LG | 29FU6RS | LG 29FU6RS Owner’s Manual

OWNER’S MANUAL
Colour Television
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number :
Serial number :
P/NO : MFL65001803-EN (CW91D)(1009-REV00)
www.lg.com
Installation
Power
Service
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover.
Never apply DC power to the set. In the event of
thunderstorms or powercuts, please pull out the
aerial and power plug.
Never remove the back cover of the set as this can
expose you to very high voltage and other hazards. If
the set does not operate properly, unplug it and call
your dealer.
Press the POWER button on the front panel or side
panel to turn off the TV when the TV set is not being
used for a long time.It is recommended to remove the
plug from the wall outlet(Power point).
Disconnecting device from mains
Mains plug is the disconnecting device. The plug
must remain readily operable
Warning
To prevent fire or shock hazard, do not expose the set
to rain or moisture.
Do not place anything containing liquid on top of the set,
this may cause a fire or could give an electric shock.
Aerial
Connect the aerial cable to the socket on the back
cover. For the best reception an outdoor aerial
should be used.
Location
Position your set so that no bright light or sunlight
falls directly onto the screen. Care should be
taken not to expose the set to any unnecessary
vibration, moisture, dust or heat. Also ensure that
the set is placed in a position to allow a free flow
of air. Do not cover the ventilation openings on the
back cover.
Connection of external equipment
Aerial socket
Euro scart socket (option)
1. Connect the RF out socket of the VCR to the
aerial socket on the back of the set.
2. Connect the aerial cable to the RF aerial in
socket of the VCR.
3. Store the VCR channel on a desired programme number using the ‘Auto programme
tuning’ section.
4. Select the programme number where the
VCR channel is stored.
5. Press the PLAY button on the VCR.
1. Connect the Euro scart socket of the VCR to
the Euro scart socket of the set.
2. Press the PLAY button on the VCR.
If your VCR outputs a switching voltage when
connected to Euro scart socket, the set will
switch to AV 1 mode automatically. But if you
want to keep on watching TV mode, press the
D / E or NUMBER buttons.Otherwise press
the TV/AV button on the remote control
handset to select AV 1 The VCR playback picture appears on the screen.
You can also record programmes received by the
TV on video tape.
Note : Signal type RGB, i.e. the signals red, green
and blue can only be selected for the Euro scart
socket. These signals are transmitted, for example, by a pay TV decoder, game machine or photo
CD unit, etc.
Audio/Video in/out sockets (option)
1. Connect the audio/video out sockets of the VCR
to audio/video in sockets of the set and in sockets of the VCR to RF OUT sockets of the set.
2. If the VCR is connected to the AV sockets on the
set, press the TV/AV button to select AV1 or
AV2(option).
3. Press the PLAY button on the VCR.The VCR
playback picture appears on the screen.
You can also record programmes received by the
TV on video tape via audio/video out sockets.
Note :
If you have a mono VCR, connect the audio cable
from the VCR to the AUDIO L/MONO socket of
the set.
And if connected to AV2(option),then you should
select L+L mode by pressing the I/II/*(option) key.
2
Component in sockets (option)
1. Connect the COMPONENT video output
sockets (Y Cb Cr, Y Pb Pr or Y B-Y R-Y) of the
COMPONENT (480i) to the COMPONENT
INPUT sockets (Y PB PR) on the set.
2. Connect the audio cable from the COMPONENT to AUDIO IN sockets of AV IN1.
3. Press the TV/AV button to select COMPONENT.
4. Press the PLAY button on the COMPONENT.
The COMPONENT playback picture appears
on the screen.
Location and function of controls
Remote control handset
Before you use the remote control handset,
please install the batteries.
1
2
Q.VIEW
LIST/
9
10
11
Returns to the previously viewed programme.
11. LIST/ (option)
*
Displays the programme table.
12. FAVOURITE/ (option)
Selects a favorite programme.
13. I/II/ (option)
*
*
Selects the language during dual language broacast.
Selects the sound output (option).
14. EYE/ (option)
*
Switches the eye function on or off.
: No function
*COLOURED
BUTTONS :
3
12
4
These buttons are used for teletext (only TELETEXT models) or programme edit.
FAVOURITE/
Battery installation
5
6
7
13
8
The remote control handset is powered by AAA
type batteries. Install batteries as indicated by the
polarity symbols ( + and - ) marked inside the
compartment.
