LG | CT-29Q10E | LG CT-29Q10ET Owner’s Manual

Colour Television
OWNER'S MANUAL
Please read this manual
carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
the back cover and quote this
information to your dealer when you require service.
Model number
:
Serial number
:
on
Contents
Installation
3
Location and function of controls
4
Remote control handset
Battery installation
Front panel
Basic
operation
Programme selection
Volume adjustment / Mute function
On screen language selection
7
On and off /
On
/ Quick view
8
screen menus
Menu selection
up TV stations
Auto programme tuning
Manual programme tuning
9
Setting
Fine
Tuning
Programme edit
Calling the programme
Picture
adjustment
adjustment
Picture
table
14
/
Eye (option)
/ Picture format
Sound
15
adjustment
adjustment
Stereo / Dual reception
NICAM reception
Sound
Sound output selection
Other functions
17
TV and AV modes / Auto AV
switching
Child lock / Auto sleep / AVL (Auto volume leveler)
VM (Velocity Modulation) / Tilt (option)
Sleep timer
Teletext
19
(option)
Switch
on
/ off
SIMPLE text
TOP text
(option)
FASTEXT mode
Special
teletext functions
Connection of external
22
equipment
Aerial socket
Euro scart sockets
Audio / Video in sockets
S-video / Audio in sockets
Headphone
Troubleshooting
2
(S-AV)
socket
check list
Back
cover
Installation
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set.
In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs.
Warning
To prevent fire
moisture.
or
shock hazard, do not expose the set to rain
or
Service
Never
the back cover of the set as this can expose you to
very high voltage and other hazards. If the set does not operate
properly, unplug it and call your dealer.
remove
Aerial
Connect the aerial cable to the socket marked +75 Ω on the back
cover. For the best reception an outdoor aerial should be used.
Location
Position your set so that no bright light or sunlight falls directly onto
the screen. Care should be taken not to expose the set to any
unnecessary vibration, moisture, dust or heat. Also ensure that the
set is placed in a position to allow a free flow of air. Do not cover
the ventilation openings on the back cover.
3
Location and function of controls
All the functions
can
be controlled with the remote control handset.
Some functions
can
also be
panel
adjusted
with the buttons
on
the front
of the set.
Remote control handset
Before you use the remote control handset,
teries. See the next page.
please
install the bat-
1
1.
2
1
23
TV/AV
4
56
ARC
POWER
(r)
switches the set
2.
3
on
89
4
on or
SSM/
DASS
VOL
OK
TEXT MENU
off to
or
directly
standby.
off.
NUMBER BUTTONS
switches the set
on
from
standby
PR
5
6
or
PSM
3.
0
standby
MUTE(W)
switches the sound
7
from
VOL
4.
DUAL
select
PR
(I/II/*)
PR.LIST
5.
DASS
(Digital
Audio Surround
System)
selects DASS sounds.
6.
7
8
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
Q.VIEW
SP/LP
CH
REW
PLAY
FF
CH
P/STILL
STOP
REC
MENU
selects
a menu.
T
X
T
M
EYE
7.
ON/OFF
TELETEXT BUTTONS
These buttons
9
are
For further details,
8.
9.
(option)
used for teletext.
see
the 'Teletext' section.
Q. VIEW
returns to the
EYE
previously
viewed programme.
(option)
switches the eye function
4
number.
selects the language during dual language broadcast.
selects mono sound during stereo broadcast.
SLEEP
SIZE
a
on or
off.
Location and function of controls
10. TV/AV
selects TV or AV mode.
clears the menu from the screen.
switches the set on from standby.
11. ARC
(Aspect Ratio Control)
changes the picture format.
12. PSM
(Picture Status Memory)
preferred picture setting.
recalls your
13. SSM/* (Sound Status Memory)
recalls your preferred sound setting.
14.
menu
4
56
ARC
89
PSM
3
TV/AV
11
7
12
0
SSM/
13
PR
settings.
DASS
OK
accepts your selection
2
10
Δ / Ε (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
Φ / Γ
(Volume Up/Down)
adjusts the volume.
adjusts
1
or
displays
VOL
the current mode.
OK
TEXT MENU
VOL
SLEEP
PR
15. SLEEP
sets the
sleep
14
15
PR.LIST
timer.
16
16. PR. LIST
displays the programme table.
17. VCR BUTTONS
control
a
LG video cassette recorder.
Note : The PR. LIST button is used
text mode.
as
T
X
T
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
Q.VIEW
SP/LP
CH
REW
PLAY
FF
CH
P/STILL
STOP
REC
M
teletext colour button in teleEYE
ON/OFF
17
Battery
installation
The remote control handset is powered by two AA type batteries.
Gently pull down the cover of the remote control handset until the
battery compartment is exposed. Install two batteries as indicated
by the polarity symbols ( §] and §^) marked inside the compartment.
Note : To avoid damage from possible battery leakage, remove the
batteries if you do not plan to use the remote control handset for an
extended period of time.
