LG | 24LH452A | LG 24LH452A Owner’s Manual

OWNER’S MANUAL
Safety and Reference
LED TV*
* Disclaimer
LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and
retain it for future reference.
www.lg.com
MFL69446103
P/NO : MFL69 (160-REV00)
ENGLISH
2
Safety instructions
WARNING
CAUTION
If you ignore the caution message, you may be slightly injured or
the product may be damaged.
ENGLISH
If you ignore the warning message, you may be seriously injured or
there is a possibility of accident or death.
Make sure to connect Mains cable to compliant AC mains socket with
Grounded earth pin. (Except for devices which are not grounded on
earth.) Otherwise possibility you may be electrocuted or injured.
Please read these safety precautions carefully before using the product.
WARNING
Insert power cable plug completely into wall socket otherwise if not
secured completely into socket, fire ignition may break out.
Do not place the TV and/or remote control in the following
environments:
• A location exposed to direct sunlight
• An area with high humidity such as a bathroom
• Near any heat source such as stoves and other devices that
produce heat
• Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil
• An area exposed to rain or wind
• Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or product
deformation.
Ensure the power cord does not come into contact with hot objects
such as a heater. This may cause a fire or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in fire or electric shock.
Do not place the product where it might be exposed to dust. This may
cause a fire hazard.
Bend antenna cable between inside and outside building to prevent
rain from flowing in. This may cause water damaged inside the Product
and could give an electric shock.
Mains Plug is the TV connecting/disconnecting device to AC mains
electric supply. This plug must remain readily attached and operable
when TV is in use.
When mounting TV onto wall make sure to neatly install and isolate
cabling from rear of TV as to not create possibility of electric shock /
fire hazard.
Do not touch the power plug with wet hands. Additionally, if the cord
pin is wet or covered with dust, dry the power plug completely or wipe
dust off. You may be electrocuted due to excess moisture.
Do not plug too many electrical devices into a single multiple electrical
outlet. Otherwise, this may result in fire due to over-heating.
3
ENGLISH
Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the product.
Des
Do not drop metallic objects such as coins, hair pins, chopsticks or wire
into the product, or inflammable objects such as paper and matches.
Children must pay particular attention. Electrical shock, fire or injury
can occur. If a foreign object is dropped into the product, unplug the
power cord and contact the service centre.
icca
nt
Keep the anti-moisture packing material or vinyl packing out of the
reach of children. Anti-moisture material is harmful if swallowed. If
swallowed by mistake, force the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause suffocation. Keep it out
of the reach of children.
Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child does not
consume them. Please seek Doctor- Medical Attention immediately if
child consumes batteries.
Do not insert any metal objects/conductors (like a metal chopstick/
cutlery/screwdriver) between power cable plug and input Wall Socket
while it is connected to the input terminal on the wall. Additionally,
do not touch the power cable right after plugging into the wall input
terminal. You may be electrocuted. (Depending on model)
Do not put or store inflammable substances near the product. There is a
danger of combustion/explosion or fire due to careless handling of the
inflammable substances.
4
Do not spray water on the product or scrub with an inflammable
substance (thinner or benzene). Fire or electric shock accident can
occur.
Do not allow any impact, shock or any objects to fall into the unit,
and do not drop anything onto the screen. You may be injured or the
product can be damaged.
Never touch this product or antenna during a thunder or lighting storm.
You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the
windows and ventilate. It may cause a fire or a burn by a spark.
Do not disassemble, repair or modify the product at your own
discretion. Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
• The product has been impacted by shock
• The product has been damaged
• Foreign objects have entered the product
• The product produced smoke or a strange smell
This may result in fire or electric shock.
Be careful in handling the adapter to prevent any external shocks to it.
An external shock may cause damage to the adapter.
ENGLISH
If any of the following occur, unplug the product immediately and
contact your local service centre.
Make sure the power cord is connected securely to the power plug on
the TV.
CAUTION
Unplug the TV from AC mains wall socket if you do not intend to use the
TV for a long period of time. Accumulated dust can cause fire hazard
and insulation deterioration can cause electric leakage/shock/fire.
Install the product where no radio wave occurs.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could be exposed to oil or oil
mist. This may damage the product and cause it to fall.
If water enters or comes into contact with TV, AC adapter or power
cord please disconnect the power cord and contact service centre
immediately. Otherwise, this may result in electric shock or fire.
There should be enough distance between an outside antenna and
power lines to keep the former from touching the latter even when the
antenna falls. This may cause an electric shock.
Do not install the product on places such as unstable shelves or inclined
surfaces. Also avoid places where there is vibration or where the
product cannot be fully supported. Otherwise, the product may fall or
flip over, which may cause injury or damage to the product.
Only use an authorized AC adapter and power cord approved by
LG Electronics. Otherwise, this may result in fire, electric shock,
malfunction or product deformation.
If you install the TV on a stand, you need to take actions to prevent the
product from overturning. Otherwise, the product may fall over, which
may cause injury.
Never Disassemble the AC adapter or power cord. This may result in fire
or electric shock.
5
If you intend to mount the product to a wall, attach VESA standard
mounting interface (optional parts) to the back of the product. When
you install the set to use the wall mounting bracket (optional parts), fix
it carefully so as not to drop.
ENGLISH
Only use the attachments / accessories specified by the manufacturer.
Signal from Remote Control can be interrupted due to external/internal
lighting eg Sunlight, fluorescent lighting. If this occurs turn off lighting
or darken viewing area.
When installing the antenna, consult with a qualified service
technician. If not installed by a qualified technician, this may create a
fire hazard or an electric shock hazard.
When connecting external devices such as video game consoles, make
sure the connecting cables are long enough. Otherwise, the product
may fall over, which may cause injury or damage the product.
We recommend that you maintain a distance of at least 2 to 7 times
the diagonal screen size when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
Do not turn the product On/Off by plugging-in or unplugging the power
plug to the wall outlet. (Do not use the power plug for switch.) It may
cause mechanical failure or could give an electric shock.
Only use the specified type of battery. This could cause damage to the
remote control.
Please follow the installation instructions below to prevent the product
from overheating.
Do not mix new batteries with old batteries. This may cause the
batteries to overheat and leak.
• The distance between the product and the wall should be more
than 10 cm.
• Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
• Do not install the product on a carpet or cushion.
• Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in fire.
Batteries should not be exposed to excessive heat. For example, keep
away from direct Sunlight , open fireplace and electric heaters.
Do not place non-rechargeable batteries in charging device.
Make sure there are no objects between the remote control and its
sensor.
6
Take care not to touch the ventilation openings when watching the TV
for long periods as the ventilation openings may become hot. This does
not affect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the cord
exits the appliance.
Do not press strongly upon the panel with a hand or sharp object such
as nail, pencil or pen, or make a scratch on it, as it may cause damage
to screen.
Avoid touching the screen or holding your finger(s) against it for long
periods of time. Doing so may produce some temporary or permanent
distortion/damage to screen.
When cleaning the product and its components, unplug the power
first and wipe it with a soft cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with water or wipe with a wet
cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,
benzene, alcohol etc., which can damage the product and its panel.
Otherwise, this may result in fire, electric shock or product damage
(deformation, corrosion or breakage).
ENGLISH
Prevent dust collecting on the power plug pins or outlet. This may cause
a fire hazard.
When unplugging the cable, grab the plug and unplug it, by pulling at
the plug.
Don’t pull at the cord to unplug the power cord from the power board,
as this could be hazardous.
When moving the product, make sure you turn the power off first. Then,
unplug the power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a fire
hazard or cause electric shock.
When moving or unpacking the product, work in pairs because the
product is heavy. Otherwise, this may result in injury.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
If the product feels cold to the touch, there may be a small “flicker”
when it is turned on. This is normal, there is nothing wrong with
product.
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this unit
by SWITCH.
7
Preparing
ENGLISH
This panel is an advanced product that contains millions of pixels.
