LG | 42PX4RV | LG 42PX4RV Owner’s Manual

PLASMA TV
OWNER'S MANUAL
Please read this manual
carefully
before
operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the back
mation to your dealer when you
Model number
:
Serial number
:
P/NO
:
38289U0555A
(MF056A,
require
151E
and quote this inforservice.
cover
TX)
Safety Warnings
Instructions
Safety
Safety
?
It is recommended that 42PX4RVH / 50PX4RH model
only
be used at
an
altitude of less than 6561 feet
(2000m)
to
get the best quality picture and sound.
W
WARNING
Do not
place the
sources
such
This may
-
use
or
place
any
This may
-
heat
as
cause a
Do not
set in direct
registers,
sunlight
stove and
near
heat
so on.
Do not
-
fire.
the set in
such
damp place
it is likely to get
where
cause a
or
fire
could
or
give
an
as a
bathroom
In
cable
antenna
building
to
and
damaged
cleaning the
damaged
cause
of smoke
or
the set
set.
could
or
give
an
electric
strange smell from the set, switch
from the wall outlet and contact your
service center.
,unplug it
or
This may
cause a
fire
or
could
give
an
electric shock.
outside
Do not
prevent rain from flowing in.
This may cause water
electric shock.
-
inside
between
case
dealer
electric shock.
-
Bend
This may
shock.
it off
wet.
water while
use
inside the set and could
give
an
attempt
your dealer
-
This may
shock.
or
to service the set
yourself. Contact
service center.
cause
damaged
the set
or
could
give
an
electric
Earth wire should be connected.
-
-
If the earth wire is not
connected, there is possible
electric shock caused
by
danger
a
of
the current
leakage.
If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician.
During
storm
activity, unplug the
outlet and don't touch
-
This may
shock.
cause
an
damaged
set from the wall
antenna cable.
the set
or
could
give
an
electric
DISCONNECTING DEVICE FROM MAINS
Power
-
supplier
Mains
plug is the disconnecting
readily operable.
device. The
plug
must remain
Short-circuit
breaker
-
Do not connect
ground
to
telephone wires, lightning
rods
or
gas
pipe.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
Do not insert any
This may
-
Do not
cause a
fire
or
could
give
place heavy objects
This may
-
object into the exhaust
cause
serious
injury
on
to
a
an
2
This set is
electric shock.
the set.
child
WARNING in U.K.
*
vent.
or
adult.
only
with a BS 1363 approved 13 amp mains plug, fused at 13 amp. When replacing the fuse
always use a 13 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse cover omitted. To
obtain a replacement fuse cover contact your dealer or "LG Electronics U.K. Ltd." If the type of plug supplied is not
suitable for the mains sockets in your home, then the plug should be removed and a suitable type fitted.
A mains plug removed from the mains lead of this set must be destroyed. A mains plug with bared wires is
hazardous if inserted in a mains socket. Do not connect either wire to the earth pin, marked with the letter E or
with the earth symbol
or coloured green or green and yellow. If any other plug is fitted, use a 13 amp fuse,
either in the plug, or at the distribution board.
The wires in this mains lead are coloured in accordance with the following codes: BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this set may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected
to the terminal which is marked with the letter L or coloured red.
PLASMA TV
supplied
Safety Warnings
*
instructions have two kinds of information, and each
Safety
of it is
meaning
as
below.
WARNING The violation of this instruction may
cause
serious
The violation of this instruction may
cause
light injuries
NOTES
injuries
and
even
damage
or
death.
of the
product.
Take
care
of
danger that may happen
under
specific condition.
NOTES
Never touch the power
-
This may
cause an
plug with
a
wet hand.
Ensure the power cord doesn't trail
objects like a heater.
electric shock.
-
Disconnect from the mains and
tions before
remove
all
bookcase
-
or
Ventilation
or an
electric shock.
Do not
plug in unit if power cord or plug is damaged
the connecting part of the power outlet is loose.
moving.
place the
fire
cause a
any hot
connec-
-
Do not
This may
across
set in
a
built-in installation such
as a
This may
fire
cause a
or an
or
electric shock.
rack.
Dispose of used batteries carefully
from eating them.
required.
-
In
case
of
a
child
eating them,
to
prevent
contact doctor
a
immediately.
When
moving the set assembled with speakers
carry holding the speakers.
-
This may cause the set to fall, causing serious
adult, and serious damage to the Monitor.
child
injury to
a
do not
child
or
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
When
installing the set on a table, be careful not
place the edge of its stand on the end of the table.
-
This may cause the set to fall, causing serious
adult, and serious damage to the set.
injury
to
a
child
to
or
-
This may
cause
damage
the set
Contact the service center
or
could
once a
give
an
electric shock.
year to clean the
internal part of the set.
-
Accumulated dust
can cause
mechanical failure.
The distance between eyes and the screen should be
7 times the diagonal length of the screen
approx. 5
~
away.
-
If not, eyes will strain.
Unplug the set from the wall outlet when it is left unattended
and unused for long periods of time or occurred a state of
emergency.
-
Do not
place
an
outside antenna in the
head power lines
cuits.
-
This may
cause an
or
vicinity of overother electric light or power cir-
Accumulated dust may cause a fire or
deterioration through electric leakage.
an
electric shock from
electric shock.
There should be
antenna and
enough distance between an outside
power lines to keep the former from
touching the latter
-
This may
Do not
-
even
cause an
pull the plug
This may
cause a
when the antenna falls.
electric shock.
not the cord when
disconnecting.
fire.
Owner's Manual
3
Contents
Contents
Contents
Time Menu
Safety Warnings
SafetyInstructions.......................2~3
Introduction
RemoteControlKeyFunctions................6
LocationandFunctionofControls
.
.
.
.
.
.
.
.
.
.
.7~8
ChildLock..............................27
Installation
External
Equipment Viewing Setups
Displayable Monitor Specification
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.9~12
.
.
.13
HDMI...............................14~15
Accessories.............................16
InstallationOptions.......................17
Operation
TurningontheSet........................18
On-Screen Menu Language Selection (option)
.18
Channel Menu Options
AutoProgrammeTuning...................19
ManualProgrammeTuning.................19
FineTuning.............................20
AssigningaStationName..................20
Booster(option)..........................20
ProgrammeEdit..........................21
FavouriteProgramme.....................21
.21
CallinguptheProgrammeTable
Picture Menu Options
PSM(PictureStatusMemory)...............22
CSM(ColourStatusMemory)...............22
Manual Colour Temperature Control
.22
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
sRGB.................................23
ACM(ActiveColourManagement).
.
.
.
.
.
.
.
.
.
.
.23
ManualPictureControl....................23
Sound Menu
Options
SSM(SoundStatusMemory)................24
BBE...................................24
AVL(AutoVolumeLeveler).................24
AdjustingSoundControl...................24
TVspeaker.............................25
Stereo/DualReception.....................25
NICAMReception(option)..................25
reading this manual,
keep it in a place where the
user can refer to easily.
4
PLASMA TV
ISM
Method
(Image Sticking Minimization)
.
.
.
.
.
.27
LowPower..............................28
Demo.............................28
Screen Menu
Options
AutoConfigure..........................29
ManualConfigure........................29
SelectingWideVGA/XGAmode.............29
SettingPictureFormat.....................30
PictureSizeZoom........................30
.
..................................22
After
Options
SettingtheClock.........................26
SettingtheOn/OffTimer...................26
AutoSleep..............................26
SleepTimer.............................26
Special Menu Options
ScreenPosition..........................31
Cinema................................31
NR(NoiseReduction).....................31
.31
Initializing (Reset to original factory value)
PIP (Picture-in-Picture) Feature
WatchingPIP............................32
.32
Programme Selection for Sub Picture
.32
Selecting an Input Signal Source for the PIP
.32
MovingthePIP(PIPmodeonly).
POP (Picture-out-of-Picture: Channel Scan)
.32
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PictureSize.............................32
AdjustingthescreenforthePIP.
Adjusting PIP Transparency (PIP mode only)
Teletext (option)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.32
.32
Switchon/off............................33
SIMPLEText(option)......................33
TOPText(option).........................33
FASTEXT..............................34
SpecialTeletextFunctions..................34
Miscellaneous
.35~41
ExternalControlDeviceSetup
IRCode(NECFormat)..................42~43
ProgrammingtheRemote..................44
ProgrammingCodes...................45~46
TroubleshootingChecklist..................50
ProductSpecifications.....................51
.
.
.
.
.
.
.
.
.
.
.
Introduction
Introduction
What is
a
Plasma
Display
?
If
voltage is inputted to gas in glass panels, ultraviolet rays are outputted and fused with a fluorescent substance.
light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160°
-
Wide
A Plasma
At this moment,
range of vision
angle
Display provides
than 160°
more
angle
range of vision
so
that you
can
get
a
picture
without distortion from any
direction.
Easy
installation
A Plasma
in the
Display is
desired place.
Big
screen
The
screen
of
a
much
Plasma
Multimedia Plasma
A Plasma
and
The
Display
can
lighter
Display
and smaller than other
is 42"
(or 50")so
same
that you
can
so
that you
get vivid experience
as
can
if you
install the Plasma
are
in
a
Display
theater.
Display
be connected with
a
computer
so
that you
explanation
about coloured dots may be present
display
device of this
product
is
composed
in the manufacture of the PDP. Several coloured dots visible
manufacturers and would not
mean
that the PDP is
faulty.
sponds to this standard is regarded as acceptable. It means
We promise that we'll do our best to develop our technology
explanation
In the
it
can use
as a screen
for conference, game, internet
about noise of 42"
(or 50")
PDP
on
We
on
PDP
screen
of 0.9 to 2.2 million cells and
the
screen
would be
a
few cell defects
acceptable,
can occur
in line with other PDP
you will understand that the product which
that it could not be changed or refunded.
to minimize the cell defects.
hope
corre-
(option)
way that a fan is used in a PC to keep the CPU cool, the PDP is equipped with cooling fans to improve the
of this product. Therefore, a certain level of noise could occur when the fan is operated. This noise doesn't have
same
reliability
any negative
effect
on
The noise from the fans
is
products
so on.
The PDP which is the
The
class
acceptable.
It
means
its
reliability and it's also determined to have no difficulty while using this product.
is normal in the operation of this product. We hope you will understand that a certain level of noise
that it is not changeable nor refundable.
efficiency
and
TO AVOID BURNING IMAGE INTO THE
DISPLAY, DO NOT HAVE A STILL IMAGE ON SCREEN FOR EXTENDED PERIOD
OF TIME. IMAGE AFTER BURN WILL NOT BE COVERED UNDER WARRANTY
ie.Menus, Video games, Borders
or
LOGOS
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
Owner's Manual
5
Introduction
Remote Control
Control
-
-
Key
Functions
When
using the remote control aim it at the remote control sensor of the set.
There's maybe a defect in consecutive operation of remote control in specified brightness according
POWER
switches the set
INPUT
Selects the TV, AV, Component, RGB or
HDMI modes.
switches the set on from standby.
DVD
TV
VCR
MODE
AUDIO
STB
ZOOM- /ZOOM+
reduces the main
picture
ZOOM
size.
-
ZOOM
+
TEXT/
SLEEP
Sets the sleep timer.
MUTE
Switches the sound
MUTE
PIP
LIST
SLEEP
*
by
on or
HDMI
off.
ARC
I/II
Selects the language during
guage broadcast.
Selects the sound output.
EXIT
MENU
on screen menus one
off to
or
I/II
MENU
Displays
standby
MULTIMEDIA
Selects the Component, RGB or
modes.
switches the set on from standby.
CABLE
or
from
POWER
MODE
Selects another device.
Enlarges
on
standby.
MULTIMEDIA
INPUT
to this set feature.
dual
lan-
one.
Exits the current menu.
Memorizes menu changes.
LIST
OK
PIP
Switches the sub picture on or off.
Selects PIP or DW modes.
PIPPR+/Selects a programme for the sub picture.
SWAP
Alternates between main and sub picture.
PIP INPUT
Selects the input mode for the sub picture.
SIZE
Adjusts the sub picture size.
POSITION
PIPPR-
PIPPR+
Displays
SWAP
the programme table.
EXIT
Clears all on-screen displays and returns
to TV viewing from any menu.
PIPINPUT
ARC
VOL
SSM
PSM
Changes
PR
the
picture
format.
OK
accepts your selection
or
displays
the
cur-
rent mode.
D/EorF/G
Adjusts menu settings.
MovesthesubpicturetoD/EorF/G
direction.
Selects
SSM
To select the sound
appropriate to your
viewing programme.
FAVOURITE
POSITION
INDEX
HOLD
TIME
REVEAL
MIX
MODE
item.
VOL +/- (Volume Up/Down)
Increases/decreases sound level.
PR +/- (Programme Up/Down)
Selects a programme.
Q.VIEW
SIZE
menu
NUMBER buttons
?
PSM
M
Adjusts the factory preset picture
ing to the room.
FAVOURITE
selects
a
favorite programme.
Q.VIEW
TEXT/*
Returns
These buttons are used for teletext.
For further details, see the 'Teletext' section.
Note : In teletext mode, the PIP PR +/-,
SWAP and PIP INPUT buttons are used for
teletext function.
Installing
the
previously
?
PLASMA TV
viewed
pro-
gramme.
VCR BUTTONS
Controls a LG video cassette recorder.
Open
the
6
to
Batteries
?
accord-
the
battery compartment cover
batteries with correct polarity.
on
the back side and insert
Install two 1.5V alkaline batteries of AA type. Don't mix used batteries with new batteries.
Introduction
Location and Function of
of Controls
Controls
<Front Panel Controls>
7
8
TV/AV
INPUT
2
on
from
standby
or
off to
standby.
Selects
F / G
Selects the TV, AV,
Component, RGB
on from standby.
or
Adjusts
Adjusts
HDMI modes.
(Programme Up/Down)
a
programme
Exits the current
Memorizes
menu
by
from
standby.
(Volume Up/Down)
on
the volume.
menu
settings.
Illuminates red in
on screen menus one
item.
or a menu
7. Power Indicator
4. MENU
Displays
PR
PR
Switches the set
3. INPUT Button
VOL
OK
6
6. D / E
2. Remote Control Sensor
Switches the set
VOL
OK
1345
1. Power Button
Switches the set
MENU
MENU
set is turned
one.
standby mode,
Illuminates green when the
on.
menu.
8.
changes.
Intelligent Eye
Adjusts picture according
to the
surrounding
conditions.
5. OK
Accepts
your selection
or
displays
the current mode.
