LG | CF-34C60TM | LG CF-29H20NM Owner’s Manual

Contents
Installation
3
Location and function of controls
Remote control handset
Battery installation
4
Front
Basic
panel
7
operation
On and off
Programme selection
adjustment / Mute function
On screen language selection (option)
Volume
On
8
screen menus
Menu selection
up TV stations
Auto programme tuning
Manual programme tuning
Setting
9
Fine
tuning
Programme
Picture
edit
13
adjustment
Sound
14
adjustment
adjustment
Stereo/Dual reception
NICAM reception (option)
Sound
Sound
output selection
Other functions
TV and AV modes / Child lock
Auto sleep / Blue back (option)
Off timer / On timer
Tilt
16
(option)
Auto demonstration
Calling
a
programme table
PIP
operation (option)
Programme selection for sub picture
mode
selection
for sub picture
Input
Swapping between main and sub pictures
Sub picture size / Sub picture freeze
Sub picture position change / Programme scan
19
On and off /
Teletext (option)
Switch on/off
20
LIST mode / TOP mode / FASTEXT mode
Special
teletext functions
Connection of external equipment
Aerial socket
Euro scart socket
Audio/Video in/out sockets
S-video/Audio in sockets
Woofer socket
Troubleshooting
2
23
(S-AV)
(option)
check list
25
Installation
Contents
Power
This set
operates
indicated
on
on
the label
an
on
AC mains
the back
the set. In the event of thunderstorms
out the aerial and mains
the voltage is as
apply DC power to
powercuts, please pull
supply,
Never
cover.
or
plugs.
Warning
To
prevent fire
or
shock
hazard, do
not expose the set to rain or
moisture.
Service
Never
remove
the back
high voltage
properly, unplug it
very
cover of the set as this can expose you to
and other hazards. If the set does not operate
and call your dealer.
Aerial
Connect the aerial cable to the socket marked
cover.
For the best
reception
an
+75§U on
the back
outdoor aerial should be used.
Location
Position your set
so
that
no
bright light
or
sunlight
falls
directly
onto the screen. Care should be taken not to expose the set to
any unnecessary vibration, moisture, dust or heat. Also ensure that
the set is placed in a position to allow a free flow of air. Do not
cover
the ventilation
openings
on
the back
cover.
3
Location and function of controls
Contents
All the functions
can
be controlled with the remote control handset.
Some functions
can
also be
panel
adjusted
with the buttons
on
the front
of the set.
Remote control handset
Before you use the remote control
batteries. See the next page.
handset, please install the
1
POWER
1.
MUTE
POWER
switches the set
2
1
2
3
EYE
4
5
6
SRS
8
3
2.
8
9
TV/AV
PIP
0
TEXT
MENU
10
3.
from
standby
or
off to
standby.
MUTE
switches the sound
9
7
on
on or
off.
NUMBER BUTTONS
switch the set
from
on
standby
or
directly
select
a
number.
11
15
4.
PIP BUTTONS
(option)
PIP
switches the sub
selects
VOL
OK
VOL
12
programme for the sub
selects the
PSM
SSM
DUAL
SIZE
STILL POSITION9/4 PIP
PIP
XT
13
SIZE
14
adjusts
LIST
5
V
C
R
CH+
REW
PLAY
the sub
P/STILLSTOP
picture.
picture
picture.
size.
picture.
POSITION
relocates the sub
picture
in clockwise direction.
9/4 PIP
FF
switches
CH
mode for the sub
input
freezes motion of the sub
15
START LENGTHSP/LPON/OFF
QSR
picture.
STILL
M
7
a
INPUT
PR+SWAPINPUT
T
off.
alternates between main and sub
4
6
on or
SWAP
PR
PR-
picture
PR+/-
PR
on
REC
sub
or
off the programme
scan
pictures.
5.PSM
(Picture Status Memory)
preferred picture setting.
recalls your
6.
(With TELETEXT)
SSM
(Sound Status Memory)
preferred sound setting.
recalls your
7.VCR BUTTONS
control
4
a
(option)
LG video cassette recorder.
mode
through
9
or
4
Location and function of controls
8. EYE
(option)
Eye
switches the
function
off.
on or
No Function
9. SRS
(Sound Retrieval System)
switches the SRS function
on or
off.
10. TV/AV
selects TV
clears the
or
AV mode.
menu
from the
screen.
1
POWER
MUTE
11. MENU
calls
12.
or
clears the main
2
menu.
a
programme
or a menu
2
3
EYE
4
5
6
SRS
7
8
9
TV/AV
PIP
0
LIST
MENU
8
¡a/¡a (Programme Up/Down)
on from standby.
switches the set
selects
1
3
item.
9
10
¢¸/¢º (Volume Down/Up)
adjusts the volume.
adjusts menu settings.
11
14
OK
your selection
accepts
or
displays
the current mode.
13.DUAL
PR
selects the
selects
language during dual language broadcast.
mono sound during stereo broadcast.
VOL
VOL
OK
14.LIST
12
PR
displays
the programme table.
15.TELETEXT BUTTONS
These buttons
For further
are
details,
PR-
(option)
used for teletext.
see
PR+SWAPINPUT
4
the 'Teletext' section.
PSM
Note : In teletext mode, the PR+/-, SWAP and INPUT buttons
used for teletext function.
are
SSM
13
DUAL
5
SIZE
STILL POSITION9/4 PIP
6
PIP
Battery
START LENGTHSP/LPON/OFF
installation
The remote control handset is
To load the
batteries,
battery compartment.
polarity symbols( + and
powered by
two AA
type batteries.
turn the handset over and slide open the
Install two batteries as indicated by the
-
)
marked inside the
7
V
C
R
CH+
CH
QSR
REW
PLAY
P/STILLSTOP
FF
REC
compartment.
(Without TELETEXT)
Note : To avoid damage from possible battery leakage, remove the
batteries if you do not plan to use the remote control handset for an
extended period of time.