You may see tiny black dots and/or brightly coloured dots (red, blue
or green) at a size of 1 ppm on the panel. This does not indicate a
malfunction and does not affect the performance and reliability of the
product.
This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
You may find different brightness and color of the panel depending on
your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not
related with the product performance, and it is not malfunction.
NOTE
• Image shown may differ from your TV.
• Your TV’s OSD (On Screen Display) may differ slightly from that
shown in this manual.
• The available menus and options may differ from the input source
or product model that you are using.
• New features may be added to this TV in the future.
• The items supplied with your product may vary depending on the
model.
• Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
• For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV’s USB port.
B
B
Displaying a still image for a prolonged period of time may cause image
sticking. Avoid displaying a fixed image on the TV screen for a long
period of time.
Some horizontal lines may appear when the Clear Panel Noise feature is
performed. It is normal and there is no need to be concerned.
Generated sound
“Cracking” noise: A cracking noise that occurs when watching or turning
off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal
deformation is required. Electrical circuit humming/panel buzzing:
A low level noise is generated from a high-speed switching circuit,
which supplies a large amount of current to operate a product. It varies
depending on the product.
This generated sound does not affect the performance and reliability
of the product.
Do not use high voltage electrical goods near the TV (e.g. electric
mosquito-swatter). This may result in product malfunction.
8
A
A
*A <
= 10 mm
*B <
= 18 mm
• Use a certified cable with the HDMI logo attached.
• If you do not use a certified HDMI cable, the screen may not display
or a connection error may occur. (Recommended HDMI cable types)
- High-Speed HDMI®/™ cable (3 m or less)
- High-Speed HDMI®/™ cable with Ethernet (3 m or less)
CAUTION
• Do not use any unapproved items to ensure the safety and product
life span.
• Any damage or injuries caused by using unapproved items are not
covered by the manufacturer’s warranty.
• Some models have a thin film attached on to the screen and this
must not be removed.
• When attaching the stand to the TV set, place the screen facing
down on a cushioned table or flat surface to protect the screen
from scratches.
• Make sure that the screws are inserted correctly and fastened
securely. (If they are not fastened securely enough, the TV may tilt
forward after being installed.) Do not use too much force and over
tighten the screws; otherwise screw may be damaged and not
tighten correctly.
Lifting and moving the TV
Using the button
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
(Depending on model)
• Hold the top and bottom of the TV frame firmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
You can simply operate the TV functions, pressing or moving the
buttons.
Dome Button
ENGLISH
• It is recommended to move the TV in the box or packing material
that the TV originally came in.
• Before moving or lifting the TV, disconnect the power cord and
all cables.
• When holding the TV, the screen should face away from you to
avoid damage.
Joystick Button
or
Basic functions
• When transporting a large TV, there should be at least 2 people.
• When transporting the TV by hand, hold the TV as shown in the
following illustration.
Power On
Power Off
• When transporting the TV, do not expose the TV to jolts or
excessive vibration.
• When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right.
• Do not apply excessive pressure to cause flexing /bending of frame
chassis as it may damage screen.
• When handling the TV, be careful not to damage the protruding
buttons.
Volume
Control
When the TV is turned off,
Place your finger on the
Joystick button and
Press it once and release it.
When the TV is turned on,
place your finger on the
joystick button and press it
once for few seconds and
release it. (However, if the
Menu button is one the
screen, pressing and
holding the joystick button
will let you exit the Menu.
If you place your finger over
the joystick button and move
it left or right, you can adjust
the volume level you want.
If you place your finger over
Programmes the Joystick button and move
it forward or backward, you
Control
can scrolls through the saved
programmes you want.
CAUTION
• Avoid touching the screen at all times, as this may result in damage
to the screen.
• Do not move the TV by holding the cable holders, as the cable
holders may break, and injuries and damage to the TV may occur.
1 If the Menu button is on the screen, pressing and holding the button
will let you exit the Menu.
Adjusting the menu
When the TV is turned on, press the button one time. You can adjust
the Menu items pressing or moving the buttons.
Turns the power off.
Clears on-screen displays and returns to TV viewing.
Changes the input source.
Accesses the main menu.
9
Mounting on a table
(Depending on models)
ENGLISH
1 Lift and tilt the TV into its upright position on a table.
• Leave a 10 cm (minimum) space from the wall for proper
ventilation.
NOTE
The Kensington security system is optional. You can obtain
additional accessories from most electronics stores.
Securing the TV to a wall
(Features may vary depending on models)
10 cm
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
• Do not place the TV near or on sources of heat, as this may result in
fire or other damage.
• Please be sure to connect the TV to the AC-DC power adapter
before connecting the TV’s power plug to a wall power outlet.
WARNING
• If a television is not positioned in a sufficiently stable location,
it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple
precautions such as:
» Using cabinets or stands recommended by the manufacturer
of the television.
» Only using furniture that can safely support the television.
» Ensuring the television is not overhanging the edge of the
supporting furniture.
» Not placing the television on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture
and the television to a suitable support.
» Not standing the televisions on cloth or other materials
placed between the television and supporting furniture.
» Educating children about the dangers of climbing on furniture to reach the television or its controls.
Using the kensington security system
(This feature may vary depending on model)
• Image shown may differ from your TV.
The Kensington security system connector is located at the rear of the
TV. For more information of installation and using, refer to the manual
provided with the Kensington security system or visit http://www.
kensington.com. Connect the Kensington security system cable between
the TV and a table.
10
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
• If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear
of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the flat surface.
CAUTION
• Make sure that children do not climb on or hang on the TV.
NOTE
• Use a platform or cabinet that is strong and large enough to
support the TV securely.
• Brackets, bolts and ropes are not provided. You can obtain
additional accessories from your local dealer.
Mounting on a wall
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the floor. When you attach the TV to other building materials, please
contact qualified personnel. LG recommends that wall mounting be
performed by a qualified professional installer. We recommend the use
of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with
cables connected. When you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is adequately secured to the
wall with enough space to allow connectivity to external devices. It is
advised to connect all the cables before installing fixed wall mounts.
NOTE
10 cm
10 cm
ENGLISH
• When installing the wall mounting bracket, use the adhesive label
or protective cover provided. The adhesive label or protective cover
will protect the opening from accumulating dust and dirt. (Only
when the label or cover is provided)
10 cm
Provided item
10 cm
Standard dimensions for the wall mount kits are described in the
following table.
Separate purchase (Wall mounting bracket)
Model
Wall Mount (mm)
(A x B)
Standard screw
Number of screws
24LH45**
28LH45**
75 x 75
100 x 100
M4 x L10
4
M4 x L10
4
Adhesive label
• When installing the wall mounting bracket, it is recommended to
cover the stand hole using tape, in order to prevent the influx of
dust and insects. (Depending on model)
A
B
Stand hole
CAUTION
• Disconnect the power cord first, and then move or install the TV.
Otherwise electric shock may occur.
• If you install the TV on a ceiling or slanted wall, it may fall and
Result in severe injury. Use an authorized LG wall mount and
contact the local dealer or qualified personnel.
• Do not over tighten the screws as this may cause damage to the TV
And void your warranty.
• Use the screws and wall mounts that meet the VESA standard. Any
Damages or injuries by misuse or using an improper accessory are
Not covered by the manufacture’s warranty.
• Screw length from outer surface of back cover should be under
8 mm.
• When attaching a wall mounting bracket to the TV, insert the wall
mount spacers into the TV wall mount holes to adjust the vertical
angle of the TV. (Only when the item of the following form is
provided)
Provided item
Wall mount spacer
Wall mount Pad
Back Cover
Wall mount Pad
Back Cover
Standard screw
: M4 x L10
Max. 8 mm
11
ENGLISH
Connections (notifications)
Remote control
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external device’s
connection, refer to the manual provided with each device.
(Depending on model)
Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, gaming devices, and other external
devices.
To replace batteries, open the battery cover, replace batteries (1.5
V AAA) matching the and ends to the label inside the
compartment, and close the battery cover. To remove the batteries,
perform the installation actions in reverse.
