LG | 50PN6500 | LG 42PN4500 Owner’s Manual

OWNER’S MANUAL
PLASMA TV
Please read this manual carefully before operating
your set and retain it for future reference.
PN45**
PN65**
P/NO : MFL67648602 (1212-REV00)
www.lg.com
2
TABLE OF CONTENTS
ENGLISH
ENG
TABLE OF CONTENTS
3
SAFETy INSTRUCTIONS
34
LICENSES
8
INSTALLATION PROCEdURE
34
OPEN SOURCE SOFTWARE NOTICE
8
ASSEMBLING ANd PREPARING
34
8
12
13
14
15
15
17
18
19
Unpacking
Separate purchase
Parts and buttons
Lifting and moving the TV
Setting up the TV
- Attaching the stand
Mounting on a table
Mounting on a wall
Tidying cables
ExTERNAL CONTROL dEvICE
SETUP
20
MAKING CONNECTIONS
20
21
21
22
22
22
23
24
Antenna Connection
HDMI Connection
DVI to HDMI connection
Component Connection
Audio Connection
- Digital optical audio connection
Composite Connection
USB Connection
25
REMOTE CONTROL
27
USING THE USER GUIdE
28
MAINTENANCE
28
28
28
Cleaning your TV
- Screen, frame, cabinet and stand
- Power cord
28
TROUBLESHOOTING
30
ENvIRONMENTAL INFORMATION
31
SPECIFICATIONS
WARNING
y If you ignore the warning message, you may
be seriously injured or there is a possibility of
accident or death.
CAUTION
y If you ignore the caution message, you may be
slightly injured or the product may be damaged.
NOTE
y The note helps you understand and use the
product safely. Please read the note carefully
before using the product.
SAFETY INSTRUCTIONS
ENGLISH
ENG
SAFETy INSTRUCTIONS
Please read these safety precautions carefully before using the product.
WARNING
y Do not place the TV and
remote control in the following
environments:
- A location exposed to
direct sunlight
- An area with high humidity
such as a bathroom
- Near any heat source
such as stoves and other
devices that produce heat
- Near kitchen counters or
humidifiers where they can
easily be exposed to steam
or oil
- An area exposed to rain or
wind
- Near containers of water
such as vases
Otherwise, this may result in
fire, electric shock, malfunction
or product deformation.
y Do not place the product
where it might be exposed to
dust.
This may cause a fire hazard.
y Mains plug is the
disconnecting device. The
plug must remain readily
operable.
y Do not touch the power plug
with wet hands. Additionally, if
the cord pin is wet or covered
with dust, dry the power plug
completely or wipe dust off.
You may be electrocuted due
to excess moisture.
y Make sure to connect the
power cable to the grounded
current. (Except for devices
which are not grounded.)
You may be electrocuted or
injured.
3
y Insert the power cable
completely into wall socket.
If the power cable is not
inserted completely into wall
socket, a fire could break out.
y Ensure the power cord does
not come into contact with
hot objects such as a heater.
This may cause a fire or an
electric shock hazard.
y Do not place a heavy object,
or the product itself, on power
cables.
Otherwise, this may result in
fire or electric shock.
y Bend antenna cable between
inside and outside building to
prevent rain from flowing in.
This may cause water
damaged inside the Product
and could give an electric
shock.
y When mounting a TV on the
wall, make sure not to install
TV by hanging power and
signal cables on the back of
the TV.
It may cause fire, electric
shock.
y Do not plug too many
electrical devices into a single
multiple electrical outlet.
Otherwise, this may result in
fire due to over-heating.
y Do not drop the product or let
it fall over when connecting
external devices.
Otherwise, this may result
in injury or damage to the
product.
4
SAFETY INSTRUCTIONS
ENGLISH
ENG
yyKeep the packing antimoisture material or vinyl
packing out of the reach of
children.
Anti-moisture material is
harmful if swallowed. If
swallowed by mistake, force
the patient to vomit and
visit the nearest hospital.
Additionally, vinyl packing can
cause suffocation. Keep it out
of the reach of children.
yyDo not let your children climb
or cling onto the TV.
Otherwise, the TV may
fall over, which may cause
serious injury.
yyDispose of used batteries
carefully to protect a child
from eating them.
Please seek Doctor- Medical
Attention immediately if child
consumes batteries.
yyDo not insert any metal
objects/conductors (like
a metal chopstick/cutlery/
screwdriver) between power
cable plug and input Wall
Socket while it is connected
to the input terminal on the
wall. Additionally, do not
touch the power cable right
after plugging into the wall
input terminal.
You may be electrocuted.
(Depending on model)
yyDo not put or store
inflammable substances
near the product. There is
a danger of combustion/
explosion or fire due to
careless handling of the
inflammable substances.
yyDo not drop metallic objects
such as coins, hair pins,
chopsticks or wire into the
product, or inflammable
objects such as paper and
matches. Children must pay
particular attention.
Electrical shock, fire or injury
can occur. If a foreign object
is dropped into the product,
unplug the power cord and
contact the service centre.
yyDo not spray water on the
product or scrub with an
inflammable substance
(thinner or benzene). Fire or
electric shock accident can
occur.
yyDo not allow any impact,
shock or any objects to fall
into the unit, and do not drop
anything onto the screen.