Note :
To avoid damage from possible battery leakage,
remove the batteries if you do not plan to use the
remote control handset for an extended period of
time.
14
1. POWER
Switches the set on from standby or off to standby.
2. MUTE
Switches the sound on or off.
3. NUMBER BUTTONS
Switches the set on from standby or directly select a number.
USB SELECT BUTTONS
Oprate USB function.
4. MENU
To display on-screen or exit from USB mode .
Other local key is not available in USB mode.
5. D / E (Programme Up/Down)
Selects a programme or a menu item.
Switches the set on from standby.
F / G (Volume Up/Down)
Adjusts the volume.
Adjusts menu settings.
OK
Accepts your selection or displays the current mode.
6. TELETEXT BUTTONS (option)
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
7. SLEEP
Sets the sleep timer.
8. USB BUTTON
Select the USB mode.
9. TV/AV
Selects TV or AV mode.
Switches the set on from standby.
Exits the Teletext mode.
10. Q.VIEW (or YELLOW)
or
Front panel
MAIN POWER (ON/OFF)
Switches the set on or off.
POWER/STANDBY INDICATOR
Illuminates brightly when the set is in standby
mode.dims when the set is switched on.
REMOTE CONTROL SENSOR
Note : Only use the supplied remote control
handset. (When you use others, they will not
be able to function.)
MENU
Selects a menu.
OK
Accepts your selection or displays the current
mode.
F / G (Volume Down/Up)
Adjusts the volume.
Adjusts menu settings.
D / E (Programme Up/Down)
Selects a programme or a menu item.
Switches the set on from standby.
AUDIO/VIDEO/USB IN SOCKETS (AV
IN2)(option)
Connect the audio/video/USB out sockets of
external equipment to these sockets.
Note :
What is shown here may be somewhat different
from your set or can not be supplied on your
area.
3
Basic operation
On and off
1. Press the main power button to switch the set on.
2. If the set is in standby mode, press the
POWER, D / E, TV/AV or NUMBER buttons on
the remote control handset to switch it on fully.
3. Press the POWER button on the remote control handset.
The set reverts to standby mode.
4. Press the main power button again to switch
the set off.
Note : If, while the set is switched on, the mains
plug is disconnected the set will switch to standby
or power on when the mains plug is replaced in
the mains power socket.
Mute function
and the display W appears.
You can cancel it by pressing the MUTE, F / G,
I/II/ (option), button.
*
On screen language selection(option)
The menu can be displayed on the screen in
desired language. First select your language.
1. Press the MENU button and then D / E button to select the Special menu.
2. Press the Gor OK button to select Language.
3. Press the F / G button to select your desired
language.
All the on screen displays will appear in the
selected language.Press the MENU button to
return to the Special menu.
4. Repeatedly press the MENU button to return
to normal TV viewing.
Press the MUTE button. The sound is switched off
Other functions
TV and AV modes
AV mode is used when a video cassette recorder
(VCR), or other equipment is connected to the set.
Note : When a VCR is connected via the aerial
socket the set is used in TV mode. See the
‘Connection of external equipment’ section.
AV1 : VCR connected to the Euro scart socket or
AV IN 1 sockets on the set
AV2 : VCR connected to the AV IN 2 sockets on
the set (option).
COMPONENT : DVD Player connected to the
COMPONENT sockets on the set (option).
Alternatively you can select the TV or AV mode by
pressing the TV/AV button.
In AV mode, to return to TV mode, press the D /
E or NUMBER buttons.
Auto AV switching (option)
If your VCR outputs switching voltage when it is
switched to playback with the VCR connected to the
Euro scart socket. The set is automatically switched
to AV1 mode when an AV signal is input. But if you
want to keep on watching TV mode, press the D / E
or NUMBER buttons. Press the TV/AV button to
return to AV modes.
Child lock
The TV can be set so that the remote control handset is needed to control it. This feature can be used
to prevent unauthorized viewing.
With the lock on, the display Child lock on
appears on the screen if any button on the front
panel is pressed while viewing the TV.
Degaussing (option)
Due to the super large Tube in the set. The colour
purity of the picture may be affected by other
4
magnetic influences such as speakers. Stripes
may appear on the screen or there may be colour
patches.