Owner's Manual
7
Introduction
Location and Function of
of Controls
Controls
-
-
-
Shown is
a
of the set.
simplified representation
What is shown here may be somewhat different from your set.
This manual explains the features available on the 42PX4RV series.
<Back Panel>
A V
NPUT2
S-VIDEO
VIDEO
9
L/MON
AUDIO
R
V DEO
AUD
AUD
V DEO
O
O
AC INPUT
L
HDMI/
COMPONEN
RGB INPUT
AUDIO INPUT
DVI(VIDEO)
NPU
R
2
L
MON
Antenna
R
OROU
PU
AUD
L
VAR
O
R
ABLE AUD O OUT
RS-232C INPUT
REMOTE
CONTROL
(CONTROL/SERVICE)
(MONO)
COMPONEN
1
1.
2
HDMI(DVI VIDEO)
NPU
4
3
/ AUDIO INPUT / RGB INPUT
Connect the monitor output socket of the PERSONAL COMPUTER, DVD or STB to this socket.
Note: If you want to use RGB/DVI audio, we strongly
recommend that you use the cable that has a core, or the
EMI Filter core along with separate cable.
2.
REMOTE CONTROL
3.
RS-232C
4.
on a
PORT
PC.
COMPONENT INPUT
VIDEO/AUDIO IN/OUT SOCKETS
(A/V
Connect the video/audio out sockets of
INPUT
1)
external equipment
to these sockets.
S-VIDEO/AUDIO IN SOCKETS
Connect the S-VIDEO out socket of
an
VCR to the S-VIDEO
socket.
Connect the audio out sockets of the VCR to the audio sockets
8
as
in A/V INPUT 1.
PLASMA TV
5
6
7
8
6.
VARIABLE AUDIO OUTPUT
7.
ANTENNA INPUT
8.
POWER CORD SOCKET
This Monitor operates on AC power. The voltage is indicated
on the Specifications page. Never attempt to operate the set
9.
DC power.
AUDIO/VIDEO INPUT
(A/V
INPUT
S-VIDEO/AUDIO IN SOCKETS
Connect DVD video outputs to Y, PB, PR of COMPONENT
INPUT and audio outputs to Audio sockets of AUDIO INPUT.
5.
SVDEO
on
INPUT(CONTROL/SERVICE)
Connect to the RS-232C port
AVNPU
2)
Installation
External
Equipment
V
iewing
Viewing
Setups
Antenna Connection
-
Be careful not to bend the bronze wire when
Apartments
(connecting
to wall antenna
connecting
to
an
antenna
port.
socket)
A ntenna
wall antenna socket
<
RF coaxial wire
Back
panel
of the set
>
(75 ohms)
VHF antenna
UHF antenna
outdoor antenna
Private house
to wall outdoor
(connecting
antenna)
Watching VCR
-
-
-
-
When
connecting
(R) -red).
Connect the VIDEO INPUT socket
(yellow)
of external
equipment
connecting ports (Video
to the VIDEO INPUT
on
-
yellow,
Audio
(L)
If
a
To
a
VCR.
(Refer
having
a
fixed
image
remain
on
the
screen
for
a
long period
picture format is used, the fixed image may remain visible on the screen.
avoid picture noise (interference), leave an adequate distance between the VCR
of time.
Typically
a
frozen still
pic-
and set.
TV programmes
Turn the set on and select the programme you
AUDIO INPUT
or
on
COMPONEN
NPU
V DEO
AUD
L
R
MON
2
OR
of the set
R
OU
PU
O
R
O OU
RS-232C INPUT
(CONTROL/SERVICE)
connected to the S-VHS VCR
the S-VIDEO
L
VAR ABLE AUD
AV2.
>
O
the remote control to
If both S-VIDEO and VIDEO sockets have been
Insert
RGB INPUT
O
panel
AUD
Use the INPUT button
only
AUD
L
VCR
Back
<
V DEO
select AV1
2.
VCR
regular
4:3
Watching
-
a
27)
to p.
want.
1.
white, Audio
the set.
Watching
-
-
input.
Use the orbiter function to avoid
ture from
-
equipment,
match the colours of
If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the set.
If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting
to the Video
-
the set to external
can
(MONO)
COMPONEN
NPU
1
AVN
1
SV
EO
simultaneously,
be received.
video tape into the VCR and press the
PLAY button on the VCR.
(See
a
VCR owner's
manual)
<VCR>
Owner's Manual
9
Installation
External
Watching Cable
After
-
Equipment
V
iewing
Viewing
Setups
Setups
TV
for
subscribing
local cable TV station and
a
installing
a
converter you
can
watch cable TV.
For further information of cable TV, contact the local cable TV station.
-
<
Back
panel
of the set
To watch cable TV
>
1.
V DEO
AUD
L
O
COMPONEN
NPU
V DEO
AUD
R
MON
OR
select AV1
R
OU
the remote control to
on
O
L
2
Use the INPUT button
PU
-
AUD
L
VAR ABLE AUD
O
or
AV2.
If both S-VIDEO and VIDEO sockets have been
connected to the Cable box
R
O OU
the S-VIDEO
can
simultaneously, only
be received.
(MONO)
COMPONEN
NPU
<
Watching
-
When
on
1.
Cable box
S
EO
an
equipment:
external source, match the colours of AUDIO/VIDEO input
Video
yellow, Audio (Left) white, Audio (Right) red.
=
=
jacks
on
the set with the output
jacks
=
use
Use the INPUT button
or
on
<
the remote control to
If both S-VIDEO and VIDEO sockets have been
only
Operate
the
See external
can
V DEO
simultaneously,
be received.
corresponding external equipment.
equipment operating guide.
AUD
L
AUDIO INPUT
RGB INPUT
panel
of the set
>
COMPONEN
NPU
O
AUD
V DEO
O
L
R
MON
2
OR
R
OU
PU
AUD
L
VAR ABLE AUD
RS-232C INPUT
(CONTROL/SERVICE)
(MONO)
COMPONEN
Camcorder
Video game set
PLASMA TV
Back
AV2.
the S-VIDEO
10
Select your desired channel with the remote
control for cable box.
>
connected to the S-VHS VCR
2.
2.
1
source
the set to
the audio/video
select AV1
-
AVN
external AV
connecting
How to
1
R
NPU
AUDIO
1
AVU
L
VIDEO
1
SV
EO
Installation
DVD
Watching
How to connect
<
Back
of the set
panel
>
Connect DVD video outputs to Y, PB, PR of COMPONENT INPUT and audio outputs to Audio sockets of
AUDIO INPUT.
V DEO
AUD
L
How to
use
Turn
1.
on
NPU
V DEO
AUD
R
O
L
MON
2
OR
R
OU
PU
AUD
the DVD
Use INPUT
2.
COMPONEN
RGB INPUT
O
or
player,
and insert
DVD.
a
O
L
R
VAR ABLE AUD O OU
RS-232C INPUT
MULTIMEDIA button
the remote
on
(CONTROL/SERVICE)
(MONO)
control to select
Refer to the
1
Component
DVD
Component
or
manual for
player's
COMPON
2.
NPU
N
AV
NPU
1
SVDEO
operating
instructions.
Component Input ports
You can get better picture quality if you
DVD player with component input ports as
?
Component ports
of the
connect
below.
YPBPR
set
Y
Y
Y
Y
Video output ports
of DVD player
Pb
B-Y
Cb
PB
Pr
R-Y
Cr
PR
<
Watching
-
To watch
DTV (option)
digitally
broadcast programs,
purchase
and connect
a
digital set-top
DVD
player
>
box.
How to connect
1.
Use the set's COMPONENT (Y, PB, PR) INPUT, RGB or
HDMI jack for video connections, depending on your settop box connector. Then, make the corresponding audio
connections.
How to
1.
2.
?
DTV
Input signal
Terminal
Mode
Component
RGB
(DTV)
HDMI
(DTV)
480i
o
x
x
576i
o
x
x
480p
o
o
o
576p
o
o
o
720p
o
o
o
1080i
o
o
o
use
Turn on the digital set-top box. (Refer to the owner's
manual for the digital set-top box.)
Use INPUT or MULTIMEDIA on the remote control to
select Component 1, Component 2, RGB or HDMI.
<
Back
panel
of the set
>
V DEO
AUD
L
HDMI/
DVI(VIDEO)
R
RGB INPUT
AUDIO INPUT
COMPONEN
NPU
MPON
NPU
O
AUD
V DEO
O
L
R
MON
2
OR
R
OU
PU
RS-232C INPUT
E
C
(CONTROL/SERVICE)
L
(MONO)
or
HDMI OUTPUT
AVNPU
1
SVDEO
or
(R)
<
AUDIO
(L)
Digital Set-top
HDMI OUTPUT
box
(R)
AUDIO
(L)
Y
PB
PR
>
Owner's Manual
11
Installation
External
V
iewing
Viewing
Equipment
Setups
Setups
Connecting PC
-
-
-
-
-
To
enjoy vivid picture and sound, connect a PC to the set.
Avoid keeping a fixed image on the set's screen for a long period of time. The fixed image may become permanently imprinted on
the screen; use a screen saver when possible.
Connect PC to the RGB INPUT(PC INPUT) or HDMI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output
of PC accordingly.
There might be noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode into
another resolution or change the refresh rate into another rate or adjust the brightness and contrast on the menu until the picture
is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the manufacturer of the PC graphic card.
The synchronization input waveform for Horizontal and Vertical frequencies are separate.
Setup Instructions to Connect a PC to your set
We recommend using 1024x768, 60Hz for the PC mode, they provide the best picture quality.
In 42PX4RV series, we recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality.
If the resolution of PC is over UXGA, there will be no picture on the set.
Connect the signal cable from the monitor output port of the PC to the RGB INPUT port of the set or the signal
-
-
cable from the
-
-
-
-
-
-
-
-
-
HDMI output port of the PC to the HDMI INPUT port on the set.
Connect the audio cable from the PC to the Audio input on the set.
If
sound card,
This set uses a VESA
using
a
adjust PC sound as required.
Plug and Play Solution. The set provides
(Audio
cables
are
not included with the
EDID data to the PC system with
a
DDC
set).
protocol.
The PC
adjusts
automatically to use this set.
DDC protocol is preset for RGB (Analog RGB), HDMI (Digital RGB) mode.
If required, adjust the settings for Plug and Play functionally.
If graphics card on the PC does not output analog and digital RGB simultaneously, connect only one of RGB INPUT or HDMI
INPUT to display the PC on the set.
If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or HDMI ; (the other mode
is set to Plug and Play automatically by the set.)
DOS mode may not work depending on video card if you use a HDMI to DVI cable.
When you use too long RGB-PC cable, there might be a noise on the screen. We recommend using under 5m of the cable. It provides the best picture quality.
<
Back
panel
of the set
PC
>
V DEO
AUD
L
HDMI/
DVI(VIDEO)
COMPONEN
RGB INPUT
AUDIO INPUT
NPU
2
O
V DEO
AUD
R
O
L
MON
OR
1. Turn
on
the PC and
apply power to the set.
display by pressing the POWER
2. Turn
on
the
3. Use the INPUT
PU
or
MULTIMEDIA button
control to select the RGB
C
L
RS
UT
(CO
CE)
4. Set the resolution
or
HDMI
input
output of the PC
COMPONEN
12
PLASMA TV
NPU
AVNPU
1
SVDEO
(1280
x
on
on
the remote
source.
to SXGA
(MONO)
1
button
the set's remote control.
R
OU
Setup
1024, 60Hz). (Refer to p. 13)
or
under
Installation
Displayable
Monitor
RGB / HDMI mode
Resolution
RGB / HDMI mode
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
31.468
852x480
800x600
832x624
1152x870
1280x960
1280x1024
Vertical
Frequency(KHz) Frequency(Hz)
31.468
70.09
37.861
85.08
37.861
85.08
31.469
70.08
31.469
70.08
720x400
37.927
85.03
37.927
85.03
31.469
59.94
31.469
59.94
35.000
66.66
35.000
66.66
37.861
72.80
37.861
72.80
37.500
75.00
37.500
75.00
43.269
85.00
43.269
85.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
75.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
75.00
35.156
56.25
35.156
37.879
60.31
37.879
60.31
48.077
72.18
48.077
72.18
46.875
75.00
46.875
75.00
53.674
85.06
53.674
85.06
49.725
74.55
49.725
74.55
48.363
60.00
48.363
60.00
56.476
70.06
56.476
70.06
1024x768
1152x864
Horizontal
640x350
720x400
848x480
Resolution
70.09
640x350
640x480
Specification
Specification
640x480
848x480
852x480
800x600
832x624
56.25
(RGB)
1024x768
60.023
75.02
60.023
75.02
68.677
85.00
68.677
85.00
54.348
60.05
47.700
60.00
63.995
70.01
59.625
75.02
67.500
75.00
68.500
85.00
68.681
75.06
47.700
60.00
60.023
60.02
59.625
75.02
63.981
60.02
69.500
85.00
54.348
60.05
63.995
70.01
67.500
75.00
77.487
85.00
68.681
75.06
47.693
60.00
60.091
75.00
68.504
85.00
1280x960
60.023
60.02
1280x1024
63.981
60.02
1360x768
1366x768
42PX4RV series
1152x864
1152x870
1280x768
50PX4R series
Owner's Manual
13
Installation
HDMITM, the HDMI logo and High-Definition Multimedia Interface
registered trademarks of HDMI Licensing.
This set can receive the High-Definition Multimedia Interface (HDMI) or Input of Digital Visual Interface(DVI).
This set supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the set (480p, 720p, 1080i) modes.
When you connect to HDMI/DVI Source devices (DVD Player, STB or PC) that support AUTO HDMI/DVI Plug & Play, this sets
the HDMI/DVI source devices automatically. (640 x 480p) (or 50PX4R series: 1280 x 720p).
Afer reading HDMI/DVI source devices, using Display Data Channel (DDC) Protocol, Extended Display Identification Data
(EDID) stored in the set is used.
If HDMI/DVI Source devices do not support AUTO HDMI/DVI, the resolution is set manually.
To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 640 x 480p (or 50PX4R series: 1280 x 720p).
To get the best picture quality, adjust the PC graphics card to 640 x 480 (or 50PX4R series: 1024 x 768), 60Hz.
When Source Devices have DVI Output Connector, you must connect audio with separated cable.(Refer to <How to connect>)
-
-
-
-
-
-
-
are
trademarks
or
How to connect
1. When Source Devices
If Source Devices
-
(DVD Player or Set Top Box) support HDMI.
have HDMI Output Connector, Source Devices connect
to the set with HDMI Cable
.(not supplied
with the
prod-
uct).
