LG RT-44NA21T Owner’s Manual

Colour Television
OWNER'S MANUAL
Please read this manual
carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the back
mation to your dealer when you
Model number
:
Serial number
:
P/NO
:
3828VA0291B
(MP015A,
cover
require
084T/V
TX)
a
and
quote this infor-
service.
Contents
Installation
3
Location and function of controls
Remote control handset
Internal generator charge
Battery installation
Front panel / Side panel
4
Basic operation
On and off / Programme selection
Volume adjustment / Quick view
Mute function / Auto Demonstration
On screen language selection (option)
7
On
8
screen menus
Menu selection
up TV stations
Auto programme tuning
Manual programme tuning
Fine tuning
Programme edit
Calling the programme table
9
Setting
Picture adjustment
PSM (Picture Status Memory)
Picture adjustment / 100Hz mode
Convergence / Turbo picture selection
14
Sound adjustment
SSM (Sound Status Memory) / Sound adjustment
Turbo sound selection
Sound output selection / Stereo/Dual reception
NICAM reception (option)
16
Other functions
TV and AV modes / VGA mode (option)
Auto AV switching (option)
Child lock / Auto sleep
Blue back (option) / Sleep timer
18
PIP
21
operation (option)
On and off / Input mode selection for sub picture
Swapping between main and sub pictures
Programme selection for sub picture
Sub picture size / Sub picture freeze
Sub picture position change / Programme scan
Teletext (option)
Switch on/off
SIMPLE text / TOP text (option)
FASTEXT / Special teletext functions
22
Connection of external equipment
Aerial socket
Audio/Video in sockets (option)
Euro scart socket (option)
S-video / Audio in sockets (S-AV) (option)
Component in sockets (option)
PC Input / Audio in sockets (option)
25
Troubleshooting
2
check list
Back
cover
Installation
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set.
In the event of thunderstorms
ial and mains
or
powercuts, please pull
out the aer-
plugs.
Warning
To prevent fire
moisture.
or
shock hazard, do not expose the set to rain
or
Service
Never
remove
the back
high voltage
properly, unplug it
very
cover of the set as this can expose you to
and other hazards. If the set does not operate
and call your dealer.
Aerial
Connect the aerial cable to the socket marked +75 Ω
For the best
cover.
reception
an
on
the back
outdoor aerial should be used.
Location
Position your set so that no bright light or sunlight falls directly onto
screen. Care should be taken not to expose the set to any
unnecessary vibration, moisture, dust or heat. Also ensure that the
the
set is
in
a position to allow a free flow
openings on the back cover.
place the set on a sloping or unstable
placed
of air. Do not
cover
the ventilation
Do not
on
the bottom of the set may
cause
it to
move
area as
the casters
and to be
damaged.
When displaying still pictures such as videogames, 16:9 picture format, PIP display, and station label for a long time, the image may
be persisted on the screen.
Manufactured under license from Dolby Laboratories. "Dolby"
"Pro Logic" and the double-D symbol are trademarks of Dolby
Laboratories.
3
Location and function of controls
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the front
panel of the set.
Remote control handset
POWER
1
I/II
2
Before you use the remote control handset,
10 teries. See the next page.
TV/AV
PICTURE
11
PIP
TEXT
PR-
PR+
SWAP
1.
12
4
2.
INPUT
13
MENU
PR
MUTE
14
5
VOL
OK
VOL
PSM
0
SSM
POSITION
SCAN
STILL
TIME
REVEAL
SIZE
MIX
SLEEP
M
15
?
LIST
16 5.
17
STOP
REW
P/STILL
PLAY
REC
I/II
selects the language during dual
selects the sound output.
6.
FF
MENU
selects
standby.
language
broadcast.
OK
a menu.
menu
settings.
accepts your selection
7.
pictures
Δ / Ε (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
Φ / Γ (Volume Up/Down)
adjusts the volume.
adjusts
(With TELETEXT)
off to
or
SWAP
alternates between main and sub picture.
INPUT
selects the input mode for the sub picture.
SIZE
adjusts the sub picture size.
STILL
freezes motion of the sub picture.
POSITION
relocates the sub picture in clockwise direction.
SCAN
switches on or off the programme scan mode 12 sub
456
8
standby
PIP BUTTONS
PIP
switches the sub picture on or off.
PR +/selects a programme for the sub picture.
7
9
from
4.
123
8
on
TURBO SOUND BUTTON
selects Turbo sound.
PR
7
POWER
switches the set
3.
6
4
install the bat-
TURBO
SOUND
3
9
please
or
NUMBER BUTTONS
switches the set on from
displays
standby
the current mode.
or
directly
8.
PSM (Picture Status
recalls your preferred
9.
VCR BUTTONS
control a LG video cassette recorder.
Memory)
picture setting.
select
a
number.
.
Location and function of controls
10. TV/AV
selects TV or AV mode.
clears the menu / text from the screen.
switches the set on from standby.
11. TURBO PICTURE BUTTON
selects Turbo
POWER
picture.
1
I/II
12. TELETEXT BUTTONS (option)
These buttons are used for teletext.
For further details, see the 'Teletext' section.
2
TV/AV
10
TURBO
SOUND
PICTURE
11
3
PIP
4
13. SWAP
returns to the
previously
PR-
viewed programme.
PR+
SWAP
14. MUTE
switches the sound
on or
INPUT
13
off.
MENU
PR
MUTE
5
14
15. SSM (Sound Status Memory)
recalls your preferred sound setting.
VOL
16. LIST
OK
VOL
6
displays
17. SLEEP
sets the
the programme table.
sleep
timer.
PR
Note : In teletext mode, the PR +/-, SWAP and INPUT buttons
used for teletext function.
are
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
SCAN
STILL
SLEEP
LIST
7
Battery
installation
The remote control handset is powered by two AAA type batteries. 8
To load the batteries, turn the remote control handset over and
open the battery compartment. Install two batteries as indicated by
the polarity symbols ( + and
) marked inside the compartment.
-
15
SIZE
16
17
STOP
9
REW
P/STILL
PLAY
REC
FF
Note : To avoid damage from possible battery leakage, remove the
batteries if you do not plan to use the remote control handset for an
extended period of time.
(Without TELETEXT)
5
Location and function of controls
Front
?
panel
RT-54/49/44NA11T series
S-VIDEO
9
8
TV/AV
OK
MENU
VOL
MUTE
L/MON
AUDIO
PR
R
IN3
TVAV
OK
MNU
MUTE
1
OL
PR
10
POWR
7
?
654
RT-54/44NA21T series
2
8
PR
MUTE
PR
MENU
VOL
PR
MUTE
PR
MENU
VOL
OK
VOL
TV/AV
4567
OK
VOL
TV/AV
ONOFF
13
?
