LG | FH2 | LG FH2 Owner’s Manual

OWNER’S MANUAL
HIGH POWER
SPEAKER
SYSTEM
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
FH2
*MFL70220792*
www.lg.com
Copyright © 2016-2017 LG Electronics. All Rights Reserved
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, should be placed on the
apparatus.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not use high voltage products around
this product. (ex. Electrical swatter) This product may
malfunction due to electrical shock.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
NOTICE: For safety marking information including
product identification and supply ratings, please refer
to the main label on the bottom or the other surface
of the product.
CAUTION concerning the Power Cord
The Power Plug is the disconnecting device. In case
of an emergency, the Power Plug must remain readily
accessible.
Check the specification page of this owner’s manual
to be certain of the current requirements.
Do not overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords, frayed
power cords, or damaged or cracked wire insulation
are dangerous. Any of these conditions could result
in electric shock or fire. Periodically examine the
cord of your device, and if its appearance indicates
damage or deterioration, unplug it, discontinue use of
the device, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord exits
the device.
Getting Started
3
CAUTION: The ventilation should not be impeded by
covering the ventilation openings with items, such as
newspapers, table-cloths, curtains, etc.
CAUTION: The apparatus could be used in tropical
and moderate climates.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the battery
from the equipment: Remove the old battery or
battery pack, follow the steps in reverse order than
the assembly. To prevent contamination of the
environment and bring on possible threat to human
and animal health, the old battery or the battery
put it in the appropriate container at designated
collection points. Do not dispose of batteries or
battery together with other waste. It is recommended
that you use local, free reimbursement systems
batteries and accumulators. The battery shall not be
exposed to excessive heat such as sunshine, fire or
the like.
CAUTION: No naked flame sources, such as lighted
candles, should be placed on the apparatus.
Symbols
~
Refers to alternating current(AC).
0
Refers to direct current(DC).
Refers to class II equipment.
1
Refers to stand-by.
!
Refers to “ON” (power).
Refers to dangerous voltage.
1
Getting Started
CAUTION: The MAINS plug or the appliance coupler
is used as the disconnect device, the disconnect
device shall remain readily operable.
4
Getting Started
Precautions on handling a
battery
1
Getting Started
yy This unit has a built-in valve regulated lead-acid
rechargeable battery. (12 V/7.0 Ah)
yy Do not use the battery in a closed room or near
fire.
yy Charge the battery under the charging condition
specified.
yy If any corrosion of the terminals, leakage or
deformation of the case of the battery is found, do
not use the battery.
yy If the battery leaks, while protecting your hands or
clothing, remove the battery from the device and
should be extremely careful not to infect the skin
or eyes.
yy If the battery leaks and the liquid inside spills on
the skin or clothing, immediately wash it off with
plenty of clean water.
If the liquid splashes into eyes, immediately flush
the eyes with plenty of clean water and consult a
doctor.
yy Avoid mixed usage of batteries differing in type,
manufacturer or history of use.
yy Do not throw the battery in fire nor heat the
battery.
yy Do not short of battery terminals.
yy Do not attempt to disassemble, remodel or
destroy the battery.
yy Do not place the battery near a child.
yy The battery can be replaced. If you need to charge
your battery more and more frequently, it might be
time to replace it. The battery should be serviced
by LG Electronics customer care center.
yy Charge fully before storing a battery which has
not been in use for a long period and turn ON/OFF
switch off (OFF). Store the battery in a cool, dry
place.
yy During storage of the battery, charge it at least
once every three months. If the battery is stored
for a long period without being charged, its battery
life may be shortened.
yy The used battery must be recycled or disposed of
separately from household waste.