If Source Devices support Auto HDMI,
automatically, Source Devices divert output resolution in 640x480p (or 50PX4R
1280 x 720p). But if not, resolution divert Manually Setting for reference Manual of Source Devices.
To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 640x480p (or 50PX4R series:
720p).
Because HDMI sends Digital Video and Audio with one cable, there is no need for Audio Cable when using HDMI Cable.
-
-
-
1280
x
2. When Source Devices
If Source Devices
-
(DVD Player or Set Top Box) supports DVI.
have DVI Output Connector, Source Devices connect
series:
to the set with HDMI to DVI Cable
(not supplied
with the
product).
If Source Devices support Auto DVI,
automatically, Source Devices divert output resolution in 640x480p (or 50PX4R series: 1280
x 720p). But if not, resolution divert Manually Setting for reference Manual of Source Devices.
To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 640x480p (or 50PX4R series: 1280 x
720p).
In this case, Audio use other cable. When Source Devices have Analog Audio Output Connector, RGB/DVI Audio Input of the set
connect to Audio Cable (not supplied with the product). And then you can listen to normal Audio.
-
-
-
3. When PC
Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not supplied with the product).
To get the best picture quality, adjust the PC graphics card to 640x480 (or 50PX4R series: 1024 x 768), 60Hz.
Use the the set's HDMI/DVI (VIDEO) for video connections, depending on your PC connector.
If the graphics card on the PC does not output analog RGB and DVI simultaneously, connect only one of either RGB Input or
HDMI/DVI Input to display the PC on the set.
If the graphics card on the PC does output analog RGB and DVI simultaneously, the set to either RGB Input or HDMI/DVI Input;
(the other mode is set to Plug and Play automatically by the set.)
Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.
In this case, Audio use other cable. When PC (or sound card of PC) have Analog Audio Output Connector, RGB/DVI Audio Input
of the set connect to Analog Audio Cable (not supplied with the product). And then you can listen to normal Audio.
-
-
-
-
-
-
-
14
If PC has
supports DVI.
a
DVI
PLASMA TV
Installation
Reference
Cable
sample
HDMI Cable
(not supplied
with the
Analog
product)
(not supplied
How to
with the
3.
4.
with the
product)
product)
use
1. Connect the HDMI/DVI Source
2. Turn
(RCA type)
Analog Audio Cable (Stereo to RCA type)
(not supplied with the product)
HDMI to DVI Cable
(not supplied
Audio Cable
Devices(DVD Player
or
Set
Top
Box
or
PC)
and the set.
display by pressing the POWER button on the set and HDMI/DVI Source Devices remote control.
Select HDMI/DVI Input source in Main Input option of PIP/DW menu.
Check the image on your set. There may be noise associated with the resolution, vertical pattern, contrast or brightness in
HDMI/DVI Source Devices. If noise is present, change the HDMI/DVI Source Devices to another resolution, change the refresh
rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not
changed, change the PC graphics card or consult the manufacturer of the PC graphics card.
on
the
Notes:
-
-
-
Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI Cable.
Avoid keeping a fixed image on the set screen for a long period of time. The fixed image may become permanently imprinted on
the screen. Use the Orbiter screen saver when possible.
When Source Devices connected HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position, Size may not fit to Screen.
As shown the lower picture, press the MENU button to adjust the screen Position of the set and contact an PC graphics card service center.
-
-
When Source Devices connected HDMI/DVI
B
Specification
In
case
In
set
Resolution(480p, 720p, 1080i), the
set
Display fit EIA/CEA-861-
to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service center.
connected, Cable or poor cable connection, "No Signal" OSD display in HDMI/DVI
of Video Resolution not supported when output is HDMI/DVI Source Devices, "No Signal" OSD display. Refer
of HDMI/DVI Source Devices
Input. And
Input output the
case
are
not
to the Manual of HDMI/DVI Source Devices or contact your service center.
Owner's Manual
15
Installation
Accessories
NPUT
MULTMEDIA
POWER
DVD
TV
VCR
MODE
CABLE
O
STB
AUD
I
ZOOM
PIP
ZOOM
-
SLEEP
*
+
MUTE
LIST
III
TEXT/
ARC
MENU
EXIT
OK
PIPPR-
VOL
PP PR+
SSM
SWAP
PIPINPUT
PSM
FAVOURITE
PR
Q.VIEW
SIZE
POSTON
NDEX
HOLD
TIME
REVEAL
MIX
MODE
?
M
LG TV
ASmark
Remote Control handset
Owner's Manual
2-Eye
Bolts
1.5V
1.5V
Power Cord
Alkaline batteries
Fixing
-
the set
Secure the set
assembly
to the wall to
assembly by fixing
it to
a
protect the
wall
by using
Eye
Bolts/Wall brackets.
Secure the TV
assembly to the
(not supplied with the product),
?
-
tumbling
If the set is mounted on a desk top, insert the 2 Eye-Bolts and tighten them
securely in the upper holes as shown.
Insert the 2 Eye Bolts and tighten securely, in the holes on the bracket.
Install the wall brackets on the wall with 2 bolts, (not supplied with the product),
as shown.
Match the height of the Eye Bolts and the wall brackets.
Check to be sure the brackets are tightened securely.
?
Optional
the
set
2-Wall brackets
wall with strong
as shown.
strings
or
wound wire cables,
Extras
Optional
extras
can
be
changed
or
modified for
quality improvement.
Without any notification
new
optional
extras
can
added.
-
Contract your dealer for
buying
these items.
2
4
40
40
50
Tilt wall
16
mounting
PLASMA TV
bracket
42
Ceiling mounting
bracket
Video cables
Audio cables
be
Installation
Installation
?
?
The set
Options
Options
be installed in different ways such as on a wall, or on a desktop etc.
Install this set only in a location where adequate ventilation is available.
can
Wall Mount: Horizontal Installation
The set
?
can
be installed
on a
(For further information, refer
Mounting Bracket Installation
To Mount
on a
wall
as
Desktop
shown above.
?
Pedestal Installation
The set
can
be mounted
on a
desk
as
shown above.
to the
optional 'Wall
Setup Guide'.)
and
Wall
To Install
on a
Desktop
Wall mount minimum allowable clearances for ade-
Pedestal mount minimum allowable clearances for
quate ventilation.
adequate
ventilation.
10cm
3cm
10cm
10cm
10cm
Swivel function
After
(option)
installing
position.
?
Note
can
adjust
the set
manually
to the left
or
right
direction
by
20
degrees
to suit your
viewing
you must loosen (to the left) the shaft bolt on the middle of stand's back. And when
stand be level with set, you must close (to the right) the shaft bolt to set the hole.
:
Before
the set, you
adjusting the angle,
Owner's Manual
17
Operation
T
urning
Turning
-
When
using
Turning
on
the remote control, aim it at its
the set
/
Turning
If the set
on
the set
was
Press the
?
correctly,
I, INPUT
NUMBER buttons
on
or
the set is switched to
PR D /
E
button
/
menus can
(power cord
is still
I, INPUT
on
or
PR D /
or
mode.
press the POWER, INPUT, MULTIMEDIA, PR D /
E
be shown
on
the
screen
2. Press the G button and then
use D
3. Press the G button and then
use D
point
on, the
on-screen
PLASMA TV
E or
on.
connected)
button
on
the set
or
in the selected
use D
on
Selection
Selection
First select your
/ E button to select the SPECIAL
language.
menu.
Language.
/ E button to select your desired language.
menus will be shown in the language of your choice.
viewing.
the set
E or
on.
language.
/ E button to select
/ I button
press the POWER, INPUT, MULTIMEDIA, PR D /
Language
4. Press the EXIT button to return to normal TV
18
the set
the remote control to turn the set
1. Press the MENU button and then
From this
on
standby
the remote control and then the set will switch
On-Screen
On-Screen Menu
The
the set.
turned off with the remote control power button and the
NUMBER button
-
sensor on
after installation
just
1. Connect power cord
2. Press the
the Set
Set
on
on
(option)
(option)
Operation
Channel
Channel Menu
Auto
-
Options
Options
Programme Tuning
All stations that
be received
can
are
stored
by
this method. It is recommended that you
use
auto programme
during
installation of this set.
1. Press the MENU button and then
2. Press the
/
E
button to select the STATION
menu.
STATION
BG
/Australia)
PAL I/II (U.K.
/ E
(Europe
/ East
Europe
:
G
PICTURE
Programme
System
BG
Storage from
edit
Favourite programme
2
Start
SOUND
TIME
/ Asia / New Zealand / M.East / Africa
SPECIAL
Hong Kong / South Africa)
DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
M : (USA / Korea / Philippines) (option)
Press the E button to select Storage from. Select the beginning programme
with the F / G button or NUMBER buttons on the Storage from menu.
I
4.
PAL B/G, SECAM B/G
:
Auto programme
Manual programme
button to select Auto programme.
3. Press the G button to select System. Select a TV system with the F / G button;
L
: SECAM L/L' (option)
G
button and then D
use D
SCREEN
/ Ireland /
PIP/DW
Menu
Prev.
number
5. Press the E button to select Start.
6. Press the G button to
All receivable stations
Note
a.
In
begin
are
auto
programming.
stored.
:
some
models, the station
name
is stored for stations which broadcast VPS
(Video
Programme Service), PDC (Programme Delivery Control) or TELETEXT data. If no station name can be assigned to a station, the channel number is assigned and stored as
C (V/UHF 01-69) or S (Cable 01-47), followed by a number.
b. In Australia, if no station name can be assigned to a station, the channel number is
followed by a number see 'Assigning a station name' secassigned and stored as
tion to assign the station name.
-----
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit
screen.
Manual
-
See the
'Programme
menu
appears
on
the
edit' section to edit the stored programme.
Programme Tuning
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you
assign a station name with five characters to each programme number.
1. Press the MENU button and then
2. Press the G button and then D
use D
/
E
button to select the STATION
menu.
STATION
button to select Manual programme.
3. Press the G button to select Storage. Select the desired programme number with the
button
F / G
or
NUMBER buttons
4. Press the E button to select
L
SECAM L/L'
BG
:
I
:
DK
:
M
:
on
the
Storage
System. Select
a
/Australia)
PAL I/II (U.K.
Programme
Storage
2
System
BG
G
edit
Favourite programme
Band
/ G
button;
TIME
Fine
SPECIAL
Search
Name
(Europe
/ East
Europe
/ Asia / New Zealand / M.East / Africa
SCREEN
PIP/DW
/ Ireland /
Hong Kong /
PAL D/K, SECAM D/K (East Europe
(USA / Korea / Philippines) (option)
South
V/UHF
SOUND
menu.
TV system with the F
1
C01
Booster
Menu
Off
Prev.
Africa)
/ China / Africa /
5. Press the E button to select Band. Press the F
as
PICTURE
Auto programme
Manual programme
Channel
(option)
PAL B/G, SECAM B/G
:
/ E
can
/ G
CIS)
button to select V/UHF
or
Cable
required.
6. Press the E button to select Channel. You
the F
/ G
button
or
NUMBER buttons. If
can
possible,
select the desired channel number with
select the channel number
directly with
the number buttons.
7. Press the E button to select Search. Press the F
/ G
button to
commence
searching.
If
station is found the search will stop.
8. Press the OK button to store it.
a
9. To store another
station, repeat steps
3 to 8.
Owner's Manual
19
Operation
Channel
Channel Menu
Fine
-
Options
Options
Tuning
Normally
fine
tuning
is
only
necessary if
is poor.
reception
the 'Manual programme tuning' steps 1 to 2.
2. Press the G button and then D / E button to select Fine.
1.
Repeat
STATION
PICTURE
3. Press the F
/ G
button to fine tune for the best
picture
and sound.
tuned programme will be indicated
finely
by
a
yellow
Programme
edit
Favourite programme
SOUND
4. Press the OK button.
The
Auto programme
Manual programme
number
during
programme
Name
viewing.
STATION
PICTURE
3. Press the G button to
display
4. Press the D button. You
the Name
can use a
blank,
menu.
+,
-,
the
alphabet
A to Z and the numeric 0 to
Programme
edit
SOUND
Off
E
button you
can
select in the
position by pressing
opposite
direction.
2
System
BG
Band
sec-
V/UHF
1
Fine
Search
Name
the G button and then make your choice of the
C01
SCREEN
Booster
PIP/DW
7. Press the EXIT button to return to normal TV
Storage
Channel
SPECIAL
ond character, and so on.
6. Press the OK button in twice.
Off
Prev.
viewing.
(option)
models, Booster is
reception
is poor at the
optional function. Only a set with Booster can perform
fringe area of TV signal, select Booster to On.
an
the 'Manual programme tuning' steps 1 to 2.
2. Press the G button and then D / E button to select Booster.
1.
Auto programme
Manual programme
TIME
5. Select the next
If the
C01
Store
Favourite programme
9.
some
1
Booster
the 'Manual programme tuning' steps 1 to 2.
2. Press the G button and then D / E button to select Name.
In
V/UHF
SCREEN
Repeat
Booster
Band
Station Name
a
With the
BG
Search
PIP/DW
1.
System
Fine
SPECIAL
5. Press the EXIT button to return to normal TV
Assigning
2
Channel
TIME
selection.
Storage
Repeat
this function.
STATION
PICTURE
3. Press the F
/ G
button to select On
or
Off.
Programme
edit
Favourite programme
SOUND
4. Press the OK button.
5. Press the EXIT button to return to normal TV
Auto programme
Manual programme
viewing.
TIME
Storage
2
System
BG
Band
V/UHF
Channel
1
Fine
Search
SPECIAL
Name
C01
SCREEN
Booster
PIP/DW
20
PLASMA TV
Store
FG
Off
Operation
Programme
-
Edit
This function enables you to delete or skip the stored programmes. Also you can move
gramme numbers or copy a blank station data into the selected programme number.
1. Press the MENU button and then
button to select the STATION
2. Press the G button and then D / E button to select Programme edit.
3. Press the G button to display the Programme edit menu.
Deleting
use D / E
some
stations to other pro-
menu.
Programme
0-
a
programme
1. Select a programme to be deleted with the D / E or F / G button.
2. Press the RED button twice.
The selected programme is deleted, all the following programmes
are
shifted up
1.
2.
3.
4.
-
5C05
-
6C07
2C01
7C55
3C04
8S27
4C05
9S29
Delete
Copy
Move
Skip
Menu
Prev.
a
programme
1. Select a programme to be copied with the D / E or
2. Press the GREEN button.
All the following programmes are shifted down one
Moving
-
1BLN2
one
position.