Note : If you cannot adjust the screen condition by
degaussing, try it again after about 4 minutes.
Sleep timer
You don’t have to remember to switch the set off
before you go to sleep. The sleep timer automatically switches the set to standby after the preset
time elapses.
Repeatedly press the SLEEP button to select the
number of minutes. The display
- - - will appear
on the screen, followed by 10, 20, 30, 60, 90, 120,
180 and 240. The timer begins to count down from
the number of minutes selected.
Note :
a. To view the remaining sleep time, press the
SLEEP button once.
b. To cancel the sleep time, repeatedly press the
SLEEP button until the display - - - appears.
c. When you switch the set off, the set releases
the preset sleep time.
Energy Saving (option)
If On is selected for Energy Saving,the TV
screen will be turned off and the energy saving
mode will be started within 10 seconds.The energy saving mode saves energy by about 70% compared with the normal status.And only sound is
output,no picture is displayed.
After the energy saving mode is started,you can
adjust volume levels by pressingF / G button
(while the volume bar OSD is not displayed.)
Press any key(except F / G button)to exit from this
fuction.
On screen menus
The dialogue between you and your set takes
place on screen with an operator menu. The buttons required for the operating steps are also displayed.
Menu selection
Setting up TV stations
Auto programme tuning
All stations that can be received are stored by this
method. It is recommended that you use auto programme during installation of this set.
Auto programme
1. Press the MENU button and then D / E button to display each menu.
2. Press the G or OK button and then D / E button to select a menu item.
3. Change the setting of an item with the
F / G button.
You can move to the higher level menu with
the MENU button and to move to the lower
level menu press the G or OK button.
Note :
a. In the teletext mode, menus are not displayed.
b. In some models, Degauss will not display.
c. In some models, the Language will not display.
d. In some models, the Treble, Bass will not
display,but there will be Equalizer setting.
Station
AutoOprogramme
Programme
Skip
Delete
Swap
SoundOsystem
ColourOsystem
Fine
:OOToOstart
:OO1
:OOOff
:OOOff
:OO
:OOBG
:OOAuto
:OO{{{
()O}{OOKOMENU
Station menu
Picture
PSM
XD
CSM
Contrast
Brightness
Colour
Sharpness
Tint
:OODynamic
:OOOff
:OOStandard
:OO100
:OO60
:OO60
:OO60
:OO0
OOCO01O(BG)
7
36%
MENU
Programme
This function enables you to select the programme
number in setting mode.
Skipping a programme number
1. In station mode ,select skip item.
2. Press the F / G button to select ON or OFF.
When a programme number is skipped it
means that you will be unable to select it
using the D / E button during normal TV
viewing. If you want to select the skipped
programme, directly enter the programme
number with the NUMBER buttons.
Repeatedly press the MENU button to return to
normal TV viewing.
Deleting a programme
1. In station mode ,select delete item.
2. Press the F / G button to select ON or OFF.
Press the OK button when ON is selected ,then
the selected programme is deleted, and all the
following programmes are shifted up one position.
()O}{OOKOMENU
Picture menu
Sound
SSM
TurbooSound
AVL
Balance
Treble
Bass
:OOFlat
:OOOff
:OOOff
:OO0
:OO50
:OO50
Sound menu
Clock
Offotime
Onotime
Onotimeovolume
Autoosleep
1. In station mode ,select swap item.
2. Press the F / G button to select the programme
number.Press the OK button to swap the current
programme for the selected programme.
Sound system
()O}{OOKOMENU
Time
Swapping a programme number
:OO-i-o:o-i:OO-i-o:o-i:OO-i-o:o-i:OO30
:OOOff
System :
BG :(Asia/NewZealand/ M.East/Africa/Australia)
I
:(Hong Kong/South Africa)
DK :(East Europe/China/Africa/CIS)
M : (USA/Korea/Philippines) (option)
Colour system
()O}{OOKOMENU
Time menu
Special
Language
Input
Childolock
Degauss
Energyosaving
:OOEnglish
:OOTV
:OOOff
:OOOff
:OOOff
()O}{OOKOMENU
Special menu
TV programme
You can adjust colour systerm in AUTO,PAL,
PAL60,NTSC(option),NTSC4.43(option) and
SECAM.