Table of Contents
5
Table of Contents
1
Getting Started
3Operating
2
4
6
6
6
6
6
7
7
8
9
9
9
10
Safety Information
– Precautions on handling a battery
Unique Features
Playable file Requirement
– Music file requirement
– Compatible USB Devices
– USB device requirement
Top Panel
Rear Panel
Carrying the unit
How to Affix the Ferrite Core
– Affix the Ferrite Core for power cord
Power Connection
Charging Battery
12
12
13
13
2Connecting
11
11
11
Optional Equipment Connection
– PORT. IN Connection
– USB Connection
15
15
15
15
16
16
16
16
17
17
17
17
Basic Operations
– USB Operations
Using BLUETOOTH® wireless technology
– Listening to music stored on the Bluetooth
devices
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
Sound adjustment
– Setting the sound mode
Other Operations
– Using Microphone
– VOICE CANCELLER
– KEY CHANGER
– AUTO POWER On
– Auto function change
1
2
3
4
5
4Troubleshooting
18 Troubleshooting
18 – General
5Appendix
19
20
20
20
General specifications
Maintenance
– Handling the Unit
Trademarks and Licenses
6
1
Getting Started
Unique Features
Compatible USB Devices
Bluetooth®
yy USB Flash Drive :
Devices that support USB2.0 or USB1.1.
Getting Started
Listens to music stored on your Bluetooth device.
Portable In
Listens to music from your portable device. (MP3,
Notebook, etc.)
Carrying the unit
The unit has wheels and a handle so you can easily
move the unit.
Playable file
Requirement
Music file requirement
MP3/WMA file compatibility with this unit is limited
as follows.
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
yy Maximum files : 999
yy Maximum folders : 99
yy File extensions : “.mp3”/ “.wma”
yy Certain MP3/WMA files may not be played
depending on the type or format of the file.
yy MP3 Player : Flash type MP3 player.
yy The USB function of this unit does not support all
USB devices.
USB device requirement
yy Devices which require additional program
installation when you have connected it to a
computer, are not supported.
yy Do not extract the USB device while in operation.
yy For a large capacity USB, it may take longer than a
few minute to be searched.
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
yy Using NTFS file system is not supported. (Only
FAT(16/ 32) file system is supported.)
yy This unit recognizes up to 999 files.
yy External HDD, SSD, Card readers, Locked devices,
or hard type USB devices are not supported.
yy USB port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
yy Some USB may not work with this unit.
Getting Started
Top Panel
p onm
7
l
kT
Starts or pauses playback.
lFM antenna
a
k
mCHARGING
Battery charging indicator
nUSB port
You can play sound files by connecting the USB
device.
bcdef
g
h i j
aMASTER VOLUME
Adjusts speaker or microphone volume.
b1/! (Standby/On)
Switches the unit ON or OFF.
cMIC (Microphone)
Press to select a microphone’s volume control
mode.
oPORT.IN
Connects a portable device.
pMIC (Microphone)
Connects a microphone.
Rear Panel
d
(KEY CHANGER)
Changes the key to suit your vocal range.
eVOICE CANCELLER
You can enjoy the function while playing the
music, by reducing singer vocal of music in the
various source.
fSOUND EFFECT/BASS BLAST
- Chooses sound impressions.
- Press and hold to select BASS effect directly.
gDisplay window
hF (Function)
Selects the function and input source.
iY/U
- Skips Fast backward or Forward. /
Searches for a section within a file by pressing
and holding.
- Selects the radio stations.
a b
aPower ON/OFF switch
Switches the unit ON or OFF.
(Battery can be charged even when this unit is in
off (OFF) status.)
bAC in socket
1
Getting Started
jPRESET/REPEAT
- Chooses a preset number for a radio station. /
Stores radio stations by pressing and holding.
- Listens to your files repeatedly or randomly.
- Sees the name of connected all Bluetooth
device in Bluetooth mode.
8
Getting Started
Carrying the unit
1
The unit has wheels and a handle so you can easily
move the unit.
Getting Started
1. Press the lock button on the handle.
>>Caution
yy Do not shake the handle to hard. Otherwise it
may result in the unit will be damaged.
yy Do not hang heavy things on the handle.
Otherwise it may result in the unit will be
damaged.
yy Do not draw the unit on the unpaved road or
the stair.
yy Be careful it does not drop the unit when you
carry it.
yy Carry the unit, after then disconnect the
connected cables.
yy Do not step or sit on the unit. Otherwise
this unit may fall down and causing personal
injury.