5
Location and function of controls
Front
panel
8
MENU
POWER
S-VIDEOL/MN
7
OK
VOL
PR
1234
AUDIO
6
5
STAND BY
POWER
R
MENU
OK
VOL
PR
AV3
3
1
26
4
5
8
S-VIDEOL/MN
7
POWER
MENU
AUDIO
1
3
OK
VOL
4
PR
26
5
R
AV3
Side
panel
1.
MAIN POWER (POWER
switches the set on or off.
2.
POWER/STANDBY INDICATOR
illuminates brightly when the set is in
mode.
dims when the set is switched on.
3.
4.
MENU
selects
)
7.
AUDIO/VIDEO IN SOCKETS (AV3)
Connect the audio/video out sockets of external equipment to these sockets.
standby
S-VIDEO/AUDIO IN SOCKETS (S-AV)
Connect the video out socket of an S-VIDEO
VCR to the S-VIDEO socket.
Connect the audio out sockets of the SVIDEO VCR to the audio sockets as in AV3.
OK
or
mode.
displays
the current
Φ / Γ
(Volume Up/Down)
adjusts the volume.
adjusts menu settings.
Δ / Ε (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
EYE
(option)
adjusts picture according
conditions.
6
REMOTE CONTROL SENSOR
a menu.
accepts your selection
5.
6.
to the
surrounding
8.
HEADPHONE SOCKET
Connect the headphone
plug
to this socket.
Basic
operation
On and off
1.
2.
Press the main power button to switch the set on.
If the set is in standby mode, press the r(power), Δ / Ε, TV/AV
or NUMBER buttons on the remote control handset to switch it
on
3.
4.
fully.
Press the r(power) button on the remote control handset.
The set reverts to standby mode.
Press the main power button again to switch the set off.
Note : If, while the set is switched on, the mains plug is disconnected the set will switch to standby or power on when the mains
plug is replaced in the mains power socket.
Programme
selection
You can select
buttons.
a
programme number with the
Δ
/
Ε
1
2
4
56
ARC
89
PSM
3
NUMBER
or
7
0
Volume
adjustment
Press the
Φ
TV/AV
SSM/
PR
DASS
/
Γ
button to
adjust
the volume.
VOL
OK
TEXT MENU
VOL
SLEEP
PR
Mute function
PR.LIST
Press the W button. The sound is switched off and the
appears.
You can cancel it
button.
by pressing
theW,
Φ
display W
/ Γ, SSM/*, I/II/*
DASS
or
UPDATE
INDEX
REVEAL
MODE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
SIZE
T
X
T
Quick view
MIX
M
EYE
Press the Q.VIEW button to view the last programme you
were
watching.
On
screen
language
selection
The menu can be displayed
First select your language.
1.
2.
3.
4.
5.
6.
HOLD
on
the
screen
in desired
language.
the MENU button to select the Station menu.
the Δ / Ε button to select Language.
the OK button.
the Δ / Ε or Φ / Γ button to select your desired language.
Press the OK button.
All the on screen displays will appear in the selected language.
Press the TV/AV button to return to normal TV viewing.
Press
Press
Press
Press
7
On
screen menus
The
an
dialogue
operator
also
between you and your set takes place on screen with
The buttons required for the operating steps are
menu.
displayed.
Menu selection
1.
the MENU button to display each menu.
Press the Δ / Ε button to select a menu item.
The selected menu item changes from green to purple.
3. Press the Φ / Γ button to change the setting of a menu item or
OK button to display the sub menu.
Note :
In the AV mode, the Station menu is not displayed.
a.
b. In the teletext mode, menus are not displayed.
In SECAM-L models, the Normal/Turbo search will not disc.
play, only the Start will display in the Auto programme menu.
d. In some models, the Super woofer will display in the Sound
menu. Only a set with Airo-dome speaker can perform this function.
Repeatedly press
2.
ARC
PSM
PR
DASS
VOL
OK
TEXT MENU
VOL
SLEEP
PR
PR.LIST
AutoOprogramme
System
StorageOfrom
ProgrammeOedit
NormalOsearch
Language
TurboOsearch
()OOKOMENUOTV
AV
Station
T
X
T
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
M
EYE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
()O}{OOMENUOTV
80
' OContrast
Channel
・OColourOOOOOO50
Search
≥OSharpnessOOO50
AV
Picture
0
Off
20
§Volume
()O}{OOKOMENUOTV
AV
Sound
I nput
ChildOlock
AutoOsleep
AVL
VM
BG
V
UHF020
{{{
NameOOOOOOOOOC020
1
Storage
()O}{OOKOMENUOTV
AV
menu
Flat
OBalance
ODASS
AV
System
Fine
()O}{OOKOMENUOTV
1
menu
ΩOBrightnessOO50
OEqualizer
0
ARD
5ARD1
1FTZ
6FDZ1
2C127C12
3S48S44
4 CH_5
9 CH_5
}{O?DeleteO?Copy
()O?MoveOOO?Skip
menu
TV
Off
Off
Off
Off
FlatOOOO+10
Music
MovieOOO_0
Speech
Tilt
00
UserOOOO_10
OOOOOOOO0.1O0.5O1.5O5.0O10OkHz
()O}{OOKOMENUOTV
AV
()OMENUOTV
Special
TV programme
8
BG
ManualOprogramme
menu
AV
Setting up
TV stations
Up to 100 TV stations can be stored in this set by programme numbers
(0 to 99). Once you have preset the stations, you will be able to use
the Δ / Ε or NUMBER buttons to scan the stations you programmed.