You may be injured or the
product can be damaged.
yyNever touch this product or
antenna during a thunder or
lighting storm.
You may be electrocuted.
yyNever touch the wall outlet
when there is leakage of
gas, open the windows and
ventilate.
It may cause a fire or a burn
by a spark.
yyDo not disassemble, repair
or modify the product at your
own discretion.
Fire or electric shock accident
can occur.
Contact the service centre for
check, calibration or repair.
yyIf any of the following
occur, unplug the product
immediately and contact your
local service centre.
--The product has been
impacted by shock
--The product has been
damaged
--Foreign objects have
entered the product
--The product produced
smoke or a strange smell
This may result in fire or
electric shock.
SAFETY INSTRUCTIONS
yyApparatus shall not be
exposed to dripping or
splashing and no objects
filled with liquids, such as
vases, shall be placed on the
apparatus.
yyWhen installing the antenna,
consult with a qualified
service technician. If not
installed by a qualified
technician.
This may create a fire hazard
or an electric shock hazard.
yyWe recommend that you
maintain a distance of at least
2 to 7 times the diagonal
screen size when watching
TV.
If you watch TV for a long
period of time, this may
cause blurred vision.
yyOnly use the specified type of
battery.
This could cause damage to
the remote control.
CAUTION
yyInstall the product where no
radio wave occurs.
yyThere should be enough
distance between an outside
antenna and power lines
to keep the former from
touching the latter even when
the antenna falls.
This may cause an electric
shock.
yyDo not install the product
on places such as unstable
shelves or inclined surfaces.
Also avoid places where
there is vibration or where
the product cannot be fully
supported.
Otherwise, the product may
fall or flip over, which may
cause injury or damage to the
product.
yyIf you install the TV on a
stand, you need to take
actions to prevent the product
from overturning. Otherwise,
the product may fall over,
which may cause injury.
yyIf you intend to mount the product to a wall, attach
VESA standard mounting interface (optional parts)
to the back of the product. When you install the set
to use the wall mounting bracket (optional parts),
fix it carefully so as not to drop.
yyOnly use the attachments / accessories specified
by the manufacturer.
yyDo not mix new batteries with
old batteries.
This may cause the batteries
to overheat and leak.
yyMake sure there are no
objects between the remote
control and its sensor.
yySignal from the remote
control may be disturbed by
sun light or other strong light.
In this case, darken the room.
yyWhen connecting external
devices such as video game
consoles, make sure the
connecting cables are long
enough.
Otherwise, the product may
fall over, which may cause
injury or damage the product.
yyDo not turn the product
On/Off by plugging-in or
unplugging the power plug to
the wall outlet. (Do not use
the power plug for switch.)
It may cause mechanical
failure or could give an
electric shock.
ENGLISH
ENG
yyIf you don’t intend to use
the product for a long time,
unplug the power cable from
the product.
Covering dust can cause a
fire, or insulation deterioration
can cause electric leakage,
electric shock or fire.
5
6
SAFETY INSTRUCTIONS
ENGLISH
ENG
yyPlease follow the installation
instructions below to prevent
the product from overheating.
--The distance between the
product and the wall should
be more than 10 cm.
--Do not install the product in
a place with no ventilation
(e.g., on a bookshelf or in
a cupboard).
--Do not install the product
on a carpet or cushion.
--Make sure the air vent is
not blocked by a tablecloth
or curtain.
Otherwise, this may result in
fire.
yyTake care not to touch the
ventilation openings when
watching the TV for long
periods as the ventilation
openings may become hot.
This does not affect the
operation or performance of
the product.
yyPeriodically examine the cord of your appliance,
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized servicer.
yyPrevent dust collecting on the
power plug pins or outlet.
This may cause a fire hazard.
yyProtect the power cord from
physical or mechanical
abuse, such as being twisted,
kinked, pinched, closed in a
door, or walked upon. Pay
particular attention to plugs,
wall outlets, and the point
where the cord exits the
appliance.
yyDo not press strongly upon
the panel with a hand or
sharp object such as nail,
pencil or pen, or make a
scratch on it.
yyAvoid touching the screen or
holding your finger(s) against
it for long periods of time.
Doing so may produce some
temporary distortion effects
on the screen.
yyWhen cleaning the product
and its components, unplug
the power first and wipe it
with a soft cloth. Applying
excessive force may cause
scratches or discolouration.
Do not spray with water or
wipe with a wet cloth. Never
use glass cleaner, car or
industrial shiner, abrasives
or wax, benzene, alcohol
etc., which can damage the
product and its panel.
Otherwise, this may result in
fire, electric shock or product
damage (deformation,
corrosion or breakage).
yyAs long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.
yyWhen unplugging the cable,
grab the plug and unplug it,
by pulling at the plug. Don’t
pull at the cord to unplug the
power cord from the power
board. As this could be
hazards.
yyWhen moving the product,
make sure you turn the power
off first. Then, unplug the
power cables, antenna cables
and all connecting cables.
The TV set or power cord
may be damaged, which may
create a fire hazard or cause
electric shock.
yyWhen moving or unpacking
the product, work in pairs
because the product is heavy.
