LG | 42PJ350R | LG 60PK550R Owner’s Manual

OWNER’S MANUAL
PLASMA TV
Please read this manual carefully before operating
your set and retain it for future reference.
www.lg.com
TV
Ferrite Core
(Gray)
(This feature is
available only
42PJ**** models.)
SOCKET
Ferrite core can be used to reduce RF noise when
connecting the RF cable.
The closer the location of the ferrite core to the
“ANTENNA IN”, the better it is.
The ferrite core can be used to
reduce the electromagnetic waves in
the PC Audio cable.
Ferrite Core Wind the PC Audio cable on the ferrite core twice, and then plug the
(Gray)
cables into the TV as shown in the
(This feature is not following picture.
available for all Place the ferrite core close to AUDIO
IN(RGB/DVI) jack on the display.
models.)
Ferrite Core
(Black)
(This feature is not
available for all
models.)
Ferrite core can be used to
reduce the electromagnetic
wave when connecting the
power cord.
The closer the location of the
ferrite core to the power plug,
the better it is.
Place the ferrite core close to
AUDIO IN(RGB/DVI) jack on the display.
HDMI, the HDMI logo and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing LLC.
Install the power
plug closely.
CONTENTS
PREPARATION
PLASMA TV Models : 42/50PJ2***, 42/50PJ3***,
42/50PJ5***, 42/50PJ6***, 50/60PK5*** ......... A-1
Antenna Connection.............................................1
Connecting with a Component cable...................2
Connecting with an HDMI cable..........................3
Connecting with an HDMI to DVI cable...............4
USB setup. .............................................................. 4
Connecting with a RCA cable..............................5
Connecting with a RF Cable................................6
External Stereo Setup..........................................6
Connecting with a D-sub 15 pin cable.................7
Supported Display Resolution..............................8
Screen Setup for PC mode..................................9
WATCHING TV / PROGRAMME CONTROL
Turning on the TV..............................................13
Initializing Setup ................................................13
Programme Selection.........................................13
Volume Adjustment............................................13
Quick Menu........................................................14
On Screen Menus Selection and Adjustment....15
Auto Programme Tuning . .................................16
Manual Programme Tuning................................17
Programme Edit ................................................19
Selecting the Programme List............................21
Favourite Programme Setup..............................22
Input List.............................................................23
Input Label.........................................................24
SIMPLINK...........................................................25
AV Mode.............................................................28
Initializing (Reset to Original Factory Settings)....29
Key Lock............................................................30
When Connecting a USB Device.......................31
Photo List...........................................................33
Music List...........................................................39
Movie List...........................................................42
DivX Registration Code......................................48
Deactivation........................................................49
CONTENTS
EXTERNAL EQUIPMENT SETUP
TO USE A USB DEVICE
PICTURE CONTROL
Picture Size (Aspect Ratio) Control...................50
Energy Saving....................................................52
Preset Picture Settings......................................53
Manual Picture Adjustment................................54
Picture Improvement Technology.......................55
Advanced - Black(Darkness) Level....................56
Advanced - Film Mode.......................................57
Picture Reset......................................................58
Image Sticking Minimization (ISM) Method.......59
Demo Mode........................................................60
Mode Setting......................................................61
SOUND & LANGUAGE CONTROL
Auto Volume Leveler..........................................62
Clear Voice II......................................................63
Preset Sound Settings-Sound Mode.................64
Sound Setting Adjustment -User Mode.............65
Infinite Sound.....................................................65
Balance..............................................................66
TV Speakers On/ Off Setup...............................67
Audio Reset........................................................68
I/II
Stereo/Dual Reception (In Analogue Mode Only)...69
NICAM Reception..............................................70
Speaker Sound Output Selection......................70
On-Screen Menu Language Selection..............71
I
CONTENTS
TIME SETTING
CONTENTS
Clock Setup........................................................72
Auto On/Off Time Setting...................................73
Sleep Timer Setting............................................74
TELETEXT
Switch On/Off ....................................................75
SIMPLE Text......................................................75
TOP Text............................................................75
FASTEXT...........................................................76
Special Teletext Functions.................................76
APPENDIX
Troubleshooting..................................................77
Maintenance.......................................................79
Product Specifications ......................................80
IR Codes............................................................83
External Control Device Setup...........................84
II
PREPARATION
PLASMA TV Models : 42/50PJ2***, 42/50PJ3***, 42/50PJ5***,
42/50PJ6***, 50/60PK5***.
ACCESSORIES
or
Owner’s Manual
x3
Batteries
(AAA)
Power Cord
Remote Control
x2
x4
M5X14 M4X28
Bolts for stand assembly
(Except for 60PK5***)
PREPARATION
Ensure that the following accessories are included with your TV. If an accessory is missing, please
contact the dealer where you purchased the TV.
■ Here shown may differ from your TV.
Protection Cover
This item is not included for all models.
Wall Mounting Bracket(Separate purchase)
AW-50PG60M
Polishing Cloth
Polishing cloth for use on the screen.
* Lightly wipe any stains or fingerprints on
the surface of the TV with the polishing
cloth.
Do not use excessive force. This may
cause scratching or discolouration.
Tie Band
(Only 42PJ****)
Cable Holder
AW-50PG60MS
or
(Except for 60PK5***)
AW-60PG60MS
AW-60PG60M
or
(Only 60PK5***)
A-1
PREPARATION
!
FRONT
PANEL CONTROLS
! NOTE
energy consumed during use can be significantly reduced if the level of brightness of the picture is
?►►The
reduced, and this will reduce the overall running cost.
PREPARATION
?
CAUTION
►►Do not step on the glass stand or subject it to any impact.
It may break, causing possible injury from fragments of glass, or the TV may fall.
►►Do not drag the TV. The floor or the product may be damaged.
42/50PJ2***
■ Image shown may differ from your TV.
POWER INPUT
Touch Sensor
• You can use the desired
button function by
touching.
MENU
OK
VOLUME
PROGRAMME
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to the
surrounding conditions.
Power/Standby Indicator
• Illuminates red in standby mode.
• The LED is off while the TV remains on.
A-2
42/50PJ3***
■ Image shown may differ from your TV.
PREPARATION
POWER INPUT
Touch Sensor
• You can use the desired
button function by
touching.
MENU
OK
VOLUME
PROGRAMME
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to the
surrounding conditions.
Power/Standby Indicator
• Illuminates red in standby mode.
• The LED is off while the TV remains on.
A-3
PREPARATION
■ Image shown may differ from your TV.
42/50PJ5***
50/60PK5***
PREPARATION
SPEAKER
POWER INPUT
MENU
OK
VOLUME
PROGRAMME
Touch Sensor
• You can use the desired
button function by
touching.
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to the
surrounding conditions.
Power/Standby Indicator
• Illuminates red in standby mode.
• The LED is off while the TV remains on.
A-4
42/50PJ6***
■ Image shown may differ from your TV.
PREPARATION
POWER INPUT
MENU
OK
VOLUME
PROGRAMME
Touch Sensor
• You can use the desired
button function by
touching.
Intelligent Sensor
Adjusts picture according to the surrounding
conditions.
Remote Control Sensor
Power/Standby Indicator
• Illuminates red in standby mode.
• The LED is off while the TV remains on.
A-5
PREPARATION
BACK PANEL INFORMATION
■ Image shown may differ from your TV.
42/50PJ3***, 42/50PJ5***, 42/50PJ6***, 50/60PK5***
10
PREPARATION
2
1
7
2
5
6
7
1
Power Cord Socket
This TV operates on an AC power. The voltage is
indicated on the Specifications page. Never
attempt to operate the TV on DC power.
2
HDMI Input
Connect an HDMI signal to HDMI IN.
Or DVI(VIDEO)signal to HDMI/DVI port with DVI
to HDMI cable.
RGB/DVI Audio Input
Connect the audio from a PC.
3
A-6
4
3
4
Component Input
Connect a component video/audio device to these
jacks.
5
RS-232C Input (CONTROL&SERVICE) Port
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.
6
RGB Input
Connect the output from a PC.
8
9
7
Audio/Video Input (AV IN1/2)
Connect audio/video output from an external
device to these jacks.
8
Variable Audio Output
Connect an external amplifier or add a subwoofer
to your surround sound system.
9
Antenna Input
Connect RF antenna to this jack.
10
USB Input
Connect USB storage device to this jack.
BACK PANEL INFORMATION
■ Image shown may differ from your TV.
42/50PJ2***
8
1
5
PREPARATION
2
3
2
4
5
1
Power Cord Socket
This TV operates on an AC power. The voltage is
indicated on the Specifications page. Never
attempt to operate the TV on DC power.
2
HDMI Input
Connect an HDMI signal to HDMI IN.
Or DVI(VIDEO)signal to HDMI/DVI port with DVI
to HDMI cable.
3
Component Input
Connect a component video/audio device to these
jacks.
4
RS-232C Input (CONTROL&SERVICE) Port
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.
5
Audio/Video Input (AV IN1/2)
Connect audio/video output from an external
device to these jacks.
6
7
6
Variable Audio Output
Connect an external amplifier or add a subwoofer
to your surround sound system.
7
Antenna Input
Connect RF antenna to this jack.
8
SERVICE ONLY PORT
A-7
PREPARATION
STAND INSTALLATION
■ Image shown may differ from your TV.
■ When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the
product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can
deviate from abrasion of the tightening part of the bolt.
PREPARATION
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Assemble the parts of the Stand Body with the
Stand Base of the TV.
Stand Body
M5X14
Stand Base
3
4
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the
back of the TV.
M4X28
A-8
CAREFUL INSTALLATION ADVICE
1
1
2
2
1
Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen then bolts.)
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
2
Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the
wall.
PREPARATION
■ You should purchase necessary components to fix the TV safety and secure to the wall from the
market.
■ Position the TV close to the wall to avoid the possibility of it falling when pushed.
■ The instructions shown below are a safer way to set up the TV, by fixing it to the wall, avoiding the
possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing
injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the
TV.
3
3
Use a sturdy rope to tie the product for alignment. It is safer to tie the rope so it becomes horizontal between
the wall and the product.
! NOTE
►►When moving the TV undo the cords first.
►►Use a platform or cabinet strong and large enough to support the size and weight of the TV.
►
?►To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
A-9
PREPARATION
BACK COVER FOR WIRE ARRANGEMENT
■ Image shown may differ from your TV.
After Connecting the cables as necessary, install Cable Holder as shown and bundle the cables.
PREPARATION
Cable Holder
SWIVEL STAND
■ This feature is not available for all models.
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to
suit your viewing position.
A-10
NOT USING THE DESK-TYPE STAND
■■ Image shown may differ from your TV.
When installing the wall-mounted unit,use the protection cover. Insert the Protection cover into the TV
until clicking sound.
PREPARATION
Protection Cover
(Fixate the unit so that the guide is on the outer side.)
EARTHING
Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not
possible, have a qualified electrician install a separate circuit breaker.
Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.
Power Supply
Circuit breaker
A-11
PREPARATION
■ The TV can be installed in various ways such as on a wall, or on a desktop etc.
■ The TV is designed to be mounted horizontally.
DESKTOP PEDESTAL INSTALLATION
For adequate ventilation allow a clearande of 10 cm (4 Inches) all around the TV.
PREPARATION
10 cm
10 cm
10 cm
10 cm
WALL MOUNT : HORIZONTAL INSTALLATION
■■ We recommend the use of a LG Brand wall mounting bracket when mounting the TV to a wall.
■■ We recommend that you purchase a wall mounting bracket which supports VESA standard.
■■ LG recommends that wall mounting be performed by a qualified professional installer.
A
B
! NOTE
►►Should Install wall mount on a solid wall perpendicular to the floor.
►►Should use a special wall mount, if you want to
? install it to ceiling or slanted wall.
►►The surface that wall mount is to be mounted on
should be of sufficient strength to support the weight
of TV set; e.g. concrete, natural rock, brick and hollow block.
►►Installing screw type and length depends on the wall
mount used. Further information, refer to the instructions included with the mount.
►►LG is not liable for any accidents or damage to property or TV due to incorrect installation:
- Where a non-compliant VESA wall mount
is used.
- I Incorrect fastening of screws to surface
which may cause TV to fall and cause
personal injury
- Not following the recommended Installation
method.
10 cm
10 cm
10 cm
10 cm
10 cm
A-12
Model
42PJ2***
50PJ2***
42PJ3***
50PJ3***
42PJ5***
50PJ5***
42PJ6***
50PJ6***
50PK5***
60PK5***
VESA
(A * B)
400 * 400
400 * 400
400 * 400
400 * 400
400 * 400
400 * 400
400 * 400
400 * 400
400 * 400
600 * 400
Standard Quantity
Screw
M6
M6
M6
M6
M6
M6
M6
M6
M6
M8
4
4
4
4
4
4
4
4
4
4
REMOTE CONTROL KEY FUNCTION
Only 42/50PJ2***
When using the remote control, aim it at the remote control sensor on the TV.
ENERGY Adjust the power saving mode of the TV.
SAVING
AV MODE It helps you select and set images and sounds
when connecting AV devices.( p.28)
PREPARATION
POWER Switches the TV on from standby or off to standby.
INPUT External input mode rotate in regular sequence.
Switches the TV on from standby.
TV Selects TV channel.
0 to 9 number Selects a programme.
button Selects numbered items in a menu.
LIST Displays the programme table.
Q.VIEW Returns to the previously viewed programme.
VOLUME UP Adjusts the volume. /DOWN
FAV Displays the selected favourite programme.
RATIO Selects your desired picture format.
MUTE Switches the sound on or off.
Programme Selects a programme.
UP/DOWN
PAGE UP/ Move from one full set of screen information to the
DOWN next one.
Coloured These buttons are used for teletext (on TELETEXT
buttons models only), Programme edit.
TELETEXT These buttons are used for teletext.
BUTTONS For further details, see the ‘Teletext’ section.( p.75)
A-13
PREPARATION
MENU Selects a menu.
Clears all on-screen displays and returns to TV viewing from any menu.
CLEAR VOICE II It helps users listen to human voices better.
PREPARATION
Q. MENU Select the desired quick menu source.( p.14)
BACK Allows the user to move return one step in an interactive application, EPG or other user interaction
function.
EXIT Clears all on-screen displays and return to TV viewing from any menu.
See a list of AV devices connected to TV.
When you toggle this button, the Simplink menu
appears at the screen.( p.25)
THUMBSTICK A
llows you to navigate the on-screen menus and
(Up/Down/Left/Right) adjust the system settings to your preference.
OK Accepts your selection or displays the current
mode.
SIMPLINK / Controls SIMPLINK menu.
USB Menu
control buttons
FREEZE Pause the present picture at the screen. (It doesn't
work at USB Mode.)
The TV returns to normal viewing automatically if
no signal is received or no operation is performed
for 5 minutes.
Installing Batteries
■ Open the battery compartment cover on the back and install
the batteries matching correct polarity (+with +,-with -).
■ Install two 1.5 V AAA batteries. Do not mix old or used batteries
with new ones.
■ Close cover.
■ To remove the batteries, perform the installation a actions in
reverse
A-14
REMOTE CONTROL KEY FUNCTION
Except 42/50PJ2***
When using the remote control, aim it at the remote control sensor on the TV.
POWER Switches the TV on from standby or off to standby.
AV MODE It helps you select and set images and sounds
when connecting AV devices.( p.28)
INPUT External input mode rotate in regular sequence.