5
Location and function of controls
Front
panel
CF-29C82 series
*
EYE
MENU
POWER
VIDEOL / MONO
R
O K
VOL
PR
STAND
BY
S-VIDEO
AUDIO
AV3
1
10
23
4567
89
CF-29H20, CF-29/25C61 series
*
N
ATURAL ALGORITHM EYE
AV3
(L/MONO)-AUDIO-(R)
VIDEO
S-VIDE O
MENU
POWER
OK
-VOL+
-PR+
STAND BY
12
*
3
4567
8
910
CF-29H60 series
N
AV3
VIDEO
POWER
1
*
MENUOK
(L/MONO)-AUDIO-(R)
2
VOL
PR
S-VIDE O
3
4567
ATURAL ALGORITHM
EYE
STAND BY
89
10
CF-34C60/61/62/63 series
AV3
VIDEO
AUDIO
L/MONO
POWER
STAND BY
R
S-VIDEO
NATURAL
EYE
ALGORITHM
MENUOK
12
3
VOL
PR
4567
9
8
10
1. MAIN POWER
switches the set on or off.
2. AUDIO/VIDEO IN SOCKETS (AV3)
Connect the audio/video out sockets of external
equipment
to
these sockets.
3. S-VIDEO/AUDIO IN SOCKETS (S-AV)
Connect the video out socket of an S-VIDEO VCR to the SVIDEO socket. Connect the audio out sockets of the S-VIDEO
VCR to the audio sockets as in AV3.
4.MENU
calls or clears the main menu.
5. OK
accepts your selection or displays the current mode.
6.VOLUME UP/DOWN
adjusts the volume.
adjusts
menu
settings.
7.PROGRAMME UP/DOWN
switches the set on from standby.
selects a programme or a menu item.
8.STANDBY INDICATOR
illuminates red when the set is in standby mode.
9.REMOTE CONTROL SENSOR
10. NATURAL ALGORITHM EYE (option)
adjusts picture according to the surrounding conditions.
6
Basic
operation
Contents
On and off
1.Press the main power button to switch the set
2.
on.
If the set is in
standby mode, press the POWER, ¡a/¡a
NUMBER buttons on the remote control handset to switch it
or
on
fully.
3.
Press the POWERbutton
The set reverts to
on
the remote control handset.
mode.
standby
4.Press the main power button
again
to switch the set off.
Note : If, while the set is switched on, the mains plug is disconnected the set will switch to standby or power on when the mains
plug is replaced in the mains power socket.
Programme
You
select
can
selection
programme number with the
a
¡a/¡a
or
POWER
MUTE
1
2
3
4
5
6
SRS
7
8
9
TV/AV
NUMBER
MENU
0
buttons.
Volume
adjustment
Press the
¢¸/¢º
button to
adjust
the volume.
PR
VOL
OK
Mute function
PR
Press the MUTEbutton. The sound is switched off and the
appears. You
VOL
can
cancel it
by pressing
the
display
MUTE, ¢¸/¢º, SSM,
DUALor SRSbutton.
SSM
On
screen
This is
language
function. The
optional
language.
in the desired
1.
selection
Function
be
display
displayed
language.
the Main
icon
3.Press the OK button to
on
the
screen
menu.
button to select the Station
¢¸/¢º
menu
(option)
menu can
First select your
Press the MENUbutton to
2.Press the
DUAL
menu
icon
or
.
display
the Stationmenu
or
Special
functionmenu.
4.Press the
5.Press the
All the
¡a/¡a
button to select
¢¸/¢º
button to select the desired
Language.
language.
will appear in the selected language.
6.Press the OKor TV/AVbutton to return to normal TV viewing.
on screen
displays
7
On
screen menus
The
dialogue
operator
an
also
Contents
between you and your set takes place on screen with
The buttons required for the operating steps are
menu.
displayed.
Menu selection
Press the MENUbutton to display the Main menu.
Press the ¢¸/¢º button to select each menu icon.
The selected menu icon changes from green to purple.
3.Press the OKbutton to display the sub menu.
4.Press the ¡a/¡a button to select a menu item.
The selected menu item changes from green to purple.
5. Press the ¢¸/¢º button to change the setting of a menu item or
OKbutton to display the sub menu.
Note :
a.
The menus automatically disappear in about 1 minute if you do
not press a button.
b. In the AV mode, the Station menu icon is not selected.
c. In the teletext mode, menus are not displayed.
d. In some models, the menu item Language is displayed on the
Special function menu or is not displayed on the screen menu.
e. In some models, the menu item Use is displayed on the screen
1.
2.
MENU
menu.
Station
AutoOprogramme
ManualOprogramme
ProgrammeOedit
LanguageOOOOEnglish
PR
VOL
OK
OK
¡a¡a
VOL
Station
TV/AV
menu
(TV mode)
PR
Picture
Standard
Game
Mild
Cinema
User
Eye
¡a¡a
OK
Picture
TV/AV
menu
Sound
EqualizerOOOOOOCinema
Station
BalanceOOOOOOOOOOOO00
¢¸¢º
Main
OK
TV/AV
SuperOwooferOOOOOOOOn
SRSOOOOOOOOOOOOOOOOff
menu
¡a¡a ¢¸¢º
Sound
OK
TV/AV
menu
SpecialOfunction
InputOOOOOOOOOOOOOOTV
ChildOlockOOOOOOOOOff
AutoOsleepOOOOOOOOOff
BlueObackOOOOOOOOOOff
OffOtimerOOOOOOO__:__
OnOtimerOOOOOOOO__:__
TiltOOOOOOOOOOOOOOO00
Demonstration
¡a¡a ¢¸¢º
OK
Function
8
TV/AV
menu
TV stations
Setting up
Up to 100 TV stations can be stored in this set by programme
numbers (00 to 99). Once you have preset the stations, you will be
able to use the ¡a/¡a or NUMBER buttons to scan the stations you
programmed.