2. Pull the handle up.
yy Do not place the unit on an unstable position
and place the unit at a safe distance from the
child’s reach.
yy Be careful that the unit should not fall down.
Otherwise it may result in malfunction and
causing personal injury and/ or property
damage.
yy Fix the handle when you use the unit.
3. Release the lock button to lock the handle in
place.
,,Note
To retract the handle, press the button and push
down.
Getting Started
How to Affix the Ferrite
Core
Power Connection
Connect this unit to the power supply with the
supplied AC power cord.
1. Connect the supplied AC power cord to this unit.
2. Plug the AC power cord into an AC outlet.
Affix the Ferrite Core for power
cord
You must affix a ferrite core in order to reduce or
eliminate electrical interference.
1. Open
AC power cord
2. Wind (Once)
3. Turn ON/OFF Switch on (ON).
,,Note
yy When you turn ON/OFF Switch on (ON), this
unit turns on even if this unit has been turned
off. If the battery level is very low, this unit
does not turn on even if you turn ON/OFF
switch on (ON).
3. Close
yy When the battery level is low, this unit
displays LOW BATTERY frequently. And if the
battery level becomes even lower, this unit
turns off automatically.
yy Previous setting may not be saved when you
turn ON/OFF switch off (OFF).
yy Previous setting may not be saved when the
unit’s power is shut off due to low battery.
1
Getting Started
Ferrite core may not be provided depending on each
nation’s regulations.
9
10 Getting Started
Charging Battery
This unit has a built-in battery.
1
Getting Started
-- By connecting AC power, battery will start
charging.
-- If Battery charging indicator is in red, this means
that battery is charging now.
-- If the battery charging indicator is in green,
this means that battery charging is completed.
For efficient performance of battery, it is
recommended fully charging the device until the
green LED goes off.
-- Charge battery for about 9 hours before you start
using this unit for the first time.
,,Note
yy Operating time is approx. 15 hours. (Based
on fully charging the battery and continuous
playback using 50 % volume level.) It may
vary depending on the battery status and
operational conditions.
yy If you are listening to the music while
charging, it will take longer to charge.
yy Charge the battery fully during the
recommended time after discharge.
Connecting 11
Optional Equipment
Connection
USB Connection
Connect a USB device (or MP3 player, etc.) to the
USB ports on the unit.
USB device
PORT. IN Connection
Connect an output (earphone or line out) of portable
device (MP3 or PMP etc) to the PORT. IN connector.
2
Connecting
Portable cable
,,Note
Removing the USB device from the unit :
1. Choose a different function.
2. Remove the USB device from the unit.
MP3 player etc.
Listening to music from your portable
player
The unit can be used to play the music from many
types of portable player.
1. Connect the portable player to the PORT. IN
connector of the unit.
2. Turn the power on by pressing 1/! on the unit.
3.Press F on the unit to select PORT (PORTABLE)
function.
4. Turn on the portable player and start it playing.
12 Operating
Basic Operations
USB Operations
1. Connect the USB device to the USB port.
2. Select USB function by pressing F on the unit.
To
Playback
3
Operating
Do this
Press T on the unit.
Press T on the unit during
Pause
playback.
Searching Press and hold Y/U on the unit
for a section during playback and release it at the
within a file point you want to listen to.
-- In pause status,
Press Y/U on the unit to go to
the next/previous file.
-- During Playback,
Skipping to Press U on the unit to go to the
the next/ next file.
previous file Playing less than 2 seconds, press
Y on the unit to go to the
previous file.
Playing after 3 seconds, press Y
on the unit to go to the beginning of
the file.
Press PRESET/REPEAT on the unit
Playing
repeatedly.
repeatedly or
OFF / ONE h / ALL h
randomly
/ SHUFFLE G
,,Note
yy Even after restarting the unit or switching
one function to another, you can listen to
music from the point where it’s last been
played.
yy The resume point may be cleared when in the
cases below
-- Removing the USB device from the unit.
