OWNER’S MANUAL PLASMA TV Please read this manual carefully before operating your set and retain it for future reference. PM69** P/NO : MFL67500921 (1210-REV02) Printed in Korea www.lg.com 2 TABLE OF CONTENTS ENGLISH ENG TABLE OF CONTENTS 3 LICENSES 33 PENTOUCH 3 OPEN SOURCE SOFTWARE NOTICE 33 34 34 Using Pentouch - Using the Pentouch Function - Pairing between Touch Pen 4 SAFETY INSTRUCTIONS 10 - Viewing 3D Imaging (Only 3D models) 37 MAINTENANCE 12 INSTALLATION PROCEDURE 37 37 37 Cleaning your TV - Screen, frame, cabinet and stand - Power cord 12 ASSEMBLING AND PREPARING 38 TROUBLESHOOTING 12 16 17 18 19 19 21 22 23 Unpacking Separate purchase Parts and buttons Lifting and moving the TV Setting up the TV - Attaching the stand Mounting on a table Mounting on a wall Tidying cables 38 EXTERNAL CONTROL DEVICE SETUP 39 ENVIRONMENTAL INFORMATION 40 SPECIFICATIONS 24 MAKING CONNECTIONS 24 25 26 26 27 27 28 28 28 Antenna Connection HDMI Connection DVI to HDMI Connection RGB-PC Connection Component Connection Composite Connection Audio Connection - Digital optical audio connection USB Connection 29 REMOTE CONTROL 30 MAGIC REMOTE CONTROL FUNCTIONS 31 31 31 32 Registering Magic Remote Control How to use Magic Remote Control Precautions to Take when Using the Magic Remote Control USING THE USER GUIDE WARNING yy If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. CAUTION yy If you ignore the caution message, you may be slightly injured or the product may be damaged. NOTE yy The note helps you understand and use the product safely. Please read the note carefully before using the product. LICENSES / OPEN SOURCE SOFTWARE NOTICE 3 Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or y registered trademarks of HDMI Licensing LLC. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX video. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod. divx.com for more information on how to complete your registration. “DivX Certified® to play DivX® video up to HD 1080p, including premium content.” “DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.” “Covered by one or more of the following U.S. patents : 7,295,673; 7,460,668; 7,515,710; 7,519,274” Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the Symbol & DTS and the Symbol together are registered trademarks & DTS 2.0+Digital Out is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved. OPEN SOURCE SOFTWARE NOTICE To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com . In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to firstname.lastname@example.org. This offer is valid for three (3) years from the date on which you purchased the product. ENGLISH ENG LICENSES 4 SAFETY INSTRUCTIONS ENGLISH ENG SAFETY INSTRUCTIONS Please read these safety precautions carefully before using the product. WARNING Do not place the TV and remote control in the following environments: yy --A location exposed to direct sunlight --An area with high humidity such as a bathroom --Near any heat source such as stoves and other devices that produce heat --Near kitchen counters or humidifiers where they can easily be exposed to steam or oil --An area exposed to rain or wind --Near containers of water such as vases Otherwise, this may result in fire, electric shock, malfunction or product deformation. Do not place the product where it might be exposed to dust. y yy This may cause a fire hazard. Mains plug is the disconnecting device. The plug must remain readily operable. yy Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or yy covered with dust, dry the power plug completely or wipe dust off. y You may be electrocuted due to excess moisture. Make sure to connect the power cable to the grounded current. (Except for devices yy which are not grounded.) You may be electrocuted or injured. Fix the power cable completely. y yy If the power cable is not fixed completely, a fire can break out. Ensure the power cord does not come into contact with hot objects such as a yy heater. y This may cause a fire or an electric shock hazard. Do not place a heavy object, or the product itself, on power cables. y yy Otherwise, this may result in fire or electric shock. Bend antenna cable between inside and outside building to prevent rain from yy flowing in. y This may cause water damaged inside the Product and could give an electric shock. When mounting a TV it on the wall, make sure not to install TV by hanging power yy and signal cables on the back of the TV. y It may cause fire, electric shock. SAFETY INSTRUCTIONS Do not drop the product or let it fall over when connecting external devices. y yy Otherwise, this may result in injury or damage to the product. Des icca nt Keep the packing anti-moisture material or vinyl packing out of the reach of yy children. y Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children. Do not let your children climb or cling onto the TV. y yy Otherwise, the TV may fall over, which may cause serious injury. Dispose of used batteries carefully to protect a child from eating them. y yy Please seek Doctor- Medical Attention immediately if child consumes batteries. Do not insert any metal objects/conductors (like a metal chopstick/cutlery/ yy screwdriver) between power cable plug and input Wall Socket while it is connected to the input terminal on the wall. Additionally, do not touch the power cable right after plugging into the wall input terminal. y You may be electrocuted.y (Depending on model) Do not put or store inflammable substances near the product. y yy There is a danger of combustion/explosion or fire due to careless handling of the inflammable substances. Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the yy product, or inflammable objects such as paper and matches. Children must pay particular attention. y Electrical shock, fire or injury can occur. If a foreign object is dropped into the product, unplug the power cord and contact the service centre. Do not spray water on the product or scrub with an inflammable substance (thinner yy or benzene). Fire or electric shock accident can occur. Do not allow a impact shock or any objects to fall into the product, and do not drop yy onto the screen with something. y You may be injured or the product can be damaged. Never touch this product or antenna during a thunder or lighting storm. y yy You may be electrocuted. Never touch the wall outlet when there is leakage of gas, open the windows and yy ventilate. y It may cause a fire or a burn by a spark. ENGLISH ENG Do not plug too many electrical devices into a single multiple electrical outlet. y yy Otherwise, this may result in fire due to over-heating. 5 6 SAFETY INSTRUCTIONS ENGLISH ENG Do not disassemble, repair or modify the product at your own discretion. y yy Fire or electric shock accident can occur. y Contact the service center for check, calibration or repair. If any of the following occur, unplug the product immediately and contact your local yy service centre. --The product has been impacted by shock --The product has been damaged --Foreign objects have entered the product --The product produced smoke or a strange smell This may result in fire or electric shock. If you don’t intend to use the product for a long time, unplug the power cable from yy the product. y Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire. Apparatus shall not be exposed to dripping or splashing and no objects filled with yy liquids, such as vases, shall be placed on the apparatus. SAFETY INSTRUCTIONS Install the product where no radio wave occurs. yy There should be enough distance between an outside antenna and power lines to yy keep the former from touching the latter even when the antenna falls. y This may cause an electric shock. Do not install the product on places such as unstable shelves or inclined surfaces. yy Also avoid places where there is vibration or where the product cannot be fully supported. y Otherwise, the product may fall or flip over, which may cause injury or damage to the product. If you install the TV on a stand, you need to take actions to prevent the product yy from overturning. Otherwise, the product may fall over, which may cause injury. If you intend to mount the product to a wall, attach VESA standard mounting interface (optional yy parts) to the back of the product. When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop. Only use the attachments / accessories specified by the manufacturer. yy When installing the antenna, consult a qualified service man. y yy This may create a fire hazard or an electric shock hazard. We recommend that you maintain a distance of at least 2 to 7 times the diagonal yy screen size when watching TV. y If you watch TV for a long period of time, this may cause blurred vision. Only use the specified type of battery. y yy This could cause damage to the remote control. Do not mix new batteries with old batteries. y yy This may cause the batteries to overheat and leak. Make sure there are no objects between the remote control and its sensor. yy Signal from the remote control may be disturbed by sun light or other strong light. yy In this case, darken the room. When connecting external devices such as video game consoles, make sure the yy connecting cables are long enough. y Otherwise, the product may fall over, which may cause injury or damage the product. ENGLISH ENG CAUTION 7 8 SAFETY INSTRUCTIONS ENGLISH ENG Do not turn the product On/Off by plugging-in or unplugging the power plug to the yy wall