Stations can be tuned using automatic or manual modes.
Auto programme
AutoOprogramme
ManualOprogramme
tuning
ProgrammeOedit
Language
All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this
set.
1.
2.
3.
Station
Menu
()OOKOMENUOTV
AV
the MENU button to select the Station menu.
Press the Δ / Ε button to select Auto programme.
Press the OK button to display the Auto programme menu.
Repeatedly press
1
2
4
56
ARC
89
PSM
3
BG
System
1
StorageOfrom
TV/AV
NormalOsearch
TurboOsearch
7
()O}{OOMENUOTV
AV
0
4.
Press the
Δ
/
Ε
button to select
System. Select
a
TV
withtheΦ/Γbutton;
L
:
SECAM L/L' (France : SECAM-L models only)
BG : PAL B/G, SECAM B/G (Europe/East Europe)
5.
6.
7.
system
VOL
I
:
PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
Press the Δ / Ε button to select Storage from.
Select the beginning programme number with the Φ / Γ button
or NUMBER buttons. Any number under 10 is entered with a
numeric '0' in front of it, i.e. '05' for 5.
Press the Δ / Ε button to select Normal or Turbo search.
Option:
In SECAM-L models,
Only
can
BG
8.
S ystem
VOL
SLEEP
PR
PR.LIST
T
X
T
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
M
EYE
BG
1
StorageOfrom
1
NormalOsearchOCO15
StorageOfrom
TurboOsearch
2OOOOOOOOOOOOOO2%
TurboOsearchO CO38
2OOOOOOOOOOOOOO2%
MENU
MENU
(Normal search)
OK
TEXT MENU
select Start.
Note :
a.
Turbo search is further faster than Normal search and in some
models, these searches will automatically store all receivable stations.
b. If the programmed station has poor quality sound, select the system
again in the Manual programme menu.
S ystem
PR
DASS
NormalOsearch
(Turbo search)
Press the OK button to begin auto programming.
All receivable stations are stored. The station name is stored for
stations which broadcast VPS (Video Programme Service),
PDC (Programme Delivery Control) or TELETEXT data. If no
station name can be assigned to a station, the channel number
is assigned and stored as C (V/UHF 01-69) or S (Cable 01-47),
followed by a number.
To stop auto
programming, press
the MENU button.
When auto programming is completed, the Programme edit
menu appears on the screen. See the 'Programme edit' section
to edit the stored programme.
9.
Press the TV/AV button to return to normal TV
viewing.
9
Setting up
Station
Menu
TV stations
Manual programme
AutoOprogramme
ManualOprogramme
ProgrammeOedit
tuning
Manual programme lets you manually tune and arrange the stations
in whatever order you desire. Also you can assign a station name with
five characters to each programme number.
Language
()OOKOMENUOTV
AV
1.
2.
3.
the MENU button to select the Station menu.
Press the Δ / Ε button to select Manual programme.
Press the OK button to display the Manual programme menu.
Repeatedly press
BG
System
Channel
V
UHF020
Fine
1
2
3
{{{
Search
NameOOOOOOOOOC020
1
Storage
56
ARC
789
PSM
4
()O}{OOKOMENUOTV
4.
PR
DASS
OK
TEXT MENU
VOL
SLEEP
5.
PR
PR.LIST
6.
7.
T
X
T
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
M
EYE
Δ
/
Ε
button to select
System. Select
a
TV
system
withtheΦ/Γbutton;
0
VOL
Press the
AV
8.
L
: SECAM L/L' (France : SECAM-L models only)
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I
:
PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
Press the Δ / Ε button to select Channel. Press the Φ / Γ button to select V/UHF or Cable as required.
If possible, select the channel number (1 to 69) directly with the
number buttons. Any number under 10 is entered with a numeric
'0' in front of it, i.e. '05' for 5.
Press the Δ / Ε button to select Search. Press the Φ / Γ button
to commence searching. If a station is found the search will stop.
If this station is the one required, press the Δ / Ε button to select
Storage. Select the desired programme number (0 to 99) with
the Φ / Γ button or NUMBER buttons. Any number under 10 is
entered with a numeric '0' in front of it, i.e. '05' for 5.
Press the OK button to store it. The display Stored will appear.
S ystem
Channel
Fine
BG
V
UHF020
{{{
Search
NameOOOOOOOOOC020
1
Storage
Stored
9.
To store another station, repeat steps 4 to 8.
Assigning a station name
1. Repeat the 'Manual programme tuning' steps
2.
3.
4.
5.
10
1 to 3.
Press the Δ / Ε button to select Name.