Copying
-
edit
F / G
button.
position.
a
programme
Select a programme to be moved with the D / E or F / G button.
Press the YELLOW button.
Move the programme to the desired programme number with the D
Press the YELLOW button again to release this function.
/ E or F / G
button.
programme number
1. Select a programme number to be skipped with the D / E or F / G button.
2. Press the BLUE button. The skipped programme turns to blue.
3. Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be unable to select it using
the PR D / E button during normal TV viewing. If you want to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in
the programme edit or table menu.
Skipping
Favourite
-
a
Programme
This function lets you select your favourite programmes
1. Press the MENU button and then
2.
3.
4.
5.
6.
7.
8.
/ E button to select the STATION menu.
Press the G button and then D / E button to select Favourite programme.
Press the G button to display the Favourite programme menu.
Press the D / E button to select
Select a desired programme with the F / G button or NUMBER buttons. Any number
under 10 is entered with a numeric '0' (or '00') in front of it, i.e. '05' (or '005') for 5.
To store another programme, repeat steps 4 to 5.
You can store up to 8 programmes.
Press the OK button.
Press the EXIT button to return to normal TV viewing.
use D
--
-----
.
Repeatedly
Calling
-
directly.
You
Auto programme
Manual programme
Programme
PICTURE
0BLN2
edit
Favourite programme
---
--
---
---
--
---
---
--
---
---
--
---
---
--
---
---
--
---
---
--
---
G
SOUND
TIME
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
press the FAVOURITE button to select stored favorite programmes.
up the
can
STATION
Programme
Table
check the programmes stored in the memory
programme table
Press the LIST button to display the Programme table
The programme table appears on the screen.
by displaying
the programme table.
Displaying
?
?
menu.
You may find some blue highlighted programmes shown. They have been set up in the
programme edit mode.
Some programmes with the channel number shown in the programme table indicate
there is no station name assigned.
0-
-
-
-
5C05
-
1BLN2
6C07
2C01
7C55
3C04
8S27
4C05
9S29
programme in the programme table
Select a programme with the D / E or F / G button.
Then press the OK button.
The Plasma Display switches to the chosen programme number.
Selecting
a
programme table
There are 10 programme table pages in which contain 100 programmes.
Pressing the D / E or F / G button repeatedly turns the pages.
Paging through
a
Press the LIST button to return to normal TV
viewing.
Owner's Manual
21
Operation
Picture Menu
PSM
-
-
Options
Options
(Picture Status Memory)
This function
adjusts the set to the best picture appearance.
When adjusting picture options (contrast, brightness, colour, sharpness
is automatically changed to User.
and tint
(NTSC input only)) manually,
PSM
1. Press the PSM button
?
Each press of the PSM button
Intelligent Eye
?
?
?
You
the
screen
display
as
shown below.
Standard
Dynamic
Mild
User
also select Intelligent Eye, Dynamic, Standard, Mild or User in the PICTURE menu.
Picture options Intelligent Eye, Dynamic, Standard and Mild are preset and programmed for good
can
picture quality at the factory and cannot be changed.
When the Intelligent eye function is on, the most suitable picture
the surrounding conditions.
CSM
-
changes
is
automatically adjusted according
to
(Colour Status Memory)
To initialize values
(reset
to default
settings),
1. Press the MENU button and then
select the Normal
use D / E
option.
button to select the PICTURE
menu.
STATION
PSM
CSM
2. Press the G button and then
use D / E
PICTURE
button to select CSM.
use D / E
button to select the desired colour tempera-
TIME
ture.
4. Press the EXIT button to return to normal TV
Each press of D /
?
E
button
Cool
You
can
the
viewing.
screen
display
as
shown below.
Warm
Normal
Manual Colour
-
changes
Normal
Contrast
Brightness
60
Colour
50
Sharpness
50
adjust red,
green,
or
0
SPECIAL
Green
0
SCREEN
Blue
0
PIP/DW
Menu
Prev.
User
blue to any colour temperature you
2. Press the G button and then
use D / E
prefer.
button to select the PICTURE
menu.
STATION
use D / E
PSM
3. Press the G button and then
use D / E
button to select User.
use D / E / F / G
5. Press the EXIT button to return to normal TV
button to make
appropriate adjustments.
viewing.
You can enjoy the vivid and hi-definition picture with LG's Excellent
It's not available to use this function in RGB[PC], HDMI[PC] mode.
selecting picture options (Intelligent Eye, Dynamic,
matically changed to On.
1. Press the MENU button and then
use D / E
Normal
Digital Reality
Standard and
button to select the PICTURE
processor
Mild)
menu.
Contrast
Warm
100
Brightness
60
Colour
50
Sharpness
50
User
Red
0
SPECIAL
Green
0
SCREEN
Blue
0
PIP/DW
When
Cool
ACM
TIME
4. Press the G button and then
G
PICTURE
button to select CSM.
SOUND
-
User
Red
CSM
-
Warm
100
Temperature Control
1. Press the MENU button and then
-
Cool
ACM
SOUND
3. Press the G button and then
G
Menu
Prev.
technology.
in PICTURE menu, XD is auto-
STATION
PSM
CSM
2. Press the
G
button and then
use D / E
button to select XD.
use D / E
button to select On
or
Off.
TIME
4. Press the EXIT button to return to normal TV
viewing.
Contrast
60
Colour
50
Sharpness
50
SCREEN
22
PLASMA TV
100
Brightness
SPECIAL
PIP/DW
Menu
On
Off
ACM
SOUND
3. Press the G button and then
G
PICTURE
Prev.
Operation
sRGB
-
-
When the set
was
connected to external
equipment
the equal image each other.
This function works in the following mode
1. Press the MENU button and then
:
with sRGB function, It's
adjusted
a
colour difference to
display
RGB[PC], HDMI[PC].
use D / E
button to select the PICTURE
menu.
STATION
PSM
CSM
2. Press the G button and then
use D / E
PICTURE
button to select sRGB.
sRGB
SOUND
3. Press the G button and then
use D / E
button to select On
or
Off.
G
Contrast
Brightness
On
Off
100
60
TIME
4. Press the EXIT button to return to normal TV
viewing.
SPECIAL
SCREEN
PIP/DW
ACM
-
-
Menu
Prev.
(Active Colour Management)
the ACM to select the desired skin colour
This function works in the following mode:
Adjust
option.
TV, AV1, AV2, COMPONENT1/2, RGB[DTV], HDMI[DTV].
-
It's not available to
use
this function in XD Off mode.
1. Press the MENU button and then
use D / E
button to select the PICTURE
menu.
STATION
PSM
CSM
2. Press the G button and then
3. Press the G button and then
use D / E
use F / G
PICTURE
button to select ACM.
button to make
ACM
SOUND
appropriate adjustments.
TIME
4. Press the EXIT button to return to normal TV
viewing.
G
Contrast
100
Brightness
60
Colour
50
Sharpness
50
Fleshtone
0
Greentone
0
Bluetone
0
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
Manual Picture Control
-
-
-
You
adjust picture contrast, brightness, colour, sharpness and tint (NTSC input only)
It's not available to use colour, sharpness function in RGB[PC], HDMI[PC] mode.
In the broadcasting system PAL/SECAM, the picture item Tint doesn't work.
can
1. Press the MENU button and then
use D / E
button to select the PICTURE
menu.
to the levels you
STATION
prefer.
PSM
CSM
2. Press the G button and then
3. Press the G button and then
use D / E
use F / G
button to select the desired
button to make
picture option.
PICTURE
ACM
SOUND
appropriate adjustments.
TIME
4. Press the EXIT button to return to normal TV
viewing.
Contrast
100
Brightness
60
Colour
50
Sharpness
50
G
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
Owner's Manual
23
Operation
Sound
Sound Menu
SSM
-
-
Options
Options
(Sound Status Memory)
This function lets you enjoy the best sound without any special adjustment because the set automatically selects the
appropriate sound option based on the program content.
When adjusting sound options (treble and bass) manually, SSM is automatically changed to User.
1. Press the SSM button.
2. Press the SSM button to select your desired sound.
SRS TSXT
Flat
Music
Movie
User
Sports
You can also select SRS TSXT, Flat, Music, Movie, Sports or User in the SOUND menu.
The sound SRS TSXT, Flat, Music, Movie and Sports are programmed for good sound reproduction at the
and cannot be changed.
?
?
factory
R
-
TruSurround XT
-
is
a
trademark of SRS Labs, Inc.
TruSurround XT
technology
is
incorporated
under license from SRS Labs, Inc.
BBE
-
BBE
High
Definition Sound restores
1. Press the MENU button and then
clarity
and presence for better
speech intelligibility
button to select the SOUND
use D / E
menu.
and musical realism.
STATION
SSM
BBE
2. Press the
G
button and then
use D / E
PICTURE
button to select BBE.
use D / E
button to select On
or
Off.
TIME
4. Press the EXIT button to return to normal TV
viewing.
0
Treble
50
Bass
50
TV
On
Off
AVL
Balance
SOUND
3. Press the G button and then
G
Speaker
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
Manufactured under license from BBE Sound, Inc.
AVL
-
(Auto
Volume
Leveler)
This feature maintains
an
equal
volume level;
1. Press the MENU button and then
even
if you
change
channels.
button to select the SOUND
use D / E
menu.
STATION
SSM
BBE
2. Press the
G
button and then
use D / E
PICTURE
button to select AVL.
use D / E
button to select On
or
Off.
TIME
4. Press the EXIT button to return to normal TV
G
Balance
SOUND
3. Press the G button and then
AVL
viewing.
0
Treble
50
Bass
50
TV
Speaker
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
Adjusting Sound Control
1. Press the MENU button and then
use D / E
button to select the SOUND
menu.
STATION
SSM
BBE
2. Press the G button and then
use D / E
button to select the desired sound item.
PICTURE
Balance
SOUND
3. Press the G button and then
use F / G
button to make
4. Press the EXIT button to return to normal TV
appropriate adjustments.
viewing.
AVL
Treble
Bass
TIME
TV
24
:
Treble, Bass
PLASMA TV
or
BBE aren't suitable to
use
SRS TSXT.
Speaker
SPECIAL
PIP/DW
Menu
50G
50
SCREEN
Note
0
Prev.
On
Off
Operation
TV
-
-
Speaker
You
In COMPONENT
no
-
internal
adjust
can
video
speaker
1/2, RGB[PC]
status.
and
HDMI[PC] mode,
TV
speaker/variable
audio
be output
can
even
though
there is
signal.
If you want to
your external hi-fi stereo system, turn off the internal
use
1. Press the MENU button and then
use D / E
speakers
button to select the SOUND
of the set.
menu.
STATION
SSM
BBE
2. Press the
G
button and then
use D / E
PICTURE
button to select TV Speaker.
Balance
SOUND
3. Press the G button and then
use D / E
button to select On
or
Off.
TIME
4. Press the EXIT button to return to normal TV
AVL
0
Treble
50
Bass
50
TV
Speaker
GOn
Off
viewing.
SPECIAL
SCREEN
PIP/DW
Stereo / Dual
-
When
tion
a
Menu
Prev.
Reception
programme is selected, the sound information for the station appears after the programme number and sta-
disappear.
name
On Screen
Display
Press the I/II button to received broadcast state.
Broadcast
On
Mono
MONO
Stereo
STEREO
Dual
DUAL I
screen
Display
Mono Sound Selection
In stereo
if the stereo
signal is weak, you can switch to mono by pressing the
I/II button twice. In mono reception the depth of sound is improved. To switch back to
stereo, press the I/II button twice again.
reception
Language Selection
for Dual
Language Broadcast
If a programme received in two languages (dual language), you
DUAL II or DUAL I + II by pressing the I/II button repeatedly.
-
switch to DUAL I,
primary broadcast language to the loudspeakers.
II sends the secondary broadcast language to the loudspeakers.
I + II sends a separate language to each loudspeaker.
?
DUAL I
?
DUAL
?
DUAL
NICAM
can
sends the
Reception (option)
If your Plasma Display is equipped with the PDP Tuner for NICAM reception, the
Instantaneous Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the type of received broadcast
pressing the I/II button repeatedly.
?
?
When NICAM
(Near
by
mono
is weak, switch to FM mono.
When NICAM dual is received, you can select NICAM DUAL I, NICAM DUAL II,
NICAM DUAL I + II, or MONO. When FM mono is selected the display MONO
appears
Sound
signal
on
the
screen.
output selection
In AV,
Component, RGB or HDMI mode, you
loudspeakers.
Repeatedly press the I/II button to select the
?
follows
NICAM
is received, you can select NICAM MONO or FM MONO.
When NICAM stereo is received, you can select NICAM STEREO or FM MONO. If
the stereo
?
as
high quality
L+R
:
Audio
audio R
?
L+L
:
Audio
?
R+R
:
Audio
can
select output sound for the left and
right
sound output.
signal from audio L input is sent to left loud-speaker and audio signal
input is sent to right loud-speaker.
signal from audio L input is sent to left and right loud-speakers.
signal from audio R input is sent to left and right loud-speakers.
from
Owner's Manual
25
Operation
T ime Menu
Setting
-
Options
Options
the Clock
If current time
setting
is erased
by
a
power failure
1. Press the MENU button and then
use D
the set is
or
unplugged,
/ E button to select the TIME
reset the clock.
menu.
STATION
Clock
G
--
:
--
Off time
2. Press the G button and then
use D
/
E
PICTURE
button to select Clock.
On time
Auto
sleep
SOUND
3. Press the G button and then
4. Press the G button and then
use D
use D
/ E button to
adjust
the hour.
/ E button to
adjust
the minute.
5. Press the EXIT button to return to normal TV
TIME
SPECIAL
viewing.
SCREEN
PIP/DW
Setting
-
-
-
Prev.
Menu
the On/Off Timer
Timer function operates only if current time has been
Off Timer function overrides on Timer function if they
The set must be in
standby
already
are
set.
set to the
same
time.
mode for the On Timer to work.
1. Press the MENU button and then
use D
/ E button to select the TIME
menu.
STATION
Clock
Off time
G
2. Press the
3. Press the
G
button and then
button and then
/
use D
E
button to select Off time
or
/ E button to
adjust
the hour.
5. Press the G button and then
use D
/ E button to
adjust
the minute.
G
On time function; Press the
gramme number or volume level.
Only
button and then
7. Press the EXIT button to return to normal TV
-
To cancel
Auto
a
G
sleep
On
Off
12
Volume
SPECIAL
Programme
SCREEN
/ E button to
adjust
PIP/DW
pro-
Menu
Prev.
viewing.
