LG | 24LJ470A | LG 24LJ470A Owner’s Manual

OWNER’S MANUAL
Safety and Reference
LED TV*
* Disclaimer
LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and
retain it for future reference.
www.lg.com
MFL69446179
P/NO : MFL69446179 (1702-REV00)
India region only. (Below sentence is not applicable for above 1920 X 1080 resolution TV models.)
ATTENTION:
ENGLISH
This product is qualified for the BEE Star rating in the ‘Home’ Mode.
The Objectives of Star Labeling Program is designed to promote energy efficient products and practices.
When the television is initially set up, it is designed to meet the BEE Star Labeling requirements while maintaining optimum picture quality.
• Changes to certain functionalities of this television (TV Guide, Picture/sound etc) may change the power consumption.
• Depending upon such changed setting (eg., Retail mode), the power consumption may vary which possibly could exceed the stated
energy consumption.
To reset the television to Star rating qualified settings, select ‘Home’ mode from the initial set-up procedure in ‘factory settings’ under the
‘Set-up’ menu.
2
ENGLISH
3
Warning! Safety instructions
ENGLISH
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
• Do not place the TV and/or remote control in the following
environments:
- A location exposed to direct sunlight
- An area with high humidity such as a bathroom
- Near any heat source such as stoves and other devices that
produce heat
- Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil
- An area exposed to rain or wind
- Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or
product deformation.
• Do not place the product where it might be exposed to dust. This
may cause a fire hazard.
• Mains Plug is the TV connecting/disconnecting device to AC
mains electric supply. This plug must remain readily attached and
operable when TV is in use.
• Do not touch the power plug with wet hands. Additionally, if the
cord pin is wet or covered with dust, dry the power plug completely
or wipe dust off. You may be electrocuted due to excess moisture.
• Make sure to connect Mains cable to compliant AC mains socket
with Grounded earth pin. (Except for devices which are not
grounded on earth.) Otherwise possibility you may be electrocuted
or injured.
• Insert power cable plug completely into wall socket otherwise if
not secured completely into socket, fire ignition may break out.
4
• Ensure the power cord does not come into contact with hot objects
such as a heater. This may cause a fire or an electric shock hazard.
• Do not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in fire or electric shock.
• Bend antenna cable between inside and outside building to
prevent rain from flowing in. This may cause water damaged inside
the Product and could give an electric shock.
• When mounting TV onto wall make sure to neatly install and
isolate cabling from rear of TV as to not create possibility of electric
shock /fire hazard.
• Do not plug too many electrical devices into a single multiple
electrical outlet. Otherwise, this may result in fire due to overheating.
• Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the
product.
• Keep the anti-moisture packing material or vinyl packing out of the
reach of children. Anti-moisture material is harmful if swallowed.
If swallowed by mistake, force the patient to vomit and visit the
nearest hospital. Additionally, vinyl packing can cause suffocation.
Keep it out of the reach of children.
• Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
• Dispose of used batteries carefully to ensure that a small child
does not consume them. Please seek Doctor- Medical Attention
immediately if child consumes batteries.
• Do not insert any metal objects/conductors (like a metal chopstick/
cutlery/screwdriver) into the end of power cable while the power
plug is plugged into wall socket. Additionally, do not touch the
power plug right after unplugging from the wall socket. You may
be electrocuted.
• Do not put or store inflammable substances near the product.
There is a danger of combustion/explosion or fire due to careless
handling of the inflammable substances.
• Do not drop metallic objects such as coins, hair pins, chopsticks
or wire into the product, or inflammable objects such as paper
and matches. Children must pay particular attention. Electrical
shock, fire or injury can occur. If a foreign object is dropped into the
product, unplug the power cord and contact the service centre.
• Do not spray water on the product or scrub with an inflammable
substance (thinner or benzene). Fire or electric shock accident can
occur.
• Do not allow any impact, shock or any objects to fall into the unit,
and do not drop anything onto the screen. You may be injured or
the product can be damaged.
• Never touch this product or antenna during a thunder or lighting
storm.
You may be electrocuted.
CAUTION
• If you intend to mount the product to a wall, attach VESA standard
mounting interface (optional parts) to the back of the product.
When you install the set to use the wall mounting bracket
(optional parts), fix it carefully so as not to drop.
• Only use the attachments / accessories specified by the
manufacturer.
• When installing the antenna, consult with a qualified service
technician. If not installed by a qualified technician, this may
create a fire hazard or an electric shock hazard.
• We recommend that you maintain a distance of at least 2 to 7
times the diagonal screen size when watching TV. If you watch TV
for a long period of time, this may cause blurred vision.
• Only use the specified type of battery. This could cause damage to
the remote control.
• Do not mix new batteries with old batteries. This may cause the
batteries to overheat and leak.
• Batteries should not be exposed to excessive heat. For example,
keep away from direct Sunlight, open fireplace and electric
heaters.
• Signal from Remote Control can be interrupted due to external/
internal lighting eg Sunlight, fluorescent lighting. If this occurs
turn off lighting or darken viewing area.
• When connecting external devices such as video game consoles,
make sure the connecting cables are long enough. Otherwise,
the product may fall over, which may cause injury or damage the
product.
• Do not turn the product On/Off by plugging-in or unplugging
the power plug to the wall outlet. (Do not use the power plug for
switch.) It may cause mechanical failure or could give an electric
shock.
• Please follow the installation instructions below to prevent the
product from overheating.
- The distance between the product and the wall should be more
than 10 cm.
- Do not install the product in a place with no ventilation (e.g., on
a bookshelf or in a cupboard).
- Do not install the product on a carpet or cushion.
- Make sure the air vent is not blocked by a tablecloth or curtain.
This may result in fire.
• Take care not to touch the ventilation openings when watching
the TV for long periods as the ventilation openings may become
hot. This does not affect the operation or performance of the
product.
ENGLISH
• Never touch the wall outlet when there is leakage of gas, open the
windows and ventilate. It may cause a fire or a burn by a spark.
• Do not disassemble, repair or modify the product at your own
discretion. Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
• If any of the following occur, unplug the product immediately and
contact your local service centre.
- The product has been damaged
- Foreign objects have entered the product
- The product produced smoke or a strange smell
This may result in fire or electric shock.
• Unplug the TV from AC mains wall socket if you do not intend to
use the TV for a long period of time. Accumulated dust can cause
fire hazard and insulation deterioration can cause electric leakage/
shock/fire.
• Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the
apparatus.
• Do not install this product on a wall if it could be exposed to oil or
oil mist. This may damage the product and cause it to fall.
• If water enters or comes into contact with TV, AC adapter or power
cord please disconnect the power cord and contact service centre
immediately. Otherwise, this may result in electric shock or fire.
• Only use an authorized AC adapter and power cord approved by
LG Electronics. Otherwise, this may result in fire, electric shock,
malfunction or product deformation.
• Never Disassemble the AC adapter or power cord. This may result
in fire or electric shock.
• Be careful in handling the adapter to prevent any external shocks
to it. An external shock may cause damage to the adapter.
• Make sure the power cord is connected securely to the power plug
on the TV.
• Install the product where no radio wave occurs.
• There should be enough distance between an outside antenna and
power lines to keep the former from touching the latter even when
the antenna falls. This may cause an electric shock.
• Do not install the product on places such as unstable shelves or
inclined surfaces. Also avoid places where there is vibration or
where the product cannot be fully supported. Otherwise, the
product may fall or flip over, which may cause injury or damage
to the product.
• If you install the TV on a stand, you need to take actions to prevent
the product from overturning. Otherwise, the product may fall
over, which may cause injury.
5
ENGLISH
• Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with
an exact replacement part by an authorized servicer.
• Prevent dust collecting on the power plug pins or outlet. This may
cause a fire hazard.
• Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon.
Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
• Do not press strongly upon the panel with a hand or sharp object
such as nail, pencil or pen, or make a scratch on it, as it may
cause damage to screen.
• Avoid touching the screen or holding your finger(s) against it for
long periods of time. Doing so may produce some temporary or
permanent distortion/damage to screen.
• As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this
unit by SWITCH.
• When unplugging the cable, grab the plug and unplug it, by
pulling at the plug.
• Don’t pull at the cord to unplug the power cord from the power
board, as this could be hazardous.
• When moving the product, make sure you turn the power off first.
Then, unplug the power cables, antenna cables and all connecting
cables.
The TV set or power cord may be damaged, which may create a fire
hazard or cause electric shock.
• When moving or unpacking the product, work in pairs because the
product is heavy. Otherwise, this may result in injury.
• Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
• Do not use high voltage electrical goods near the TV (e.g. electric
mosquito-swatter). This may result in product malfunction.
• When cleaning the product and its components, unplug the power
first and wipe it with a soft cloth. Applying excessive force may
cause scratches or discolouration. Do not spray with water or wipe
with a wet cloth. Never use glass cleaner, car or industrial shiner,
abrasives or wax, benzene, alcohol etc., which can damage the
product and its panel. Otherwise, this may result in fire, electric
shock or product damage (Deformation, corrosion or breakage).
6
Preparing
NOTE
• Image shown may differ from your TV.
• Your TV’s OSD (On Screen Display) may differ slightly from that
shown in this manual.
• The available menus and options may differ from the input source
or product model that you are using.
• New features may be added to this TV in the future.
• The items supplied with your product may vary depending on the
model.
• Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
• For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV’s USB port.
B
B
A
A
*A <
= 10 mm
*B <
= 18 mm
• Use a certified cable with the HDMI logo attached.
• If you do not use a certified HDMI cable, the screen may not display
or a connection error may occur. (Recommended HDMI cable types)
- High-Speed HDMI®/™ cable (3 m or less)
- High-Speed HDMI®/™ cable with Ethernet (3 m or less)
CAUTION
• Do not use any unapproved items to ensure the safety and product
life span.
• Any damage or injuries caused by using unapproved items are not
covered by the manufacturer’s warranty.
• Some models have a thin film attached on to the screen and this
must not be removed.
• When attaching the stand to the TV set, place the screen facing
down on a cushioned table or flat surface to protect the screen
from scratches.
• Make sure that the screws are inserted correctly and fastened
securely. (If they are not fastened securely enough, the TV may tilt
forward after being installed.) Do not use too much force and over
tighten the screws; otherwise screw may be damaged and not
tighten correctly.
• Make sure to wring any excess water or cleaner from the cloth.
• Do not spray water or cleaner directly onto the TV screen.
• Make sure to spray just enough of water or cleaner
onto a dry cloth to wipe the screen.
• When cleaning the product, be careful not to allow
any liquid or foreign objects to enter the gap between
the upper, left or right side of the panel and the guide
panel. (Depending on model)
Maintenance
Cleaning your TV
Screen, frame, cabinet, and stand
To remove dust or light dirt, wipe the surface with a dry, clean, and
soft cloth.
To remove major dirt, wipe the surface with a soft cloth dampened
in clean water or a diluted mild detergent. Then wipe immediately
with a dry cloth.
• Avoid touching the screen at all times, as this may result in
damage to the screen.
• Do not push, rub, or hit the surface with your fingernail or a sharp
object, as this may result in scratches on the screen and image
distortions.
• Do not use any chemicals as this may damage the product.
• Do not spray liquid onto the surface. If water enters the TV, it may
result in fire, electric shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
Lifting and moving the TV
(*Image may very depending on models)
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
• It is recommended to move the TV in the box or packing material
that the TV originally came in.
• Before moving or lifting the TV, disconnect the power cord and
all cables.
• When holding the TV, the screen should face away from you to
avoid damage.
ENGLISH
Clean your TV regularly to keep the best performance and to extend
the product lifespan.
• Make sure to turn the power off and disconnect the power cord
and all other cables first.
• When the TV is left unattended and unused for a long time,
disconnect the power cord from the wall outlet to prevent possible
damage from lightning or power surges.
• When transporting a large TV, there should be at least 2 people.
• When transporting the TV by hand, hold the TV as shown in the
following illustration.
• When transporting the TV, do not expose the TV to jolts or
excessive vibration.
• When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right.
• Do not apply excessive pressure to cause flexing /bending of frame
chassis as it may damage screen.
• When handling the TV, be careful not to damage the protruding
buttons.
CAUTION
• Avoid touching the screen at all times, as this may result in damage
to the screen.
• Do not move the TV by holding the cable holders, as the cable holders
may break, and injuries and damage to the TV may occur.
Setting up the TV
CAUTION
• Do not carry the TV upside-down by holding the stand body (or stand
base) as this may cause it to fall off, resulting in damage or injury.
• When attaching the stand to the TV set, place the screen facing down
on a cushioned table or flat surface to protect the screen from scratches.
• When detaching the stand to the TV set, place the screen facing down
on a cushioned table or flat surface to protect the screen from scratches.
• If you dont fasten the screw tightly, TV will fall down and get
damaged.
• Tighten the screws firmly to prevent the TV from tilting forward.
Do not over tighten.
• Lift up the latch at the bottom of the stand base and detach the stand
base from the TV.
• Hold the top and bottom of the TV frame firmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
7
ENGLISH
Using the button
Adjusting the menu
(*Image may very depending on models)
(Depending on model)
You can simply operate the TV functions, using the button.
When the TV is turned on, press the button one time. You can adjust
the Menu items using the button.
Turns the power off.
Accesses the settings menu.
Clears on-screen displays and returns to TV viewing.
Changes the input source.
Mounting on a table
(*Image may very depending on models)
1 Lift and tilt the TV into its upright position on a table.
• Leave a 10 cm (minimum) space from the wall for proper
ventilation.
10 cm
Basic functions
When the TV is turned off,
Place your finger on the
Joystick button and
Press it once and release it.
When
the TV is turned on,
Power On (Press) place your
finger on the
Power Off
joystick button and press it
(Press and hold)1 once for few seconds and
release it. (However, if the
Menu button is on the
screen, pressing and
holding the joystick button
will let you exit the Menu.
If you place your finger over
Volume Control the joystick button and move
it left or right, you can adjust
the volume level you want.
Programmes
Control
If you place your finger over
the Joystick button and move
it forward or backward, you
can scrolls through the saved
programmes you want.
1 If the Menu button is on the screen, pressing and holding the button
will let you exit the Menu.
NOTE
• If you press the joystick button first, you may not adjust the
volume level and saved programmes.
CAUTION
• When your finger over the joystick button and push it to the up,
down, left or right, be careful not to press the joystick button.
8
10 cm
10 cm
10 cm
10 cm
2 Connect the AC-DC Adapter and Power Cord to a wall outlet.
CAUTION
• Do not place the TV near or on sources of heat, as this
may result in fire or other damage.
WARNING
• Do not apply foreign substances (oils, lubricants, etc.)
to the screw parts when assembling the product.
(Doing so may damage the product.)
• If a television is not positioned in a sufficiently stable
location, it can be potentially hazardous due to falling.
Many injuries, particularly to children, can be avoided
by taking simple precautions such as:
- Using cabinets or stands recommended by the
manufacturer of the television.
- Only using furniture that can safely support the television.
- Ensuring the television is not overhanging the edge
of the supporting furniture.
- Not placing the television on tall furniture (for
example, cupboards or bookcases) without
anchoring both the furniture and the television to a
suitable support.
- Not standing the televisions on cloth or other
materials placed between the television and supporting furniture.
- Educating children about the dangers of climbing
on furniture to reach the television or its controls.
Using the kensington security system
Mounting on a wall
(*Image may very depending on models)
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the floor. When you attach the TV to other building materials, please
contact qualified personnel. LG recommends that wall mounting be
performed by a qualified professional installer. We recommend the use
of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with
cables connected. When you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is adequately secured to the
wall with enough space to allow connectivity to external devices. It is
advised to connect all the cables before installing fixed wall mounts.
ENGLISH
This feature may vary depending on model.
• Image shown may differ from your TV.
The Kensington security system connector is located at the rear of
the TV. For more information of installation and using, refer to the
manual provided with the Kensington security system or visit
http://www.kensington.com. Connect the Kensington security system
cable between the TV and a table.
10 cm
10 cm
NOTE
10 cm
• The Kensington security system is optional. You can obtain
additional accessories from most electronics stores.
Securing the TV to a wall
(Feature may very depending on model)
10 cm
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described in
the following table.
For proper ventilation, allow a clearance of 100 mm on each side and
from the wall. Detailed installation instructions are available from
your dealer, see the optional Tilt Wall Mounting Bracket Installation
and Setup Guide.
If you intend to mount the TV to a wall, attach Wall mounting
interface (optional parts) to the back of the TV. When you install
the TV using the wall mounting interface (optional parts), attach it
carefully so it will not drop.
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
• If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear
of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the flat surface.
CAUTION
• Make sure that children do not climb on or hang on the TV.
NOTE
• Use a platform or cabinet that is strong and large enough to
support the TV securely.
• Brackets, bolts and ropes are not provided. You can obtain
additional accessories from your local dealer.
1
If you use screw longer than standard, the TV might be damaged
internally.