Switches the TV on from standby.
PREPARATION
ENERGY Adjust the power saving mode of the TV.
SAVING
TV Selects TV channel.
0 to 9 number Selects a programme.
button Selects numbered items in a menu.
LIST Displays the programme table.
Q.VIEW Returns to the previously viewed programme.
VOLUME UP Adjusts the volume.
/DOWN
MARK Check and un-check programmes in the USB
menu.(Except for 42/50PJ2***)
FAV Displays the selected favourite programme.
RATIO Selects your desired picture format. MUTE Switches the sound on or off.
PAGE UP/ Move from one full set of screen information to the
DOWN next one.
Programme Selects a programme.
UP/DOWN
Coloured These buttons are used for teletext (on TELETEXT
buttons models only), Programme edit.
TELETEXT These buttons are used for teletext.
BUTTONS For further details, see the ‘Teletext’ section.( p.75)
A-15
PREPARATION
MENU Selects a menu.
Clears all on-screen displays and returns to TV viewing from any menu.
Controls the USB menu.
PREPARATION
Q. MENU Select the desired quick menu source.( p.14)
BACK Allows the user to move return one step in an interactive application, EPG or other user interaction
function.
EXIT Clears all on-screen displays and returns to TV viewing from any menu.
See a list of AV devices connected to TV.
When you toggle this button, the Simplink menu
appears at the screen.( p.25)
THUMBSTICK Allows you to navigate the on-screen menus and
(Up/Down/Left/ adjust the system settings to your preference.
Right)
OK Accepts your selection or displays the current mode.
SIMPLINK / Controls SIMPLINK or USB menu. (Except for
USB Menu 42/50PJ2***)
control buttons
FREEZE Pause the present picture at the screen. (It doesn't
work at USB, Simplink Mode.)
The TV returns to normal viewing automatically if
no signal is received or no operation is performed
for 5 minutes.
Installing Batteries
■ Open the battery compartment cover on the back and install
the batteries matching correct polarity (+with +,-with -).
■ Install two 1.5 V AAA batteries. Do not mix old or used batteries
with new ones.
■ Close cover.
■ To remove the batteries, perform the installation a actions in
reverse
A-16
EXTERNAL EQUIPMENT SETUP
■■ To prevent damage do not connect to the mains outlet until all connections are made between the
devices.
ANTENNA CONNECTION
■■ For optimum picture quality, adjust antenna direction.
■■ An antenna cable and converter are not supplied.
Outdoor
Antenna
(VHF, UHF)
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
RF Coaxial Wire (75 Ω)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
EXTERNAL EQUIPMENT SETUP
Wall
Antenna
Socket
UHF
Antenna
Signal
Amplifier
VHF
■■ In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier
to the antenna as shown above.
■■ If signal needs to be split for two TVs, use an antenna signal splitter for connection.
1
EXTERNAL EQUIPMENT SETUP
■ To avoid damaging any equipment, never plug in any power cord until you have finished connecting
all equipment.
■ This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 42/50PJ3*** models.
■ Image shown may differ from your TV.
CONNECTIING WITH A COMPONENT CABLE
EXTERNAL EQUIPMENT SETUP
1
Connect the video outputs (Y, PB, PR) of the
external equipment (digital set-top box, DVD,
etc.) to the COMPONENT IN VIDEO jacks on
the TV.
2
Connect the audio outputs (Y, PB, PR) of the
external equipment (digital set-top box, DVD,
etc.) to the COMPONENT IN AUDIO jacks on
the TV.
3
Turn on the external equipment.
(Refer to the external equipment's manual for
operating instructions.)
4
Select COMPONENT 1 input source using the
INPUT button on the remote control.
If connected to COMPONENT IN 2, select
COMPONENT 2 input source.
1
2
Signal
Component
HDMI
480i/576i
O
X
480p/576p
O
O
720p/1080i
O
O
1080p
O
O
(50/60Hz only)
(24Hz/30Hz/50Hz/60Hz)
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
2
Component ports on the TV
Y
PB
PR
Video output ports
on DVD player
Y
Y
Y
Y
PB
B-Y
Cb
Pb
PR
R-Y
Cr
Pr
CONNECTING WITH AN HDMI CABLE
Connect the HDMI output of the external equipment (digital set-top box, DVD, etc.) to HDMI/DVI
IN 1(DVI), HDMI IN 2 or HDMI IN 3 (Except for
42/50PJ2***) jack on the TV.
2
Turn on the external equipment.
3
Select HDMI1, HDMI2 or HDMI3 (Except for
42/50PJ2***) input source using the INPUT button on the remote control.
1
EXTERNAL EQUIPMENT SETUP
1
! NOTE
►Check that your HDMI cable is version 1.3 or higher. If the HDMI cables don’t support HDMI version
1.3,
2 flickering or no screen display can result. Please use the latest cables that support at least HDMI
version 1.3.
?
► HDMI mode supports PCM audio format only.
► Audio format was reseted to Dolby/DTS/Bitstrem in DVD Player or STB, it should be changed to PCM.
► We recommend using under 10m of the HDMI cable. When using over the length, connect a amplifier
or repeater.
► If the DVD does not support Auto HDMI, you must set the output resolution appropriately.
3
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH AN HDMI TO DVI CABLE
EXTERNAL EQUIPMENT SETUP
1
Connect the digital set-top box or the DVI output of the PC to HDMI/DVI IN 1(DVI) jack on
the TV.
2
Connect the audio output of the digital set-top
box or the PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
3
Turn on the digital set-top box or the PC and
the TV.
(Refer to the digital set-top box or the PC
manual for operating instructions.)
4
Select HDMI1 input source using the INPUT
button on the remote control.
1
or
USB SETUP (Except 42/50PJ2***)
1
4
2
1
Connect the USB device to the USB IN jack on the TV.
2
After connecting the USB IN jack, you use the USB function. ( p.31)
CONNECTING WITH AN RCA CABLE
Connect the AUDIO/VIDEO jacks between TV
and VCR or external equipment. Match the jack
colours (Video = yellow, Audio Left = white, and
Audio Right = red)
2
Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.)
Or, Operate the corresponding external equipment.
(Refer to external equipment operating guide.)
3
1
Select AV1 input source using the INPUT button on the remote control.
If connected to AV IN2, select AV2 input
source.
! NOTE
or
►►If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO jack of the TV.
EXTERNAL EQUIPMENT SETUP
1
?
Video Game Set
Camcorder
5
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH A RF CABLE
■ To avoid picture noise (interference), allow adequate distance between the VCR and TV.
EXTERNAL EQUIPMENT SETUP
1
Connect the ANTENNA OUT socket of the VCR to
the ANTENNA IN socket on the TV.
2
Connect the antenna cable to the ANTENNA IN
socket of the VCR.
3
Press the PLAY button on the VCR and match the
appropriate programme between the TV and VCR
for viewing.
1
2
Wall Jack
Antenna
EXTERNAL STEREO SETUP
Use to connected either an external amplifier, or add a subwoofer to your surround sound system.
1
Connect the input jack of the stereo amplifier to
the VARIABLE AUDIO OUT jacks on the TV.
2
Set up your speakers through your analog stereo
amplifier, according to the instructions provided
with the amplifier.
NOTE
►When
►
connecting with external audio equipments,
such as amplifiers or speakers, please turn the TV
speakers off.(► p.67)
6
1
CONNECTING WITH A D-SUB 15 PIN CABLE
(Except 42/50PJ2***)
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's
settings.
Connect the RGB output of the PC to the RGB
IN (PC) jack on the TV.
2
Connect the PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
3
Turn on the PC and the TV.
4
Select RGB input source using the INPUT button on the remote control.
2
1
EXTERNAL EQUIPMENT SETUP
1
7
EXTERNAL EQUIPMENT SETUP
SUPPORTED DISPLAY RESOLUTION
RGB-PC mode (Except 42/50PJ2***)
Resolution
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
Resolution
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
EXTERNAL EQUIPMENT SETUP
640x350
31.468
70.09
720x480
31.47
59.94
720x400
31.469
70.09
720x480
31.50
60.00
640x480
31.469
59.94
720x576
31.25
50.00
800x600
37.879
60.317
1280x720
44.96
59.94
1024x768
48.363
60.004
1280x720
45.00
60.00
1280x768
47.776
59.87
1280x720
37.50
50.00
1360x768
47.720
59.799
1920x1080
33.72
59.94
1280x1024
63.668
59.895
1920x1080
33.75
60.00
1920x1080
66.587
59.934
1920x1080
28.125
50.00
1920x1080
67.432
59.94
1920x1080
67.50
60.00
1920x1080
56.25
50.00
1920x1080
27.00
24.00
1920x1080
33.75
30.00
Only 50/60PK5***
Only 50PJ3***, 50PJ5***, 50PJ6***
!
NOTE
►►Avoid keeping a fixed image on the TV ’s screen for
prolonged periods of time. The fixed image may
become permanently imprinted on the screen; use
a screen saver when possible.
►►There may be interference relating to resolution,
vertical pattern, contrast or brightness in PC mode.
Change the PC mode to another resolution or
change the refresh rate to another rate or adjust
the brightness and contrast on the menu until the
picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC
graphic card.
►►The synchronization input waveform for Horizontal
and Vertical frequencies are separate.
►►We recommend using 1920x1080, 60 Hz(Only
50/60PK5***), 1360x768, 60 Hz(Only 50PJ3***,
50PJ5***, 50PJ6***), 1024x768, 60 Hz(Only
42PJ3***, 42PJ5***, 42PJ6***) for the PC
mode, this should provide the best picture quality.
?
8
HDMI/DTV mode
►►If the resolution of PC is over SXGA, there will be no
picture on the TV.(Only HD Models)
►►Connect the audio cable from the PC to the Audio
input on the TV.(Audio cables are not included with
the TV).
►►you use too long an RGB-PC cable, there may be
interference on the screen. We recommend using
under 5m of the cable. This provides the best picture
quality.
SCREEN SETUP FOR PC MODE
(Except 42/50PJ2***)
SCREEN RESET
Returns Position, Size and Phase to the factory default settings.
This function works in the following mode: Component(Except 480i, 576i), RGB.
Move
▲
2
3
4
5
Move
Prev.
Resolution
• Brightness
50
• Sharpness
60
• Colour
60
• Tint
0
R
G
• Colour Temperature0
W
C
• Advanced Control
• Picture Reset
Screen
Screen
1
Screen
OK
Auto Config.
Position
Size
To Set
Yes
No
Phase
Reset
EXTERNAL EQUIPMENT SETUP
PICTURE
Select PICTURE.
Select Screen.
Select Reset.
Select Yes.
Run Reset.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
9
EXTERNAL EQUIPMENT SETUP
AUTO CONFIGURE (RGB [PC] MODE ONLY)
Automatically adjust the picture position and minimizes image instability. After adjustment, if the image
is still not correct, your TV is functioning properly but needs further adjustment.
EXTERNAL EQUIPMENT SETUP
Auto configure
This function is for automatic adjustment of the screen position, size and phase The displayed image
will be unstable for a few seconds while the auto configuration is in progress.
PICTURE
Move
▲
Screen
OK
Move
Prev.
Resolution
• Brightness
50
• Sharpness
60
• Colour
60
• Tint
0
R
G
• Colour Temperature0
W
C
• Advanced Control
• Picture Reset
Auto Config.
Screen
Screen
Position
Size
To Set
Yes
No
Phase
Reset
1
2
3
4
5
Select PICTURE.
Select Screen.
• If the position of the image is still not correct,
try Auto adjustment again.
• If picture needs to be adjusted again after
Auto adjustment in RGB (PC), you can adjust
the Position, Size or Phase.
Select Auto Config..
Select Yes.
Run Auto Config..
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
10
SELECTING RESOLUTION
To view a normal picture, match the resolution of RGB mode at TV and selection at PC.
This function works in the following mode: RGB[PC] (1024x768, 1280x768, 1360x768)
Move
▲
Screen
OK
• Brightness
50
• Sharpness
60
• Colour
60
• Tint
0
R
G
• Colour Temperature0
W
C
• Advanced Control
• Picture Reset
Resolution
Auto Config.
Position
Move
Prev.
1024 x 768
1280 x 768
1360 x 768
Size
Phase
Screen
Screen
Reset
1
2
3
4
EXTERNAL EQUIPMENT SETUP
PICTURE
Select PICTURE.
Select Screen.
Select Resolution.
Select the desired resolution.
5
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
11
EXTERNAL EQUIPMENT SETUP
ADJUSTMENT FOR SCREEN POSITION, SIZE, PHASE
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the
picture phase manually.
EXTERNAL EQUIPMENT SETUP
Position operates in Component(except 480i, 576i), RGB mode.
Size, Phase operate only in RGB mode.
PICTURE
Move
▲
Screen
OK
Move
Prev.
Resolution
• Brightness
50
• Sharpness
60
• Colour
60
• Tint
0
R
G
• Colour Temperature0
W
C
• Advanced Control
• Picture Reset
Auto Config.
Position
Size
Phase
Screen
Screen
Reset
1
2
3
4
Select PICTURE.
Select Screen.
Select Position, Size or Phase.
Make appropriate adjustments.
5
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
12
WATCHING TV / PROGRAMME CONTROL
TURNING ON THE TV
- When your TV is turned on, you will be able to use its features.
1
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
2
In standby mode to turn TV on, press the / I, INPUT or P∧∨ button on the TV or press the
POWER, INPUT, P ∧∨ or NUMBER button on the remote control and the TV will switch on.
1
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can
adjust the Language, Mode Setting, Auto Tuning.
Note:
a.If you close without completing the initial setting, the Initial Setting menu can be displayed again.
b.“Store Demo” mode is only for shop display and not for general customer use.
c."Home Use” mode is the optimal setting for home environments, and is the TV's default mode.
d."Store Demo" mode is the optimal setting for store environments. If a user modifies image quality data, “Store Demo” mode initializes the product to the image quality set by us after a certain
period of time.
e.The mode (Home Use, Store Demo) can be changed by executing Mode Setting in the OPTION
menu.
PROGRAMME SELECTION
1
WATCHING TV / PROGRAMME CONTROL
INITIALIZING SETUP
Press the P∧∨ or NUMBER buttons to select a programme number.
VOLUME ADJUSTMENT
1
Press the
+ or - button to adjust the volume.
If you wish to switch the sound off, press the MUTE button.
You can cancel this function by pressing the MUTE,
+ , - or AV Mode button.
13
WATCHING TV / PROGRAMME CONTROL
QUICK MENU
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
Q.Menu (Quick Menu) is a menu of features which users might use frequently.
WATCHING TV / PROGRAMME CONTROL
• Aspect Ratio: Selects your desired picture format.
For Zoom Setting, select 16:9, Original, 4:3, 14:9, Zoom and Cinema Zoom in Ratio Menu. After
completing Zoom Setting, the display goes back to Q.Menu.
• Picture Mode : Selects your desired Picture Mode.
• Sound Mode : It is a feature to automatically set the sound combination which it deems the best
for the images being watched. Selects your desired Sound Mode.
• Audio : Selects the sound output.
• Sleep Timer : Sets the sleep timer.
• Favourite : Selects the favourite programme.
• USB Eject : Selects “Eject” in order to eject USB device. (Except for 42/50PJ2***)
Q. Menu
Aspect Ratio
◄
16:9
16:9
Picture Mode
Standard
Sound Mode
Standard
Audio
►
Mono
Sleep Timer
Favourite
Favourite
USB Eject
Off
Off
Eject
Except for 42/50PJ2***
Close
1
2
Display each menu.