Off/On
button has been
automatically
no
input signal,
switch back to
standby
mode
pressed.
the monitor turn off
1. Press the MENU button and then
use D
automatically
after 10 minutes.
/ E button to select the TIME
menu.
STATION
Clock
Off time
2. Press the G button and then
use D
/
E
PICTURE
button to select Auto sleep.
On time
Auto
sleep
use D
/ E button to select On
4. Press the EXIT button to return to normal TV
or
Off.
TIME
viewing.
SPECIAL
SCREEN
PIP/DW
Sleep
timer turns the set off at the preset time.
Press the SLEEP button to select the number of minutes. The
-
lowed
by 10, 20, 30, 60, 90, 120,
180 and 240 minutes. The
display
timer begins
zz
Min will appear
remaining sleep time, press the SLEEP button once.
b. To cancel the sleep time, repeatedly press the SLEEP button until the display
c. If you turn the set off after setting the sleep timer, the setting will be erased.
26
Prev.
the screen, folto count down from the number of minutes
---
on
selected.
a.
Menu
Timer
Sleep
-
To check the
PLASMA TV
zz
---
Min appears.
GOn
Off
SOUND
3. Press the G button and then
:
TIME
Sleep
If there is
-
use D
time function
Press the D / E button to select Off in step 3.
Two hours after the set is switched on by the on time function it will
unless
Auto
/ E button to select On.
use D
use D
-
On time.
On time
SOUND
4. Press the G button and then
6.
PICTURE
00
30
1
Operation
Menu
Special
Special
Options
Options
Child Lock
The set
-
be set up
can
so
that it
can
only
be used with the remote control.
1. Press the MENU button and then D / E button to select the SPECIAL
menu.
STATION
Language
Child lock
2. Press the G button and then D / E button to select Child lock.
3. Press the G button and then D / E button to select On
PICTURE
Off
ISM Method
Low power
SOUND
or
GOn
Set ID
Off.
Demo
TIME
4. Press the EXIT button to return to normal TV
viewing.
SPECIAL
SCREEN
PIP/DW
Prev.
This set programmed to remember which option it was last set to even if you turn the set off.
In Child lock 'On', if the set is turned off, press the INPUT, PR D / E button on the set or POWER, INPUT, MULTIMEDIA, PR D / E or NUMBER buttons on the remote control.
-
-
With the Child lock On, the display
pressed while viewing the set.
-
ISM
-
Menu
'
Child lock on' appears
the
screen
if any button
on
the front
panel
is
Method
(Image Sticking Minimization)
Frozen still
picture from a PC/video game displayed
image remaining even when you change the image.
a long period of time.
1. Press the MENU button and then
on
use D / E
the screen for prolonged periods will result in an ghost
Avoid allowing a fixed image to remain on the set's screen for
on
button to select the SPECIAL
menu.
STATION
Language
Child lock
PICTURE
2. Press the G button and then D
/ E
button to select ISM Method.
SOUND
ISM Method
Orbiter
or
button to select either Normal, White wash,
Inversion. If you unnecessary to set this function, set Normal.
/ E
Normal
Low power
White wash
Set ID
Orbiter
Demo
3. Press the G button and then D
G
Inversion
TIME
SPECIAL
SCREEN
?
White Wash
White Wash
:
permanent images from the screen.
Note: An excessive permanent image may be impossible to clear entirely with White
removes
PIP/DW
Menu
Prev.
Wash.
?
Orbiter
:
Orbiter may help prevent ghost images. However, it is best not to allow any fixed
image to remain on the screen. To avoid a permanent image on the screen, the
screen
?
will
move
Inversion
every 2 minutes.
:
This is the function to invert the
matically
panel
colour of the
screen.
The
panel
colour is auto-
inverted every 30 minutes.
4. Press the EXIT button to return to normal TV
viewing.
Owner's Manual
27
Operation
Special
Special
Menu
Options
Options
Low Power
-
This is the function to reduce the power
1. Press the MENU button and then
consumption
of the set.
button to select the SPECIAL
use D / E
menu.
STATION
Language
Child lock
2. Press the G button and then
3. Press the G button and then
button to select Low power.
use D / E
use D / E
button to select On
PICTURE
Low power
SOUND
or
ISM Method
Off.
GOn
Off
Set ID
Demo
TIME
4. Press the EXIT button to return to normal TV
viewing.
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
Demo
-
-
Use it to
see
the difference between XD demo
It's not available to
use
this function in
1. Press the MENU button and then
on
and XD Demo off.
RGB[PC], HDMI[PC]
use D / E
mode.
button to select the SPECIAL
menu.
STATION
Language
Child lock
2. Press the G button and then
3. Press the G button to
4. To
stop
XD
use D / E
button to select XD Demo.
PICTURE
Low power
SOUND
begin
ISM Method
Set ID
XD Demo.
Demo, press the EXIT button.
Demo
TIME
SPECIAL
SCREEN
PIP/DW
28
PLASMA TV
Menu
Prev.
G
To start
Operation
Screen
Screen Menu
Auto
-
-
Options
Options
Configure
Automatically adjusts picture position and
This function works in the following mode
1. Press the MENU button and then
minimizes
:
use D
image shaking.
RGB[PC].
button to select the SCREEN
/ E
menu.
STATION
Auto
config.
Manual
2. Press the G button and then
use D
button to select Auto
/ E
4. If
position
of the
image
is still not correct,
needs to be adjusted
the Manual Config..
picture
more
try
after Auto
-
-
-
-
on screen.
VGA Mode
Zoom +/-
TIME
adjustment again.
adjustment
in RGB
Cinema
NR
SPECIAL
(PC),
can
you
adjust
Reset
SCREEN
Prev.
Menu
viewing.
the image is still not correct, your set is functioning properly but needs further
The Auto config. functions don't need to be run for HDMI mode.
Although
Manual
config.
ARC
PIP/DW
5. Press the EXIT button to return to normal TV
-
Auto
To set
Position
?
If the
PICTURE
SOUND
3. Press the G button to start Auto config..
When Auto config. has finished, Ok will be shown
?
config..
G
adjustment.
Configure
If the
picture isn't
phase manually.
To correct the
clear after auto
screen
adjustment
and
especially
that characters
are
still
trembling, adjust
the
picture
size, adjust Clock.
This function works in the
following
mode
:
RGB[PC], RGB[DTV],
COMPONENT
(480p/576p/720p/1080i),
HDMI
(480p/576p/720p/1080i).
-
It's not available to
Phase, Clock function in RGB[DTV], COMPONENT (480p/576p/720p/1080i), HDMI
use
(480p/576p/720p/1080i)
mode.
1. Press the MENU button and then D / E button to select the SCREEN
2. Press the G button and then D / E button to select Manual
3. Press the
G
button and then D /
E
menu.
STATION
PICTURE
config..
button to select Phase, Clock, H-Position
SOUND
or
TIME
appropriate adjustments.
5. Press the EXIT button to return to normal TV
-
-
see a
Phase
0
Clock
0
H-Position
0
V-Position
0
VGA Mode
Zoom +/-
Cinema
NR
4. Press the F / G button to make
To
G
Position
SPECIAL
-
config.
Manual config.
ARC
V-Position.
Selecting
Auto
Reset
SCREEN
viewing.
PIP/DW
Menu
Prev.
Wide VGA/XGA mode
normal
picture,
match the resolution of RGB mode and selection of VGA/XGA mode.
In some models, it's not available to selection of XGA mode.
This function works in the following mode : RGB[PC].
1. Press the MENU button and then
2. Press the G button and then
3. Press the G button and then
use D / E
use D / E
button to select the SCREEN
button to select VGA Mode
(or
menu.
XGA
Mode).
STATION
Auto
PICTURE
VGA Mode
SOUND
use D / E
button to select the desired VGA/XGA resolution.
viewing.
G
640x480
ARC
848x480
Zoom +/-
852x480
Position
TIME
4. Press the EXIT button to return to normal TV
config.
Manual config.
Cinema
NR
SPECIAL
Reset
SCREEN
PIP/DW
Menu
Prev.
Owner's Manual
29
Operation
Screen
Screen Menu
Picture Format
Setting
-
You
Options
Options
can
watch the
screen
in various
picture formats; Spectacle,
Full
(option), Original, 4:3,
16:9
14:9 and
(Wide),
Zoom.
1. Press the MENU button and then
2. Press the G button and then
use D
3. Press the G button and then
Original, 4:3, 16:9,
14:9
or
use D
/
E
/ E button to select the SCREEN
menu.
button to select ARC.
STATION
Auto
PICTURE
VGA Mode
ARC
SOUND
use
/ E
D
button to select
Spectacle,
Full
(option),
Zoom.
TIME
SPECIAL
?
Spectacle
Full
signal,
screen
Position
Original
Cinema
4:3
NR
16:9
Reset
14:9
adjust
PIP/DW
Menu
Prev.
adjust
fully.
it will be
automatically changed
to the
4:3
selection will lead you to view
gray bars appearing at both the left and
picture with
right sides.
a
an
original
4:3
aspect ratio, with
16:9
(Wide)
Following selection
will lead you to adjust the picture horizontally, in
to fill the entire screen (useful for viewing 4:3 formatted DVDs).
?
Full
Original
Following
?
Zoom +/-
(option)
When your TV receives the wide
picture format to be sent.
?
Spectacle
SCREEN
When your TV receives the wide screen signal, following selection will lead you to
the picture horizontally or vertically, in a linear proportion, to fill the entire screen
?
G
Zoom
When your TV receives the wide screen signal, following selection will lead you to
the picture horizontally, in non-linear proportion, to fill the entire screen.
?
config.
Manual config.
a
linear
proportion,
14:9
You
can
enjoy
mode. The
the
screen
picture
format of 14:9
14:9 is viewed
just
TV programme through the 14:9
like that the screen 4:3 is magnified to the left /
or
general
right.
?
Zoom
selection will lead you to view the picture without any alternation, while filling
the entire screen. However, the top and bottom portions of the picture will be cropped.
Following
4. Press the EXIT button to return to normal TV
-
-
-
-
You
viewing.
only select 4:3 and 16:9 (Wide) in RGB[PC], HDMI[PC] mode only.
You can only select 4:3, 16:9 (Wide) and Zoom in RGB[DTV], HDMI[DTV], Component [DTV] mode only.
You can only select Spectacle, Full (option), 4:3, 16:9 (Wide), 14:9 and Zoom in Component [480i/576i]
There might be uncomfortable in full mode. Then change into other mode.
can
mode
only.
Picture Size Zoom
-
When
enlarging
or
reducing
the
picture,
the
screen
may be
display
unnatural
1. Press the MENU button and then D / E button to select the SCREEN
2. Press the G button and then D / E button to select Zoom
3. Press the
G
button and then
F
/ G
button to make
picture.
menu.
+/-.
appropriate adjustments.
STATION
Auto
PICTURE
VGA Mode
ARC
SOUND
viewing.
Zoom +/Position
TIME
4. Press the EXIT button to return to normal TV
config.
Manual config.
Cinema
NR
SPECIAL
Reset
SCREEN
PIP/DW
30
PLASMA TV
Menu
Prev.
100
G
F
%
G
Operation
Screen Position
You
-
are
available to this function after
Zoom In/Out.
adjusting
1. Press the MENU button and then D / E button to select the SCREEN
menu.
2. Press the G button and then D / E button to select Position.
3. Press the G button and then D / E
or F
/ G button to
adjust
STATION
Auto
PICTURE
VGA Mode
ARC
SOUND
the
position.
Zoom +/Position
D
G
F
G
E
TIME
4. Press the EXIT button to return to normal TV
config.
Manual config.
Cinema
NR
viewing.
SPECIAL
Reset
SCREEN
PIP/DW
Menu
Prev.
Cinema
-
-
When you watch the movie, this function adjusts the set to the best
This function works in the following mode:
TV, AV1, AV2
or
COMPONENT
appearance.
(480i/576i).
1. Press the MENU button and then
2. Press the G button and then
picture
button to select the SCREEN
use D / E
use D
menu.
/ E button to select Cinema.
STATION
Auto
PICTURE
VGA Mode
config.
Manual config.
ARC
3. Press the G button and then
use D
/ E button to select On
or
SOUND
Off.
Position
TIME
4. Press the EXIT button to return to normal TV
Zoom +/-
viewing.
Cinema
G
Off
NR
SPECIAL
On
Reset
SCREEN
PIP/DW
NR
-
Menu
Prev.
(Noise Reduction)
You
can
select 3D NR
or
MPEG NR to reduce the
picture
noise which may appear
on
the
screen
during watching
the TV.
-
-
This function is not available for
3D NR is not available for
use
in
in
RGB[PC[, HDMI[PC] mode.
RGB, HDMI, Component[DTV] mode.
use
1. Press the MENU button and then
2. Press the G button and then
3. Press the G button and then
use D / E
use D / E
use D / E
button to select the SCREEN
menu.
button to select NR.
STATION
Auto
PICTURE
VGA Mode
ARC
button to select 3D NR
or
MPEG NR.
SOUND
4. Press the
button to make
SPECIAL
viewing.
to
G
3D NR
0
MPEG NR
0
Reset
SCREEN
PIP/DW
Initializing (Reset
Cinema
NR
appropriate adjustments.
5. Press the EXIT button to return to normal TV
Zoom +/Position
TIME
F / G
config.
Manual config.
Menu
Prev.
original factory value)
This function operates in current mode.
To initialize the adjusted value
1. Press the MENU button and then D / E button to select the SCREEN
menu.
2. Press the G button and then D / E button to select Reset.
STATION
Auto
PICTURE
VGA Mode
ARC
SOUND
3. Press the G button.
You
PIP
can
initialize Phase, Clock, H-Position, V-Position, Position, Zoom +/-, PIP size,
position,
PIP
Transparency
Zoom +/Position
TIME
?
config.
Manual config.
and sub
picture
size of twin
picture.
Cinema
NR
SPECIAL
Reset
G
To set
SCREEN
PIP/DW
Menu
Prev.
Owner's Manual
31
Operation
PIP
-
-
(Picture-in-Picture)
(Picture-in-Picture)
PIP lets you view 2 different inputs (sources) on your set screen at the
It's not available to use this function in TELETEXT mode.
time.
same
PIP
Watching
Press the PIP button to show the sub
?
Feature
Each press of PIP button
changes
picture.
the
screen
display
as
shown below.
RGB
AV1
RGB
RGB
AV1
AV1
10:30
10:30
10:30
RGB
RGB
AV1
10:30
Note
10:30
:
When the sub
picture size is 1/2 of the main picture, the picture quality might get poor.
The motion of the sub picture can be unnatural because the set displays full screen by synchronizing the main picture
refresh rate between the main picture source and the sub picture source is different in PIP mode.
a.
b.
