LG | HB954TB | LG HB954TB Owner’s Manual

HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 1
HB954TB (HB954TB-AD / SB94TB-C/F/S/W)
As an ENERGY STAR® Partner, LG
has determined that this product
or product models meet the
ENERGY STAR® guidelines for
energy efficiency.
ENERGY STAR® is a U.S. registered mark.
P/NO : MFL62426445
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC
SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer's
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing the
product on a bed, sofa, rug or other similar surface.
This product shall not be placed in a built-in installation such as a bookcase or rack unless
2
Page 2
proper ventilation is provided or the manufacturer's
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance, contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
CAUTION concerning the Power Cord
Most appliances recommend they be placed
upon a dedicated circuit;
That is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch
circuits. Check the specification page of this
owner's manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point
where the cord exits the appliance. To disconnect
power from the mains, pull out the mains cord plug.
When installing the product, ensure that the plug is
easily accessible.
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 3
Notes on Copyrights
Because AACS (Advanced Access Content
System) is approved as content protection
system for BD format, similar to use of CSS
(Content Scramble System) for DVD format,
certain restrictions are imposed on playback,
analog signal output, etc., of AACS protected
contents. The operation of this product and
restrictions on this product may vary depending
on your time of purchase as those restrictions
may be adopted and/or changed by AACS after
the production of this product.
Furthermore, BD-ROM Mark and BD+ are
additionally used as content protection systems
for BD format, which imposes certain restrictions
including playback restrictions for BD-ROM Mark
and/or BD+ protected contents. To obtain
additional information on AACS, BD-ROM Mark,
BD+, or this product, please contact an
authorized Customer Service Center.
Many BD-ROM/DVD discs are encoded with
copy protection. Because of this, you should only
connect your player directly to your TV, not to a
VCR. Connecting to a VCR results in a distorted
picture from copy-protected discs.
This product incorporates copyright protection
technologies that are protected by certain U.S.
patents and other intellectual property rights
owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation and is intended for home and other
limited viewing uses only, unless otherwise
authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, BD-ROM discs, DVDs,
CDs and other materials may subject you to civil
and/or criminal liability.
To use BD-Live functionality
You must attach an external USB device using the
USB port (see page 20).
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
What is SIMPLINK?
Some functions of this unit are controlled by the
TV’s remote control when this unit and LG TV’s with
SIMPLINK are connected through HDMI
connection.
Controllable functions by LG TV’s remote control;
Play, Pause, Scan, Skip, Stop, Power Off, etc.
Refer to the TV owner’s manual for the details of
SIMPLINK function.
LG TV’s with SIMPLINK function have the logo
as shown above.
Notes:
Depending on the disc type or playing status,
some SIMPLINK operation may differ from your
purpose or not work.
If “SIMPLINK” function does not work, check that
your HDMI cable supports by CEC (Consumer
Electronics Control) for HDMI.
If the sound is output from both the system’s
speakers and TV speaker or not output from both
them during SIMPLINK operation, reset speaker
setting of LG TV’s SIMPLINK menu.
Licenses
Java and all Java-based trademarks and logos are
trademarks or registered trademarks of Sun
Microsystems, Inc. in the United States and other
countries.
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #’s:
5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,392,195; 7,272,567;
7,333,929; 7,212,872 & other U.S. and worldwide
patents issued & pending. DTS is a registered
trademark and the DTS logos, Symbol, DTS-HD
and DTS-HD Master Audio I Essential are
trademarks of DTS, Inc. © 1996-2008 DTS, Inc. All
Rights Reserved.
“BD-LIVE” logo is trademark of Blu-ray Disc
association.
“DVD Logo” is trademark of DVD Format/Logo
Licensing Corporation.
“x.v.Colour” is a trademark of Sony Corporation.
“Blu-ray Disc” is a trademark.
“BONUSVIEW” is trademark of Blu-ray Disc
Association.
This product is licensed under the AVC patent portfolio license and VC-1 patent portfolio license for
the personal and non-commercial use of a consumer to (i) encode video in compliance with the
AVC Standard and VC-1 Standard (“AVC/VC-1
Video”) and/or (ii) decode AVC/VC-1 Video that was
encoded by a consumer engaged in a personal and
non-commercial activity and/or was obtained from a
video provider licensed to provide AVC/VC-1 Video.
No license is granted or shall be implied for any
other use. Additional information may be obtained
from MPEG LA, LLC. See http://www.mpegla.com.
“AVCHD” and the AVCHD logo are trademarks
of Panasonic and Sony Corporation.
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
iPhone is a trademark of Apple Inc.
YouTube is a trademark of Google Inc.
“Made for iPod” means that an electronic
accessory has been designed to connect
specifically to iPod and has been certified by the
developer to meet Apple performance standards.