NOTE
• The external device connection may differ from the model.
• Connect external devices to the TV regardless of the order of the
TV port.
• If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder
or VCR. For more information of recording, refer to the manual
provided with the connected device.
• Refer to the external equipment’s manual for operating
instructions.
• If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
CAUTION
• Do not mix old and new batteries, as this may damage the remote
Control.
• In Analogue TV and some countries, some remote control buttons
may not work.
• The remote control will not be included depending upon sales market.
Make sure to point the remote control toward the remote control sensor
on the TV.
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
AV MODE
• Use a signal splitter to use more than 2 TVs.
• If the image quality is poor, install a signal amplifier properly to
improve the image quality.
• If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
• An antenna cable and converter are not supplied.
Adapter connection
(Depending on model)
CAUTION
• Please be sure to connect the TV to the AC-DC power adapter
before connecting the TV’s power plug to a wall power outlet.
Other connections
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
NOTE
• Supported HDMI Audio format :
Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),
PCM (32 kHz, 44.1 kHz, 48 kHz, 88 kHz, 96 kHz, 176 kHz, 192 kHz)
12
A
BOLLY
WOOD
A
FAV
(POWER) Turns the TV on or off.
Returns to the TV viewing from any mode.
Accesses the Quick menus.
Selects an AV mode.
Switches the BOLLYWOOD sound mode.
Changes the input source.
Number buttons Enters numbers.
Accesses the saved programme list.
Returns to the previously viewed programme.
AV MODE
BOLLY
WOOD
FAV
C
Licenses
Supported licenses may differ by model. For more information about
licenses, visit www.lg.com.
ENGLISH
1
B
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
B
Adjusts the volume level.
Accesses your favourite programme list.
Selects the sound output.
Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next screen.
C
1 Teletext buttons These buttons are used for teletext.
Accesses the main menus.
Navigation buttons (up/down/left/right) Scrolls through
menus or options.
Selects menus or options and confirms your input.
Returns to the previous level.
Clears on-screen displays and returns to TV viewing.
) Controls media contents.
Control buttons (
Coloured buttons These access special functions in some menus.
: Red,
: Green,
: Yellow,
: Blue)
(
This DivX Certified® device has passed rigorous testing to ensure it
plays DivX® video.
To play purchased DivX movies, first register your device at vod.divx.
com. Find your registration code in the DivX VOD section of your
device setup menu.
DivX Certified® to play DivX® video up to HD 1080p, including
premium content.
DivX®, DivX Certified® and associated logos are trademarks of DivX,
LLC and are used under license.
Covered by DivX Patents 7,295,673; 7,515,710; RE45,052; and others
available at [www.divx.com/patents].
Open source software
notice information
To obtain the source code under GPL, LGPL, MPL, and other open source
licenses, that is contained in this product, please visit http://opensource.
lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date
on which you purchased the product.
13
Watching TV
Watching TV
1 In Standby mode, press
2 Press
ENGLISH
Turning the TV on for the first time
When you turn the TV on for the first time, the Initial setting screen
appears. Select a language and customize the basic settings.
(POWER) to turn the TV on.
INPUT and select TV.
3 To turn the TV off, press
mode.
(POWER). The TV switches to Standby
1 Connect the power cord to a power outlet. The Power indicator turns
red and the TV switches to Standby mode.
Managing programmes
2 In Standby mode, press the power button on the remote control or
local key to turn the TV on. The Initial setting screen appears if you
turn the TV on for the first time.
Automatically setting up programme
NOTE
• You can also access Factory Reset by accessing OPTION in the
main menu.
3 Follow the on-screen instructions to customize your TV settings
according to your preferences.
Menu Language
Selects a language to display.
Mode Setting
Selects Home Use for the home
environment.
Time Setting
Sets the time.
Auto Tuning
Scans and saves available
programmes automatically.
1 Press SETTINGS and the Navigation buttons to scroll to SETUP and
press
.
2 Press the Navigation buttons to scroll to Auto Tuning and press
.
3 Press the Navigation buttons to scroll to Start and select Start to
begin auto tuning. The TV scans and saves available programmes
automatically.
4 When you return to the previous menu, press
Manual Tuning lets you manually tune and arrange the stations in
whatever order you desire.
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
2 Press the Navigation buttons to scroll to Manual Tuning.
• To display images in the best quality for your home environment,
select Home Use.
• Store Demo is suitable for the retail environment.
• If you select Store Demo, any customized settings will switch
back to the default settings of Store Demo in 5 minutes.
.
NOTE
• If you do not complete the Initial setting, it will appear whenever
the TV turns on.
• Disconnect the power cord from the power outlet when you do not
use the TV for a long period of time.
5 To turn the TV off, press the power button on the remote control.
3 Press the Navigation buttons to scroll to Storage.
4 Press the Navigation buttons or Number buttons to select the desired
programme number.
5 Press the Navigation buttons to scroll to System.
6 Press the Navigation buttons to scroll to TV System.
7 Press the Navigation buttons to scroll to Band.
8 Press the Navigation buttons to scroll to V/UHF or Cable.
9 Press the Navigation buttons to scroll to Channel.
10 Press the Navigation buttons and then select the desired Channel
number with the Navigation buttons or Number buttons.
11 Press the Navigation buttons to scroll to Search.
12 Press the Navigation buttons to scroll and start Searching.
13 Press the OK
to store it.
14 When you return to the previous menu, press
NOTE
• To store another programme, repeat steps 3 to 13.
14
.
Manually setting up programme
NOTE
4 When the basic settings are complete, press the
Use this to automatically find and store all available programmes.
.
Assigning a station name
You can assign a station name with five characters to each programme
number.
1 Press LIST to access the programme list.
2 Press the Navigation buttons to scroll to Manual Tuning.
2 Press the Navigation buttons to select to desired programme and
press OK .
3 Press the Navigation buttons to scroll to Name.
3 When you return to the previous menu, press LIST.
4 Press the Navigation buttons to scroll to select the position and
make your choice of the second character, and so on. You can use the
alphabet A to Z, the number 0 to 9, +/ -, and blank and press OK .
5 Press the OK
to store it.
6 When you return to the previous menu, press
.
NOTE
• You may find some blue programmes. They have been set up to be
skipped by auto programming or in the programme edit mode.
• Some programmes with the programme number shown in the
programme list indicate there is no station name assigned.
Using additional options
Fine Tuning
Normally fine tuning is only necessary if reception is poor.
Adjusting aspect ratio
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
2 Press the Navigation buttons to scroll to Manual Tuning.
3 Press the Navigation buttons to scroll to Fine.
4 Press the Navigation buttons to fine tune for the best picture and
sound.
5 Press the OK
ENGLISH
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
Selecting a programme on the programme
list
to store it.
6 When you return to the previous menu, press
.
Resize an image to view at its optimal size by pressing Q.MENU or
accessing Aspect Ratio in the PICTURE menu.
NOTE
• The available ratio varies depending on the input source.
- 16:9 : Resizes images to fit the screen width.
Editing your programme list
When a programme number is skipped, it means that you will be
button during TV viewing.
unable to select it using
If you wish to select the skipped programme, directly enter the
programme number with the NUMBER buttons or select it in the
Programme edit menu.
- Just Scan : Displays video images in the original size without
removing parts of the edge of the image. (This function works
in Component/HDMI (720p / 1080i / 1080p) Mode.)
This function enables you to skip the stored programmes.
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
2 Press the Navigation buttons to scroll to Programme Edit.
3 Edit programmes using the following buttons.
Button
Description
NOTE
Deletes a programme.
Red button
Press the Red button twice. The selected
programme is deleted, all the following
programmes are shifted up one position.
Moves a programme.
Yellow button
Blue button
Press the Yellow button again to release this
function.
• If you select Just Scan, you may see image noises at the edge of
the original signal.
- Original : When your TV receives a wide screen signal it will
automatically change to the picture format broadcasted.