Otherwise, this may result in
injury.
SAFETY INSTRUCTIONS
yyRefer all servicing to
qualified service personnel.
Servicing is required when
the apparatus has been
damaged in any way, such
as power supply cord or
plug is damaged, liquid has
been spilled or objects have
fallen into the apparatus, the
apparatus has been exposed
to rain or moisture, does not
operate normally, or has been
dropped.
yyIf the product feels cold to the
touch, there may be a small
“flicker” when it is turned
on. This is normal, there is
nothing wrong with product.
yyThe panel is a high
technology display product
with resolution of two million
to six million pixels. You
may see tiny black dots and/
or brightly coloured dots
(red, blue or green) at a
size of 1 ppm on the panel.
This does not indicate a
malfunction and does not
affect the performance and
reliability of the product.
This phenomenon also occurs
in third-party products and is
not subject to exchange or
refund.
yyYou may find different
brightness and colour of the
panel depending on your
viewing position(left/right/top/
down).
This phenomenon occurs due
to the characteristic of the
panel. It is not related with
the product performance, and
it is not malfunction.
ENGLISH
ENG
yyContact the service centre
once a year to clean the
internal parts of the product.
Accumulated dust can cause
mechanical failure.
7
yyDisplaying a still image (e.g., broadcasting
channel logo, on-screen menu, scene from a
video game) for a prolonged time may cause
damage to the screen, resulting in retention of
the image, which is known as image sticking. The
warranty does not cover the product for image
sticking.
Avoid displaying a fixed image on your
television’s screen for a prolonged period (2
or more hours for LCD, 1 or more hours for
Plasma).
Also, if you watch the TV at a ratio of 4:3 for
a long time, image sticking may occur on the
borders of the panel.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
yyGenerated Sound
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated
by plastic thermal contraction due to temperature and humidity. This noise is common for
products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A
low level noise is generated from a high-speed
switching circuit, which supplies a large amount
of current to operate a product. It varies depending on the product.
This generated sound does not affect the
performance and reliability of the product.
8
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
ENGLISH
ENG
NOTE
yy
yy
yy
yy
yy
Image shown may differ from your TV.
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
The available menus and options may differ from the input source or product model that you are using.
New features may be added to this TV in the future.
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned
off if it will not be watched for some time, as this will reduce energy consumption.
yy The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced,
and this will reduce the overall running cost.
Installation Procedure
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you
purchased your product. The illustrations in this manual may differ from the actual product and item.
CAUTION
yy Do not use any unapproved items to ensure the safety and product life span.
yy Any damag or injuries caused by using unapproved items are not covered by the manufacturer’s warranty.
yy Some models have a thin film attached on to the screen and this must not be removed.
Remote control, batteries (AAA)
(See p. 25, 26)
Owner’s manual
Ferrite core
(Depending on model)
(See p. 10)
Desk-mount Screw
(Only 42PN45**)
(See p. 17)
ASSEMBLING AND PREPARING
9
ENGLISH
ENG
Power Cord Holder
(See p. 19)
Power Cord
(Depending on model)
Screw for assembly
7 EA, M4 x 14
(Only 42PN45**)
(See p. 15)
or
Stand Body / Stand
Base
(See p. 15)
Isolator
(Depending on model)
(See p. 11)
Protection Cover
(Only 50PN45**,50PN65**)
(See p. 16)
Screw for assembly
7 EA, M5 x 16
(Only 50PN45**,
50/60PN65**)
(See p. 15)
10
ASSEMBLING AND PREPARING
ENGLISH
ENG
NOTE
yyThe items supplied with your product may vary depending on the model.
yyProduct specifications or contents of this manual may be changed without prior notice due to upgrade of product
functions.
How to use the ferrite core
1 Use the ferrite core to reduce the electromagnetic interference in the power cable.
Wind the power cable on the ferrite core once. Place the ferrite core close to the TV and a wall plug.
[to the TV]
[to a wall plug]
[Figure 1]
(Black)
[Cross Section of
Ferrite Core]
2 Use the ferrite core to reduce the electromagnetic interference in the component Y, Pb, Pr, L,
R cable & AV cable. Wind the component Y, Pb, Pr, L, R cable & AV cable on the ferrite core once.
Place the ferrite core close to the TV.
[to an External device]
[to the TV]
(Black)
[Cross Section of
Ferrite Core]
10 mm(+ / - 5 mm)
[Figure 2-1]
Wind the PC audio cable on the ferrite core once.
[to the TV]
[to an External device]
10 mm(+ / - 5 mm)
[Figure 2-2]
-If there are two ferrite cores, follow as shown in Figure 1.
-If there are three ferrite cores, follow as shown in Figures 1 and 2.
yyFor an optimal connection, HDMI cables and USB devices
should have bezels less than 10 mm thick and 18 mm width.
Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB port.
*A
*B
10 mm
18 mm
ASSEMBLING AND PREPARING
11
NOTE
-- Use this to install TV in a place where there is a voltage difference between TV Set and GND of antenna signal.
»» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact might be
heated and excessive heat might cause an accident.
-- You can improve the safety when watching TV by efficiently removing power voltage from TV antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall, mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
-- Before starting, be sure that the TV antenna is connected.