2
If you use improper screw, the product might be damaged and
drop from mounted position. In this case, LG Electronics is not
responsible for it.
CAUTION
• Disconnect the power cord first, and then move or install the TV.
Otherwise electric shock may occur.
• Remove the stand before installing the TV on a wall mount by
performing the stand attachment in reverse.
• The Screw Cover will protect the opening from accumulating dust
and dirty.
• If you install the TV on a ceiling or slanted wall, it may fall and
Result in severe injury. Use an authorized LG wall mount and
contact the local dealer or qualified personnel.
• Do not over tighten the screws as this may cause damage to the TV
And void your warranty.
• Use the screws and wall mounts that meet the VESA standard. Any
Damages or injuries by misuse or using an improper accessory are
Not covered by the manufacture’s warranty.
9
Separate purchase (Wall mounting bracket)
ENGLISH
Model
Wall Mount (A x B) (mm)
Standard screw
Number of screws
24LJ47**
75 x 75
M4 x L10
4
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external device’s
connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, gaming devices, and other external
devices.
A
B
CAUTION
• Remove the stand before installing the TV on a wall mount by
performing the stand attachment in reverse.
• Screw length from outer surface of back cover should be under 8mm.
NOTE
• Do not use a sharp object when you detached the cable cover. This
could damage the cable or the cabinet. It may also cause personal
harm.
• Use the screws that are listed on the VESA standard screw
specifications.
• The wall mount kit includes an installation manual and necessary
parts.
• The wall mount bracket in not provided along with the TV set.
• The length of screws may differ depending on the wall mount.
Make sure to use the proper length.
• For more information, refer to the manual supplied with the wall
mount.
Wall mount Pad
• The external device connection may differ from the model.
• Connect external devices to the TV regardless of the order of the
TV port.
• If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder
or VCR. For more information of recording, refer to the manual
provided with the connected device.
• Refer to the external equipment’s manual for operating
instructions.
• If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
NOTE
• Use a signal splitter to use more than 2 TVs.
• If the image quality is poor, install a signal amplifier properly to
improve the image quality.
• If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
• An antenna cable and converter are not supplied.
Adapter connection
CAUTION
Back Cover
Wall mount Pad
Back Cover
Standard screw
• Please be sure to connect the TV to the AC-DC power adapter
before connecting the TV’s power plug to a wall power outlet.
Other connections
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
: M4 x L10
Max. 8 mm
10
Connections (notifications)
• Supported HDMI Audio format :
Dolby Digital (32 kHz, 44,1 kHz, 48 kHz),
PCM (32 kHz, 44.1 kHz, 48 kHz, 88 kHz, 96 kHz, 176 kHz, 192 kHz)
Remote control
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
CAUTION
• Do not mix old and new batteries, as this may damage the
remote control.
• In Analogue TV and some countries, some remote control buttons
may not work.
• The remote control will not be included for all sales market.
Make sure to point the remote control toward the remote control sensor
on the TV.
ENGLISH
To replace batteries, open the battery cover, replace batteries (1.5
V AAA) matching the and ends to the label inside the
compartment, and close the battery cover. To remove the batteries,
perform the installation actions in reverse.
Switches the BOLLYWOOD sound mode.
Changes the input source.
Number buttons Enters numbers.
Accesses the saved programme list.
Returns to the previously viewed programme.
Adjusts the volume level.
Accesses your favourite programme list.
Selects the sound output.
Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next screen.
,
,
,
,
,
Teletext buttons (
) These buttons are used for teletext.
Accesses the main menus.
Navigation buttons (up/down/left/right) Scrolls through
menus or options.
Selects menus or options and confirms your input.
Returns to the previous level.
Clears on-screen displays and returns to TV viewing.
) Controls media contents.
Control buttons (
Coloured buttons
These access special
functions in some menus.
Licenses
Supported licenses may differ by model. For more information about
licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. Dolby, Dolby
Vision, Dolby Audio, and the double-D symbol are trademarks of
Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
This DivX Certified® device has passed rigorous testing to ensure it
plays DivX® video.
(POWER) Turns the TV on or off.
Returns to the TV viewing from any mode.
Accesses the Quick menus.
Used to start or stop Mosquito Away operation.
* The Mosquito Away performance can be different depending on
the customer’s environment. For detail, refer Disclaimer. (See p.
31)
To play purchased DivX movies, first register your device at vod.divx.
com. Find your registration code in the DivX VOD section of your
device setup menu.
DivX Certified® to play DivX® video up to HD 1080p, including
premium content.
DivX®, DivX Certified® and associated logos are trademarks of DivX,
LLC and are used under license.
Covered by DivX Patents 7,295,673; 7,515,710; RE45,052; and others
available at [www.divx.com/patents].
11
Open source software
notice information
Watching TV
1 In Standby mode, press
ENGLISH
To obtain the source code under GPL, LGPL, MPL, and other open source
licenses, that is contained in this product, please visit http://opensource.
lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date
on which you purchased the product.
2 Press
(POWER) to turn the TV on.
INPUT and select TV.
3 To turn the TV off, press
mode.
(POWER). The TV switches to Standby
Managing programmes
Automatically setting up programme
Use this to automatically find and store all available programmes.
Watching TV
1 Press SETTINGS and the Navigation buttons to scroll to SETUP and
press
.
Turning the TV on for the first time
2 Press the Navigation buttons to scroll to Auto Tuning and press
.
When you turn the TV on for the first time, the Initial setting screen
appears. Select a language and customize the basic settings.
3 Press the Navigation buttons to scroll to Start and select Start to
begin auto tuning. The TV scans and saves available programmes
automatically.
1 Connect the power cord to a power outlet. The Power indicator turns
red and the TV switches to Standby mode.
2 In Standby mode, press the power button on the remote control or
local key to turn the TV on. The Initial setting screen appears if you
turn the TV on for the first time.
• You can also access Factory Reset by accessing OPTION in the
main menu.
3 Follow the on-screen instructions to customize your TV settings
according to your preferences.
Menu Language
Selects a language to display.
Mode Setting
Selects Home Use for the home
environment.
Time Setting
Sets the time.
Auto Tuning
Scans and saves available
programmes automatically.
4 When you return to the previous menu, press
.
Manually setting up programme
Manual Tuning lets you manually tune and arrange the stations in
whatever order you desire.
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
2 Press the Navigation buttons to scroll to Manual Tuning.
3 Press the Navigation buttons to scroll to Storage.
4 Press the Navigation buttons or Number buttons to select the desired
programme number.
5 Press the Navigation buttons to scroll to System.
6 Press the Navigation buttons to scroll to TV System.
7 Press the Navigation buttons to scroll to Band.
• To display images in the best quality for your home environment,
select Home Use.
• Store Demo is suitable for the retail environment.
• If you select Store Demo, any customized settings will switch
back to the default settings of Store Demo in 5 minutes.
4 When the basic settings are complete, press the
.
• If you do not complete the Initial setting, it will appear whenever
the TV turns on.
• Disconnect the power cord from the power outlet when you do not
use the TV for a long period of time.
5 To turn the TV off, press the power button on the remote control.
12
8 Press the Navigation buttons to scroll to V/UHF or Cable.
9 Press the Navigation buttons to scroll to Channel.
10 Press the Navigation buttons and then select the desired Channel
number with the Navigation buttons or Number buttons.
11 Press the Navigation buttons to scroll to Search.
12 Press the Navigation buttons to scroll and start Searching.
13 Press the OK
to store it.
14 When you return to the previous menu, press
• To store another programme, repeat steps 3 to 13.
.
Assigning a station name
You can assign a station name with five characters to each programme
number.
1 Press LIST to access the programme list.
2 Press the Navigation buttons to scroll to Manual Tuning.
2 Press the Navigation buttons to select to desired programme and
press OK .
3 Press the Navigation buttons to scroll to Name.
3 When you return to the previous menu, press LIST.
• You may find some blue programmes. They have been set up to be
skipped by auto programming or in the programme edit mode.
• Some programmes with the programme number shown in the
programme list indicate there is no station name assigned.
4 Press the Navigation buttons to scroll to select the position and
make your choice of the second character, and so on. You can use the
alphabet A to Z, the number 0 to 9, +/ -, and blank and press OK .
5 Press the OK
to store it.
6 When you return to the previous menu, press
.
Using additional options
Fine Tuning
Normally fine tuning is only necessary if reception is poor.
Adjusting aspect ratio
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
Resize an image to view at its optimal size by pressing Q.MENU or
accessing Aspect Ratio in the PICTURE menu.