Select your desired Source.
3
• Press the Q.MENU button to return to normal TV viewing.
14
ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
■ Image shown may differ from your TV.
SETUP
Move
OK
Auto Tuning
PICTURE
Move
Aspect Ratio
Energy Saving
Auto Volume
Move
Clear Voice II
: Off
• Level
• Contrast
70
Balance
• Brightness
90
Sound Mode
: Standard
• Sharpness
50
• Infinite Sound : Off
• Colour
70
• Treble
50
• Tint
• Bass
50
R
G
▼
3
-
+
0
L
R
▼
INPUT
Move
OK
TV
AV1
SETUP
PICTURE
AUDIO
AV2
Component1
Component2
or
TIME
OPTION
HDMI1
HDMI2
INPUT
USB
Only 42/50PJ2***
TIME
Move
OK
OPTION
Move
Menu Language
Clock
: English
OK
USB
Move
Photo List
Off Time
: Off
Input Label
On Time
: Off
SIMPLINK
: On
Movie List
Sleep Timer
: Off
Key Lock
: Off
DivX Reg. Code
Set ID
:1
Deactivation
ISM Method
:Normal
Music List
Demo Mode
: Off
Mode Setting
: Home Use
OK
WATCHING TV / PROGRAMME CONTROL
: Off
: Standard
0
OK
: Off
Picture Mode
Manual Tuning
Programme Edit
AUDIO
OK
: 16:9
▼
Except for 42/50PJ2***
1
2
3
Display each menu.
Select a menu item.
Move to the pop up menu.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
15
WATCHING TV / PROGRAMME CONTROL
AUTO PROGRAMME TUNING
Use this to automatically find and store all available programmes.
When you start auto programming, all previously stored service information will be deleted.
!
SETUP
Move
OK
SETUP
WATCHING TV / PROGRAMME CONTROL
Auto Tuning
Tuning
Auto
Manual Tuning
Auto Tuning
Programme Edit
Programme Edit
Manual Tuning
Move
?
Check your antenna connection. The
previous channel information will be
updated during Auto Tuning.
Still Continue?
Yes
1
2
3
4
Select SETUP.
Select Auto Tuning.
OK
No
• If you wish to keep on auto tuning select Yes
using the < >button. Then, press the OK button. Otherwise select No.
Select Yes.
Run Auto tuning.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
16
MANUAL PROGRAMME TUNING
Manual Tuning lets you manually tune and arrange the stations in whatever order you desire.
SETUP
Move
SETUP
OK
Move
OK
Auto Tuning
Auto Tuning
Manual Tuning
Programme Edit
Manual Tuning
Storage
Programme Edit
System
◄
1
►
BG
V/UHF
Channel
0
Fine
◄
►
Search
◄
►
Name
C 02
Store
Close
1
2
3
4
5
Select SETUP.
Select Manual Tuning.
or
Make appropriate
adjustments.
Select TV system.
6
7
8
Select V/UHF or Cable.
or
Select the desired
channel number.
Commence searching.
WATCHING TV / PROGRAMME CONTROL
Band
Select Store.
• Press the MENU button to return to normal TV viewing.
• Press the RETURN button to move to the previous menu screen.
• BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / NewZealand / M.East / Africa / Australia)
I : PAL I/II (U.K. / Ireland / Hong Kong / South Africa)
DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
M : NTSC-M (USA / Korea / Philippines), PAL-M(South America)
• To store another channel, repeat steps 3 to 8.
17
WATCHING TV / PROGRAMME CONTROL
SETUP
Move
SETUP
OK
Move
OK
Auto Tuning
Auto Tuning
Manual Tuning
Programme Edit
Manual Tuning
Storage
1
Programme Edit
System
BG
Band
V/UHF
Channel
0
Fine
◄
►
Search
◄
►
Name
C 02
Store
Close
WATCHING TV / PROGRAMME CONTROL
■■Assigning a station name
You can assign a station name with five characters to each programme number.
1
2
3
Select SETUP.
4
Select Manual Tuning.
Select Name.
5
Select the position and
make your choice of the
second character, and
so on.
You can use an the
alphabet A to Z, the
number 0 to 9, +/ -, and
blank.
Select Close.
■■Fine Tuning
Normally fine tuning is only necessary if reception is poor.
1
2
3
4
Select SETUP.
Select Manual Tuning.
5
Fine tune for the best picture
and sound.
Select Store.
Select Fine.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
18
PROGRAMME EDIT
When a programme number is skipped, it means that you will be unable to select it using P ∧∨ button
during TV viewing.
If you wish to select the skipped programme, directly enter the programme number with the NUMBER
buttons or select it in the Programme edit menu.
This function enables you to skip the stored programmes.
Move
9
OK
S11
Auto Tuning
0 -----
1 ARD
2 BBC1
Manual Tuning
4 C 01
5 S 46
6 C 05
7 C 06
Programme
ProgrammeEdit
Edit
8 C 10
4 S 11
4 C 52
11 -----
12 -----
13 -----
14 -----
15 -----
16 -----
17 -----
18 -----
19 -----
20 -----
21 -----
22 -----
23 -----
24 -----
25-----
26 -----
27 -----
28 -----
29 -----
30 -----
31 -----
Pr. Change
Delete
1
2
3
4
TV
Navigation
P
Page Change
Move
4 ARD
Previous
Skip
Select SETUP.
WATCHING TV / PROGRAMME CONTROL
SETUP
Select Programme Edit.
Enter the Programme Edit.
Select a programme to be stored or skipped.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
19
WATCHING TV / PROGRAMME CONTROL
This function enables you to delete or skip the stored programmes.
You can also move some channels and use other programme numbers.
■■Deleting a programme
1
2
3
Select a programme number to be deleted.
RED
Turn the deleted programme number to RED.
RED
Release the deleted programme.
following programmes are shifted up one.
WATCHING TV / PROGRAMME CONTROL
■■Moving a programme
1
Select a programme number to be moved.
2
GREEN
3
GREEN
Turn the moved programme number to GREEN.
Release the moved programme.
■■Skipping a programme number
1
Select a programme number to be skipped.
2
BLUE Turn the skipped programme number to BLUE.
3
BLUE Release the skipped programme.
20
•T
he selected programme is deleted, all the
• When a programme number is
skipped it means that you will be
unable to select it using the P ∧∨
button during normal TV viewing.
• If you wish to select a skipped programme, directly enter the programme
number with the NUMBER buttons or
select it in the programme edit.
SELECTING THE PROGRAMME LIST
You can check which programmes are stored in the memory by displaying the programme list.
Programme List
1 ARD
8:
2 BBC1
8:
3 ARD
8:
4 CO1
8:
5 S46
8:
6 C05
8:
7 C06
8:
8 C10
8:
9 S11
Exit
■■Displaying programme LIST
1
Display the Programme List.
• You may find some blue programmes. These
have been set up to be skipped by auto programming or in the programme edit mode.
•S
ome programmes with the channel number
shown in the programme list indicate there is no
station name assigned.
■■Selecting a programme in the programme list
1
WATCHING TV / PROGRAMME CONTROL
8:
Select a programme.
2
Switch to the chosen programme number.
■■Paging through a programme list
1
P
P
A
G
E
Turn the pages.
2
Return to normal TV viewing.
21
WATCHING TV / PROGRAMME CONTROL
FAVOURITE PROGRAMME SETUP
■■Selecting favourite programme
Favorite programmes is a convenient feature that lets you quickly scan up to programmes of your
choice without having to wait for the TV to scan through all the in-between programmes.
Q.Menu
1
Aspect Ratio
16:9
Picture Mode
Vivid
Sound Mode
Standard
Audio
or
2
Mono
WATCHING TV / PROGRAMME CONTROL
Sleep Timer
Favourite
Favourite
Off
◄ Favourite ►
USB Eject
Eject
3
4
Select your desired
programme.
Select Favourite.
Select Favourite.
Return to TV viewing.
Close
Except for 42/50PJ2***
•T
his will automatically include the selected programme into your favourite programme list.
■■ Displaying the favourite programme list
1
Favourite List
8:
1 ARD
8:
2 BBC1
8:
3 ARD
8:
4 CO1
8:
5 S46
8:
6 C05
8:
7 C06
8:
8 C10
8:
9 S11
Exit
22
Display the Favourite Programme List.
INPUT LIST
TV
HDMI3
AV1
AV2
HDMI2
1
•
•
•
•
•
INPUT
HDMI1
Component 2
RGB
Except for 42/50PJ2***
Select the input source.
TV : Select it when watching the TV.
AV : Select it when watching the VCR or external equipment.
Component : Select it when using DVD or Digital set-top box depends on connector.
RGB : Select it when using PC depends on connector.
HDMI : Select it when using DVD or Digital set-top box depend on connector.
WATCHING TV / PROGRAMME CONTROL
Except for 42/50PJ2***
Component 1
23
WATCHING TV / PROGRAMME CONTROL
INPUT LABEL
Selects a label for each input source.
OPTION
Move
Menu Language
OK
: English
WATCHING TV / PROGRAMME CONTROL
4
: English
SIMPLINK
: On
: Off
Key Lock
: Off
RGB
Set ID
:1
Set ID
:1
HDMI1
ISM Method
:Normal
ISM Method
:Normal
HDMI2
Demo Mode
: Off
Demo Mode
: Off
: Home Use
Mode Setting
: Home Use
►
Component 2
: On
▼
◄
Component 1
Key Lock
▼
3
Menu Language
OK
AV2
SIMPLINK
Mode Setting
2
Move
Input Label
Input Label
1
AV1
OPTION
Except for 42/50PJ2***
Except for 42/50PJ2***
HDMI3
Close
Select OPTION.
Select Input Label.
Select the source.
Select the label.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
24
SIMPLINK
This function operates only with devices with the SIMPLINK logo.
Please check the SIMPLINK logo.
The product might not function properly when using it with other products with HDMI-CEC function.
This allows you to control and play other AV devices connected to the display through HDMI cable without additional cables and settings.
If you do not require the SIMPLINK menu, select “Off”.
Move
Menu Language
: English
Input Label
Move
Menu Language
OK
: English
Off
SIMPLINK
SIMPLINK
: On
SIMPLINK
On
:: On
Key Lock
: Off
Key Lock
: Off
Set ID
:1
Set ID
:1
ISM Method
:Normal
ISM Method
:Normal
Demo Mode
: Off
Demo Mode
: Off
Mode Setting
: Home Use
Mode Setting
: Home Use
On
On
▼
Select OPTION.
2
Select SIMPLINK.
3
4
OPTION
Input Label
▼
1
OK
WATCHING TV / PROGRAMME CONTROL
OPTION
Select On or Off.
Save.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
25
WATCHING TV / PROGRAMME CONTROL
CONNECTING TO HOME THEATER WITH THE SIMPLINK LOGO.
WATCHING TV / PROGRAMME CONTROL
26
1
Connect the HDMI/DVI IN 1, HDMI IN 2, HDMI IN
3(Except for 42/50PJ2***) terminal on the back of
the TV and the HDMI output terminal of the Home
Theater using HDMI cables.
2
Connect the Audio output terminal on the back
of the TV and the Audio input terminal of the
Home theater using optical cable.
3
Select Home Theater in the Speaker menu by
pushing the SIMPLINK button.
1
►► When you select or operate a media device with home
theater function, the speaker automatically switches to
home theater speaker (HT speaker).
2
Home Theater
! NOTE
►►Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal and Side terminal (HDMI terminal)
of the SIMPLINK device with the HDMI cable.
►
?►When you switch the Input source using the INPUT button on the remote control, you can stop the operation
of a device controlled by SIMPLINK.
►►When the unit is connected to SIMPLINK Home Theater, set to Variable Out and turn off the TV Speaker to
operate the Home Theater Speaker. At this time, the maximum volume of the Home Theater Speaker is set
to the TV volume.
SIMPLINK FUNCTIONS
* A device, which is connected to the TV through an HDMI cable but does not support
SIMPLINK, does not provide this function.
Note: To operate SIMPLINK, an HDMI cable over Version 1.3 with *CEC function should be used.
(*CEC: Consumer Electronics Control).
SIMPLINK MENU
Press the ∧ ∨ <
1
2
3
4
5
>
button and then OK button to select the desired SIMPLINK source.
TV viewing : Switch to the previous TV programme regardless of the current mode.
DISC playback : Select and play connected
discs.
When multiple discs are available, the titles of
discs are conveniently displayed at the bottom
of the screen.
VCR playback : Play and control the connected VCR.
DD Recordings playback : Play and control
H
recordings stored in HDD.
1
Selected Device
2
When device is not
connected (displayed
in gray)
3
4
5
WATCHING TV / PROGRAMME CONTROL
Disc playback
Control connected AV devices by pressing the ∧/∨/< / >, OK, ►, ▀, l l, ◄◄ and ►► buttons.
Direct Play
After connecting AV devices to the TV, you can directly control the devices and play media without additional settings.
Select AV device
Enables you to select one of the AV devices connected to the TV and operate it.
Power off all devices
When you switch off the TV, all connected devices are turned off.
Switch audio-out
Offers an easy way to switch audio-out.
Sync Power on
When the equipment with Simplink function connected HDMI terminal starts to play, The TV will change automatically
to turn on mode.
►
When a device is
connected (displayed
in bright colour)
udio Out to Home theater/Audio Out to TV:
A
Select Home theater or TV speaker for Audio
Out.
27
WATCHING TV / PROGRAMME CONTROL
AV MODE
You can select the optimal images and sounds when connecting AV devices to external input.
Off
Cinema
Sport
Game
WATCHING TV / PROGRAMME CONTROL
1 AV MODE
Disables the AV MODE.
Optimizes video and audio for watching movies.
Optimizes video and audio for watching sports events.
Optimizes video and audio for playing games.
Off
Cinema
Game
Sport
Press the AV MODE button repeatedly to select the desired source.
2
• If you select Cinema in AV mode, Cinema will be selected both for
Picture Mode and Sound Mode in PICTURE menu and AUDIO menu
respectively.
• If you select “Off” in AV mode, the picture and image which you initially
set will be selected.
28
INITIALIZING (RESET TO ORIGINAL FACTORY SETTINGS)
Use to quickly reset all the menu options to their original factory preset values.
This function deletes all TV programmes.
When the Initial Setting is completed, you must restart the Initializing setup.
OK
▼
Input Label
SIMPLINK
: On
Key Lock
: Off
Set ID
:1
ISM Method
:Normal
Demo Mode
: Off
Mode Setting
: Home Use
Initial
InitialSetting
Setting
1
2
3
4
OPTION
Move
SIMPLINK
: On
Key Lock
: Off
Set ID
ISM Method
Demo Mode
Mode Setting
Initial
Initial Setting
Setting
OK
▼
Move
Input Label
:1
All user settings and channel settings
:Normal
will be reset. Still Continue?
: Off
: Home Use
Yes
No
Select OPTION.
WATCHING TV / PROGRAMME CONTROL
OPTION
Select Initial Setting
Select Yes.
Start Initial Reset.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
29
WATCHING TV / PROGRAMME CONTROL
KEY LOCK
The TV can be set so that the remote control is required to control it.
This feature can be used to prevent unauthorized viewing.