Programme Selection
Press the PIP PR
+
for Sub Picture
/- button to select
a
Moving
programme for the sub
picture.
the PIP
F / G
an
Input Signal Source
mode
only)
press the D /
E
or
button until desired
position is achieved. The sub picture
moves
or
up/down
left/right.
for the PIP
when the
Press the POSITION button.
Repeatedly
Selecting
(PIP
source
Win.
position
D
FG
E
Press the PIP INPUT button
to select the
the sub
In
input
picture.
source
RGB
for
AV1
10:30
Picture Size
models, when the
sub picture quality get poor
for sub picture, select Auto,
PAL, SECAM or NTSC in
some
PIP
System
Press the SIZE
then F
the sub
menu.
With
POP
(Picture-out-of-Picture:
Channel
Scan)
Use POP to search the programmes of all the memorized channels one-by-one on the 3 PIP screen display, (while the main
picture source remains the current channel).
the programmed channels are searched with
The
pictures
the 3 POP
of all
/ G button to
picture
SIZE
Adjusting
Transparency (PIP
mode
1. Press the MENU button and then D / E
PIP/DW menu.
ously.
/ E
3. Press the
only)
-
button to select the
button to select PIP
button and then F / G button to
adjust
PIP trans-
parency.
4. Press the EXIT button to return to normal TV
32
PLASMA TV
size.
button
in
DW1,
Win. size
F
G
With SIZE button in PIP
screen.
Transparency.
G
adjust
mode, sub picture is adjusted.
-
2. Press the G button and then D
and
DW2 modes, main and sub
picture is adjusted simultane-
Adjusting
PIP
button
viewing.
In TV
the
screen
for the PIP
picture and RGB[PC] for the
sub picture, you can use Auto config and Manual config to
adjust the screen of the sub picture.
In TV or AV modes for main picture and HDMI[DTV] or
Component 480p, 576p, 720p, 1080i for the sub picture, you
can use Manual config to adjust the screen of the sub picture.
or
AV modes for the main
Operation
eletext
Teletext
T
-
Teletext
TOP
(or
text)
(option)
(option)
is
an
optional function,
therefore
the set with the teletext system
only
can
receive the teletext
broadcast.
-
-
Teletext is
a
free service broadcast
by most TV stations which gives up-to-the-minute
prices and many other topics.
television programmes, share
The teletext decoder of this set
consists of
TEXT
can
information
on
news,
weather,
support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext)
number of pages which are selected by directly entering the corresponding page number. TOP and FASmore modern methods allowing quick and easy selection of teletext information.
are
a
Switch on/off
Press the TEXT/* button to switch to teletext.
The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time
?
are
displayed
on
the
screen
head-
line. The first page number indicates your selection, while the second shows the current
page displayed.
Press the TEXT/* button to switch off teletext.
SIMPLE Text
(option)
Page selection
1. Enter the desired page number
three
as a
digit
number with the NUMBER buttons. If
selection you press a wrong number, you must
and then reenter the correct page number.
during
2. The PR D / E button
Programming
a
can
also be used to select the
preceding
the three
or
digit
following
number
page.
colour button in LIST mode
If the TV is in SIMPLE text, TOP text
LIST mode.
or
FASTEXT mode, press the
Four teletext page numbers of your choice
pressing the corresponding coloured button
1. Press
complete
can
on
M
be colour coded and
button to switch to
easily
selected
by
the remote control handset.
coloured button.
a
the NUMBER buttons, select the page you wish to programme.
3. Press the OK button. The selected page is stored as the selected page number, blinking once to confirm this. From now on, you can select this page with the same coloured
2.
Using
button.
4. The three other coloured buttons
TOP Text
The
The
are
programmed
in this way.
(option)
guide displays four fields-red, green, yellow
yellow field denotes the next group and the blue
user
and blue at the bottom of the
screen.
field indicates the next block.
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the
yellow
button to
proceed
to the next group with automatic overflow to the next
block.
3. With the green button you
flow to the next
4. The red button
can
be
proceed to the next existing page with automatic overgroup. (Alternatively the PR D button can be used.)
permits to return to previous selection. (Alternatively the PR E button
can
used.)
Direct page selection
Corresponding to the SIMPLE text mode, you can select
digit number using the NUMBER buttons in TOP mode.
a
page
by entering
it
as a
three
Owner's Manual
33
Operation
FASTEXT
The teletext pages are colour coded along the bottom of the
pressing the corresponding coloured button.
screen
and
are
selected
by
Page selection
1. Press the
2. You
can
button to select the index page.
select the pages which are colour coded
i
the bottom line with the
along
same
coloured buttons.
3.
4.
Corresponding to the SIMPLE text mode, you can select a page by entering its three
digit page number with the NUMBER buttons in FASTEXT mode.
The PR D / E button can also be used to select the preceding or following page.
Special
Teletext Functions
REVEAL
Press this button to
concealed information, such
display
as
solutions of riddles
or
puzzles.
Press this button
again
to
remove
the information from the
display.
SIZE
Selects double
Press this
Press this
Press this
height text.
button to enlarge the top half of the page.
button again to enlarge the bottom half of the
button again to return to the normal display.
page.
UPDATE
Displays
the TV
picture
on
the
Press this button to view the
screen
updated
while
waiting
for the
new
teletext page.
teletext page.
HOLD
the automatic page
Stops
more
change
which will
if
occur
teletext page consists of 2
a
or
sub pages. The number of sub pages and the sub page
shown
on
the
screen
below the time. When this button is
is
displayed at the top
change is inhibited.
left-hand
To continue press this button
corner
of the
screen
displayed is, usually,
pressed the stop symbol
and the automatic page
again.
MIX
Displays
the teletext pages
To switch the TV
picture
superimposed
on
off press this button
the TV
picture.
again.
TIME
This button has two functions:
a) When viewing a TV programme, press this button to display the time at the top
right hand corner of the screen. Press this button again to remove the display.
b) In teletext mode, press this button to select a sub page number. The sub page
number is displayed at the bottom of the screen. To hold or change the sub page,
press the RED/ GREEN or PR D / E buttons. Press this button again to exit this
function.
34
PLASMA TV
Miscellaneous
External Control
Control Device
-
Connect the RS-232C
and control the set's
input jack to an external
functions externally.
How to connect external control
?
?
?
control device
(such
The set remote control and front
or
panel
controls
Back
panel
of the set
or an
A/V control
system)
(except
main
V DEO
O
jack
on
power)
the Monitor back
panel.
will not be functional if the Monitor is controlled
by
a
PC
>
V DEO
AUD
L
COMPONEN
RGB INPUT
AUDIO INPUT
DVI(VIDEO)
computer
other external device.
<
HDMI/
as a
equipment
Connect the serial port of the control device to the RS-232C
RS-232C connection cables are not supplied with the set.
computer
Setup
Setup
NPU
O
AUD
R
2
L
MON
OR
R
OU
PU
V
RS-232C INPUT
REMOTE
CONTROL
(CONTROL/SERVICE)
(MONO)
COMPONEN
Type
of connector; D-Sub
No.
Pin
1
No connection
2
RXD
3
TXD
4
DTR
5
GND
AV
NPU
1
SVDEO
male
1
name
6
DSR
7
RTS
5
(Receive data)
(Transmit data)
(DTE side ready)
9
(DCE side ready)
(Ready to send)
(Clear to send)
8
CTS
9
No Connection
RS-232C
9-pin
NPU
1
6
configurations
3-wire
configuration
(Not standard)
7-wire
configuration
(Standard RS-232C cable)
PC
PDP
PC
PDP
RXD
TXD
RXD
TXD
TXD
RXD
TXD
RXD
GND
GND
DSR
DTR
DTR
DSR
CTS
RTS
RTS
CTS
GND
DTR
DSR
RTS
CTS
2354678
D-Sub 9
3256487
D-Sub 9
2354678
D-Sub 9
3254678
GND
DTR
DSR
RTS
CTS
D-Sub 9
Owner's Manual
35
Miscellaneous
Set ID
-
-
Use this function to
specify a
Mapping
Refer to 'Real Data
set ID number.
1'. See page 40.
1. Press the MENU button and then
the D
use
button to select the SPECIAL
/ E
menu.
STATION
Language
Child lock
2. Press the G button and then
3. Press the G button and then
use D / E
use
button to select Set ID.
F / G button to
adjust
PICTURE
ISM Method
Low power
SOUND
Set ID to choose the desired
Set ID
G
1
Demo
TIME
monitor ID number.
SPECIAL
?
The
adjustment
range of Set ID is 1
~
99.
SCREEN
4. Press the EXIT button to return to normal TV
viewing.
PIP/DW
MENU Prev.
Communication Parameters
?
Baud rate
?
Data
9600
:
length
Parity : None
?
*
Use
:
a
bps (UART)
?Stopbit:1bit
8 bits
crossed
?
(reverse)
Communication code
:
ASCII code
cable.
Command Reference List
COMMAND 1
COMMAND 2
DATA
(Hexadecimal)
01. Power
k
a
0~1
Input Select
Aspect Ratio
k
b
0~6
k
c
Refertop.37
04. Screen Mute
k
d
0~1
02.
03.
05. Volume Mute
k
06. Volume Control
k
07. Contrast
k
e
f
0~1
Transmission /
Protocol
Receiving
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
*
[Command 1]
First command to control PDP set.
:
(jork)
*
*
[Command 2]
[Set ID]
:
Second command to control PDP set.
:
You
can
adjust
the set ID to choose
desired monitor ID number in
0~64
special
menu.
g
0~64
k
h
0~64
09. Colour
k
i
0~64
99.
Adjustment range is 1
When selecting Set ID '0', every
connected PDP set is controlled.
10. Tint
k
j
0~64
Set ID is indicated
11.
(option)
Sharpness
k
k
0~64
12. OSD Select
k
l
0~1
08.
Brightness
~
*
13. Remote control lock mode
k
m
0~1
14. PIP/DW
k
n
Refertop.38
15. PIP Position
k
q
0~3
16. Treble
k
r
0~64
17. Bass
k
s
0~64
18. Balance
k
t
0~64
19. Colour
k
u
0~3
20.
k
v
0~50
k
w
0~50
Temperature (CSM)
Red Adjustment
21. Green
Adjustment
Blue Adjustment
PIP input Source
k
[DATA]
To transmit command data.
:
Transmit 'FF' data to read status of
command.
*
[Cr]
Carriage
:
Return
ASCII code '0x0D'
*[]
ASCII code
:
'space (0x20)'
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
*
The Monitor transmits ACK
(acknowledgement)
$
0~50
k
y
0~6
24. Abnormal Status
k
z
0~a
25. ISM Method
j
j
j
j
j
j
p
0~3
q
0~1
r
1~FE
Error Acknowledgement
s
1~3
[Command2][ ][Set ID][ ][NG][Data][x]
t
0~20
22.
23.
26. Low Power
27. Orbiter Time
28. Orbiter Pixel
Setting
Setting
29. Picture Size
30. Auto
31.
32.
33.
34.
*
Configure
Programme selection
Key
Input select (Main)
Input select (PIP)
When
36
setting
the 23
PLASMA TV
m
a
m
c
x
x
32,
~
a menu
1
u
b
y
doesn't
0~63
Key Code
Refertop.41
Refertop.41
display
on screen.
decimal
(1~99)on
menu and as Hexa decimal (0x0~0x63)
on transmission/receiving protocol.
as
this format when
based
on
normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
receiving
computer.
*
The Monitor transmits ACK
(acknowledgement)
this format when
abnormal data from
receiving
non-viable functions
Data
1:
Illegal
2: not
or
communication
Code
support function
3: Wait
more
time
errors.
based
on
Miscellaneous
04. Screen Mute
(Command
G To control Power On/Off of the TV.
G To select
mute on/off.
Transmission
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
[k][d][ ][Set ID][ ][Data][Cr]
01. Power
Data
0
:
2
(Command
:
a)
Power Off
Data
:PowerOn
1
screen
0
:
Screen mute off
1
:
Screen mute
2
d)
:
(Picture on)
(Picture off)
on
Ack
Ack
[a][ ][Set ID][ ][OK][Data][x]
[d][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off.
Transmission
05. Volume Mute
(Command
[k][a][ ][Set ID][ ][FF][Cr]
G To control volume
mute on/off.
Ack
You
adjust
mute
the MUTE button
using
on
Transmission
In like manner, if other functions transmit '0xFF' data
based on this format, Acknowledgement data feed back
[k][e][ ][Set ID][ ][Data][Cr]
Data
status about each function.
presents
also
e)
:
remote control.
[a][ ][Set ID][ ][OK][Data][x]
*
can
2
0
:
Volume mute off
1
:
Volume mute
(Volume on)
(Volume off)
on
Ack
Input Select (Command
02.
G To select input
You
source
also select
can
SELECT button
on
an
2
[e][ ][Set ID][ ][OK][Data][x]
b)
:
for the TV.
input
source
using
the INPUT
the Monitor's remote control.
(Command
You
on
[k][b][ ][Set ID][ ][Data][Cr]
can
also
adjust
Transmission
:TV
4
:
1
:AV1
5
:RGB
[k][f][ ][Set ID][ ][Data][Cr]
2
:AV2
6
:HDMI
Data
3
:
Component2
Component1
Min:0~Max:64
*
Refer to 'Real data
mapping
Ack
[b][ ][Set ID][ ][OK][Data][x]
[f][ ][Set ID][ ][OK][Data][x]
07. Contrast
Ratio
G To adjust the
You
(Command
screen
2
Picture
Size)
(Main picture format)
screen format using the ARC
adjust the
(Aspect Ratio Control) button
SCREEN
c) (Main
format.
also
can
:
on
remote control
or
in the
menu.
G To adjust
You
1
:
Normal
2
:
Wide
3
:
Spectacle
4
:
Full
(4:3)
(16:9)
screen
screen
screen
6
:
Original
7
:
Wide
8
:
Full
screen
(14:9)
the PC
aspect ratio.
input,
g)
contrast.
adjust
contrast in the PICTURE
menu.
Min:0~Max:64
Refer to 'Real data
mapping
1'. See page 40.
(Zoom)
you select either 16:9
[g][ ][Set ID][ ][OK][Data][x]
(Option)
08.
Brightness (Command
G To adjust
[c][ ][Set ID][ ][OK][Data][x]
Using
also
:
Ack
Ack
*
screen
2
[k][g][ ][Set ID][ ][Data][Cr]
*
[k][c][ ][Set ID][ ][Data][Cr]
can
(Command
1'. See page 40.