“Works with iPhone” means that an electronic
accessory has been designed to connect
specifically to iPhone and has been certified by
the developer to meet Apple performance
standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
3
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 4
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
Viewing a photo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36-37
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Playing YouTube videos . . . . . . . . . . . . . . . . . . . . . . . . . .38-40
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Playing the iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41-42
Assembling the speakers . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Listening to music from your portable audio player . . . . . .43
Speaker connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-13
Listening to the sound from your component . . . . . . . . . . .43
Positioning the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Using HDMI IN jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Connections to your TV . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
Using DIGITAL AUDIO IN jacks . . . . . . . . . . . . . . . . . . . . . . .44
Resolution Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-17
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Internet connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-19
Language Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Setting the sound mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Adjust the speaker level settings . . . . . . . . . . . . . . . . . . . . .19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47-48
Using the late night function . . . . . . . . . . . . . . . . . . . . . . . . .19
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Open source software notice . . . . . . . . . . . . . . . . . . . . . . . .50
Using USB devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Using the Home Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Adjust the Setup settings . . . . . . . . . . . . . . . . . . . . . . . . .21-27
Play a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28-30
Displaying disc Information . . . . . . . . . . . . . . . . . . . . . . . . . .31
Enjoying BD-LIVE™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-33
Playing a movie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33-34
Listening to a music . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35-36
Before connecting, operating or adjusting this product,
please read this instruction booklet carefully and completely.
4
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 5
Introduction
To ensure proper use of this product, please read this owner’s manual
carefully and retain for future reference.
This manual provides information on the operation and maintenance of
your player. Should the unit require service, contact an authorized service
location.
About the
Symbol Display
“
“ may appear on your TV display during operation and indicates that
the function explained in this owner’s manual is not available on that specific media.
Symbols Used in this Manual
Note:
Indicates special notes and operating features.
Tip:
Indicates tips and hints for making the task easier.
A section whose title has one of the following symbols are applicable only
to the disc represented by the symbol.
ALL
BD
All discs listed below
BD-ROM disc
DVD
DVD-Video, DVD±R/RW in Video mode or VR
mode and finalized
AVCHD
DVD±R/RW in AVCHD format
DivX
DivX files
ACD
Audio CDs
MP3
MP3 files
WMA
WMA files
Handling the Unit
When shipping the unit
Please save the original shipping carton and packing materials. If you need
to ship the unit, for maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
Do not use volatile liquids such as insecticide spray near the unit.
Wiping with strong pressure may damage the surface.
Do not leave rubber or plastic products in contact with the unit for a long
period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent solution.
Do not use strong solvents such as alcohol, benzine, or thinner, as these
might damage the surface of the unit.
Maintaining the Unit
The unit is a high-tech, precision device. If the optical pick-up lens and disc
drive parts are dirty or worn, the picture quality could be diminished.
For details, please contact your nearest authorized service center.
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold the disc by the edges so
that fingerprints do not get on the surface. Never stick paper or tape on the
disc.
Storing Discs
After playing, store the disc in its case. Do not expose the disc to direct
sunlight or sources of heat and never leave it in a parked car exposed to
direct sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor picture quality and sound
distortion. Before playing, clean the disc with a clean cloth. Wipe the disc
from the center out.
Do not use strong solvents such as alcohol, benzine, thinner, commercially
available cleaners, or anti-static spray intended for older vinyl records.
5
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 6
Playable Discs
Blu-ray Disc
- Discs such as movies that can be purchased or rented
- BD-R/RE discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be purchased or rented
DVD-R (8 cm / 12 cm disc)
- Video mode and finalized only
- Supports the dual layer disc also
- AVCHD format
- DVD-R discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
DVD-RW (8 cm / 12 cm disc)
- VR mode, Video mode and finalized only
- AVCHD format
- DVD-RW discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
Notes:
Depending on the conditions of the recording equipment or the CDR/RW (or DVD±R/RW) disc itself, some CD-R/RW (or DVD±R/RW) discs
cannot be played on the unit.
Do not attach any seal or label to either side (the labeled side or the
recorded side) of a disc.
Do not use irregularly shaped CDs (e.g., heart-shaped or octagonal).
Doing so may result in malfunctions.
Depending on the recording software & the finalization, some recorded
discs (CD-R/RW or DVD±R/RW) may not be playable.
DVD±R/RW and CD-R/RW discs recorded using a personal computer or
a DVD or CD Recorder may not play if the disc is damaged or dirty, or if
there is dirt or condensation on the player’s lens.
If you record a disc using a personal computer, even if it is recorded in a
compatible format, there are cases in which it may not play because of
the settings of the application software used to create the disc. (Check
with the software publisher for more detailed information.)
This player requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality. Pre-recorded DVDs
are automatically set to these standards. There are many different types
of recordable disc formats (including CD-R containing MP3 or WMA
files) and these require certain pre-existing conditions to ensure compatible playback.