OPTION
Move
Menu Language
: English
WATCHING TV / PROGRAMME CONTROL
Input Label
4
Menu Language
OK
: English
SIMPLINK
: On
SIMPLINK
: On
:: Off
Off
Key Lock
:: Off
Off
Set ID
:1
Set ID
:1
ISM Method
:Normal
ISM Method
:Normal
Demo Mode
: Off
Demo Mode
: Off
Mode Setting
: Home Use
Mode Setting
: Home Use
Select Key Lock.
3
Move
Key Lock
Select OPTION.
2
OPTION
Input Label
▼
1
OK
Select On or Off.
Off
On
On
▼
• In Key Lock ‘On’, if the TV is turned off, to turn on the
TV, press the INPUT, P∧∨ button on the TV or
POWER INPUT, P∧∨ or NUMBER buttons on the
remote control then the set will be turned on.
• With the Key Lock On, the display '
Key Lock
On ’ appears on the screen if any button on the
front panel is pressed while viewing the TV.
Save.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
30
TO USE A USB DEVICE
►►It is not possible to use USB function in 42/50PJ2*** models.
WHEN CONNECTING A USB DEVICE
When you connect a USB device, this pop up menu is displayed, automatically.
“POP UP MENU” will not be displayed while the OSD including Menu is activated.
In USB device, you can not add a new folder or delete the existing folder.
■■ Here shown may be somewhat different from your TV.
1 Connect
the USB device to the USB IN
jack on the TV.
2
Select PHOTO LIST, MUSIC LIST or
MOVIE LIST.
PHOTO LIST
3
MUSIC LIST
MOVIE LIST
WHEN REMOVING THE USB DEVICE
Select the USB Eject menu before removing
the USB device.
1
2
Select Eject.
TO USE A USB DEVICE
USB memory stick
• This TV Supports on JPEG and MP3 and SD
DivX.
31
TO USE A USB DEVICE
PRECAUTIONS WHEN USING THE USB DEVICE
TO USE A USB DEVICE
32
►►Only a USB storage device is recognizable.
►►If the USB storage device is connected through a USB hub, the device is not recognizable.
►►A USB storage device using an automatic recognition programme may not be recognized.
►►A USB storage device which uses its own driver may not be recognized.
►►The recognition speed of a USB storage device may depend on each device.
►►Please do not turn off the TV or unplug the USB device when the connected USB storage device is working.
When such device is suddenly separated or unplugged, the stored files or the USB storage device may be
damaged.
►►Please do not connect the USB storage device which was artificially maneuvered on the PC. The device may
cause the product to malfunction or fail to be played. Never forget to use only a USB storage device which has
normal music files or image files.
►►Please use only a USB storage device which was formatted as a FAT16, FAT32, NTFS file system provided
with the Windows operating system. In case of a storage device formatted as a different utility programme
which is not supported by Windows, it may not be recognized.
Data in a USB storage device cannot be deleted in the NTFS file system.
►►Please connect power to a USB storage device which requires an external power supply. If not, the device may
not be recognized.
►►Please connect a USB storage device with cable is offered by USB maker. If connected with cable is not offered
by USB maker or an excessively long cable, the device may not be recognized.
►►Some USB storage devices may not be supported or operated smoothly.
►►Maximum of 999 files and 200 folders can be recognized.
►►Data in a USB storage device cannot be aligned.
►►Up to 128 English characters can be recognized as a file name.
►►Please back up the important file because a data of USB device may be damaged. Data management is consumer's responsibility and in consequence the manufactures does not cover the product bearing data damage.
►►If the USB is connected in Standby Mode, specific hard disk will automatically be loaded when the TV is turned
on.
►►The recommended capacity is 1 TB or less for a USB external hard disk and 32 GB or less for USB memory.
►►TV need more time to detect if the storage size is bigger. If the USB memory is connected in Standby Mode,
power on time would be longer than without memory.
►►Any device with more than the recommended capacity may not work properly.
►►If a USB external hard disk with a "Energy Saving" function does not work, turn the hard disk off and on again
to make it work properly.
! NOTE
■■ Image shown may differ from your TV.
■■ This feature is not available for all models.
►►In order to avoid losing the USB memory stick, use the USB connector (sold sepa?rately) to fix the USB memory stick to the USB connector holder of the TV.
USB connector holder
USB Input
port
USB Connector (sold separately)
- Fix the one and of the USB connector to the
USB memory stick and the other and to the
USB connector holder.
PHOTO LIST
You can view photo files on USB storage device.
The On Screen Display may be different from your TV. Images are an example to assist with the TV operation.
When you are watching the photo by the Photo List function, you can not change the picture mode.
TO USE A USB DEVICE
PHOTO(*.JPEG) supporting file
Baseline: Max 4800 x no limit
Min 64 X 64
• Not support to progressive jpeg.
• You can play JPEG files only.
• Only baseline scan is supported among JPEG (SOF0, SOF1 only).
• Non-supported files are displayed in the form of bitmap.
SCREEN COMPONENTS
1
2
Select USB.
Select Photo List.
2
1
2
3
4
Moves to upper level folder
Current page/Total pages
Total number of marked photos
Corresponding buttons on the
remote control
Photo List
Page 2/3
No Marked
Up Folder
Drive 1
JMJ001
1366x768, 125KB
1
3
Up Folder
KY103
09/10/2008
KY101
09/10/2008
KY104
09/10/2008
KY102
09/10/2008
KY105
09/10/2008
JMJ001
09/10/2008
JMJ005
09/10/2008
JMJ002
09/10/2008
JMJ006
09/10/2008
JMJ003
09/10/2008
JMJ007
09/10/2008
JMJ004
09/10/2008
JMJ008
09/10/2008
▼
Navigation
Popup Menu
P
Page Change
MARK
Mark
Exit
4
33
TO USE A USB DEVICE
PHOTO SELECTION AND POPUP MENU
Photo List
Page 2/3
Drive 1
1366x768, 125KB
Up Folder
Navigation
Popup Menu
Photo List
TO USE A USB DEVICE
1366x768, 125KB
Up Folder
2
3
4
09/10/2008
09/10/2008
KR104
09/10/2008
KR102
09/10/2008
KR105
09/10/2008
JMJ001
09/10/2008
JMJ005
09/10/2008
JMJ002
09/10/2008
JMJ006
09/10/2008
JMJ003
09/10/2008
JMJ007
09/10/2008
JMJ004
09/10/2008
JMJ008
09/10/2008
Page Change
P
MARK
Popup Menu
Mark
KR103
KR101
09/10/2008
KR104
KR102
09/10/2008
KR105
JMJ001
09/10/2008
JMJ005
JMJ002
09/10/2008
JMJ003
09/10/2008
JMJ004
09/10/2008
P
Exit
No Marked
Up Folder
JMJ001
1
KR103
KR101
Page 2/3
Drive 1
Navigation
No Marked
Up Folder
JMJ001
Page Change
09/10/2008
09/10/2008
09/10/2008
1366x768, 125KB
09/10/2008
View
JMJ006
09/10/2008
Mark All
JMJ007
09/10/2008
Delete
JMJ008
Close 09/10/2008
MARK
Mark
►►View : Display the selected item.
►►Mark All : Mark all photos on the screen.
►►Unmark All : Deselect all marked photos.
►►Delete : Delete the selected photo item.
►►Close : Close the pop-up menu.
Exit
Select the target folder or drive.
Select the desired photos.
Show the PopUp menu.
Select the desired PopUp
menu.
• Use the P∧∨ button to navigation in the photo
page.
• Use the MARK button to mark or unmark a
photo. When one or more photos are marked,
you can view each marked photo or a slide
show of the marked photos. If no photos are
marked, you can view every individual photo
in the folder or a slide show of all photos in the
folder.
• Press the BACK button to return to normal TV viewing.
34
SET UP THE MENU IN FULL-SIZED SCREEN
You can change the settings to display photos stored on a USB device, on a full-sized screen.
Detailed operations are available on full-sized photo view screen.
Photo List
Page 2/3
Drive 1
1366x768, 125KB
Up Folder
Navigation
No Marked
Up Folder
JMJ001
Popup Menu
09/10/2008
09/10/2008
KR104
09/10/2008
KR102
09/10/2008
KR105
09/10/2008
JMJ001
09/10/2008
JMJ005
09/10/2008
JMJ002
09/10/2008
JMJ006
09/10/2008
JMJ003
09/10/2008
JMJ007
09/10/2008
JMJ004
09/10/2008
JMJ008
09/10/2008
P
Page 2/3
Drive 1
Page Change
1366x768, 125KB
Up Folder
Mark
Exit
No Marked
Up Folder
JMJ001
MARK
KR103
KR101
09/10/2008
KR104
KR102
09/10/2008
KR105
JMJ001
09/10/2008
JMJ005
JMJ002
09/10/2008
JMJ006
JMJ003
09/10/2008
JMJ004
09/10/2008
09/10/2008
09/10/2008
09/10/2008
1366x768, 125KB
View
09/10/2008
09/10/2008
Mark All
JMJ007
09/10/2008
Delete
JMJ008Close
09/10/2008
1/17
1/17
Slideshow
Navigation
Popup Menu
P
Page Change
MARK
Mark
Exit
BGM
Q.MENU
Delete
Option
Hide
The aspect ratio of a photo may change the size
of the photo displayed on the screen in full size.
Press the EXIT button to move to the previous
menu screen.
1
2
TO USE A USB DEVICE
Photo List
KR103
KR101
Select the target folder or drive.
Select the desired photos.
3
Show the PopUp menu.
4
Select View.
5
The selected photo is displayed in full size.
35
TO USE A USB DEVICE
6
Select the Slideshow , BGM,
Delete or Hide.
• Use
1/17
1/17
Slideshow
BGM
Q.MENU
Delete
Option
Hide
< > button to select the previous or next
photo.
• Use < > button to select and control the menu
on the full-sized screen.
►►Slideshow : When no picture is selected, all photos in the current
folder are displayed during slide show. If some photos are selected, those photos are displayed in a slide show.
■ Set the time interval of the slide show in Option.
TO USE A USB DEVICE
►►BGM (Background Music) : Listen to music while viewing photos
in full size.
■ Set the Music Folder for BGM in Options before using this
function.
►►
(Rotate) : Rotate photos.
■ Rotates the photo 90°, 180°, 270°, 360° clockwise.
►►Delete : Delete photos.
►► Hide : Hide the menu on the full-sized screen.
■ To see the menu again on the full-sized screen, press OK
button to display.
36
(Rotate),
USING THE PHOTO LIST FUNCTION
Choose Options
Set Photo View.
1/17
1/17
Slideshow
BGM
Q.MENU
Delete
Option
Set Video.
Hide
Set Audio.
Prev.
! NOTE
?
1
2
Select the PopUp menu.
Select Set Photo View, Set Video or Set Audio.
TO USE A USB DEVICE
►►If you select “Off” for TV speaker, Set Audio features in Choose Options will not work.
►►When you select the Set Photo View.
■ You cannot change Music Folder while BGM is playing.
Press ◄ ► to set the time interval between slides.
Slide Speed
Fast
Music Folder
Prev.
1
Show the Slide Speed or Music Folder.
2
Make appropriate adjustments.
37
TO USE A USB DEVICE
►►When you select the Set Video.
Set Video.
Picture Mode
Vivid
Contrast
100
Brightness
50
Sharpness
70
Colour
70
Tint
0
Colour Temperature
0
Noise Reduction
Off
Picture Reset
TO USE A USB DEVICE
Prev.
1
! NOTE
►►
mode is not supported in Set Video function.
?
Make appropriate adjustments.(Refer to p.53 to 55, 58)
►►When you select the Set Audio.
Set Audio.
Sound Mode
Cinema
Auto Volume
Off
Clear Voice II
Off
Balance
0
Prev.
38
1
Show the Sound Mode, Auto Volume, Clear Voice II and Balance.
2
Make appropriate adjustments. (Refer to p.62 to 66)
MUSIC LIST
Purchased m files(*.MP3) may contain copyright restrictions. Playback of these files may not be supported by this model.
Music file on your USB device can be played by this unit.
The On Screen Display may be different from your TV. Images are an example to assist with the TV
operation.
MUSIC (*.MP3) supporting file
Bit rate : 32 k to 320kbps
Sampling rate MPEG1 layer 3 : 32 k to 48 kHz
SCREEN COMPONENTS
2
Select USB.
Select Music List.
2
1
2
3
4
Moves to upper level folder
Current page/Total pages
Total number of marked
music title
Corresponding buttons on
the remote control
Music List
Page 2/3
Up Folder
Popup Menu
Duration
Up Folder
00:00/01:34
Navigation
No Marked
Title
Music
004. Sweet Box-Love...
1
3
P
001. S001. mp3
03:33
003. S002.mp3
04:45
004. S003.mp3
01:30
006. S004.mp3
02:37
007. S005.mp3
01:58
Page Change
Option
MARK
Mark
TO USE A USB DEVICE
1
Exit
4
39
TO USE A USB DEVICE
MUSIC SELECTION AND POPUP MENU
As shown, up to 6 music titles are listed per page.
Music List
Page 2/3
No Marked
Title
Music
004.SweetBox-Love..
Up Folder
Navigation
001. S001. mp3
03:33
003. S002.mp3
04:45
004. S003.mp3
01:30
006. S004.mp3
02:37
007. S005.mp3
01:58
Popup Menu P
TO USE A USB DEVICE
Music List
Duration
Up Folder
Page Change
Page 2/3
Option
MARK
Mark
No Marked
Title
Music
004.SweetBox-Love..
Duration
Up Folder
001. S001. mp3
03:33
003. S002.mp3
04:45
004. S003.mp3
01:30
4395KB
1Kbps02:37
006. S004.mp3
Up Folder
Navigation
Exit
Play
007. S005.mp3
Popup Menu P
Page Change
01:58
Play with Photo
Option
Mark All
Mark
MARK
Delete
Exit
Close
1
2
3
4
Select the target folder or drive.
►►Play (During stop) : Play the selected music
titles.
Once a music finishes playing, the next selected one will be played. When there are no
selected music titles to play, the next one in the
current folder will be played.
►►Play Marked : Play the selected music titles.
Once a music finishes playing, the next selected one will be played automatically.
►►Stop Play (During playback) : Stop the playing
music titles.
►►Play with Photo : Start playing the selected
music titles and then move to the Photo List.
►►Mark All : Mark all music titles in the folder.
►►Unmark All : Deselect all marked music titles.
►►Delete : Delete the selected music titles.
►►Close : Close the pop-up menu.
• Use the P∧∨ button to navigate up/down in
Select the desired music title.
Show the PopUp menu.
Select the desired PopUp menu.
the music page.
• Use MARK button to mark or unmark a music.
When one or more music files are marked, the
marked music title will be played in sequence.
For example, if you want to listen to only one
music repeatedly, just mark the music only
and play it. If no music is marked, all the music
in the folder will be played in sequence.
• Press the BACK button to return to normal TV viewing.
40
USING THE MUSIC LIST FUNTION, PLAY
Music List
Page 2/3
Duration
Sound Mode
Cinema
001. S001. mp3
03:33
Auto Volume
Off
003. S002.mp3
04:45
Clear Voice II
Off
Title
Music
004.SweetBox-Love..
Up Folder
Navigation
Set Audio.
No Marked
Up Folder
004. S003.mp3
01:30
006. S004.mp3
02:37
007. S005.mp3
01:58
Popup Menu P
Page Change
Option
MARK
Mark
Balance
Exit
1
Show the Sound Mode.
