LG | 42LB6700 | LG 42LB6500 Owner’s Manual

OWNER’S MANUAL
LED TV*
* Disclaimer
LG LED TV applies LCD
screen with LED backlights.
Click! User Guide
Please read this manual carefully before operating
your set and retain it for future reference.
LB63**
LB65**
LB67**
LB69**
LB72**
LB75**
LB87**
P/NO : MFL68027173 (1401-REV01)
TABLE OF CONTENTS
3
Licenses
41
REMOTE CONTROL
3
OPEN SOURCE SOFTWARE
NOTICE
42
Magic Remote Functions
43
43
44
Registering Magic Remote
How to use Magic Remote
Precautions to Take when Using the
Magic Remote
44
Using the User guide
45
MAINTENANCE
45
45
45
Cleaning your TV
- Screen, frame, cabinet and stand
- Power cord
45
TROUBLESHOOTING
47
SPECIFICATIONS
3
EXTERNAl CONTROL DEVICE
SETUP
4
Safety Instructions
10
Viewing 3D Imaging (Only 3D models)
11
Installation Procedure
11
ASSEMBLING AND PREPARING
11
15
16
18
19
20
20
24
25
27
28
30
30
31
31
Unpacking
Separate purchase
Parts and buttons
- Using the Joystick button
Lifting and moving the TV
Setting up the TV
- Attaching the stand
- Attaching the Sound Bar Supporter
Mounting on a table
Mounting on a wall
Tidying cables
Using Built-in Camera
- Preparing Built-in Camera
- Name of Parts of Built-in Camera
- Checking the Camera’s Shooting
Range
32
MAKING CONNECTIONS
32
33
33
34
35
36
37
38
38
38
39
40
Antenna connection
Satellite dish connection
Headphone connection
HDMI connection
DVI to HDMI connection
Component connection
Composite connection
Audio connection
- Digital optical audio connection
USB connection
Euro Scart connection
MHL connection
WARNING
yy If you ignore the warning message, you
may be seriously injured or there is a
possibility of accident or death.
CAUTION
yy If you ignore the caution message, you
may be slightly injured or the product may
be damaged.
NOTE
yy The note helps you understand and use
the product safely. Please read the note
carefully before using the product.
ENGLISH
ENG
TABLE OF CONTENTS
2
3
LICENSES / OPEN SOURCE SOFTWARE NOTICE / EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
SAFETY INSTRUCTIONS
4
Please read these safety precautions carefully before using the product.
WARNING
yyDo not place the TV and/or remote control
in the following environments:
--A location exposed to direct sunlight
--An area with high humidity such as a
bathroom
--Near any heat source such as stoves and
other devices that produce heat
--Near kitchen counters or humidifiers
where they can easily be exposed to
steam or oil
--An area exposed to rain or wind
--Near containers of water such as vases
Otherwise, this may result in fire, electric
shock, malfunction or product deformation.
yyDo not place the product where it might be
exposed to dust.
This may cause a fire hazard.
yyMains Plug is the TV connecting/
disconnecting device to AC mains electric
supply. This plug must remain readily
attached and operable when TV is in use.
yyDo not touch the power plug with wet
hands. Additionally, if the cord pin is wet
or covered with dust, dry the power plug
completely or wipe dust off.
You may be electrocuted due to excess
moisture.
yyMake sure to connect Mains cable to
compliant AC mains socket with Grounded
earth pin. (Except for devices which are not
grounded on earth.) Otherwise possibility you
may be electrocuted or injured.
yyInsert power cable plug completely into wall
socket otherwise if not secured completely
into socket, fire ignition may break out.
yyEnsure the power cord does not come into
contact with hot objects such as a heater.
This may cause a fire or an electric shock
hazard.
yyDo not place a heavy object, or the product
itself, on power cables.
Otherwise, this may result in fire or electric
shock.
yyBend antenna cable between inside and
outside building to prevent rain from flowing
in.
This may cause water damaged inside the
Product and could give an electric shock.
ENGLISH
ENG
Safety Instructions
5
SAFETY INSTRUCTIONS
ENGLISH
yyWhen mounting TV onto wall make sure to
neatly install and isolate cabling from rear
of TV as to not create possibility of electric
shock /fire hazard.
yyDo not plug too many electrical devices into
a single multiple electrical outlet.
Otherwise, this may result in fire due to
over-heating.
yyDo not drop the product or let it fall over
when connecting external devices.
Otherwise, this may result in injury or
damage to the product.
yyKeep the anti-moisture packing material or
vinyl packing out of the reach of children.
Anti-moisture material is harmful if
swallowed. If swallowed by mistake, force
the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can
cause suffocation. Keep it out of the reach
of children.
yyDispose of used batteries carefully to
ensure that a small child does not consume
them. Please seek Doctor- Medical Attention
immediately if child consumes batteries.
yyDo not insert any metal objects/conductors
(like a metal chopstick/cutlery/screwdriver)
between power cable plug and input Wall
Socket while it is connected to the input
terminal on the wall. Additionally, do not
touch the power cable right after plugging
into the wall input terminal. You may be
electrocuted. (Depending on model)
yyDo not put or store inflammable substances
near the product. There is a danger of
combustion/explosion or fire due to careless
handling of the inflammable substances.
yyDo not drop metallic objects such as
coins, hair pins, chopsticks or wire into
the product, or inflammable objects such
as paper and matches. Children must pay
particular attention. Electrical shock, fire
or injury can occur. If a foreign object is
dropped into the product, unplug the power
cord and contact the service centre.
Desic
cant
yyDo not let your children climb or cling onto
the TV. Otherwise, the TV may fall over,
which may cause serious injury.
yyDo not spray water on the product or scrub
with an inflammable substance (thinner or
benzene). Fire or electric shock accident
can occur.
SAFETY INSTRUCTIONS
6
yyUnplug the TV from AC mains wall socket
if you do not intend to use the TV for a long
period of time. Accumulated dust can cause
fire hazard and insulation deterioration can
cause electric leakage/shock/fire.
yyNever touch this product or antenna during
a thunder or lighting storm.
You may be electrocuted.
yyApparatus shall not be exposed to dripping
or splashing and no objects filled with
liquids, such as vases, shall be placed on
the apparatus.
yyNever touch the wall outlet when there is
leakage of gas, open the windows and
ventilate.
It may cause a fire or a burn by a spark.
yyDo not install this product on a wall if it
could be exposed to oil or oil mist.
This may damage the product and causeit
to fall.
CAUTION
yyDo not disassemble, repair or modify the
product at your own discretion.
Fire or electric shock accident can occur.
Contact the service centre for check,
calibration or repair.
yyIf any of the following occur, unplug the
product immediately and contact your local
service centre.
--The product has been impacted by shock
--The product has been damaged
--Foreign objects have entered the product
--The product produced smoke or a strange
smell
This may result in fire or electric shock.
yyInstall the product where no radio wave
occurs.
yyThere should be enough distance between
an outside antenna and power lines to
keep the former from touching the latter
even when the antenna falls.
This may cause an electric shock.
yyDo not install the product on places such
as unstable shelves or inclined surfaces.
Also avoid places where there is vibration
or where the product cannot be fully
supported. Otherwise, the product may
fall or flip over, which may cause injury or
damage to the product.
ENGLISH
ENG
yyDo not allow any impact, shock or any
objects to fall into the unit, and do not drop
anything onto the screen.
You may be injured or the product can be
damaged.
7
SAFETY INSTRUCTIONS
ENGLISH
ENG
yyIf you install the TV on a stand, you need
to take actions to prevent the product from
overturning. Otherwise, the product may fall
over, which may cause injury.
yyIf you intend to mount the product to a wall,
attach VESA standard mounting interface
(optional parts) to the back of the product.
When you install the set to use the wall
mounting bracket (optional parts), fix it
carefully so as not to drop.
yyOnly use the attachments / accessories
specified by the manufacturer.
yyWhen installing the antenna, consult with a
qualified service technician. If not installed
by a qualified technician, this may create a
fire hazard or an electric shock hazard.
yyWe recommend that you maintain a
distance of at least 2 to 7 times the diagonal
screen size when watching TV.