Stations
can
be tuned
Auto programme
All stations that
can
recommended that you
Press
2.Press
3.Press
4.Press
1.
using
automatic
or
manual modes.
be received
use
are
stored
auto programme
during
by
display
menu
OK
TV/AV
this method. It is
installation of this set.
the MENUbutton to display the Main menu.
the ¢¸/¢º button to select the Station menu icon
the OK button to display the Stationmenu.
the ¡a/¡a button to select Auto programme.
5.Press the OK button to
Station
Station
AutoOprogramme
ManualOprogramme
ProgrammeOedit
LanguageOOOOEnglish
¡a¡a
tuning
Contents
.
the Auto programmemenu.
AutoOprogramme
StorageOfromOOOOOOOO01
SystemOOOOOOOOOOOOAUTO
1
2
3
4
5
6
7
8
9
TV/AV
Start
MENU
0
¡a¡a ¢¸¢º
6.
Press the
OK
TV/AV 0~9
button to select Storage from. Select the
programme number with the ¢¸/¢º button or
NUMBER buttons. Any number under 10 is entered with a
numeric '0' in front of it, i.e. '05' for 5.
Press the ¡a/¡abutton to select System.Select a TV system
with the ¢¸/¢º button; AUTO, M, BG, Ior DK.
Press the ¡a/¡a button to select Start.
Press the OKbutton to begin auto programming.
¡a/¡a
beginning
7.
8.
9.
PR
VOL
OK
VOL
PR
AutoOprogramme
StorageOfromOOOOOOOO04
SystemOOOOOOOOOOOOAUTO
PR.O27OOCHO30OOOOOO{{{
..................
OK
All receivable stations are stored.
The programme number and channel number being searched
appear below the display System. The channel number is
assigned and stored with CHfor television or CC for cable
channels.
To
stop
auto
programming,
press the OKbutton.
When auto programming is completed, the Programme edit
mode appears on the screen with the channel number. See the
'Programme edit' section to edit the stored programme.
10. Press the TV/AVbutton to return to normal TV
viewing.
Note: If there is a sound noise in some channels after auto
is completed, re-adjust System to M, BG, I or DK in
Manual programme tuning. Refer to 'Manual programme tuning.'
programming
9
TV stations
Setting up
Station
Station
Manual programme
AutoOprogramme
ManualOprogramme
ProgrammeOedit
LanguageOOOOEnglish
Manual programme lets you manually tune and arrange the
stations in whatever order you desire. Also you can assign a
menu
¡a¡a
OK
station
tuning
with five characters to each programme number.
name
TV/AV
1. Press the MENUbutton to
2.Press the
3.Press the OK button to
4.Press the
¡a/¡a
display
the Main
menu.
button to select the Station
¢¸/¢º
display
menu
icon
.
the Stationmenu.
button to select Manual programme.
display the Manual programme
5.Press the OK button to
menu.
1
2
3
4
5
6
7
8
9
ManualOprogramme
SystemOOOOOOOOOOOOOOBG
ChannelOOOOOOOV
UHFO01
SearchOOOOOOOOOOOOO{{{
FineOOOOOOOOOOOOOOO{{{
NameOOOOOOOOOOOOOCHO01
AutoOAVOOOOOOOOOOOOOff
StorageOOOOOOOOOOOOO12
OK
¡a¡a ¢¸¢º
TV/AV
MENU
0
6.Press the
¡a/¡a button to select System.Select a TV system
¢¸/¢º button; M, BG, Ior DK.
7.Press the ¡a/¡a button to select Channel. Press the ¢¸/¢º
button to select V/UHFor CATVas required. If possible, then
select the channel number directly with the NUMBER buttons.
8.Press the ¡a/¡a button to select Search.
9.Press the ¢¸/¢º button to commence searching. If a station is
with the
PR
VOL
OK
PR
VOL
found the search will
stop.
10.If this station is the
one required, press the ¡a/¡a button to
Select
the desired programme number with
Storage.
the ¢¸/¢º button or NUMBER buttons. Any number under 10 is
select
entered with
a
numeric '0' in front of
11.Press theOKbutton to store it. The
12.To store another station
Assigning
station
a
1.Press the
¡a/¡a
it, i.e.
'05' for 5.
display
repeat steps
Stored will appear.
6 to 11.
name
button to select Name.
2.To select your desired first
¡a button. You can use the
character, press the ¢º button then
Ato Z, a blank,
and
+,
alphabet
.,
_
the numeric 0to 9.
With the
¡a
button you
3.Select the next
can
select in the
opposite
direction.
the ¢º button and then
take your choice of the second character, and so on.
4.Press the OKbutton to select Storage. Select the desired
position by pressing
programme number with the
buttons.
¢¸/¢º
5.Press theOKbutton to store it. The
6.To
10
assign
another station
name
button
display
or
NUMBER
Stored will appear.
repeat steps
1 to 5.
TV stations
Setting up
Auto AV setting (option)
Auto AV is optional function. If your VCR outputs a switching
voltage when it is switched to playback, select Auto AV On with
the VCR connected to Euro scart socket. The set is
switched to AV-1 mode when
an
AV
signal
is
input.
automatically
keep
menu
AutoOprogramme
ManualOprogramme
ProgrammeOedit
LanguageOOOOEnglish
But if you want
watching TV mode, set Auto AV to Off.
¡a/¡a button to select Auto AV.
2.Press the ¢¸/¢º button to select Onor Off.
3.Press the ¡a/¡a button to select Storage. Select the desired
programme number with the ¢¸/¢º button or NUMBER buttons.
4.Press theOKbutton. The display Stored will appear.
to
Station
Station
on
¡a¡a
OK
TV/AV
1.Press the
5.To set another programme
repeat steps
1 to 4.