outlet. (Do not use the power plug for switch.) y It may cause mechanical failure or could give an electric shock. Please follow the installation instructions below to prevent the product from yy overheating. --The distance between the product and the wall should be more than 10 cm. --Do not install the product in a place with no ventilation (e.g., on a bookshelf or in a cupboard). --Do not install the product on a carpet or cushion. --Make sure the air vent is not blocked by a tablecloth or curtain. Otherwise, this may result in fire. Take care not to touch the ventilation openings when watching the TV for long yy periods as the ventilation openings may become hot. This does not affect the operation or performance of the product. Periodically examine the cord of your appliance, and if its appearance indicates damage or yy deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Prevent dust collecting on the power plug pins or outlet. y yy This may cause a fire hazard. Protect the power cord from physical or mechanical abuse, such as being twisted, yy kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not press strongly upon the panel with a hand or sharp object such as nail, yy pencil or pen, or make a scratch on it. Avoid touching the screen or holding your finger(s) against it for long periods of yy time. Doing so may produce some temporary distortion effects on the screen. When cleaning the product and its components, unplug the power first and wipe it yy with a soft cloth. Applying excessive force may cause scratches or discolouration. Do not spray with water or wipe with a wet cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax, benzene, alcohol etc., which can damage the product and its panel. y Otherwise, this may result in fire, electric shock or product damage (deformation, corrosion or breakage). As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power yy source even if you turn off this unit by SWITCH. When unplugging the cable, grab the plug and unplug it. y yy If the wires inside the power cable are disconnected, this may cause fire. When moving the product, make sure you turn the power off first. Then, unplug the yy power cables, antenna cables and all connecting cables. y The TV set or power cord may be damaged, which may create a fire hazard or cause electric shock. SAFETY INSTRUCTIONS Contact the service center once a year to clean the internal parts of the product. y yy Accumulated dust can cause mechanical failure. Refer all servicing to qualified service personnel. Servicing is required when the yy apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. If the product feels cold to the touch, there may be a small “flicker” when it is turned yy on. This is normal, there is nothing wrong with product. The panel is a high technology display product with resolution of two million to six yy million pixels. You may see tiny black dots and/or brightly coloured dots (red, blue or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and does not affect the performance and reliability of the product. y This phenomenon also occurs in third-party products and is not subject to exchange or refund. You may find different brightness and color of the panel depending on your viewing yy position(left/right/top/down). y This phenomenon occurs due to the characteristic of the panel. It is not related with the product performance, and it is not malfunction. Displaying a still image (e.g., broadcasting channel logo, on-screen menu, scene from a video yy game) for a prolonged time may cause damage to the screen, resulting in retention of the image, which is known as image sticking. The warranty does not cover the product for image sticking. y Avoid displaying a fixed image on your television’s screen for a prolonged period (2 or more hours for LCD, 1 or more hours for Plasma). y Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking may occur on the borders of the panel. y This phenomenon also occurs in third-party products and is not subject to exchange or refund. Generated Sound yy “Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to tempera-ture and humidity. This noise is common for products where thermal deformation is required. Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. y This generated sound does not affect the performance and reliability of the product. ENGLISH ENG When moving or unpacking the product, work in pairs because the product is yy heavy. y Otherwise, this may result in injury. 9 10 SAFETY INSTRUCTIONS ENGLISH ENG Viewing 3D Imaging (Only 3D models) WARNING Viewing Environment yy Viewing Time -- When watching 3D contents, take 5 - 15 minute breaks every hour. Viewing 3D contents for a long period of time may cause headache, dizziness, fatigue or eye strain. Those that have a photosensitive seizure or chronic illness yy Some users may experience a seizure or other abnormal symptoms when they are exposed to a flashing light or particular pattern from 3D contents. yy Do not watch 3D videos if you feel nausea, are pregnant and/ or have a chronic illness such as epilepsy, cardiac disorder, or blood pressure disease, etc. yy 3D Contents are not recommended to those who suffer from stereo blindness or stereo anomaly. Double images or discomfort in viewing may be experienced. yy If you have strabismus (cross-eyed), amblyopia (weak eyesight) or astigmatism, you may have trouble sensing depth and easily feel fatigue due to double images. It is advised to take frequent breaks than the average adult. yy If your eyesight varies between your right and left eye, revise your eyesight prior to watching 3D contents. Symptoms which require discontinuation or refraining from watching 3D contents yy Do not watch 3D contents when you feel fatigue from lack of sleep, overwork or drinking. yy When these symptoms are experienced, stop using/watching 3D contents and get enough rest until the symptom subsides. -- Consult your doctor when the symptoms persist. Symptoms may include headache, eyeball pain, dizziness, nausea, palpitation, blurriness, discomfort, double image, visual inconvenience or fatigue. SAFETY INSTRUCTIONS 11 Viewing Environment � Viewing Distance - Maintain a distance of at least twice the screen diagonal length when watching 3D contents. If you feel discomfort in viewing 3D contents, move further away from the TV. � Viewing Position -- Face the center of the screen at eye level with the head looking straight ahead. Otherwise, you may not be able to view 3D contents properly. Viewing Age yy Infants/Children -- Usage/ Viewing 3D contents for children under the age of 5 are prohibited. -- Children under the age of 10 may overreact and become overly excited because their vision is in development (for example: trying to touch the screen or trying to jump into it. Special monitoring and extra attention is required for children watching 3D contents. -- Children have greater binocular disparity of 3D presentations than adults because the distance between the eyes is shorter than that of adults. Therefore they will perceive more stereoscopic depth compared to adults for the same 3D image. yy Teenagers -- Teenagers under the age of 19 may react with sensitivity due to stimulation from light in 3D contents. Advise them to refrain from watching 3D contens for a long time when they are tired. yy Elderly -- The elderly may perceive less 3D effect compared to the young. Do not sit closer to the TV than the recommended distance. Cautions when using the 3D glasses � Make sure to use LG 3D glasses. Otherwise, you may not be able to view 3D videos properly. � Do not use 3D glasses instead of your normal glasses, sunglasses or protective goggles. � Using modified 3D glasses may cause eye strain or image distortion. � Do not keep your 3D glasses in extremely high or low temperatures. It will cause deformation. � The 3D glasses are fragile and are easily scratched. Always use a soft, clean piece of cloth when wiping the lenses. Do not scratch the lenses of the 3D glasses with sharp objects or clean/wipe them with chemicals. y y When watching 3D videos under fluorescent lights or with three wave length lamps, you may experience the screen blinking. When this occurs, turn the light off or turn it down. y y Other electronic or communication devices should be turned off or put away from the TV because it can cause interference and prevent the 3D function from working properly. y y When you watch TV lying down, 3D images may look darker or invisible. ENGLISH ENG CAUTION 12 INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING ENGLISH ENG NOTE yy Image shown may differ from your TV. yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual. yy The available menus and options may differ from the input source or product model that you are using. yy New features may be added to this TV in the future. yy The TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned off if it will not be watched for some time, as this will reduce energy consumption. yy The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the overall running cost. INSTALLATION PROCEDURE 1 2 3 4 Open the package and make sure all the accessories are included. Attach the stand to the TV set. Connect an external device to the TV set. Make sure the network connection is available.y You can use the TV network functions only when the network connection is made. ASSEMBLING AND PREPARING Unpacking Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item. CAUTION