Transmission
Data
Transmission
Data
f)
remote control.
0
Aspect
:
volume with the volume buttons
Ack
03.
2
G To adjust volume.
Transmission
Data
06. Volume Control
You
or
4:3
screen
can
2
brightness.
adjust brightness
:
h)
screen
also
in the PICTURE
menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
Refer to 'Real data
mapping
1'. See page 40.
Ack
[h][ ][Set ID][ ][OK][Data][x]
Owner's Manual
37
Miscellaneous
09. Colour
G To adjust the
You
can
2
(Command
also
screen
adjust
14.PIP/DW(Command2:n)
i)
:
G To control the PIP (Picture In picture)/DW.
colour.
colour in the PICTURE
You
menu.
also control the PIP/DW
can
the remote control
Transmission
or
in the PIP/DW
[k][i][ ][Set ID][ ][Data][Cr]
Transmission
Data
[k][n][ ][Set ID][ ][Data][Cr]
Min:0~Max:64
*
Refer to 'Real data
mapping
1'. See page 40.
Data
using
the PIP button
menu.
0: PIP/DW off
3: DW2
Ack
1: PIP
5: POP
[i][ ][Set ID][ ][OK][Data][x]
2: DW1
Ack
10. Tint
(Command
G To adjust the
You
can
also
screen
adjust
2
[n][ ][Set ID][ ][OK][Data][x]
j) (option)
:
tint.
tint in the PICTURE
menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
15. PIP Position
Data
G To select sub picture position for PIP.
Red:0~Green:64
*
Refer to 'Real data
mapping
1'. See page 40.
You
TION button
Ack
[j][ ][Set ID][ ][OK][Data][x]
11.
also
can
You
can
also
adjust
the sub
2
k)
:
sharpness.
adjust sharpness in
Data
screen
the PICTURE
menu.
down
0
:
Right
or
in the PIP/DW
POSImenu.
1
:
Left down
2
:
Left up
3
:
Right
on screen
on screen
on screen
up
on screen
[k][k][ ][Set ID][ ][Data][Cr]
Ack
Data
[q][ ][Set ID][ ][OK][Data][x]
Min:0~Max:64
Refer to 'Real data
picture position using
the remote control
on
q)
:
[k][q][ ][Set ID][ ][Data][Cr]
Transmission
*
2
Transmission
Sharpness (Command
G To adjust the
(Command
mapping
1'. See page 40.
Ack
[k][ ][Set ID][ ][OK][Data][x]
16. Treble
12. OSD Select
(Command
2
:
(Command
2
:r)
G To adjust treble.
l)
You
G To select OSD (On Screen Display) on/off when
can
also
adjust
treble in the SOUND
menu.
con-
Transmission
trolling remotely.
[k][r][ ][Set ID][ ][Data][Cr]
Transmission
Data
[k][l][ ][Set ID][ ][Data][Cr]
Data0
:OSDoff
Min:0~Max:64
*
1:OSDon
Refer to 'Real data
mapping
1'. See page 40.
Ack
Ack
[r][ ][Set ID][ ][OK][Data][x]
[l][ ][Set ID][ ][OK][Data][x]
13. Remote control lock mode
G
To lock the front
panel
controls
(Command
on
2
:
m)
the monitor and remote
control.
You
[k][m][ ][Set ID][ ][Data][Cr]
0
:
Lock off
1:Lockon
Data
the remote control, use this mode.
When main power is on/off, external control lock is
you're
not
using
released.
38
:
s)
PLASMA TV
can
also
adjust
bass in the SOUND
menu.
[k][s][ ][Set ID][ ][Data][Cr]
Min:0~Max:64
*
[m][ ][Set ID][ ][OK][Data][x]
If
2
Transmission
Ack
*
(Command
G To adjust bass.
Transmission
Data
17. Bass
Refer to 'Real data
mapping
Ack
[s][ ][Set ID][ ][OK][Data][x]
1'. See page 40.
on
Miscellaneous
18. Balance
(Command
2
:
G
G To adjust balance.
You
can
also
adjust
Input Select (Command
23. PIP
t)
balance in the SOUND
To select
input
source
ture mode. You
menu.
picture using
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data
[k][y][ ][Set ID][ ][Data][Cr]
*
Refer to 'Real data
mapping
1'. See page 40.
Data
Ack
[t][ ][Set ID][ ][OK][Data][x]
picture in PIP/DW picadjust input source for sub
PIP INPUT button
Transmission
Min:0~Max:64
y)
:
for sub
also
can
2
remote control.
on
0
:TV
4
:
1
:AV1
5
:RGB
2
:AV2
6
:HDMI
3
:
Component2
Component1
Ack
19. Colour
[y][ ][Set ID][ ][OK][Data][x]
2
Temperature (Command
:
u)
G To adjust colour temperature.
You
can
also
adjust
CSM in the PICTURE
menu.
Transmission
24. Abnormal State
[k][u][ ][Set ID][ ][Data][Cr]
G To recognize
Data
0: Cool
1: Normal
2: Warm
3: User
an
2
(Command
:
z)
abnormal state.
Transmission
Ack
[k][z][ ][Set ID][ ][FF][ ][Cr]
[u][ ][Set ID][ ][OK][Data][x]
Data
FF
Read
:
Ack
[z][ ][Set ID][ ][OK][Data][x]
20. Red
Adjustment (Command
2
v)
:
Data
0: Normal
1:
G To adjust red in colour temperature.
2:
Transmission
3:
[k][v][ ][Set ID][ ][Data][Cr]
4:
Data
5: 5V down
Min:0~Max:50
*
Refer to 'Real data
(Power on and signal exist)
No signal (Power on)
Turn the TV off by remote control
Turn the TV off by sleep time function
Turn the TV off by RS-232C function
6: AC down
mapping
2'. See page 40.
7: Turn the TV off
8: Turn the TV off
Ack
9: Turn the TV off
[v][ ][Set ID][ ][OK][Data][x]
a:
*
21. Green
Adjustment (Command
2
:
Turn the TV off
This function is "read
by
by
by
by
Fan Alarm function
(option)
Off time function
Auto
function
sleep
AV board detect
only".
w)
G To adjust green in colour temperature.
25. ISM Method
Transmission
(Command
[k][w][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:50
*
Refer to 'Real data
mapping
2'. See page 40.
Ack
1
j, Command
:
G To control the ISM method. You
Method in SPECIAL
2
:
p)
also
can
adjust
ISM
menu.
Transmission
[w][ ][Set ID][ ][OK][Data][x]
[j][p][ ][Set ID][ ][Data][Cr]
Data
22. Blue
Adjustment (Command
2
:
$)
G To adjust blue in colour temperature.
0
:
Normal Mode
2
:
Orbiter
1
:
White Wash
3
:
Inversion
Ack
[p][ ][Set ID][ ][OK][Data][x]
Transmission
[k][$][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:50
*
Refer to 'Real data
mapping
2'. See page 40.
Ack
[$][ ][Set ID][ ][OK][Data][x]
Owner's Manual
39
Miscellaneous
26. Low Power
(Command
30. Auto
1
:
j, Command
2
:
Configure
(Command 1 : j, Command
q)
G To reduce the power consumption of the TV. You
also
adjust
Low Power in SPECIAL
can
menu.
:Off
1
:On
u)
It works
only
in RGB
(PC)
mode.
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
[j][q][ ][Set ID][ ][Data][ ][Cr]
0
:
G To adjust picture position and minimize image shaking
automatically.
Transmission
Data
2
Data
1: To set
Ack
Ack
[u][ ][Set ID][ ][OK][Data][x]
[q][ ][Set ID][ ][OK][Data][x]
27. Orbiter Time
(Command
1
Setting
: j, Command
G To adjust orbiter operation time
31.
2
:
r)
G To select
term.
Min: 1
Data0
Max: FE
Refer to 'Real data
*
:
a)
picture.
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
[j][r][ ][Set ID][ ][Data][ ][Cr]
Data
programme for the main
a
2
Transmission
Transmission
~
Programme selection
(Command 1 : m, Command
mapping
Min:0~Max:63(0~C7,200Prison)
Refer to 'Real data mapping 1'.
*
1'.
Ack
Data1
Don't
Data2
0
:
care
Main
1:Sub
[r][ ][Set ID][ ][OK][Data][x]
Ack
[a][ ][Set ID][ ][OK][Data0][x]
28. Orbiter Pixel
(Command
1
Setting
: j, Command
2
:
s)
G To adjust pixel number in orbiter function.
Transmission
[j][s][ ][Set ID][ ][Data][Cr]
Data
Min:1~Max:3
Refer to 'Real data
*
mapping
1'.
*
Ack
Real data
0
mapping
1
:Step0
[s][ ][Set ID][ ][OK][Data][x]
*
Real data
0:-40
1:-39
A
:Step10(SetID10)
2:-38
F
:Step15(SetID15)
:Step16(SetID16)
28:0
10
4E:+38
29. Picture Size
Setting for DW Mode
(Command 1 : j, Command 2 : t)
64
:
Step
100
4F:+39
50:+40
G To select the DW picture format.
You
also select the DW
can
SIZE
on
picture
the remote control.
Transmission
[j][t][ ][Set ID][ ][Data][Cr]
Data
Min: 0
*
~
using
:
Step
110
73
:
115
74
:
Step
Step
C7
:
Step
199
FE
:
254
FF
:
Step
Step
the
Max: 20
Refer to 'Real data
mapping
Ack
[t][ ][Set ID][ ][OK][Data][x]
40
format
6E
PLASMA TV
1'.
116
255
mapping
2
Miscellaneous
32.
Key
(Command
G To send IR
34.
1
:
remote
m, Command 2
key
:
c)
code.
(Command
source
for sub
1
:
x, Command 2
picture
in PIP mode
code
-
Data
Structure
Refer to page 43.
MSB
[c][ ][Set ID][ ][OK][Data][x]
0
LSB
0000000
External
Input
External
Input
Input
Number
Data
0001
Analog
0010
AV
0100
Component
Transmission
0101
RGB-DTV
[x][b][ ][Set ID][ ][Data][Cr]
0110
RGB-PC
1001
HDMI
Input select (Command
(Main Picture Input)
G To select input
Data
source
1
:
x, Command 2
for TV
Structure
MSB
0
y)
[x][y][ ][Set ID][ ][Data][Cr]
Ack
33.
:
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
Key
select
G To adjust input
Transmission
Data
Input
:
b)
LSB
Input
0000000
External
External
Input
Input
Input
Data
Analog
0010
AV
0100
Component
0101
RGB-DTV
0110
RGB-PC
1001
HDMI
Number
Data
0000
Input1
0001
Input2
Number
0001
Input
Number
Ack
[y][ ][Set ID][ ][OK][Data][x]
Data
0000
Input1
0001
Input2
Ack
[b][ ][Set ID][ ][OK][Data][x]
Owner's Manual
41
Miscellaneous
IR Code
Code
(NEC
(NEC Format)
How to connect
G
Connect your wired remote control to the Remote Control port
Remote Control IR Code
on
the Monitor.
(NEC Format)
G Output waveform
Single pulse,
modulated with 37.917KHz
at 455KHz
signal
TC
Carrier
frequency
FCAR
1/TC
Duty
T1
=
ratio
=
=
fOSC/12
T1/TC
1/3
=
G Configuration of frame
?
1st frame
Lead
Low
High
code
custom code
custom code
Data code
Data code
C0 C1C2C3C4C5C6C7C0C1C2C3C4C5C6C7D0D1D2D3D4D5D6D7D0D1D2D3D4D5D6D7
?
Repeat
frame
Repeat
code
Tf
G Lead code
9ms
4.5
ms
0.55
G Repeat code
ms
9ms
2.25
ms
G Bit description
?
Bit "0"
?
0.56
0.56
ms
1.12
G Frame interval
:
Bit "1"
2.24
ms
Tf
The waveform is transmitted
as
long
as a
key
is
depressed.
Tf
Tf
Tf=108ms
42
PLASMA TV
ms
@455KHz
ms
Miscellaneous
Code
Function
(Hexa)
Note
00
PR+
R/C Button
01
PR-
R/C Button
02
VOL+
R/C Button
03
VOL-
R/C Button
40
D
R/C Button
41
E
R/C Button
06
G
R/C Button
07
F
R/C Button
08
POWER
R/C Button
C4
POWER ON
Discrete IR
C5
POWER OFF
Discrete IR
09
MUTE
R/C Button
10
Number
11
Number
12
Number
13
Number
14
Number
15
Number
16
Number
17
Number
18
Number
19
Number
0B
INPUT
R/C Button
98
MULTIMEDIA
R/C Button
BF
COMPONENT1
Discrete IR Code
D4
COMPONENT2
Discrete IR Code
C6
HDMI
Discrete IR Code
D5
RGB
Discrete IR Code
D6
TV
Discrete IR Code
5A
AV1
Discrete IR Code
D0
AV2
Discrete IR Code
1E
FAVOURITE
R/C Button
1A
Q.VIEW
R/C Button
0A
I/II
R/C Button
0E
SLEEP
R/C Button
43
MENU
R/C Button
44
OK(
4D
PSM
R/C Button
52
SSM
R/C Button
53
LIST
R/C Button
20
TEXT/*
R/C Button
2A
REVEAL
R/C Button
22
MODE
R/C Button
24
MIX
R/C Button
26
TIME
R/C Button
62
UPDATE / WIN.POSITION
R/C Button
64
SIZE / WIN.SIZE
R/C Button
65
HOLD
R/C Button
70
INDEX
R/C Button
60
PIP/DW
R/C Button
61
PIP INPUT
R/C Button
63
SWAP
R/C Button
71
PIP PR+
R/C Button
72
PIP PR-
R/C Button
5C
Zoom
R/C Button
5D
Zoom
79
ARC
76
ARC
77
ARC
AF
ARC
Key
Key
Key
Key
Key
Key
Key
Key
Key
Key
0
R/C Button
1
R/C Button
2
R/C Button
3
R/C Button
4
R/C Button
5
R/C Button
6
R/C Button
7
R/C Button
8
R/C Button
9
R/C Button
)
+
-
(Power On/Off)
Code (Only Power On)
Code (Only Power Off)
(Input
(Input
(Input
(Input
(Input
(Input
(Input
COMPONENT1
COMPONENT2
Selection)
Selection)
HDMI
Selection)
RGB Selection)
TV Selection)
AV1 Selection)
AV2 Selection)
R/C Button
R/C Button
R/C Button
(4:3)
(16:9)
(Zoom)
Discrete IR Code
Discrete IR Code
Discrete IR Code
(Only
(Only
(Only
4:3
mode)
16:9 mode)
Zoom mode)
Owner's Manual
43
Miscellaneous
Programming
G
The remote is
a
multi-brand
or a
the Remote
universal remote. It
can
be
programmed
to
operate
most remote-controllable devices of
other manufacturers.