(4:3
4:3)
(16:9
16:9)
Selects a programme number to be skipped. Press
the Blue button again to release the skipped
programme.
4 When you return to the previous menu, press
.
15
- 4:3 : Resizes images to the previous standard 4:3.
Using the input list
Selecting an input source
INPUT to access the input sources.
ENGLISH
1 Press
- 14:9 : You can view a picture format of 14:9 or a general TV
programme in the 14:9 mode.
• The connected device displays on each input source.
2 Press the Navigation buttons or input button to scroll to one of the
input sources and press OK .
* Image shown may differ from your TV.
A Type)
Input List
- Zoom : Formats an image to fit the screen width. The top and
bottom of the image may not appear.
RGB-PC
AV
HDMI
Antenna
Exit
B Type)
Input List
- Cinema Zoom 1 : Formats an image to the cinemascope ratio,
2.35:1.
To change the ratio of the cinema zoom, press or and its
range is from 1 to 16.
Component
AV
HDMI
Antenna
Exit
Input source
Description
TV
Watch TV over the air and cable broadcast.
AV
Watch video from a VCR or other external
devices.
RGB-PC
View a PC display on the screen.
(Depending on model)
NOTE
• If you enlarge or reduce an image, the image may be distorted.
Using the input list.
Changing AV modes
Each AV MODE has optimized image and sound settings.
Press AV MODE repeatedly to select an appropriate mode.
Mode
Off
Description
Changes to the previously customized settings.
Cinema
Uses the optimized image and sound settings for a
cinematic look.
Uses the optimized image and sound settings for fast
gaming.
Game
When playing a video game using PlayStation or Xbox.
it is recommended to use the Game mode.
When in Game mode, functions related to picture
quality will be optimized for playing games.
16
Component
Select it when using the DVD or the Digital
(Depending on model) set-top box depends on connector.
HDMI
Watch video from a HTS or other high
definition devices.
Entertainment
(Depending on model)
Connecting USB storage devices
Connect USB storage devices (USB memory) to the TV and use
multimedia features (See “Browsing files” on page 17).
USB IN
Connect a USB flash memory or USB memory card reader to the TV as
shown on the following illustration.
To disconnect a USB storage device, make sure to end the connection
properly to prevent damages to the TV or files.
1 Press Q.MENU to access the quick menus.
2 Press the Navigation buttons to scroll to Eject and press OK
.
3 Disconnect the USB storage device only when the message says that
it is safe to remove.
CAUTION
• Do not turn the TV off or remove a USB storage device while the
USB storage device is connected to the TV, as this could result in loss
of files or damage to the USB storage device.
• Back up your files saved on a USB storage device frequently, as you
may lose or damage the files and this may be not covered by the
manufacturer’s warranty.
Tips for using USB storage devices
• Only a USB storage device is recognizable.
• If the USB storage device is connected through a USB hub, the
device is not recognizable.
• A USB storage device using an automatic recognition programme
may not be recognized.
• A USB storage device which uses its own driver may not be
recognized.
• The recognition speed of a USB storage device may depend on each
device.
ENGLISH
* Image shown may differ from your TV.
• Please do not turn off the TV or unplug the USB device when
the connected USB storage device is working. When such device
is suddenly separated or unplugged, the stored files or the USB
storage device may be damaged.
• Please do not connect the USB storage device which was artificially
manoeuvred on the PC. The device may cause the product to
malfunction or fail to be played. Never forget to use only a USB
storage device which has normal music files, image files or movie
files.
• Please use only a USB storage device which was formatted as a
FAT16, FAT32, NTFS file system.
• Please connect a USB storage device with the cable offered by the
device maker.
• Some USB storage devices may not be supported or operated
smoothly.
• Be sure to back up important files since data stored in a USB
memory device may be damaged. We will not be responsible for
any data loss.
• If a USB memory device is connected to a USB multi-card reader, its
volume data may not be detected.
• If the USB memory device does not work properly, disconnect and
reconnect it.
• How fast a USB memory device is detected differs from device to
device.
• The recommended capacity is 1 TB or less for a USB external hard
disk and 32 GB or less for USB memory.
• Any device with more than the recommended capacity may not
work properly.
• USB storage devices below USB 2.0 are supported as well. But they
may not work properly in the movie list.
• Maximum of 999 folders or files can be recognized under one
folder.
• If there are a lot of folders or files all within one folder, the device
may not be able to access these properly.
• For external USB HDDs, it is recommended that you use devices
with a rated voltage of less than 5 V and a rated current of less
than 0.5A.
Browsing files
Access the photo, music, or movie lists and browse files.
1 Connect a USB storage device.
2 Press SETTINGS to access the main menus.
3 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
4 Press Navigation buttons to scroll to PHOTO LIST, MUSIC LIST or
MOVIE LIST and press OK .
* Image shown may differ from your TV.
PHOTO LIST
MUSIC LIST
MOVIE LIST
17
3
PHOTO LIST
Page 1/1
No Marked
Free Space 4 GB
Up Folder
ENGLISH
2
3872 x 2592, 2604 KB
Up Folder
KY103
09/15/2016
KY101
04/03/2016
KY104
10/12/2016
KY102
09/03/2016
KY105
11/27/2016
GUU
11/27/2016
JMJ005
11/27/2016
JMJ002
11/27/2016
JMJ006
11/27/2016
JMJ003
11/27/2016
JMJ007
11/27/2016
JMJ004
11/27/2016
JMJ008
11/27/2016
ꔂ Move
ꔵ Move Page
ꔉ PopUp Menu
ꘂ Mark
Page 1/1
• You can play JPEG files only.
• Non-supported files are displayed in the form
of predefined icon.
Music
Duration
ꔉ PopUp Menu
Top Folder
DriveA
6
ꔵ Move Page
Option
3
MOVIE LIST
Exit
4
Page 1/1
Movie
USB Device
No Marked
Free Space 4 GB
Title
Duration
DriveA
5
2
4 folder(s), 2 file(s)
Up Folder
ꔂ Move
ꔉ PopUp Menu
ꘂ Mark
ꔵ Move Page
Exit
Description
1
Moves to the upper level folder.
2
Preview: Displays the thumbnail/folder name of the file in
the selected folder.
3
4
5
6
• Sampling rate MPEG1 Layer3 : 32 kHz, 44.1
kHz, 48 kHz
• Sampling rate MPEG2 Layer3 : 16 kHz, 22.05
kHz, 24 kHz
• Sampling rate MPEG2.5 Layer3 : 8 kHz, 11.025
kHz, 12 kHz
Up Folder
ꘂ Mark
Current page/Total pages.
Total number of marked files.
6
MP3
Bit rate 32 kbps to 320 kbps
00:00 / 01:34
ꔂ Move
No.
Progressive : 64 x 64 to 1024 x 768
6
5
ꕗ
JPEG
Baseline : 64 pixel (W) x 64 pixel (H) - 15360 pixel
(W) x 8640 pixel (H)
Free Space 4 GB
Title
Supported file format
Available size
USB Device
No Marked
2
1
Photo
4
DriveA
1
5
Exit
3
MUSIC LIST
Type
USB Device
DriveA
GUU.JPG
1
Supported file format
4
DAT, MPG, MPEG, VOB, AVI, DIVX, MP4, MKV, TS, TRP,
TP, ASF, WMV, FLV, RM, RMVB
Movie (*.mpg/*.mpeg/*dat/*.ts/*.trp/*.tp/*.
vob/*.mp4/*.mov/*.mkv/*.divx/*.avi/*.asf/*.
wmv/*.flv/*.avi(motion-jpeg)/*.mp4(motionjpeg)/*.mkv(motion-jpeg)/*.rm/*.rmvb)
supporting file
Video format : DivX 3.11, DivX 4, DivX 5, DivX 6,
Xvid1.00, Xvid1.01, Xvid1.02, Xvid1.03, Xvid1.10
beta-1/beta-2, Mpeg-1, Mpeg-2, Mpeg-4, H.264/
AVC, VC1, JPEG, Sorenson H.263
Audio format : Dolby Digital, AAC, Mpeg, MP3,
LPCM, ADPCM, WMA
Bit rate : within 32 kbps to 320 kbps (MP3)
Contents under the folder focused on 1.