1. Connect to TV.
Wall
ANTENNA/
CABLE IN
Cable / Antenna
or
Isolator
2. Connect to Set-Top box.
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains connection or through
other equipment with a connection to protective earthing - and to a cable distribution system using coaxial cable, may
in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided
through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
ENGLISH
ENG
yy Antenna Isolator Installation Guide
12
ASSEMBLING AND PREPARING
ENGLISH
ENG
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
LG Audio Device
Compatibility
LG Audio Device
PN45**
PN65**
•
•
The model name or design may be changed depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
ASSEMBLING AND PREPARING
13
ENGLISH
ENG
Parts and buttons
Screen
LAN
AUDI
Speakers
Buttons
Power indicator
Button
Description
Turns the power on or off.
Selects the highlighted menu option or confirms an input
S
Accesses the main menus, or saves your input and exits the menus.
Changes the input source
H
H
Adjusts the volume level.
Scrolls through the saved programmes.
COMPONENT
IN
AV IN 1
Remote control sensor
AV IN 2
L/MONO
14
ASSEMBLING AND PREPARING
ENGLISH
ENG
Lifting and moving the TV
Please note the following advice to prevent the TV from
being scratched or damaged and for safe transportation
regardless of its type and size.
yy When transporting a large TV, there should be
at least 2 people.
yy When transporting the TV by hand, hold the
TV as shown in the following illustration.
CAUTION
yy Avoid touching the screen at all times, as this may
result in damage to the screen.
yy It is recommended to move the TV in the box
or packing material that the TV originally came
in.
yy Before moving or lifting the TV, disconnect the
power cord and all cables.
yy When holding the TV, the screen should face
away from you to avoid damage.
yy When transporting the TV, do not expose the
TV to jolts or excessive vibration.
yy When transporting the TV, keep the TV upright,
never turn the TV on its side or tilt towards the
left or right.
yy Hold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part,
speaker, or speaker grill area.
Sta
ASSEMBLING AND PREPARING
ENGLISH
ENG
Setting up the TV
Image shown may differ from your TV.
Attaching the stand
1
Only 50PN45**, 50/60PN65**
3
3 EA
M5 x 16
Only 42PN45**
3 EA
M4 x 14
Stand Body
Front
Only 50PN45**,
50/60PN65**
4 EA
M5 x 16
Only 42PN45**
Stand Base
4 EA
M4 x 14
2
15
16
ASSEMBLING AND PREPARING
To detach the stand
ENGLISH
ENG
(Only 50PN45**, 50PN65**)
1
CAUTION
yy When attaching the stand to the TV set, place the
screen facing down on a cushioned table or flat
surface to protect the screen from scratches.
yy Make sure that the screws are inserted correctly
and fastened securely. If they are not fastened
securely enough, the TV may tilt forward after
being installed. Do not use too much force and
over tighten the screws; otherwise screw may be
damaged and not tighten correctly.
NOTE
yy Remove the stand before installing the TV on a
wall mount by performing the stand attachment in
reverse.
yy When installing the wall mounting bracket, use the
Protection cover.
yy This will protect the opening from accumulating dust
and dirt.
4 EA
M5 x 16
2
Protection
cover
2
1 EA
M5 x 16
1
ASSEMBLING AND PREPARING
1 Lift and tilt the TV into its upright position on a table.
-- Leave a 10 cm (minimum) space from the wall
for proper ventilation.
10 cm
10 cm
Adjusting the angle of the TV to suit view
(This feature is not available for all models.)
Adjusting the angle of the TV to suit view
Swivel 20 degrees to the left or right and adjust the angle
of the TV to suit your view.
20˚
20˚
m
10 c
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
yy Do not place the TV near or on sources of heat,
as this may result in fire or other damage.
Securing the TV to a table
Fix the TV to a table to prevent from tilting forward,
damage, and potential injury.
Mount the TV on a table, and then insert and tighten the
supplied screw on the rear of the stand.
(Only 42PN45**)
WARNING
yy To prevent TV from falling over, the TV should be
securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the TV
may cause injury.
CAUTION
yy When adjusting the angle of the product, watch
out for your fingers.
-- Personal injury may occur if hands or fingers are
pinched. If the product is tilted too much, it may
fall, causing damage or injury.
ENGLISH
ENG
Mounting on a table
17
18
ASSEMBLING AND PREPARING
ENGLISH
ENG
Securing the TV to a wall
(This feature is not available for all models.)
1 Insert and tighten the eye-bolts, or TV brackets and
bolts on the back of the TV.
-- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eyebolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly with a
sturdy rope.
Make sure to keep the rope horizontal with the flat
surface.
CAUTION
yy Make sure that children do not climb on or hang
on the TV.
WARNING
yyIf a television is not positioned in a sufficiently
stable location, it can be potentially hazardous due
to falling. Many injuries, particularly to children, can
be avoided by taking simple precautions such as:
»» Using cabinets or stands recommended by the
manufacturer of the television.
»» Only using furniture that can safely support the
television.
»» Ensuring the television is not overhanging the
edge of the supporting furniture.
»» Not placing the television on tall furniture (for
example, cupboards or bookcases) without
anchoring both the furniture and the television to
a suitable support.