Note that the remote may not control all models of other brands.
Programming
a
a
code
code into
a
a
1. To find out whether your remote
remote mode
can
operate the device without programming,
turn
on
the device such
as a
VCR and
press the corresponding mode button on the remote.
After that, press the POWER button. If the device is turned off then it
be
programmed.
explained below.
If not, the remote should be
2. Press the MENU and MUTE button
programmed
continuously
at the
to
same
responds properly and the remote need not to
operate the device. The programming procedures are
time for 2 seconds, the current selected device button
will be illuminated.
If you don't press any button for 20 seconds, the
repeat from step 2.
3. Enter code numbers
pressing
the
using the number button
button, the light blinks at a time.
on
44
PLASMA TV
see
if the device
on
the mode button will be turned off. In that case, you have to
the remote
by referring
the code table
If the device turned off, the
4. Press the MENU button to store the code. After
5. Test the remote functions to
light
blinking twice,
on
programming
the
is successful.
this code is stored.
responds properly.
following
If not, repeat from step 2.
pages. When
Miscellaneous
Programming
Codes
Codes
VCRs
VCRs
Brand
Codes
Brand
Codes
AIWA
034
KENWOOD
014
034
AKAI
016
043
047
048
125
146
001
012
013
020
101
106
114
123
046
124
LG
AMPRO
072
ANAM
031
033
103
AUDIO DYNAMICS
012
023
039
BROKSONIC
035
037
129
CANON
028
031
033
CAPEHART
108
CRAIG
003
040
135
CURTIS MATHES
031
033
041
DAEWOO
005
007
010
064
065
108
110
111
112
116
117
119
043
(GOLDSTAR)
039
043
Brand
Codes
PORTLAND
108
TATUNG
039
043
PULSAR
072
TEAC
034
039
043
QUARTZ
QUASAR
011
014
TECHNICS
031
033
070
033
066
075
145
TEKNIKA
019
031
033
034
RCA
013
020
033
034
034
LXI
003
009
013
014
040
041
062
063
THOMAS
034
017
034
101
106
107
109
140
144
TMK
006
145
147
TOSHIBA
008
013
042
047
003
008
010
014
059
082
112
131
031
033
034
040
TOTEVISION
040
101
053
054
101
UNITECH
040
MAGIN
040
MAGNAVOX
031
033
067
068
012
031
MARANTZ
034
033
041
REALISTIC
067
RICO
058
VECTOR RESEARCH
012
MARTA
101
RUNCO
148
VICTOR
048
MATSUI
027
030
SALORA
014
VIDEO CONCEPTS
012
MEI
031
033
SAMSUNG
032
040
102
104
VIDEOSONIC
040
MEMOREX
003
010
014
031
105
107
109
112
WARDS
033
034
053
072
113
115
120
122
101
102
134
139
125
059
DBX
012
023
DYNATECH
034
053
ELECTROHOME
059
EMERSON
006
017
025
027
MGA
045
046
029
031
034
035
MINOLTA
013
020
036
037
046
101
MITSUBISHI
013
020
045
046
129
131
138
153
049
051
059
061
FISHER
003
008
009
010
151
FUNAI
034
GE
031
033
063
107
109
144
GO VIDEO
132
136
HARMAN KARDON
012
045
HITACHI
004
018
026
043
063
137
INSTANTREPLAY
031
033
JCL
031
033
JCPENNY
012
013
015
040
066
101
034
040
072
MULTITECH
024
034
147
NEC
012
023
039
034
OPTONICA
053
054
150
PANASONIC
066
070
074
133
140
145
013
020
031
JVC
012
031
033
043
048
050
055
060
130
150
152
013
017
024
031
033
034
040
053
054
131
043
048
135
YAMAHA
012
034
039
SANYO
003
007
010
014
ZENITH
034
048
056
102
134
058
072
080
101
017
037
112
129
003
008
009
010
013
014
017
020
031
042
073
081
054
149
008
009
SCOTT
043
043
101
043
043
003
022
SEARS
NORDMENDE
033
046
SANSUI
048
PENTAX
034
131
MTC
JENSEN
101
069
108
043
Codes
LLOYD
DAYTRON
039
Brand
083
031
034
067
PHILIPS
031
033
034
067
071
101
PILOT
101
PIONEER
013
Brand
Codes
GOLDEN CHANNEL
030
HAMLIN
049
050
021
031
SHINTOM
024
SONY
003
009
031
052
056
057
058
076
077
078
149
033
034
033
063
PHILCO
SHARP
054
SOUNDESIGN
034
STS
013
SYLVANIA
031
059
067
048
SYMPHONIC
034
TANDY
010
Brand
Codes
034
CATV
CATV
Brand
Codes
ABC
003
004
039
046
052
053
042
Brand
Codes
SPRUCER
047
078
STARCOM
002
004
076
STARGATE
008
030
POST NEWS WEEK
016
TADIRAN
030
TAEKWANG
110
TAIHAN
105
TANDY
017
PIONEER
055
065
085
090
034
051
052
AJIN
112
HITACHI
052
055
ANTRONIK
014
HOSPITALITY
070
077
ARCHER
005
JERROLD
002
003
004
008
PRUCER
059
CABLE STAR
026
009
010
052
069
PTS
011
048
CENTURION
092
074
073
074
CENTURY
007
LG
CITIZEN
007
M-NET
COLOUR VOICE
065
090
COMBANO
080
COMTRONICS
019
DIAMOND
023
EAGLE
020
030
040
EASTERN
057
062
066
ELECTRICORD
032
OAK
016
031
GE
072
PANASONIC
044
047
GEMINI
008
022
PARAGON
100
GI
052
074
PHILIPS
006
007
014
024
071
063
072
PULSAR
100
TEXSCAN
029
037
RCA
047
TOCOM
039
MACOM
033
REGAL
049
TOSHIBA
100
081
MAGNAVOX
010
REGENCY
057
UNIKA
030
MEMOREX
100
REMBRANT
025
MOVIE TIME
028
032
SAMSUNG
102
107
030
068
NSC
015
028
SCIENTIFIC ATLANTA
003
011
041
042
043
045
046
025
(GOLDSTAR)
001
106
012
101
064
038
005
079
071
073
054
012
037
013
053
020
SHERITECH
022
SIGNAL
030
SIGNATURE
052
SL MARX
030
050
040
056
007
014
024
UNITED CABLE
004
053
UNIVERSAL
005
007
014
024
026
027
032
035
012
015
018
086
087
088
089
100
114
060
VIEWSTAR
ZENITH
Owner's Manual
093
45
Miscellaneous
Programming
Codes
Codes
HDSTB
Brand
Codes
ALPHASTAR DSR
Brand
Codes
Brand
Codes
123
133
134
PACE SKY SATELLITE
143
AMPLICA
050
GENERAL INSTRUMENT 003
004
016
PANASONIC
060
BIRDVIEW
051
126
129
031
059
101
PANSAT
121
CHANNEL MASTER
013
014
015
HITACHI
139
140
036
055
HOUSTON TRACKER
033
037
CHAPARRAL
008
009
057
104
CITOH
054
CURTIS MATHES
050
145
DRAKE
005
006
007
011
052
112
012
018
077
029
PERSONAL CABLE
039
051
080
086
PRESIDENT
019
102
101
135
136
PRIMESTAR
030
110
RCA
066
106
LEGEND
057
REALISTIC
043
074
123
024
046
056
076
LG
001
SAMSUNG
ECHOSTAR
038
040
057
058
LUTRON
132
SATELLITE SERVICE CO 028
093
094
095
096
LUXOR
062
144
097
098
099
100
MACOM
010
059
SONY
103
STARCAST
041
SUPER GUIDE
020
124
125
TEECOM
023
026
075
Brand
Codes
069
070
Brand
Codes
VIEWSTAR
115
WINEGARD
128
146
ZENITH
081
082
091
120
083
084
066
092
057
085
065
NORSAT
027
047
032
017
022
035
111
SCIENTIFIC ATLANTA
FUJITSU
043
079
108
124
042
078
KATHREIN
028
025
105
116
NEXTWAVE
016
PICO
072
114
UNIDEN
049
PROSAT
EUROPLUS
127
048
061
057
002
045
JERROLD
MEMOREX
TOSHIBA
044
010
089
130
071
060
ELECTRO HOME
107
PHILIPS
JANIEL
122
090
137
117
DX ANTENNA
021
142
068
141
Codes
088
HUGHES
147
Brand
063
064
125
138
087
Audio
Brand
Codes
AIWA
014
028
070
096
JVC
004
013
141
PHILIPS
026
112
143
125
129
139
229
KEC
185
186
187
PIONEER
039
042
043
063
TOSHIBA
137
KENWOOD
038
050
067
089
065
091
093
094
THE
061
170
171
197
206
115
123
127
250
VICTOR
088
215
222
230
AKAI
163
ANAM
003
014
017
023
059
106
189
216
217
235
236
Brand
147
QUASAR
113
WARDS
089
RCA
080
YAMAHA
054
RCX
092
KOHEL
030
NAD
045
046
LOTTE
014
016
036
098
REALISTIC
103
106
SAMSUNG
124
145
146
182
252
CARVER
086
100
172
173
174
CLARION
199
175
176
177
178
193
194
195
203
DAEWOO
027
053
060
084
179
180
181
183
204
244
245
246
102
148
198
221
201
202
208
213
SANSUI
011
135
138
144
DENON
015
075
130
143
214
219
223
232
SANYO
019
083
234
FANTASIA
071
238
240
SCOTT
106
186
FINEARTS
022
SHARP
031
032
051
052
FISHER
089
099
072
082
117
119
LG(GOLDSTAR)
001
021
024
029
199
200
087
107
108
190
191
192
211
212
239
HAITAI
034
035
188
HARMAN/KARDON
068
INKEL
037
058
062
078
079
122
LXI
103
MAGNAVOX
111
MARANTZ
002
018
020
025
156
184
110
034
041
081
090
206
209
210
097
112
SHERWOOD
005
006
158
SONY
044
045
109
114
118
126
248
249
012
020
073
074
076
077
105
161
MCINTOSH
049
MCS
104
MEMOREX
107
069
NAD
046
095
121
ONKYO
013
040
041
047
162
163
164
165
149
150
151
048
056
057
132
166
167
168
169
152
153
154
155
133
140
205
231
233
242
157
158
159
160
OPTIMUS
158
189
207
222
224
PANASONIC
007
033
064
113
010
085
106
136
225
226
227
243
142
220
241
251
185
187
237
113
128
TAEKWANG
TEAC
218
131
055
199
BURMECTER
222
Codes
247
PENNEY
104
TECHNICS
101
Brand
Codes
Brand
Codes
Brand
Codes
Brand
Codes
APEX DIGITAL
022
MAGNAVOX
013
PHILIPS
013
SONY
007
DENON
020
014
MARANTZ
024
PIONEER
004
THOMPSON
005
006
GE
005
006
MITSUBISHI
002
PROCEED
021
TOSHIBA
019
008
HARMAN KARDON 027
NAD
023
PROSCAN
005
006
YAMAHA
009
018
JVC
012
ONKYO
008
017
RCA
005
006
ZENITH
010
016
LG
001
PANASONIC
003
009
SAMSUNG
011
015
134
DVD
46
PLASMA TV
010
016
025
026
025
Miscellaneous
Notes
Owner's Manual
47
Miscellaneous
Notes
48
PLASMA TV
Miscellaneous
Notes
Owner's Manual
49
Miscellaneous
Checklist
T
Checklist
roubleshooting
Troubleshooting
No
picture
&
?
Check whether the set is turned
?
Power cord inserted into wall outlet?
on.
No sound
?
Picture OK &
Plug
another
cord
was
product's
plugged in.
power cord into the wall outlet where the set's power
?
Press the VOLUME
?
Sound muted? Press MUTE button.
?
Check whether the TV
?
Check to
(G)
button.
No sound
causing
?
The remote control
doesn't work
?
Check to
see
(Refer
p.6)
or
Poor colour
Poor
?
This is normal
?
?
or
new
batteries.
as
the
(Refer
to
one
of the
?
speakers
?
Unusual sound from
inside the set
PLASMA TV
polarities.
p.6)
image
is muted
Keep
to
a
menu
and press the VOLUME
A
picture
is
on
the
screen
for
Balance in the SOUND
change
in ambient
at the time of
the set.
after five
button.
certain distance between the set and the VCR.
Check for local interference such
Adjust
(G)
the set.
p.23)
Activate any function to restore the
still
during the startup process of
the picture has not appeared
brightness
more
as an
of the
menu.
picture.
than 5 minutes, the
screen
electrical
or
picture shaking
No output from
50
installed with the correct
are
Select Colour in the PICTURE
(If
?
menu.
between the set and the remote control
object
Please contact your service centre, if
minutes.
picture
Horizontal/vertical bars
is "on" in the SOUND
Check if the remote control handset is set up to correct mode.
(Refer
or
to
if the batteries
Install
?
No
if there is any
obstruction.
see
?
Picture appears slowly,
after switching on
speaker
(Refer
to
appliance
gets dark.)
power tool.
p.24)
humidity or temperature may result in an unusual noise
switching off or on of the set and does not indicate a fault with
Miscellaneous
Product
Specifications
Specifications
42PX4RV
42PX4RVA
42PX4RVH
42PX4RV-TA
42PX4RVA-TA
42PX4RVH-TA
MODEL
Width
(inches
/
mm)
49.3 / 1252
Height (inches
/
mm)
27.78 / 705.5
Depth (inches
/
mm)
11.29 / 286.7
/
70.06 / 31.78
Weight (pounds
Power
kg)
requirement
AC100-240V, 50/60Hz
Operating Temperature Range
32
Operating Humidity Range
~
104°F
(0
40°C)
~
Less than 80%
50PX4R
50PX4RH
50PX4R-TA
50PX4RH-TA
MODEL
Width
(inches
/
mm)
55.1 / 1400
Height (inches
/
mm)
32.3 / 821
Depth (inches
/
mm)
3.9/99
Weight (pounds
Power
/
115 / 52.15
kg)
requirement
AC100-240V, 50/60Hz
32
Operating Temperature Range
The
specifications
shown above may be
104°F
(0
40°C)
~
Less than 80%
Operating Humidity Range
?
~
changed
without notice for
quality improvement.
Owner's Manual
51
Download PDF