LG | LSW840B | LG LSW840B Owner’s Manual

Install Manual
Tilt Wall Mounting Bracket
Please read this manual carefully before operating your set and retain it
for future reference.
LSW840B
P/NO: MFL63640591 (1503-REV01)
www.lg.com
COMPONENT
Wall mount anchor
8 units
Wall mount screw
8 units
Install manual
Guide spacer 4 units
Guide spacer screw 4 units
(M8X44 mm)
Set protection cushion
4 units
IMPORTANT SAFETY INSTRUCTIONS
- If you are a professional installer, please read this manual carefully before installing the product.
- If you are a professional installer, please give this manual to the user after installing the product and ensure that the user also
reads the manual carefully and retains it for future reference.
After reading the manual, please keep it handy for future reference.
*
*
*
*
*
*
*
Warning
The product should be installed by a qualified
professional specified by the retail store.
Product installation by non-qualified personnel is very
dangerous and may cause personal injury.
The product should be installed where its weight can be
fully supported.
If the product is installed on a weak surface, the product may
fall, causing injury.
When moving or replacing the product after installation,
contact a qualified installer specified by the retail store.
Installation or movement of the product must be carried out by a
skilled professional. If an unqualified person moves and installs
the product, it may cause safety risks.
Do not hang on this product, protect the product from
severe impacts after the installation.
The product may fall and cause injury.
Be sure not to hang the power cable and signal cable on
the back of TV when installing the wall-mounted TV.
Damaged cables may result in fire, electric shock, or damage
to the product.
2
*
*
*
*
*
-
Caution
To install or adjust the height of the product, four or
more people are needed.
If you try to install or move the product alone, it may fall and
cause injury or the product may become damaged.
When installing the product, first check that the wall is
strong enough. Use the anchors and screws provided.
If you use anchors and screws that are not specified by the
manufacturer, they may not hold the weight of the product,
causing safety issues.
When drilling holes into the wall, make sure you use a
drill and drill bit with the specified diameter. Ensure that
you also follow the instructions regarding the depth of
the holes.
Otherwise, the product may be installed incorrectly and
cause safety issues.
Do not clean the product with a wet towel, and do not
place a heater, or humidifier beneath it.
Moisture, steam or heat permeating into this product may
result in fire, electric shock or product damage.
Keep this product away from sprinklers, sensors, hightension wires and power sources. Do not install it in a
location where vibrations or impacts are likely to occur.
Make sure that the power cord is removed from the
outlet before installing the product.
Otherwise, it may cause an electric shock or fire.
Wear safety gloves when installing the product. Do not
use your bare hands.
Otherwise, it may cause personal injury.
ENGLISH
Follow the instructions in this manual to product
properly.
If you do not follow these instructions, the product may be
installed incorrectly and cause serious injury or the product
may become damaged.
Be sure to use the accessory cable provided. Otherwise,
friction between the product and the wall may cause
damage to the connector.
BEFORE INSTALLATION
*
*
*
*
*
*
*
*
*
*
*
*
Do not use the product for purposes other than mounting a display on the wall.
When installing/using the wall mount, be cautious of product damage and avoid accidents.
Install the wall mount according to the installation manual.
If you have not fully read and understood the installation manual, do not install the product and contact the dealer to have a
specialized installer install the product for you.
Even if you are not a specialized installer, it is advantageous to have experience in mechanical or construction field in completely
understanding this manual and installing the product.
Mount the product only on a concrete wall. LG Electronics Inc. is not liable for any accidents caused by mounting the product on walls
made of any other materials, including wood, plywood, and bricks.
Install the product only on a vertical wall.
The manufacturer is not responsible for issue from installing the product on an angled wall or on the ceiling.
Check that the accessories provided with the product are all included before installing. LG Electronics is not liable for any damage or
loss of accessories after the package has been opened.
Keep the included accessories out of reach of babies or children as it can cause safety issues including suffocation from swallowing
the parts.
Make sure screws are tight against the wall, but do not overtighten.
Applying excessive force to screws may damage to the wall, affect the product performance, or cause the product to become
damaged.
Be careful not to install a TV that exceeds the weight restrictions of the wall mount.
Be careful with the tools used during installation to prevent accidents or damage.
--Tools you will need - Phillips head + driver (manual or motorized) / 8 mm socket wrench / Level / Drill.
You may also need an Ø 4 mm drill bit for steel or an Ø 8 mm drill bit for concrete.
3
INSTALLATION
-
- The picture may differ from the actual product.
- Consult a professional installer prior to mounting the TV using a wall bracket.
1
How to Attach the Brackets for the Product to the TV
--If the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and refer to the technical service
manual.
--Work procedure
1.Check to see if the display has screws installed into
the mounting holes. If so, remove those.
2.Assemble the guide spacer and the guide spacer
Guide spacer
screw in order as shown in the picture.