Press the TV/AVbutton to return to normal TV
Fine
1
2
3
4
5
6
7
8
9
viewing.
tuning
Normally
fine
1.Repeat
TV/AV
MENU
0
tuning
is
only
necessary if
'Manual programme
reception
tuning' steps
is poor.
1 to 5.
ManualOprogramme
SystemOOOOOOOOOOOOOOBG
ChannelOOOOOOOV
UHFO01
SearchOOOOOOOOOOOOO{{{
FineOOOOOOOOOOOOOOO{{{
PR
VOL
NameOOOOOOOOOOOOOCHO01
AutoOAVOOOOOOOOOOOOOff
OK
StorageOOOOOOOOOOOOO12
¡a¡a ¢¸¢º
2.Press the
¡a/¡a
¡a/¡a
TV/AV
button to select Fine. Press the
fine tune for the best
3.Press the
OK
picture
VOL
PR
¢¸/¢º
button to
and sound.
button to select
Storage.
Select the desired
programme number with the ¢¸/¢º button or NUMBER buttons.
4.Press theOKbutton. The display Stored will appear.
5.Press the TV/AVbutton to return to normal TV
The
finely tuned programme
during programme selection.
will be indicated
viewing.
by yellow
number
11
Setting up
Station
menu
Programme
Station
AutoOprogramme
ManualOprogramme
ProgrammeOedit
LanguageOOOOEnglish
¡a¡a
OK
edit
This function enables you to delete or skip the stored programmes.
Also you can move some stations to other programme numbers or
copy to the next programme numbers.
1. Press
2.Press
3.Press
4.Press
5.Press
TV/AV
TV stations
the MENUbutton to display the Main menu.
the ¢¸/¢º button to select the Station menu icon
the OK button to display the Stationmenu.
the ¡a/¡a button to select Programme edit.
the OK button to display the Programme editmenu.
.
ProgrammeOedit
OO05OCHO05
01OCHO01OOO06OCHO07
¢º 00OCHO05
02OCHO02OOO07OCHO13
1
2
03OCHO03OOO08OCHO01
3
04OCCO30OOO09OCHO04
? Delete
4
5
? Move
6
¡a¡a ¢¸¢º
7
8
TV/AV
9
Deleting
MENU
?
Copy
?
Skip
TV/AV
a
programme
programme to be deleted with the
2.Press the RED button twice.
1.Select
0
OK
a
¡a/¡a
or
¢¸/¢º
The selected programme is deleted and all the
programmes are shifted up one position.
3.Press theTV/AVbutton to return to normal TV
PR
VOL
OK
PR
VOL
Copying
a
1.Select
a
programme
programme to be copied with the ¡a/¡a
2.Press the GREEN button.
All the following programmes are shifted down
3.Press theTV/AVbutton to return to normal TV
Moving
button.
following
viewing.
or
¢¸/¢º
button.
position.
viewing.
one
a
programme
programme to be moved with the ¡a/¡a or ¢¸/¢º button.
2.Press the YELLOW button. The selected programme is in yellow.
3.Move the programme to the desired programme number with
the ¡a/¡a button.
1.Select
a
The selected programme
the direction selected.
moves
4.Press the YELLOW button
again
through
the programme list in
to release this function.
5.Press theTV/AVbutton to return to normal TV
Skipping
a
1.Select
a
programme
programme to be
2.Press the BLUE button.
skipped
with the
¡a/¡a
viewing.
or
¢¸/¢º
button.
The skipped programme turns to blue.
3.Press the BLUE button again to release the
skipped programme.
The programme returns to green and the skip is cancelled.
4.Press theTV/AVbutton to return to normal TV viewing.
During
programme selection, with the ¡a/¡a button the
can not be found. If you want to find the
programme
skipped
skipped
programme directly enter the programme number with the
NUMBER buttons or select it in the programme edit or table
mode.
12
Picture
You
adjustment
select your preferred picture setting; Standard, Game,
as you prefer. Also you can adjust picture contrast,
brightness, colour intensity, sharpness and tint (NTSC input only)
to the levels you prefer.
Contents
can
Mild, Cinema,
Press the MENUbutton to display the Main menu.
2.Press the ¢¸/¢º button to select the Picture menu icon
3.Press the OK button to display the Picturemenu.
Picture
Picture
menu
Standard
Game
Mild
Cinema
User
1.
Eye
.
¡a¡a
OK
TV/AV
Standard, Game, Mild, Cinema, User
1.Press the ¡a/¡a button to select Standard, Game, Mild,
Cinema or User.
2.Press the OK button.
Picture
ContrastOOOOOOOOOOO100
BrightnessOOOOOOOOOO50
EYE
ColourOOOOOOOOOOOOOO50
SharpnessOOOOOOOOOOO50
TintOOOOOOOOOOOOOOOO00
YNROOOOOOOOOOOOOOOOOff
...................
TV/AV
TV/AV
3.Press the ¡a/¡a button to select the desired picture item.
4.Press the ¢¸/¢º button to make appropriate adjustments.
5.Press the OK button. In User menu only, the display Stored
will appear.
MENU
¡a¡a ¢¸¢º
OK
These picture settings, except for User, are temporarily stored
and if the TV switches off and then on, the adjusted level
returns to the factory preset settings.
Note
a.
b.
c.
PR
:
VOL
be selected for the NTSC only.
The picture item YNR reduces picture noise if you select On.
YNR is optional function.
In some models, it is impossible to operate it.
Tint
can
OK
VOL
PR
Eye (option)
This set will
automatically adjust the picture according to the
surrounding conditions. This will enable you to enjoy the most
suitable picture according to the surroundings.
1.Press the ¡a/¡a button to select Eye.
2.Press the OK button.
Or you can display the Eye mode by
pressing
PSM
the EYEbutton
once.