PCINUT
2
3
ON/OFF
9
RT-54/44NA41T series
S-VIDEOL/MN
AUDIO
R
PR
MUTE
PR
MENU
2
8
PR
MUTE
PR
OK
VOL
TV/AV
MENU
VOL
OK
VOL
1
VOL
TV/AV
POWER
4
AV3
567
(Side panel)
3
1.
2.
MAIN POWER
switches the set
on or
8.
REMOTE CONTROL SENSOR
9.
AUDIO/VIDEO IN SOCKETS (AV3 or IN3)
Connect the audio/video out sockets of external equipment to these sockets.
S-VIDEO/AUDIO IN SOCKETS (S-AV)
Connect the video out socket of an S-VIDEO
VCR to the S-VIDEO socket.
Connect the audio out sockets of the SVIDEO VCR to the audio sockets as in AV3 or
IN3.
off.
Φ / Γ
(Volume Up/Down)
adjusts the volume.
adjusts menu settings.
Δ / Ε (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
3.
POWER/STANDBY INDICATOR
illuminates brightly when the set is in
mode.
dims when the set is switched on.
4.
MUTE
switches the sound
5.
MENU
selects
6.
on or
10. PC INPUT SOCKET (option)
Connect the PC cable from the monitor output
socket of the PERSONAL COMPUTER to this
socket.
*
CASTERS (on the bottom)
turn and move the set
OK
mode.
6
off.
a menu.
accepts your selection
7.
standby
or
displays
the current
TV/AV
selects TV or AV mode.
clears the menu / text from the screen.
switches the set on from standby.
easily.
Basic
operation
On and off
1.
2.
3.
4.
Press the main power button to switch the set on.
If the set is in standby mode, press the POWER, Δ / Ε, TV/AV or
NUMBER buttons on the remote control handset to switch it on fully.
Press the POWER button on the remote control handset.
The set reverts to standby mode.
Press the main power button again to switch the set off.
Note : If, while the set is switched on, the mains plug is disconnected the set will switch to standby or power on when the mains
plug is replaced in the mains power socket.
POWER
I/II
TV/AV
TURBO
SOUND
Programme
selection
You can select
buttons.
a
PICTURE
PIP
programme number with the Δ / Ε
or
NUMBER
TEXT
PR-
PR+
SWAP
INPUT
Volume
MENU
adjustment
Press the Φ / Γ button to
adjust
INPUT
PR
MUTE
the volume.
VOL
OK
VOL
Quick view
Press the SWAP button to view the last programme you
were
watching.
PR
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
Mute function
Press the MUTE button. The sound is switched off and the
W appears.
You can cancel it
SOUND button.
by pressing
the MUTE, Φ
display
/ Γ, I/II, TURBO
?
Auto Demonstration
MIX
programmed in the set, press the OK butpanel control for about 5 seconds. To stop auto
demonstration, press any button of the front panel control and
POWER button of the remote control.
To review all the
ton of the front
On
screen
SLEEP
M
menus
language
selection
The menu can be displayed
First select your language.
on
the
LIST
EYE
STOP
REW
P/STILL
PLAY
REC
FF
(option)
screen
in desired
language.
1.
2.
3.
Press the MENU button to select the Station menu.
Press the Γ button and then Δ / Ε button to select Language.
Press the Γ button and then Δ / Ε button to select your desired
4.
All the on screen displays will appear in the selected language.
Press the OK or Φ button to select the Station menu.
Press the TV/AV button to return to normal TV viewing.
language.
7
On
screen menus
The
an
dialogue
operator
also
between you and your set takes place on screen with
The buttons required for the operating steps are
menu.
displayed.
Menu selection
1.
2.
3.
Repeatedly press
4.
Change
the MENU button to display each menu.
Press the Γ button and then Δ / Ε button to select a menu item.
Press the Γ button to display the sub menu or the pull-down
menu.
the
setting
of
an
item in the sub
or
Φ/ΓorΔ/Ε.
POWER
pull-down
menu
with
can move to the higher level menu with OK or Φ button and
to move to the lower level menu press the Γ button
You
I/II
TV/AV
TURBO
SOUND
PICTURE
PIP
TEXT
PR-
PR+
INPUT
SWAP
MENU
Note :
In the AV modes, the Station menu is not displayed.
a.
b. In the teletext mode, menus are not displayed.
In some models, the Normal/Turbo search will not display,
c.
only the Start will display in the Auto programme menu.
d. In some models, the Language, AV4 will not display.
INPUT
PR
MUTE
CH.
VOL
OK
VOL
AutoOprogramme
ManualOprogramme
{
System
StorageOfrom
{
OBG
{
{
OOI
ProgrammeOedit
{
NormalOsearch
{
ODK
Language
{
TurboOsearch
{
OOM
1
()O{OOKOMENUOTV
Station
PR
1
2
3
4
5
6
CH.
7
8
9
PSM
0
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
M
P/STILL
PLAY
AV
menu
{
PR.
{
User
{
System
{
100Hz
{
Channel
{
C onvergence
{
Fine
{
Search
{
Name
{
Booster
{
PSM
()O{OOKOMENUOTV
?
Picture
AV
()O}{OOKOMENUOTV
AV
menu
LIST
CH.
REW
()O}{OOKOMENUOTV
SSM
EYE
STOP
AV
0O-O-O-O-O- OO 05O SO 6O9
SSM
{
Balance
{
1O CO 0O3OO06O SO 1O7
AVL
{
2O CO 1O2OO07O SO 2O2
3O SO 6O6OO08O CO 0O9
REC
4O SO 6O7OO09O CO 1O1
DeleteOOOCopy
FF
MoveOOOOOSkip
()O{OOKOMENUOTV
Sound
CH.
()O}{OOKOMENUOTV
menu
Input
{
ChildOlock
{
AutoOsleep
{
BlueOback
{
()O{OOKOMENUOTV
Special
TV programme
8
AV
AV
menu
AV
Setting up
TV stations
Up to 100 TV stations can be stored by programme numbers (0 to 99).
Once you have preset the stations, you will be able to use the Δ / Ε
or NUMBER buttons to scan the stations you programmed.
Stations can be tuned using automatic or manual modes.
Note
:
In
some
models up to 200 TV stations
Auto programme
can
CH.
AutoOprogramme
ManualOprogramme
{
ProgrammeOedit
{
Language
{
Station
Menu
{
be stored.
tuning
()O{OOKOMENUOTV
AV
All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set.
1.
2.
3.
the MENU button to select the Station menu.
Press the Γ button and then Δ / Ε button to select Auto programme.
Press the Γ button to display the Auto programme menu.
Repeatedly press
POWER
I/II
TV/AV
TURBO
SOUND
System
StorageOfrom
{
OBG
{
OOI
NormalOsearch
{
ODK
TurboOsearch
{
OOM
PICTURE
PIP
TEXT
PR-
PR+
SWAP
INPUT
()O}{OOKOMENUOTV
4.