>>Caution
yy Do not extract the USB device during
operation. (play, etc.)
yy Regular back up is recommended to prevent
data loss.
Operating 13
Using BLUETOOTH®
wireless technology
Listening to music stored on the
Bluetooth devices
About Bluetooth
Before you start the pairing procedure, make sure the
Bluetooth feature is activated on your Bluetooth
device. Refer to your Bluetooth device’s user guide.
Once a pairing operation is performed, it does not
need to be performed again.
Bluetooth is wireless communication technology for
short range connection.
The sound may be interrupted when the connection
interfered by the other electronic wave or you
connect the Bluetooth in the other rooms.
Bluetooth Profiles
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles. This
unit is compatible with following profile.
A2DP (Advanced Audio Distribution Profile)
Codec : SBC
1. Turn on the unit.
2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device display
depending on the type of Bluetooth device. Your
unit appears as “LG FH2(XX)”.
,,Note
yy XX means the last two digits of
Bluetooth address. For example, if your
unit has a Bluetooth address such as
9C:02:98:4A:F7:08, you will see “LG FH2(08)”
on your Bluetooth device.
yy Depending on the Bluetooth device type,
some devices may have a different pairing
process. Enter the PIN code (0000) as
needed.
yy You can connect this unit with up to 3
Bluetooth devices simultaneously using the
same method as described above, only in the
Bluetooth function.
yy The multi pairing connection is only supported
on Android or iOS devices. (Multi pairing
connection may not be supported depending
on the connected device specifications.)
yy Removable/detachable Bluetooth devices
(Ex: Dongle etc.) will not support multi pairing.
3. When this unit is successfully connected with
your Bluetooth device, “PAIRED” appears on the
display window and change to Bluetooth device
name soon.
3
Operating
Connecting individual devices under Bluetooth
wireless technology does not incur any charges. A
mobile phone with Bluetooth wireless technology
can be operated via the Cascade if the connection
was made via Bluetooth wireless technology.
Available Devices : Mobile phone, MP3, Laptop, PDA.
Pairing your unit and Bluetooth device
14 Operating
,,Note
yy "PAIRED" will momentarily appear on the
display when you connect other devices for
multi pairing.
yy If the device name is unavailable, “_” will be
displayed.
4. Listen to music.
To play a music stored on your Bluetooth device,
refer to your Bluetooth device’s user guide.
,,Note
3
Operating
yy When using Bluetooth® technology, you
have to make a connection between the unit
and the Bluetooth device as close as possible
and keep the distance.
However, it may not work well in certain
situations as described below :
-- There is a obstacle between the unit and
the Bluetooth device.
-- There is a device using same frequency
with Bluetooth® technology such as
a medical equipment, a microwave or a
wireless LAN device.
,,Note
yy When this unit connected with multiple
Bluetooth devices, only one device which
you are playing keeps Bluetooth connection
when you change the function to the others.
yy The sound may be interrupted when the
connection has interference from other
electronic devices.
yy You may not control the Bluetooth device
with this unit.
yy Depending on the type of the device, you may
not be able to use the Bluetooth function.
yy You can enjoy wireless system using phone,
MP3, Notebook, etc.
yy The more distance between the unit and the
Bluetooth device, the lower the sound quality
becomes.
yy Bluetooth connection will be disconnected
when the unit is turned off or the Bluetooth
device gets far from the unit.
yy When Bluetooth connection is disconnected,
connect the Bluetooth device to the unit
again.
yy You should connect your Bluetooth device to
this unit again when you restart it.
yy When a Bluetooth device is not connected,
“READY” appears on the display window.
yy Even if this unit connected up to 3 Bluetooth
devices in the Bluetooth mode, you can play
and control music by using only one of the
connected devices.
yy When you use the BT (Bluetooth) function,
adjust the volume to a proper level on the
Bluetooth device.
yy If it is not in the BT (Bluetooth) function, only
one device can be connected.
Operating 15
Radio Operations
Pull the FM antenna out and adjust the angle and
direction for better reception.