yy Do not use any unapproved items to ensure the safety and product life span. yy Any damage or injuries caused by using unapproved items are not covered by the manufacturer’s warranty. y y Some models have a thin film attached on to the screen and this must not be removed. ASSEMBLING AND PREPARING TV SAVING TV SAVING 1 4 7 LIST 2 5 1 2 3 4 5 6 7 3 6 8 9 0 FLASHBK LIST FAV VOL 3D CH FLASHBK MENU INFO Remote Control, Batteries (AAA) (See p. 29) Q.MENU ENTER BACK 9 0 3D CH P A G E MUTE P A G E MUTE MENU INFO 8 MARK FAV VOL MARK EXIT L/R SELECT FREEZE RATIO P Q.MENU Magic Remote Control, Batteries (AA) (See p. 30) ENTER BACK EXIT L/R SELECT FREEZE RATIO Polishing cloth (Depending on model) Use this to remove dust from the cabinet. Owner’s manual Power Cord x2 Protection Cover (See p. 19) Ferrite core (Depending on model) (See p. 15) Cable Holder (Depending on model) (See p. 23) 3D Glasses (AG-S350) (Depending on model) x2 x8 M4 x 30 M5 x 16 x4 M6 x 28 Power Cord Holder (See p. 23) x8 M4 x 30 M5 x 16 Screw for assembly (Only 50PM69**) (See p. 19) Stand Body (See p. 19) x2 x2 M6 x 28 M8 x 35 Screw for assembly (Only 60PM69**) (See p. 19) Stand Base (See p. 19) ENGLISH ENG ENERGY AV MODE INPUT ENERGY AV MODE INPUT 13 14 ASSEMBLING AND PREPARING ENGLISH ENG Touch Home Eye-bolt & Wall bracket 2 EA (See p. 21) Tip (Depending on model) (See p. 36) Charging Cable (Depending on model) (See p. 36) Touch Pen (Depending on model) (See p. 34) Cradle (Depending on model) (See p. 34) or Isolator (Depending on model) (See p. 16) ASSEMBLING AND PREPARING 15 The items supplied with your product may vary depending on the model. yy Product specifications or contents of this manual may be changed without prior notice due to upgrade yy of product functions. How to use the ferrite core 1 Use the ferrite core to reduce the electromagnetic interference in the PC audio cable. Wind the PC audio cable on the ferrite core thrice. Place the ferrite core close to the TV. (Gray) 10 mm(+ / - 5 mm) [to an External device] [to the TV] [Figure 1] [Cross Section of Ferrite Core] 2 Use the ferrite core to reduce the electromagnetic interference in the power cable. y Wind the power cable on the ferrite core once. Place the ferrite core close to the TV and a wall plug. (Black) [to the TV] [to a wall plug] [Figure 2] [Cross Section of Ferrite Core] 3 Use the ferrite core to reduce the electromagnetic interference in the LAN cable. Wind the LAN cable once on the ferrite core B and thrice on the ferrite core A. Place the ferrite core close to the TV and an External device. A (Gray) B (Gray) [to an External [to the TV] device] A A B [Cross Section of [Figure 3] Ferrite Core] 4 Use the ferrite core supplied to reduce the effects of electromagnetic interference induced into Component Video Y, Pb , Pr , L and R audio cables. Wind the Component Video Y, Pb , Pr , L and R audio cables on the ferrite core once. Place the ferrite core as close as possible to the TV connecting end of cables. (Black) [to an External device] [to the TV] 10 mm(+ / - 5 mm) [Figure 4] [Cross Section of Ferrite Core] - If there are six ferrite cores, attach as per Figure 1,2 and 3. - If there are seven ferrite cores, attach as per Figure 1,2,3 and 4. For an optimal connection, HDMI cables and USB yy devices should have bezels less than 10 mm thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB port. *A *B 10 mm 18 mm ENGLISH ENG NOTE 16 ASSEMBLING AND PREPARING ENGLISH ENG NOTE yy Antenna Isolator Installation Guide -- Use this to install TV in a place where there is a voltage difference between TV Set and GND of antenna signal. »» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact may get hot and excessive heat might cause an accident. -- You can improve the safety when watching TV by efficiently removing power voltage from TV antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall, mount it on the TV. Avoid disconnecting the antenna Isolator after installation. -- Before starting, be sure that the TV antenna is connected. 1. Connect to TV. Wall ANTENNA/ CABLE IN Cable / Antenna or Isolator 2. Connect to Set-Top box. Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box. “Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing - and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11)” When applying the RF Isolator, a slight loss of signal sensitivity can occur. Separate purchase Separate purchase items can be changed or modified for quality improvement without any notification. Contact your dealer to buy these items. These devices only work with certain models. The model name or design may be changed depending on the upgrade of product functions, manufacturer’s circumstances or policies. P Touch Home AG-S3** 3D Glasses AN-VC*** Video Call Camera AN-TP300 Touch Pen, Cradle AN-MR300 Magic Remote Control ASSEMBLING AND PREPARING 17 ENGLISH ENG Parts and buttons Screen Remote control and intelligent sensors1 Power indicator Speakers INPUT SETTINGS OK Buttons AV IN COMPONENT IN VIDEO 2 Y PB /I SETTINGS OK ꔉ H H PR L R 1 VIDEO Button INPUT L/MONO AUDIO R Connection panel AUDIO Description Turns the power on or off. Changes the input source. Accesses the main menus, or saves your input and exits the menus. Selects the highlighted menu option or confirms an input. Adjusts the volume level. Scrolls through the saved programmes. 1 Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment. 18 ASSEMBLING AND PREPARING ENGLISH ENG Lifting and moving the TV Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size. yy When transporting a large TV, there should be at least 2 people. yy When transporting the TV by hand, hold the TV as shown in the following illustration.y CAUTION yy Avoid touching the screen at all times, as this may result in damage to the screen. yy It is recommended to move the TV in the box or packing material that the TV originally came in. yy Before moving or lifting the TV, disconnect the power cord and all cables. yy When holding the TV, the screen should face away from you to avoid damage.y yy Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.y yy When transporting the TV, do not expose the TV to jolts or excessive vibration. yy When transporting the TV, keep the TV upright, never turn the TV on its side or tilt towards the left or right. ASSEMBLING AND PREPARING ENGLISH ENG Setting up the TV Image shown may differ from your TV. Attaching the stand 1 Protection Cover 2 M4 x 30 2EA Only 50PM69** M6 x 28 4EA 3 Only 60PM69** M6 x 28 2EA Stand Body 4 M8 x 35 2EA M5 x 16 8EA Stand Base 19 20 ASSEMBLING AND PREPARING ENGLISH ENG CAUTION yy When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. yy Make sure that the screws are inserted correctly and fastened securely. (If they are not fastened securely enough, the TV may tilt forward after being installed.)y Do not use too much force and over tighten the screws; otherwise screw may be damaged and not tighten correctly. NOTE yy When installing the wall mounting bracket, use the Protection Cover. yy This will protect the opening from accumulating dust and dirt. yy Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse. ASSEMBLING AND PREPARING Securing the TV to a wall 1 Lift and tilt the TV into its upright position on a table. -- Leave a 10 cm (minimum) space from the wall for proper ventilation. 10 cm 10 cm m 10 c 10 cm 2 Connect the power cord to a wall outlet. CAUTION yy Do not place the TV near or on sources of heat, as this may result in fire or other damage. 1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. -- If there are bolts inserted at the eye-bolts position, remove the bolts first. 2 Mount the wall brackets with the bolts to the wall.y Match the location of the wall bracket and the eye-bolts on the rear of the TV. 3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.y Make sure to keep the rope horizontal with the flat surface. CAUTION yy Make sure that children do not climb on or hang on the TV. NOTE yy Use a platform or cabinet that is strong and large enough to support the TV securely. yy Brackets, bolts and ropes are not provided. You can obtain additional accessories from your local dealer. ENGLISH ENG Mounting on a table 21 22 ASSEMBLING AND PREPARING ENGLISH ENG Mounting on a wall A Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed by a qualified professional installer. 10 cm 10 cm 10 cm 10 cm Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table. Separate purchase(Wall Mounting Bracket) Model 50PM69** 60PM69** VESA (A x B) Standard screw Number of screws Wall mount bracket 400 x 400 M6 600 x 400 M8 4 4 PSW400B PSW600B PSW420BX PSW620BX B CAUTION yy Disconnect the power first, and then move or install the TV. Otherwise electric shock may occur. yy If you install the TV on a ceiling or slanted wall, it may fall and result in severe injury.y Use an authorised LG wall mount and contact the local dealer or qualified personnel. yy Do not over tighten the screws as this may cause damage to the TV and void your warranty. yy Use the screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the manufacturer’s warranty. NOTE yy Use the screws that are listed on the VESA standard screw specifications. yy The wall mount kit includes an installation manual and necessary parts. yy The wall mount bracket is not provided. You can obtain additional accessories from your local dealer. yy The length of screws may differ depending on the wall mount. Make sure to use the proper length. yy For more information, refer to the manual supplied with the wall mount. ASSEMBLING AND PREPARING 1 Install the Power Cord Holder and Power Cord. It will help prevent the power cable from being removed by accident. Power Cord Holder 2 Use Cable Holder to neatly secure and position cables together. Position the LAN Cable as shown to reduce the electromagnetic interference wave. y Cable Holder CAUTION Do not move the TV by holding the cable yy holder and power cable holder, as the cable holders may break, and injuries and damage to the TV may occur. ENGLISH ENG Tidying cables 23 24 MAKING CONNECTIONS ENGLISH ENG MAKING CONNECTIONS Antenna Connection Connect the TV to a wall antenna socket with an RF cable (75 Ω). This section on MAKING CONNECTIONS mainly uses diagrams for the PM69** models. Connect various external devices to the TV and switch input modes to select an external device. For more information of external device’s connection, refer to the manual provided with each device. Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices. Wall Antenna Socket NOTE yy The external device connection may differ from the model. yy Connect external devices to the TV regardless of the order of the TV port. yy If you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR. For more information of recording, refer to the manual provided with the connected device. yy Refer to the external equipment’s manual for operating instructions. yy If you connect a gaming device to the TV, use the cable supplied with the gaming device. yy In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear. yy In PC mode, some resolution settings may not work properly depending on the graphics card. NOTE yy Use a signal splitter to use more than 2 TVs. yy If the image quality is poor, install a signal amplifier properly to improve the image quality. yy If the image quality is poor with an antenna connected, try to realign the antenna in the correct direction. yy An antenna cable and converter are not supplied. MAKING CONNECTIONS Transmits the digital video and audio signals from an external device to the TV. Connect the external device and the TV with the HDMI cable as shown. IN 1(ARC) DVD / Blu-Ray / PC HD Cable Box / HD STB USB SB IN 1/ USBApps A / DVI IN 2 U Choose any HDMI input port to connect. It does not matter which port you use. HDMI (*Not Provided) NOTE yy It is recommended to use the TV with the HDMI connection for the best image quality. yy Use the latest High Speed HDMI™ Cable with CEC (Customer Electronics Control) function. yy High Speed HDMI™ Cables are tested to carry an HD signal up to 1080p and higher. yy Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus, HE-AAC yy Supported HDMI Audio format : Dolby Digital, PCM (Up to 192 KHz, 32k/44.1k/48k /88k/96k/176k/192k, DTS Not supported.) ARC (Audio Return Channel) An external audio device that supports yy SIMPLINK and ARC must be connected using HDMI IN 1 (ARC) port. When connected with a high-speed yy HDMI cable, the external audio device that supports ARC outputs optical SPDIF without additional optical audio cable and supports the SIMPLINK function. ENGLISH ENG HDMI Connection 25 26 MAKING CONNECTIONS RGB-PC Connection Transmits the digital video signal from an external device to the TV. Connect the external device and the TV with the DVI-HDMI cable as shown. To transmit an audio signal, connect an audio cable. Transmits the video signal from PC to the TV. To transmit an audio signal, connect an audio cable. USB SB IN 1/ USBApps A / DVI IN 2 U Choose any HDMI input port to connect. It does not matter which port you use. AUDIO IN (RGB/DVI) RGB IN (PC) IN 1(ARC) ( C) ENGLISH ENG DVI to HDMI Connection (*Not Provided) PC (*Not Provided) RGB OUT (PC) AUDIO OUT AUDIO OUT DVI OUT DVD / Blu-Ray / PC / HD Cable Box NOTE yy Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. MAKING CONNECTIONS 27 Composite Connection Transmits analog video and audio signals from an external device to the TV. Connect the external device and the TV with a component cable as shown. Transmits analog video and audio signals from an external device to the TV. Connect the external device and the TV with th e composite cable as shown. 2 L PR R 1 AUDIO VIDEO Y 1 PB PR L R AUDIO VIDEO RED WHITE RED BLUE GREEN (*Not Provided) (*Not Provided) RED L(MONO) R RED VIDEO WHITE AUDIO YELLOW WHITE RED BLUE GREEN VIDEO 2 RED PB L/MONO AUDIO R WHITE Y AV IN VIDEO YELLOW COMPONENT IN L/MONO AUDIO R COMPONENT IN AV IN VIDEO AUDIO DVD / Blu-Ray / HD Cable Box VCR / DVD / Blu-Ray / HD Cable Box NOTE yy If cables are not installed correctly, it could cause this image to display in black and white or with distorted colours. ENGLISH ENG Component Connection 28 MAKING CONNECTIONS USB Connection You may use an optional external audio system instead of the built-in speaker. Connect a USB storage device such as a USB flash memory, external hard drive, or a USB memory card reader to the TV and access the Smart Share menu to use various multimedia files. NOTE Transmits a digital audio signal from the TV to an external device. Connect the external device and the TV with the optical audio cable as shown. HDD HUB USB Hub Digital optical audio connection HDD IN yy If you use an optional external audio device instead of the built-in speaker, set the TV speaker feature to off. / DVI IN 2 USB IN 1/ USB Apps USB IN 2 ENGLISH ENG Audio Connection USB (*Not Provided) (*Not Provided) NOTE (*Not Provided) OPTICAL AUDIO IN Digital Audio System NOTE yy Do not look into the optical output port. Looking at the laser beam may damage your vision. yy Audio with ACP (Audio Copy Protection) function may block digital audio output. yy To use a USB Hub device, make sure that it is connected to the USB Hub port. yy Connect the external power source if your USB is needed. yy Some USB Hubs may not work. If a USB device connected using a USB Hub is not detected, connect it to the USB port on the TV directly. REMOTE CONTROL 29 ENGLISH ENG REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse. CAUTION yy Do not mix old and new batteries, as this may damage the remote control. yy In Analogue TV and some countries, some remote control buttons may not work. Make sure to point the remote control toward the remote control sensor on the TV. (User Guide) Sees user-guide. RATIO Resizes an image. INPUT Changes the input source. TV/RAD Selects Radio, TV and DTV programme. LIST Accesses the saved programme list. Q.VIEW Returns to the previously viewed programme. FAV Accesses your favourite programme. EXIT Clears all on-screen displays and return to TV viewing. RATIO 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW FAV P MUTE SETTINGS HOME MY APPS OK HOME Accesses the Home menus. (Back) Returns to the previous level. GUIDE Shows programme guide. 1 Colour buttons These access special functions in some menus. ( : Red, : Green, : Yellow, : Blue) TV / RAD Used for viewing 3D video. PAGE Moves to the previous or next screen. SETTINGS Accesses the main menus. MY APPS Shows the list of Apps. Navigation buttons (up/down/left/right) Scrolls through menus or options. OK Selects menus or options and confirms your input. INPUT GUIDE 1 2 EXIT SUBTITLE TEXT T.OPT Q.MENU LIVE TV REC ENERGY INFO SAVING or 2 SUBTITLE TEXT ENERGY SAVING T.OPT Q.MENU P A G E 2 TELETEXT BUTTONS These buttons are used for teletext. SUBTITLE Recalls your preferred subtitle in digital mode. Q. MENU Accesses the quick menus. LIVE TV Return to LIVE TV. (Depending on model) Control buttons ( ) Controls the Premium contents, DVR or Smart Share menus or the SIMPLINK compatible devices (USB or SIMPLINK or DVR). REC Uses to adjust DVR menu. (Depending on model) ENERGY SAVING Adjusts the brightness of the screen to reduce energy consumption. INFO Views the information of the current programme and screen. (Depending on model) Accesses the AV devices connected with the HDMI cable through HDMI-CEC. Opens the SIMPLINK menu. 30 MAGIC REMOTE CONTROL FUNCTIONS ENGLISH ENG MAGIC REMOTE CONTROL FUNCTIONS This item is not included for all models. When the message “Magic Remote Control battery is low. Change the battery.” is displayed, replace the battery. To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching and ends to the label inside the compartment, and close the battery cover. Be sure to point the remote control toward the remote control sensor on the TV. To remove the batteries, perform the installation actions in reverse. CAUTION yy Do not mix old and new batteries, as this may damage the remote control. yy Do not need Magic remote Dongle to operate the magic remote control. The Receiver is built into the TV. Pointer (RF transmitter) Blinks the light when operating. (POWER) Turns the TV on or off. BACK Returns to the previous level. BACK HOME HOME Accesses the Home menu. Navigation buttons (up/down/left/right) Scrolls through menus or options. Wheel(OK) Selects menus or options and confirms your input. Scrolls through the saved programmes. If you press the navigation button while moving the pointer on the screen, the pointer disappears, and the Magic Remote Control works as a regular remote control. To display the pointer again, shake the Magic Remote Control from side to side. P MY APPS + Adjusts the volume level. ꕌPꕍ Scrolls through the saved programmes or channels. MUTE Mutes all sounds. MY APPS Shows the list of Apps. Used for viewing 3D video. 