If you watch TV for a long period of time,
this may cause blurred vision.
yyOnly use the specified type of battery.
This could cause damage to the remote
control.
yyDo not mix new batteries with old batteries.
This may cause the batteries to overheat
and leak.
yyBatteries should not be exposed to
excessive heat. For example, keep away
from direct Sunlight, open fireplace and
electric heaters.
yyDo not place non-rechargeable batteries in
charging device.
yyMake sure there are no objects between the
remote control and its sensor.
yySignal from Remote Control can be
interrupted due to external/internal lighting
eg Sunlight, fluorescent lighting.If this
occurs turn off lighting or darken viewing
area.
yyWhen connecting external devices such
as video game consoles, make sure the
connecting cables are long enough.
Otherwise, the product may fall over, which
may cause injury or damage the product.
yyDo not turn the product On/Off by pluggingin or unplugging the power plug to the
wall outlet. (Do not use the power plug for
switch.)
It may cause mechanical failure or could
give an electric shock.
yyPlease follow the installation instructions
below to prevent the product from
overheating.
--The distance between the product and the
wall should be more than 10 cm.
--Do not install the product in a place with
no ventilation (e.g., on a bookshelf or in a
cupboard).
--Do not install the product on a carpet or
cushion.
--Make sure the air vent is not blocked by a
tablecloth or curtain.
Otherwise, this may result in fire.
SAFETY INSTRUCTIONS
yyPeriodically examine the cord of your
appliance, and if its appearance indicates
damage or deterioration, unplug it,
discontinue use of the appliance, and have
the cord replaced with an exact replacement
part by an authorized servicer.
yyPrevent dust collecting on the power plug
pins or outlet.
This may cause a fire hazard.
yyProtect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits
the appliance.
yyDo not press strongly upon the panel with
a hand or sharp object such as nail, pencil
or pen, or make a scratch on it, as it may
cause damage to screen.
yyAvoid touching the screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary or
permanent distortion/damage to screen.
yyWhen cleaning the product and its
components, unplug the power first
and wipe it with a soft cloth. Applying
excessive force may cause scratches or
discolouration. Do not spray with water
or wipe with a wet cloth. Never use glass
cleaner, car or industrial shiner, abrasives
or wax, benzene, alcohol etc., which can
damage the product and its panel.
Otherwise, this may result in fire, electric
shock or product damage (deformation,
corrosion or breakage).
yyAs long as this unit is connected to the AC
wall outlet, it is not disconnected from the
AC power source even if you turn off this
unit by SWITCH.
yyWhen unplugging the cable, grab the plug
and unplug it, by pulling at the plug. Don’t
pull at the cord to unplug the power cord
from the power board, as this could be
hazardous.
yyWhen moving the product, make sure
you turn the power off first. Then, unplug
the power cables, antenna cables and all
connecting cables.
The TV set or power cord may be
damaged, which may create a fire hazard
or cause electric shock.
yyWhen moving or unpacking the product,
work in pairs because the product is heavy.
Otherwise, this may result in injury.
ENGLISH
ENG
yyTake care not to touch the ventilation
openings when watching the TV for long
periods as the ventilation openings may
become hot. This does not affect the
operation or performance of the product.
8
9
SAFETY INSTRUCTIONS
ENGLISH
ENG
yyContact the service centre once a year to
clean the internal parts of the product.
Accumulated dust can cause mechanical
failure.
yyRefer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
yyIf the product feels cold to the touch, there
may be a small “flicker” when it is turned on.
This is normal, there is nothing wrong with
product.
yyThe panel is a high technology display
product with resolution of two million to six
million pixels. You may see tiny black dots
and/or brightly coloured dots (red, blue or
green) at a size of 1 ppm on the panel. This
does not indicate a malfunction and does
not affect the performance and reliability of
the product.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
yyYou may find different brightness and colour
of the panel depending on your viewing
position(left/right/top/down).
This phenomenon occurs due to the
characteristic of the panel. It is not related
with the product performance, and it is not
malfunction.
yyDisplaying a still image (e.g., broadcasting
channel logo, on-screen menu, scene from
a video game) for a prolonged time may
cause damage to the screen, resulting in
retention of the image, which is known as
image sticking. The warranty does not cover
the product for image sticking.
Avoid displaying a fixed image on your
television’s screen for a prolonged period (2
or more hours for LCD, 1 or more hours for
Plasma).
Also, if you watch the TV at a ratio of 4:3 for
a long time, image sticking may occur on
the borders of the panel.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
yyGenerated Sound
“Cracking” noise: A cracking noise that
occurs when watching or turning off the TV
is generated by plastic thermal contraction
due to tempera-ture and humidity. This
noise is common for products where
thermal deformation is required. Electrical
circuit humming/panel buzzing: A low level
noise is generated from a high-speed
switching circuit, which supplies a large
amount of current to operate a product. It
varies depend-ing on the product.
This generated sound does not affect the
performance and reliability of the product.
SAFETY INSTRUCTIONS
WARNING
Viewing Environment
yy Viewing Time
-- When watching 3D contents, take 5 - 15
minute breaks every hour. Viewing 3D
contents for a long period of time may
cause headache, dizziness, fatigue or
eye strain.
Those that have a photosensitive
seizure or chronic illness
yy Some users may experience a seizure or
other abnormal symptoms when they are
exposed to a flashing light or particular
pattern from 3D contents.
yy Do not watch 3D videos if you feel nausea,
are pregnant and/ or have a chronic illness
such as epilepsy, cardiac disorder, or blood
pressure disease, etc.
yy 3D Contents are not recommended to those
who suffer from stereo blindness or stereo
anomaly. Double images or discomfort in
viewing may be experienced.
yy If you have strabismus (cross-eyed),
amblyopia (weak eyesight) or astigmatism,
you may have trouble sensing depth and
easily feel fatigue due to double images. It
is advised to take frequent breaks than the
average adult.
yy If your eyesight varies between your right
and left eye, revise your eyesight prior to
watching 3D contents.
CAUTION
Viewing Environment
� Viewing Distance
- Maintain a distance of at least twice the
screen diagonal length when watching 3D
contents. If you feel discomfort in viewing
3D contents, move further away from the
TV.
Viewing Age
yy Infants/Children
-- Usage/ Viewing 3D contents for children
under the age of 5 are prohibited.
-- Children under the age of 10 may
overreact and become overly excited
because their vision is in development (for
example: trying to touch the screen or
trying to jump into it. Special monitoring
and extra attention is required for children
watching 3D contents.
-- Children have greater binocular disparity
of 3D presentations than adults because
the distance between the eyes is shorter
than one of adults. Therefore they will
perceive more stereoscopic depth
compared to adults for the same 3D
image.
yy Teenagers
-- Teenagers under the age of 19 may
react with sensitivity due to stimulation
from light in 3D contents. Advise them to
refrain from watching 3D contens for a
long time when they are tired.
yy Elderly
-- The elderly may perceive less 3D
effect compared to the youth. Do not sit
closer to the TV than the recommended
distance.
Symptoms which require discontinuation or
refraining from watching 3D contents
yy Do not watch 3D contents when you feel
fatigue from lack of sleep, overwork or
drinking.
yy When these symptoms are experienced,
stop using/watching 3D contents and get
enough rest until the symptom subsides.
-- Consult your doctor when the symptoms
persist. Symptoms may include
headache, eyeball pain, dizziness,
nausea, palpitation, blurriness,
discomfort, double image, visual
inconvenience or fatigue.
Cautions when using the 3D glasses
� Make sure to use LG 3D glasses. Otherwise,
you may not be able to view 3D videos
properly.
� Do not use 3D glasses instead of your normal
glasses, sunglasses or protective goggles.
� Using modified 3D glasses may cause eye
strain or image distortion.
� Do not keep your 3D glasses in extremely high
or low temperatures. It will cause deformation.
� The 3D glasses are fragile and are easy to be
scratched. Always use a soft, clean piece of
cloth when wiping the lenses. Do not scratch
the lenses of the 3D glasses with sharp
objects or clean/wipe them with chemicals.