Fine tuning
Normally fine tuning is only necessary if reception
is poor.The finely tuned programme will be indi
cated by yellow number during programme selection.
5
Picture adjustment
Note: Picture menu options are not available for
the RGB input source.
PSM (Picture Status Memory)
The picture Dynamic, Standard, Mild and
Game are programmed for good picture reproduction at the factory and cannot be changed.
XD
You can enjoy the vivid and hi-definition picture with
LG’s excellent Digital Reality processor technology.
CSM (Colour Status Memory)
You can select the picture colour status;
Standard, Reddish, Greenish or Bluish as
you prefer.
Picture adjustment
You can adjust picture Contrast ,Brightness ,
Colour ,Sharpness and Tint (NTSC input
only) to the levels you prefer.
Time Setting
Setting the On/Off timer
By using this function, the set automatically switches on or off at a preset time. You must set the time
correctly before using the on/off time function.
Note :a.On time works only in standby mode.
b.To view the remaining on/off time, select
the Time menu.
c.When you switch the main power off, the
Clock is reset .
On time volume
In this function,you can set the volume of the TV
automatically turnning on.
Auto sleep
If you select On on the Auto sleep item,
the set will automatically switch itself to
standby mode approximately ten minutes after a
TV station stops broadcasting.
Sound adjustment
SSM (Sound Status Memory)
The sound Flat, Music, Movie , Sport are programmed for good sound reproduction at the factory and cannot be changed.
Turbo sound selection
When this function is on, the sound will be more
emphasized and amplified than normal sound.
Sound adjustment
You can adjust Balance, AVL (Auto Volume
Leveler), Treble ,Bass. AVL automatically keeps
on an equal volume level even if you change programmes. The Turbo sound creates an all around
sound as in a concert hall.
Sound output selection
In AV mode, you can select output sound for the
left and right loudspeakers.
Repeatedly press the I/II/ button to select the
sound output.
L+R :Audio signal from audio L input is sent to left
loud-speaker and audio signal from audio R
input is sent to right loud-speaker.
*
L+L or R+R (option): Audio signal from audio L or R
input is sent to both left and right loud-speakers.
Note:
L+L or R+R may be inavailable for some models.
Stereo/Dual reception (option)
When a programme is selected, the sound information for the station appears after the programme number and station name disappear.
Broadcast
Mono
Stereo
Dual
6
On Screen Display
MONO
STEREO
DUAL I
Mono sound selection
In stereo reception if the stereo signal is weak,
you can switch to mono by pressing the I/II/ button twice. In mono reception the depth of sound is
improved. To switch back to stereo, press the
I/II/ button twice again.
Language selection for dual language broadcast
If a programme is received in two languages (dual
language), you can switch to DUAL I, DUAL II or
DUAL I+II by pressing the I/II/ button repeatedly.
DUAL I sends the primary broadcast language to
the loudspeakers.
DUAL II sends the secondary broadcast language to the loudspeakers.
DUAL I+II sends a separate language to each
loudspeaker.
*
*
*
NICAM reception (option)
If your set is equipped with the receiver for NICAM
reception, the high quality NICAM (Near
Instantaneous Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the
type of received broadcast by pressing the I/II/
button repeatedly.
1. When NICAM mono is received, you can
select NICAM MONO or FM MONO.
2. When NICAM stereo is received, you can
select NICAM STEREO or FM MONO. If the
stereo signal is weak, switch to FM mono.
3. When NICAM dual is received, you can select
NICAM DUAL I, NICAM DUAL II or
NICAM DUAL I+II or MONO. When FM
mono is selected the display MONO appears
on the screen.
*
USB MODE(option)
USB connection
Connect the USB port of USB memory to the
USB port on the side of the TV.
After connecting the USB IN jacks, press the
USB button.
USB
Removing the USB device from TV
1. Press STOP(A/ESC) twice to return to the
USB menu .
2. Remove the USB device from TV.
- When you plug a USB then press the USB button, the below screens will be displayed.
- Enter into USB mode
USB
1.Press “USB”key on remote control.
2.Slecte“USB” on the main menu
special mode
- Exit from the “USB”mode
1.Press “USB”or “MENU”in USB mode .
2.Press local key “MENU”in USB mode.