2
Make appropriate adjustments. (Refer to p.62 to 66)
0
Prev.
►►If you select “Off” for TV speaker, Set Audio will not work.
?
■■ If you don't press any button for a while during the playing, the
play information box (as shown in the below) will float as a
screen saver.
■■ The ‘Screen Saver’?
Screen saver is to prevent screen pixel damage due to an fixed
image remaining on the screen for a extended period of time.
TO USE A USB DEVICE
! NOTE
! NOTE
►►When a music file is played,
is displayed behind the title.
►►A damaged or corrupted music does not play but displays 00:00 in playtime.
?
►►A music downloaded from a paid service with copyright protection does not start but displays inappropriate
information in playtime.
►►If you press OK, ■ buttons, screen saver is stopped.
►►This TV can not play music files less than 32 Kbytes.
►►The PLAY(►), Pause(II), ■ , ►►, ◄◄ buttons on the remote control are also available in this mode.
►►You can use the ►► button to select the next music and the ◄◄ button to select the previous music.
41
TO USE A USB DEVICE
MOVIE LIST
The movie list is activated once USB is detected. It is used when playing movie files on TV.
Displays the movies in the USB folder and supports Play.
Allows playback of all movies in the folder and user desired files.
Editing such as delete and add is not allowed.
It is a movie list that displays folder information and DivX file.
Supports up to four drives.
TO USE A USB DEVICE
MOVIE(*.avi/*.DivX) supporting file
Video format : MPEG1 , MPEG2, MPEG4 (Doesn’t support Microsoft MPEG4-V2, V3), DivX 3.xx ,
DivX 4.xx, DivX 5.xx , DivX VOD ( DRM ) , XviD, DivX 6.xx(Playback)
Audio format : Mpeg, Mp3, PCM, Dolby Digital.
Sampling frequency : 32 k to 48 kHz
Bit rate : 32 k to 320 kbps
Subtitle format : *.smi/ *.srt/ *.sub(MicroDVD, SubViewer 2.0)/ *.ass/ *.ssa/*.txt(DVD Subtitle System)
• Some user-created subtitles may not work properly.
• Time information in an external subtitle file should be arranged in ascending order to be played.
• The video file and the subtitle file must be located in the same folder.
• The name of the video file and the subtitle file must be the same to view the subtitles normally.
• If the video and audio structure of recorded file is not interleaved, either video or audio is outputted.
• Playing a video via a USB connection that does not support high speed may not work properly.
• USB storage devices below USB 2.0 are supported as well. But they may not work properly in the
movie list.
• DivX may not be played depending on its types or recording methods.
• If the video and audio structure of recorded file is not interleaved, either video or audio is outputted.
• Max bitrate of playable DivX is 4 Mbps.
• Maximum FPS (Frame Per Second) can be reached only at SD level. FPS is 25 FPS (720*576) or
30 FPS (720*480) depending on Resolution.
• Files of 25 FPS or 30 FPS of higher may not be played properly.
• Files encoded with GMC(Global Motion Compensation) may not be played.
• Certain video files created with an encoder may not be played.
• Some of subtitle files that are not ordered in sequence may not be display.
Extension name
Video Decoder
Audio Codec
mpg, mpeg, mpe, vob, dat
MPEG1, MPEG2
AC3,MPEG,MP3,PCM
720x576@25p
MPEG 4-SP, MPEG4-ASP, DivX 3.xx,DivX 4.xx,
Avi, DivX, m4v
DivX 5.xx, DivX 6.xx(Playback),
Xvid
42
Resolution
AC3,MPEG,MP3,PCM
720x480@30p
SCREEN COMPONENTS
1
2
Select USB.
Select Movie List.
2
1
2
3
4
Moves to upper level folder
Current page/Total pages
Total number of marked
movie title
Corresponding buttons on
the remote control
Movie List
3
Page 2/3
No Marked
movie
Title
Duration
Up Folder
640x480, 720KB
1
Up Folder
00:03:33
B001
00:04:45
B002
00:01:13
B003
00:03:13
B004
00:02:51
Popup Menu
P
Page Change
MARK
Mark
Exit
4
! NOTE
►► A DivX movie file and its subtitle file must be located in the same folder.
►► A video file name and its subtitle file name must be identical for it to be displayed.
►► Use the left/right (< / >) keys to move to a specific frame forward or backward while playing a movie.
?
(The left/right (< / >) keys may not work properly for some files while playing a movie.)
TO USE A USB DEVICE
Navigation
Favorite Music
43
TO USE A USB DEVICE
MOVIE SELECTION AND POPUP MENU
Movie List
Page 2/3
Duration
Up Folder
640x480, 720KB
Up Folder
Navigation
No Marked
Title
movie
Popup Menu
Movie List
Favorite Music
00:03:33
B001
00:04:45
B002
00:01:13
B003
00:03:13
B004
00:02:51
P
Page 2/3
Page Change
MARK
Mark
No Marked
Title
movie
Duration
Up Folder
TO USE A USB DEVICE
Favorite Music
00:03:33
B001
2
3
4
00:01:13
1366x768, 125KB
B003
Up Folder
1
00:04:45
B002
640x480, 720KB
Navigation
Exit
Play
B004
Popup Menu
P
00:03:13
00:02:51
Mark All
Page Change
MARK
Delete
Mark
Close
Exit
►►Play : Play the selected movie titles. DivX Play is
executed while screen changes.
►►Play Marked : Play the selected movie titles. Once a
movie finishes playing, the next selected one will be
played automatically.
►►Mark Al l : Mark all movie titles in the folder.
►►Unmark Al l : Deselect all marked movie titles.
►►Delete : Delete the selected movie titles.
►►Close : Close the pop-up menu.
• In the case of files not supported, a message regard-
Select the target folder or drive.
ing non-supported file is displayed.
Select the desired movie title
Show the PopUp menu.
Select the desired PopUp menu.
• Press the BACK button to return to normal TV viewing.
44
USING THE MUSIC LIST FUNTION, PLAY
Choose Options.
Set Video Play.
Set Video.
Set Audio.
Q. MENU Option
Prev.
! NOTE
►►If you select “Off” for TV speaker, Set Audio features in Choose Options will not work.
1
Select the PopUp menu.
2
Select Set Video Play, Set Video or Set Audio.
►►When you select the Set Video Play.
Set Video Play.
Picture Size
Audio Language
◄
Full Screen
►
1 / 8(AC3)
Subtitle Language
1/8
. Language
---
. Sync
---
. Position
---
Prev.
TO USE A USB DEVICE
?
►►Picture Size : Select your desired picture format during movie
play.
►►Audio Language & Subtitle Language : Change the Language
Group of the audio/subtitle during movie play.
►►Sync : Adjusts the time synchronisation of the subtitle from -10
secs to +10 secs by steps of 0.5 secs during movie play
►Position
►
: Changes the Position of the subtitle either up
or down during movie play
1
Show the Picture Size, Audio Language, or Subtitle Language.
2
Make appropriate adjustments.
45
TO USE A USB DEVICE
Subtitle Language
Support Language
Latin1
French, Spanish, Catalan Basque, Portuguese, Italian, Albanian, RhaetoRomanic, Dutch, German, Danish, Swedish, Norwegian, Finnish, Faroese,
Icelandic, Irish, Scottish, English
Latin2
Czech, Hungarian, Ploish, Romanian, Croatian, Slovak, Slovenian, Sorvian
Latin4
Estonian, the Baltic languages Latvian(Lettish) and Lithuanian, Greenlandic
and Lappish
Latin5
English, Trukish
Cyrillic
Bulgarian, Byelorussian, Macedonian, Russian, Serbian and pre-1990
(no ghe with upturn) Ukrainian
Greek
English, modern Greek
Hebrew
English, modern Hebrew
Chinese
Chinese
Thai
Arabic
Thai
English, Arabic
! NOTE
TO USE A USB DEVICE
►►Some special characters are not supported in subtitles.
►►HTML tags are not supported in subtitles.
►►Subtitles in languages other than the supported languages are not available.
?
►►When you select the Set Video.
Set Video.
Picture Mode
Vivid
Contrast
100
Brightness
50
Sharpness
70
Colour
70
Tint
0
Colour Temperature
0
Noise Reduction
Off
! NOTE
Picture Reset
Prev.
1
46
►►
?
mode is not supported in Set Video function.
Make appropriate adjustments. (Refer to p.53 to 55, 58)
►►When you select the Set Audio.
Set Audio.
Sound Mode
Cinema
Auto Volume
Off
Clear Voice II
Off
Balance
0
Prev.
Show the Sound Mode, Auto Volume, Clear Voice II and Balance.
2
Make appropriate adjustments. (Refer to p.62 to 66)
USING THE REMOTE CONTROL
◄◄ / ►►
II
When playing,
repeatedly, press the REW(◄◄) button to speed up ◄◄(x2) -> ◄◄◄(x4) ->
◄◄◄◄(x8) ->◄◄◄◄◄(x16) ->◄◄◄◄◄◄(x32) .
repeatedly, press the FF(►►) button to speed up ►►(x2)-> ►►►(x4) ->
►►►►(x8) ->►►►►►(x16) -> ►►►►►►(x32).
■■ Pressing these buttons repeatedly increases the fast forward/reverse speed.
During playback, press the Pause(II) button.
■■ Still screen is displayed.
PLAY(►)
■■ When using the < or > button during playback a cursor indicating the position can
be viewed on the screen.
Press the PLAY(►) button to return to normal playback.
STOP (■)
During playback, press the Stop(■) button.
■■ Stop the playing movie.
<>
TO USE A USB DEVICE
1
47
TO USE A USB DEVICE
DIVX REGISTRATION CODE
Confirm the DivX registration code number of the TV. Using the registration number, movies can be
rented or purchased at www.divx.com/vod.
With a DivX registration code from other TV, playback of rented or purchased DivX file is not allowed.
(Only DivX files matched with the registration code of the purchased TV are playable.)
USB
Move
USB
OK
Move
OK
Photo List
Photo List
Music List
Music List
Movie List
DivXReg.
Reg. Code
Code
DivX
i
Your registration Code is: xxxxxxxxxx
Deactivation
Deactivation
DivX(R) Video On Demand
Movie List
DivX Reg.
Reg. Code
Code
DivX
To learn more visit www.divx.com/vod.
Close
1
Select USB.
TO USE A USB DEVICE
2
3
Select DivX Reg. Code.
Display DivX Reg. Code.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
Manufactured under license from Dolby Laboratories. “Dolby “and the double-D
symbol are trademarks of Dolby Laboratories.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX,Inc. This is an
official DivX Certified device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in
order to play DivX Video-on-Demand (VOD) content. To generate the registration code,
locate the DivX VOD section in the device setup menu. Go to vod.divx.com with this
code to complete the registration process and learn more about DivX VOD.
“ DivX Certified to play DivX video, including premium content”
“Pat. 7,295,673; 7,460,688;7,519,274”
! NOTE
Supported movie file
?
Resolution : under 720 x 480(720x576) WxH pixels.
Frame rate : under 30 frames/sec
►Video
►
Codec : MPEG1, MPEG2, MPEG4(Doesn’t support Microsoft MPEG4-V2, V3), DivX3.xx,
DivX4.xx, DivX5.xx, DivX VOD(DRM), XviD, DivX 6.xx(Playback).
►When
►
loading, some buttons may not work.
►If
► you use the DivX registration code of another device, the rented or purchased DivX file cannot
be played. Therefore always use the DivX registration code assigned to this product.
48
DEACTIVATION
Delete the existing authentication information to receive a new DivX user authentication for TV.
Once this function is executed, a DivX user authentication is required again to see DivX DRM files.
USB
Move
OK
USB
Photo List
Photo List
Music List
Music List
Movie List
Movie List
DivX Reg. Code
DivX Reg. Code
Deactivation
Deactivation
Deactivation
Deactivation
Move
OK
i
DivX(R) Video On Demand
Do you want to deactivate your device?
Yes
2
3
TO USE A USB DEVICE
1
No
Select USB.
Select Deactivation.
Select Yes.
4
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
49
PICTURE CONTROL
PICTURE SIZE (ASPECT RATIO) CONTROL
You can watch the screen in various picture formats; 16:9, Just Scan, Original, 4:3, 14:9, Zoom and
Cinema Zoom1.
If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on
the screen and remain visible.
1
2
Select Aspect Ratio.
PICTURE or Q.Menu menu.
Select the desired picture format.
PICTURE CONTROL
• 16:9
The following selection will allow you to adjust the picture
horizontally, in linear proportion, to fill the entire
screen(useful for viewing 4:3 formatted DVDs).
• Original
When your TV receives a wide screen signal it will automatically change to the picture format broadcast.
Original
• Just Scan
Following Selection will lead to you view the
picture of best quality without loss of original
picture in high resolution image.
Note : If there is noise in original Picture, You
can see the noise at the edge.
Just Scan
50
•Y
ou can also adjust Aspect Ratio in the
• 4:3
The following selection will allow you to view a picture
with an original 4:3 aspect ratio, gray bars will appear on
both the left and right of the screen.
Full Wide
• 14:9
You can view a picture format of 14:9 or a general TV
programme in the 14:9 mode. The 14:9 screen is viewed
in the same way as in 4:3, but is magnified to the left and
right.
• Cinema Zoom1
Choose Cinema Zoom when you want to
enlarge the picture in correct proportion.
Note:When enlarging or reducing the picture,
the image may become distorted.
• Zoom
The following selection will allow you to view the
picture without any alteration, while filling the
entire screen. However, the top and bottom of
the picture will be cropped.
PICTURE CONTROL
! NOTE
►You
►
can only select 4:3, 16:9 (Wide) in RGB mode only.
►In
► HDMI/Component (over 720p) mode, Just Scan is available.
?
51
PICTURE CONTROL
ENERGY SAVING
It reduces the plasma display’s power consumption.
The default factory setting complies with the Energy Star requirements and is adjusted to the comfortable level to be viewed at home.
You can increase the brightness of your screen by adjusting the Energy Saving level or by setting the
Picture Mode.
PICTURE
Aspect Ratio
Move
PICTURE
OK
: 16:9
Aspect Ratio
Energy Saving
Saving: Intelligent
: Off Sensor
Energy
Picture Mode
: Standard
PICTURE CONTROL
2
3
OK
• Contrast
70
Energy Saving
Saving: Intelligent
: Off Sensor
Energy
Intelligent Sensor
Picture Mode
: Standard
Off
• Contrast
70
• Brightness
90
• Sharpness
50
• Brightness Minimum
90
• Sharpness Medium
50
• Colour
70
• Colour
• Tint
• Tint
0
R
G
▼
1
Move
: 16:9
Maximum
70
Screen
0 Off
▼
Select PICTURE.
Select
Energy Saving.
Select Intelligent Sensor, Off, Minimum, Medium, Maximum or Screen Off.
4
• When the Intelligent sensor function is on, the most suitable picture is automatically adjusted according to the surrounding conditions.
• Intelligent Sensor : Adjusts picture according to the surrounding conditions.
• Screen Off : When you select Screen Off, the screen will be turned off in 3 seconds and Screen Off will start.
If you do not press any button for 2 hours, the power of the TV will automatically be turned off.
• You can also adjust Energy Saving button.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
52
PRESET PICTURE SETTINGS
PICTURE MODE-PRESET
Vivid
Strengthen the contrast, brightness, colour and sharpness for vivid picture.