Available buttons on the remote control.
External Subtitle format : *.smi/*.srt/*.su
b(MicroDVD,Subviewer1.0/2.0)/*.ass/*.ssa/*.
txt(TMPlayer)/*.psb(PowerDivX)
Internal Subtitle format : Only XSUB (It is the
subtitle format used in DivX6 files)
18
Viewing photos
6 The following options are available while viewing photos.
View image files saved in a USB storage device. The displays on the
screen may differ from the model.
ENGLISH
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
3 Press the Navigation buttons to scroll to PHOTO LIST and press
OK .
ꔊ
4 Press the Navigation buttons to scroll to a folder/file you want and
press OK .
Slide show �
2/13
ꔡ
BGM
�
ꔋ
�
Option
Hide
5 View photos by using the following menus buttons.
PHOTO LIST
DriveA
GUU.JPG
3872 x 2592, 2604 KB
Up Folder
ꔂ Move
USB Device
Page 1/1
No Marked
Free Space 4 GB
Up Folder
KY103
09/15/2016
KY101
04/03/2016
KY104
10/12/2016
KY102
09/03/2016
KY105
11/27/2016
GUU
11/27/2016
JMJ005
11/27/2016
JMJ002
11/27/2016
JMJ006
11/27/2016
JMJ003
11/27/2016
JMJ007
11/27/2016
JMJ004
11/27/2016
JMJ008
11/27/2016
ꔉ PopUp Menu
ꘂ Mark
OK
Views the highlighted file or enters the mark
mode.
Moves to the previous or next page.
FAV
View
Close
If there are no selected photos, all photos saved in
the current folder display during a slideshow.
To set a slideshow speed, select Option.
BGM
Turns the background music on or off. To set the
background music folder, select Option.
Rotates photos clockwise (90°, 180°, 270°, 360°).
NOTE
(Rotate)
Hide
• The supported photo size is limited. You
cannot rotate a photo if the resolution of the
rotated width is larger than the supported
resolution size.
Hides the option window.
To display the options, press OK
.
Enters the mark mode.
Menu
Mark All
Slideshow
Description
Scrolls through the files.
Description
Starts or stops a slideshow with selected photos.
Exit
Button
Navigation
button
ꔵ Move Page
Option
Description
Views the selected photo.
Selects all files.
Exits the Mark Mode.
NOTE
• Non-supported files are displayed the preview image by icon only
.
• Abnormal files are displayed in the form of bitmap
.
Q.MENU options for photo list
1 Press Q.MENU.
A pop-up window will appears.
2 Press the Navigation buttons to scroll to Set photo view. and press
OK .
3 Press the Navigation buttons to scroll to one of the following options
and press OK .
Set photo view.
Option
Description
Slide Speed
Selects a slideshow speed (Fast, Normal,
Slow).
Music Folder
Selects a music folder for the background
music.
19
Set video.
6 Control playback by using the following buttons.
Allows you to change Video presets. (See p. 25)
Button
ENGLISH
Set audio.
Stops playback.
Allows you to change Audio presets. (See p. 27)
Plays a music file.
Pauses or resumes playback.
Listening to music
Skips to the next file.
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
3 Press the Navigation buttons to scroll to MUSIC LIST and press
OK .
Skips to the previous file.
When playing,
or
When you press the
button, the previous
music file will be played.
When you press the
button, the next
music file will be played.
4 Press the Navigation buttons to scroll to a folder/file you want and
press OK .
5 Play music by using the following menus/buttons.
MUSIC LIST
Description
Page 1/1
EXIT
USB Device
No Marked
DriveA
Free Space 4 GB
Title
When you press the EXIT button, only the
music will be stopped and the player will go to
TV viewing.
When using the or
button during
playback a cursor indicating the position can
be played.
Duration
or
00:00 / 01:34
ꕗ
Q.MENU options for music list
Up Folder
ꔂ Move
ꘂ Mark
ꔉ PopUp Menu
Option
Button
Navigation
button
OK
ꔵ Move Page
Exit
Description
Scrolls through the files.
Views the highlighted file or enters the mark
mode.
Moves to the previous or next page.
FAV
Enters the mark mode.
Menu
Play
Play with Photo
Mark All
Close
Description
Plays the selected music file.
1 Press Q.MENU.
A pop-up window will appears.
Set audio.
Allows you to change Audio presets. (See p. 26)
NOTE
• The TV will not play copy protected files.
• If the TV is not in use for some time during playback, the
information box as a screensaver will appear to prevent image
burn. To return to the Music list screen, press OK or BACK.
File name
Musics
001.mp3
Displays photos during playback.
Selects all files.
Exits the Mark Mode.
ꕗ 00:53 / 05:31
Time elapsed / Duration
20
Viewing movies
Button
Description
Stops the playback.
2 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
Plays a video.
3 Press the Navigation buttons to scroll to MOVIE LIST and press
OK .
Pauses or resumes the playback.
Scans backward in a file.
4 Press the Navigation buttons to scroll to a folder/file you want and
press OK .
Scans forward in a file.
5 Play movie by using the following menus/buttons.
MOVIE LIST
Top Folder
DriveA
Page 1/1
Q.MENU
BACK
USB Device
No Marked
ENGLISH
1 Press SETTINGS to access the main menus.
Shows the Option menu.
Hides the menu on the full-sized screen.
Free Space 4 GB
Title
EXIT
Duration
DriveA
or
4 folder(s), 2 file(s)
Returns to normal TV viewing.
Skips to specific points in a file during
playback. The time of a specific point will
appear on the status bar. In some files, this
function may not work properly.
Up Folder
ꔂ Move
ꔵ Move Page
ꔉ PopUp Menu
ꘂ Mark
Exit
Button
Navigation button
Description
Scrolls through the files.
Views the highlighted file or enters the
mark mode.
OK
Moves to the previous or next page.
FAV
Enters the mark mode.
Menu
Description
Plays the selected movie file.
Play
Once a movie file finishes playing, the next
selected one will be played automatically.
Mark All
Close
Marks all movie files on the screen.
Exits the Mark Mode.
6 Control playback by using the following buttons.
ꔋ
↓07:10
00:22:05
Tips for using playing video files
• • • • Some user-created subtitles may not work properly.
Some special characters are not supported in subtitles.
HTML tags are not supported in subtitles.
Subtitles in languages other than the supported languages are not
available.
• Changing font and colour in subtitles is not supported.
• Subtitles in languages other than one specified are not supported.
• Video files with subtitle files of 1 MB or larger may not be played
properly.
• The screen may suffer temporary interruptions (image stoppage,
faster playback, etc.) when the audio language is changed.
• A damaged movie file may not be played correctly, or some player
functions may not be usable.
• Movie files produced with some encoders may not be played
correctly.
• If the video and audio structure of recorded file is not interleaved,
either video or audio is outputted.
• HD videos with a maximum of 1920 x 1080 @ 25/30P or 1280 x 720
@ 50/60P are supported, depending on the frame.
• Videos with resolutions higher than 1920 X 1080 @ 25/30P or 1280
x 720 @ 50/60P may not work properly depending on the frame.
• Movie files other than the specified types and formats may not
work properly.
• Max bit rate of playable movie file is 20 Mbps. (only, Motion JPEG
: 10 Mbps)
• We do not guarantee smooth playback of profiles encoded level 4.1
or higher in H.264/AVC.
Option
21
ENGLISH
• DTS Audio codec is not supported.
• A movie file more than 30 GB in file size is not supported for
playback. The file size limit is dependent on the encoding
environment.
• A DivX movie file and its subtitle file must be located in the same
folder.