Special
Language
Input
Childolock
Degauss
USB
{
{
{
{
{ ON
()O}{OOKOMENU
Notes :
1. Don’t extract the USB device while
operating.Music files (MP3), image files (JPG),
AVI files and Game files(SMF) can be played.
2. This unit can not use a USB HUB.
3. Recommended USB device and file system.
- Connecting USB device should comply with
USB 2.0 specifications.
- Compatible with : FAT16, FAT32
(Recommend FAT32 for USB over 2GB)
- Only use USB memory stick recommended.
4. Devices which require additional program
installation may cause identification or data
reading problem.
5. In case of a USB HDD, make sure to connect
an auxiliary power to the USB HDD for proper
operation. 1 primary partitions of a drive is
supported. If there is an extension partition, it
will not be supported.
6. Digital cameras and mobile phones are not
supported.
7. Unsupported or damaged AVI, JPG , MP3 or
SMF files can cause errors. Do not try to
change the file extension of unsupported file
types to the file extension of supported file types.
8. This device codec is hardware codec so the
supportable file format and codec can not be
updated by firmware upgrade.
9. Entry into USB mode can be activated or deactivated by USB key on the remote controller.
10.If you make entry back into USB mode after
switching to RF while playing USB media,
music and movie will be paused. For play,
press GII key to continue to play.
11.Customers should note that permission is
required in order to download MP3 or movie
files from internet. Our company has no right
to grant such permission.Permission should
always be sought from the copyright owner.
OK
SYSTEM SETUP
Select the SUBTITLE LANG
- The menus can be shown on the screen in the
selected language. First select your language.
- When selecting SUBTITLE LANG,it will only
display in English.But subtitle can display in the
language which you selected.
1. Press the USB button and then use F / G
button to select the Setup.
2. Press the OK button to enter the Setup menu.
3. Press the D / E button to select the SYSTEMSETUP.
SYSTEM SETUP
ENGLISH
SUBTITLE LANG
FRENCH
S/W VERSION
ARABIC
DEFAULT
URDU
FARSI
OK
/ESC
4. Press the G and then use D / E button to
select SUBTITLE LANG.
5. Press the G and then use D / E button to
select the desired language.
6. Press the USB button to exit or press the
A/ESC button to return to the USB menu.
Press the Menu button to return to the TV menu.
Select the S/W Version
1. Press the USB button and then use F / G
button to select the Setup.
2. Press the OK button to enter the Setup menu.
3. Press the D / E button to select the SYSTEMSETUP.
4. Press the G and then use D / E button to
select S/W VERSION.
5. Press the G.
6. Press the USB button to exit or press the
A/ESC button to return to the USB menu.
Press the Menu button to return to the TV menu.
Select the Default
- Use the Default option to initialize the adjusted
settings.
1. Press the USB button and then useF / G
button to select the Setup.
2. Press the OK button to enter the Setup menu.
3. Press the D / E button to select the SYSTEMSETUP.
4. Press the G and then use D / E button to
select DEFAULT.
5. Press the G.
6. Press the USB button to exit or press the
A/ESC button to return to the USB menu.
Press the Menu button to return to the TV menu.
7
PHOTO SETUP
Select the Effect
-The picture display effect for the slide show.
-The playing mode of some files in special format
is from top to bottom.
Select the Music
PHOTO SETUP
RANDOM]
EFFECT
WIPE BOTTOM
FREQUENCY
WIPE LEFT
MUSIC
WIPE RIGHT
PLAY MODE
OK
5. Press the G and then use D / E button to
select the Frequency.
6. Press the USB button to exit or press the
A/ESC button to return to the USB menu.
LEFT TOP
/ESC
1. Press the USB button and then use F / G
button to select the Setup.
2. Press the OK button to enter the Setup menu.
3. Press the D / E button to select the PHOTO SETUP.
4. Press the G and then use D / E button to
select EFFECT.
5. Press the G and then use D / E button to
select the desired Effect.
6. Press the USB button to exit or press the
A/ESC button to return to the USB menu.
Select the Frequency
-The picture display interval for the slide show.
1. Press the USB button and then use F / G
button to select the Setup.
2. Press the OK button to enter the Setup menu.
3. Press the D / E button to select the PHOTO SETUP.
4. Press the G and then use D / E button to
select FREQUENCY.
- You can turn on or off the background music
when playing the photograph mode.
- The background music is from USB memory.
1. Press the USB button and then use F / G
button to select the Setup.