Listening to the radio
1.Press F on the unit until FM appears in the display
window.
The last received station is tuned in.
2. Auto tuning :
Press and hold Y/U on the unit for about
two seconds until the frequency indication starts
to change, then release. Scanning stops when the
unit tunes in a station.
Manual tuning :
Press Y/U on the unit repeatedly.
3. Adjust the volume by rotating MASTER VOLUME
on the unit.
Presetting the Radio Stations
You can preset 10 stations for FM.
Before tuning, make sure to turn down the volume.
1.Press F on the unit until FM appears in the display
window.
2. Select the desired frequency by pressing
Y/U on the unit.
3. Press and hold PRESET/REPEAT on the unit for
more than 2 seconds. A preset number will blink
in the display window.
4.Press Y/U on the unit to select the preset
number you want.
5.Press PRESET/REPEAT on the unit.
The station is stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen a preset station, press PRESET/REPEAT
on the unit.
1. Press and hold PRESET/REPEAT on the unit for
five seconds. “DEL ALL” will flash up on the unit
display.
-- If there is no saved radio stations, it displays
NONE.
2.Press PRESET/REPEAT on the unit to erase all
the saved radio stations.
3
Operating
Or
Deleting all the saved stations
16 Operating
Sound adjustment
Other Operations
Setting the sound mode
Using Microphone
This system has a number of pre-set surround sound
fields. The displayed items for the Equalizer may be
different depending on sound sources and effects.
1. Connect your microphone to the MIC jack.
You can select a desired sound mode by using
SOUND EFFECT/BASS BLAST on the unit.
On Display
3
BASS (BASS BLAST)
Operating
POP
CLASSIC
ROCK
JAZZ
STANDARD
,,Note
Description
Reinforces the treble,
bass and surround
sound effect.
This program lends
an enthusiastic
atmosphere to the
sound, giving you the
feeling you are at an
actual rock, pop, jazz or
classic concert.
You can enjoy
optimized sound.
By pressing and holding SOUND EFFECT/BASS
BLAST on the unit you can directly select BASS
effect.
2. Play the music you want.
3. Sing along with the accompaniment. Adjust
the microphone volume by pressing MIC and
rotating MASTER VOLUME clockwise or
counterclockwise on the unit.
,,Note
yy When not using the microphone, set the
MIC volume to minimum or turn off the MIC
and remove the microphone from the MIC
jack.
yy If the microphone is set too near the speaker,
a howling sound may be produced. In this case,
move the microphone away from the speaker
or decrease the sound level by pressing MIC
and rotating MASTER VOLUME.
yy If sound through the microphone is extremely
loud, it may be distorted. In this case, press MIC
and rotate MASTER VOLUME to minimum.
Operating 17
VOICE CANCELLER
AUTO POWER On
You can enjoy the function while playing the music, by
reducing singer vocal of music in the various source.
This unit automatically turns on by an input source :
Bluetooth
Press the VOICE CANCELLER , and “ON” will appear
in display window.
If you try to connect your Bluetooth device, this unit
turns on and connects your Bluetooth device. You
can play your music.
To cancel it, press VOICE CANCELLER again.
The quality of the VOICE CANCELLER may be
different depending on the recording conditions of
music files.
,,Note
yy This function is available USB or BT
(Bluetooth) Function.
yy If the function is not available, “NOT
SUPPORT” appears in the display window.
yy If a microphone is not connected, “INSERT
MIC” is scrolled in the display window.
yy It is not available on the MONO source.
yy To initialize it, change the Function or
disconnect the microphone.
yy This function may not be initialized depending
on the status of connected devices.
KEY CHANGER
You can adjust the key to 9 steps (4 steps higher, 4
steps lower and the original key).
yy To sharp the key one by one, press the
repeatedly during playback.
yy To flatten the key one by one, press the
repeatedly during playback.