11-1 Brief Info Title Test... Info. If you press Wheel(OK) on the Magic Remote Control, the following screen appears. 1 Shows information about the current programme and screen. Pressing this button will display number keypad 2 which you can select programme number. My Apps 3 3 You can select Quick Menu. MAGIC REMOTE CONTROL FUNCTIONS It is necessary to ‘pair’ (register) the magic remote control to your TV before it will work. BACKto register HOME How the Magic Remote Control P MY APPS 1 To register automatically, turn the TV on and press the Wheel(OK) button. When registration is completed, the completion message appears on the screen. 2 If registration fails, turn the TV off and back on, then press the Wheel(OK) button to complete registration. How to re-register the Magic Remote Control BACK HOME 1 Press and hold the BACK and HOME buttons together for 5 seconds to reset, then register it by following “How to register the Magic Remote Control” above. 2 To re-register the Magic Remote Control, press and hold the BACK button for 5 seconds toward the TV. When registration is completed, the completion message appears on the screen. How to use Magic Remote Control 1 If the pointer disappears, move the remote control slightly to left or right. Then, it will automatically appear on the screen. »»If the pointer has not been used for a certain period of time, it will disappear. 2 You can move the pointer by aiming the Pointer Receiver of the remote control at your TV then move it left, right, up or down. »»If the pointer does not work properly, leave the remote control for 10 seconds then use it again. Precautions to Take when Using the Magic Remote Control Use the remote control within the maximum yy communication distance (10 m). Using the remote control beyond this distance, or with an object obstructing it, may cause a communication failure. A communication failure may occur due to yy nearby devices. Electrical devices such as a microwave oven or wireless LAN product may cause interference, as these use the same bandwidth (2.4 GHz) as the Magic Remote Control. The Magic Remote Control may be damaged yy or may malfunction if it is dropped or receives a heavy impact. Take care not to bump into nearby furniture yy or other people when using the Magic Remote Control. Manufacturer and installer cannot provide yy service related to human safety as the applicable wireless device has possibility of electric wave interference. It is recommended that an Access Point (AP) yy be located more than 1 m away from the TV. If the AP is installed closer than 1 m, the Magic Remote Control may not perform as expected due to frequency interference. ENGLISH ENG Registering Magic Remote Control 31 32 USING THE USER GUIDE ENGLISH ENG USING THE USER GUIDE User Guide allows you to more easily access the detailed TV information. 1 Press the HOME button to access the HOME menu. 2 Select User Guide and press Wheel(OK). 1 User Guide OPTION > To set language HOME Settings OPTION Language Selects Menu Language and Audio Language displayed on the screen. Menu Language Selects a language for the display text. PROGRAMME Setting [In Digital Mode Only] Audio Language When watching a digital broadcast containing several audio languages, you can select the language you want. PICTURE, SOUND Setting Subtitle Language OPTION [In Digital Mode Only] Use the Subtitle function when two or more subtitle languages are broadcast. ✎ If subtitle data in a selected language is not broadcast, the default language subtitle will be displayed. LG SMART Function Advanced Function 2 Information My Apps Input List Settings Live TV Search Internet 3D LG Smart W TV Guide User Guide yy You can also access the User Guide by pressing (User Guide) in the remote control. 4 3 To use input device To use Energy Saving feature PROGRAMME Setting To set time options PICTURE, SOUND Setting OPTION Disabled Assistance Advanced Function Information To set TV lock options To set language LG SMART Function 2 Zoom In Close HOME Settings OPTION Language Selects Menu Language and Audio Language displayed on the screen. Menu Language Selects a language for the display text. [In Digital Mode Only] Audio Language When watching a digital broadcast containing several audio languages, you can select the language you want. [In Digital Mode Only] Use the Subtitle function when two or more subtitle Subtitle languages are broadcast. Language ✎ If subtitle data in a selected language is not broadcast, the default language subtitle will be displayed. NOTE 1 3 Recent List User Guide User Guide Try Now To set Magic Remote Control 1 Shows the current watching programme or input source screen. 2 Allows to select the category you want. 3 Allows to select the item you want. You can use ꕌ/ꕍto move between pages. 4 Allows to browse the description of the function you want from the index. Try Now 3 Zoom Out Close 1 Shows the description of the selected menu.y You can use ꕌ/ꕍto move between pages. 2 Moves to the selected menu directly from the User Guide. 3 Zooms in or out the screen. PENTOUCH Using Pentouch Pentouch allows you to use touch pen supported features like Sketchbook, My Gallery, Office Viewer, Internet, Smart Home and PC Link. WARNING Do not drop or throw the touch pen and yy cradle. Do not swing the touch pen and cradle with the charging cable connected to it. This can damage the product or cause personal injury. For people using pacemakers, the distance yy between the touch pen and the pacemaker should be at least 30 cm. Never use it where wireless communication is prohibited. Protect it from extreme vibrations or magnetic objects. Wireless communications can cause malfunctions or failures. Do not use or store the touch pen and cradle yy in direct sunlight, near a hot object (e.g., a heater or fireplace), or in dusty or highhumidity environments. This can result in product deformation, malfunction, failure, or fire. If abnormal sound, smoke, or odor is yy detected, immediately remove the charging cable and stop using the product. Contact a service center. This can cause failures or fire. If fluid leaks from the touch pen and cradle, yy do not touch the fluid with bare hands. If fluid comes into contact with eyes, immediately rinse eyes with abundant tap water, then consult a doctor. The fluid can cause blindness. If the fluid comes into contact with skin or clothing, immediately wash it off with tap water. If the fluid causes skin inflammation or injury, consult a doctor. Do not allow the fluid to come into contact yy with fire. Do not heat the product in a microwave or convection oven. Use the specified USB cable when charging yy the battery. Keep the touch pen and cradle out of reach yy of children and away from unstable locations. Do not let children or pets put the touch pen and cradle in their mouths or lick the touch pen and cradle. Playing with or swallowing it may cause serious injury. Do not use the touch pen and cradle with wet yy hands. Do not let foreign substances (e.g., soft drinks or water) enter the touch pen and cradle; if this happens, do not use the touch pen and cradle. Do not touch the optic receiver of the touch pen and cradle with a sharp object. This can result in electrical shock or damage the product. Do not use the product under extreme yy temperature conditions. Do not use the product immediately after going from the cold outdoors to the warm indoors. This can cause condensation in the pen. This can result in damaging the product. Turn off the power and wait several hours until the moisture evaporates before using the product. Never disassemble or modify the touch yy pen and cradle. The product warranty does not cover damage or injury caused by unauthorized disassembly. This can result in electrical shock or damage the product. If fluid leaks from the touch pen and cradle, yy the use of fire in the vicinity is strictly prohibited. The leaked fluid or gas can is flammable. Avoid extreme shocks or impacts to the yy product, for example, placing a heavy object on it or pressing it. Do not display fixed characters or images yy on the screen for extended periods of time. This can cause image sticking. Do not connect the charging cable to yy peripheral devices or disks that are not specified. This can cause malfunctions or failures. Do not leave the touch pen and cradle on yy the floor. Stepping on it can damage the product or cause personal injury. Be careful when disposing of the product. yy The touch pen and cradle consists of a lithium-polymer battery and plastic material. Burning can be dangerous, so dispose of it according to local regulations. Do not remove the charging cable using yy excessive force. This could damage the charging port and PC. Do not handle the touch pen and cradle with yy excessive force. If you use the touch pen and cradle with excessive force, you may leave foreign substances on the screen. Clean the product with the product cleaning cloth provided. When multiple people use the touch pen yy and cradle, make sure that sufficient space is available. Collisions can cause injury or failures. ENGLISH ENG PENTOUCH 33 34 PENTOUCH ENGLISH ENG Using the Pentouch Function Touch Pen Multiple functions are available on the TV using the pen. Before using the Pentouch functions, please follow the steps below. 1 2 3 h Touc e Hom 1 Pair the pen with the TV. 2 Run the Pentouch program on the TV. 3 Use the TV’s User Guide for details of the Pentouch functions. 