2. Press the OK button to enter the Setup menu.
3. Press the D / E button to select the PHOTO SETUP.
4. Press the G and then use D / E button to
select MUSIC.
5. Press the G and then use D / E button to
select ON or OFF.
6. Press the USB button to exit or press the
A/ESC button to return to the USB menu.
Select the Play Mode
-You can select your desired playback mode in
the slide shows.
1. Press the USB button and then use F / G
button to select the Setup.
2. Press the OK button to enter the Setup menu.
3. Press the D / E button to select the PHOTO SETUP.
4. Press the G and then use F / G button to
select PLAY MODE.
5. Press the G and then use D / E button to
select NORMAL or RANDOM.
6. Press the USB button to exit or press the
A/ESC button to return to the USB menu.
MOVIE Media
Select the MOVIE, MUSIC or PHOTO Media
- When you plug a USB or press the USB button,
the below screens will be displayed.
1. Press F / G button to select Movie,
Music or Photo.
2. Press the OK button to enter the
Movie, Music or Photo media.
3. Press the USB button to exit.
Movie File Playing Operation
1. Press the USB button and then useF /G
button to select the Movie.
2. Press the OK button.
3. Press the D / E / F / G button to select
folder and desired movie file.
4. Press the GII(alternative play)orOK (single
play) button.Then the movie starts.
5. Press the USB button to exit or press
A/ESC button to stop or return to the USB
main menu.
Notes:
1.Movie (AVI)file compatibility with this player is
limited as follows :
-Available resolution of AVI file is under
720x480(576)pixel.
-If video codec is not supportable, "UNSUP
PORTED FORMAT"OSD will be displayed in
the file list menu.
-If sound codec is not supportable, Video may
display but "UNSUPPORTED FORMAT" OSD
will be displayed with no sound.
8
-If sound has no data stream,
"NO SOUND"OSD will be displayed on the screen.
-If the number of the screen frame is over 30
per 1 second, this device may not operate normally.
2.Supportable Subtitle format: srt, sri, smi, txt,
ssa,ass, sub, psb
3.Supportable movie file extension: “.DAT”,
“.AVI”, “.MP4”, “.MPG”
4.Supportable video codec: MPEG1(VCD 1.0,
1.1,2.0, SVCD),MPEG4 ASP or Compatible codecs.
Using the remote control
2
1
4
6
S
5
Still screen is displayed. (When playing movie)
Play movie in sequence (at movie list)
8
9
7
To increase or decrease volume level for the
Movie.
Press the 4 button to jump previous Movie.
Press
the 6 button to jump next Movie.
.
Stop movie playing or move to the movie file list
menu.
Press the
Press the
7
9
button to rewind.
button to fast forward.
Show the Information of movie. (when playing movie)
Play movie selected by cursor. (at movie list)
S
ON/OFF or Select subtitle
MUSIC Media
MP3 File Playing Operation
- Purchased MP3/music files may contain copy
right restrictions.
<G-AUDIO>
AUD
AUD
AUD
AUD
AUD
G-AUDIO
D-FILE
ENTER
OK
-1A.MP3
-1B.MP3
-1C.MP3
-3A.MP3
-3B.MP3
/ESC
1. Press the USB button and then use
F / G button to select the Music.
2. Press the OK button.
3. Press the D / E / F / G button to select
folder and desired music file.
4. Press the GII (alternative play) or
OK (single play)button. Then the
music starts.
5. Press the USB button to exit or press the
A/ESC button to stop or return to the USB
menu.
- File name should have a maximum of 8
letters and must incorporate an .mp3 extension.
- Total number of files on the USB memory
device should be less than 1200.
2.This TV mp3 player requires mp3 files to meet
certain technical standards (ISO/IEC
111723,ISO/IEC 13818-3.2)in order to achieve
optimal playback quality.
3.There are many different types of MP3
encoders and these require certain pre-existing
conditions above to ensure compatible play back.
4.The navigation key can be shifted only up and
down during MP3 file play and cannot switch to
other folder.
5.In order to play a file in other folder, stop the
file being played, and move cursor to another folder.
6.In case of VBR(Variable Bit Rate)MP3,
estimated playing time may not correct as
actual playing.