Eye
EyeOOOOOOOOOO
On
ContrastOOOOOOOOOOO100
BrightnessOOOOOOOOOO50
ColourOOOOOOOOOOOOOO50
SharpnessOOOOOOOOOOO50
RedOOOOOOOOOOOOOOOOO
Blue
¢¸¢º
OK
TV/AV
3.Press the ¢¸/¢º button to select On
4.Press the OK button.
or
Off.
To recall your preferred setting, press the PSMbutton until the
desired picture (Standard, Game, Mild, Cinema, User)
appears.Standard, Game, Mildand Cinema are programmed
at the factory for good picture reproduction appropriate to each
programme chacracter.
13
Sound
Sound
menu
Sound
Sound
EqualizerOOOOOOCinema
You
BalanceOOOOOOOOOOOO00
SuperOwooferOOOOOOOOn
SRSOOOOOOOOOOOOOOOOff
¡a¡a ¢¸¢º
OK
TV/AV
adjustment
Contents
adjustment
select your preferred sound setting; Cinema, Sports,
as you prefer. Also you can adjust the sound frequency to the levels you prefer. The SRS (Sound Retrieval System) creates an all around sound as in a concert hall and super
woofer sound stresses and emphasizes bass.
can
Music, Speech,
1.
Press the MENUbutton to display the Main menu.
2.Press the ¢¸/¢º button to select the Sound menu icon
3.Press the OK button to display the Soundmenu.
Equalizer
1.Press the
2.Press the
.
¡a/¡a button to select Equalizer.
¢¸/¢º button to select Cinema, Sports, Music,
Speech or User.
3.Press the OK button
In
SRS
of Cinema, Sports, Music, Speech, each corresis displayed on the screen. Cinema, Sports,
Musicand Speech are programmed at the factory for good
sound reproduction appropriate to each programme character.
TV/AV
In case of User, select the sound band with the ¢'/¢"button and
make appropriate sound level with the ¡a/¡a button as you prefer.
case
ponding equalizer
Equalizer
MENU
Equalizer
Cinema
Sports
Sports
0
Music
Speech
0.1 0.3 1.0
VOL
OK
PR
VOL
OK
-10
User
-10
User
PR
0
Music
Speech
¡a¡a
+10
+10
Cinema
3.3
0.1 0.3
10K
¡a¡a ¢¸¢º
TV/AV
(Cinema, Sports, Music,
Speech)
4.Press the OK button. In
will appear.
OK
1.0 3.3
10K
TV/AV
(User)
case
of User
only,
the
display
Stored
Balance
1.Press the ¡a/¡a button to select Balance.
2.Press the ¢¸/¢º button to adjust the balance level.
3.Press the OKbutton. The display Stored will appear.
SSM
Super woofer (option)
1.Press the ¡a/¡abutton
to select Super woofer.
2.Press the ¢¸/¢º button to select On or Off.
3.Press the OKbutton. The display Stored will appear.
Option
:
In some models, connect the woofer connector on the back to the
WOOFERsocket on the back of the set before adjusting the sound.
SRS
1.Press the ¡a/¡a button to select SRS.
2.Press the ¢¸/¢º button to select On or Off.
3.Press theTV/AVbutton once or OK button twice to return to
normal TV viewing.
Or directly select the SRS On or Offmode with the SRSbutton
alternately as shown below then press the OKbutton to return to
normal TV viewing.
On
SRS
To recall your preferred setting, press the SSMbutton until the
desired sound (Cinema, Sports, Music, Speech, User)
appears.
14
Sound
Stereo/Dual
adjustment
reception
When a programme is selected, the sound information for the
station appears after the programme number and station name
disappear.
Broadcast
On Screen
Mono
MONO
Stereo
STEREO
Dual
DUAL I
Display
Mono sound selection
In stereo
reception if the stereo signal is weak, you can switch to
by pressing the DUAL button. In mono reception the depth
of sound is improved. To switch back to stereo, press the DUAL
button again.
mono
Language selection for dual language broadcast
If a programme received in two languages (dual language), you can
switch to DUAL I, DUAL II or DUAL I II by pressing the DUAL button
repeatedly.
DUAL I sends the primary broadcast language to the loudspeakers.
DUAL II sends the secondary broadcast language to the loudspeakers.
DUAL I II sends a separate language to each loudspeaker.
NICAM
reception (option)
NICAM is optional function. If your set is equipped with the receiver
for NICAM reception, the high quality NICAM (Near Instantaneous
Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the type of received
broadcast as follows by pressing the DUAL button repeatedly.
DUAL
When NICAM mono is received, you can select NICAM
MONO or FM MONO.
2. When NICAM stereo is received, you can select NICAM
STEREO or FM MONO. If the stereo signal is weak, switch to
FM mono.
3. When NICAM dual is received, you can select DUAL I, DUAL
II or DUAL I II or MONO. When FM mono is selected the
display MONO appears on the screen.
1.
Sound output selection
In AV
mode, you
can
select
output sound for the left and right
loudspeakers.
Repeatedly
L+R
:
L+L
:
R+R
:
press the DUAL button to select the sound output.
Audio signal from audio L input is sent to left loudspeaker
and audio signal from audio R input is sent to right loud-
speaker.
Audio signal
speakers.
Audio signal
speakers.
from audio L
input
is sent to left and
right
loud-
from audio R
input
is sent to left and
right
loud-
15
Other functions
Special
function
menu
SpecialOfunction
InputOOOOOOOOOOOOOOTV
ChildOlockOOOOOOOOOff
AutoOsleepOOOOOOOOOff
BlueObackOOOOOOOOOOff
OffOtimerOOOOOOO__:__
OnOtimerOOOOOOOO__:__
TiltOOOOOOOOOOOOOOO00
Demonstration
¡a¡a ¢¸¢º
OK
TV/AV
Contents
TV and AV modes
Inputs can be set for TV or AV mode. AV mode is used when a video
cassette recorder (VCR), or other equipment is connected to the set.
Note : When a VCR is connected via the aerial socket the set is used
in TV mode. See the 'Connection of external equipment' section.