,,Note
yy This function is available USB or BT
(Bluetooth) Function.
yy If a microphone is not connected, “INSERT
MIC” is scrolled in the display window.
yy To initialize it, change the Function, disconnect
the microphone or change the music.
yy This function may not be initialized depending
on the status of connected devices.
yy Depending on the connected device, the unit
turns on but Bluetooth function may not be
connected.
yy If you disconnect Bluetooth connection by
this unit, some Bluetooth devices try to
connect to the unit continually. Therefore it is
recommended to disconnect the connection
before turning off the unit.
yy If the ON/OFF switch on the rear panel is set
to off (OFF), AUTO POWER On cannot be
operated.
Auto function change
When you try to connect your Bluetooth device to
this unit, Bluetooth function is selected. Play your
music on the Bluetooth device.
Auto power down
This unit will turn itself off to save electricity in the
case were the main unit is not connected to an
external device and is fully charged.
3
Operating
yy This function is available to use only when a
microphone is connected.
,,Note
yy Depending on the connected device, this
function may not operate.
18 Troubleshooting
Troubleshooting
General
Problem
Cause & Solution
yy Turn off the power of this unit and the connected external device (Portable
player, etc.) and turn it on again.
The unit does not work
properly.
yy Disconnect the power cord of this unit and the connected external device
(Portable player, etc.) and then try connecting again.
yy Turn ON/OFF switch off (OFF) and on (ON).
yy The battery is discharged. Recharge the battery.
yy Check whether the ON/OFF switch is on (ON).
No Power.
4
No sound.
yy The power cord is not plugged in. Plug in the power cord.
yy Check whether electricity failed.
Check the condition by operating other electronic devices.
Troubleshooting
yy Check whether you select right function.
Press function button and check the selected function.
yy The antenna is positioned poorly.
Adjust the angle and direction for better reception.
Radio stations cannot be
tuned in properly.
yy The signal strength of the radio station is too weak.
Tune to the station manually.
yy No stations have been preset or preset stations have been cleared (when tuning
by scanning preset channels).
Preset some radio stations, see page 15 for details.
Appendix 19
General specifications
General
Power requirements
Refer to the main label on the unit.
Power consumption
Refer to the main label on the unit.
Dimensions (W x H x D)
Approx. 352.5 mm x 419.6 mm x 269.2 mm
Net Weight
Approx. 9.71 kg
Operating temperature
5 °C to 45 °C
Operating humidity
5 % to 60 %
Maximum operating altitude
2000 m
Inputs
Portable in (PORT. IN)
2.0 Vrms (3.5 mm stereo jack) x 1
Microphone (MIC)
Sensitivity 30 mV (1 kHz), 6.3 mm jack x 1
Tuner
FM Tuning Range
87,5 to 108.0 MHz or 87,50 to 108,00 MHz
System
Frequency Response
40 to 20,000 Hz
5
Signal-to-noise ratio
More than 75 dB
Dynamic range
More than 80 dB
Bus Power Supply (USB)
5 V 0 500 mA
Appendix
Amplifier (RMS Output power)
Total output
50 W (4 Ω at 1 kHz, 10 % THD)
Battery
Battery type
12 V/7.0 Ah (Valve Regulated Lead-Acid rechargeable battery)
Operating time
Approx. 15 hours (Based on fully charging the battery and continuous
playback using 50 % volume level.)
It may vary depending on the battery status and operational
conditions.
Charging time
Approx. 9 hours
It may vary depending on the battery status and operational
conditions.
yy Design and specifications are subject to change without notice.
20 Appendix
Maintenance
Trademarks and
Licenses
Handling the Unit
When shipping the unit
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally
packed at the factory.
Keeping the exterior surfaces clean
Do not use volatile liquids such as insecticide spray
near the unit. Wiping with strong pressure may
damage the surface. Do not leave rubber or plastic
products in contact with the unit for a long period of
time.
Cleaning the unit
5
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not use
strong solvents such as alcohol, benzine, or thinner,
as these might damage the surface of the unit.
The Bluetooth® word mark and logos are owned by
the Bluetooth® SIG, Inc. and any use of such marks
by LG Electronics is under license.
Other trademarks and trade names are those of their
respective owners.
Appendix
Download PDF

advertising