Press the Γ button. You can use a blank, +, -, the numeric 0 to 9
and the alphabet A to Z.
With the Φ button you can select in the opposite direction.
Select the next position by pressing the OK button and then take
your choice of the second character, and so on.
Repeat the 'Manual programme tuning' steps 7 to 8.
TV stations
Setting up
Fine
Station
Menu
tuning
Normally
fine
tuning
is
only necessary
if
reception
is poor.
AutoOprogramme
ManualOprogramme
ProgrammeOedit
1.
2.
3.
Language
the 'Manual programme tuning' steps 1 to 3.
Press the Δ / Ε button to select Fine.
Repeat
Press the
Φ
/
Γ
button to fine tune for the best
()OOKOMENUOTV
picture
AV
and
sound.
4.
5.
the 'Manual programme tuning' steps 7 to 8.
Press the TV/AV button to return to normal TV viewing.
Repeat
finely tuned programme will
during programme selection.
The
be indicated
by yellow
number
TV/AV
ARC
PSM
PR
DASS
VOL
OK
TEXT MENU
VOL
SLEEP
PR
PR.LIST
T
X
T
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
M
EYE
11
Setting up
Station
Menu
Programme
A utoOprogramme
ManualOprogramme
ProgrammeOedit
Language
()OOKOMENUOTV
AV
1
2
4
56
ARC
789
PSM
3
1.
2.
3.
}{O?DeleteO?Copy
()O?MoveOOO?Skip
Deleting
PR
DASS
VOL
OK
the MENU button to select the Station menu.
Press the Δ / Ε button to select Programme edit.
Press the OK button to display the Programme edit menu.
Repeatedly press
0ARD
5ARD1
1FTZ
6FDZ1
2C127C12
3S48S44
4 CH_5
9 CH_5
1.
2.
TEXT MENU
edit
This function enables you to delete or skip the stored programmes.
Also you can move some stations to other programme numbers or
insert a blank station data into the selected programme number.
TV/AV
0
TV stations
a programme
Select a programme to be deleted with the Δ / Ε or Φ / Γ button.
Press the RED button twice.
The selected programme is deleted, all the following programmes are shifted up one position.
VOL
SLEEP
PR
Copying
1.
2.
PR.LIST
a programme
Select a programme to be copied with the Δ / Ε
Press the GREEN button.
All the following programmes are shifted down
or Φ
one
/
Γ
button.
position.
Moving
T
X
T
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
1.
2.
3.
4.
a programme
Select a programme to be moved with the Δ / Ε or Φ / Γ button.
Press the YELLOW button.
Move the programme to the desired programme number with
the Δ / Ε button.
Press the YELLOW button again to release this function.
M
EYE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
0ARD
5ARD1
1FTZ
6FDZ1
2C127C12
3S48S44
4 CH_5
9 CH_5
()O
? MoveO Off
a programme number
Select a programme number to be skipped with the Δ / Ε or Φ / Γ
button.
Press the BLUE button. The skipped programme turns to blue.
Press the BLUE button again to release the skipped pro-
Skipping
1.
2.
3.
gramme.
When a programme number is skipped it means that you will be
unable to select it using the Δ / Ε button during normal TV
viewing. If you want to select the skipped programme, directly
enter the programme number with the NUMBER buttons or
select it in the programme edit or table menu.
Note
:
The programme number 01 cannot be
skipped.
Press the TV/AV button to return to normal TV
12
viewing.
Setting up
TV stations
the programme table
Calling
can check the programmes stored in the memory
the programme table.
You
Displaying programme
1.
by displaying
table
Press the PR. LIST button to
display
the
Programme
table
menu.
The programme table appears on the screen. One programme
table contains ten programmes as below.
TV/AV
0ARD
5ARD1
1FTZ
6FDZ1
2C127C12
3S48S44
4 CH_5
9 CH_5
()O}{OOKOMENUOTV
Note
a.
PSM
AV
:
You may find
auto
b.
ARC
some
programming
blue programmes. They are skipped
or in the programme edit mode.
PR
during
Some programmes with the channel number shown in the programme table indicate there is no station name assigned.
DASS
VOL
OK
TEXT
VOL
SLEEP
PR
PR.LIST
programme in the programme table
Select a programme with the Δ / Ε or Φ / Γ button.
Then press the OK button.
Selecting
a
The set switches to the chosen programme number.
a programme table
10 programme table pages in which contain 100 pro-
Paging through
There
are
T
X
T
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
M
EYE
grammes.
Pressing the
Δ
/
Ε
or Φ
/
Γ
button
repeatedly
Press the TV/AV button to return to normal TV
turns the pages.
viewing.
13
Picture
Picture
Menu
Picture
You
adjustment
adjustment
adjust picture contrast, brightness, colour intensity, sharptint (NTSC AV only) to the levels you prefer.
Repeatedly press the MENU button to select the Picture menu.
Press the Δ / Ε button to select the desired picture item.