1
2
4
6
S
9
Using the remote control
8
Notes :
1. MP3 compatibility with this player is limited as follows:
- Sampling frequency :within 8 -48 KHz
- Bit rate :32 -384 Kbps, Support all variable bit rates
- TV can not read an MP3 file that has a file
extension other than “.mp3”
Press the
Press the
4
6
button to jump previous music.
button to jump next music.
Moved the Folders in menu. (at music list)
Stop playing music. (when playing music)
5
7
To increase or decrease volume level
for the Music.
Press the
Press the
7
9
button to jump backforward.
button to jump forward.
To pause playback.(when playing music)
Play music in sequence (at music list)
Play music selected by cursor.
PHOTO Media
JPEG File Viewing Options
- When you select Photo in entry menu, you will
now see a screen filled with thumbnail photo
media.
Slide Show
K-REA-1. JPG 81K 720x576
1. K-REA-1<81K>
2. A-NLTM-<154K>
4. K-REA-1 <81K>
1. Press the USB button and then use F / G
button to select the Photo.
2. Press the OK button.
3. Press the D / E / F / G button to select
photo file.
4. Press the OK button for 1 picture display
and press 8 for slide show.
5. Press the USB button to exit or press the
A/ESC button to stop slide show or return to
thumbnail file list, USB main menu.
5. A-NLTM-1<154K>
OK
3. B-RED<43K>
6. B-RED <43K>
/ESC
1. Press the D / E / F / G button to select
JPEG file and then press the 8 button. Slide
show starts.
2. You can choose the slide show effect,
frequency and play mode in the USB Setup.
3. Press the GII button to pause the current
image.
4. Press the USB button to exit or press the
A/ESC button to stop slide show return to the
USB menu.
9
PHOTO Media
Still picture
Press the D/E / F/G button to select JPEG file
then press the OK button. Selected still picture
display starts.
2
1
4
Using the remote control
6
S
Notes :
1.JPEG compatibility with this player is limited as
follows :
- Depending upon the size and the number of
JPEG files,it could take a long time for TV to
read the USB memory's contents. If you don't
see an on screen display after several
minutes,some of the files maybe too largereduce the resolution of the JPEG files to less
than 2M pixels as 2760x2048 resolution.
- The total number of files and folders on the
USB memory device should be less than 1200.
- File name without ".jpg" extension will not be
able to read by this TV jpeg decoder. Even
though the files are shown as JPEG image files
in Windows Explorer.
- Cause of Photo character, Progressive JPEG is
always scanned “WIPETOP” regardless of
Photo Effect.
Move to main menu from thumbnail mode.
5
9
7
3
To increase or decrease volume level for the
Music.(When selecting the turn-on of back
ground music when playing the photograph
mode.)
To select the previous or next page. (at thumbnail mode)
To jump to the previous or next photo(at one photo display)
These keys (FF&RW) are not available in photo
mode.
To enlarge or reduce the image 2, 3 or 4
times. (at one photo display)
1.Zoom mode
To scroll left, right, up and down.
2.Still picture display mode
VOL+:Rotate 90 (Clockwise)
VOL- : Rotate-90 (Counter-clokwise)
CH+:Upside down&vice versa
CH-:Mirror imgame&versa
GAME Media
Using the remote control
1
2
4
6
OK
To increase or decrease volume level for the
game.
Press the
Press the
4
6
button to jump previous Game.
button to jump next Game.
S
GAME File Playing Operation
1. Press the USB button and then use D / E /
F / G button to select the Game.
2. Press the OK button.
3. Press the D / E / F / G button to select
folder and desired game file.
4. Press the G (alternative play) or OK(single
play)button.Then the game starts.
5. Press the USB button to exit or press the
A/ESC button to stop or return to the USB menu.
10
5
Stop game playing or move to the game file list menu.
Play game in sequence (at game list)
8
Play game seleced by cursor.
To confirm(when playing game)
To select left,right,up,down
(when playing game)
Note:
-You can download the game file from
www.gamefortv.com.The downloaded files are
compressed files, so please decompress files
and then put them in usb before using them.
-If the files under the folder in USB exceed 5
floors,maybe you can’t open game files.
Teletext (option)
Teletext (or TOP text) is an optional function,
therefore only a set with the teletext system can
receive the teletext broadcast.
Teletext is a free service broadcast by most TV
stations which gives up-to-the-minute information
on news, weather, television programmes, share
prices and many other topics.