MENU
AV
Press the Γ button. Select a TV system with the Δ / Ε button
the System pull-down menu;
BG : (Asia/New Zealand/M.East/Africa/Australia)
I
: (Hong Kong/South Africa)
DK : (East Europe/China/Africa/CIS)
M
: (USA/Korea/Philippines) (option)
Press the OK or Φ button.
Press the Δ / Ε button to select Storage from.
Press the Γ button. Select the beginning programme number
with the Φ / Γ button or NUMBER buttons on the Storage
from pull-down menu. Any number under 10 is entered with a
numeric '0' (or '00') in front of it, i.e. '05' (or '005') for 5.
Press the OK button.
Press the Δ / Ε button to select Normal or Turbo search.
on
5.
6.
7.
8.
9.
Option:
In
some
models, you
only
can
select Start.
Note :
a.
Turbo search is further faster than Normal search and in some
models, these searches will automatically store all receivable stations.
b. If the programmed station has poor quality sound, select the
system again in the Manual programme menu.
10. Press the Γ button to begin auto programming.
System
StorageOfrom
{
NormalOsearch
{
TurboOsearch
{
{
OOCO01O(BG)
System
StorageOfrom
{
NormalOsearch
{
TurboOsearch
{
77O7O7O736%
MENU
VOL
PR
MUTE
OK
VOL
PR
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
M
?
LIST
EYE
STOP
REW
{
INPUT
P/STILL
PLAY
REC
FF
OOCO01O(BG)
77O7O7O736%
MENU
(Normal search)
(Turbo search)
All receivable stations are stored.
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit
menu appears on the screen. See the 'Programme edit' section
to edit the stored programme.
11. Press the TV/AV button to return to normal TV
viewing.
9
Setting up
Station
Menu
CH.
AutoOprogramme
ManualOprogramme
{
ProgrammeOedit
{
Language
{
()O{OOKOMENUOTV
{
Manual programme
AV
POWER
2.
the MENU button to select the Station menu.
Press the Γ button and then Δ / Ε button to select Manual
3.
programme.
Press the Γ button to
TV/AV
TURBO
SOUND
PICTURE
PIP
TEXT
PR-
PR+
INPUT
SWAP
MENU
MUTE
4.
5.
VOL
OK
VOL
6.
7.
8.
PR
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
M
9.
10.
11.
?
LIST
EYE
STOP
REW
P/STILL
PLAY
REC
FF
Repeatedly press
display
the Manual programme
PR.
{
System
{
Channel
{
Fine
{
Search
{
Name
{
Booster
{
()O}{OOKOMENUOTV
INPUT
PR
tuning
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station
name with five characters to each programme number.
1.
I/II
TV stations
12.
13.
14.
15.
1
AV
Press the Δ / Ε button to select PR..
Press the Γ button to select the programme number. Select the
desired programme number (0 to 99) with the Φ / Γ button or
NUMBER buttons on the PR. pull-down menu. Any number
under 10 is entered with a numeric '0' (or '00') in front of it, i.e.
'05' (or '005') for 5.
Press the OK button.
Press the Δ / Ε button to select System.
Press the Γ button. Select a TV system with the Δ / Ε button
on the System pull-down menu;
BG : (Asia/New Zealand/M.East/Africa/Australia)
I
: (Hong Kong/South Africa)
DK : (East Europe/China/Africa/CIS)
M
: (USA/Korea/Philippines) (option)
Press the OK or Φ button.
Press the Δ / Ε button to select Channel.
Press the Γ button. Press the Δ / Ε button to select V/UHF or
Cable on the Channel pull-down menu.
If possible, select the channel number directly with the number
buttons. Any number under 10 is entered with a numeric '0' (or
'00') in front of it, i.e. '05' (or '005') for 5.
Press the OK or Φ button
Press the Δ / Ε button to select Search.
Press the Γ button. Press the Φ / Γ button to commence
searching on the Search pull-down menu. If a station is found
the search will stop.
Press the OK button to store it. The display Stored will appear.
PR.
{
System
{
Channel
{
Fine
{
Search
{
Name
{
Booster
{
{{{{
Stored
16. To store another station, repeat steps 4 to 15.
17. Press the TV/AV button to return to normal TV
10
menu.
viewing.
Setting up
Assigning a station name
1. Repeat the 'Manual programme tuning' steps
2.
3.
4.
5.
6.
7.
TV stations
CH.
1 to 3.
Press the Δ / Ε button to select Name.
Press the Γ button on the Name pull-down menu.
Press the Δ button. You can use a blank, +, -, the numeric 0 to 9
and the alphabet A to Z.
With the Ε button you can select in the opposite direction.
Select the position by pressing the Φ / Γ button and then take
your choice of the second character, and so on.
Press the OK button.
Press the TV/AV button to return to normal TV viewing.
Booster
When the interference between programmes appear, select Booster
to Off.
AutoOprogramme
ManualOprogramme
{
ProgrammeOedit
{
Language
{
()O{OOKOMENUOTV
Station
Menu
{
AV
POWER
I/II
TV/AV
TURBO
SOUND
PICTURE
PIP
TEXT
PR-
1.
2.
3.
4.
5.
6.
Repeat the 'Manual programme tuning' steps 1 to 3.
Press the Δ / Ε button to select Booster.
Press the Γ button.
Press the Δ / Ε button to select On or Off on the Booster
down menu.
Press the OK or Φ button.
Press the TV/AV button to return to normal TV viewing.
Fine
PR+
SWAP
INPUT
MENU
INPUT
PR
MUTE
pullVOL
OK
VOL
tuning
PR
Normally
1.
2.
3.
4.
fine
tuning
is
if
only necessary
reception
is poor.
the 'Manual programme tuning' steps 1 to 3.
Press the Δ / Ε button to select Fine.
Press the Γ button.
Press the Φ / Γ button to fine tune for the best picture and
sound on the Fine pull-down menu.
Repeat
PR.
{
System
{
Channel
{
Fine
{
Search
{
Name
{
Booster
{
{{{{
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
LIST
P/STILL
REC
AV
REW
5.
6.
M
EYE
STOP
}{OOKOMENUOTV
SLEEP
?
PLAY
FF
Press the OK button.
Press the TV/AV button to return to normal TV viewing.
The finely tuned programme will be indicated by yellow number
during programme selection.
11
Setting up
Station
Menu
CH.
AutoOprogramme
ManualOprogramme
{
ProgrammeOedit
{
Language
{
()O{OOKOMENUOTV
AV
{
Programme
TV stations
edit
This function enables you to delete or skip the stored programmes.
Also you can move some stations to other programme numbers or
insert a blank station data into the selected programme number.
1.
2.
3.
the MENU button to select the Station menu.
button and then Δ / Ε
button to select
Programme edit.
Press the Γ button to display the Programme edit menu.