4 No. Pairing between Touch Pen What is Pairing? You need to pair the touch pen before using the touch pen. Once paired, you do not need to pair them again unless you: Bought a new pen yy Replaced the old pen with a new one yy Attempt to pair a new touch pen for using two yy pens simultaneously y 1 2 3 4 Description Power button / LED indicator USB charging port Touch Home button Touch pen tip switch Cradle Things to Know Before Pairing This program allows pairing of up to two yy pens. In order to pair 2 pens, please pair yy individually - one pen at a time. Pairing is not possible if a paired pen is yy currently in use. If you pair a new touch pen when two pens yy have already been paired, all the previous pairing data is deleted. Pairing To H uch om e USB charging port NOTE Touch pens and cradles are sold separately yy at dealers. When you leave your touch pen unused for yy a certain period of time (8 minutes), the pen automatically powers off. PENTOUCH 1 Place the pen within 10 cm from the LG logo at the bottom of the TV. 2 Press the (POWER) button on the touch pen once. 3 The LED indicator on the touch pen will red Caution When Unpairing 1 Be careful not to unpair the pen by mistake. If unpaired, try pairing it again. 2 If you unpair and pair a normally functioning touch pen, the other paired pen may not work. In this case, unpair the nonfunctioning touch for 2 seconds and blinks green 3 times when pen and pair it again by following the steps pairing is complete. described in the Pairing for the First Time 4 If the LED indicator is red for 4 - 5 seconds and section. blinks red 3 times, pairing is not successful. Please try pairing again. 5 Once a pen is paired, the red LED blinks once when you press the Touch Home button. Unpairing (Resetting the touch pen) 1 Press the Touch Home button on the touch pen and check that the red LED blinks once. 2 Press the Touch Home button and the (POWER) button together, regardless of sequence, for more than 4 seconds. 3 If you release the buttons after 4 seconds, the pen will be reset. The red LED will blink three times and the pen will be turned off. Touch pen Operation Once paired, you can use the touch pen in the y following ways. 1 Powering ony - Press the (POWER) button once. The red and green LEDs will remain lit to indicate that the power is on. 2 Powering offy - Press the (POWER) button for more than 3 seconds and release it. The red LED will blink 3 times and the pen will be turned off. 3 Return to the Touch Home by pressing Touch Home button while using the touch pen. NOTE When a menu is displayed on the screen, the yy Touch Home button does not work. Close the menu and then Press the Touch Home button. ENGLISH ENG Pairing for the First Time 35 36 PENTOUCH ENGLISH ENG Tip replacement 1 Detach the tip holder and the tip to be replaced from the pen.y y y y y y y y Tip Holder y Tip 2 Insert a new tip into the detached tip holder and assemble the tip holder with the pen.y Tip Tip Holder Charging the touch pen Charging on the cradle yy or Charging directly yy h Toucme Ho or To Ho uc m h e NOTE After an hour and 30 minutes of a continuous yy charge, you can use the touch pen for about 2 hours. Do not use the touch pen while it is charging. yy Green LED will be turned on during using yy touch pen. If you don’t use touch pen, it will be automatically turned off after 8 minutes. Touch pen LED indicator for battery status yy - Charging: Red LED - Charging complete: Green LED - No battery power: Red LED blinks every second and powers off automatically. - LED ON Sleep mode: If no switch (tip switch, function key, power key) is pressed for 10 seconds, the device enters sleep mode but the LED stays green. - LED OFF Sleep mode: If there is no input for one minute after entering LED ON Sleep mode, the LED is turned off and the device enters LED OFF Sleep mode. - Power off mode: The device is powered off if there is no input for 8 minutes. If the cradle is connected to the TV, the pen yy can be charged when the TV is switched on or is on standby. If the pen is connected directly to the TV yy through the charging cable, the pen cannot be charged when the TV is on standby. MAINTENANCE 37 Cleaning your TV Clean your TV regularly to keep the best performance and to extend the product lifespan. CAUTION yy Make sure to turn the power off and disconnect the power cord and all other cables first. yy When the TV is left unattended and unused for a long time, disconnect the power cord from the wall outlet to prevent possible damage from lightning or power surges. Screen, frame, cabinet and stand yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth. yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent. Then wipe immediately with a dry cloth. CAUTION yy Avoid touching the screen at all times, as this may result in damage to the screen. yy Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in scratches and image distortions. yy Do not use any chemicals as this may damage the product. yy Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction. Power cord Remove the accumulated dust or dirt on the power cord regularly. ENGLISH ENG MAINTENANCE 38 TROUBLESHOOTING / EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG TROUBLESHOOTING General Problem Solution Cannot control the TV with the remote control. yy Check the remote control sensor on the product and try again. yy Check if there is any obstacle between the product and the remote control. to , to yy Check if the batteries are still working and properly installed ( No image display and no sound is produced. yy Check if the product is turned on. yy Check if the power cord is connected to a wall outlet. yy Check if there is a problem in the wall outlet by connecting other products. The TV turns off suddenly. yy Check the power control settings. The power supply may be interrupted. yy Check if the Auto sleep feature is activated in the Time settings. yy If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity. When connecting to the PC (RGB/HDMI DVI), ‘No signal’ or ‘Invalid Format’ is displayed. yy Turn the TV off/on using the remote control. yy Reconnect the RGB/HDMI cable. yy Restart the PC with the TV on. ). Pentouch Problem Solution The touch pen does not work. yy Check that the touch pen is paired for use. (The touch pen is correctly paired if the red LED is on once when you press the Touch Home button on the touch pen.) yy Make sure the touch pen is paired. (The red LED turning on once when pressing the power button on the touch pen means that it is paired and ready to be used.) The touch pen works on and off. yy Check if the touch pen is fully charged. (When it needs to be charged, the red LED blinks every two seconds.) yy Unpair the touch pen and pair it again before using it. EXTERNAL CONTROL DEVICE SETUP To obtain the external control device setup information, please visit www.lg.com ENVIRONMENTAL INFORMATION 39 ENGLISH ENG ENVIRONMENTAL INFORMATION (India only) WEEE Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the e-waste (Management and Handling) Rules, 2011. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. 5. This product does not contain any of the hazardous substances as specified in the rule 13 (1) and (2) of the e-waste (Management and Handling) Rules, 2011. i;kZoj.kh; tkudkjh WEEE vius iqjkus midj.k dk fuiVku ƒ. tc ;g dkVs x;s ifg;s okys fcu dk fpg+u fdlh mRikn ds lkFk layXu gksrk gS rks bldk vFkZ gS mRikn ¼izca/ku vkSj gFkkyu½ fu;e „Œƒƒ ds varxZr lfEefyr fd;k x;k gSA „. lHkh bysfDVªdy ,oa vkSj bysDVªkfud mRiknkas dks ljdkj ;k LFkkuh; vf/kdkfj;ksa }kjk fu;qDr uxjikfydk ls vyx izkf/kd`r dh xbZ laxzg lqfo/kkvksa ds ek/;e ls fuiVk;k tkuk pkfg,A /kkjk …. lgh rjhds ls vius iqjkus midj.kksa dk fuiVku okrkoj.k vkSj ekuoh; LokLF; dss fy, laHkkfor udkjkRed ifj.kkeksa dks jksdus esa enn djsxkA †. vius iqjkus midj.kksa ds fuiVku ds lac/k esa vkSj vf/kd folr`r tkudkjh ds fy,] d`i;k vius uxj dk;kZy;] ls vkius mRikn [kjhnk Fkk] ogka laidZ djsaA ‡. bl mRikn esa fuiVku lsok ;k tgka ¼izca/ku vkSj gFkkyu½ fu;e] „Œƒƒ ds fu;e ƒ… ¼ƒ½ vkSj ¼„½ esa funsZ’kkuqlkj dksbZ Hkh gkfudkjd inkFkZ “kkfey ugha gSA 40 SPECIFICATIONS ENGLISH ENG SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions. Wireless LAN module(WN8122E) specification Standard IEEE802.11a/b/g/n Frequency Range 2400 to 2483.5 MHz 5150 to 5250 MHz 5725 to 5850 MHz Modulation CCK / OFDM / MIMO Output Power (Typical) Data rate Antenna Gain (Typical) Occupied bandwidth 802.11a: 14 dBm 802.11b: 17 dBm 802.11g: 15 dBm 802.11n - 2.4GHz: 13.5 dBm 802.11n - 5GHz: 12 dBm 802.11a/g: 54 Mbps 802.11b: 11 Mbps 802.11n: 300 Mbps 2400 to 2483.5 MHz: -0.79dBi 5150 to 5250 MHz: 0.62dBi 5725 to 5850 MHz: 0.52dBi 802.11a/b/g: HT20 802.11n: HT20/40 Because band channel used by the country could be different, the user can not change or adjust the yy operating frequency and this product is set for the regional frequency table. Bluetooth module (BM-LDS302) specification Standard Frequency Range Output Power (Max.) Data rate (Max.) Communication Distance Bluetooth Version 3.0 2400 ~ 2483.5 MHz 10 dBm or lower 3 Mbps Line of Open Sight approx. 