installation
VOL
The remote control handset is powered by two AA type batteries.
To load the batteries, turn the remote control handset over and
openthe battery compartment. Install two batteries as indicated by
the polarity symbols ( and ) marked inside the compartment.
PR
16
ARC/*
Q-VIEW
LIST
3
13
FAVOURITE TURBO SOUND/*
XDP/*
18
17
PSM
8
15
SLEEP
SSM
I/II/*
(Option 3)
6
19
7
Note : To avoid damage from possible battery leakage, remove
the batteries if you do not plan to use the remote control handset
for an extended period of time.
6
FRONT PANEL / SIDE PANEL (Option)
Shown below is a simplified representation of front or side panel, here shown may be somewhat different from your set.
Common
On Off
8
7
On or Off.
AV3
S VIDEO
MENU
ON/OFF
VIDEO L/MONO AUDIO R
6
1
OK
PR
VOL
2 5 3
4
9
29FC8 series / 29FE5 series
On.
S VIDEO
VIDEO L/MONO AUDIO R
8
7
6
MENU
ON/OFF
1 25
AV3
OK
VOL
3
PR
9
4
3
29FD7/29FU8 series
AV3
4
VIDEO L/MONO AUDIO R
6
S VIDEO
8
7
1
2 5
29FD5 series
MENU
AV3
PR
VOL
1
3
9
2 5
4
On
29FU3 series
R AUDIO
6
OK
ON/OFF
VIDEO L/MONO AUDIO R
6
S VIDEO
8
7
3
4
9
4
L/MONO
ON/OFF
VIDEO
5
AV IN 3
29FU6 series
2
5
2
5
3
AV3
6
(Option)
1
1
21FU6 series
4
10
3
6
21FU8 series
4
8
1
2 6
7. S-VIDEO/AUDIOINSOCKET(S-AV)(Option)
Connect the video out socket of an
S-VIDEO VCR to the S-VIDEO socket.
Connect the audio out sockets of the
S-VIDEO VCR to the audio sockets as in AV-2.
8. HEADPHONE SOCKET(Option)
Connect the headphone plug to this socket.
9
21SA1 series
3
9.
VIDEO
L
AUDIO
R
6
AV2
4
1
2 5
21SA2 series
2 5
R AUDIO L/MONO
3
VIDEO
6
4
1
SWIVEL STAND
This feature is available with 21SA1model only.
After installing the TV, you can adjust the TV set
manually to the left or right direction by 15 degrees
to suit your viewing position.
7
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
Note: In some model yellow key will work as quickview.
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
8
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
Station
SSM
6
SLEEP
VOL
PR
OK
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
Move
9
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
10
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
6
MUTE
POWER
PR
OK
SSM
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
XD
I/II/*
11
Fine tuning
Normally fine tuning is only necessary if reception is poor.
1. Repeat the Manual programme tuning steps 1 to 3.
2. Press the
button to select Fine.
3. Press the
button step by step to fine tune for the best
picture and sound.
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
4. Press the OK button.
5. Repeatedly press the MENU or button to return to normal TV
viewing.
The Fine tuned programme will be indicated by yellow number
during programme selection.
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
12
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
13
Station
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SSM
c. In some model blue key will work as list.
SLEEP
VOL
PR
OK
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
14
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
90
15
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
VOL
Turbo picture or XD picture selection (Option)
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
Note:
a. If you press the PSM or TURBO PICTURE / XD PICTURE
button with the eye function, the function is automatically
switch off.
b. EYE function is not available for RGB input source.
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
XD Off
XD On
(TURBO PICTURE/ XD PICTURE OFF)
(TURBO PICTURE/ XD PICTURE ON)
Note:
a. TURBO PICTURE/XD PICTURE function is not available for RGB
input source.
16
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
EYE/*
LIST
Sports
FAVOURITE
SOUND
PICTURE
TURBO
I/II/*
XD
Sports
Sports.
17
Turbo
Sound
Turbo Sound
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
Turbo Sound Off
EYE/*
LIST
SOUND
PICTURE
TURBO
XD
I/II/*
18
Turbo Sound On
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
19
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
20
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
21
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
22
MUTE
POWER
1
2
3
4
5
6
7
8
9
PSM
0
SLEEP
VOL
PR
OK
SSM
MENU
VOL
PR
TV/AV
ARC/* Q. VIEW
FAVOURITE
EYE/*
LIST
SOUND
PICTURE
TURBO
I/II/*
XD
23
OUT
IN
24
S-Video/ Audio in sockets (S-AV) (option)
When connecting an S-VIDEO VCR to S-VIDEO socket, the picture
quality will be further improved.
S-VIDEO VCR
B VIDEO
1. Connect the S-video socket of the VCR to the S-VIDEO socket of
the set.
2. Connect the audio cable from the S-VIDEO VCR to the AUDIO
socket of set.
3. Select S-VIDEO by pressing th TV/AV button repeatedly.
4. Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
VIDEO L/MONO AUDIO R
AV3
S-VIDEO VCR
Headphone socket (option)
Only models which have a headphone socket can perform this
function.
Insert the headphone plug to the headphone socket of the set. You
can listen to the sound through the headphone.
B VIDEO
If you press the MUTE button, the sound from the headphone is
switched Off.
VIDEO L/MONO AUDIO R
AV3
25
On
On
Note:
i) Colour patch might appear in your TV set if you rotate or shift the position of the set while it is On or in
standby mode. If patch appears in your TV set try the following before calling your service centre or
dealer. Place the TV set in desired position and switch it Off by the main power switch. Allow the set to
cool down for at least 30 minutes and then switch it On. The degaussing circuit (inbuilt) in your set will
remove the patch automatically. Please call service only in case this operation does not help.
ii) When the TV set is switched Off in Standby mode, It may take some time (upto 15 second) for the LED
to switch Off.
26
Download PDF

advertising