Repeatedly press
Press
the
POWER
Γ
0O-O-O-O-O- OO 05O SO 6O9
1O CO 0O3OO06O SO 1O7
2O CO 1O2OO07O SO 2O2
I/II
TV/AV
3O SO 6O6OO08O CO 0O9
4O SO 6O7OO09O CO 1O1
TURBO
SOUND
PICTURE
PIP
DeleteOOOCopy
MoveOOOOOSkip
TEXT
()O}{OOKOMENUOTV
PR-
PR+
INPUT
SWAP
MENU
INPUT
PR
Deleting
1.
2.
MUTE
AV
a
programme
Select a programme to be deleted with the Δ / Ε or Φ / Γ button.
Press the RED button twice.
The selected programme is deleted, all the following programmes are shifted up one position.
0O-O-O-O-O- OO 05O SO 6O9
VOL
1O CO 0O3OO06O SO 1O7
OK
VOL
2O CO 1O2OO07O SO 2O2
3O SO 6O6OO08O CO 0O9
4O SO 6O7OO09O CO 1O1
Delete
MENUOTV
AV
PR
Copying
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
M
1.
2.
programme
Select a programme to be copied with the Δ / Ε
Press the GREEN button.
All the following programmes are shifted down
Moving
1.
2.
3.
a
or Φ
one
/ Γ button.
position.
a
programme
Select a programme to be moved with the Δ / Ε or Φ / Γ button.
Press the YELLOW button.
Move the programme to the desired programme number with
theΔ/ΕorΦ/Γbutton.
?
4.
Press the YELLOW button
LIST
0O-O-O-O-O-
again
to release this function.
O05O SO 6O9
1O CO 0O3OO06O SO 1O7
EYE
2O CO 1O2OO07O SO 2O2
3O SO 6O6OO08O CO 0O9
STOP
REW
P/STILL
PLAY
REC
4O SO 6O7OO09O CO 1O1
FF
MoveOOff
()O}{OMENUOTV
Skipping
1.
2.
3.
a
AV
programme number
programme number to be
Select a
skipped with the Δ / Ε or Φ / Γ
button.
Press the BLUE button. The skipped programme turns to blue.
Press the BLUE button again to release the skipped pro-
gramme.
When a programme number is skipped it means that you will be
unable to select it using the Δ / Ε button during normal TV
viewing. If you want to select the skipped programme, directly
enter the programme number with the NUMBER buttons or
select it in the programme edit or table menu.
Press the TV/AV button to return to normal TV
12
viewing.
Setting up
Calling
TV stations
the programme table
can check the programmes stored in the memory
the programme table.
You
Displaying programme
table
Press the LIST button to
display
the
Programme
by displaying
table
menu.
The programme table appears on the screen. One programme
table contains ten programmes as below.
0O-O-O-O-O-
POWER
I/II
O05O SO 6O9
1O CO 0O3OO06O SO 1O7
TV/AV
TURBO
SOUND
2O CO 1O2OO07O SO 2O2
PICTURE
3O SO 6O6OO08O CO 0O9
4O SO 6O7OO09O CO 1O1
PIP
TEXT
PR-
()O}{OOKOMENUOTV
Note
AV
PR+
SWAP
INPUT
:
MENU
a.
You may find some blue programmes. They have been set up to
be skipped by auto programming or in the programme edit mode.
b.
Some programmes with the channel number shown in the programme table indicate there is no station name assigned.
VOL
programme in the programme table
programme with the Δ / Ε or Φ / Γ button.
Then press the OK button.
Selecting
Select
INPUT
PR
MUTE
OK
VOL
a
a
The set switches to the chosen programme number.
Paging through a programme table
There are 10 (or 20) programme table pages in which contain 100
(or 200) programmes.
Pressing the Δ / Ε or Φ / Γ button repeatedly turns the pages.
Press the TV/AV button to return to normal TV
viewing.
PR
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
M
?
LIST
EYE
STOP
REW
P/STILL
PLAY
REC
FF
13
Picture
Picture
Menu
CH.
PSM
{
User
{
100Hz
{
C onvergence
{
adjustment
PSM (Picture Status Memory)
1.
Repeatedly press the MENU button
2.
3.
to select the Picture menu.
Press the Γ button and then Δ / Ε button to select PSM.
Press the Γ button and then Δ / Ε button to select a picture
setting on the PSM pull-down menu.
CH.
()O{OOKOMENUOTV
AV
PSM
{
Dynamic
User
{
Standard
100Hz
{
Mild
C onvergence
{
Game
User
POWER
()O}OOKOMENUOTV
I/II
4.
5.
TURBO
SOUND
PICTURE
You
PIP
TEXT
PR-
PR+
Press the OK or Φ button.
Press the TV/AV button to return to normal TV
INPUT
PR
MUTE
You
OK
adjustment
adjust picture contrast, brightness, colour intensity, sharpness and tint (NTSC input only) to the levels you prefer.
1.
Repeatedly press the MENU button to select the Picture menu.
2.
3.
VOL
viewing.
also recall a desired picture (Dynamic, Standard,
Mild, Game or User) with PSM button on the remote control. The
picture Dynamic, Standard, Mild and Game are programmed
for good picture reproduction at the factory and cannot be changed.
can
Picture
INPUT
SWAP
MENU
AV
TV/AV
can
Press the Γ button and then Δ / Ε button to select User.
Press the Γ button and then Δ / Ε button to select the desired
picture item on the User pull-down menu.
VOL
CH.
PSM
{
User
{
Contrast
{
100Hz
{
{
C onvergence
{
Brightness
Colour
{
Sharpness
{
PR
()O}{O OKOMENUOTV
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
4.
5.
AV
Press the Γ button.
Press the Φ / Γ button to make
each sub menu.
appropriate adjustments
Contrast
MIX
SLEEP
M
LIST
EYE
STOP
REW
P/STILL
PLAY
REC
FF
()O}{O OKOMENUOTV
?
6.
7.
on
80
AV
You can also select other User items directly with Δ / Ε button
and adjust them with Φ / Γ button.
Press the OK button to store it for the picture User.
Press the TV/AV button to return to normal TV viewing.
100Hz mode
When watching VCR, select desired
Mode 1 or Mode 2.
1.
2.
3.
condition
by choosing
press the MENU button to select the Picture menu.
Press the Γ button and then Δ / Ε button to select 100Hz.
Γ
Press the
button and then Δ / Ε button to select a picture
setting (Mode 1 or 2) on the 100Hz pull-down menu.
PSM
{
User
{
100Hz
{
Mode1
C onvergence
{
Mode2
()O}OOKOMENUOTV
4.
5.
picture
Repeatedly
CH.
AV
Press the OK or Φ button.
Press the TV/AV button to return to normal TV
viewing.
Note :
a.
This mode works only in AV mode and TV programme 0.
b.