2 Press the Navigation buttons to scroll to Manual Tuning.
3 Press the Navigation buttons to scroll to Fine.
• The available ratio varies depending on the input source.
4 Press the Navigation buttons to fine tune for the best picture and
sound.
5 Press the OK
ENGLISH
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
Selecting a programme on the programme
list
- 16:9 : Resizes images to fit the screen width.
to store it.
6 When you return to the previous menu, press
.
Editing your programme list
When a programme number is skipped, it means that you will be
button during TV viewing.
unable to select it using
If you wish to select the skipped programme, directly enter the
programme number with the NUMBER buttons or select it in the
Programme edit menu.
- Just Scan : Displays video images in the original size without
removing parts of the edge of the image. (This function works
in Component/HDMI (720p / 1080i / 1080p) Mode.)
This function enables you to skip the stored programmes.
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
2 Press the Navigation buttons to scroll to Programme Edit.
• If you select Just Scan, you may see image noises at the edge of
the original signal.
3 Edit programmes using the following buttons.
Button
Description
- Original : When your TV receives a wide screen signal it will
automatically change to the picture format broadcasted.
Deletes a programme.
Red button
Press the Red button twice. The selected
programme is deleted, all the following
programmes are shifted up one position.
(4:3
4:3)
(16:9
16:9)
Moves a programme.
Yellow button
Blue button
Press the Yellow button again to release this
function.
-
Selects a programme number to be skipped. Press
the Blue button again to release the skipped
programme.
4 When you return to the previous menu, press
.
13
- 4:3 : Resizes images to the previous standard 4:3.
Using the input list
Selecting an input source
INPUT to access the input sources.
1 Press
ENGLISH
- 14:9 : You can view a picture format of 14:9 or a general TV
programme in the 14:9 mode.
• The connected device displays on each input source.
2 Press the Navigation buttons or input button to scroll to one of the
input sources and press OK .
* Image shown may differ from your TV.
Input List
RGB-PC
AV
HDMI
Input Label
- Zoom : Formats an image to fit the screen width. The top and
bottom of the image may not appear.
• If you enlarge or reduce an image, the image may be distorted.
Using the input list.
14
Exit
Input source
Description
Antenna
Watch TV over the air and cable broadcast.
AV
Watch video from a VCR or other external
devices.
RGB-PC
- Cinema Zoom 1 : Formats an image to the cinemascope ratio,
2.35:1.
To change the ratio of the cinema zoom, press or and its
range is from 1 to 16.
Antenna
HDMI
View a PC display on the screen.
Watch video from a HTS or other high
definition devices.
Entertainment
(Depending on model)
* Image shown may differ from your TV.
Connect USB storage devices (USB memory) to the TV and use
multimedia features (See “Browsing files” on page 15-16).
USB IN
Connect a USB flash memory or USB memory card reader to the TV as
shown on the following illustration.
To disconnect a USB storage device, make sure to end the connection
properly to prevent damages to the TV or files.
1 Press Q.MENU to access the quick menus.
2 Press the Navigation buttons to scroll to Eject and press OK
.
3 Disconnect the USB storage device only when the message says that
it is safe to remove.
CAUTION
• Do not turn the TV off or remove a USB storage device while the USB
storage device is connected to the TV, as this could result in loss of
files or damage to the USB storage device.
• Back up your files saved on a USB storage device frequently, as you
may lose or damage the files and this may be not covered by the
manufacturer’s warranty.
Tips for using USB storage devices
• Only a USB storage device is recognizable.
• If the USB storage device is connected through a USB hub, the
device is not recognizable.
• A USB storage device using an automatic recognition programme
may not be recognized.
• A USB storage device which uses its own driver may not be
recognized.
• The recognition speed of a USB storage device may depend on
each device.
• Please do not turn off the TV or unplug the USB device when
the connected USB storage device is working. When such device
is suddenly separated or unplugged, the stored files or the USB
storage device may be damaged.
ENGLISH
Connecting USB storage devices
• Please do not connect the USB storage device which was artificially
manoeuvred on the PC. The device may cause the product to
malfunction or fail to be played. Never forget to use only a USB
storage device which has normal music files, image files or movie
files.
• Please use only a USB storage device which was formatted as a
FAT16, FAT32, NTFS file system.
• Please connect a USB storage device with the cable offered by the
device maker.
• Some USB storage devices may not be supported or operated
smoothly.
• Be sure to back up important files since data stored in a USB
memory device may be damaged. We will not be responsible for
any data loss.
• If a USB memory device is connected to a USB multi-card reader, its
volume data may not be detected.
• If the USB memory device does not work properly, disconnect and
reconnect it.
• How fast a USB memory device is detected differs from device to
device.
• The recommended capacity is 1 TB or less for a USB external hard
disk and 32 GB or less for USB memory.
• Any device with more than the recommended capacity may not
work properly.
• USB storage devices below USB 2.0 are supported as well. But they
may not work properly in the movie list.
• Maximum of 999 folders or files can be recognized under one
folder.
• If there are a lot of folders or files all within one folder, the device
may not be able to access these properly.
• For external USB HDDs, it is recommended that you use devices
with a rated voltage of less than 5 V and a rated current of less
than 0.5A.
Browsing files
Access the photo, music, or movie lists and browse files.
1 Connect a USB storage device.
2 Press SETTINGS to access the main menus.
3 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
4 Press Navigation buttons to scroll to PHOTO LIST, MUSIC LIST or
MOVIE LIST and press OK .
* Image shown may differ from your TV.
PHOTO LIST
MUSIC LIST
MOVIE LIST
15
3
PHOTO LIST
Page 1/1
DriveA
GUU.JPG
Type
No Marked
Up Folder
ENGLISH
2
3872 x 2592, 2604 KB
1
Supported file format
4
Up Folder
KY103
09/15/2016
KY101
04/03/2016
KY104
10/12/2016
KY102
09/03/2016
KY105
11/27/2016
GUU
11/27/2016
JMJ005
11/27/2016
JMJ002
11/27/2016
JMJ006
11/27/2016
JMJ003
11/27/2016
JMJ007
11/27/2016
JMJ004
11/27/2016
JMJ008
11/27/2016
ꔂ Move
ꔵ Move Page
ꔉ PopUp Menu
ꘂ Mark
Page 1/1
Baseline : 64 pixel (W) x 64 pixel (H) - 15360 pixel
(W) x 8640 pixel (H)
• You can play JPEG files only.
• Non-supported files are displayed in the form
of predefined icon.
Music
Duration
5
2
ꕗ
• Sampling rate MPEG1 Layer3 : 32 kHz, 44.1
kHz, 48 kHz
• Sampling rate MPEG2 Layer3 : 16 kHz, 22.05
kHz, 24 kHz
• Sampling rate MPEG2.5 Layer3 : 8 kHz, 11.025
kHz, 12 kHz
Up Folder
ꔉ PopUp Menu
ꘂ Mark
3
MOVIE LIST
Top Folder
DriveA
6
ꔵ Move Page
Option
Exit
4
Page 1/1
Movie
No Marked
Title
Duration
DriveA
5
2
4 folder(s), 2 file(s)
Up Folder
ꔂ Move
ꔉ PopUp Menu
ꘂ Mark
ꔵ Move Page
Exit
6
MP3
Bit rate 32 kbps to 320 kbps
00:00 / 01:34
ꔂ Move
1
Progressive : 64 x 64 to 1024 x 768
6
No Marked
Title
JPEG
Available size
4
DriveA
1
Photo
Exit
3
MUSIC LIST
5
Supported file format
DAT, MPG, MPEG, VOB, AVI, DIVX, MP4, MKV, TS, TRP,
TP, ASF, WMV, FLV, RM, RMVB
Movie (*.mpg/*.mpeg/*dat/*.ts/*.trp/*.tp/*.
vob/*.mp4/*.mov/*.mkv/*.divx/*.avi/*.asf/*.
wmv/*.flv/*.avi(motion-jpeg)/*.mp4(motionjpeg)/*.mkv(motion-jpeg)/*.rm/*.rmvb)
supporting file
1
Moves to the upper level folder.
Video format : DivX 3.11, DivX 4, DivX 5, DivX 6,
Xvid1.00, Xvid1.01, Xvid1.02, Xvid1.03, Xvid1.10
beta-1/beta-2, Mpeg-1, Mpeg-2, Mpeg-4, H.264/
AVC, VC1, JPEG, Sorenson H.263
2
Preview: Displays the thumbnail/folder name of the file in
the selected folder.