ENGLISH
ENG
Viewing 3D Imaging
(Only 3D models)
10
11
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
ENGLISH
ENG
NOTE
yy Image shown may differ from your TV.
yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yy The available menus and options may differ from the input source or product model that you
are using.
yy New features may be added to this TV in the future.
yy The TV can be placed in standby mode in order to reduce the power consumption. And the
TV should be turned off if it will not be watched for some time, as this will reduce energy
consumption.
yy The energy consumed during use can be significantly reduced if the level of brightness of the
picture is reduced, and this will reduce the overall running cost.
Installation Procedure
1
2
3
4
Open the package and make sure all the accessories are included.
Attach the stand to the TV set.
Connect an external device to the TV set.
Make sure the network connection is available.
You can use the TV network functions only when the network connection is made.
* If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV
may take up to one minute.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
CAUTION
yy Do not use any unapproved items to ensure the safety and product life span.
yy Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
yy Some models have a thin film attached on to the screen and this must not be removed.
NOTE
yy The items supplied with your product may vary depending on the model.
yy Product specifications or contents of this manual may be changed without prior notice due to
upgrade of product functions.
yy For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm
thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV’s USB port.
B
B
A
*A <
= 10 mm
A
*B <
= 18 mm
ASSEMBLING AND PREPARING
12
ENGLISH
ENG
ENERGY AV MODE INPUT
TV
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
6
7
8
9
0
FLASHBK
SAVING
1
MARK
9
0
FLASHBK
3D
P
A
G
E
FAV
VOL
3D
CH
P
A
G
E
MUTE
Q.MENU
MENU INFO
ENTER
BACK
6
MARK
CH
MUTE
MENU INFO
3
5
8
LIST
FAV
VOL
2
4
7
LIST
Q.MENU
ENTER
EXIT
BACK
EXIT
L/R SELECT
L/R SELECT
FREEZE
FREEZE
RATIO
RATIO
Remote Control, Batteries
(AAA)
The remote control will not
be included for all sales
market.
(Depending on model)
(See p.41)
Magic Remote, Batteries
(AA)
(Only LB63**, LB65**, LB67**,
LB69**, LB72**, LB75**,
LB87**)
(See p.42)
Owner’s Manual
Tag on
Cinema 3D Glasses
The number of 3D glasses
may differ depending on the
model or country.
(Only LB65**, LB67**, LB69**,
LB72**, LB75**, LB87**)
Wall Mount Spacers
2EA
(Only 42LB63**, 42LB65**)
(See p.28)
Component Gender Cable
(Only LB87**)
(See p.36)
Composite Gender Cable
(Only LB87**)
(See p.36, 37)
Power Cord
Tag On
13
ASSEMBLING AND PREPARING
ENGLISH
ENG
Cable Holder
(Depending on model)
(See p.28, 29)
Cable Managements
2EA
(Only LB63**, LB65**,
LB67**, LB69**, LB72**)
(See p.28, 29)
Cable Managements
2EA
(Only LB75**)
(See p.29)
Stand Screws
4EA, M4 x L20
(Only 32LB65**)
(See p.20, 21)
Stand Screws
4EA, M4 x L14
(Only LB63**,
39/42/60/70LB65**,
LB67**, LB69**, LB72**,
LB75**)
8EA, M4 x L14
(Only LB87**)
(See p.20, 21, 22, 23, 24)
Stand Screws
4EA, M4 x L10
(Only LB75**)
(See p.21)
Stand Bases
(Only LB65**-TH)
(See p.21)
Stand Bases
(Only LB63**,
32/39/42/47/50/55/60LB65**
-TA/TB)
(See p.20)
Stand Assys
(Stand Body/Stand Base)
(Only 70LB65**-TA, LB67**,
LB69**, LB72**)
(See p.20)
5**)
Stand Screws
4EA, M4 x L12
(Only L47/50/55LB65**)
(See p.20, 21)
ASSEMBLING AND PREPARING
14
ENGLISH
ENG
Stand Front
(Only LB75**)
(See p.21)
Stand Supporters
(Only LB75**)
(See p.21)
Sound Bar
(Only LB87**)
(See p.22, 24)
Stand Assys
(Only LB87**)
(See p.22)
Sound Bar Supporters
(Only LB87**)
(See p.24)
Screw Covers
(Only LB87**)
(See p.23, 24)
15
ASSEMBLING AND PREPARING
ENGLISH
ENG
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
AG-F***DP
Dual Play Glasses
AG-F***
Cinema 3D Glasses
AN-MR500
Magic Remote
Tag on
AN-VC5**
Video Call Camera
LG Audio Device
LB65**, LB67**,
LB69**, LB72**,
LB75**
LB87**
AG-F***DP
Dual Play Glasses
•
•
AG-F***
Cinema 3D Glasses
•
•
Compatibility
LB63**
AN-MR500
Magic Remote
•
•
•
Tag on
•
•
•
AN-VC5**
Video Call Camera
•
•
LG Audio Device
•
•
•
The model name or design may be changed depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
ASSEMBLING AND PREPARING
A type : LB63**, LB65**-TA/TB
ENGLISH
ENG
Parts and buttons
B type : LB65**-TH
Screen
Screen
Speakers
Speakers
Remote control and
Intelligent1 sensors
Power Indicator
Remote control and
Intelligent1 sensors
Power Indicator
Joystick Button2
Joystick Button2
C type : LB67**, LB69**, LB72**
Screen
Speakers
Remote control and
Intelligent1 sensors
Power Indicator
Joystick Button2
16
17
ASSEMBLING AND PREPARING
ENGLISH
ENG
D type : LB75**
E type : LB87**
Screen
Screen
Built-in Camera
Speakers
Speakers
LG Logo light
Remote control and
Intelligent1 sensors
Power Indicator
Remote control and
Intelligent1 sensors
Joystick Button2
Joystick Button2
1 Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment.
2 Joystick Button - This button is located below the TV screen.
NOTE
yy You can set the LG Logo light or Power indicator Light to on or off by selecting OPTION in the
main menus. (Depending on model)
ASSEMBLING AND PREPARING
18
ENG
You can simply operate the TV functions by pressing to turn On/Off or sliding your finger over joystick
button moving up, down, left or right.
Basic Functions
Power On
When the TV is turned off, place your finger on the joystick
button and press it once and release it.
Power Off
When the TV is turned on, place your finger on the joystick
button and press it once for a few seconds and release it.
(However, if the Menu button is on the screen, pressing and
holding the joystick button will let you exit the Menu.
Volume
Control
If you place your finger over the joystick button and move it left
or right, you can adjust the volume level you want.
If you place your finger over the joystick button and move it up
Programmes
or down, you can scrolls through the saved programmes you
Control
want.
NOTE
yy When your finger is over the joystick button and you are sliding finger forward/back, left or right,
be careful not to press down to hard on joystick. If you press down hard on joystick button first
then the adjustment of volume level and programme scroll action will not operate.
Adjusting the Menu
When the TV is turned on, press the joystick button one time.
You can adjust the Menu items( , ,
) moving the joystick button up, down, left or right.
TV Off
Turns the power off.
Close
Closes Clears on-screen displays and returns to
TV viewing.
Input
Changes the input source.
ENGLISH
Using the Joystick button
19
ASSEMBLING AND PREPARING
ENGLISH
Lifting and moving the TV
Please note the following advice to prevent the
TV from being scratched or damaged and for
safe transportation regardless of its type and
size.
yy When transporting a large TV, there should
be at least 2 people.
yy When transporting the TV by hand, hold the
TV as shown in the following illustration.
CAUTION
yy Avoid touching the screen at all times, as
this may result in damage to the screen.
yy It is recommended to move the TV in the
box or packing material that the TV originally
came in.
yy Before moving or lifting the TV, disconnect
the power cord and all cables.
yy When holding the TV, the screen should face
away from you to avoid damage.
yy Hold the top and bottom of the TV frame
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
yy When transporting the TV, do not expose the
TV to jolts or excessive vibration.
yy When transporting the TV, keep the TV
upright, never turn the TV on its side or tilt
towards the left or right.
yy Do not apply excessive pressure to cause
flexing /bending of frame chassis as it may
damage screen.
yy When handling the TV, be careful not to
damage the protruding joystick button.