The 100Hz mode isn't suitable to use NTSC signal.
14
the
Picture
adjustment
Convergence
CH.
This function enables you to adjust the colour convergence of
screen during receiving the signals. When the set is first installed or
it is relocated, the picture may be unstable with three colour ghosts
(red, green, blue). This problem can be solved by adjusting the
colour convergence.
1. Repeatedly press the MENU button to select the Picture menu.
2. Press the Γ button and then Δ / Ε
button to select
3.
Convergence.
Press the Γ button to
If the
display
the
{
User
{
100Hz
{
C onvergence
{
()O{OOKOMENUOTV
Picture
Menu
AV
POWER
Convergence
unstable with three colour
convergence needs to be adjusted.
display
PSM
+ are
menu.
ghosts,
I/II
the colour
TV/AV
TURBO
SOUND
PICTURE
PIP
TEXT
PR-
PR+
SWAP
INPUT
INPUT
Convergence
MENU
OK TV/AV
4.
5.
If the display + is white, colour convergence adjustment is not
necessary.
Press the OK button to adjust the colour convergence.
The display Δ Ε Φ Γ is selected in red.
Press it again to select the display Δ Ε Φ Γ in blue.
Press the Δ / Ε / Φ / Γ button to superimpose the display +
(red or blue) with the green one.
The display + is moved to the left, right, up or down by pressing
VOL
7.
If the red and blue display + are superimposed with the green
one, the display + will be changed to yellow or cyan.
Press the TV/AV button to return to normal TV viewing.
Note :The convergence isn't suitable to
use
in
case
of
no
picture
selection
When this function is on, picture will be more brilliant and distinct
picture than normal picture. You can enjoy the Turbo picture so
much better than normal picture.
Repeatedly press the TURBO PICTURE button to switch on or off.
VOL
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
STOP
REW
(Turbo Picture off)
OK
broad-
casting signal.
Turbo
MUTE
PR
theΔ/Ε/Φ/Γbutton.
6.
PR
SLEEP
M
P/STILL
PLAY
?
LIST
REC
FF
(Turbo Picture on)
15
Sound
Sound
Menu
CH.
SSM
{
Balance
{
AVL
{
SSM
adjustment
(Sound Status Memory)
You can select your preferred sound setting; Dolby Virtual, Music,
Movie or Sports and you can also adjust the sound frequency of
equalizer.
()O{OOKOMENUOTV
AV
1.
2.
3.
press the MENU button to select the Sound menu.
Press the Γ button and then Δ / Ε button to select SSM.
Press the Γ button and then Δ / Ε button to select a sound setting on the SSM pull-down menu.
Repeatedly
CH.
POWER
SSM
{
Dolby0Virtual
Balance
{
AVL
{
Music
Movie
Sports
I/II
User
TV/AV
{
TURBO
SOUND
PICTURE
()O}{O OKOMENUOTV
PIP
PR-
Dolby Virtual
Dolby Virtual lets
PR+
INPUT
SWAP
MENU
AV
TEXT
INPUT
PR
you
experience panoramic
Sound Frequency Adjustment
a. Press the Γ button in User to
display
effects of sound.
the User sub
menu.
MUTE
0.1O0.5O1.5O5.0O10OkHz
()O}{O OKOMENUOTV
VOL
OK
VOL
Sound
PR
1
2
You
adjustment
adjust
matically keeps
3
can
4
5
6
grammes.
7
8
9
1.
2.
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
M
AV
b. Select a sound band by pressing the Φ / Γ button.
c. Make appropriate sound level with the Δ / Ε button.
d. Press the OK button to store it for the sound User.
The display Stored appears.
Press the TV/AV button to return to normal TV viewing.
3.
?
balance
on an
AVL (Auto Volume Leveler). AVL autovolume level even if you change pro-
press the MENU button to select the Sound menu.
Press the Γ button and then Δ / Ε button to select the desired
sound item; Balance or AVL.
Make desired adjustment with the Φ / Γ, Δ / Ε or OK button
on each pull-down menu.
Repeatedly
CH.
LIST
or
equal
SSM
{
Balance
{
AVL
{
On
Off
EYE
STOP
P/STILL
REC
()O}{O OKOMENUOTV
REW
PLAY
AV
FF
4.
Press the TV/AV button to return to normal TV
viewing.
Turbo sound selection
When this function is on, sound will be more emphasized and
amplified sound than normal sound. You can enjoy the Turbo
Sound so much better than normal Sound.
Repeatedly press the TURBO SOUND button to switch on or off.
(Turbo Sound off)
16
(Turbo Sound on)
Sound
adjustment
Sound output selection
In AV mode, you
can
speakers.
select output sound for the left and
right
loud-
Repeatedly press the I/II button to select the sound output.
:
Audio signal from audio L input is sent to left loud-speaker
and audio signal from audio R input is sent to right loudspeaker.
L+L :
Audio signal from audio L input is sent to left and right loudspeakers.
R+R :
Audio signal from audio R input is sent to left and right loudspeakers.
L+R
POWER
I/II
TV/AV
TURBO
SOUND
Stereo/Dual
reception
PICTURE
PIP
When
a programme is selected, the sound information for the station
appears after the programme number and station name disappear.
TEXT
PR-
PR+
INPUT
SWAP
Broadcast
On Screen
Mono
MONO
Stereo
STEREO
Dual
DUAL I
Display
MENU
VOL
Mono sound selection
In stereo reception if the stereo signal is weak, you can switch to
mono by pressing the I/II button twice. In mono reception the depth
of sound is improved. To switch back to stereo, press the I/II button twice again.
Language selection for dual language broadcast
If a programme received in two languages (dual language), you can
switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II button
repeatedly.
DUAL I sends the primary broadcast language to the loudspeakers.
DUAL II sends the secondary broadcast language to the loud-
speakers.
DUAL I+II sends
NICAM
a
separate language
to each
loudspeaker.
3.
MUTE
OK
VOL
PR
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
M
equipped
?
LIST
EYE
STOP
with the receiver for NICAM reception, the
high quality NICAM (Near Instantaneous Companding Audio
Multiplex) digital sound can be received.
Sound output can be selected according to the type of received
broadcast as follows by pressing the I/II button repeatedly.
2.
PR
reception (option)
If your set is
1.
INPUT
REW
P/STILL
PLAY
REC
FF
When NICAM mono is received, you can select NICAM
MONO or FM MONO.
When NICAM stereo is received, you can select NICAM
STEREO or FM MONO. If the stereo signal is weak, switch to
FM mono.
When NICAM dual is received, you can select NICAM DUAL
I, NICAM DUAL II or NICAM DUAL I+II or MONO. When
FM mono is selected the display MONO appears on the
screen.
17
Other functions
Special
Menu
CH.