Audio format : Dolby Digital, AAC, Mpeg, MP3,
LPCM, ADPCM, WMA
No.
3
4
5
6
Description
Current page/Total pages.
Total number of marked files.
Contents under the folder focused on 1.
Available buttons on the remote control.
Bit rate : within 32 kbps to 320 kbps (MP3)
External Subtitle format : *.smi/*.srt/*.su
b(MicroDVD,Subviewer1.0/2.0)/*.ass/*.ssa/*.
txt(TMPlayer)/*.psb(PowerDivX)
Internal Subtitle format : Only XSUB (It is the
subtitle format used in DivX6 files.)
16
Viewing photos
View image files saved in a USB storage device. The displays on the
screen may differ from the model.
ENGLISH
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
3 Press the Navigation buttons to scroll to PHOTO LIST and press
OK .
ꔊ
Slide show �
2/13
ꔡ
BGM
�
ꔋ
�
Option
Hide
4 Press the Navigation buttons to scroll to a folder/file you want and
press OK .
5 View photos by using the following menus buttons.
PHOTO LIST
DriveA
GUU.JPG
3872 x 2592, 2604 KB
Up Folder
ꔂ Move
Page 1/1
Option
No Marked
Up Folder
KY103
09/15/2016
KY101
04/03/2016
KY104
10/12/2016
KY102
09/03/2016
KY105
11/27/2016
GUU
11/27/2016
JMJ005
11/27/2016
JMJ002
11/27/2016
JMJ006
11/27/2016
JMJ003
11/27/2016
JMJ007
11/27/2016
11/27/2016
JMJ008
JMJ004
ꔉ PopUp Menu
Slideshow
BGM
11/27/2016
OK
FAV
Description
Scrolls through the files.
Mark All
Close
Hide
• The supported photo size is limited. You
cannot rotate a photo if the resolution of the
rotated width is larger than the supported
resolution size.
Hides the option window.
To display the options, press OK
.
Views the highlighted file or enters the mark
mode.
Moves to the previous or next page.
Q.MENU options for photo list
Enters the mark mode.
1 Press Q.MENU.
A pop-up window will appears.
Menu
View
Turns the background music on or off. To set the
background music folder, select Option.
Rotates photos clockwise (90°, 180°, 270°, 360°).
Exit
(Rotate)
Navigation
button
If there are no selected photos, all photos saved in
the current folder display during a slideshow.
To set a slideshow speed, select Option.
ꔵ Move Page
ꘂ Mark
Button
Description
Starts or stops a slideshow with selected photos.
Description
Views the selected photo.
Selects all files.
Exits the Mark Mode.
NOTE
• Non-supported files are displayed the preview image by icon only
.
• Abnormal files are displayed in the form of bitmap
.
6 The following options are available while viewing photos.
2 Press the Navigation buttons to scroll to Set photo view. and press
OK .
3 Press the Navigation buttons to scroll to one of the following options
and press OK .
Set photo view.
Option
Description
Slide Speed
Selects a slideshow speed (Fast, Normal,
Slow).
Music Folder
Selects a music folder for the background
music.
17
6 Control playback by using the following buttons.
Set video.
Allows you to change Video presets. (See p. 22)
Button
ENGLISH
Set audio.
Description
Stops playback.
Allows you to change Audio presets. (See p. 24)
Plays a music file.
Pauses or resumes playback.
Listening to music
Skips to the next file.
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
Skips to the previous file.
When playing,
or
3 Press the Navigation buttons to scroll to MUSIC LIST and press
OK .
When you press the
button, the previous
music file will be played.
4 Press the Navigation buttons to scroll to a folder/file you want and
press OK .
When you press the
button, the next
music file will be played.
5 Play music by using the following menus/buttons.
MUSIC LIST
Page 1/1
EXIT
No Marked
DriveA
Title
When you press the EXIT button, only the
music will be stopped and the player will go to
TV viewing.
When using the or
button during
playback a cursor indicating the position can
be played.
Duration
or
00:00 / 01:34
ꕗ
Q.MENU options for music list
Up Folder
ꔂ Move
ꘂ Mark
ꔉ PopUp Menu
Option
Button
Navigation
button
OK
ꔵ Move Page
Exit
Description
Scrolls through the files.
Views the highlighted file or enters the mark
mode.
Moves to the previous or next page.
FAV
Enters the mark mode.
Menu
Play
Play with Photo
Mark All
Close
1 Press Q.MENU.
A pop-up window will appears.
Set audio.
NOTE
Allows you to change Audio presets. (See p. 24)
• The TV will not play copy protected files.
• If the TV is not in use for some time during playback, the
information box as a screensaver will appear to prevent image
burn. To return to the Music list screen, press OK or BACK.
Description
Plays the selected music file.
File name
Musics
001.mp3
Displays photos during playback.
Selects all files.
Exits the Mark Mode.
ꕗ 00:53 / 05:31
Time elapsed / Duration
18
Viewing movies
Button
Description
Stops the playback.
2 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
Plays a video.
3 Press the Navigation buttons to scroll to MOVIE LIST and press
OK .
Pauses or resumes the playback.
Scans forward in a file.
4 Press the Navigation buttons to scroll to a folder/file you want and
press OK .
Scans backward in a file.
5 Play movie by using the following menus/buttons.
MOVIE LIST
Top Folder
DriveA
Page 1/1
Q.MENU
BACK
No Marked
Title
ENGLISH
1 Press SETTINGS to access the main menus.
EXIT
Duration
DriveA
or
4 folder(s), 2 file(s)
Shows the Option menu.
Hides the menu on the full-sized screen.
Returns to normal TV viewing.
Skips to specific points in a file during
playback. The time of a specific point will
appear on the status bar. In some files, this
function may not work properly.
Up Folder
ꔂ Move
ꔵ Move Page
ꔉ PopUp Menu
ꘂ Mark
Exit
Button
Navigation button
Description
Scrolls through the files.
Views the highlighted file or enters the
mark mode.
OK
Moves to the previous or next page.
FAV
Enters the mark mode.
Menu
Description
Plays the selected movie file.
Play
Once a movie file finishes playing, the next
selected one will be played automatically.
Mark All
Close
Marks all movie files on the screen.
Exits the Mark Mode.
6 Control playback by using the following buttons.
ꔋ
↓07:10
00:22:05
Tips for using playing video files
• • • • Some user-created subtitles may not work properly.
Some special characters are not supported in subtitles.
HTML tags are not supported in subtitles.
Subtitles in languages other than the supported languages are
not available.
• Changing font and colour in subtitles is not supported.
• Subtitles in languages other than one specified are not supported.
• Video files with subtitle files of 1 MB or larger may not be played
properly.
• The screen may suffer temporary interruptions (image stoppage,
faster playback, etc.) when the audio language is changed.
• A damaged movie file may not be played correctly, or some player
functions may not be usable.
• Movie files produced with some encoders may not be played
correctly.
• If the video and audio structure of recorded file is not interleaved,
either video or audio is outputted.
• HD videos with a maximum of 1920 x 1080 @ 25/30P or 1280 x 720
@ 50/60P are supported, depending on the frame.
• Videos with resolutions higher than 1920 X 1080 @ 25/30P or 1280
x 720 @ 50/60P may not work properly depending on the frame.
• Movie files other than the specified types and formats may not
work properly.
• Max bit rate of playable movie file is 20 Mbps. (only, Motion JPEG
: 10 Mbps)
• We do not guarantee smooth playback of profiles encoded level 4.1
or higher in H.264/AVC.
Option
19
ENGLISH
• DTS Audio codec is not supported.
• A movie file more than 30 GB in file size is not supported for
playback. The file size limit is dependent on the encoding
environment.
• A DivX movie file and its subtitle file must be located in the same
folder.
• A video file name and its subtitle file name must be identical for it
to be displayed.
• Playing a video via a USB connection that doesn’t support high
speed may not work properly.
• Files encoded with GMC (Global Motion Compensation) and Qpel
(Quarterpel Motion Estimation) may not be played.
• Trick Mode does not support other functions than if video files do
not have index information.
• Video file names that contain special characters may not be
playable.
1 Press Q. MENU to access the Pop-Up menus.
2 Press the Navigation buttons to scroll to Set video play., Set video.
or Set audio. and press OK .
When you select the Set video play.
1 Press the Navigation buttons to scroll to show the Picture Size,
Audio Language, Subtitle.
2 Press the Navigation buttons to scroll to make appropriate
adjustments.
Menu
Description
Picture Size
Selects your desired picture format during
movie play.
Audio Language
Changes the Language Group of the audio
during movie play. Files with a single audio
track cannot be selected.