1. Press the MENUbutton to display the Main menu.
2.Press the ¢¸/¢º button to select the Function menu icon
3.Press the OK button to display the Special functionmenu.
4.Press the ¡a/¡a button to select Input.
5.Press the ¢¸/¢º button to select TV,AV-1,AV-2,AV-3 orS-AV.
The four AV modes are :
AV 1 : VCR connected to the Euro scart socket on the back
AV 2 : VCR connected to the AV2sockets on the back
AV 3 : VCR connected to the AV3sockets on the front panel
S-AV : VCR connected to the AUDIOand S-VIDEOsockets on
the front panel
6.Press the OKor TV/AVbutton.
To return to TV mode from AV mode press the ¡a/¡a or NUMBER buttons.
.
1
2
3
4
5
6
7
8
9
TV/AV
Alternatively
MENU
0
you
TV/AVbutton.
can
select the TV
or
AV mode
by pressing
the
Child lock
The TV can be set so that the remote control handset is needed to
control it. This feature can be used to prevent unauthorised viewing.
PR
VOL
OK
PR
1. Press the MENUbutton to display the Main menu.
2.Press the ¢¸/¢º button to select the Function menu icon
3.Press the OK button to display the Special functionmenu.
4.Press the ¡a/¡a button to select Child lock.
5.Press the ¢¸/¢º button on the remote control handset to select On.
6.Press the OKor TV/AVbutton to return to normal TV viewing.
.
VOL
With the lock on, the display Child lock appears on the screen if
any button on the front panel is pressed while viewing the TV.
Auto
sleep
If you select Auto
to standby mode
sleep On the set will automatically switch itself
approximately ten minutes after a TV station
stops broadcasting.
1. Press the MENUbutton to display the Main menu.
2.Press the ¢¸/¢º button to select the Function menu icon
3.Press the OK button to display the Special functionmenu.
4.Press the ¡a/¡a button to select Auto sleep.
5.Press the ¢¸/¢º button on the remote control handset to select On.
6.Press the OKor TV/AVbutton to return to normal TV viewing.
.
Blue back
(option)
Blue back is an optional function.
If you have set Blue back to On, the blue background appears
the screen when there is no broadcasting signal.
on
1. Press the MENUbutton to display the Main menu.
2.Press the ¢¸/¢º button to select the Function menu icon
3.Press the OK button to display the Special functionmenu.
4.Press the ¡a/¡a button to select Blue back.
5.Press the ¢¸/¢º button to select On.
6.Press the OKor TV/AVbutton to return to normal TV viewing.
Note : This function does not operate while the sub picture is
displayed on the screen.
.
16
Other functions
Off timer
The off timer automatically switches the set to
preset time elapses.
standby
after the
SpecialOfunction
Special
InputOOOOOOOOOOOOOOTV
function
ChildOlockOOOOOOOOOff
menu
AutoOsleepOOOOOOOOOff
BlueObackOOOOOOOOOOff
1. Press the MENUbutton to display the Main menu.
2.Press the ¢¸/¢º button to select the Function menu icon
3.Press the OK button to display the Special functionmenu.
4.Press the ¡a/¡a button to select Off timer.
5.Set the desired time period with the ¢¸/¢º button.
6.Press the OKor TV/AVbutton to return to normal TV viewing.
.
OffOtimerOOOOOOO__:__
OnOtimerOOOOOOOO__:__
TiltOOOOOOOOOOOOOOO00
Demonstration
¡a¡a ¢¸¢º
OK
TV/AV
On timer
The set
automatically
switches
on
after the
preset time elapses.
POWER
1. Press the MENUbutton to display the Main menu.
2.Press the ¢¸/¢º button to select the Function menu icon
3.Press the OK button to display the Special functionmenu.
4.Press the ¡a/¡a button to select On timer.
5.Set the desired time period with the ¢¸/¢º button.
6.Press the OKor TV/AVbutton to return to normal TV viewing.
.
TV/AV
You can set the on/off timer from 10 minutes up to 12 hours 50
minutes in 10 minutes steps. The timer begins to count down from
the selected time period.
Note :
a. This set must be put into standby mode with the POWER button
on the remote control to operate the on timer function.
b. Two hours after the set is switched on by the on timer function it
will automatically switch back to standby mode unless a button
has been pressed.
c.
To view the remaining on/off time, select the Special function menu.
d. To cancel the set on/off time, set the on/off timer to --:--.
e.
When you switch the main power off, the on/off time is reset.
Tilt
MENU
PR
VOL
OK
VOL
PR
(option)
Tilt is optional function.
The TV picture may tilt to the left or right if the TV set moves to
another position. This function can be used to compensate the tilt.
1. Press
2.Press
3.Press
4.Press
5.Press
6.Press
the MENUbutton to display the Main menu.
the ¢¸/¢º button to select the Function menu icon
the OK button to display the Special functionmenu.
the ¡a/¡a button to select Tilt.
the ¢¸/¢º button to adjust the tilt.
the OKor TV/AVbutton to return to normal TV viewing.
.
Auto demonstration
Auto demonstration allows you to review all the
med in the set.
1. Press
2.Press
3.Press
4.Press
5.Press
stop
program-
the MENUbutton to display the Main menu.
the ¢¸/¢º button to select the Function menu icon
the OK button to display the Special functionmenu.
the ¡a/¡a button to select Demonstration.
the OKbutton to start the demonstration.
When the demonstration reaches the last
from the beginning.
To
menus
auto
display,
it starts
.
again
demonstration, press any button.
17
Other functions
Calling
You
programme table
a
can
displaying
check the programmes stored in the memory
the programme table.
by
programme table
Displaying
Press the LISTbutton.
The programme table appears on the screen. One programme
table contains ten programmes as below.