Input
{
ChildOlock
{
AutoOsleep
{
BlueOback
{
TV and AV modes
Inputs can be set for TV or AV mode. AV mode is used when a video
cassette recorder (VCR), or other equipment is connected to the set.
Note : When a VCR is connected via the aerial socket the set is used
in TV mode. See the 'Connection of external equipment' section.
()O{OOKOMENUOTV
AV
1.
2.
3.
POWER
I/II
SOUND
the MENU button to select the Special menu.
Press the Γ button and then Δ / Ε button to select Input.
Press the Γ button and then Δ / Ε button to select TV, AV1,
AV2, AV3, AV4 (option), COMPONENT 1, COMPONENT 2 or
VGA (option) on the Input pull-down menu.
Repeatedly press
TV/AV
TURBO
PIP
CH.
PICTURE
Input
{
TV
ChildOlock
{
AutoOsleep
{
BlueOback
{
AV1
AV2
AV3
AV4
COMPONENT1
COMPONENT2
VGA
TEXT
PR-
PR+
INPUT
SWAP
MENU
VOL
INPUT
PR
()O}OOKOMENUOTV
MUTE
OK
AV 1 : VCR connected to the AV1 sockets on the set
AV 2 : VCR connected to the AV2 sockets on the set
AV 3 : VCR connected to the AV3 sockets on the set
AV4 : VCR connected to the Euro scart socket on the set (option)
COMPONENT 1 : COMPONENT connected to the COMPONENT 1 sockets on the back
COMPONENT 2 : COMPONENT connected to the COMPONENT 2 sockets on the back
VGA : PC connected to the PC INPUT sockets on the back
VOL
PR
4.
1
2
(option)
Press the TV/AV button to return to normal TV
viewing.
3
Alternatively
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
M
LIST
EYE
STOP
AV
P/STILL
you
TV/AV button.
can
select the TV
or
AV mode
In AV mode, to return to TV mode, press the Δ / Ε
VGA mode
?
or
by pressing
the
NUMBER buttons.
(option)
You can adjust picture contrast, brightness, convergence.
1. Press the MENU button to select the Special menu.
2. Press the Γ button and then Δ / Ε button to select Input.
3. Press the Γ button and then Δ / Ε button to select VGA on the
Input pull-down
menu.
REC
OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO
REW
PLAY
O
FF
O
O
O
O
Input
{
Contrast
{
Brightness
{
V-Position
H-Position
{
Convergence
{
{
TV
AV1
AV2
AV3
AV4
COMPONENT1
COMPONENT2
VGA
O
()O}{O OKOMENUOTV
4.
5.
Press the MENU button.
Press the Δ / Ε button to select Contrast, Brightness, VPosition, H-Position or Convergence on the VGA mode
menu.
18
AV
Other functions
Contrast
This function is to
adjust
Brightness
This function is to
adjust
the
the
display
display
CH.
to the contrast desired.
to the
brightness
Horizontal Position / Vertical Position
This function is to adjust picture to left/right and
Input
{
ChildOlock
{
AutoOsleep
{
BlueOback
{
Special
Menu
desired.
()O{OOKOMENUOTV
up/down
as
AV
you
prefer.
POWER
Convergence
This function enables you to adjust the colour convergence of
screen during receiving the signals.
I/II
TV/AV
TURBO
SOUND
Note :The convergence isn't suitable to
use
in
case
PICTURE
of no PC cable
PIP
signal.
TEXT
PR-
Auto AV
switching (option)
If your VCR outputs switching voltage when it is switched to playback with the VCR connected to the Euro scart socket. The set is
automatically switched to AV 1 mode when an AV signal is input.
But if you want to keep on watching TV mode, press the Δ / Ε or
NUMBER buttons.
Press the TV/AV button to return to AV modes.
PR+
INPUT
SWAP
MENU
VOL
INPUT
PR
MUTE
OK
VOL
Child lock
PR
The TV can be set so that the remote control handset is needed to
control it. This feature can be used to prevent unauthorized view-
1
2
3
ing.
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
1.
2.
3.
4.
the MENU button to select the Special menu.
Press the Γ button and then Δ / Ε button to select Child lock.
Press the Γ button and then Δ / Ε button to select On or Off
on the Child lock pull-down menu.
Press the TV/AV button to return to normal TV viewing.
Repeatedly press
With the lock on, the display Child lock on appears on the screen
if any button on the front panel is pressed while viewing the TV.
Note
The
any button
:
menus.
display Child lock on will not appear on the screen if
on the front panel is pressed while displaying the
M
?
LIST
EYE
STOP
REW
P/STILL
PLAY
REC
FF
19
Other functions
Special
Menu
CH.
Input
{
ChildOlock
{
AutoOsleep
{
BlueOback
{
Auto
sleep
If you select On on the Auto sleep pull-down menu, the set will
switch itself to standby mode approximately ten minutes after a TV station stops broadcasting.
automatically
()O{OOKOMENUOTV
AV
POWER
4.
I/II
TURBO
Blue back
PICTURE
PIP
TEXT
PR-
PR+
SWAP
INPUT
INPUT
PR
MUTE
OK
(option)
If you select On
on
ground appears
on
1.
2.
3.
4.
VOL
the MENU button to select the Special menu.
Press the Γ button and then Δ / Ε button to select Auto sleep.
Press the Γ button and then Δ / Ε button to select On or Off on
the Auto sleep pull-down menu.
Press the TV/AV button to return to normal TV viewing.
Repeatedly press
TV/AV
SOUND
MENU
1.
2.
3.
the Blue back pull-down menu, the blue backthe screen when there is no or poor signal.
the MENU button to select the Special menu.
Press the Γ button and then Δ/Ε button to select Blue back.
Press the Γ button and then Δ / Ε button to select On or Off on
the Blue back pull-down menu.
Press the TV/AV button to return to normal TV viewing.
Repeatedly press
VOL
Note :
a.
The blue background automatically appears on the screen
when there is no signal in AV mode.
b. The Blue back isn't suitable to use COMPONENT 2 mode.
PR
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
M
LIST
EYE
STOP
REW
20
P/STILL
PLAY
REC
FF
Sleep
?
timer
You don't have to remember to switch the set off before you go to
sleep. The sleep timer automatically switches the set to standby
after the preset time elapses.
Press the SLEEP button to select the number of minutes. The dis0 will appear on the screen, followed by 10, 20, 30, 60, 90,
play
120, 180 and 240. The timer begins to count down from the number
of minutes selected.
Note :
a.
To view the remaining sleep time, press the SLEEP button once.
b. To cancel the sleep time, repeatedly press the SLEEP button
until the display
0 appears.
c.
When you switch the set off, the set releases the preset sleep
time.
PIP
Option
PIP is
operation (option)
:
an
optional function,
so
that
only the
set with PIP function can
operate.
PIP
(Picture
in
Picture) displays
a
picture
within
a
picture.