»» Not standing the televisions on cloth or other
materials placed between the television and
supporting furniture.
»» Educating children about the dangers of climbing
on furniture to reach the television or its controls.
Mounting on a wall
Attach an optional wall mount bracket at the rear of the
TV carefully and install the wall mount bracket on a solid
wall perpendicular to the floor. When you attach the
TV to other building materials, please contact qualified
personnel.
LG recommends that wall mounting be performed by a
qualified professional installer.
NOTE
yy Use a platform or cabinet that is strong and large
enough to support the TV securely.
yy Brackets, bolts and ropes are not provided. You
can obtain additional accessories from your local
dealer.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount bracket that
meet the VESA standard. Standard dimensions for the
wall mount kits are described in the following table.
ASSEMBLING AND PREPARING
42/50PN45**
50/60PN65**
Model
vESA (A x B)
Tidying cables
1
400 x 400
Standard screw
Install the Power Cord Holder and Power Cord. It
will help prevent the power cable from being removed
by accident.
(Only 42PN45**)
M6
A
B
Power cord holder
(Only 50PN45**, 50/60PN65**)
Power cord holder
2
Gather and bind the cables with the Cable Holder.
CAUTION
y Disconnect the power first, and then move or
install the TV. Otherwise electric shock may occur.
y If you install the TV on a ceiling or slanted wall, it
may fall and result in severe injury.
Use an authorised LG wall mount and contact the
local dealer or qualified personnel.
y Do not over tighten the screws as this may cause
damage to the TV and void your warranty.
y Use the screws and wall mounts that meet the
VESA standard. Any damages or injuries by
misuse or using an improper accessory are not
covered by the manufacturer’s warranty.
NOTE
y Use the screws that are listed on the VESA
standard screw specifications.
y The wall mount kit includes an installation manual
and necessary parts.
y The wall mount bracket is not provided. You can
obtain additional accessories from your local
dealer.
y The length of screws may differ depending on the
wall mount. Make sure to use the proper length.
y For more information, refer to the manual supplied
with the wall mount.
Cable holder
CAUTION
y Do not move the TV by holding the cable holder
and power cord holder, as the cable holders may
break, and injuries and damage to the TV may
occur.
ENGLISH
ENG
Separate purchase(Wall Mounting Bracket)
19
20
MAKING CONNECTIONS
ENGLISH
ENG
MAKING CONNECTIONS
Antenna Connection
This section on MAKING CONNECTIONS mainly uses
diagrams for the PN45** models.
Connect various external devices to the TV and switch
input modes to select an external device. For more
information of external device’s connection, refer to the
manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC,
gaming devices, and other external devices.
Connect the TV to a wall antenna socket with an RF
cable (75 Ω).
NOTE
y The external device connection may differ from
the model.
y Connect external devices to the TV regardless of
the order of the TV port.
y If you record a TV program on a DVD recorder or
VCR, make sure to connect the TV signal input
cable to the TV through a DVD recorder or VCR.
For more information of recording, refer to the
manual provided with the connected device.
y Refer to the external equipment’s manual for
operating instructions.
y If you connect a gaming device to the TV, use the
cable supplied with the gaming device.
y In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast or
brightness. If noise is present, change the PC
output to another resolution, change the refresh
rate to another rate or adjust the brightness and
contrast on the PICTURE menu until the picture is
clear.
y In PC mode, some resolution settings may not
work properly depending on the graphics card.
ANTENNA/
CABLE IN
Wall Antenna
Socket
Add Isolator
NOTE
y Use a signal splitter to use more than 2 TVs.
y If the image quality is poor, install a signal amplifier
properly to improve the image quality.
y If the image quality is poor with an antenna
connected, try to realign the antenna in the correct
direction.
y An antenna cable and converter are not supplied.
y Supported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC
IN
ANTENNA/CABLE
MAKING CONNECTIONS
21
Transmits the digital video and audio signals from an
external device to the TV. Connect the external device
and the TV with the HDMI cable as shown.
Transmits the digital video signal from an external device
to the TV. Connect the external device and the TV with
the DVI-HDMI cable as shown. To transmit an audio
signal, connect an audio cable.
IN 1(PC)
Choose any HDMI input port to connect. It does not matter which port you use.
IN 1(PC)
DVI to HDMI connection
AUDIO IN (PC)
(Only 50/60PN65**)
IN 2
L/MONO
RED
WHITE
DVD / Blu-Ray / PC / HD
Cable Box /HD STB
(*Not Provided)
(*Not
Provided)
(*Not Provided)
(Only HDMI IN 1(PC))
HDMI
AUDIO OUT
NOTE
yy It is recommended to use the TV with the HDMI
connection for the best image quality.
yy Use the latest High Speed HDMI™ Cable with
CEC (Customer Electronics Control) function.
yy High Speed HDMI™ Cables are tested to carry an
HD signal up to 1080p and higher.
yy Supported HDMI Audio format : Dolby Digital,
PCM (Up to 192 KHz, 32k/44.1k/48k/88k/96k/176
k/192k, DTS Not supported.)
DVI OUT
DVD / Blu-Ray / HD Cable Box / PC
NOTE
yy Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.