Press the Φ / Γ button to make appropriate adjustments.
can
ness and
80
'OContrast
ΩOBrightnessOO50
・OColourOOOOOO50
≥OSharpnessOOO50
()O}{OOKOMENUOTV
1.
2.
3.
AV
'OContrastOOOO80
ΩOBrightnessOO50
・OColourOOOOOO50
≥OSharpnessOOO50
TV/AV
ARC
PSM
4. Press the OK button to store it for the picture User.
To recall your preferred setting, press the PSM button until the
desired picture (Standard, User, Dynamic or Mild) appears.
The picture Standard, Dynamic and Mild are programmed for
good picture reproduction at the factory and cannot be changed.
Eye (option)
PR
DASS
VOL
OK
TEXT MENU
VOL
SLEEP
PR
T
X
T
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
M
EYE
EYE
Eye is an optional function. Only a set with eye option can perform
this function.
In some models, the set will automatically adjust the picture according to the surrounding conditions. This will enable you to enjoy the
most suitable picture according to the surroundings.
Press the EYE/* button to switch the eye function
on or
off.
Off
When the eye function is on, the most suitable picture automatically is adjusted according to the surrounding conditions.
in green does not appear continuAt this time the display
in yellow appears each time the picously but the display
ture condition changes.
Note : If you press the PSM button with the eye function, the eye
function is automatically switched off.
Picture format
You can watch the TV in various picture formats; Standard, Wide or
Zoom.
Repeatedly press the ARC button to select your desired picture format.
Standard
This picture format is 4 to 3 of
general
TV.
Wide
You can enjoy the cinema (the picture format of 16:9) or general TV
programme through the 16:9 mode.
The screen 16:9 is viewed just like that but the screen 4:3 is magnified to the left and right so that the screen 16:9 is full.
Zoom
You can enjoy the cinema in a vast screen through the Zoom mode.
The screen 4:3 is magnified to the upper/lower and left/right sides
so that the screen 16:9 is full. The bottom and top of the picture
may be lost.
Note :
a.
When you switch the set to standby or off, the Wide or Zoom
picture format is reset to the Standard (4:3).
b. In the manual AV mode, Wide picture format is not available.
14
Sound
Sound
adjustment
Sound
Menu
adjustment
You
can select your preferred sound setting; Flat, Music, Movie or
Speech as you prefer. Also you can adjust the sound frequence of
equalizer, balance, DASS (Digital Audio Sound System) on/off,
headphone volume/sound or super woofer on/off (option). The
DASS creates
optional
all around sound
an
woofer sound stresses and
1.
Repeatedly press
2.
Press the
in
a
Flat
0
OBalance
ODASS
Off
20
§Volume
()O}{OOKOMENUOTV
AV
concert hall and the
emphasized
bass.
the MENU button to select the Sound
menu.
button to select the desired sound item;
Equalizer,
Super woofer (option).
Press the Φ / Γ button to make desired adjustment.
Press the OK button in Equalizer to set the Equalizer User.
Δ
/
Ε
Balance, DASS, §Volume
3.
as
OEqualizer
or
TV/AV
ARC
PSM
FlatOOOO+10
SSM/
Music
MovieOOO_0
PR
Speech
DASS
UserOOOO_10
OOOOOOOO0.1O0.5O1.5O5.0O10OkHzO
()O}{OOKOMENUOTV
VOL
AV
OK
TEXT MENU
VOL
SLEEP
PR
a.
b.
c.
Select User
by pressing the Δ / Ε button.
Select a sound band by pressing the Φ / Γ button.
Make appropriate sound level with the Δ / Ε button.
PR.LIST
d. Press the OK button to store it for the sound User.
The
display
Stored appears and
Equalizer
menu
will
disap-
pear.
To recall your preferred setting, press the SSM/* button until the
desired sound (User, Flat, Music, Movie or Speech) appears.
The sound Flat, Music, Movie and Speech are programmed for
good sound reproduction at the factory and cannot be changed.
Alternatively you
can
select the DASS On
or
Off
by pressing
T
X
T
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
M
EYE
the
DASS button.
: If you press the SSM/* button after making appropriate
adjustment in Sound menu, the display User automatically appears
even though you have already set a factory preset setting; Flat,
Music, Movie or Speech.
Note
15
Sound
adjustment
Stereo/Dual
reception
When a programme is selected, the sound information for the station appears after the programme number and station name disap-
pear.
Broadcast
On Screen
Mono
MONO
Stereo
STEREO
Dual
DUAL I
Display
Mono sound selection
In stereo reception if the stereo signal is weak, you can switch to
mono by pressing the I/II/* button twice. In mono reception the
depth of sound is improved. To switch back to stereo, press the
I/II/* button twice again.
selection for dual language broadcast
If a programme received in two languages (dual language), you can
switch to DUAL I, DUAL II or DUAL I II by pressing the I/II/* button repeatedly.
DUAL I sends the primary broadcast language to the loudspeakers.
DUAL II sends the secondary broadcast language to the loud-
Language
speakers.
DUAL I II sends
NICAM
a
separate language
to each
loudspeaker.
reception
If your set is equipped with the receiver for NICAM reception, the
high quality NICAM (Near Instantaneous Companding Audio
Multiplex) digital sound can be received.