• A video file name and its subtitle file name must be identical for it
to be displayed.
• Playing a video via a USB connection that doesn’t support high
speed may not work properly.
• Files encoded with GMC (Global Motion Compensation) and Qpel
(Quarterpel Motion Estimation) may not be played.
• Trick Mode does not support other functions than if video files do
not have index information.
• Video file names that contain special characters may not be
playable.
Code Page
Latin1
Cyrillic
Support Language
English, French, Spanish, Portuguese, Bahasa
Malaysia, Bahasa Indonesia
Russian
Thai
Thai
Hebrew
Hebrew
Arabic
Arabic, Persian, Kurdish
Vietnam
Vietnamese
NOTE
• Only 10,000 of sync blocks can be supported within the subtitle file.
• When playing a video, you can adjust the Picture Size by pressing
Q.MENU or accessing Aspect Ratio in the PICTURE menu.
When you select the Set video.
Video options
1 Press Q. MENU to access the Pop-Up menus.
1 Press the Navigation buttons to scroll to make appropriate
adjustments. (See p. 24)
2 Press the Navigation buttons to scroll to Set video play., Set video.
or Set audio. and press OK .
When you select the Set audio.
When you select the Set video play.
1 Press the Navigation buttons to scroll to show the Sound Mode,
Auto Volume, Balance.
1 Press the Navigation buttons to scroll to show the Picture Size,
Audio Language, Subtitle.
2 Press the Navigation buttons to scroll to make appropriate
adjustments. (See p. 26)
2 Press the Navigation buttons to scroll to make appropriate
adjustments.
Menu
Description
Picture Size
Selects your desired picture format during
movie play.
Audio Language
Changes the Language Group of the audio
during movie play. Files with a single audio
track cannot be selected.
Subtitle
Language
Code Page
Sync
DivX® VOD Guide
DivX® VOD Registration
In order to play purchased or rented DivX® VOD contents, you should
register your device with 10 digit DivX registration code from your
device at www.divx.com/vod.
Turns on/off the subtitle.
1 Press SETTINGS to access the main menus.
Activated for SMI subtitle and can select the
language within the subtitle.
2 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
Selects the font for subtitle.
3 Press the Navigation buttons to scroll to DivX(R) VOD and press OK
.
When set to default, same font as general
menu will be used.
Adjusts the time synchronisation of the
subtitle from -10 secs to +10 secs by steps of
0.5 secs during movie play.
4 Press the Navigation buttons to scroll to Registration and press
OK .
5 View the registration code of your TV.
You must register your device to
play DivX(R) protected videos.
Registration code : **********
Register at http://vod.divx.com
Close
22
6 When you are finished, press EXIT. When you return to the previous
menu, press BACK.
NOTE
Menu
Movie files are supported as follows
Resolution : Under 1920 x 1080 (W x H) pixels
Frame Rate : Under 30 frames/sec
Video Codec : MPEG 1, MPEG 2, MPEG 4, H.264/AVC, DivX 3.11,
DivX 4, DivX 5, DivX 6, Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.03,
Xvid 1.10-beta1, Xvid 1.10-beta2, JPEG, VC1, Sorenson H.263/H.264
Description
SETUP
PICTURE
NOTE
• Once the deregistration is executed, you must register your device
again to see DivX® VOD contents.
Adjusts the sound quality,
effect, or volume level.
TIME
Sets the time, date, or
timer feature.
OPTION
Customizes the general
settings.
LOCK
Locks or unlocks
programmes.
INPUT
Views the input sources
with their labels.
ENTERTAINMENT
Displays photo and play
music, movie, game
(Depending on model)
contents.
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
3 Press the Navigation buttons to scroll to DivX(R) VOD and press
OK .
4 Press the Navigation buttons to scroll to Deregistration and press
OK .
Adjusts the image size,
quality, or effect.
AUDIO
DivX® VOD Deregistration
You should deregister your device with 8 digit DivX deregistration code
from your device at www.divx.com/vod.
Sets up and edit
programmes.
ENGLISH
• • • • 5 Press the Navigation buttons to select Yes to confirm.
Customizing settings
Deregistration code :
********
Deregister at http://vod.divx.com
Continue with registration?
Yes
SETUP settings
No
6 When you are finished, press EXIT. When you return to the previous
menu, press BACK.
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
BACK.
* Image shown may differ from your TV.
Customizing TV setting
* Image shown may differ from your TV.
SETUP
Move
Move
OK
OK
Auto Tuning
Manual Tuning
Programme Edit
Accessing main menus
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to one of the following menus
and press OK .
3 Press Navigation buttons to scroll to the setting or option you want
and press OK .
4 When you are finished, press EXIT.
23
The available programme settings are described in the following:
Setting
Description
The available picture settings are described in the following.
Setting
ENGLISH
Auto Tuning
Tunes and stores all available
programmes through antennas inputs.
(See p. 14)
Manual Tuning
Tunes and stores the programmes you
want manually. (See p. 14)
Programme Edit
Edits programmes. (See p. 15)
Aspect Ratio
Reduces the power consumption by adjusting
the screen brightness.
Option
PICTURE settings
1 Press SETTINGS and the Navigation buttons to scroll to PICTURE.
Energy Saving
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
Aspect Ratio
Move
: 16:9
Move
100
•Contrast
100
•Brightness
50
•Sharpness
20
•Colour
55
•Tint
The Energy Saving is off.
Minimum/
Medium/
Maximum
Selects the brightness level.
Screen off
The screen turns off in 3 seconds.
• When you select Screen Off, the screen
will be turned off in 3 seconds and Screen
Off will start.
• If you adjust “Energy Saving- Maximum”,
Backlight feature will not work.
OK
OK
Selects one of the preset image or customizes
options in each mode for the best TV screen
performance. You are also able to customize
advanced options of each mode.
ꕊ Energy Saving : Off
: Standard
Picture Mode
•Backlight
Off
NOTE
BACK.
* Image shown may differ from your TV.
PICTURE
Description
Changes the image size to view images at its
optimal size. (See p. 15)
Mode
0
R
G
• Colour Temperature C20
W
C
Vivid
Adjusts the video image for the
retail environment by enhancing
the contrast, brightness, colour,
and sharpness.
Standard
Adjusts the image for the normal
environment.
•Advanced Control
•Reset
Eye Comfort Mode : ON
Picture Mode
Cinema
Soccer /
Cricket
(Depending
on model)
Game
Optimizes the video images for
a cinematic look to enjoy movies
as if you are in a movie theatre.
Optimizes the video image for
high and dynamic actions by
emphasizing primary colours
such as white, grass, or sky blue.
Optimizes the video image for
a fast gaming screen such as
games.
If you turn this option on, colour temperature
will be automatically adjusted to reduce eye
strain.
Eye Comfort
Mode
24
Option
On
Automatically adjusts the screen
colour temperature.
Off
Turns off the Eye Comfort
Mode.
(Depending on model)
Setting
Setting
Description
Customizes the PC display options in RGB mode.
Resolution
Sets the desired resolution.
Options may only be selected
when the PC resolution is set to
1024 x 768 @ 60 /
1280 x 768 @60 /
1360 x 768 @ 60 /
1366 x 768 @ 60 (default).
Auto
config.
Sets to adjust the screen
position, clock, and phase
automatically. The displayed
image may be unstable for
a few seconds while the
configuration is in progress.
Position/
Size/Phase
Adjusts the options when the
picture is not clear, especially
when characters are shaky,
after the auto configuration.
Screen
(RGB-PC)
Reset
Setting
Description
Backlight
Adjusts the brightness of the screen
by controlling the LCD backlight. If
you decrease the brightness level, the
screen becomes darker and the power
consumption will be reduced without
any video signal loss.
Contrast
Increases or decreases the gradient
of the video signal. You may use
Contrast when the bright part of the
picture is saturated.
Brightness
Adjusts the base level of the signal in
the picture.
Sharpness
Adjusts the level of crispness in the
edges between the light and dark
areas of the picture. The lower the
level, the softer the image.