On and off
Press the PIP button to switch on the sub
press this button again to switch it off.
Input
mode selection for sub
Press the INPUT button to select the
picture.
picture
input
Each time this button is pressed, each
displayed as shown below.
mode for the sub
input
picture.
mode for the sub
pic-
ture is
Programme
number
AV2
AV1
AV4
COMPONENT1
Swapping
PIP
Programme
exchange
selection for sub
AV3
(option)
between main and sub
Press the SWAP button to
PR-
PR+
SWAP
INPUT
pictures
the main and sub
pictures.
picture
Press the PR +/- buttons to select a programme for the sub picture.
The selected programme number is displayed just below the programme number of main picture.
Sub
picture
size
Repeatedly press the SIZE button to select the desired sub
size. The sub picture appears as below.
1/16 size of the main
picture
1/9 size
picture
1/2 size
Note : If broadcasting system of the main picture for PIP is differ
from sub picture's for PIP, the sub picture not be natural. (ex: In
case that main picture/sub picture is PAL/NTSC system)
Sub
picture
SCAN
STILL
SIZE
freeze
Press the STILL button to freeze motion of the sub
Press this button again to restore motion.
Sub
POSITION
picture.
picture position change
Press the POSITION button repeatedly until desired
achieved. The sub pictures move clockwise.
Programme
position
is
scan
This function enables you to search all the stored stations on 12
sub pictures and see your favorite station by exchanging the main
and sub pictures.
Press the SCAN button repeatedly to select 12 sub pictures.
The selected sub pictures search all the stored stations
Press the SCAN button again to switch off sub pictures.
.
21
Teletext
(option)
Teletext (or TOP text) is an optional function, therefore only
with the teletext system can receive the teletext broadcast.
a
set
free service broadcast by most TV stations which gives
information on news, weather, television programmes, share prices and many other topics.
Teletext is
a
up-to-the-minute
The teletext decoder of this TV can support the SIMPLE, TOP and
FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern
methods allowing quick and easy selection of teletext information.
POWER
I/II
TV/AV
TURBO
SOUND
PICTURE
Switch on/off
PIP
TEXT
PR-
PR+
INPUT
SWAP
MENU
VOL
INPUT
PR
MUTE
OK
Press the TEXT button to switch to teletext.
The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time are displayed
on the screen headline. The first page number indicates your selection, while the second shows the current page displayed.
Press the TEXT or TV/AV button to switch off teletext. The previous
mode reappears.
VOL
SIMPLE text
selection
Enter the desired page number as a three digit number with the
NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then reenter the correct page number.
The Δ / Ε button can be used to select the preceding or fol-
Page
1.
PR
1
2
3
4
5
6
7
8
9
PSM
0
SSM
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
M
LIST
2.
lowing page.
a colour button in LIST mode
If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the
M
button to switch to LIST mode.
Programming
?
Four teletext page numbers of your choice can be colour coded and
selected by pressing the corresponding coloured button on
easily
EYE
STOP
REW
P/STILL
PLAY
REC
FF
the remote control handset.
1.
Press
a
2.
Using
the NUMBER buttons, select the page you wish to pro-
3.
gramme.
Press the OK button. Then the selected page is stored as the
selected page number with blinking once. From now on, you
4.
22
coloured button.
can select this page with the same coloured button.
The three other coloured buttons are programmed in this way.
Teletext
TOP text
(option)
(option)
The user guide displays four fields-red, green, yellow and blue at
the bottom of the screen. The yellow field denotes the next group
and the blue field indicates the next block.
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the yellow button to proceed to the next group with automatic overflow to the next block.
3. With the green button you can proceed to the next existing
page with automatic overflow to the next group.
Alternatively the Δ button can be used.
4. The red button permits to return to previous selection.
Alternatively the Ε button can be used.
Direct page selection
Corresponding to the SIMPLE teletext mode, you can select a page
by entering it as a three digit number using the NUMBER buttons in
TOP mode.
PR
FASTEXT
The teletext pages are colour coded along the bottom of the screen
and are selected by pressing the corresponding coloured button.
selection
i
Press the
button to select the index page.
You can select the pages which are colour coded along the bottom line with the same coloured buttons.
Corresponding to the SIMPLE teletext mode, you can select a
page by entering its three digit page number with the NUMBER
buttons in FASTEXT mode.
The Δ / Ε button can be used to select the preceding or fol-
Page
1.
2.
3.
4.
PR
1
2
3
4
5
6
7
8
9
0
lowing page.
23
Teletext
Special
(option)
teletext functions
REVEAL
Press this button to
display concealed information, such as
puzzles.
again to remove the information from the
solutions of riddles
Press this button
or
display.
POWER
I/II
SIZE
TV/AV
Selects double
TURBO
SOUND
PICTURE
PIP
TEXT
PR-
Press this
PR+
SWAP
INPUT
MENU
page.
Press this button
again
half of the page.
the bottom half of the
to return to the normal
display.
INPUT
PR
MUTE
UPDATE
VOL
will appear at the top left hand
teletext page. The display
corner of the screen. When the updated page is available then
will change to the page number.
display
Press this button to view the updated teletext page.
Displays
VOL
height text.
enlarge the top
button again to enlarge
Press this button to
OK
the TV
picture
on
the
screen
while
waiting
for the
new
HOLD
the automatic page
Stops
PR
change
which will
occur
if
a
tele-
text page consists of 2 or more sub pages. The number of
1
2
3
4
5
6
sub pages and the sub page displayed is, usually, shown on
the screen below the time. When this button is pressed the
7
8
9
stop symbol is displayed
PSM
0
POSITION
2/12PIP
STILL
SIZE
TIME
REVEAL
MIX
SLEEP
SSM
M
LIST
at the
top left-hand
corner
of the
and the automatic page change is inhibited.
To continue press this button again.
screen
?
MIX
Displays
the teletext pages
superimposed
on
the TV
pic-
ture.
EYE
STOP
REW
P/STILL
PLAY
REC
FF
To switch the TV
Note
:
picture off press this button again.
When TV and text picture are displayed half and half
of the screen, MIX function is not available.
TIME
viewing a TV programme, press this button to display
the time at the top right hand corner of the screen. Press this
button again to remove the display. In the teletext mode,
When
press this button to select a sub page number. The sub page
number is displayed at the bottom of the screen. To hold or
the sub page, press the RED / GREEN, Δ / Ε
NUMBER buttons.
change
Press
24
again
to exit this function.
or
Connection of external
You
can
connect additional
equipment,
such
as
equipment
VCRs, camcorders
etc. to your set.
(R)-AUDIO-(L)
VIDEO
OUT
COMPONENT1 COMPONENT2
S-VIDEO
Here shown may be somewhat different from your set.