Sound output can be selected according to the type of received
broadcast as follows by pressing the I/II/* button repeatedly.
1.
2.
3.
When NICAM mono is received, you can select NICAM
MONO or FM MONO.
When NICAM stereo is received, you can select NICAM
STEREO or FM MONO. If the stereo signal is weak, switch to
FM mono.
When NICAM dual is received, you can select NICAM DUAL I,
NICAM DUAL II or NICAM DUAL I II or MONO. When FM
mono is selected the display MONO appears on the screen.
Sound output selection
In AV mode, you
can
select output sound for the left and
right
loud-
speakers.
Repeatedly press the I/II/* button to select the sound output.
:
Audio signal from audio L input is sent to left loud-speaker
and audio signal from audio R input is sent to right loudspeaker.
L+L :
Audio signal from audio L input is sent to left and right loudspeakers.
R+R :
Audio signal from audio R input is sent to left and right loudspeakers.
L+R
16
Other functions
Special
TV and AV modes
Menu
be set for TV or AV mode. AV mode is used when a video
cassette recorder (VCR), or other equipment is connected to the
Inputs
can
TV
Off
Off
Off
Off
Input
ChildOlock
set.
AutoOsleep
Note : When a VCR is connected via the aerial socket the set is used
in TV mode. See the 'Connection of external equipment' section.
()O}{OMENUOTV
1.
2.
3.
AVL
VM
the MENU button to select the
button to select Input.
Repeatedly press
Press the
Δ
/
Ε
Special
Tilt
00
AV
menu.
PresstheΦ/ΓbuttontoselectTV,AV1,AV2orAV3.
The three AV modes are :
AV1 : VCR connected to the Euro scart socket 1 on the back
AV2 : VCR connected to the Euro scart socket 2 on the back
AV3 : VCR connected to the AV3 sockets on the side panel
To return to TV mode, press the
Alternatively you
can
Δ
/
select the TV
TV/AV button.
Ε or
or
NUMBER buttons.
AV mode
by pressing
the
1
2
4
56
ARC
89
PSM
7
3
TV/AV
0
Auto AV
PR
switching
If your VCR outputs switching voltage when it is switched to playback with the VCR connected to the Euro scart socket 1 or 2. The
set is automatically switched to AV 1 or AV 2 mode when an AV signal is input. But if you want to keep on watching TV mode, press the
Δ / Ε or NUMBER buttons.
Press the TV/AV button to return to AV modes.
VOL
OK
TEXT MENU
VOL
SLEEP
PR
PR.LIST
Child lock
The TV can be set so that the remote control handset is needed to
control it. This feature can be used to prevent unauthorized view-
ing.
T
X
T
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
M
EYE
1.
2.
3.
4.
the MENU button to select the Special menu.
Press the Δ / Ε button to select Child lock.
Press the Φ / Γ button on the remote control handset to select
On.
Press the TV/AV button to return to normal TV viewing.
Repeatedly press
With the lock on, the display Child lock On appears on the screen
if any button on the front panel is pressed while viewing the TV.
Note : The display Child lock On will not appears on the screen if
any button on the front panel is pressed while displaying the menus.
Auto
sleep
If you select Auto sleep On the set will automatically switch itself
to standby mode approximately ten minutes after a TV station stops
broadcasting.
1.
2.
3.
4.
the MENU button to select the Special
Press the Δ / Ε button to select Auto sleep.
Press the Φ / Γ button to select On.
Press the TV/AV button to return to normal TV viewing.
Repeatedly press
menu.
17
Other functions
Special
AVL
Menu
TV
Off
Off
Off
Off
Input
ChildOlock
AutoOsleep
AVL
VM
Tilt
00
()O}{OMENUOTV
AV
If you select AVL On, the set automatically
level even if you change programmes.
keeps
on an
equal
vol-
ume
1.
2.
3.
4.
VM
TV/AV
(Auto volume leveler)
the MENU button to select the Special
Press the Δ / Ε button to select AVL.
Press the Φ / Γ button to select On.
Press the TV/AV button to return to normal TV viewing.
Repeatedly press
menu.
(Velocity Modulation)
If you select VM On, set will
of image edge.
automatically
enhance the
sharpness
ARC
PSM
1.
2.
3.
4.
the MENU button to select the Special
Press the Δ /Ε button to select VM.
Press the Φ /Γ button to select On or Off.
Press the TV/AV button to return to normal TV viewing.
Repeatedly press
menu.
PR
DASS
VOL
VOL
TEXT MENU
SLEEP
PR
Tilt
(option)
The TV
another
picture may tilt to the
position. This function
left
can
or right if the TV set moves to
be used to compensate the tilt.
PR.LIST
1.
2.
3.
4.
T
X
T
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
the MENU button to select the Special
Press the Δ /Ε button to select Tilt.
Press the Φ /Γ button to adjust the tilt.
Press the TV/AV button to return to normal TV viewing.