10 m Pentouch Dongle (AN-TD200) specification Frequency Rang Modulation Output Power (Max.) Receive sensitivity Data rate (Max.) 2400 ~ 2483.5 MHz GFSK 0 dBm - 82 dBm 2 Mbps SPECIFICATIONS 41 50PM69** 60PM69** 50PM6900-TE 60PM6900-TE With stand (mm) 1168.0 x 754.0 x 336.0 1386.8 x 888.8 x 372.0 Without stand (mm) 1168.0 x 704.0 x 53.0 1386.8 x 818.2 x 53.0 With stand (kg) 28.3 39.4 Without stand (kg) 26.4 36.4 MODELS Dimensions (W x H x D) Weight Power requirement AC 100-240 V~ 50 / 60 Hz Environment condition Operating temperature 0 °C to 40 °C Operating humidity Less than 80 % Storage temperature -20 °C to 60 °C Storage humidity Less than 85 % Digital TV New Zealand, Singapore Australia Television System Programme Coverage Television System Programme Coverage Indonesia, Israel, Myanmar, Sri Lanka Vietnam, Malaysia Television System Programme Coverage Television System Programme Coverage Iran, Algeria, Tunisia, Digital model Television System Analogue model, India, Thailand, South Africa, -- Television System Programme Coverage Programme Coverage External Antenna Impedance DVB-T UHF 21 to 69 DVB-T VHF 06 to 12, UHF 27 to 69 DVB-T UHF 21 to 69 DVB-T VHF 6 to 12, UHF 21 to 69 DVB-T VHF 5 to 12, UHF 21 to 69 Analogue TV PAL/SECAM-B/G/D/K, PAL-I BG : VHF/UHF 1 to 69, CATV 01 to 47 I : VHF/UHF 1 to 69, CATV 01 to 47 DK : VHF/UHF 1 to 69, CATV 01 to 47 PAL B/B B/B : VHF/UHF 0 to 75, CATV : 2 to 44 PAL/SECAM-B/G/D/K, PAL-I, NTSC-M BG : VHF/UHF 1 to 69, CATV 01 to 47 I : VHF/UHF 1 to 69, CATV 01 to 47 DK : VHF/UHF 1 to 69, CATV 01 to 47 M : VHF/UHF 2 to 78, CATV 01 to 71 PAL/SECAM-B/G/D/K, PAL-I, NTSC-M BG : VHF/UHF 1 to 69, CATV 01 to 47 I : VHF/UHF 1 to 69, CATV 01 to 47 DK : VHF/UHF 1 to 69, CATV 01 to 47 M : VHF/UHF 2 to 78, CATV 01 to 71 PAL/SECAM-B/G/D/K, PAL-I, NTSC-M BG : VHF/UHF 1 to 69, CATV 01 to 47 I : VHF/UHF 1 to 69, CATV 01 to 47 DK : VHF/UHF 1 to 69, CATV 01 to 47 M : VHF/UHF 2 to 78, CATV 01 to 71 - PAL/SECAM-B/G/D/K, PAL-I, NTSC-M - BG : VHF/UHF 1 to 69, CATV 01 to 47 I : VHF/UHF 1 to 69, CATV 01 to 47 DK : VHF/UHF 1 to 69, CATV 01 to 47 M : VHF/UHF 2 to 78, CATV 01 to 71 75 Ω 75 Ω ENGLISH ENG Product specifications may be changed without prior notice due to upgrade of product functions. For the power supply and power consumption, refer to the label attached to the product. 42 SPECIFICATIONS ENGLISH ENG HDMI/DVI-DTV supported mode Component port connecting information Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 720x480 31.469 31.5 59.94 60 720x576 31.25 50 1280x720 37.5 44.96 45 50 59.94 60 1920x1080 33.72 33.75 28.125 26.97 27 33.716 33.75 56.25 67.43 67.5 59.94 60 50 23.97 24 29.976 30.00 50 59.94 60 Component ports on the TV Y PB PR Video output ports on DVD player Y Y Y Y PB B-Y Cb Pb PR R-Y Cr Pr Signal Component 480i/576i O 480p/576p O 720p/1080i O 1080p O (50 Hz / 60 Hz only) SPECIFICATIONS 43 yyMedia contents and a player need to support HDMI 3D Frame Packing, HDMI 3D Side by Side, HDMI 3D Top & Bottom to play in 3D. yyVideo, which is input as HDMI,USB,DLNA, is switched into the 3D screen automatically. (This function does not support all of the 3D video format. The specific 3D video format is not switched into the 3D screen automatically. ) yy2D->3D mode is available to watch for all signals. yyFor models supporting WiDi, you can set the 3D mode in the same way as in RGB (PC) mode. Input Signal Resolution 480p 640X480 720X480 640X480 720X480 576p 720X576 Component USB DLNA DTV 31.469 / 31.5 62.5 31.25 59.94/ 60 50 59.94 / 60 50 23.97 / 24 29.97 / 30 23.976 / 24 29.97 / 30.00 50 1024X768 1360X768 67.43 / 67.5 48.363 60.015 59.94 / 60 60.004 60.015 1920X1080 67.50 60.00 1024X768 1360X768 1920X1080 48.363 60.015 67.50 37.5 45 28.125 33.75 60.004 60.015 60.00 50 60 50 60 720p 1280X720 1080i 1920X1080 1080p RGB-PC 62.938 / 63 Vertical Frequency (Hz) 75 89.91/90 37.5 44.96 / 45 67.432 / 67.5 56.25 62.5 33.72 / 33.75 28.125 53.946 / 54 67.432/67.5 26.973 / 27 33.716 / 33.75 56.250 HDMI-DTV HDMI-PC Horizontal Frequency (kHz) 1920X1080 720p 1280X720 1080i 1920X1080 1080p 1080p 1920X1080 1920X1080 33.75 33.75 50 59.94 / 60 50 59.94 / 60 59.94 / 60 50 Playable 3D video format Frame packing, Line alternative Side-by-side(Full), Top-and-Bottom, Side-by-side(Half) Frame packing, Line alternative Side-by-side(Full), Top-and-Bottom, Side-by-side(Half) Frame packing, Line alternative Side-by-side(Full), Top-and-Bottom Side-by-side(Half), Single Frame Sequential Frame packing, Field alternative Field alternative Frame packing Side-by-side(Full), Top-and-Bottom, Side-by-side(Half) Frame packing, Line alternative Side-by-side(Full), Top-and-Bottom, Side-by-side(Half), Checkerboard Top-and-Bottom, Side-by-side(Half), Checkerboard, Single Frame Sequential, Row Interleaving, Column Interleaving Side by Side(Half), Top & Bottom Side by Side(Half), Top & Bottom Side by Side(Half), Top & Bottom Checkerboard, Single Frame Sequential Row Interleaving, Column Interleaving Side by Side(Half), Top & Bottom Side by Side(Half), Top & Bottom Side by Side(Half), Top & Bottom Side by Side, Top & Bottom 30 Side by Side, Top & Bottom, Checker Board, Single Frame Sequential, Row Interleaving, Column Interleaving, MPO(Photo), JPS(Photo) (Photo : Side by Side(Half), Top & Bottom) 30 Side by Side, Top & Bottom, Checker Board, Single Frame Sequential, Row Interleaving, Column Interleaving, MPO(Photo), JPS(Photo) (Photo : Side by Side(Half), Top & Bottom) Signal Playable 3D video format 720p, 1080i Side by Side, Top & Bottom ENGLISH ENG 3D supported mode Record the model number and serial number of the TV. Refer to the label on the back cover and quote this information to your dealer when requiring any service. MODEL SERIAL (Only DTV) OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating your set and retain it for future reference. PM47** PM67** PM69** PM97** www.lg.com 2 IR CODES ENGLISH ENG IR CODES (Depending on model) Code (Hexa) Function Note Code (Hexa) Function Note 08 (POWER) Remote control Button (Power On/Off) B0 Remote control Button BA yy Remote control Button 7A (User Guide) Remote control Button 8F Remote control Button 79 RATIO Remote control Button 8E Remote control Button 0B INPUT Remote control Button BD REC Remote control Button INFO Remote control Button F0 TV/RAD Remote control Button AA 10-19 Alphanumeric buttons 0-9 Remote control Button 95 53 LIST Remote control Button 7E 1A Q.VIEW Remote control Button 02 + Remote control Button 1E FAV Remote control Button 00 ꕌP Remote control Button DC Remote control Button 03 09 - Remote control Button MUTE Remote control Button 01 Pꕍ Remote control Button 43 SETTINGS Remote control Button 7C HOME Remote control Button 42 MY APPS Remote control Button 40 ^ Remote control Button 07 < Remote control Button 44 OK Remote control Button 06 > Remote control Button 41 v Remote control Button 28 (BACK) Remote control Button AB GUIDE Remote control Button 5B REC EXIT Remote control Button 72 RED Remote control Button 71 GREEN Remote control Button 63 YELLOW Remote control Button 61 BLUE Remote control Button 20 TEXT Remote control Button 21 T.OPT Remote control Button 45 SUBTITLE/ Q.MENU Remote control Button B1 n LIVE TV Remote control Button ENERGYSAVING Remote control Button Remote control Button EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG EXTERNAL CONTROL DEVICE SETUP (Depending on model) Image shown may differ from your TV. yy RS-232C Setup Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Type of connector; D-Sub 9-Pin Male 1 6 NOTE yy RS-232C on this TV is intended to be used with third party RS-232C control hardware and software. The instructions below are provided to help with programming software or to test functionality using telenet software. yy RS-232C connection cables are not supplied with the product. AV IN COMPONENT IN VIDEO No. 1 2 3 4 5 6 7 8 9 L/MONO AUDIO R 2 Y PB PR L R 1 VIDEO AUDIO LAN 3 5 9 Pin name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection 4 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG RS-232C Configurations Set ID Set ID number. "Real Data Mapping" (See p.9) 7-Wire Configurations (Standard RS-232C cable) RXD TXD GND DTR DSR RTS CTS PC TV 2 3 5 4 6 7 8 3 2 5 6 4 8 7 D-Sub 9 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS PC TV 2 3 5 4 6 7 8 3 2 5 6 4 7 8 D-Sub 9 D-Sub 9 2 Press the Navigation buttons to scroll to SETUP and press OK. 3 Press the Navigation buttons to scroll to OPTION and press OK. 4 Press the Navigation buttons to scroll to Set ID and press OK. 5 Scroll left or right to select a set ID number and select Close. The adjustment range is 1 to 99. 6 When you are finished, press EXIT. 3-Wire Configurations(Not standard) 1 Press Home to access the Home menus. TXD RXD GND DTR DSR RTS CTS EXTERNAL CONTROL DEVICE SETUP 5 yy Baud rate: 9600 bps (UART) yy Data length: 8 bits yy Parity : None ENGLISH ENG Communication Parameters yy Stop bit: 1 bit yy Communication code: ASCII code yy Use a crossed (reverse) cable. Command reference list COMMAND1 COMMAND2 DATA (Hexadecimal) COMMAND1 COMMAND2 DATA (Hexadecimal) 01. Power k a 00 to 01 14. Colour Temperature x u 00 to 64 02. Aspect Ratio k c (See p.6) 15. ISM Method j q 00 to 05 03. Screen Mute k d (See p.6) 16. Energy Saving j q 00 to 05 04. Volume Mute k e 00 to 01 17. Auto Configuration j u 01 05. Volume Control k f 00 to 64 18. Tune Command m a (See p.8) 06. Contrast k g 00 to 64 19. Programme m Add/Skip b 00 to 01 07. Brightness k h 00 to 64 20. Key c Key Code b (See p.9) m 08. Colour k i 00 to 64 21. Input select x (Main) 09. Tint k j 00 to 64 22. 