Adjusts the balance between red and
green levels.
Tint
Adjusts the overall tone of the screen
as desired.
Colour Temperature
Advanced Control
Reset
Set to warm to enhance hotter colours
such as red, or set to cool to see less
intense colours with more blue.
Customizes the advanced options.
Restores the options of each mode to
the factory default.
Advanced image options (Depending on model)
Setting
Description
Dynamic Contrast
Adjusts the contrast to keep it at the best
level according to the brightness of the
screen. The picture is improved by making
bright parts brighter and dark parts darker.
Restores the options to the
default setting.
Basic image options
Adjusts intensity of all colours.
ENGLISH
Option
Description
Colour
Dynamic Colour
Adjusts screen colours so that they look
livelier, richer and clearer. This feature
enhances hue, saturation and luminance
so that red, blue and green white look
more vivid.
Noise Reduction
Reduces screen noise without compromising
video quality.
You can adjust brightness of dark area and
middle gray level area of the picture.
Gamma
Black Level
Motion Eye Care
Film Mode
• Low: Make the dark and middle gray
level areas brighter.
• Medium: Express the original picture
level.
• High: Make the dark and middle gray
level area darker.
Sets black level of the screen to proper level.
This function is available in the following
modes: RF, AV or HDMI.
• Low: The reflection of the screen gets
darker.
• High: The reflection of the screen gets
brighter.
Adjusts screen brightness to prevent eye
glare.
Makes video clips recorded in film look more
natural.
This feature operates only in 480i / 576i /
1080i Resolution.
25
Setting
Description
Setting
Advanced control
Selects one of the preset sound modes or
customizes options in each mode.
Maximizes the utilization of colour to
increase colour quality.
• Standard: Displays standard set of
colours.
• Wide: Increase number of colours used.
ENGLISH
Colour Gamut
Mode
Shows clearer and distinctive yet natural
edges of the video.
Edge Enhancer
NOTE
1 Press SETTINGS and the Navigation buttons to scroll to AUDIO.
Standard
Select when you want
standard-quality sound.
Music/
Bollywood
(Depending
on model)
Select when you listen to
music.(Bollywood is india
special music mode)
Sound Mode
Soccer / Cricket
(Depending on
model)
Game
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
* Image shown may differ from your TV.
Move
Auto Volume
Balance
Sound Mode
TV Speaker
Move
: On
0
: Standard
•Treble
•Bass
•Reset
L
Select when you watch
sports events.
Select when you play games.
Option
Treble
Controls the dominant
sounds in the output. When
you turn up the treble, it will
increase the output to the
higher frequency range.
Bass
Controls the softer sounds in
the output. When you turn
up the bass, it will increase
the output to the lower
frequency range.
Reset
Resets the sound mode to
the default setting.
BACK.
AUDIO
Select when you watch
movies.
Cinema
• Depending on input signal or other picture settings, the range of
detailed items for adjustment may differ.
AUDIO settings
Description
OK
OK
R
50
50
: On
TV Speaker
Turns off the internal speaker of the TV when
using an external Hi-Fi system.
The available audio settings are described in the following.
Setting
Description
Auto Volume
Activates the Auto Volume feature to keep the
volume level consistent whenever you change
programmes. The volume level may not be
consistent due to different signal conditions of
broadcasting stations.
Balance
Adjust balance between the left and right
speakers according to your room environment.
This feature may not be applied based on country broadcasting
circumstance.
Stereo/Dual Reception
When a programme is selected, the sound information for the station
appears with the programme number and station name.
Press I/II button to select the Multi Audio menu.
Broadcast
MONO
Stereo
STEREO
Dual
NICAM
26
On Screen Display
Mono
DUAL I , DUAL II , DUAL I + II
NICAM
yyMono sound selection
If the stereo signal is weak in stereo reception, you can switch to
mono. In mono reception, the clarity of sound is improved.
DUAL I
DUAL I I
DUAL I+I I
Sends the primary broadcast language to the
loudspeakers.
Sends the secondary broadcast language to the
loudspeakers.
Sends a separate language to each loudspeaker.
1 Press SETTINGS and the Navigation buttons to scroll to TIME.
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
ENGLISH
yyLanguage selection for dual language broadcast
If a programme can be received in two languages (dual
language), you can switch to DUAL I, DUAL II or DUAL I+II.
TIME settings
BACK
* Image shown may differ from your TV.
TIME
Move
Move
Clock
Off Time
On TIme
Sleep Timer
Automatic Standby
Auto Off(On Time)
OK
OK
: Off
: Off
: Off
: 4 hours
: Off
Nicam Reception
If the TV is equipped with a receiver for NICAM reception, high quality
NICAM (Near Instantaneous Companding Audio Multiplex) digital sound
can be received.
Sound output can be selected according to the type of broadcast
received.
The available time settings are described in the following.
Setting
Clock
Off Time /
On Time
3 When NICAM dual is received, you can select NICAM DUAL I,
NICAM DUAL II or NICAM DUAL I+II or FM MONO.
Speaker Sound Output Selection
In AV, Component, HDMI mode, you can select output sound for the left
and right loudspeakers.
Sleep Timer
Select the sound output.
L+R:
L+L:
R+R:
Audio signal from audio L input is sent to the left
loudspeaker and audio signal from audio R input is sent
to the right loudspeaker.
Audio signal from audio L input is sent to left and right
loudspeakers.
Audio signal from audio R input is sent to left and right
loudspeakers.
Sets the time.
Sets the time to turn on or off the TV
automatically. To use this function, you should
set the current time and date in advance.
1 When NICAM mono is received, you can select NICAM MONO or
FM MONO.
2 When NICAM stereo is received, you can select NICAM STEREO or
FM MONO.
If the stereo signal is weak, switch to FM MONO.
Description
Automatic
Standby
(Depending on
model)
Auto Off(On
Time)
(Depending on
model)
NOTE
• If you do not press any button within 2
hours after the TV turns on by the On Time
feature, the TV enters the Standby mode
automatically.
• If you set both Off Time and On Time
features to the same time, the Off Time
feature overrides the On Time feature.
Sets the length of time until the TV to turns off.
When you turn the TV off and turn it on again,
the Sleep Timer feature will be set to off.
If you do not press any button on the TV or
remote control for a certain period, the TV will
automatically switch to standby mode.
If On Time is enabled, the TV will be turned
on at the specified time. If you do not operate
the TV for two hours, the TV will be turned off
automatically.
27
OPTION settings
The available lock settings are described in the following.
ENGLISH
1 Press SETTINGS and the Navigation buttons to scroll to OPTION.
Setting
Description
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
Lock System
Activates or deactivates the lock system.
Set Password
Changes the 4-digit password. The
default PIN is “0 0 0 0”.
BACK.
3 When you return to the previous menu, press
* Image shown may differ from your TV.
OPTION
Move
Move
OK
OK
Block Programme
Menu Language
Input Label
USB AutoRun
Factory Reset
: Home Use
Input Block
Blocks the programmes that contain
inappropriate contents for children
by pressing the Blue button. The Lock
icon appears in front of the blocked
programmes. The programmes can be
selected but the screen blank and the
audio is muted.
Blocks the input sources.
ENTERTAINMENT settings
1 Press SETTINGS and the Navigation buttons to scroll to
ENTERTAINMENT.
The available option settings are described in the following.
Setting
Menu Language
Input Label
USB AutoRun
Factory Reset
Description
Selects a desired language.
Indicates which device is connected to which
input port.
When your TV is turned on with a USB device
connected or when you connect a USB device
to your TV, the photos or videos will be played
automatically.
Customizes the TV settings to suit your
preference. The initial setup screen will
appear when you turn on the TV for the
first time.
Home Use
Selects it for the Home
environment.
Store Demo
Selects it for the retail
environment.
3 When you return to the previous menu, press
BACK.
* Image shown may differ from your TV.