ENGLISH
ENG
HDMI Connection
22
MAKING CONNECTIONS
Audio Connection
Transmits analog video and audio signals from an external device to the TV. Connect the external device and the
TV with a component cable as shown.
You may use an optional external audio system instead
of the built-in speaker.
Digital optical audio connection
Transmits a digital audio signal from the TV to an external device. Connect the external device and the TV with
the optical audio cable as shown.
AUDIO IN (PC)
AV IN 2
L/MONO
COMPONENT
IN
ENGLISH
ENG
Component Connection
RED
WHITE
RED
BLUE
GREEN
(*Not Provided)
RED
WHITE
RED
BLUE
GREEN
VIDEO
(*Not Provided)
AUDIO
OPTICAL AUDIO IN
Digital Audio System
DVD / Blu-Ray / HD Cable Box
NOTE
yy If cables are not installed correctly, it could cause
this image to display in black and white or with
distorted colours.
NOTE
yy Do not look into the optical output port. Looking at
the laser beam may damage your vision.
yy Audio with ACP (Audio Copy Protection) function
may block digital audio output.
MAKING CONNECTIONS
23
ENGLISH
ENG
Composite Connection
Transmits analog video and audio signals from an external device to the TV. Connect the external device and the
TV with th e composite cable as shown.
2
1
AUDIO IN (PC)
AV IN 2
AUDIO IN (PC)
L/MONO
L/MONO
AV IN 1
AV IN 1
COMPONENT
IN
COMPONENT
IN
AV IN 2
L/MONO
RED
WHITE
YELLOW
VCR / DVD / Blu-Ray / HD Cable Box
VIDEO
L(MONO) R
RED
AUDIO
WHITE
L(MONO) R
YELLOW
(*Not Provided)
VIDEO
L/MONO
(*Not Provided)
AUDIO
VCR / DVD / Blu-Ray / HD Cable Box
24
MAKING CONNECTIONS
Connect a USB storage device such as a USB flash
memory, external hard drive, or a USB memory card
reader to the TV and access the My media menu to use
various multimedia files.
(*Not Provided)
USB IN
ENGLISH
ENG
USB Connection
USB
REMOTE CONTROL
25
The descriptions in this manual are based on the buttons on
the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries
(1.5 V AAA) matching the and ends to the label inside
the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
ENGLISH
ENG
REMOTE CONTROL
or
CAUTION
yy Do not mix old and new batteries, as this may damage the remote control.
yy In Analogue TV and some countries, some remote control buttons may not work.
Make sure to point the remote control toward the remote control sensor on the TV.
Only PN45**
RATIO
POWER
Turns the TV on or off.
TV/
RAD
SUBTITLE
Recalls your preferred subtitle in digital
mode.
INFO
4
def
5
jkl
6
mno
pqrs
8
tuv
9
wxyz
[
FAV
GUIDE
MUTE
1
Navigation buttons (up/down/left/right)
Scrolls through menus
FAV or options.
P
OK
A
G
P confirms
E
Selects menus or options and
your
input.
MUTE
(Back)
Returns to
the previous level.
SETTINGS
MY APPS
Q.VIEW
Returns to the previously viewed
programme.
1 TELETEXT BUTTONS
These buttons are used for teletext.
3
0
Number buttons
Enters numbers.
ꕌPꕍ
Scrolls through the saved programmes
or channels.
ꕌPAGEꕍ
Moves to the previous or next screen.
abc
ghi
7
TV/RAD
Selects Radio, TV and DTV programme.
MUTE
Mutes all sounds.
2
Q. MENU
Accesses the
Q.VIEW
LISTquick menus.
INPUT
Changes the input source.
GUIDE
Shows programme guide.
.,;@
SETTINGS
Accesses the main menus.
Selects an AV mode.
RATIO
Resizes an image.
+
Adjusts the volume level.
FAV
Accesses your favourite programme list.
1
Views the information of the current
programme and screen.
AV MODE
LIST
Accesses the saved programme list.
INPUT
(FREEZE)
TV/
RAD using the
Freezes the current frame while
TV, AV, Component, or HDMI input source.
EXIT
Clears on-screen displays and return to TV
viewing.
OK
SLEEP
Accesses the AV devices connected with the
HDMI cable through HDMI-CEC.
Opens the SIMPLINK menu.
EXIT
SLEEP
Sets the length of time until the TV to
turns off.
2 Control buttons (
SUBTITLE
)
Controls the MY MEDIA menus, or
the SIMPLINK compatible devices
(USB,SIMPLINK).
REC
LIVE TV
2 Colour buttons
INFO
These access special functions in some
menus.
(
: Red,
: Green,
: Yellow,
:
Blue)
26
REMOTE CONTROL
ENGLISH
ENG
Only PN65**
POWER
Turns the TV on or off.
TV/RAD
Selects Radio, TV and DTV programme.
RATIO
Resizes an image.
INPUT
Changes the input source.
AV MODE
Selects an AV mode.
Number buttons
Enters numbers.
RATIO
+
Adjusts the volume level.
FAV
Accesses your favourite programme list.
GUIDE
Displays the program event according to
time scheduler.