Standard
The most general screen display status.
Maximize reducting the power consumption without hurting the picture quality.
Optimizes power consumption.
(Auto Power Saving)
Cinema
Optimizes video for watching movies.
Sport
Optimizes video for watching sports events.
Game
Optimizes video for playing games.
PICTURE
Aspect Ratio
Energy Saving
Move
PICTURE
OK
: 16:9
Aspect Ratio
: Off
Picture Mode
: :Standard
Vivid
• Contrast
Energy Saving
: :Standard
Vivid
70
• Contrast
• Brightness
90
• Sharpness
50
• Colour
70
• Tint
0
R
G
3
Vivid
Vivid
70
Standard
• Brightness 90
• Sharpness 50
Cinema
• Colour
70
Sport
• Tint
0 R
Game
▼
G
• Picture Mode adjusts the TV for the best
Select PICTURE.
Select Picture Mode.
Select Vivid, Standard,
Cinema, Sport or Game.
,
picture appearance. Select the preset
value in the Picture Mode menu based
on the programme category.
• You can also adjust Picture Mode in the
Q. Menu.
PICTURE CONTROL
2
OK
: Off
Picture Mode
▼
1
Move
: 16:9
4
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
53
PICTURE CONTROL
MANUAL PICTURE ADJUSTMENT
PICTURE MODE-USER OPTION
Contrast
Adjusts the signal level between black and white in the picture.
Brightness
Adjusts the base level of the signal in the picture.
Sharpness
Adjusts the level of crispness in the edges between the light and dark areas of the picture.
The lower the level, the softer the image.
Colour
Adjusts intensity of all colours.
Tint
Adjusts the balance between red and green levels.
Colour Temperature
Adjust the balance between red(warm) and blue(cool) level of white balance.
PICTURE
Move
OK
: 16:9
: Off
: Standard
Contrast
•• Contrast
100
70
• Brightness
90
• Sharpness
50
• Colour
70
• Tint
0
88
▼
R
▼
• Contrast
Picture Mode
▼
Energy Saving
▼
Aspect Ratio
OK
G
▼
PICTURE CONTROL
1
2
3
4
5
Select PICTURE.
Select Picture Mode.
Select Vivid, Standard,
, Cinema, Sport or Game.
Select Contrast, Brightness, Sharpness, Colour, Tint or Colour Temperature.
Make appropriate adjustments.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
! NOTE
►►You cannot adjust colour, sharpness and tint in the RGB-PC mode.
54
?
PICTURE IMPROVEMENT TECHNOLOGY
Dynamic Contrast(Off/Low/High)
Adjusts the contrast to keep it at the best level according to the brightness of the screen. The resolution
of gradation is improved by making bright parts brighter and dark parts darker. This feature refers to
dynamic contrast, and enhances the feeling of presence that contrast controls are intended to give by
using dimming and other input signals.
Dynamic Colour(Off/Low/Medium/High )
Adjusts screen colours so that they look livelier, richer and clearer. This feature enhances hue, saturation
and luminance so that red, blue, green and white look more vivid.
Noise Reduction(Off/Low/Medium/High)
Reduces screen noise without compromising video quality. This feature is also used to reduce recursive
noise and MPEG noise (Mosquito/Block).
Gamma(Low/Medium/High)
You can adjust brightness of dark area and middle gray level area of the picture.
• Low : Make dark and middle gray level area of the picture brighten.
• Medium: Express original picture gradation.
• High: Make dark and middle gray level area of the picture darken.
PICTURE
Move
PICTURE
OK
▼
• Brightness
50
• Sharpness
70
60
Move
OK
• Brightness
• Colour
• Tint
0
R
G
50
Dynamic Contrast
• Sharpness 70
Dynamic Colour
• RColour
60
Noise
• Tint
0 Reduction
•Colour Temperature 0
W
C
Gamma
•Colour Temperature
0 R
• Advanced Control
•Advanced Control
Black Level
• Advanced Control
• Picture Reset
• Picture ResetFilm Mode
◄
►
Medium
G
Medium
Auto
Off
Screen
Screen
Off
High
Close
1
2
3
4
PICTURE CONTROL
Select PICTURE.
Select Advanced Control.
Select Dynamic Contrast, Dynamic Colour, Noise Reduction, Gamma, Black Level
or Film Mode.
Select your desired Source.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
55
PICTURE CONTROL
ADVANCED - BLACK(DARKNESS) LEVEL
Makes dark parts on the screen look darker.
This function works in the following mode: TV, AV, COMPONENT or HDMI.
Move
PICTURE
OK
Move
▼
PICTURE
OK
▼
• Brightness
50
• Brightness
• Sharpness
70
• Sharpness
• Colour
60
• RColour
• Tint
0
R
G
• Tint
•Colour Temperature 0
W
C
R0
•Colour TemperatureGamma
•Advanced Control
Black Level
• Advanced Control
• Picture Reset
• Advanced Control
• Advanced Control
• Picture Reset
50
Dynamic Contrast
70
Dynamic Colour
60
Noise
0 Reduction
Film Mode
High
High
Medium
G
Medium
◄
►
Off
Screen
Screen
Low
Close
PICTURE CONTROL
1
2
3
4
Select PICTURE.
Select Advanced Control.
• Low : The reflection of the screen gets darker.
• High : The reflection of the screen gets brighter.
• Auto : Realizing the black level of the screen and
set it to High or Low automatically.
Select Black Level.
Select Low or High.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
56
ADVANCED - FILM MODE
Makes video clips recorded in film look more natural.
This feature operates only in TV, AV and Component 480i/576i mode.
Move
PICTURE
OK
Move
▼
PICTURE
OK
▼
• Brightness
50
• Brightness
• Sharpness
70
• Sharpness
• Colour
60
• RColour
• Tint
0
R
G
• Tint
•Colour Temperature 0
W
C
R0
Gamma
•Colour Temperature
••Advanced
AdvancedControl
Control
•Advanced Control
Black Level
• Advanced Control
• Picture Reset
• Picture Reset Film Mode
Screen
Screen
50
Dynamic Contrast
70
Dynamic Colour
60
Noise
0 Reduction
High
High
Medium
G
Medium
Auto
◄
Off
►
Close
Select PICTURE.
2
Select Advanced Control.
3
Select Film Mode.
4
PICTURE CONTROL
1
Select On or Off.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
57
PICTURE CONTROL
PICTURE RESET
Settings of the selected picture modes return to the default factory settings.
Move
▼
PICTURE CONTROL
2
3
Move
• Brightness
50
• Sharpness
70
• Colour
60
• Tint
0
R
G
•Colour Temperature 0
W
C
• Advanced Control
•Colour Temp
PictureReset
Reset
••Picture
• Advanced Control
PictureReset
Reset
••Picture
• Brightness
50
• Sharpness
70
• Colour
60
Screen
1
PICTURE
OK
▼
PICTURE
• Tint
Resetting video
configuration.... 0
OK
R
G
0R
G
Screen
Select PICTURE.
Select Picture Reset.
Initialize the adjusted value.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
58
IMAGE STICKING MINIMIZATION (ISM) METHOD
A frozen or still picture from a PC/Video game displayed on the screen for prolonged periods will result
in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain
on the screen for prolonged periods.
Normal
If image sticking is never a problem, ISM is not necessary - set to Normal.
Orbiter
Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on
the screen. To avoid a permanent image on the screen, the screen will move every 2 minutes.
Colour Wash
The colour block with the screen moved a little and the white pattern are alternately displayed. It is
difficult to sense the afterimage occurred while the temporary afterimage is removed and the colour
pattern is operating.
White Wash
White wash removes permanent images from the screen.
Note: An excessive permanent image may be impossible to clear entirely with White Wash.
OPTION
Move
OK
: English
Input Label
OPTION
Input Label
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Set ID
:1
Set ID
:1
ISM Method
Normal
:: Normal
ISM Method
:: Normal
Normal
Demo Mode : Off
Demo Mode : Off
: Home Use
Mode Setting
▼
1
Select OPTION.
2
OK
: English
SIMPLINK
Mode Setting
: Home Use
▼
Normal
Normal
Orbiter
Colour Wash
White Wash
• If you do not need this function, set Normal.
Select ISM Method.
3
4
Move
Menu Language
PICTURE CONTROL
Menu Language
Select Normal, Orbiter, Colour Wash or White Wash.
Save.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
59
PICTURE CONTROL
DEMO MODE
Use it to see the difference between XD Demo on and XD Demo off.
It is not possible to use Demo Mode in Home Use mode.
In Store Demo, Demo Mode is automatically set to On.
OPTION
Move
OPTION
OK
▼
: English
Menu Language
Input Label
PICTURE CONTROL
2
3
4
60
OK
: English
Input Label
SIMPLINK
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Set ID
:1
Set ID
:1
ISM Method
: Normal
ISM Method
: Normal
Off
Demo Mode
:: On
On
Demo Mode
Mode
Demo
:On
On
On(LED
On)
Mode Setting
: Store Demo
Mode Setting
: Store Demo
Off
1
Move
▼
Menu Language
On
Select OPTION.
Select Demo Mode.
Select On or Off
To stop the Demo Mode, press any button.
MODE SETTING
We recommend setting the TV to “Home Use ” mode for the best picture in your home environment.
“Store Demo ” mode is an optimal setting for displaying at stores.
OPTION
Move
Mode setting
OK
▼
Menu Language
: English
Selecting the environment.
Input Label
SIMPLINK
: On
Key Lock
: Off
Set ID
:1
ISM Method
: Normal
Demo Mode
: On
ModeSetting
Setting
Mode
Choose the setting mode you want.
Store Demo
Home Use
Select [Home Use] to use this TV at home. To use this TV at
store, select [Store Demo].
HomeDemo
Use
: Store
OK
Select OPTION.
2
Select Mode Setting.
3
4
PICTURE CONTROL
1
Select Store Demo or Home Use.
Save.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
61
SOUND & LANGUAGE CONTROL
AUTO VOLUME LEVELER
Auto Volume automatically remains on the same level of volume if you change programmes.
Because each broadcasting station has its own signal conditions, volume adjustment may be needed
every time the channel is changed. This feature allows users to enjoy stable volume levels by making
automatic adjustments for each programme.
AUDIO
Auto
Auto Volume
Volume
Move
Clear Voice II
: Off
• Level
Balance
Auto
AutoVolume
Volume
2
SOUND & LANGUAGE CONTROL
3
Move
: Off
Clear Voice II
: Off
3
-
+
• Level
0
L
R
Balance
On
On
3-
+
0L
R
: Standard
• Infinite Sound : Off
• Infinite Sound : Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
: Standard
OK
Off
Sound Mode
Sound Mode
▼
1
AUDIO
OK
: Off
▼
Select AUDIO.
Select Auto Volume.
Select On or Off.
4
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
62
CLEAR VOICE II
By differentiating the human sound range from others, it helps users listen to human voices better.
AUDIO
Move
Auto Volume
AUDIO
OK
: Off
Clear
Clear Voice
Voice II
II
: :Off
Off
• Level
Balance
3
-
+
0
L
R
3
Clear Voice
Voice II
II
Clear
:: Off
Off
• Level
Off
Off
On3
0
Sound Mode
: Standard
• Infinite Sound : Off
• Infinite Sound : Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
Sound Mode
: Standard
OK
-
+
L
R
▼
• If you select “On” for Clear Voice II,
Select AUDIO.
Infinite Sound feature will not work.
Select Clear Voice II.
Select On or Off.
ADJUSTMENT FOR CLEAR VOICE LEVEL WITH SELECTING ON
4
5
• Select levels from ‘-6’ to ’+6’.
Select Level.
Make desired adjustment.
SOUND & LANGUAGE CONTROL
2
: Off
Balance
▼
1
Move
Auto Volume
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
63
SOUND & LANGUAGE CONTROL
PRESET SOUND SETTINGS-SOUND MODE
You can select your preferred sound setting; Standard, Music, Cinema, Sport or Game and you can
also adjust the Treble, Bass.
Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate sound options based on the programme content.
Standard, Music, Cinema, Sport and Game are preset for optimum sound quality at the factory.
Standard
Music
Cinema
Sport
Game
Offers standard-quality sound.
Optimizes sound for listening to music.
Optimizes sound for watching movies.
Optimizes sound for watching sports events.
Optimizes sound for playing games.
AUDIO
Auto Volume
Move
AUDIO
OK
: Off
Clear Voice II
: Off
• Level
Balance
Auto Volume
Clear Voice II
: Off
3
-
+
• Level
0
L
R
Balance
Sound Mode
Sound
:: Standard
Standard
• Infinite Sound : Off
Sound Mode
• Treble
50
• Bass
50
▼
SOUND & LANGUAGE CONTROL
1
2
3
Move
Select AUDIO.
OK
: Off
3
-
+
0
L
R
: :Standard
Standard
Standard
Standard
• Infinite Sound : Music
Off
• Treble
• Bass
▼
50
Cinema
50
Sport
Game
• You can also adjust Sound Mode in the Q.
Menu.
Select Sound Mode.
Select Standard, Music, Cinema, Sport or Game.
4
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
64
SOUND SETTING ADJUSTMENT -USER MODE
Adjusting the audio equalizer
AUDIO
Move
Auto Volume
Clear Voice II
: Off
• Level
Balance
Sound Mode
AUDIO
OK
Auto Volume
: Off
Clear Voice II
: Off
3
-
+
• Level
0
L
R
Balance
Sound Mode
: Standard
2
3
4
5
OK
3
-
+
0 LL
R
: Standard
• Infinite Sound : Off
• Infinite Sound : Off
• Infinite Sound
• Treble
50
• Treble
50
• Treble
50 ◄
• Bass
50
• Bass
50
• Bass
50
▼
▼
1
Move
: Off
Off
►
Close
Select AUDIO.
Select Sound Mode.
Select Standard, Music, Cinema, Sport or Game.
Select Treble or Bass.
Set the desired sound level.
INFINITE SOUND
Select this option to sound realistic.
1
2
3
Select AUDIO.
Select Infinite sound.
• Infinite Sound : Infinite Sound is a patented
LG proprietary sound processing technology
that strives immersive 5.1 surround sound
impression with front two loudspeakers.
SOUND & LANGUAGE CONTROL
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
Select On or Off.
65
SOUND & LANGUAGE CONTROL
BALANCE
You can adjust the sound balance of the speakers to preferred levels.
AUDIO
Move
AUDIO
OK
Auto Volume
: Off
Auto Volume
Clear Voice II
: Off
Clear Voice II
: Off
• Level
+
• Level
R
Balance
Balance
Balance
Balance
3
-
0 LL
2
SOUND & LANGUAGE CONTROL
3
OK
: Off
3 L-
Balance
L0 L
Sound Mode
: Standard
Sound Mode
: Standard
• Infinite Sound : Off
• Infinite Sound : Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
▼
1
Move
0
R
R+
◄
R
L
R
Close
▼
Select AUDIO.
Select Balance.
Make desired adjustment.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
66
►
TV SPEAKERS ON/ OFF SETUP
You can adjust the TV internal speaker status.
In AV COMPONENT, RGB and HDMI with HDMI to DVI cable, the TV speaker can be operational even
when there is no video signal.
If you wish to use an external Hi-Fi system, turn off the TV’s internal speakers.