Language
Turns on/off the subtitle.
Activated for SMI subtitle and can select the
language within the subtitle.
Selects the font for subtitle.
Code Page
Sync
Latin1
Cyrillic
Thai
Thai
.
Support Language
English, French, Spanish, Portuguese, Bahasa
Malaysia, Bahasa Indonesia
Russian
Hebrew
Hebrew
Arabic
Arabic, Persian, Kurdish
Vietnam
Vietnamese
• Only 10,000 of sync blocks can be supported within the subtitle
file.
• When playing a video, you can adjust the Picture Size by pressing
Q.MENU.
When you select the Set video.
1 Press the Navigation buttons to scroll to make appropriate
adjustments. (See p. 22)
Video options
Subtitle
Code Page
When set to default, same font as general
menu will be used.
Adjusts the time synchronisation of the
subtitle from -10 secs to +10 secs by steps of
0.5 secs during movie play.
When you select the Set audio.
1 Press the Navigation buttons to scroll to show the Sound Mode,
Auto Volume, Balance.
2 Press the Navigation buttons to scroll to make appropriate
adjustments. (See p. 24)
DivX® VOD Guide
DivX® VOD Registration
In order to play purchased or rented DivX® VOD contents, you should
register your device with 10 digit DivX registration code from your
device at www.divx.com/vod.
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
3 Press the Navigation buttons to scroll to DivX(R) VOD and press
OK .
4 Press the Navigation buttons to scroll to Registration and press
OK .
5 View the registration code of your TV.
You must register your device to
play DivX(R) protected videos.
Registration code : **********
Register at http://vod.divx.com
Close
.
20
6 When you are finished, press EXIT. When you return to the previous
menu, press BACK.
• • • • Menu
Description
SETUP
PICTURE
DivX® VOD Deregistration
You should deregister your device with 8 digit DivX deregistration code
from your device at www.divx.com/vod.
• Once the deregistration is executed, you must register your device
again to see DivX® VOD contents.
Adjusts the sound quality,
effect, or volume level.
TIME
Sets the time, date, or
timer feature.
OPTION
Customizes the general
settings.
LOCK
Locks or unlocks
programmes.
INPUT
Views the input sources
with their labels.
ENTERTAINMENT
Displays photo and play
music, movie, game
(Depending on model)
contents.
2 Press the Navigation buttons to scroll to ENTERTAINMENT and press
OK .
3 Press the Navigation buttons to scroll to DivX(R) VOD and press OK
.
4 Press the Navigation buttons to scroll to Deregistration and press
OK .
Deregistration code :
********
Deregister at http://vod.divx.com
Continue with registration?
Yes
No
6 When you are finished, press EXIT. When you return to the previous
menu, press BACK.
NOTE
• Once the deregistration is executed, you must register your device
again to see DivX(R) VOD contents.
Customizing settings
SETUP settings
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
BACK.
* Image shown may differ from your TV.
SETUP
Customizing TV setting
Adjusts the image size,
quality, or effect.
AUDIO
1 Press SETTINGS to access the main menus.
5 Press the Navigation buttons to select Yes to confirm.
Sets up and edit
programmes.
ENGLISH
Movie files are supported as follows
Resolution : Under 1920 x 1080 (W x H) pixels
Frame Rate : Under 30 frames/sec
Video Codec : MPEG 1, MPEG 2, MPEG 4, H.264/AVC, DivX 3.11,
DivX 4, DivX 5, DivX 6, Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.03,
Xvid 1.10-beta1, Xvid 1.10-beta2, JPEG, VC1, Sorenson H.263/H.264
Move
Move
OK
OK
Auto Tuning
Manual Tuning
Programme Edit
* Image shown may differ from your TV.
Accessing main menus
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to one of the following menus
and press OK .
3 Press Navigation buttons to scroll to the setting or option you want
and press OK .
4 When you are finished, press EXIT.
21
The available programme settings are described in the following:
Setting
The available picture settings are described in the following.
Description
Setting
ENGLISH
Auto Tuning
Tunes and stores all available
programmes through antennas inputs.
(See p. 12)
Manual Tuning
Tunes and stores the programmes you
want manually. (See p. 12)
Programme Edit
Edits programmes. (See p. 13)
PICTURE settings
Aspect Ratio
Reduces the power consumption by adjusting
the screen brightness.
Option
Energy Saving
1 Press SETTINGS and the Navigation buttons to scroll to PICTURE.
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
BACK.
Move
: 16:9
Aspect Ratio
ꕊ Energy Saving : Off
: Standard
Picture Mode
Move
•Backlight
100
•Contrast
100
•Brightness
50
•Sharpness
20
•Colour
55
•Tint
The Energy Saving is off.
Minimum/
Medium/
Maximum
Selects the brightness level.
Screen off
The screen turns off in 3 seconds.
Selects one of the preset image or customizes
options in each mode for the best TV screen
performance. You are also able to customize
advanced options of each mode.
OK
OK
Mode
0
R
G
• Colour Temperature C20
W
C
•Advanced Control
•Reset
Off
• When you select Screen Off, the screen
will be turned off in 3 seconds and Screen
Off will start.
• If you adjust “Energy Saving- Maximum”,
Backlight feature will not work.
* Image shown may differ from your TV.
PICTURE
Description
Changes the image size to view images at its
optimal size. (See p. 13)
Picture Mode
Vivid
Adjusts the video image for the
retail environment by enhancing
the contrast, brightness, colour,
and sharpness.
Standard
Adjusts the image for the normal
environment.
Cinema
Soccer /
Cricket
(Depending
on model)
Game
Optimizes the video images for
a cinematic look to enjoy movies
as if you are in a movie theatre.
Optimizes the video image for
high and dynamic actions by
emphasizing primary colours
such as white, grass, or sky blue.
Optimizes the video image for
a fast gaming screen such as
games.
If you turn this option on, colour temperature
will be automatically adjusted to reduce eye
strain.
Eye Comfort
Mode
22
Option
On
Automatically adjusts the screen
colour temperature.
Off
Turns off the Eye Comfort
Mode.
(Depending on model)
Setting
Setting
Description
Customizes the PC display options in RGB mode.
Resolution
Sets the desired resolution.
Options may only be selected
when the PC resolution is set to
1024 x 768 @ 60 /
1280 x 768 @60 /
1360 x 768 @ 60 /
1366 x 768 @ 60 (default).
Auto
config.
Sets to adjust the screen
position, clock, and phase
automatically. The displayed
image may be unstable for
a few seconds while the
configuration is in progress.
Position/
Size/Phase
Adjusts the options when the
picture is not clear, especially
when characters are shaky,
after the auto configuration.
Screen
(RGB-PC)
Reset
Setting
Description
Backlight
Adjusts the brightness of the screen
by controlling the LCD backlight. If
you decrease the brightness level, the
screen becomes darker and the power
consumption will be reduced without
any video signal loss.
Contrast
Increases or decreases the gradient
of the video signal. You may use
Contrast when the bright part of the
picture is saturated.
Brightness
Adjusts the base level of the signal in
the picture.
Sharpness
Adjusts the level of crispness in the
edges between the light and dark
areas of the picture. The lower the
level, the softer the image.
Adjusts the balance between red and
green levels.
Tint
Adjusts the overall tone of the screen
as desired.
Colour Temperature
Advanced Control
Reset
Set to warm to enhance hotter colours
such as red, or set to cool to see less
intense colours with more blue.
Customizes the advanced options.
Restores the options of each mode to
the factory default.
Advanced image options (Depending on model)
Setting
Description
Dynamic Contrast
Adjusts the contrast to keep it at the best
level according to the brightness of the
screen. The picture is improved by making
bright parts brighter and dark parts darker.
Restores the options to the
default setting.
Basic image options
Adjusts intensity of all colours.
ENGLISH
Option
Description
Colour
Dynamic Colour
Adjusts screen colours so that they look
livelier, richer and clearer. This feature
enhances hue, saturation and luminance
so that red, blue and green white look
more vivid.
Noise Reduction
Reduces screen noise without compromising
video quality.
You can adjust brightness of dark area and
middle gray level area of the picture.
Gamma
Black Level
Motion Eye Care
Film Mode
• Low: Make the dark and middle gray
level areas brighter.
• Medium: Express the original picture
level.
• High: Make the dark and middle gray
level area darker.
Sets black level of the screen to proper level.
This function is available in the following
modes: RF, AV or HDMI.
• Low: The reflection of the screen gets
darker.
• High: The reflection of the screen gets
brighter.