ASSEMBLING AND PREPARING
Setting up the TV
20
70LB65**-TA, LB67**, LB69**, LB72**
1
ENGLISH
ENG
Image shown may differ from your TV.
Stand Body
Attaching the stand
LB63**, 32/39/42/47/50/55/60LB65**-TA/TB
1
A stand base
Stand Base
A stand base
B stand base
1
B stand base
2
1
2
1 Attach the stand to the TV using the upper
mounting hole on the back of the TV.
2 Attach the stand to the TV using the lower
connection on the back of the TV.
2
1 Attach the stand to the TV using the upper
mounting hole on the back of the TV.
2 Attach the stand to the TV using the lower
connection on the back of the TV.
2
M4 x L14
M4 x L20
(Only 32LB65**)
M4 x L12
4EA (Only 47/50/55LB65**)
M4 x L14
4EA
21
ASSEMBLING AND PREPARING
LB75**
LB65**-TH
ENGLISH
ENG
1
1
A stand base
B stand base
1
2
1
Stand Front
B Stand
Supporter
2
A Stand
Supporter
2
1 Attach the stand to the TV using the upper
mounting hole on the back of the TV.
2 Attach the stand to the TV using the lower
connection on the back of the TV.
M4 x L10
2
4EA
1
2
M4 x L14
M4 x L20
(Only 32LB65**)
M4 x L12
4EA (Only 47/50/55LB65**)
ASSEMBLING AND PREPARING
22
ENG
ENGLISH
LB87**
3
1
Sound Bar
1
Stand Assy Right
Stand Assy Left
2
1 Attach the stand to the TV using the upper
mounting hole on the back of the TV.
2 Attach the stand to the TV using the lower
connection on the back of the TV.
M4 x L14
4EA
4
2
M4 x L14
4EA
23
ASSEMBLING AND PREPARING
ENGLISH
3
CAUTION
yy When attaching the stand to the TV
set, place the screen facing down on a
cushioned table or flat surface to protect
the screen from scratches.
yy Make sure that the screws are fastened
completely. (If they are not fastened
securely enough, the TV may tilt forward
after being installed.)
Do not use too much force and over
tighten the screws; otherwise screw may
be damaged and not tighten correctly.
NOTE
M4 x L14
4EA
4
Screw Cover
yy Remove the stand before installing the
TV on a wall mount by performing the
stand attachment in reverse.
yy Screw Cover will protect the opening from
accumulating dust and dirty.
ASSEMBLING AND PREPARING
ENG
(In case of mounting on a wall)
3
ENGLISH
Attaching the Sound Bar Supporter
LB87**
1
Sound Bar
Sound Bar Supporter
Right
Sound Bar Supporter
Left
M4 x L14
M4 x L14
4EA
4EA
4
2
24
Screw Cover
25
ASSEMBLING AND PREPARING
ENGLISH
ENG
Using the Kensington security system
CAUTION
yy When attaching the Sound Bar Supporter
to the TV set, place the screen facing
down on a cushioned table or flat surface
to protect the screen from scratches.
yy Make sure that the screws are inserted
correctly and fastened securely. (If they
are not fastened securely enough, the TV
may tilt forward after being installed.)
Do not use too much force and over
tighten the screws; otherwise screw may
be damaged and not tighten correctly.
yy The sound bar supporter only uses for
wall mounting.
(This feature is available depending on models.)
yy Image shown may differ from your TV.
The Kensington security system connector
is located at the rear of the TV. For more
information of installation and using, refer to the
manual provided with the Kensington security
system or visit http://www.kensington.com.
Connect the Kensington security system cable
between the TV and a table.
NOTE
yy Remove the Sound Bar Supporter before
installing the stand by performing the
stand attachment in reverse.
yy Screw Cover will protect the opening from
accumulating dust and dirty.
Mounting on a table
CAUTION
1 Lift and tilt the TV into its upright position on
a table.
-- Leave a 10 cm (minimum) space from
the wall for proper ventilation.
yy Do not place the TV near or on sources
of heat, as this may result in fire or other
damage.
CAUTION
y Make sure that children do not climb on
or hang on the TV.
10 cm
m
10 c
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
NOTE
y Use a platform or cabinet that is strong
and large enough to support the TV
securely.
y Brackets, bolts and ropes are not
provided. You can obtain additional
accessories from your local dealer.
ASSEMBLING AND PREPARING
26
(This feature is not available for all models.)
yy If a television is not positioned in a
sufficiently stable location, it can be
potentially hazardous due to falling. Many
injuries, particularly to children, can be
avoided by taking simple precautions
such as:
»» Using cabinets or stands
recommended by the manufacturer of
the television.
»» Only using furniture that can safely
support the television.
»» Ensuring the television is not
overhanging the edge of the
supporting furniture.
»» Not placing the television on tall
furniture (for example, cupboards or
bookcases) without anchoring both
the furniture and the television to a
suitable support.
»» Not standing the televisions on cloth
or other materials placed between the
television and supporting furniture.
»» Educating children about the dangers
of climbing on furniture to reach the
television or its controls.
1 Insert and tighten the eye-bolts, or TV
brackets and bolts on the back of the TV.
-- If there are bolts inserted at the eyebolts position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and
the eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets
tightly with a sturdy rope.
Make sure to keep the rope horizontal with
the flat surface.
ENGLISH
ENG
Securing the TV to a wall
WARNING
27
ASSEMBLING AND PREPARING
ENGLISH
ENG
Mounting on a wall
Attach an optional wall mount bracket at the rear
of the TV carefully and install the wall mount
bracket on a solid wall perpendicular to the
floor. When you attach the TV to other building
materials, please contact qualified personnel.
LG recommends that wall mounting be
performed by a qualified professional installer.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described
in the following table.
(Wall Mounting Bracket)
Model
32/39LB65**
VESA (A x B)
Standard screw
Number of
screws
Model
200 x 200
M6
4
60LB65**
42/47/50/55LB67**
42/47/55LB69**
42/47/55/60/65LB72**
42/47/55/60/65LB75**
60LB87**
VESA (A x B) 400 x 400
Standard screw M6
Number of
4
screws
42/47/55LB63**
42/47/50/55LB65**
49/55LB87**
400 x 400
M6
4
70LB65**
600 x 400
M6
4
CAUTION
yy Disconnect the power first, and then
move or install the TV. Otherwise electric
shock may occur.
yy If you install the TV on a ceiling or slanted
wall, it may fall and result in severe injury.
Use an authorised LG wall mount and
contact the local dealer or qualified
personnel.
yy Do not over tighten the screws as this
may cause damage to the TV and void
your warranty.
yy Use the screws and wall mounts that
meet the VESA standard. Any damages
or injuries by misuse or using an
improper accessory are not covered by
the manufacturer’s warranty.
ASSEMBLING AND PREPARING
yy Use the screws that are listed on the
VESA standard screw specifications.
yy The wall mount kit includes an installation
manual and necessary parts.
yy The wall mount bracket is not provided.
You can obtain additional accessories
from your local dealer.
yy The length of screws may differ
depending on the wall mount. Make sure
to use the proper length.
yy For more information, refer to the manual
supplied with the wall mount.
yy When attaching a wall mounting bracket
to the TV, insert the wall mount spacers
into the TV wall mount holes to adjust the
vertical angle of the TV. (Only 42LB63**,
42LB65**)
Tidying cables
Image shown may differ from your TV.
1 Gather and bind the cables with the cable
holder. (Depending on model)
2 Fix the Cable Management firmly to the TV.
(Only LB63**, 39/42/47/50/55/60LB65**-TA/TB,
LB67**, LB69**, LB72**)
Cable Holder
Cable Management
(Only 32LB65**-TA/TB)
Wall Mount Spacer
Cable Management
(Only 70LB65**-TA)
Cable Holder
Cable Management
ENGLISH
ENG
NOTE
28
29
ASSEMBLING AND PREPARING
(Only 32LB65**-TH)
(Only LB87**)
ENGLISH
Cable Holder
Cable Management
Cable Management
(Only 39/42/47/50/55LB65**-TH)
Cable Holder
CAUTION
yy Do not move the TV by holding the cable
holder, as the cable holder may break,
and injuries and damage to the TV may
occur.