ProgrammeOtable
¢"00OCHO05 OOO05OCHO05
1
2
3
4
5
6
7
8
9
01OCHO01OOO06OCHO07
02OCHO02OOO07OCHO13
03OCHO03OOO08OCHO01
04OCCO30OOO09OCHO04
¡a¡a ¢¸¢º
OK
TV/AV
TV/AV
0
Note
:
a.
You may find some blue programmes.
Programme edit mode.
b.
Some programme numbers with the mark
programme table indicate there is
no
They
station
are
-----
name
skipped
in the
shown in the
assigned.
PR
VOL
OK
Selecting
VOL
a
programme in the programme table
Select upper
PR
or
lower programme with the
¡a/¡a
button and left
or
right programme with the ¢¸/¢º button. The colour of normal
programmes is green and skipped programme is blue.
LIST
Then press the OKbutton.
The set switches to the chosen programme number.
Paging through
There
are
programme table
ten programme table pages in which contain
programmes.
the pages.
Switching
a
Pressing
the
¡a/¡a
or
¢¸/¢º
18
repeatedly
100
turns
back to TV mode
Press the TV/AVor NUMBER buttons
mode.
button
during
programme table
PIP
Option:
PIP is optional function,
so
that
operation (option)
only
the set with PIP function
Contents
can
operate.
PIP
(Picture
in
Picture) displays
a
picture
within
a
picture.
On and off
Press the PIP button to switch on the sub
Press this button again to switch it off.
Programme
selection for sub
picture.
picture
Press the PR +/-buttons. The selected programme number is
displayed at the left upper side of sub picture.
Input
mode selection for sub
picture
Press the INPUTbutton while the sub
main picture.
picture
remains within the
Each time this button is pressed, each input mode for the sub
is displayed as shown below at the left upper side of sub
picture
picture.
Programme
Swapping
number
AV-2
between main and sub
Press theSWAPbutton to
Sub
AV-1
picture
exchange
AV-3
PIP
S-AV
pictures
the main and sub
pictures.
size
PR-
PR+SWAPINPUT
SIZE
STILLPOSITION9/4 PIP
press the SIZEbutton to select the desired sub picture
size. The sub picture appears as 1/4 size of the main picture,
followed by 1/9.
Repeatedly
Sub
picture
freeze
Press the STILLbutton to freeze motion of the sub
Press this button again to restore motion.
Sub
picture.
PIP
picture position change
Press the POSITIONbutton repeatedly until desired
achieved. The sub picture moves clockwise.
Programme
position
is
scan
This function enables you to search all the stored stations on 9 or 4
sub pictures and see your favorite station by exchanging the main
and sub pictures.
Press the 9/4 PIP button. 9 sub pictures appear and search all the
stored stations.
Press this button again. At this time 4 sub pictures search them.
Press the 9/4 PIPbutton once more. The 9 or 4 sub pictures switch
off.
If you press the SWAPbutton while the desired station is being
are exchanged so the station
being searched appears on the main picture.
searched, the main and sub picture
19
Teletext
Teletext is
system
can
(option)
optional function,
Contents
therefore
only
a
set with the teletext
receive the teletext broadcast.
Teletext is
a free service broadcast by most TV stations which
gives up-to-the-minute information on news, weather, television
programmes, share prices and many other topics.
The teletext decoder of this TV
can
support the LIST, TOP and
FASTEXT systems. LIST
pages which are selected
number. TOP and
1
2
3
4
5
6
7
8
9
0
TEXT
(standard teletext) consists of a number of
by directly entering the corresponding page
FASTEXT are more modern methods allowing quick
and easy selection of teletext information.
Switch on/off
TV/AV
Press the TEXTbutton to switch to teletext. The initial page
selected page appears on the screen.
Two page numbers, TV station name, date and time
on
the
are
or
last
displayed
headline. The first page number indicates your
while the second shows the current page displayed.
screen
selection,
Press the TEXTor TV/AVbutton to switch off teletext. The
PR
mode reappears.
PR
LIST mode
If the TV is in TOP
or
FASTEXT
mode, press the
previous
button to
switch to LIST mode.
Page
1.
M
selection
Enter the desired page number as a three digit number with the
NUMBER buttons. If during selection you press a wrong
number, you must complete the three digit number and then reenter the correct page number.
2.
20
The
¡a/¡a button
following page.
can
be used to select the
preceding
or
Teletext
(option)
Programming a colour button
Four teletextpage numbers of your choice can be colour coded and
easily selected by pressing the corresponding coloured button on
the remote control handset.
1.
Using
the NUMBER
buttons, select the page you wish
to
programme.
2. Wait until the page is displayed on the screen and press the OK
button. The page numbers in the colour boxes along the bottom
3.
of the
screen
Press
a
change
to "000?".
colour button to store the page number. From
select this page with the same coloured button.
you can
4. The three other coloured buttons
programmed
are
in the
now
same
on,
way.
1
2
3
4
5
6
7
8
9
TOP mode
The
user
guide displays
the bottom of the
four
fields-red, green, yellow
field denotes the next group
and the blue field indicates the next block.
screen.
Group/block/page
The
and blue at
yellow
0
selection
With theBLUEbutton you can progress from block to block.
2. Use the YELLOWbutton to proceed to the next group with
1.
PR
automatic overflow to the next block.
3.
With the GREENbutton you can proceed to the next existing
page with automatic overflow to the next group. Alternatively the
¡a button
can
be used.
4.TheREDbutton
the
¡a
button
can
permits
to return to
previous
selection.
OK
PR
Alternatively
be used.
Direct page selection
Corresponding to the LIST teletext mode, you can select a page by
entering it as a three digit number using the NUMBER buttons in
TOP mode.
FASTEXT mode
The teletext pages are colour coded along the bottom of the screen
and are selected by pressing the corresponding coloured button.
Page
1.
selection
Press the
button to select the index page.
select the pages which are colour coded
bottom line with the same coloured buttons.
2.
You
3.