Adjusts screen brightness to prevent eye
glare.
Makes video clips recorded in film look more
natural.
This feature operates only in 480i / 576i /
1080i Resolution.
23
Setting
Description
Setting
Advanced control
Maximizes the utilization of colour to
increase colour quality.
• Standard: Displays standard set of
colours.
• Wide: Increase number of colours used.
ENGLISH
Colour Gamut
Mode
Shows clearer and distinctive yet natural
edges of the video.
Edge Enhancer
• Depending on input signal or other picture settings, the range of
detailed items for adjustment may differ.
1 Press SETTINGS and the Navigation buttons to scroll to AUDIO.
3 When you return to the previous menu, press
Standard
Select when you want
standard-quality sound.
Music/
Bollywood
(Depending
on model)
Select when you listen to
music.(Bollywood is india
special music mode)
Sound Mode
Soccer / Cricket
(Depending on
model)
Select when you play games.
Treble
Controls the dominant
sounds in the output. When
you turn up the treble, it will
increase the output to the
higher frequency range.
Bass
Controls the softer sounds in
the output. When you turn
up the bass, it will increase
the output to the lower
frequency range.
Reset
Resets the sound mode to
the default setting.
Option
BACK.
Move
Auto Volume
Balance
Sound Mode
TV Speaker
Move
: On
0
: Standard
•Treble
•Bass
•Reset
L
OK
OK
R
50
50
: On
The available audio settings are described in the following.
Setting
TV Speaker
Turns off the internal speaker of the TV when
using an external Hi-Fi system.
Description
Auto Volume
Activates the Auto Volume feature to keep the
volume level consistent whenever you change
programmes. The volume level may not be
consistent due to different signal conditions of
broadcasting stations.
Balance
Adjust balance between the left and right
speakers according to your room environment.
Stereo/Dual Reception
This feature may not be applied based on country broadcasting
circumstance.
When a programme is selected, the sound information for the station
appears with the programme number and station name.
Press I/II button to select the Multi Audio menu.
Broadcast
On Screen Display
Mono
MONO
Stereo
STEREO
Dual
NICAM
24
Select when you watch
sports events.
Game
* Image shown may differ from your TV.
AUDIO
Select when you watch
movies.
Cinema
AUDIO settings
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
Description
Selects one of the preset sound modes or
customizes options in each mode.
DUAL I , DUAL II , DUAL I + II
NICAM
yyMono sound selection
If the stereo signal is weak in stereo reception, you can switch to
mono. In mono reception, the clarity of sound is improved.
DUAL I
DUAL I I
DUAL I+I I
Sends the primary broadcast language to the
loudspeakers.
Sends the secondary broadcast language to the
loudspeakers.
Sends a separate language to each loudspeaker.
1 Press SETTINGS and the Navigation buttons to scroll to TIME.
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
Sound output can be selected according to the type of broadcast
received.
BACK
* Image shown may differ from your TV.
TIME
Move
Move
Clock
Off Time
On Time
Sleep Timer
Automatic Standby
Auto Off(On Time)
Nicam Reception
If the TV is equipped with a receiver for NICAM reception, high quality
NICAM (Near Instantaneous Companding Audio Multiplex) digital sound
can be received.
OK
OK
: Off
: Off
: Off
: 4 hours
: Off
The available time settings are described in the following.
Setting
Clock
Description
Sets the time.
Off Time /
On Time
Sets the time to turn on or off the TV
automatically. To use this function, you should
set the current time and date in advance.
• If you do not press any button within 2
hours after the TV turns on by the On Time
feature, the TV enters the Standby mode
automatically.
• If you set both Off Time and On Time
features to the same time, the Off Time
feature overrides the On Time feature.
In AV, Component, HDMI mode, you can select output sound for the left
and right loudspeakers.
Sleep Timer
Sets the length of time until the TV to turns off.
When you turn the TV off and turn it on again,
the Sleep Timer feature will be set to off.
Select the sound output.
Automatic
Standby
1 When NICAM mono is received, you can select NICAM MONO or
FM MONO.
2 When NICAM stereo is received, you can select NICAM STEREO or
FM MONO.
If the stereo signal is weak, switch to FM MONO.
3 When NICAM dual is received, you can select NICAM DUAL I, NICAM
DUAL II or NICAM DUAL I+II or FM MONO.
Speaker Sound Output Selection (Depending on model)
L+R:
Audio signal from audio L input is sent to the left
loudspeaker and audio signal from audio R input is sent
to the right loudspeaker.
(Depending on
model)
L+L:
Audio signal from audio L input is sent to left and right
loudspeakers.
Audio signal from audio R input is sent to left and right
loudspeakers.
Auto Off(On
Time)
(Depending on
model)
R+R:
ENGLISH
yyLanguage selection for dual language broadcast
If a programme can be received in two languages (dual language),
you can switch to DUAL I, DUAL II or DUAL I+II.
TIME settings
If you do not press any button on the TV or
remote control for a certain period, the TV will
automatically switch to standby mode.
If On Time is enabled, the TV will be turned
on at the specified time. If you do not operate
the TV for two hours, the TV will be turned off
automatically.
25
ENGLISH
OPTION settings
LOCK settings
1 Press SETTINGS and the Navigation buttons to scroll to OPTION.
1 Press SETTINGS and the Navigation buttons to scroll to LOCK.
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
BACK.
3 When you return to the previous menu, press
* Image shown may differ from your TV.
OPTION
OK
OK
: Off
: Off
Description
Selects a desired language.
Input Label
Indicates which device is connected to which
input port.
USB AutoRun
When your TV is turned on with a USB device
connected or when you connect a USB device
to your TV, the photos or videos will be played
automatically.
Mosquito Away makes a sound only
mosquitos can hear to make them go away.
Connect the Mosquito Away speaker to
your TV to enable this feature. You must use
the Mosquito Away speaker to enable this
feature.
• Make sure the Mosquito Away jack is
connected securely to the port on the TV.
Factory Reset
26
Move
Move
OK
OK
: Off
: Home Use
Setting
Mosquito Away
LOCK
Lock System
Set Password
Block Programme
Input Block
The available option settings are described in the following.
Menu Language
BACK.
* Image shown may differ from your TV.
Move
Move
Menu Language
Input Label
USB AutoRun
Mosquito Away
Factory Reset
3 When you return to the previous menu, press
Customizes the TV settings to suit your
preference. The initial setup screen will
appear when you turn on the TV for the
first time.
Home Use
Selects it for the Home
environment.
Store Demo
Selects it for the retail
environment.
The available lock settings are described in the following.
Setting
Description
Lock System
Activates or deactivates the lock system.
Set Password
Changes the 4-digit password. The
default PIN is “0 0 0 0”.
Block Programme
Input Block
Blocks the programmes that contain
inappropriate contents for children
by pressing the Blue button. The Lock
icon appears in front of the blocked
programmes. The programmes can be
selected but the screen blank and the
audio is muted.
Blocks the input sources.
Teletext
ENTERTAINMENT settings
1 Press SETTINGS and the Navigation buttons to scroll to
ENTERTAINMENT.
3 When you return to the previous menu, press
BACK.
* Image shown may differ from your TV.
ENTERTAINMENT
Move
Move
OK
OK
Photo List
Music List
* This feature is not available in all countries.
Teletext is a free service broadcast by most TV stations which gives upto-the minute information on news, weather, television programmes,
share prices and many other topics.
ENGLISH
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
The teletext decoder of this TV can support the SIMPLE and FASTEXT
systems. SIMPLE (standard teletext) consists of a number of pages
which are selected by directly entering the corresponding page
number. FASTEXT are more modern methods allowing quick and easy
selection of teletext information.
Movie List
DivX(R) VOD
Switch On/Off
Game
Press the
button to switch to teletext. The initial page or last
page viewed appears on the screen.
The available entertainment settings are described in the following.
Two page numbers, TV station name, date and time are displayed on
the screen headline. The first page number indicates your selection,
while the second shows the current page displayed.
Press the
reappears.
button to switch off teletext. The previous mode
Setting
Description
Photo List
Views image files(photos) on TV which
are stored on USB device. (See p. 17)
Music List
Plays back music files on TV which are
stored on USB device. (See p. 18)
Simple text
Movie List
Plays movie files on TV which are
stored on usb device. (See p. 19)
Page selection
DivX(R) VOD
Views the registration code of your TV.
(See p. 20)
Game
(Depending on model)
Plays game contents on your TV.
1 Enter the desired page number as a three digit number with the
Number buttons. If during selection you press a wrong number, you
must complete the three digit number and then re-enter the correct
page number.