Repeatedly press
Sleep
menu.
timer
M
EYE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
You don't have to remember to switch the set off before you go to
sleep. The sleep timer automatically switches the set to standby
after the preset time elapses.
Press the SLEEP button to select the number of minutes. The diswill appear on the screen, followed by 10, 20, 30, 60, 90,
play r
120, 180 and 240. The timer begins to count down from the number
of minutes selected.
---
Note :
a.
To view the
remaining sleep time, press
the SLEEP button
once.
b.
To cancel the sleep time, repeatedly press the SLEEP button
until the display r
appears.
When you switch the set off, the set releases the preset sleep
time.
---
c.
18
Teletext
(option)
Teletext (or TOP text) is an optional function, therefore only
with the teletext system can receive the teletext broadcast.
a
set
free service broadcast by most TV stations which gives
information on news, weather, television programmes, share prices and many other topics.
Teletext is
a
up-to-the-minute
The teletext decoder of this TV can support the SIMPLE, TOP and
FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern
methods allowing quick and easy selection of teletext information.
Switch on/off
1
2
Press the TEXT button to switch to teletext. The initial page or last
selected page appears on the screen.
Two page numbers, TV station name, date and time are displayed
on the screen headline. The first page number indicates your selection, while the second shows the current page displayed.
Press the TEXT or TV/AV button to switch off teletext. The previous
mode reappears.
4
56
ARC
89
PSM
7
3
TV/AV
0
PR
DASS
OK
TEXT
SIMPLE text
SLEEP
PR
PR.LIST
selection
Enter the desired page number as a three digit number with the
NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then reenter the correct page number.
The Δ / Ε button can be used to select the preceding or fol-
Page
1.
2.
lowing page.
Programming
a
T
X
T
colour button in LIST mode
SIZE
HOLD
UPDATE
INDEX
MIX
TIME
REVEAL
MODE
Q.VIEW
SP/LP
ON/OFF
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
M
EYE
If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the
MODE button to switch to LIST mode.
Four teletext page numbers of your choice can be colour coded and
easily selected by pressing the corresponding coloured button on
the remote control handset.
1.
Using
2.
gramme.
Wait until the page is displayed on the screen and press the OK
button. The page numbers in the colour boxes along the bottom
the NUMBER buttons, select the page you wish to pro-
to "000?".
of the
screen
3.
Press
a
4.
you can
The three other coloured buttons
change
colour button to store the page number. From now on,
select this page with the same coloured button.
are
programmed
in the way.
19
Teletext
TOP text
(option)
(option)
The user guide displays four fields-red, green, yellow and blue at
the bottom of the screen. The yellow field denotes the next group
and the blue field indicates the next block.
1
2
4
56
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the yellow button to proceed to the next group with automatic overflow to the next block.
3. With the green button you can proceed to the next existing
page with automatic overflow to the next group.
Alternatively the Δ button can be used.
4. The red button permits to return to previous selection.
Alternatively the Ε button can be used.
3
789
ARC
PSM
Direct page selection
Corresponding to the SIMPLE teletext mode, you can select a page
by entering it as a three digit number using the NUMBER buttons in
TOP mode.
0
PR
DASS
FASTEXT
SLEEP
PR
The teletext pages are colour coded along the bottom of the screen
and are selected by pressing the corresponding coloured button.
PR.LIST
selection
Press the INDEX button to select the index page.
You can select the pages which are colour coded along the bottom line with the same coloured buttons.
Corresponding to the SIMPLE teletext mode, you can select a
page by entering its three digit page number with the NUMBER
buttons in FASTEXT mode.
The Δ / Ε button can be used to select the preceding or fol-
Page
1.
2.
TX
INDEX
SIZE
HOLD
UPDATE
MIX
TIME
REVEAL
Q.VIEW
SP/LP
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
T
4.
EYE
20
3.
ON/OFF
lowing page.
Teletext
(option)
teletext functions
Special
REVEAL
Press this button to
tions of riddles
or
Press this button
display concealed information, such as solupuzzles.
again to remove the information from the display.
SIZE
Selects double
height text.
enlarge the top half of the page.
button again to enlarge the bottom half of the page.
button again to return to the normal display.
Press this button to
Press this
Press this
1
2
4
56
ARC
89
PSM
3
UPDATE
the TV
Displays
text page. The
picture
display
of the
When the
screen.
will
on
the
screen
while
waiting
for the
new
7
tele-
will appear at the top left hand corner
updated page is available then display
0
PR
to the page number.
Press this button to view the updated teletext page.
change
DASS
SLEEP
HOLD
Stops
PR
the automatic page change which will occur if a teletext page
or more sub pages. The number of sub pages and the
consists of 2
sub page displayed is, usually, shown on the screen below the time.
When this button is pressed the stop symbol is displayed at the top
left-hand
of the
corner
screen
and the automatic page
change
is
inhibited.
To continue press this button
T
X
T
again.