Move
AUDIO
OK
▼
: Level
Balance 3
-
+
0
-
+
Balance Sound Mode
: Standard
• Infinite Sound : Off
• Treble
50
• Bass
50
• Reset
TV Speaker
::On
On
1
2
OK
: Level
3
-
+
0
-
+
Sound Mode
: Standard
• Infinite Sound : Off
• Treble
50
• Bass
50
• Reset
TV Speaker
::On
On
Off
On
On
Select AUDIO.
Select TV Speaker.
Select On or Off.
4
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
! NOTE
SOUND & LANGUAGE CONTROL
3
Move
▼
AUDIO
►►When the TV speaker is turned off while the Simplink home theater is operating, the sound output automatically switches to the Home theater speaker, but when the TV speaker is turned on, the sound output the
TV speaker.
?
67
SOUND & LANGUAGE CONTROL
AUDIO RESET
Settings of the selected Sound Mode return to the default factory settings.
AUDIO
Move
AUDIO
OK
Move
▼
: Level
Balance 1
2
SOUND & LANGUAGE CONTROL
3
▼
OK
3
-
+
0
-
+
Balance Sound Mode
: Standard
• Infinite Sound : Off
: Level
Sound Mode
3
-
+
0
-
+
: Standard
• Infinite Sound : Off
Resetting sound mode configuration...
• Treble
50
• Treble
50
• Bass
50
• Bass
50
Reset
•• Reset
• Reset
TV Speaker
: On
TV Speaker
: On
Select AUDIO.
Select Reset.
Initialize the adjusted value.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
68
I/II
STEREO/DUAL RECEPTION (IN ANALOGUE MODE ONLY)
When a programme is selected, the sound information for the station appears with the programme
number and station name.
1
2
Select Audio.
Select the sound output.
Broadcast
On Screen Display
Mono
MONO
Stereo
STEREO
Dual
DUAL I, DUAL II, DUAL I+II
■■ Language selection for dual language broadcast
If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL
II or DUAL I+II.
DUAL ISends the primary broadcast language to the loudspeakers.
DUAL IISends the secondary broadcast language to the loudspeakers.
DUAL I+II Sends a separate language to each loudspeaker.
SOUND & LANGUAGE CONTROL
■■ Mono sound selection
If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the clarity of sound is improved.
69
SOUND & LANGUAGE CONTROL
NICAM RECEPTION
If the TV is equipped with a receiver for NICAM reception, high quality NICAM (Near Instantaneous
Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the type of broadcast received.
1
When NICAM mono is received, you can select NICAM MONO or FM MONO.
2
When NICAM stereo is received, you can select NICAM STEREO or FM MONO.
If the stereo signal is weak, switch to FM MONO.
3
When NICAM dual is received, you can select NICAM DUAL I, NICAM DUAL II or NICAM
DUAL I+II or FM MONO.
SPEAKER SOUND OUTPUT SELECTION
SOUND & LANGUAGE CONTROL
70
In AV, Component, RGB and HDMI mode, you can select output sound for the left and right loudspeakers.
Select the sound output.
L+R: Audio signal from audio L input is sent to the left loudspeaker and audio signal from audio R input
is sent to the right loudspeaker.
L+L: Audio signal from audio L input is sent to left and right loudspeakers.
R+R: Audio signal from audio R input is sent to left and right loudspeakers.
ON-SCREEN MENU LANGUAGE SELECTION
The installation guide menu appears on the TV screen when it is switched on for the first time.
1
Select your desired language.
* If you want to change Language/ Country selection
1
Select OPTION.
2
Select Menu Language.
3
Select your desired language.
Save.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
SOUND & LANGUAGE CONTROL
4
! NOTE
►►If you do not finish the set-up Installation Guide by pressing BACK or if you time out on the OSD (On Screen
Display) the installation menu will continuously appear until the set up is completed whenever the TV is
switched on.
?
71
TIME SETTING
CLOCK SETUP
You must set the time correctly before using on/off timer function.
If current time setting is erased by a power failure or the TV is unplugged, reset the clock.
TIME
Move
OK
Clock
Clock
TIME
Move
Clock
Clock
Off Time
: Off
Off Time
: Off
On Time
: Off
On Time
: Off
Sleep Timer
: Off
Sleep Timer
: Off
OK
Hour
16
Minute
09
Close
1
TIME SETTING
2
3
4
Select TIME.
Select Clock.
Select Hour or Minute.
Set the Hour or Minute.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
72
AUTO ON/OFF TIME SETTING
The Off time function automatically switches the TV to standby at a preset time.
Two hours after the TV is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed.
The Off time function overrides the On timer function if both are set to the same time.
The TV must be in standby mode for the On timer to work.
TIME
Move
TIME
OK
Clock
Move
OK
Clock
Off Time
: Off
Off Time
On Time
:: Off
On
On Time
Sleep Timer
: Off
Sleep Timer
23:59
: Off
Off
:: Off
Hour: Off
◄
On
►
00
Minute
00
Programme
1
Volume
30
Close
1
2
Select TIME.
Select Off Time or On Time.
3
4
Select Hour, Minute, Programme or Volume.
TIME SETTING
When the On Time is selected
Set the hour, Minute, Programme, Volume.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
73
TIME SETTING
SLEEP TIMER SETTING
You do not have to remember to switch the TV off before you go to sleep.
The sleep timer automatically switches the TV to standby after the preset time has elapsed.
1
Select Sleep Timer.
2
Select Off, 10, 20, 30, 60, 90, 120, 180 or 240 min.
•W
hen you switch the TV off, the preset sleep timer is cancelled.
•Y
ou can also adjust Sleep Timer in the TIME menu.
TIME SETTING
74
TELETEXT
This feature is not available in all countries.
Teletext is a free service broadcast by most TV stations which gives up-tothe-minute information on news, weather, television programmes, share
prices and many other topics.
The teletext decoder of this TV can support the SIMPLE, TOP and
FASTEXT systems. SIMPLE (standard teletext) consists of a number of
pages which are selected by directly entering the corresponding page
number. TOP and FASTEXT are more modern methods allowing quick
and easy selection of teletext information.
SWITCH ON/OFF
Press the TEXT button to switch to teletext. The initial page or last page
viewed appears on the screen.
Two page numbers, TV station name, date and time are displayed on the
screen headline. The first page number indicates your selection, while the
second shows the current page displayed.
Press the TEXT button to switch off teletext. The previous mode reappears.
SIMPLE TEXT
■■ Page selection
1
Enter
the desired page number as a three digit number with the NUMBER buttons. If during selection
you press a wrong number, you must complete the three digit number and then re-enter the correct
page number.
2
The P∧∨ button can be used to select the preceding or following page.
TOP TEXT
The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow
field denotes the next group and the blue field indicates the next block.
1 With the blue button you can progress from block to block.
2 Use the yellow button to proceed to the next group with automatic overflow to the next block.
3 With the green button you can proceed to the next existing page with automatic overflow to the next
group.
4 Alternatively the P ∧ button can be used.
The red button returns to the previous selection. Alternatively the P ∨ button can be used.
TELETEXT
■■ Block / group / page selection
■■ Direct page selection
As with SIMPLE teletext mode, you can select a page by entering it as a three digit number using the
NUMBER buttons in TOP mode.
75
TELETEXT
FASTEXT
The teletext pages are colour coded along the bottom of the screen and are selected by pressing the
corresponding coloured button.
■■Page selection
1
2
3
4
Press the T.OPT button and then use ∧∨ button to select i menu. Display the index page.
You can select the pages which are colour coded along the bottom line with corresponding coloured
buttons.
AS with SIMPLE teletext mode, you can select a page by entering its three digit page number with
the NUMBER buttons in FASTEXT mode.
The P∧∨ button can be used to select the preceding or following page.
SPECIAL TELETEXT FUNCTIONS
■■ Press the T. OPT button and then use ∧∨ button to select the Text Option menu.
i
Text Option
■■Index
Select the each index page.
■■Time
When viewing a TV programme, select this menu to display the time at the top
right hand corner of the screen.
In the teletext mode, press this button to select a sub page number. The sub page
number is displayed at the bottom of the screen. To hold or change the sub page,
press the RED/GREEN,< > or NUMBER buttons.
Index
Time
Hold
Reveal
Update
Close
TELETEXT
■■ Hold
Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages.
The number of sub pages and the sub page displayed is, usually, shown on the screen below the time.
When this menu is selected the stop symbol is displayed at the top left-hand corner of the screen and
the automatic page change is inactive.
?
■■Reveal
Select this menu to display concealed information, such as solutions to riddles or puzzles.
■■Update
Displays the TV picture on the screen while waiting for a new teletext page. The display will appear at
the top left hand corner of the screen. When the updated page is available then display will change to
the page number. Select this menu again to view the updated teletext page.
76
APPENDIX
TROUBLESHOOTING
APPENDIX
■■ Check to see if there is any object between the TV and the remote control
The TV does not operate properly.
The remote control
does not work
causing an obstruction. Ensure you are pointing the remote control directly
at the TV.
■■ Ensure that the batteries are installed with correct polarity (+ to +, - to -).
■■ Install new batteries.
■■ Is the sleep timer set?
Power is suddenly
■■ Check the power control settings. Has the Power supply been interrupted.
turned off
■■ If the TV is switched on and there is no input signal, it will switch off automatically after 15 minutes.
The video function does not work.
■■ Check whether the TV is switched on.
■■ Try another channel. The problem may be with the broadcast.
No picture & No sound ■■ Is the power cord inserted correctly into the mains?
■■ Check your antenna direction and/or location.
■■ Test the mains outlet by plugging another TV into the same outlet.
Picture appears slowly ■■ This is normal, the image is muted during the TV startup process. Please contact
your service centre, if the picture has not appeared after five minutes.
after switching on
■■ Adjust Colour in menu option.
No or poor colour
or poor picture
■■ Allow a sufficient distance between the TV and the VCR.
■■ Try another channel. The problem may be with the broadcast.
■■ Are the video cables installed properly?
■■ Activate any function to restore the brightness of the picture.
Horizontal/vertical bars
or picture shaking
Poor reception on
some channels
■■ Check for local interference such as an electrical appliance or power tool.
■■ Station or cable channel experiencing problems, tune to another station.
■■ Station signal is weak, reposition the antenna to receive weaker stations.
Lines or streaks
■■ Check for sources of possible interference.
■■ Check antenna (Change the position of the antenna).
in pictures
No picture
■■ Check that your HDMI cable is version 1.3 or higher.
■■ If the HDMI cables don’t support HDMI version 1.3, flickering or no screen display can
result. Please use the latest cables that support at least HDMI version 1.3.
APPENDIX
when connecting
HDMI
77
APPENDIX
The audio function does not work.
■■ Check whether the TV is switched on.
Picture OK & No
sound
No output from one
of the speakers
Unusual sound from
inside the TV
No sound when connecting HDMI or USB
■■ Press the
+ or - button.
■■ Sound muted? Press MUTE button.
■■ Try another channel. The problem may be with the broadcast.
■■ Are the audio cables installed properly?
■■ Adjust Balance in menu option.
■■ A change in ambient humidity or temperature may result in an unusual noise when
the TV is switched on or off and does not indicate a fault with the TV.
■■ Check HDMI cable over version 1.3.
■■ Check USB cable over version 2.0.
There is a problem in PC mode. (Only PC mode applied)
The signal is out of
range
(Invalid format)
Vertical bar or stripe on
background &
Horizontal Noise &
Incorrect position
Screen colour is
unstable or single
colour
■■ Adjust resolution, horizontal frequency, or vertical frequency.
■■ Check the input source.
■■ Use Auto configure or adjust size, phase, or H/V position. (Option)
■■ Check the signal cable.
■■ Reinstall the PC video card.
There is a problem with PICTURE settings.
When the user changes the picture settings, ■■ It means that the TV is currently set to Store Demo mode.
To switch to Home use mode you should do the followings: From the TV
the TV automatically
Menu, choose OPTION -> Choose Mode Setting -> Choose Home use.
converts back to the
Now, you have completed switching to the Home use mode.
initial settings after a
certain period of time.
APPENDIX
78
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV.
Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning.
CLEANING THE SCREEN
1
A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it is almost
dry, and then use it to wipe the screen.
2
Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before
switching on.
CLEANING THE CABINET
!
■■ To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
■■ Do not to use a wet cloth.
?
EXTENDED ABSENCE
CAUTION
►►If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power cord to
protect against possible damage from lightning or power surges.
APPENDIX
79
APPENDIX
PRODUCT SPECIFICATIONS
42PJ2***
50PJ2***
42PJ250R-TA
42PJ251R-TB
50PJ250R-TA
with stand
988.0 mm x 678.7 mm x 260.0 mm
1171.4 mm x 781.8 mm x 309.7 mm
without stand
988.0 mm x 617.8 mm x 55.3 mm
1171.4 mm x 720.9 mm x 55.3 mm
with stand
without stand
21.6 kg
30.0 kg
20.0 kg
27.6 kg
42PJ3***
50PJ3***
42PJ350R-TA
50PJ350R-TA
with stand
988.0 mm x 678.7 mm x 260.0 mm
1171.4 mm x 781.8 mm x 309.7 mm
without stand
988.0 mm x 617.8 mm x 55.3 mm
1171.4 mm x 720.9 mm x 55.3 mm
with stand
without stand
21.6 kg
30.0 kg
20.0 kg
27.6 kg
MODELS
Dimensions
(Width x Height x
Depth)
Weight
MODELS
Dimensions
(Width x Height x
Depth)
Weight
Television System
PAL/SECAM B/G/D/K, PAL I/II, NTSC-M
Programme Coverage
VHF: NZ1 to E21, UHF: E21 to E69, CATV: S1 to S20, HYPER: S21 to S47
External Antenna Impedance
Operating Temperature
Environment condition
Supported movie files
75 Ω
0 °C to 40 °
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Refer to p. 42
■ ■ The specifications shown above may be changed without prior notice for quality improvement.
■ ■ For the power supply and power consumption refer to the label attached to the product.
APPENDIX
80
42PJ5***
50PJ5***
42PJ560R-TA
50PJ560R-TA
with stand
1105.0 mm x 682.7 mm x 260.0 mm
1286.7 mm x 781.8 mm x 309.7 mm
without stand
1105.0 mm x 621.8 mm x 60.0 mm
1286.7 mm x 720.9 mm x 60.0 mm
with stand
without stand
24.6 kg
33.0 kg
23.0 kg
30.6 kg
42PJ6***
50PJ6***
42PJ650R-TA
50PJ650R-TA
with stand
999.6 mm x 683.2 mm x 260.0 mm
1184.0 mm x 801.0 mm x 309.7 mm
without stand
999.6 mm x 625.3 mm x 52.4 mm
1184.0 mm x 730.0 mm x 52.4 mm
with stand
without stand
24.2 kg
32.0 kg
22.5 kg
29.6 kg
MODELS
Dimensions
(Width x Height x
Depth)
Weight
MODELS
Dimensions
(Width x Height x
Depth)
Weight
Television System
PAL/SECAM B/G/D/K, PAL I/II, NTSC-M
Programme Coverage
VHF: NZ1 to E21, UHF: E21 to E69, CATV: S1 to S20, HYPER: S21 to S47
External Antenna Impedance
Operating Temperature
Environment condition
Supported movie files
75 Ω
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Refer to p. 42
■■ The specifications shown above may be changed without prior notice for quality improvement.
■■ For the power supply and power consumption refer to the label attached to the product.