Cable Management
(Only LB75**)
Cable Holder
Cable Management
30
ASSEMBLING AND PREPARING
(Only LB87**)
You can make a Skype video call or use the
motion recognition function using the built-in
camera of the TV.
This TV does not support the use of an external
camera.
Preparing Built-in Camera
ENGLISH
ENG
Using Built-in Camera
1 Pull up the slide at the back of the TV.
Angle
Adjustment
Lever
NOTE
7
yy Before using the built-in camera, you
must recognize the fact that you are
legally responsible for the use or misuse
of the camera by the relevant national
laws including the criminal law.
yy The relevant laws include the Personal
Information Protection law which
regulates the processing and transferring
of personal information and the law which
regulates the monitoring by camera in a
workplace and other places.
yy When using the built-in camera,
avoid questionable, illegal, or immoral
situations. Other than at public places or
events, consent to be photographed may
be required. We suggest avoiding the
following situations:
(1) Using the camera in areas where the
use of camera is generally prohibited
such as restroom, locker room, fitting
room and security area.
(2) Using the camera while causing the
infringement of privacy.
(3) Using the camera while causing the
violation of the relevant regulations or
laws.
Slide
NOTE
yy Remove the protective film before using
the built-in camera.
2 You can adjust the angle of the camera with
the angle adjustment lever on the back of
7
the built-in camera.
<Side View>
7
5
5
Lever
Lens
5
31
ASSEMBLING AND PREPARING
ENGLISH
ENG
3 Push down the built-in camera when you are
not using it.
7
5
5
7
7
5
5
7
Name of Parts of Built-in Camera
Camera Lens
Protective film
Microphones
7
5
5
7
Checking the Camera’s Shooting
Range
1 Press the
(Smarthome) button on the
remote control to display the Launcher
menu.
2 Select CAMERA
and then press the
Wheel(OK) button.
NOTE
yy The optimal distance from the camera
to use the motion recognition function is
between 1.5 m and 4.5 m.
MAKING CONNECTIONS
This section on MAKING CONNECTIONS
mainly uses diagrams for the 42LB67** models.
Connect various external devices to the TV
and switch input modes to select an external
device. For more information of external device’s
connection, refer to the manual provided with
each device.
Available external devices are: HD receivers,
DVD players, VCRs, audio systems, USB
storage devices, PC, gaming devices, and other
external devices.
Antenna connection
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
ANTENNA /
CABLE IN
NOTE
yy The external device connection may differ
from the model.
(LB87** : HDMI/DVI IN1/2/3/4)
yy Connect external devices to the TV
regardless of the order of the TV port.
yy If you record a TV programme on a
DVD recorder or VCR, make sure to
connect the TV signal input cable to the
TV through a DVD recorder or VCR. For
more information of recording, refer to
the manual provided with the connected
device.
yy Refer to the external equipment’s manual
for operating instructions.
yy If you connect a gaming device to the TV,
use the cable supplied with the gaming
device.
yy In PC mode, there may be noise
associated with the resolution, vertical
pattern, contrast or brightness. If noise is
present, change the PC output to another
resolution, change the refresh rate to
another rate or adjust the brightness and
contrast on the PICTURE menu until the
picture is clear.
yy In PC mode, some resolution settings
may not work properly depending on the
graphics card.
(*Not Provided)
NOTE
yy Use a signal splitter to use more than 2
TVs.
yy If the image quality is poor, install a signal
amplifier properly to improve the image
quality.
yy If the image quality is poor with an
antenna connected, try to realign the
antenna in the correct direction.
yy An antenna cable and converter are not
supplied.
yy Supported DTV Audio: MPEG, Dolby
Digital, Dolby Digital Plus, HE-AAC.
ENGLISH
ENG
MAKING CONNECTIONS
32
33
MAKING CONNECTIONS
ENGLISH
ENG
Satellite dish connection
Headphone connection
(Only satellite models)
Transmits the headphone signal from the TV to
an external device. Connect the external device
and the TV with the headphone as shown.
Connect the TV to a satellite dish to a satellite
socket with a satellite RF cable (75 Ω).
13/18V
700mA Max
LNB
Satellite IN
(*Not Provided)
(*Not Provided)
NOTE
yyAUDIO menu items are disabled when
connecting a headphone.
yyOptical Digital Audio Out is not available
when connecting a headphone.
yyHeadphone impedance: 16 Ω
yyMax audio output of headphone: 0.624
mW to 1.04 mW
yyHeadphone jack size: 0.35 cm
MAKING CONNECTIONS
(Only LB87**)
ENGLISH
ENG
HDMI connection
Transmits the digital video and audio signals
from an external device to the TV. Connect the
external device and the TV with the HDMI cable
as shown.
Choose any HDMI input port to connect. It does
not matter which port you use.
ARC (Audio Return Channel)
yyAn external audio device that supports
SIMPLINK and ARC must be connected
using HDMI IN 1 (ARC) or HDMI/DVI IN 1
(ARC) port.
yyWhen connected with a high-speed
HDMI cable, the external audio device
that supports ARC outputs optical SPDIF
without additional optical audio cable and
supports the SIMPLINK function.
DVD / Blu-Ray /
HD Cable Box /
HD STB / PC
(Only LB63**, LB65**, LB67**, LB69**, LB72**,
LB75**)
(*Not
Provided)
DVD / Blu-Ray / HD Cable
Box / HD STB / PC
HDMI
NOTE
(*Not Provided)
HDMI
34
yy It is recommended to use the TV with
the HDMI connection for the best image
quality.
yy Use the latest High Speed HDMI™ Cable
with CEC (Customer Electronics Control)
function.
yy High Speed HDMI™ Cables are tested
to carry an HD signal up to 1080p and
higher.
yy Supported HDMI Audio format : Dolby
Digital, DTS, PCM (Up to 192 KHz,
32 KHz/44.1 KHz/48 KHz/88 KHz/96
KHz/176 KHz/192 KHz).
35
MAKING CONNECTIONS
(Only LB87**)
ENGLISH
DVI to HDMI connection
Transmits the digital video signal from an
external device to the TV. Connect the external
device and the TV with the DVI-HDMI cable as
shown. To transmit an audio signal, connect an
audio cable.
Choose any HDMI input port to connect. It does
not matter which port you use.
(Only LB63**, LB65**, LB67**, LB69**, LB72**,
LB75**)
YELLOW
RED
WHITE
(*Not Provided)
(*Not Provided)
AUDIO OUT
DVI OUT
DVD / Blu-Ray / HD Cable Box / PC / HD STB
NOTE
DVD / Blu-Ray / HD Cable Box / PC / HD STB
yy Depending on the graphics card, DOS
mode may not work if a HDMI to DVI
Cable is in use.
yy When using the HDMI/DVI cable, Single
link is only supported.
36
MAKING CONNECTIONS
(Only LB87**)
ENGLISH
ENG
Component connection
Transmits analog video and audio signals
from an external device to the TV. Connect the
external device and the TV with a component
cable as shown.
(Only LB63**, LB65**, LB67**, LB69**, LB72**,
LB75**)
IN
AV
VIDEO
Y
RED
BLUE
GREEN
RED
BLUE
GREEN
RED
BLUE
GREEN
WHITE
RED
RED
RED
RED
WHITE
(*Not Provided)
DVD / Blu-Ray /
HD Cable Box
WHITE
VIDEO
PB
RED
WHITE
RED
GREEN
L
PR
GREEN
(Use the
component gender
cable provided.)
WHITE
RED
BLUE
YELLOW
(Use the composite
gender cable provided.)
YELLOW
BLUE
GREEN
(*Not Provided)
COMPONENT
AUDIO
R
AUDIO
L
R
AUDIO
VIDEO
NOTE
DVD / Blu-Ray / HD Cable Box
yy If cables are not installed correctly, it
could cause this image to display in black
and white or with distorted colours.
37
MAKING CONNECTIONS
ENGLISH
ENG
Composite connection
(Only LB87**)
Transmits analog video and audio signals
from an external device to the TV. Connect the
external device and the TV with the composite
cable as shown.