(480i)
(480p)
AV2
(L)
(L)
(R)
(R)
AUDIO
AV1
AUDIO
MONO
Y
PB
PB
PR
PR
VIDEO
Y
ANT IN
LL 75Ω
VIDEO
Manufactured under license from Dolby Laboratories.
"Dolby", "Pro Logic" and the double-D symbol are
trademarks of Dolby Laboratories.
DVD INPUT
Aerial socket
1.
VCR
Connect the RF out socket of the VCR to the aerial socket
on
the back of the set.
2.
Connect the aerial cable to the RF aerial in socket of the VCR.
3.
Store the VCR channel on a desired programme number using
the 'Manual programme tuning' section.
Select the programme number where the VCR channel is
4.
(R)-AUDIO-(L)
VIDEO
OUT
COMPONENT1 COMPONENT2
S-VIDEO
(480i)
AUDIO
AV1
(L)
(L)
(R)
(R)
AUDIO
MONO
VIDEO
ANTIN
L L75Ω
stored.
5.
(480p)
AV2
Y
Y
PB
PB
PR
PR
VIDEO
Manufactured under license from Dolby Laboratories.
Logic" and the double-D symbol are
trademarks of Dolby Laboratories.
"Dolby", "Pro
DVD INPUT
Press the PLAY button
on
the VCR.
VCR
Audio/Video in/out sockets
1.
(option)
Connect the audio/video out sockets of the VCR to audio/video
in sockets of the set and in sockets of the VCR to out sockets
of the set.
2.
3.
Press the TV/AV button to select AV 1, AV 2
Press the PLAY button on the VCR.
The VCR
You
playback picture appears
on
the
also record programmes received
tape via audio/video out sockets.
can
or
AV 3.
S-VIDEOL/MN
AUDIO
R
AV3
screen.
by
the TV
on
video
VCR
: If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO socket of the set.
Note
S-VIDEO
L/MON
AUDIO
R
IN3
PCINUT
VCR
25
Connection of external
Euro scart socket
(R)-AUDIO-(L)
VIDEO
1.
OUT
COMPONENT1 COMPONENT2
S-VIDEO
(480i)
(480p)
AV2
AUDIO
AV1
(L)
(L)
(R)
(R)
AUDIO
MONO
Y
VIDEO
AV4
ANT IN
L L75Ω
4
Y
PB
PB
PR
PR
Manufactured under license from Dolby Laboratories.
"Dolby", "Pro Logic" and the double-D symbol are
trademarks of Dolby Laboratories.
VIDEO
2.
DVD INPUT
VCR
equipment
(option)
Connect the Euro scart socket of the VCR to the Euro scart
socket of the set.
Press the PLAY button on the VCR.
If your VCR outputs a switching voltage connect to Euro scart
socket, the set will switch to AV 4 mode automatically. But if you
want to keep on watching TV mode, press the Δ / Ε or NUMBER buttons.
Otherwise press the TV/AV button
to select AV 4. The VCR
VIDEO
(R)-AUDIO-(L)
You
OUT
can
playback
the remote control handset
picture appears on the screen.
on
also record programmes received
by the TV on
video tape.
S-VIDEO
AV2
AV1
MONO
S-VIDEO VCR
Note : Signal type RGB, i.e. the signals red, green and blue can
only be selected for the Euro scart can be received. These signals
are transmitted, for example, by a pay TV decoder, game machine
or photo CD unit, etc.
S-Video / Audio in sockets
When
connecting
picture quality will
S-VIDEOL/MN
1.
2.
AUDIO
R
AV3
3.
4.
S-VIDEO VCR
(S-AV) (option)
an S-VIDEO VCR to the S-VIDEO socket, the
be further improved.
Connect the S-video socket of the VCR to the S-VIDEO socket
of the set.
Connect the audio cable from the S-VIDEO VCR to the AUDIO
sockets of the set.
Select AV1 or AV3 by pressing the TV/AV button repeatedly.
Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
Note : If both S-VIDEO and VIDEO sockets have been connected to
the S-VHS VCR simultaneously, only the S-VIDEO can be received.
S-VIDEO
Component
L/MON
Connect the COMPONENT DVD output sockets (Y Cb Cr, Y Pb Pr,
Y B-Y R-Y or Y PB PR) of the COMPONENT to the COMPONENT
1 (480i)/COMPONENT 2 (480p) sockets (Y PB PR) of the set.
2.
Connect the audio cable from the COMPONENT to COMPONENT 1 (480i)/COMPONENT 2 (480p) AUDIO sockets of the set.
Press the TV/AV button to select COMPONENT 1 or COMPONENT 2.
Press the PLAY button on the COMPONENT.
The COMPONENT playback picture appears on the screen.
R
IN3
3.
S-VIDEO VCR
4.
COMPONENT1 COMPONENT2
(480i)
(480p)
(L)
(L)
(R)
(R)
Y
Y
AUDIO
VIDEO
PB
PB
PR
PR
DVD INPUT
AUDIO
VIDEO
Note :
a.
Even when DVD video input can be output, you will have only
black and white picture, but DVD audio input cannot be output.
b. Only COMPONENT 2 (480p) can be received vertical Frequency
(60Hz) Progressive signal. If the picture is poor by connecting the
COMPONENT 2 (480p), connect the DVD to the COMPONENT
1
DVD
26
(option)
1.
AUDIO
PCINUT
in sockets
(480i).
Connection of external
PC
1.
Input
/ Audio in sockets
equipment
(option)
Connect the PC cable from the monitor output socket of the PC
to the PC INPUT sockets of the set.
2.
S-VIDEO
L/MON
Connect the audio cable from the PC to the AUDIO sockets of
AUDIO
R
IN3
the set.
3.
Switch
on
set can be
Note
a.
the PC, and the PC screen appears
operated as the PC monitor.
on
the set. The
PCINUT
PERSONAL COMPUTER
:
The cables
are
not
supplied,
such
as
the PC cable, audio cable
etc.
b.
Set the resolution of PC to VGA 640x480
(60 Hz)
video mode
to use this set as PC monitor.
Displayable
MODE
Monitor
Specification (only)
Resolution
Horizontal
Frequency(KHz)
VGA
31.5KHz
640x480
(Synchronization input
form
:
Vertical
Frequency(Hz)
60Hz
separate)
27
Troubleshooting
check list
Symptoms
No
picture,
no
sound
Sound OK, poor
picture
Picture OK, poor sound
Picture blurred
Lines
or
streaks in
Poor
picture
reception
on some
channels
No colour
Poor colour
Remote control does not work
Check these items and try to
adjust these
The mains plug-(plugged in and
switched on)
Is the TV switched
Try
on
another channel
(weak signal)
Check aerial
(plugged
Check aerial
(broken lead?)
into
TV?)
Check aerial
Check for local interference
Adjust
contrast
Adjust brightness
Adjust
colour
Adjust
volume
Check the batteries in remote control
Check Audio/Video sockets
(VCR only)