--Place the TV on a table with the screen facing
Guide spacer screw
down. Make sure that you place it on a flat
surface covered with a soft cloth or cushion to
protect it from scratches.
--Secure the guide spacers to the TV with the
screws.Assemble the guide spacer to the set by
tightening the screw.Tighten the screw until the
set, guide spacer and the screw are fully pressing
against one another.
--Use the + driver (manual or motorized) when
tightening the screw.
2
-
How to attach to masonry walls
Please follow the below direction.
--Check the material of the wall and the thickness of the finishing.
--Use the appropriate anchor for a concrete wall, and install them in a manner. That does not crack the wall.
--Do not mount the device on the walls made from wood stud, plasterboard or medium density fiberboard (MDF). In this case, the
anchor and screws must be inserted into the concrete behind the finish surface. If there is no concrete on the other side, then you
must first install a separate hanger to securely install the anchors and screws.
--When installing the product on wall material not designated, install the product so that each location can withstand the pull out load of
70 kgf (686 N) and shear load of 100 kgf (980 N) or above.
Anchor
a
c
b
Wall mount screw
d
e
--Use the Ø 8 mm drill bit for concrete and hammer (Impact) drill.
a.Use a drill bit Ø 8 mm to drill a hole for the anchor location within a depth of 80 mm - 100 mm.
b.Clean the drilled hole.
c.Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.)
d.Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to face upward.
e.Align the wall mount bolt to the hole and tighten it. Then, fasten the bolts at torque of 45 kgf/cm - 60 kgf/cm.
4
3
How to install the wall mount
-M
ount the product only on a concrete wall. LG Electronics Inc. is not liable for any accidents caused by mounting
the product on walls made of any other materials, including wood, plywood, and bricks.
e
Wall mount
screw
4
How to assemble the wall mount support and display
- Always install the display with 2 or more people.
When inserting the guide spacer,
align its center with the arrow
shown in the figure for easy
installation.
* Caution: Prevent the power cord from being pinched between the
wall mounting bracket and the set when installing the set.
(A pinched power cord may cause damage to the product.)
→→ After attaching the guide spacers to the set, hang it on the wall mounting bracket in the direction of the arrows. Attach the lower
part first, then attach the upper part by slightly lifting up the set.
--Make sure that the product is attached securely by pulling on the bottom of the set.
--When mounting the product that has a speaker, hold and lift up the product, not the speaker.
5
ENGLISH
→→ If the screw cannot be assembled in the designated
location inevitably, it can be assembled by
rearranging to the closest location. But, do not
change 2 or more locations from the designated spot.
→→ Attach the right and left side with two bolts each.
→→ At this time, use a + driver (manual or motorized) or
8 mm wrench to tighten the screw so that the wall, wall
bracket and screw are completely pressed against one
another.
5
Setting the Lock Springs
-
-
Lock Spring
After securing the set to the bracket, pull down the lock
springs at the bottom of the wall mounting bracket.
* Caution - If the wall mounting bracket is not attached
securely, the set may fall off, resulting in
damage or injury.
6
Horizontal Level Adjustment
--If the product leans to one side, adjust the tilt with bolt.
(The product tilt is changed according to bolt’s rotation direction.)
-
± 10 mm (Leveling)
6
7
Tilt Angle Adjustment
--To watch the TV after adjusting the angle, please refer the following images and explanations.
(The tilt angle can be adjusted by non-specialized installers. In this case, two or more people are needed)
--When you adjust the angle, hold the product carefully with both hands to avoid any damage to the product or wall.
ENGLISH
❶
15± 2
❸
❹
❷
❷ Bottom Tilt
❶ Top Tilt
❸ Left Tilt
❹ Right Tilt
<Set Side>
<Set rear>
--Some models may not tilt as much as show above.
--Use both hands when adjusting the angles. Do not place the hands on the TV’s back side or the wall mount while adjusting. It could
cause injury.
--When adjusting the ❶❷❸❹ angle, use both hands and adjust the set slowly.
7
8
How to Organize Cables and Attach Protective Cushions
--Organize the cables as shown in the illustration. Please purchase a band for cable organization, or use the band that comes with the
TV.
--Attach the protective cushions to minimize the impact between the wall and the TV in case they bump against each other when
adjusting the angle. Attach them in the desired positions, as illustrated.
Prevent the power cord and the cables from being pinched between the wall mounting bracket and the wall.
8
SPECIFICATIONS
Maximum
Minimum
241.6
272.6
303.6
494
800
550
600.5
651
860
200
220
Model name
LSW840B
Width (mm)
860
Height (mm)
494
Depth (mm)
27
Product weight (kg)
8.7
Wall mounting bracket VESA specifications
800X400
Max. tensile load (kg)
100
27
47
9
ENGLISH
[Unit: mm]
The model and serial number of the product is located on
the back or one side of the product. Record it below
should you ever need service.
MODEL
SERIAL
Supported Displays
(Please contract the retailers or refer to the TV owner’s
manual for applicable models.)
Download PDF