(Only LB63**, LB65**, LB67**, LB69**, LB72**,
LB75**)
AV
VIDEO
COMPONENT
COMPONENT
AUDIO
PR
PB
PB
Y
RED
WHITE
RED
WHITE
RED
RED
WHITE
YELLOW
WHITE
YELLOW YELLOW
RED
WHITE
YELLOW
YELLOW
(Use the composite
gender cable provided.)
(*Not Provided)
(*Not Provided)
YELLOW
VIDEO
IN
L (MONO) AUDIO R
VIDEO
DVD / Blu-Ray / HD Cable Box / VCR
VCR / DVD / Blu-Ray /
HD Cable Box
L (MONO) AUDIO R
Y
MAKING CONNECTIONS
38
USB connection
You may use an optional external audio system
instead of the built-in speaker.
Connect a USB storage device such as a USB
flash memory, external hard drive, or a USB
memory card reader to the TV and access the
SmartShare menu to use various multimedia
files.
Digital optical audio connection
(USB 3.0 IN)
Transmits a digital audio signal from the TV to an
external device. Connect the external device and
the TV with the optical audio cable as shown.
(*Not Provided)
HUB
(*Not Provided)
HDD
(*Not Provided)
USB
(*Not Provided)
NOTE
OPTICAL AUDIO IN
Digital Audio System
NOTE
yy Do not look into the optical output port.
Looking at the laser beam may damage
your vision.
yy Audio with ACP (Audio Copy Protection)
function may block digital audio output.
yy Some USB Hubs may not work. If a USB
device connected using a USB Hub is not
detected, connect it to the USB port on
the TV directly.
yy Connect the external power source if your
USB is needed.
ENGLISH
ENG
Audio connection
39
MAKING CONNECTIONS
(Only satellite models)
Transmits the video and audio signals from an
external device to the TV set. Connect the external device and the TV set with the euro scart
cable as shown.
NOTE
yy Any Euro scart cable used must be signal
shielded.
yy When watching digital TV in 3D imaging
mode, only 2D out signals can be output
through the SCART cable. (Only 3D
models)
yy If you set the 3D mode to On while a
scheduled recording is performed on
digital TV, monitor out signals cannot be
output through the SCART cable, and the
recording cannot be performed. (Only 3D
models)
y Only for European models
AV1
IN/OUT
ENGLISH
ENG
Euro Scart connection
(*Not Provided)
Output
Type
Current
input mode
Digital TV
AV1
(TV Out1)
Digital TV
Analogue TV, AV
Component
Analogue TV
HDMI
1 TV Out : Outputs Analogue TV or Digital TV
signals.
MAKING CONNECTIONS
Mobile High-definition Link (MHL) is an interface
for transmitting digital audiovisual signals from
mobile phones to television sets.
MHL passive cable
(*Not Provided)
Mobile phone
NOTE
yyConnect the mobile phone to the HDMI
IN 3 (MHL) or HDMI/DVI IN 4 (MHL) port
to view the phone screen on the TV.
yyThe MHL passive cable is needed to
connect the TV and a mobile phone.
yyThis only works for the MHL-enabled
phone.
yySome applications can be operated by
the remote control.
yyFor some mobile phones supporting
MHL, you can control with the Magic
Remote.
yyRemove the MHL passive cable from the
TV when:
»» the MHL function is disabled
»» your mobile device is fully charged in
standby mode
y Different type of MHL cable may be required
depending upon mobile specifications.
ENGLISH
ENG
MHL connection
40
41
REMOTE CONTROL
ENGLISH
ENG
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly. To replace batteries,
open the battery cover, replace batteries (1.5 V AAA) matching the
and
ends to the label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
CAUTION
yyDo not mix old and new batteries, as this may damage the remote control.
yyIn Analogue TV and some countries, some remote control buttons may not work.
yyThe remote control will not be included for all sales market.
Make sure to point the remote control toward the remote control sensor on the TV.
(Depending on model)
(POWER) Turns the TV on or off.
INPUT Changes the input source.
SETTINGS Accesses the main menus.
1 INFO
Views the information of the current programme and screen.
(Depending on model)
1
RATIO Resizes an image. (Depending on model)
Q. MENU Accesses the quick menus.
(User Guide) Sees user- guide.
INPUT Q.MENU
1
SETTINGS
1
2
3
4
5
6
7
8
9
GUIDE
0
Q.VIEW
Number buttons Enters numbers.
GUIDE Shows programme guide.
Q.VIEW Returns to the previously viewed programme.
FAV
P
A
G
E
2
MUTE
RECENT Shows the previous history.
SMART Accesses the Smart Home menus.
MY APPS Shows the list of Apps.
Navigation buttons (up/down/left/right) Scrolls through menus or options.
OK
Selects menus or options and confirms your input.
BACK Returns to the previous level.
LIVE MENU Shows the list of Recommended, Programme, Search and Recorded.
EXIT Clears on-screen displays and returns to TV viewing.
RECENT
OK
BACK
3
TEXT
LIVE MENU
EXIT
T.OPT
SLEEP
AD/
TV/RAD
LIVE TV
REC
SUBTITLE
Adjusts the volume level.
FAV Accesses your favourite programme list.
2
Used for viewing 3D video. (Depending on model)
2 INFO
Views the information of the current programme and screen.
(Depending on model)
MUTE
Mutes all sounds.
ꕌPꕍ Scrolls through the saved programmes.
PAGE
Moves to the previous or next screen.
Coloured buttons These access special functions in some menus.
(
: Red,
: Green,
: Yellow,
: Blue)
3 Teletext buttons These buttons are used for teletext.
SLEEP Sets the sleep timer.
LIVE TV Returns to LIVE TV.
) Controls the Premium contents, Time Machine or
Control buttons (
SmartShare menus or the SIMPLINK compatible devices (USB or SIMPLINK or Time Machine).
REC
Starts to record and displays record menu. (Only Time Machine supported model)
SUBTITLE Recalls your preferred subtitle in digital mode.
AD/ By pressing the AD button, audio descriptions function will be enabled.
(Depending on model)
TV/RAD Selects Radio, TV and DTV programme.
MAGIC REMOTE FUNCTIONS
42
When the message “Magic Remote battery is low. Change the battery.” is
displayed, replace the battery. To replace batteries, open the battery cover, replace
batteries (1.5 V AA) matching
and
ends to the label inside the compartment,
and close the battery cover. Be sure to point the remote control toward the remote
control sensor on the TV. To remove the batteries, perform the installation actions
in reverse.
CAUTION
yy Do not mix old and new batteries, as this may damage the remote control.
yy In Analogue TV and some countries, some remote control buttons may not work.
(Only LB63**, LB65**, LB67**, LB69**, LB72**, LB75**, LB87**)
(POWER)
Turns the TV on or off.
Navigation buttons
(up/down/left/right)
Press the up, down, left or right
button to scroll the menu.If you
press , , or buttons
while the pointer is in use, the
pointer will disappear from the
screen and Magic Remote will
operate like a general remote
control. To display the pointer
on the screen again, shake
Magic Remote to the left and
right.
Wheel(OK)
Press the center of the Wheel
button to select a menu. You
can change programmes and
scroll the menu by using the
Wheel button.
Coloured buttons
These access special functions
in some menus.
: Red,
: Green,
(
: Yellow,
: Blue)
Adjusts the volume level.
(BACK)
Returns to the previous level.
(Smarthome)
Accesses the Smarthome menu.
(EXIT to LIVE)
Switches among broadcast
(antenna) and various inputs.
(Voice recognition)
(Depending on model)
P
Scrolls through the saved
programmes.
/ INPUT
Displays the Screen Remote.
*Accesses the Universal Control
Menu. (Depending on model)
*Pressing and holding the
/ INPUT button will display
a menu to select an external
device that is connected to the
TV.
Used for viewing 3D video.
(Only 3D models)
(MUTE)
Mutes all sounds.
*By Pressing and holding the
button, audio descriptions
function will be enabled.
(Depending on model)
ENGLISH
ENG
Magic Remote Functions
43
MAGIC REMOTE FUNCTIONS
ENGLISH
ENG
Voice recognition (Depending on model)
Network connection is required to use the
voice recognition function.