Corresponding to the LIST teletext mode, you can select a page
by entering its three digit page number with the NUMBER
4.
The
can
along
the
buttons in FASTEXT mode.
¡a/¡a button
following page.
can
be used to select the
preceding
or
21
Teletext
Special
(option)
teletext functions
REVEAL
Press this button to
as
display concealed information,
or puzzles.
again to remove the information
such
solutions of riddles
Press this button
the
from
display.
EXPAND
(SIZE)
height text.
this button to enlarge the top half of the page.
this button again to enlarge the bottom half of
Selects double
Press
Press
page.
Press this button
again
to return to the normal
the
display.
UPDATE
Displays
the
top
the TV
picture
on
the
screen
while
for
waiting
teletext page. The display
will appear at the
left hand corner of the screen. When the updated
new
page is available then
page number.
Press this button to view the
HOLD
will
display
updated
change
to the
teletext page.
(STOP)
the automatic page change which will occur if a
teletext page consists of 2 or more sub pages. The
Stops
number of sub pages and the sub page displayed is,
usually, shown on the screen below the time. When this
button is
pressed
left-hand
corner
change
the
stop symbol is displayed
of the
at the
top
and the automatic page
screen
is inhibited.
To continue press this button
again.
TX
T
MIX
Displays
picture.
the teletext pages
To switch the TV
picture
superimposed
off press this button
on
the TV
again.
TIME
When
viewing a
display the time
screen.
TV programme, press this button to
at the top right hand corner of the
Press this button
the teletext
again
to remove the
display.
In
mode, press this button
to select a sub page
number. The sub page number is displayed at the
bottom of the
screen.
To hold
or
press the RED/GREEN, ¡a/¡a
Press again to exit this function.
22
the sub page,
NUMBER buttons.
change
or
Connection of external
You
can
connect additional
such
equipment,
as
equipment
Contents
VCRs, camcorders
etc. to your set. Here shown may be somewhat different from your
set.
Aerial socket
1.
Connect the RF out socket of the VCR to the aerial socket
on
the back of the set.
2.
OUTIN(AV2)
VIDEO
Connect the aerial cable to the RF aerial in socket of the VCR.
3.Store the VCR channel
L
ANT IN
75Ω
1
AUDIO
R
WOOFER
desired programme number using
the 'Manual programme tuning' section.
4. Select the programme number where the VCR channel is stored.
5.Press the PLAYbutton
on a
on
the VCR.
VCR
Euro scart socket
1.
Connect the Euro scart socket of the VCR to the Euro scart
OUTIN(AV2)
VIDEO
socket of the set.
2.
Press the PLAY button
L
on
ANT IN
75Ω
the VCR.
If your VCR outputs a switching
AV-1 mode automatically.
AUDIO
R
voltage
WOOFER
the set will switch to
Otherwise press the TV/AVbutton on the remote control
handset to select AV-1. The VCR playback picture appears on
the
1
VCR
screen.
You
can
also record programmes received
by
the TV
on
video
tape.
Note
In
models, signal type RGB input is optional function.
i.e. the signals red, green and blue can only be
RGB,
Signal type
selected for the Euro scart socket. These signals are transmitted,
for example, by a computer, pay TV decoder, game machine or
photo CD unit, etc.
:
some
OUTIN(AV2)
VIDEO
L
1
ANT IN
75Ω
AUDIO
R
WOOFER
Audio/Video in/out sockets
1.
Connect the audio/video out sockets of the VCR to audio/video
VCR
in sockets of the set and in sockets of the VCR to out sockets of
the set.
2.
If the VCR is connected to the AV sockets on the back, press
the TV/AVbutton to select AV-2. You should select AV-3if
AV3sockets
3.
on
the front
Press the PLAYbutton
The VCR
You
tape
panel
on
playback picture
are
connected to the VCR.
appears
on
VIDEOL /MONO
R
S-VIDEO
AUDIO
AV3
the
screen.
also record programmes received
via audio/video out sockets.
can
POWER
the VCR.
by
the TV
on
video
VCR
23
Connection of external
equipment
S-video/Audio in sockets
(S-AV)
When
POWER
VIDEO L/MONO
R
S-VIDEO
AUDIO
connecting an S-VIDEO VCR to
picture quality will be further improved.
the S-VIDEO
socket, the
AV3
1.
Connect the S-video socket of the VCR to the S-VIDEO socket
on
the control
panel
of the set.
2.
Connect the audio cable from the S-VIDEO VCR to the AUDIO
3.
Select S-AV
4.
Press the PLAY button
sockets
S-VIDEO VCR
on
The VCR
the control
panel
by pressing the
on
playback picture
of the set.
TV/AV button
repeatedly.
the VCR.
appears
on
the
screen.
: If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO socket on the control panel of the set.
Note
Woofer socket
(option)
In some models you must connect the woofer connector on the
back to the WOOFER socket on the back of the set to hear the
woofer sound.
1.
Connect the woofer connector
socket
OUT
ANT IN
75Ω
on
the back to the WOOFER
N(AV2)
VDEO
L
AUDIO
R
WOOFER
2.
Adjust
section.
24
on
the back of the set.
the woofer sound. Refer to the 'Sound
adjustment'
Troubleshooting
check list
Contents
Symptoms
No
picture,
no
Sound
sound
OK, poor picture
Picture
OK, poor sound
Picture blurred
Lines
or
streaks in
Poor
picture
reception
on some
channels
No colour
Poor colour
Remote control does not work
Check these items and try to
adjust these
The mains plug-(plugged in and
switched on)
Is the TV switched
Try
on
another channel
(weak signal)
Check aerial
(plugged
into
Check aerial
(broken lead?)
TV?)
Check aerial
Check for local interference
Adjust
contrast
Adjust brightness
Adjust
colour
Adjust
volume
Check the batteries in remote control
Check Audio/Video sockets
(VCR only)
25
Download PDF