APPENDIX
81
APPENDIX
50PK5***
60PK5***
50PK550R-TA
60PK550R-TA
with stand
1171.4 mm x 786.2 mm x 309.7mm
1392.0 mm x 915.0 mm x 384.0 mm
without stand
1171.4 mm x 724.4 mm x 55.3mm
1392.0 mm x 852.0 mm x 55.3 mm
with stand
without stand
31.0kg
45.9 kg
28.6kg
41.4 kg
MODELS
Dimensions
(Width x Height x
Depth)
Weight
Television System
PAL/SECAM B/G/D/K, PAL I/II, NTSC-M
Programme Coverage
VHF: NZ1 to E21, UHF: E21 to E69, CATV: S1 to S20, HYPER: S21 to S47
External Antenna Impedance
Operating Temperature
Environment condition
Supported movie files
75 Ω
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Refer to p. 42
■■ The specifications shown above may be changed without prior notice for quality improvement.
■■ For the power supply and power consumption refer to the label attached to the product.
APPENDIX
82
IR CODES
*This feature is not available for all models.
Code (Hexa)
Function
Note
08
POWER
R/C BUTTON
95
Energy Saving
R/C BUTTON
0B
INPUT
R/C BUTTON
0F
TV
R/C BUTTON
45
Q.MENU
R/C BUTTON
43
MENU
R/C BUTTON
7C
R/C BUTTON
40
Up (∧)
R/C BUTTON
41
Down (∨)
R/C BUTTON
07
Left (<)
R/C BUTTON
06
Right (>)
R/C BUTTON
44
OK (⊙)
R/C BUTTON
28
BACK (
30
AV MODE
)
R/C BUTTON
R/C BUTTON
02
+
R/C BUTTON
03
-
R/C BUTTON
1E
FAV ( MARK )
R/C BUTTON
79
RATIO
R/C BUTTON
09
MUTE
R/C BUTTON
00
P∧
R/C BUTTON
01
10 to 19
53
P∨
R/C BUTTON
Number Key 0 to 9
R/C BUTTON
LIST
R/C BUTTON
1A
Q.VIEW
R/C BUTTON
72
RED Key
R/C BUTTON
71
GREEN Key
R/C BUTTON
63
YELLOW Key
R/C BUTTON
61
BLUE Key
R/C BUTTON
20
TEXT
R/C BUTTON
21
T.OPT(T.Option)
R/C BUTTON
7E
R/C BUTTON
EXIT
R/C BUTTON
B1
▀
R/C BUTTON
B0
►
R/C BUTTON
BA
l l (FREEZE)
R/C BUTTON
8F
◄◄
R/C BUTTON
8E
►►
R/C BUTTON
5E
CLEAR VOICE 2
R/C BUTTON
APPENDIX
5B
83
APPENDIX
EXTERNAL CONTROL DEVICE SETUP
RS-232C SETUP
Connect the RS-232C (serial port) input jack to an
external control device (such as a computer or an
A/V control system) to control the product’s functions externally.
Connect the serial port of the control device to the
RS-232C jack on the product back panel.
Note:
RS-232C connection cables are not supplied with
the product.
In USB, it doesn’t support RS-232C function.
TYPE OF CONNECTOR; D-SUB 9-PIN MALE
No.
1
2
3
4
5
6
7
8
9
Pin Name
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
1
5
6
9
RS-232C CONFIGURATIONS
3-Wire Configurations(Not standard)
7-Wire Configurations (Standard RS-232C cable)
APPENDIX
84
RXD TXD
GND
DTR
DSR
RTS
CTS
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
RXD TXD
GND
DTR
DSR
RTS
CTS
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
SET ID
Use this function to specify a set ID number.
Refer to ‘Real Data Mapping’. ► p.89
OPTION
Menu Language
Move
OK
: English
2
3
Menu Language
Move
OK
: English
Input Label
Input Label
1
OPTION
SIMPLINK
: On
SIMPLINK
Key Lock
: Off
Key Lock
: On
Set ID
::11
Set ID
ISM Method
: Normal
ISM Method
: Normal
Demo Mode
: Off
Demo Mode
: Off
Mode Setting
: Store Demo
Mode Setting
: Store Demo
: Off
◄
::11
1
►
Close
Select OPTION.
Select Set ID.
Adjust Set ID to choose the desired TV ID number.
The adjustment range of SET ID is 1 to 99.
APPENDIX
• Press BACK to move to the previous menu screen.
85
APPENDIX
COMMUNICATION PARAMETERS
■■ Baud rate : 9600 bps (UART)
■■ Data length : 8 bits
■■ Parity : None
■■ Stop bit : 1 bit
■■ Communication code : ASCII code
■■ Use a crossed (reverse) cable.
Command Reference List
01. Power
COMMAND
1
COMMAND
2
DATA
(Hexadecimal)
k
a
00 to 01
COMMAND
1
COMMAND
2
DATA
(Hexadecimal)
14. Colour Temperature
x
u
00 to 64
02. Aspect Ratio
k
c
Refer to p. 87
15. Treble
k
r
00 to 64
03. Screen Mute 85
k
d
Refer to p. 87
16. Bass
k
s
00 to 64
04. Volume Mute
k
e
00 to 01
17. Abnormal Status
k
z
FF
05. Volume Control
k
f
00 to 64
18. ISM Method
j
p
Refer to p. 89
06. Contrast
k
g
00 to 64
19. Auto Configure
j
u
01
07. Brightness
k
h
00 to 64
20. Eneregy Saving
j
q
Refer to p. 89
08. Colour
k
i
00 to 64
21. Tune Command
m
a
Refer to p. 90
09. Tint
k
j
00 to 64
22. Channel Skip
m
b
00 to 01
10. Sharpness
k
k
00 to 64
23. Key
m
c
Refer to p. 83
11. OSD Select
k
l
00 to 01
24. Input select (Main)
x
b
Refer to p. 91
12. Remote Control Lock
/ Key Lock Mode
k
m
00 to 01
13. Balance
k
t
00 to 64
Transmission / Receiving Protocol
APPENDIX
86
Transmission
OK Acknowledgement
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command2][ ][Set ID][ ][OK][Data][x]
* [Command 1] : First command to control the set.
(j, k, m or x)
* [Command 2] : Second command to control the set.
: You can adjust the set ID to choose
* [Set ID]
desired TV ID number in Setup menu.
Adjustment range is 1 to 99.
When selecting Set ID ‘0’, every connected TV is controlled. Set ID is indicated as decimal (1 to 99) on menu and
as Hexa decimal (0x0 to 0x63) on transmission/receiving protocol.
: To transmit command data.
* [DATA] Transmit ‘FF’ data to read status of
command.
[Cr]
:
Carriage
Return
*
ASCII code ‘0x0D’
: ASCII code ‘space (0x20)’
* [ ]
* The TV transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time,
if the data is data read mode, it indicates present
status data. If the data is data write mode, it returns
the data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
TV transmits ACK(acknowledgement) based on this
format when receiving abnormal data form non-viable
functions or communication errors.
[Command 2] : use as command.
[Set ID]: use the small character, if set ID is 10, TV will
send the ‘0’, ‘a’
[Data]: use the small character, if data is 0xab, TV will
send the ‘a’, ‘b’.
[NG]: use the large character.
01. Power (Command: k a)
►► To control Power On/Off of the TV.
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data00 : Power Off
01 : Power On
Acknowledgement
04. Volume Mute (Command: k e)
►► To control volume mute on/off.
You can also adjust mute using the MUTE button
on remote control.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Acknowledgement
[a][ ][Set ID][ ][OK/NG][Data][x]
►► To show Power On/Off.
Transmission
[e][ ][Set ID][ ][OK/NG][Data][x]
[k][a][ ][Set ID][ ][FF][Cr]
Acknowledgement
[a][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
* If there is the time delay between command and ack
message during power on sequence, It should
be described like “Note: In this model, TV will send
the Acknowledge after power on processing completion.There might be a time delay between command and acknowledge.”
►► To adjust volume.
You can also adjust volume with the VOLUME
buttons on remote control.
Transmission
02. Aspect Ratio (Command: k c) (Main Picture Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the
Aspect Ratio in the PICTURE menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen (4:3)
02 : Wide screen (16:9)
04 : Zoom
10 to 1F : Cinema Zoom 1 to 16
Acknowledgement
Data 06 : Original
07 : 14 : 9
09 : Just Scan
[c][ ][Set ID][ ][OK/NG][Data][x]
* Using the RGB-PC, Component or HDMI input, you
select either 16:9 or 4:3 screen aspect ratio.
* In HDMI/Component (over 720p)mode, Just Scan is
available.
[k][f][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 89.
Acknowledgement
[f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 89.
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
[k][d][ ][Set ID][ ][Data][Cr]
Data00 : Screen mute off (Picture/Panel on)
01 : Screen mute on (Panel off)
10 : Video mute on (Picture Off)
[k][h][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 89.
Acknowledgement
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x]
[d][ ][Set ID][ ][OK/NG][Data][x]
* In case of Video-Out mute on only, TV will display On
Screen Display(OSD) But, In case of Screen Mute
On, TV will not display OSD.
APPENDIX
►► To select screen mute on/off.
Transmission
07. Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission
03. Screen Mute (Command: k d)
87
APPENDIX
08. Colour (Command: k i)
►► To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 89.
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
09. Tint (Command: k j)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
DataRed : 00 to Green : 64
* Refer to ‘Real data mapping 1’. See page 89.
Acknowledgement
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data00 : Lock off
Acknowledgement
01 : Lock on
[m][ ][Set ID][ ][OK/NG][Data][x]
13. Balance (Command: k t)
►► To adjust balance.
You can also adjust balance. in the AUDIO menu.
Transmission
[k][r][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 89.
Acknowledgement
[t][ ][Set ID][ ][OK/NG][Data][x]
[j][ ][Set ID][ ][OK/NG][Data][x]
14. Colour Temperature (Command: x u)
10. Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission
►► To adjust colour temperature.
You can also adjust Colour Temperature in the
PICTURE menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data W50 : 00 to C50 : 64
Acknowledgement
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 89.
Acknowledgement
[x][u][ ][Set ID][ ][Data][Cr]
[u][ ][Set ID][ ][OK/NG][Data][x]
[k][ ][Set ID][ ][OK/NG][Data][x]
15. Treble (Command: k r)
11. OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
Acknowledgement
01 : OSD on
►► To adjust Treble.
Transmission
[k][r][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 89.
Acknowledgement
[r][ ][Set ID][ ][OK/NG][Data][x]
[l][ ][Set ID][ ][OK/NG][Data][x]
16. Bass (Command: k s)
APPENDIX
88
12. Remote control lock / Key Lock Mode
(Command: k m)
►► To lock the remote control and the front panel controls
on the set. (If you’re not using the remote control and front panel
controls on the TV, use this mode. When main power
is on/off, remote control lock is released.)
►► To adjust bass
Transmission
[k][s][ ][Set ID][ ][Data][Cr]
Data Min: 00 to Max: 64
* Refer to ‘Real data mapping 1’. See page 89.
Acknowledgement
[s][ ][Set ID][ ][OK/NG][Data][x]
17. Abnormal State (Command: k z)
19 . Auto Configure (Command: j u)
►►To recognize an abnormal state.
Transmission
[k][z][ ][Set ID][ ][Data][Cr]
►► To adjust picture position and minimize image shaking
automatically. It works only in RGB (PC) mode.
Transmission
Acknowledgement
[j][u][ ][Set ID][ ][Data][Cr]
[z][ ][Set ID][ ][OK/NG][Data][x]
Data FF: Read
Data01: To set
Acknowledgement
Data 00: Normal (Power on and signal exist)
[u][ ][Set ID][ ][OK/NG][Data][x]
Data 01: No signal (Power on)
Data 02: Turn the TV off by remote control
Data 03: Turn the TV off by sleep time function
Data 04: Turn the TV off by RS-232C function
20. Energy Saving (Command: j q)
Data 05: 5V down
Data 06: AC down
►► To reduce the power consumption of the TV.
Transmission
Data 08: Turn the TV off by Off time function
[j][q][ ][Set ID][ ][Data][Cr]
Data 09: Turn the TV off by Auto off function
Data 00: Low Power Off
* This function is “read only”.
Data 01: Low Power Minimum
Data 02: Low Power Medium
Data 03: Low Power Maximum
18. ISM Method (Command: j p)
►► To avoid having a fixed image remain on screen.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
MSB
Data 05: Screen Off
Data 10: Intelligent Sensor
LSB
0
0
0
0
0
0
0
0
Acknowledgement
[q][ ][Set ID][ ][OK/NG][Data][x]
Orbiter
White Wash
Normal
Colour Wash
7
6
5
1
4
0
3
2
1
0
Function
0
0
1
0
Orbiter
0
1
0
0 White Wash
1
0
0
0
0
0
0
0 Colour Wash
Data 02: Orbiter
Data 04: White Wash
Data 08: Normal
Data 20: Colour Wash
* More two kinds of function can not be set at a time.
Acknowledgement
[p][ ][Set ID][ ][OK/NG][Data][x]
A:
Step 10
F:
10 :
Step 15
Step 16
64 :
Step 100
* Real data mapping 2
00 : -30
01 : -29
02 : -28
1E : 0
28 :
6E : Step 110
73 :
74 :
Step 115
Step 116
C7 : Step 199
FE : Step 254
FF : Step 255
+0
3A : +28
3B : +29
3C : +30
4E : N/A
4F : N/A
50 : N/A
APPENDIX
Normal
* Real data mapping 1
00 : Step 0
89
APPENDIX
21. Tune Command/ Channel Tuning (Command: m a)
►► Tune Channel to following Physical number.
Transmission
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
Data0, Data1: Programme Number
Data0: High byte
Data1: Low byte
Data2: Attribute
Air
7
Reserved
6
5
4
Reserved
Reserved
Reserved
0
x
0
0
ATV
0
x
0
1
DTV
0
x
1
0
Radio
0
x
1
1
Reserved
RF Source
3
2
1
0
Reserved
Reserved
Reserved
Data
Main / Sub
x
x
x
0
Main picture
x
x
x
1
Sub picture
Cable
7
Reserved
6
5
4
Reserved
Reserved
Reserved
1
x
0
0
2
1
Reserved
Reserved
Data
Main / Sub
ATV
x
x
x
0
Main picture
x
x
x
1
Sub picture
1
x
0
1
DTV
1
x
1
0
Radio
1
x
1
1
Reserved
'x' : don't care
Acknowledgement
[a][ ][Set ID][OK][ ][Data0][Data1][x]
[a][ ][Set ID][NG][ ][Data0][x]
22. Channel Skip(Command: m b)
►► To set skip status for the current Programme.
Transmission
[m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip
01 : Add
Acknowledgement
[b][ ][Set ID][ ][OK/NG][Data][x]
23. Key (Command: m c)
APPENDIX
►► To send IR remote key code.
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
Data: Key code - Refer to page 83.
Acknowledgement
[c][ ][Set ID][ ][OK/NG][Data][x]
90
3
Reserved
RF Source
0
24. Input select (Command: x b)
(Main Picture Input)
►► To select input source for TV.
Transmission
[x][b][ ][Set ID][ ][Data][Cr]
Data : Structure
MSB
0
LSB
0
0
0
External Input
External Input
0
0
0
0
Input Number
Data
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB-PC
1
0
0
1
HDMI
INPUT Number
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Acknowledgement
[b][ ][Set ID][ ][OK /NG][Data][x]
APPENDIX
91
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
Model :
Serial No. :
Download PDF