1 Press the Voice recognition button.
2 Speak when the voice display window
appears on the left of the TV screen.
• The voice recognition may fail when you
speak too fast or too slow.
• Use the Magic Remote no further than
10 cm from your face.
• The recognition rate may vary
depending on the user’s characteristics
(voice, pronunciation, intonation and
speed) and the environment (noise and
TV volume).
Registering Magic Remote
How to HOME
register the Magic Remote
BACK
To use the Magic Remote, first pair
it with your TV.
P
MY APPS
1 Put batteries into the Magic
Remote and turn the TV on.
2 Point the Magic Remote at your
TV and press the Wheel(OK) on
the remote control.
»»If the TV fails to register the
Magic Remote, try again after
turning the TV off and back
on.
How to deregister the Magic Remote
(BACK)
(Smart
home)
Press the (BACK) and
(Smarthome) buttons at the
same time, for five seconds, to
unpair the Magic Remote with
your TV.
»»Pressing and holding the
(EXIT to LIVE) button will let
you cancel and re-register
Magic Remote at once.
How to use Magic Remote
yy Shake the Magic Remote
slightly to the right and left
or press (Smarthome),
/ INPUT,
buttons
to make the pointer appear
on the screen.
»»The pointer will appear
when you turn the Wheel
button. (Depending on
model)
yy If the pointer has not been
used for a certain period
of time or Magic Remote is
placed on a flat surface, then
the pointer will disappear.
yy If the pointer is not
responding smoothly, you
can reset the pointer by
moving it to the edge of the
screen.
yy The Magic Remote depletes
batteries faster than a
normal remote due to the
additional features.
MAGIC REMOTE FUNCTIONS / USING THE USER GUIDE
y Take care not to bump into nearby furniture
or other people when using the Magic
Remote.
y Manufacturer and installer cannot provide
service related to human safety as the
applicable wireless device has possibility of
electric wave interference.
User Guide allows you to more easily access the
detailed TV information.
(Smarthome) button to access
1 Press the
the Smarthome menu.
2 Select User Guide and press Wheel(OK).

yyUse the remote control within the
specified range (within 10 m). You may
experience communication failures when
using the device outside the coverage
area or if there are obstacles within the
coverage area.
yyYou may experience communication
failures depending on the accessories.
Devices such as a microwave oven
and wireless LAN operate in the same
frequency band (2.4 GHz) as the Magic
Remote. This may cause communication
failures.
yyThe Magic Remote may not work properly
if a wireless router (AP) is within 1 meter
of the TV. Your wireless router should be
more than 1 m away from the TV.
yyDo not disassemble or heat the battery.
yyDo not drop the battery. Avoid avoid
extreme shocks to the battery.
yyInserting the battery the wrong way may
result in explosion.
Using the User guide
NOTE
yy You can also access the User Guide by
pressing (User Guide) in the remote
control. (Depending on model)
ENGLISH
ENG
Precautions to Take when Using
the Magic Remote
44
45
MAINTENANCE / TROUBLESHOOTING
ENGLISH
ENG
MAINTENANCE
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
yy Make sure to turn the power off and disconnect the power cord and all other cables first.
yy When the TV is left unattended and unused for a long time, disconnect the power cord from the
wall outlet to prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted
mild detergent. Then wipe immediately with a dry cloth.
CAUTION
yy Avoid touching the screen at all times, as this may result in damage to the screen.
yy Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may
result in scratches and image distortions.
yy Do not use any chemicals as this may damage the product.
yy Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
Problem
Solution
Cannot control the
TV with the remote
control.
yy Check the remote control sensor on the product and try again.
yy Check if there is any obstacle between the product and the remote control.
to ).
yy Check if the batteries are still working and properly installed ( to ,
No image display
and no sound is
produced.
yy Check if the product is turned on.
yy Check if the power cord is connected to a wall outlet.
yy Check if there is a problem in the wall outlet by connecting other products.
The TV turns off
suddenly.
yy Check the power control settings. The power supply may be interrupted.
yy Check if the Sleep Timer or Timer Power Off feature is activated in the
Timers settings.
yy If there is no signal while the TV is on, the TV will turn off automatically
after 15 minutes of inactivity.
When connecting to yy Turn the TV off/on using the remote control.
the PC (HDMI/DVI), yy Reconnect the HDMI cable.
‘No signal’ or ‘Invalid yy Restart the PC with the TV on.
Format’ is displayed.
TROUBLESHOOTING
46
Problem
No sound is produced while
images are displaying.
One of the speakers produce
noises or does not produce
sound.
Solution
Press
+ or - button.
yy
Check if the sound is muted by pressing MUTE.
yy
Scroll to other channels. There may a problem with the broadcast.
yy
Check if the audio cables are connected properly.
yy
A change in ambient humidity or temperature may result in an unusual
yy
noise when the product turns on or off.
There is no problem with your product.
yy
Video
Solution
Problem
An image displays in black
Adjust the colour setting in the PICTURE menu.
yy
and white or the colour quality yy
Keep a sufficient distance between this product and other electronic
is poor.
products.
Scroll to other channels. There may a problem with the broadcast.
yy
Horizontal or vertical bars
appears or images blur
Lines or streaks appear on
images
Afterimages (ghosts) appear
when the product turns off
Check if there are local interferences such as an electrical appliance
yy
or power tool.
Check the antenna or aim the antenna to the proper direction.
yy
Pixels may have been damaged from a fixed image displayed for
yy
a long time (image burn). Use a screen saver to prevent the pixel
damage on the screen.
The power is on but the screen yy
Adjust the brightness and contrast in the PICTURE menu.
appears extremely dark.
“No Signal” appears on the
screen.
Thin lines appear in the
background of the screen.
The reception on some
channels is poor
Check if the signal cable is connected between the TV and products
yy
properly.
Check the selected input source by pressing INPUT.
yy
Check the video cable connections.
yy
Scroll to other channels. There may a problem with the broadcast.
yy
The station signal may be weak. Aim the antenna to the proper
yy
direction.
Check if there is local interference such as an electrical appliance or
yy
power tool.
ENGLISH
ENG
Audio
47
SPECIFICATIONS
ENGLISH
ENG
SPECIFICATIONS
Wireless module(LGSBW41) Specifications
Wireless LAN
Bluetooth
Standard
IEEE 802.11a/b/g/n
Standard
Bluetooth Version 3.0
Frequency
ragne
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz (for Non EU)
Frequency
ragne
2400 to 2483.5 MHz
Output power
(Max.)
802.11a: 13 dBm
802.11b: 15 dBm
802.11g: 14 dBm
802.11n - 2.4GHz: 16 dBm
802.11n - 5GHz: 16 dBm
Output power
(Max.)
10 dBm or Lower
yyBecause band channel used by the country could be different, the user can not change or adjust
the operating frequency and this product is set for the regional frequency table.
yyThis device should be installed and operated with minimum distance 20 cm between the device
and your body. And this phrase is for the general statement for consideration of user environment.
SPECIFICATIONS
48
42LB63**
47LB63**
55LB63**
42LB6310-TC
42LB631T-TC
42LB6330-TD
42LB633T-TD
42LB633Y-TD
47LB6310-TC
47LB631T-TC
47LB6330-TD
47LB633T-TD
47LB633Y-TD
55LB6310-TC
55LB631T-TC
55LB6330-TD
55LB633T-TD
55LB633Y-TD
960 x 610 x 218
1072 x 677 x 247
1241 x 772 x 247
Without stand (mm) 960 x 567 x 54.5
1072 x 629 x 54.5
1241 x 725 x 55.5
MODELS
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
9.9
13.4
18.7
Without stand (kg)
9.6
13.0
18.3
Power requirement
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
32LB65**
32LB6500-TA
32LB650T-TA
32LB650V-TA
32LB6520-TB
32LB652T-TB
32LB652Y-TB
MODELS
32LB6500-TH
32LB650T-TH
731 x 484 x 207
731 x 475 x 207
Without stand (mm) 731 x 437 x 54.5
731 x 437 x 54.5
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
6.5
6.5
Without stand (kg)
6.3
6.3
Power requirement
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
39LB65**
MODELS
39LB6500-TA
39LB650T-TA
39LB650V-TA
39LB6520-TB
39LB652T-TB
39LB652Y-TB
39LB6500-TH
39LB650T-TH
884 x 569 x 218
884 x 570 x 193
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
8.6
8.6
Without stand (kg)
8.3
8.3
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Without stand (mm) 884 x 521 x 54.5
Power requirement
884 x 521 x 54.5
ENGLISH
ENG
Product specifications may be changed without prior notice due to upgrade of product functions.