3D x (Only 3D models) t (See p.9) 10. Sharpness k k 00 to 32 23. Extended 3D x (Only 3D models) v (See p.10) 11. OSD Select k l 00 to 01 12. Remote k Control Lock Mode m 00 to 01 13. Balance t 00 to 64 k yy Note : During USB operations such as DivX or EMF, all commands except Power(ka) and Key(mc) are not executed and treated as NG. 6 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] First command to control the TV.(j, k, m or x) [Command 2] Second command to control the TV. [Set ID] You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled. Set ID is indicated as decimal (1 to 99) on menu and as Hexa decimal (0x0 to 0x63) on transmission/receiving protocol. [DATA] To transmit command data. Transmit ‘FF’ data to read status of command. [Cr] Carriage Return ASCII code ‘0x0D’ [ ] ASCII code ‘space (0x20)’ OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] * The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC 01. Power (Command: k a) ►► To control Power On/Off of the set. Transmission[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off 01 : Power On Ack [a][ ][Set ID][ ][OK/NG][Data][x] ►► To show Power On/Off. Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK/NG][Data][x] * Similarly, if other functions transmit ‘0xFF’ data based on this format, Acknowledgement data feed back presents status about each function. * OK Ack., Error Ack. and other message may display on the screen when TV is power On. 02. Aspect Ratio (Command: k c) (Main Picture Size) ►► To adjust the screen format. (Main picture format) You can also adjust the screen format using the Aspect Ratio in the Q.MENU. or PICTURE menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 01 : 02 : 04 : 06 : 07 : 09 : 0B : 10 to Normal screen (4:3) Wide screen (16:9) Zoom Original 14:9 Just Scan Full Wide 1F : Cinema Zoom 1 to 16 Ack [c][ ][Set ID][ ][OK/NG][Data][x] * Using the PC input, you select either 16:9 or 4:3 screen aspect ratio. * In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz / 60 Hz, 1080p 24 Hz / 30 Hz / 50 Hz / 60 Hz), Component( 720p, 1080i, 1080p 50 Hz / 60 Hz) mode, Just Scan is available. * Full Wide is supported only for DTV. computer. 03. Screen Mute (Command: k d) Error Acknowledgement [Command2][ ][Set ID][ ][NG][Data][x] * The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors. Data00: Illegal Code ►► To select screen mute on/off. Transmission [k][d][ ][Set ID][ ][Data][Cr] Data 00 : Screen mute off (Picture on) Video mute off 01 : Screen mute on (Picture off) 10 : Video mute on Ack [d][ ][Set ID][ ][OK/NG][Data][x] * In case of video mute on only, TV will display On Screen Display(OSD). But, in case of Screen mute on, TV will not display OSD. EXTERNAL CONTROL DEVICE SETUP ►► To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission [k][e][ ][Set ID][ ][Data][Cr] Data 00 : Volume mute on (Volume off) 01 : Volume mute off (Volume on) Ack [e][ ][Set ID][ ][OK/NG][Data][x] 05. Volume Control (Command: k f) ►► To adjust volume. You can also adjust volume with the VOLUME buttons on remote control. Transmission [k][f][ ][Set ID][ ][Data][Cr] 09. Tint (Command: k j) ►► To adjust the screen tint. You can also adjust tint in the PICTURE menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Red : 00 to Green : 64 * Refer to ‘Real data mapping’. (See p.9) Ack [j][ ][Set ID][ ][OK/NG][Data][x] 10. Sharpness (Command: k k) ►► To adjust the screen sharpness. You can also adjust sharpness in the PICTURE menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. (See p.9) Data Min : 00 to Max : 32 * Refer to ‘Real data mapping’. (See p.9) Ack [f][ ][Set ID][ ][OK/NG][Data][x] Ack [k][ ][Set ID][ ][OK/NG][Data][x] 06. Contrast (Command: k g) ►► To adjust screen contrast. You can also adjust contrast in the PICTURE menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. (See p.9) Ack [g][ ][Set ID][ ][OK/NG][Data][x] 11. OSD Select (Command: k l) ►► To select OSD (On Screen Display) on/off when controlling remotely. Transmission [k][l][ ][Set ID][ ][Data][Cr] Data00 : OSD off 01 : OSD on Ack [l][ ][Set ID][ ][OK/NG][Data][x] 07. Brightness (Command: k h) ►► To adjust screen brightness. You can also adjust brightness in the PICTURE menu. Transmission [k][h][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. (See p.9) Ack [h][ ][Set ID][ ][OK/NG][Data][x] 12. Remote control lock mode (Command: k m) ►► To lock the front panel controls on the monitor and remote control. Transmission [k][m][ ][Set ID][ ][Data][Cr] 08. Colour (Command: k i) ►► To adjust the screen colour. You can also adjust colour in the PICTURE menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. (See p.9) Ack [i][ ][Set ID][ ][OK/NG][Data][x] Data 00 : Lock off 01 : Lock on Ack [m][ ][Set ID][ ][OK/NG][Data][x] * If you are not using the remote control, use this mode. When main power is on/off, external control lock is released. * In the standby mode, if key lock is on, TV will not turn on by power on key of IR & Local Key. ENGLISH ENG 04. Volume Mute (Command: k e) 7 8 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG 13. Balance (Command: k t) 17. Auto Configure(Command: j u) ►► To adjust balance. You can also adjust balance in the AUDIO menu. ►► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode. Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. (See p.9) Ack [t][ ][Set ID][ ][OK/NG][Data][x] Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 01: To set Ack [u][ ][Set ID][ ][OK/NG][Data][x] 14. Colour Temperature (Command: x u) 18. Tune Command (Command: m a) ►► To adjust colour temperature. You can also adjust Colour Temperature in the PICTURE menu. ►► Select channel to following physical number. Transmission [x][u][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. (See p.9) Ack [u][ ][Set ID][ ][OK/NG][Data][x] 15. ISM Method (Command: j p) ►► To control the ISM method. You can also adjust ISM Method in OPTION menu. Transmission [j][p][ ][Set ID][ ][Data][Cr] Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01][ ][Data02][Cr] Data00 : High channel data Data01 : Low channel data ex. No. 47 -> 00 2F (2FH) No. 394 -> 01 8A (18AH), DTV No. 0 -> Don’t care Data02 : 0x00 : Analogue Main 0x10 : DTV Main 0x20 : Radio Channel data range Analogue - Min: 00 to Max: C7 (0 to 199) Digital - Min: 00 to Max: 3E7 (0 to 999) Ack [a][ ][Set ID][ ][OK/NG][Data][x] Data Min: 00 to Max: 7DH Data 02: Orbiter 08: Normal 20: Colour Wash Ack [p][ ][Set ID][ ][OK/NG][Data][x] 19. Programme Add/Skip(Command: m b) ►► To set skip status for the current Programme. Transmission [m][b][ ][Set ID][ ][Data][Cr] Data00 : Skip 16. Energy Saving (Command: j q) 01 : Add Ack [b][ ][Set ID][ ][OK/NG][Data][x] ►► To reduce the power consumption of the TV. You can also adjust Energy Saving in PICTURE menu. Transmission [j][q][ ][Set ID][ ][Data][Cr] Data 00: 01: 02: 03: 04: 05: Off Minimum Medium Maximum Intelligent Sensor Screen off Ack [q][ ][Set ID][ ][OK/NG][Data][x] 20. Key(Command: m c) ►► To send IR remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Key code (See p.2) Ack [c][ ][Set ID][ ][OK/NG][Data][x] EXTERNAL CONTROL DEVICE SETUP 9 ►► To change 3D mode for TV. ►► To select input source for main picture. (Use the feature depending on your model.) Transmission [x][t][ ][Set ID][ ][Data01][ ][Data02][ ] [Data03][ ][Data04][Cr] Transmission [x][b][ ][Set ID][ ][Data][Cr] Data Structure MSB 0 LSB 0 0 0 External Input Input 0 0 1 0 1 1 0 0 1 0 0 0 Input Number 0 0 0 0 0 0 1 1 1 External 0 0 0 1 1 1 0 0 0 0 0 0 0 Input Number 0 0 0 0 0 1 0 1 0 0 1 1 0 1 0 0 0 1 0 1 0 Data DTV Analogue AV Component RGB 00 : Step 0 A: Step 10 (Set ID 10) 0 Data02 00 : Top and Bottom 01 : Side by Side 02 : Check Board 03 : Single Frame Sequential 04 : Column interleaving 05 : Row interleaving Data03 00 : Right to Left 01 : Left to Right HDMI Data04 3D Effect(3D Depth) : 0~20 Data Input1 Input2 Input3 Input4 Ack [b][ ][Set ID][ ][OK/NG][Data][x] * Real data mapping Data01 00 : 3D On 01 : 3D Off 02 : 3D to 2D 03 : 2D to 3D *If data01 is 01(3D off), data02, data03 and data04 have no meaning. *If data01 is 02(3D to 2D), data02, data03 and data04 have no meaning. *If data01 is 03(2D to 3D), data02 and data03 have no meaning. Data 01 00 01 02 03 Data 02 O X X X Data 03 O X X X Data 04 X X X O X : Don't care Ack : All data must be consist of 2 characters. F: Step 15 (Set ID 15) [t][ ][OK] [Data01][ ][Data02][ ][Data03][ ][Data04] [x] 10 : Step 16 (Set ID 16) [t][ ][NG] [Data01] [x] 64 : Step 100 6E : Step 110 73 : Step 115 74 : Step 116 CF : Step 199 FE : Step 254 FF : Step 255 ENGLISH ENG 22. 3D (Command: x t) (Only 3D models) 21. Input select (Command: x b) (Main Picture Input) 10 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG 23. Extended 3D(Command: x v) (Only 3D models) ►► To change 3D mode for TV. Transmission [x][v][ ][Set ID][ ][Data01][ ][Data02] [Cr] Data01 : 3D option item that user wants to adjust Data 00 01 02 07 08 09 3D Option 3D Picture Correction 3D Depth 3D Viewpoint 3D Sound Zooming Normal Image View 3D Mode Data02 : It has own range for each 3D option determined by Data01. 1) When Data 01 is 00 Data 00 01 3D Picture Correction Right to Left Left to Right 2) When Data 01 is 01 Data Min: 00 ~ Max: 14 3) When Data 01 is 02 Data Min: 00 ~ Max: 14 4) When Data01 is 07 Data 00 01 3D Sound Zooming Off On 5) When Data01 is 08 Data 00 01 Normal Image View Off On 6) When Data01 is 09 Data 00 01 02 03 04 3D Mode Standard Sports Cinema Extreme Manual (* transmit by Hexadecimal code) Ack : All data must be consist of 2 characters. [v][ ][OK] [Data01][ ][Data02] [x][v][ ][NG] [Data01] [x] * Use the feature depending on your model.