AV MODE
TV/
RAD
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
P
A
G
E
GUIDE
MUTE
SETTINGS INFO
Q.MENU
EXIT
MUTE
Mutes all sounds.
ꕌPꕍ
Scrolls through the saved programmes or
channels.
PAGE
Moves to the previous or next screen.
SETTINGS
Accesses the main menus.
INFO
Views the information of the current
programme and screen.
Q. MENU
Accesses the quick menu.
OK
Selects menus or options and confirms your
input.
Accesses the AV devices connected with the HDMI
cable through HDMI-CEC.
Opens the SIMPLINK menu.
EXIT
Clears all on-screen displays and returns to
TV viewing.
1 Colour buttons
These access special functions in some
menus.
(
: Red,
: Green,
: Yellow,
: Blue)
2 TELETEXT BUTTONS
These buttons are used for teletext.
OK
BACK
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
(BACK)
Returns to the previous level.
FAV
LIST
Accesses the saved programme list.
Q.VIEW
Returns to the previously viewed programme.
INPUT
(FREEZE)
Freezes the current frame while using the
TV, AV, Component, or HDMI input source.
SUBTITLE
1 Recalls your preferred subtitle in digital mode.
TEXT
T.OPT
SUBTITLE
Control buttons (
)
2 Controls the MY MEDIA menus, or
the SIMPLINK compatible devices
(USB,SIMPLINK).
USING THE USER GUIdE
User Guide allows you to more easily access the detailed TV information.
Press SETTINGS to access the main menus.
Press the RED button to access the Customer
Support menus.
Press the Navigation buttons to scroll to User Guide
and press OK.
1
2
3
User Guide
1
OPTION > To set language
SETTINGS
OPTION
Language
You can select the language of the menu displayed on the screen and the digital
sound broadcasting.
y Menu Language : Selects a language for the display text.
y Audio Language [In Digital mode Only] : Select the desired language when
watching digital broadcasting containing several voice languages.
y Subtitle Language [In Digital mode Only] : Use the Subtitle function when two
or more subtitle languages are broadcast.
If subtitle data in a selected language is not broadcast, the default
language subtitle will be displayed.
PROGRAMME Setting
PICTURE, SOUND Setting
I
OPTION
Advanced Function
PICTURE
o
LOCK
AUDIO
OPTION
SETUP
INPUT
Information
TIME
MY MEDIA
SETTINGS
2
OPTION
Zoom In
Close
Language
You can select the language of the menu displayed on the screen and the digital
sound broadcasting.
Press OK() to set picture settings.
Customer Support
y Menu Language : Selects a language for the display text.
y Audio Language [In Digital mode Only] : Select the desired language when
watching digital broadcasting containing several voice languages.
y Subtitle Language [In Digital mode Only] : Use the Subtitle function when two
or more subtitle languages are broadcast.
If subtitle data in a selected language is not broadcast, the default
language subtitle will be displayed.
Exit
Software Update
Picture Test
Sound Test
2
Signal Test
Product/Service Info.
Zoom Out
Close
User Guide
Close
User Guide
3
2
To use input device
To set time options
PROGRAMME Setting
To set TV lock options
PICTURE, SOUND Setting
OPTION
To set language
To set country
Advanced Function
To set subtitle
Information
1
To set other options
1/1
1
Allows to select the category you want.
2
Allows to select the item you want.
You can use
to move between pages.
H
3
Allows to browse the description of the function
you want from the index.
27
ENGLISH
ENG
r
USING THE USER GUIDE
1
Shows the description of the selected menu.
You can use
to move between pages.
H
2
Zooms in or out the screen.
28
MAINTENANCE / TROUBLESHOOTING
ENGLISH
ENG
MAINTENANCE
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
yy Make sure to turn the power off and disconnect the power cord and all other cables first.
yy When the TV is left unattended and unused for a long time, disconnect the power cord from the wall outlet to
prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
yy Avoid touching the screen at all times, as this may result in damage to the screen.
yy Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in scratches
and image distortions.
yy Do not use any chemicals as this may damage the product.
yy Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
Problem
Solution
Cannot control the
TV with the remote
control.
yy Check the remote control sensor on the product and try again.
yy Check if there is any obstacle between the product and the remote control.
to ,
to
yy Check if the batteries are still working and properly installed (
No image display and
no sound is produced.
yy Check if the product is turned on.
yy Check if the power cord is connected to a wall outlet.
yy Check if there is a problem in the wall outlet by connecting other products.
The TV turns off
suddenly.
yy Check the power control settings. The power supply may be interrupted.
yy Check if the Auto sleep feature is activated in the Time settings.
yy If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of
inactivity.
When connecting to
the PC (HDMI (PC)),
‘No signal’ or ‘Invalid
Format’ is displayed.
yy Turn the TV off/on using the remote control.
yy Reconnect the HDMI cable.
yy Restart the PC with the TV on.
).
TROUBLESHOOTING
29
Problem
No sound is produced while
images are displaying.
One of the speakers produce
noises or does not produce
sound.
Solution
+ or - button.
Press
yy
Check if the sound is muted by pressing MUTE.
yy
Scroll to other channels. There may a problem with the broadcast.
yy
Check if the audio cables are connected properly.
yy
A change in ambient humidity or temperature may result in an unusual
yy
noise when the product turns on or off.