For the power supply and power consumption, refer to the label attached to the product.
49
SPECIFICATIONS
ENGLISH
ENG
42LB65**
42LB6500-TA
42LB650T-TA
42LB650V-TA
42LB6520-TB
42LB652T-TB
42LB652Y-TB
42LB6500-TH
42LB650T-TH
960 x 610 x 218
960 x 612 x 193
Without stand (mm) 960 x 567 x 54.5
960 x 567 x 54.5
MODELS
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
9.9
9.9
Without stand (kg)
9.6
9.6
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power requirement
47LB65**
47LB6500-TA
47LB650T-TA
47LB650V-TA
47LB6520-TB
47LB652T-TB
47LB652Y-TB
MODELS
47LB6500-TH
47LB650T-TH
1072 x 677 x 247
1072 x 675 x 230
Without stand (mm) 1072 x 629 x 54.5
1072 x 629 x 54.5
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
13.4
13.3
Without stand (kg)
13.0
13.0
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power requirement
50LB65**
50LB6500-TA
50LB650T-TA
50LB650V-TA
50LB6520-TB
50LB652T-TB
50LB652Y-TB
50LB6500-TH
50LB650T-TH
1127 x 710 x 247
1127 x 710 x 230
Without stand (mm) 1127 x 660 x 54.5
1127 x 660 x 54.5
MODELS
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
14.7
14.6
Without stand (kg)
14.3
14.3
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power requirement
SPECIFICATIONS
50
MODELS
55LB6500-TH
55LB650T-TH
1241 x 772 x 247
1241 x 769 x 224
Without stand (mm) 1241 x 725 x 55.5
1241 x 725 x 55.5
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
18.7
18.6
Without stand (kg)
18.3
18.3
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
60LB65**
70LB65**
60LB6500-TA
60LB650T-TA
60LB650V-TA
60LB6520-TB
60LB652T-TB
60LB652Y-TB
70LB6560-TA
70LB656T-TA
70LB656Y-TA
1351 x 834 x 271
1574 x 964 x 344
Without stand (mm) 1351 x 785 x 57.5
1574 x 916 x 60.2
Power requirement
MODELS
ENGLISH
ENG
55LB65**
55LB6500-TA
55LB650T-TA
55LB650V-TA
55LB6520-TB
55LB652T-TB
55LB652Y-TB
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
22.4
31.6
Without stand (kg)
21.8
30.1
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
42LB67**
47LB67**
50LB67**
42LB6700-TA
42LB670T-TA
42LB670Y-TA
47LB6700-TA
47LB670T-TA
47LB670Y-TA
50LB6700-TA
50LB670T-TA
50LB670Y-TA
948.2 x 606.9 x 210.9
1059.9 x 671.9 x 247.5 1116.1 x 704.9 x 247.5
Power requirement
MODELS
Dimensions
(W x H x D)
Weight
With stand (mm)
Without stand (mm) 948.2 x 558.2 x 55.1
1059.9 x 621 x 55.1
1116.1 x 652.9 x 55.1
With stand (kg)
10.1
13.2
14.6
Without stand (kg)
9.7
12.7
14.1
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
Power requirement
51
SPECIFICATIONS
ENGLISH
ENG
MODELS
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
Without stand (kg)
55LB67**
42LB69**
47LB69**
55LB6700-TA
55LB670T-TA
55LB670Y-TA
42LB6900-TA
42LB690T-TA
42LB690Y-TA
42LB692V-TB
47LB6900-TA
47LB690T-TA
47LB690Y-TA
47LB692V-TB
1229.8 x 767.5 x 247.5 949 x 608 x 211
Without stand (mm) 1229.8 x 708.6 x 55.1
Power requirement
MODELS
949 x 560 x 55.1
1061 x 623 x 55.1
18.5
10.3
13.3
18
10
12.8
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
55LB69**
42LB72**
47LB72**
55LB6900-TA
55LB690T-TA
55LB690Y-TA
55LB692V-TB
42LB7200-TA
42LB720T-TA
42LB720Y-TA
47LB7200-TA
47LB720T-TA
47LB720Y-TA
1231 x 769 x 247
949 x 608 x 211
1061 x 670 x 247
949 x 560 x 55.1
1061 x 623 x 55.1
13.3
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
19
10.3
Without stand (kg)
18.5
10
Without stand (mm) 1231 x 718 x 55.1
Power requirement
MODELS
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
Without stand (kg)
12.8
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
55LB72**
60LB72**
65LB72**
55LB7200-TA
55LB720T-TA
55LB720Y-TA
60LB7200-TA
60LB720T-TA
60LB720Y-TA
65LB7200-TA
65LB720T-TA
65LB720Y-TA
1231 x 769 x 247
1338.4 x 834.7 x 288.9 1449.5 x 883.7 x 313.9
Without stand (mm) 1231 x 718 x 55.1
Power requirement
1061 x 670 x 247
1338.4 x 778.8 x 58.1
1449.5 x 840.8 x 58.1
19
22.2
27.9
18.5
21.3
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
26.5
AC 100-240 V~ 50 / 60 Hz
SPECIFICATIONS
42LB75**
47LB75**
55LB75**
42LB7500-TE
42LB750T-TE
47LB7500-TE
47LB750T-TE
55LB7500-TE
55LB750T-TE
949 x 607.7 x 213.4
1061 x 666 x 227
1231 x 766 x 237
1061 x 623 x 55.1
1231 x 718 x 55.1
13.7
19.6
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
10.7
Without stand (kg)
10
12.8
18.5
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
60LB75**
65LB75**
60LB7500-TE
60LB750T-TE
65LB7500-TE
65LB750T-TE
Without stand (mm) 949 x 560 x 55.1
Power requirement
MODELS
Dimensions
(W x H x D)
Weight
With stand (mm)
Without stand (mm) 1338.4 x 778.8 x 58.1
With stand (kg)
27.9
Without stand (kg)
21.3
26.5
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
49LB87**
55LB87**
60LB87**
49LB870T-TA
49LB870Y-TA
55LB870T-TA
55LB870Y-TA
60LB870T-TA
60LB870Y-TA
1091 x 690 x 229
1227 x 769 x 229
1335 x 830 x 261
Without stand (mm) 1091 x 632 x 34.7
1227 x 709 x 34.7
1335 x 770 x 35.7
With sound bar
supporter (mm)
1091 x 688 x 34.7
1227 x 765 x 34.7
1335 x 826 x 35.7
With stand (kg)
17.4
22.6
27.1
Without stand (kg)
16.7
21.9
26.2
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
MODELS
Weight
1449.5 x 840.8 x 58.1
22.6
Power requirement
Dimensions
(W x H x D)
1338.4 x 826.2 x 268.4 1449.5 x 894.4 x 293.1
With stand (mm)
Power requirement
ENGLISH
ENG
MODELS
52
53
SPECIFICATIONS
ENGLISH
ENG
CI Module Size (W x H x D)
Environment condition
100.0 mm x 55.0 mm x 5.0 mm
Operating Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Digital TV
(Depending on Country)
Analogue TV
(Depending on Country)
Television System
DVB-T
DVB-T/T21
DVB-T/T2/C/S/S22
PAL B/B, PAL B/G, PAL D/K, PAL-I
SECAM B/G, SECAM D/K
NTSC-M
Programme Coverage
VHF, UHF
C-Band2, Ku-Band2
VHF, UHF, CATV
External Antenna Impedance
1 Only DVB-T2 support models.
2 Only DVB-T2/C/S2 support models.
75 Ω
Record the model number and serial
number of the TV.
Refer to the label on the back cover and
quote this information to your dealer
when requiring any service.
MODEL
SERIAL
(Only DTV)
Download PDF

advertising