The teletext decoder of this TV can support the
SIMPLE, TOP and FASTEXT systems. SIMPLE
(standard teletext) consists of a number of pages
which are selected by directly entering the corresponding page number. TOP and FASTEXT are
more modern methods allowing quick and easy
selection of teletext information.
Switch on/off
Press the TEXT button to switch to teletext.
The initial page or last page appears on the
screen.Two page numbers, TV station name, date
and time are displayed on the screen headline.
The first page number indicates your selection,
while the second shows the current page displayed.Press the TEXTor TV/AV button to switch
off teletext. The previous mode reappears.
SIMPLE text
Page selection
1. Enter the desired page number as a three digit
number with the NUMBER buttons. If during
selection you press a wrong number, you
must complete the three digit number and
then re-enter the correct page number.
2. The D / E button can be used to select the
preceding or following page.
Programming a colour button in LIST mode (option)
Press the M button to switch to LIST mode.
Four teletext page numbers of your choice can be
colour coded and easily selected by pressing the
corresponding coloured button on the remote control handset.
1. Press a coloured button.
2. Using the NUMBER buttons, select the page
you wish to programme.
3. Press the OK button. Then the selected page
is stored as the selected page number with
blinking once. From now on, you can select
this page with the same coloured button.
4. The three other coloured buttons are programmed in the same way.
TOP text (option)
The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next group and the blue field
indicates the next block.
Block / group / page selection
1. With the blue button you can progress from
block to block.
2. Use the yellow button to proceed to the next
group with automatic overflow to the next block.
3. With the green button you can proceed to the
next existing page with automatic overflow to
the next group.
Alternatively the D button can be used.
4. The red button permits to return to previous
selection. Alternatively the E button can be used.
Direct page selection
Corresponding to the SIMPLE teletext mode, you
can select a page by entering it as a three digit
number using the NUMBER buttons in TOP mode.
FASTEXT
The teletext pages are colour coded along the bottom of the screen and are selected by pressing
the corresponding coloured button.
Page selection
1. Press the i button to select the index page.
2. You can select the pages which are colour
coded along the bottom line with the same
coloured buttons.
3. Corresponding to the SIMPLE teletext mode,
you can select a page by entering its three
digit page number with the NUMBER buttons
in FASTEXT mode.
4. The D / E button can be used to select the
preceding or following page.
Special teletext functions
REVEAL
Press this button to display concealed information, such as solutions of riddles or puzzles.
Press this button again to remove the information
from the display.
SIZE
Selects double height text.
Press this button to enlarge the top half of the
page.Press this button again to enlarge the bottom half of the page.Press this button again to
return to the normal display.
UPDATE
Displays the TV picture on the screen while waiting
for the new teletext page. The update symbol will
appear at the top left hand corner of the screen. When
the updated page is available then the update symbol
will change to the page number. Press this button to
view the updated teletext page.
HOLD
Stops the automatic page change which will occur
if a teletext page consists of 2 or more sub pages.
The number of sub pages and the sub page displayed is, usually, shown on the screen below the
time. When this button is pressed the stop symbol
is displayed at the top left-hand corner of the
screen and the automatic page change is inhibited.To continue press this button again.
MIX
Displays the teletext pages superimposed on the
TV picture.To switch the TV picture off press this
button again.
TIME
When viewing a TV programme, press this button to
display the time at the top right hand corner of the
screen. Press this button again to remove the display.
In the teletext mode, press this button to select a sub
page number. The sub page number is displayed at
the bottom of the screen. To hold or change the sub
page, press the RED/GREEN, D / E or NUMBER
buttons. Press again to exit this function.
11
Troubleshooting check list
Symptoms
No picture, no sound
Sound OK, poor picture
Picture OK, poor sound
Picture blurred
Lines or streaks in picture
Poor reception on some channels
No colour
Poor colour
Remote control does not work
Check these items and try to
adjust these
The mains plug-(plugged in and
switched on)
Is the TV switched on
Try another channel (weak signal)
Check aerial (plugged into TV?)
Check aerial (broken lead?)
Check aerial
Check for local interference
Adjust contrast
Adjust brightness
Adjust colour
Adjust volume
Check the batteries in remote control
Check Audio/Video sockets (VCR only)
Download PDF