2 The
button can be used to select the preceding or
following page.
Fastext
The teletext pages are colour coded along the bottom of the screen and
are selected by pressing the corresponding coloured button.
Page selection
1 Press the INDEX button to select the index page.
2 You can select the pages which are colour coded along the bottom
line with corresponding coloured buttons.
3 AS with SIMPLE teletext mode, you can select a page by entering its
three digit page number with the Number buttons in FASTEXT mode.
4 The
button can be used to select the preceding or
following page.
27
Special teletext function
Index
ENGLISH
Select the each index page.
Time
When viewing a TV programme, select this menu to display the time at
the top right hand corner of the screen.
In the teletext mode, press this button to select a sub page number. The
sub page number is displayed at the bottom of the screen. To hold or
change the sub page, press the Red/Green,
or Number buttons.
Hold
Stops the automatic page change which will occur if a teletext page
consists of 2 or more sub pages.
The number of sub pages and the sub page displayed is, usually, shown
on the screen below the time. When this menu is selected the stop
symbol is displayed at the top left-hand corner of the screen and the
automatic page change is inactive.
Reveal
Select this menu to display concealed information, such as solutions to
riddles or puzzles.
Update
Displays the TV picture on the screen while waiting for a new teletext
page. The display will appear at the top left hand corner of the screen.
When the updated page is available then display will change to the
page number. Select this menu again to view the updated teletext
page.
Preventing “Image burn” or “Burn-in” on
your TV screen
• If a fixed image displays on the TV screen for a long period of time,
it will be imprinted and become a permanent disfigurement on
the screen. This is “image burn” or “burn-in” and not covered by
the warranty.
• If the aspect ratio of the TV is set to 4:3 for a long period of time,
image burn may occur on the letterboxed area of the screen.
• Avoid displaying a fixed image on the TV screen for a long period
of time (2 or more hours for LCD) to prevent image burn.
Troubleshooting
General
Cannot control the TV with the remote control.
• Check the remote control sensor on the product and try again.
• Check if there is any obstacle between the product and the remote
control.
• Check if the batteries are still working and properly installed (
to , to ).
No image display and no sound is produced.
• Check if the product is turned on.
• Check if the power cord is connected to a wall outlet.
• Check if there is a problem in the wall outlet by connecting other
products.
The TV turns off suddenly.
• Check the power control settings. The power supply may be
interrupted.
• Check if the Automatic Standby (Depending on model) / Sleep
Timer / Off Time is activated in the TIME settings.
• If there is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
• If On Time is enabled, the TV will be turned on at the specified
time. If you do not operate the TV for two hours, the TV will be
turned off automatically. To disable this function, use your remote
control to go to SETTINGS TIME Auto Off(On Time)
(Depending on model) Off.
When connecting to the PC (HDMI/RGB), ‘No signal’ or ‘Invalid
Format’ is displayed.
• Turn the TV off/on using the remote control.
• Reconnect the HDMI/RGB cable.
• Restart the PC with the TV on.
28
Abnormal Display
Generated Sound
• “Cracking” noise: A cracking noise that occurs when watching or
turning off the TV is generated by plastic thermal contraction due
to temperature and humidity. This noise is common for products
where thermal deformation is required.
• Electrical circuit humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit, which supplies a
large amount of current to operate a product. It varies depending
on the product.
This generated sound does not affect the performance and
reliability of the product.
Specifications
Environment
condition
Operating
Temperature
0 °C to 40 °C
Operating
Humidity
Less than 80 %
Storage
Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
ENGLISH
• If the product feels cold to the touch, there may be a small “flicker”
when it is turned on. This is normal, there is nothing wrong with
product.
• This panel is an advanced product that contains millions of pixels.
You may see tiny black dots and/or brightly coloured dots (red, blue
or green) at a size of 1 ppm on the panel. This does not indicate a
malfunction and does not affect the performance and reliability
of the product.
This phenomenon also occurs in third-party products and is not
subject to exchange or refund.
• You may find different brightness and color of the panel depending
on your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel.
It is not related with the product performance, and it is not
malfunction.
• Displaying a still image for a prolonged period of time may cause
image sticking. Avoid displaying a fixed image on the TV screen for
a long period of time.
Analogue TV
(Depending on Country)
Television system
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
Programme coverage
VHF, UHF, CATV
Maximum number of
storable programmes
200
External antenna
impedance
75 Ω
• The energy information provided with the product is indicated in
accordance with the regulations of each country. (Depending on
country)
- The Energy consumption is measured in accordance with IEC
62087.
• Actual Energy consumption may vary depending on factors such as
the type of video content being played and TV settings.
HDMI-DTV supported mode
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
720 x 480
31.469
31.5
59.94
60.00
720 x 576
31.25
50.00
1280 x 720
44.96
45
37.5
59.94
60.00
50.00
1920 x 1080
28.125
33.72
33.75
56.25
67.432
67.5
27
33.75
26.97
33.716
50.00
59.94
60.00
50.00
59.94
60.00
24.00
30.00
23.97
29.976
29
Regulatory
RGB-PC supported mode
ENGLISH
Resolution
Horizontal
Frequency
(kHz)
640 x 480
31.469
59.94
800 x 600
37.879
60.317
1024 x 768
48.363
60.0
1280 x 720
47.77
59.85
1152 x 864
54.34
60.05
1366 x 768
47.71
59.79
• The optimal display resolution
- 1366 x 768 @ 60 Hz.
Vertical
Frequency
(Hz)
• The optimal timing in each mode is vertical frequency 60 Hz.
AC/DC Adapter
24LJ47**
Manufacturer : Honor
Model : ADS-45EI-19 19032GPI
WARNING!
Never place a television set in an unstable location. A television set may
fall, causing serious personal injury or death. Many injuries, particularly
to children, can be avoided by taking simple precautions such as:
• Using cabinets or stands recommended by the manufacturer of the
television set.
• Only using furniture that can safely support the television set.
• Ensuring the television set is not overhanging the edge of the
supporting furniture.
• Not placing the television set on tall furniture (for example,
cupboards or bookcases) without anchoring both the furniture and
the television set to a suitable support.
• Not placing the television set on cloth or other materials that may
be located between the television set and supporting furniture.
• Educating children about the dangers of climbing on furniture to
reach the television set or its controls.
If your existing television set is being retained and relocated, the same
considerations as above should be applied.
Symbols
Refers to alternating current(AC).
Manufacturer : APD
Model : WA-32C19FI
Refers to direct current(DC).
Input: AC 100-240 V~ 50/60 Hz
Output: 19 V 1.7 A
Refers to class II equipment.
Refers to stand-by.
Refer to “ON” (power).
Refers to dangerous voltage.
30
Disclaimer
ENGLISH
IMPORTANT: Long term effect not tested and mosquitoes may become resistant. Mosquito species used in the test below may differ from the
mosquito species of your region. This product is one of the ways to manage mosquitoes and not intended to replace other protective devices against
mosquitoes. Some low-level noise may be heard from the TV when the Mosquito Away feature is activated. It is normal and there is no need to be
concerned.
Test Details:
Tested by International Institute of Biotechnology and Toxicology (IIBAT), India, According to LG internal testing method.
• Test conducted, three times at temperature of 27±2°C and humidity of 60±10%.
• Test used two chambers size 3.5 m x 2.6 m x 2.2 m, the chamber with the LG Mosquito Away TV assumed to be inside (“inside
chamber”) and the chamber without the LG Mosquito Away TV assumed to be outside (“outside chamber”).
• Cages (25 cm3) are placed inside each chamber, connected using netted sleeves to enable the movement of the mosquitoes from
one cage to another.
• One person is placed inside the chamber to attract mosquitoes.
• For each test, 50 lab cultured 3-5 days old mosquitoes were placed in the cage in outside chamber; number of mosquitoes coming
into the cage in inside chamber was counted every 10 minutes for 90 minutes under 2 settings:
- Control setting (Mosquito repelling ultrasonic OFF)
- Treatment setting (Mosquito repelling ultrasonic ON)
Test Result:
Found to repel on average 76.7% of Aedes aegypti mosquitoes. Repel rate shows percentage of mosquitoes prevented from entering the
inside chamber after 90 minutes of Treatment setting compared to Control setting. Represented average of 76.7% derived from 71.2%,
77.9%, 81.0%.
Results may vary in other settings, including but not limited to temperature, humidity, location, space, mosquito species, number of
mosquitoes, number of persons, and operation time.
31
Record the model number and serial number
of the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
MODEL
SERIAL
Download PDF