ENTERTAINMENT
Move
Move
OK
OK
Photo List
Music List
Movie List
DivX(R) VOD
Game
The available entertainment settings are described in the following.
Setting
Description
1 Press SETTINGS and the Navigation buttons to scroll to LOCK.
Photo List
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
Views image files(photos) on TV which
are stored on USB device. (See p. 20)
Music List
Plays back music files on TV which are
stored on USB device. (See p. 21)
Movie List
Plays movie files on TV which are
stored on usb device. (See p. 22)
DivX(R) VOD
Views the registration code of your TV.
(See p. 23)
LOCK settings
3 When you return to the previous menu, press
BACK.
* Image shown may differ from your TV.
LOCK
Lock System
Set Password
Block Programme
Input Block
28
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
Move
Move
: Off
OK
OK
Game
(Depending on model)
Plays game contents on your TV.
Teletext
Special teletext function
Index
The teletext decoder of this TV can support the SIMPLE and FASTEXT
systems. SIMPLE (standard teletext) consists of a number of pages
which are selected by directly entering the corresponding page number.
FASTEXT are more modern methods allowing quick and easy selection
of teletext information.
Switch On/Off
Press the TEXT button to switch to teletext. The initial page or last page
viewed appears on the screen.
Two page numbers, TV station name, date and time are displayed on
the screen headline. The first page number indicates your selection,
while the second shows the current page displayed.
Press the TEXT button to switch off teletext. The previous mode
reappears.
Simple text
Page selection
1 Enter the desired page number as a three digit number with the
Number buttons. If during selection you press a wrong number, you
must complete the three digit number and then re-enter the correct
page number.
Select the each index page.
ENGLISH
* This feature is not available in all countries.
Teletext is a free service broadcast by most TV stations which gives upto-the minute information on news, weather, television programmes,
share prices and many other topics.
Time
When viewing a TV programme, select this menu to display the time at
the top right hand corner of the screen.
In the teletext mode, press this button to select a sub page number. The
sub page number is displayed at the bottom of the screen. To hold or
change the sub page, press the Red/Green,
or Number buttons.
Hold
Stops the automatic page change which will occur if a teletext page
consists of 2 or more sub pages.
The number of sub pages and the sub page displayed is, usually, shown
on the screen below the time. When this menu is selected the stop
symbol is displayed at the top left-hand corner of the screen and the
automatic page change is inactive.
Reveal
Select this menu to display concealed information, such as solutions to
riddles or puzzles.
Update
Displays the TV picture on the screen while waiting for a new teletext
page. The display will appear at the top left hand corner of the screen.
When the updated page is available then display will change to the
page number. Select this menu again to view the updated teletext
page.
2 The
button can be used to select the preceding or
following page.
Fastext
The teletext pages are colour coded along the bottom of the screen and
are selected by pressing the corresponding coloured button.
Page selection
1 Press the INDEX button to select the index page.
2 You can select the pages which are colour coded along the bottom
line with corresponding coloured buttons.
3 AS with SIMPLE teletext mode, you can select a page by entering its
three digit page number with the Number buttons in FASTEXT mode.
4 The
button can be used to select the preceding or
following page.
29
Troubleshooting
Specifications
Cannot control the TV with the remote control.
ENGLISH
• Check the remote control sensor on the product and try again.
• Check if there is any obstacle between the product and the remote
control.
• Check if the batteries are still working and properly installed (
to , to ).
Environment
condition
No image display and no sound is produced.
• Check if the product is turned on.
• Check if the power cord is connected to a wall outlet.
• Check if there is a problem in the wall outlet by connecting other
products.
The TV turns off suddenly.
• Check the power control settings. The power supply may be
interrupted.
• Check if the Automatic Standby (Depending on model) / Sleep
Timer / Off Time is activated in the TIME settings.
• If there is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
• If On Time is enabled, the TV will be turned on at the specified
time. If you do not operate the TV for two hours, the TV will be
turned off automatically. To disable this function, use your remote
control to go to SETTINGS TIME Auto Off(On Time)
(Depending on model) Off.
When connecting to the PC (HDMI/RGB), ‘No signal’ or ‘Invalid Format’
is displayed.
• Turn the TV off/on using the remote control.
• Reconnect the HDMI/RGB cable.
• Restart the PC with the TV on.
30
Operating
Temperature
0 °C to 40 °C
Operating
Humidity
Less than 80 %
Storage
Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Analogue TV
(Depending on Country)
Television system
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
Programme coverage
VHF, UHF, CATV
Maximum number of
storable programmes
200
External antenna
impedance
75 Ω
HDMI-DTV supported mode
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
720 x 480
31.469
31.5
59.94
60.00
720 x 576
31.25
50.00
1280 x 720
44.96
45
37.5
59.94
60.00
50.00
1920 x 1080
28.125
33.72
33.75
56.25
67.43
67.5
27
33.75
26.97
33.716
50.00
59.94
60.00
50.00
59.94
60.00
24.00
30.00
23.97
29.976
RGB-PC supported mode
AC/DC Adapter
(Depending on model)
(Only India)
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
640 x 480
31.469
59.94
800 x 600
37.879
60.317
1024 x 768
48.363
60.0
1280 x 720
47.77
59.85
1152 x 864
54.34
60.05
24LH45**
1366 x 768
47.71
59.79
Manufacturer : Honor
Model : ADS-45EI-19 19032GPI
28LH45**
Manufacturer : APD
Model : WA-40D19FI
Input: AC 100-240 V~ 50/60 Hz
Output: 19 V 2.1 A
NOTE
Manufacturer : APD
Model : WA-32C19FI
• The optimal display resolution
- 1366 x 768 @ 60 Hz.
• The optimal timing in each mode is vertical frequency 60 Hz.
Input: AC 100-240 V~ 50/60 Hz
Output: 19 V 1.7 A
Component port connecting information
(Except for India)
(Depending on model)
Component ports on the TV
Video output ports on DVD player
ENGLISH
Manufacturer : Honor
Model : ADS-45EI-19 19040GPI
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Signal
Component
480i / 576i
O
480p / 576p
O
720p / 1080i
O
1080p
O
(Only 50 Hz / 60 Hz )
28LH45**
Manufacturer : Lien Chang
Model : LCAP16B-E, LCAP16B-A, LCAP21C
Manufacturer : Honor
Model : ADS-45EI-19 19040GPI,
ADS-45FSN-19 19040GPG,
ADS-45FSN-19 19040GPCU,
ADS-40LSI-19-2 19040G,
ADS-45SN-19-3 19040G
Manufacturer : APD
Model : WA-40D19FI, DA-40I19
Input: AC 100-240 V~ 50/60 Hz
Output: 19 V 2.1 A
24LH45**
Manufacturer : Lien Chang
Model : LCAP16A-E, LCAP16A-A, LCAP21A
Manufacturer : Honor
Model : ADS-45EI-19 19032GPI,
ADS-40FSG-19 19032GPG,
ADS-40FSG-19 19032GPCU,
ADS-40LSI-19-2 19032G,
ADS-40SG-19-3 19032G
Manufacturer : APD
Model : WA-32C19FI, DA-32F19
Input: AC 100-240 V~ 50/60 Hz
Output: 19 V 1.7 A
31
Regulatory
ENGLISH
WARNING!
Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to
children, can be avoided by taking simple precautions such as:
• • • • Using cabinets or stands recommended by the manufacturer of the television set.
Only using furniture that can safely support the television set.
Ensuring the television set is not overhanging the edge of the supporting furniture.
Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television
set to a suitable support.
• Not placing the television set on cloth or other materials that may be located between the television set and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the television set or its controls.
If your existing television set is being retained and relocated, the same considerations as above should be applied.
Symbols
Refers to alternating current(AC).
Refers to direct current(DC).
Refers to class II equipment.
Refers to stand-by.
Refer to “ON” (power).
Refers to dangerous voltage.
32
ENGLISH
33
Record the model number and serial number
of the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
MODEL
SERIAL
Download PDF