There is no problem with your product.
yy
Video
Solution
Problem
An image displays in black
Adjust the colour setting in the PICTURE menu.
yy
and white or the colour quality yy
Keep a sufficient distance between this product and other electronic
is poor.
products.
Scroll to other channels. There may a problem with the broadcast.
yy
Horizontal or vertical bars
Check if there are local interferences such as an electrical appliance
yy
appears or images blur
or power tool.
Lines or streaks appear on
Check the antenna or aim the antenna to the proper direction.
yy
images
Afterimages (ghosts) appear
Pixels may have been damaged from a fixed image displayed for
yy
when the product turns off
a long time (image burn). Use a screen saver to prevent the pixel
damage on the screen.
The power is on but the screen yy
Adjust the brightness and contrast in the PICTURE menu.
appears extremely dark.
“No Signal” appears on the
Check if the signal cable is connected between the TV and products
yy
screen.
properly.
Check the selected input source by pressing INPUT.
yy
Thin lines appear in the
Check the video cable connections.
yy
background of the screen.
The reception on some
Scroll to other channels. There may a problem with the broadcast.
yy
channels is poor
The station signal may be weak. Aim the antenna to the proper
yy
direction.
Check if there is local interference such as an electrical appliance or
yy
power tool.
ENGLISH
ENG
Audio
30
(19,5210(17$/,1)250$7,21
ENGLISH
ENG
SPECIFICATIONS
ENGLISH
ENG
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
For the power supply and power consumption, refer to the label attached to the product.
MOdELS
Dimensions
(W x H x D)
Weight
42PN4500-TA
50PN4500-TA
983.6 x 650.3 x 250.0
1168.0 x 755.4 x 292.7
Without stand (mm)
983.6 x 595.6 x 57.0
1168.0 x 698.6 x 57.0
With stand (kg)
19.6
25.4
Without stand (kg)
18.4
24.0
AC100-240V~ 50/60Hz
50PN65**
60PN65**
60PN6500-TB
60PN6500-TC
With stand (mm)
1168.0 x 755.4 x 292.7
1386.8 x 874.0 x 340.0
Without stand (mm)
1168.0 x 698.6 x 57.0
1386.8 x 821.7 x 57.0
26.1
37.7
With stand (kg)
Without stand (kg)
24.7
34.5
AC100-240V~ 50/60Hz
Power requirement
Operating Temperature
Environment
condition
AC100-240V~ 50/60Hz
50PN6500-TB
50PN6500-TC
MOdELS
Weight
50PN45**
With stand (mm)
Power requirement
Dimensions
(W x H x D)
42PN45**
Operating Humidity
AC100-240V~ 50/60Hz
0 °C to 40 °C
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
31
32
SPECIFICATIONS
ENGLISH
ENG
New Zealand,
Singapore
Television System
Programme
Coverage
Australia
Television System
Programme
Coverage
Indonesia,
Israel, Myanmar,
Sri Lanka
Television System
Programme
Coverage
Vietnam,
Malaysia
Television System
Programme
Coverage
Iran, Algeria,
Tunisia, Digital
model
Television System
Programme
Coverage
Analogue model,
India, Thailand,
South Africa, --
Television System
Programme
Coverage
External Antenna
Impedance
Digital TV
Analogue TV
DVB-T
PAL/SECAM-B/G/D/K, PAL-I
UHF 21 to 69
DVB-T
VHF 06 to 12,
UHF 27 to 69
DVB-T
UHF 21 to 69
DVB-T
VHF 6 to 12,
UHF 21 to 69
DVB-T
VHF 5 to 12,
UHF 21 to 69
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
PAL B/B
B/B : VHF/UHF 0 to 75, CATV : 2 to
44
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
-
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
-
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
75 Ω
75 Ω
SPECIFICATIONS
Component port connecting information
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720x480
31.469
31.5
59.94
60
720x576
31.25
50
1280x720
37.5
44.96
45
50
59.94
60
33.72
33.75
28.125
26.97
27
33.716
33.75
56.25
67.43
67.5
59.94
60
50
23.97
24
29.976
30.00
50
59.94
60
Resolution
1920x1080
HdMI/dvI-PC supported mode
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
640x350
31.468
70.09
720x400
31.469
70.08
640x480
31.469
59.94
800x600
37.879
60.31
1024x768
48.363
60.00
1360x768
47.712
60.01
1280x1024
63.981
60.02
1920x1080
67.5
60.02
(Only 50PN65**, 60PN65**)
Component ports on the
TV
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Signal
Component
480i/576i
O
480p/576p
O
720p/1080i
O
1080p
O
(50 Hz / 60 Hz only)
ENGLISH
ENG
HdMI/dvI-dTv supported mode
33
34
LICENSES / OPEN SOURCE SOFTWARE NOTICE / EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for
more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to
play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate
the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on
how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274”
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product,
please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for
download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such
distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is
valid for three (3) years from the date on which you purchased the product.
ExTERNAL CONTROL dEvICE SETUP
To obtain the external control device setup information, please visit www.lg.com
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring any
service.
MODEL
SERIAL
(Only DTV)
Download PDF

advertising