SIZE
HOLD
UPDATE
MIX
TIME
REVEAL
Q.VIEW
SP/LP
CH+
REW
PLAY
FF
CH-
P/STILL
STOP
REC
EYE
MIX
Displays
the teletext pages superimposed on the TV
picture off press this button again.
picture.
ON/OFF
To switch the TV
TIME
When
viewing
time at the top
again
TV programme, press this button to display the
right hand corner of the screen. Press this button
a
to remove the
display.
In the teletext mode, press this button
displayed at
to select a sub page number. The sub page number is
the bottom of the
Ε
/
Press
Δ
or
screen.
To hold
or
change
the sub page, press the
NUMBER buttons.
again
to exit this function.
21
Connection of external
You
connect additional
can
equipment
equipment,
such
as
VCRs, camcorders
etc. to your set.
Here shown may be somewhat different from your set.
Aerial socket
ANT IN
L L 75Ω
1.
2
1
2.
3.
VCR
4.
5.
Connect the RF out socket of the VCR to the aerial socket on
the back of the set.
Connect the aerial cable to the RF aerial in socket of the VCR.
Store the VCR channel on a desired programme number using
the 'Manual programme tuning' section.
Select the programme number where the VCR channel is
stored.
Press the PLAY button on the VCR.
Euro scart sockets
1.
ANT IN
L L 75Ω
2.
2
1
VCR
Connect the Euro scart socket of the VCR to the Euro scart
socket 1 or 2 of the set.
Press the PLAY button on the VCR.
If your VCR outputs a switching voltage connect to Euro scart
socket 1 or 2, the set will switch to AV 1 or AV 2 mode automatically. But if you want to keep on watching TV mode, press the
Δ / Ε or NUMBER buttons.
Otherwise press the TV/AV button
on
set to select AV 1 or AV 2. The VCR
on
the
You
the remote control hand-
playback picture appears
screen.
can
also record programmes received
by
the TV
on
video
tape.
Note
a.
b.
:
i.e. the signals red, green and blue can only
be selected for the Euro scart socket 1 (not Euro scart 2).These
signals are transmitted, for example, by a computer, pay TV
decoder, game machine or photo CD unit, etc.
If both Euro scart 1 and 2 sockets have been connected to the
VCRs simultaneously, only the AV 1 can be received.
Signal type RGB,
Audio / Video in sockets
1.
S-VIDEOL/MN
2.
3.
AUDIO
R
AV3
VCR
22
Connect the audio/video out sockets of the VCR to audio/video
in sockets of the set.
Press the TV/AV button to select AV 3.
Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
Note : If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO socket on the side panel.
Connection of external
S-video / Audio in sockets
When
connecting
picture quality will
1.
the side
4.
S-VIDEO VCR to the S-VIDEO socket, the
an
be further
S-VDEOIL/MN
improved.
panel
AUDIO
of the set.
R
AV3
Connect the audio cable from the S-VIDEO VCR to the AUDIO
sockets
3.
(S-AV)
Connect the S-video socket of the VCR to the S-VIDEO socket
on
2.
equipment
on
the side
Select AV 3
panel of
by pressing the
Press the PLAY button
The VCR
Note
:
on
the set.
TV/AV button
S-VIDEO VCR
repeatedly.
the VCR.
playback picture appears
the
on
screen.
If both S-VIDEO and VIDEO sockets have been connected
to the S-VHS
VCR
simultaneously, only
the S-VIDEO
can
be
received.
Headphone
Insert the
socket
headphone plug
to the
headphone
socket
on
the side
panel.
You
can
listen to the sound
To
to select
§Volume then press the
menu.
adjust
the
through the headphone and
headphone volume, press the Δ /
speakers.
See the 'Sound
adjustment'
Φ
/
Γ
the TV's
Ε
button
button in the Sound
section.
S-VIDEOL/MN
AUDIO
R
AV3
If you press theW button,
switched off.
When
a
only
the sound from the TV's
programme is received in dual language, you can select
DUAL I II) for the sound from
language (DUAL I, DUAL II or
the headphone regardless of that
a
speakers
are
from the TV's
speakers.
In the
Sound menu, press the Δ / Ε button to select§Volume then
I/II/* button to select the desired language; I, II or I II.
At this time if the set is in AV mode, the I/II/* button selects output
sound;LR,LLorRR,inturn.
OEqualizer
Flat
0
OBalance
ODASS
§Volume
Off
[00 I]20
()O}{OOKOMENUOTV
AV
23
Troubleshooting
check list
Symptoms
No
picture,
no
sound
Sound OK, poor
picture
Picture OK, poor sound
Picture blurred
Lines
or
streaks in
Poor
picture
reception
on some
channels
No colour
Poor colour
Remote control does not work
Check these items and try to
adjust these
The mains plug-(plugged in and
switched on)
Is the TV switched
Try
on
another channel
(weak signal)
Check aerial
(plugged
Check aerial
(broken lead?)
into
TV?)
Check aerial
Check for local interference
Adjust
contrast
Adjust brightness
Adjust
colour
Adjust
volume
Check the batteries in remote control
Check Audio/Video sockets
(VCR only)
Download PDF

advertising