Customers should note that permission is required in order to download
MP3 / WMA files and music from the Internet. Our company has no right
to grant such permission. Permission should always be sought from the
copyright owner.
You have to set the disc format option to [Mastered] in order to make the
discs compatible with the LG players when formatting rewritable discs.
When setting the option to Live System, you cannot use it on LG player.
(Mastered/Live File System : Disc format system for windows Vista)
DVD+R (8 cm / 12 cm disc)
- Finalized disc only
- Supports the dual layer disc also
- AVCHD format
- DVD+R discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
DVD+RW (8 cm / 12 cm disc)
- Video mode and finalized only
- AVCHD format
- DVD+RW discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
Audio CD (8 cm / 12 cm disc)
Audio CDs or CD-Rs/CD-RWs in audio CD format that can be
purchased
CD-R/CD-RW (8 cm / 12 cm disc)
CD-R/CD-RW discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
6
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 7
BD-ROM Disc Features
BD-ROM Discs can store 25 GB (single layer) or 50 GB (dual layer) on a
single sided disc - about 5 to 10 times the capacity of a DVD.
BD-ROM Discs also support the highest quality HD video available in the
industry (up to 1920 x 1080) - Large capacity means no compromise on
video quality. Furthermore, a BD-ROM disc has the same familiar size and
look as DVD.
The following BD-ROM disc features are disc dependent and will vary.
Appearance and navigation of features will also vary from disc to disc.
Not all discs will have the features described below.
BD-ROM, Hybrid disc have both BD-ROM and DVD (or CD) layers on one
side. On such discs, BD-ROM layer will be only played back in this player.
Video highlights
The BD-ROM format for movie distribution supports three highly advanced
video codecs, including MPEG-2, MPEG4 AVC (H.264), and SMPTE VC1.
HD video resolutions are also available:
1920 x 1080 HD
1280 x 720 HD
Graphic planes
Two individual, full HD resolution (1920x1080) graphic planes (layers) are
available, on top of the HD video layer. One plane is assigned to videorelated, frame accurate graphics (like subtitles), and the other plane is
assigned to interactive graphic elements, such as buttons or menus.
For both planes, various wipes, fades and scroll effects may be available.
For High-Definition Playback
To view high-definition contents from BD-ROM discs, an HDTV is required.
Some discs may require HDMI OUT for viewing of high-definition contents.
Ability to view high-definition contents in BD-ROM discs may be limited
depending on the resolution of your TV.
Menu sounds
When you highlight or select a menu option, sounds can be heard such as
button clicks or a voice-over explaining the highlighted menu choice.
Multi-page/PopUp Menus
With DVD-Video, playback is interrupted each time a new menu screen is
accessed. Due to BD-ROM disc’s ability to preload data from the disc without interrupting playback, a menu can consist of several pages.
You can browse through the menu pages or select different menu paths,
while the audio and video remain playing in the background.
Interactivity
Certain BD-ROM Discs may contain animated menus and/or trivia games.
User Browsable Slideshows
With BD-ROM Discs, you can browse through various still pictures while
the audio remains playing.
Subtitles
Depending on what is contained on the BD-ROM disc, you may be able to
select different font styles, sizes and colours for some subtitles. Subtitles
may also be animated, scrolled or faded in and out.
BD-J Interactive Capability
The BD-ROM format supports Java for interactive functions. “BD-J” offers
content providers almost unlimited functionality when creating interactive
BD-ROM titles.
BD-ROM Disc Compatibility
This player supports BD-ROM Profile 2.
• Discs supporting BD-Live (BD-ROM version 2 Profile 2) that allows interactive functions to be used when this unit is connected to the Internet in
addition to the BONUSVIEW function.
• Discs supporting BONUSVIEW (BD-ROM version 2 Profile 1 version
1.1/Final Standard Profile) that allows Virtual packages or Picture-inPicture functions to be used.
7
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 8
Regional Code
Certain System Requirements
This unit has a regional code printed on the rear of the unit. This unit can play
only BD-ROM or DVD discs labeled same as the rear of the unit or “ALL”.
For high definition video playback:
AVCHD (Advanced Video Codec High Definition)
• This player can playback AVCHD format discs. These discs are normally
recorded and used in camcorders.
• The AVCHD format is a high definition digital video camera format.
• The MPEG-4 AVC/H.264 format is capable of compressing images at higher
efficiency than that of the conventional image compressing format.
• Some AVCHD discs use the “x.v.Colour” format.
• This player can playback AVCHD discs using “x.v.Colour” format.
• “x.v.Colour” is a trademark of Sony Corporation.
• Some AVCHD format discs may not play, depending on the recording condition.
• AVCHD format discs need to be finalized.
• “x.v.Colour” offers a wider colour range than normal DVD camcorder discs.
Compatibility Notes
• Because BD-ROM are a new format, certain disc, digital connection and
other compatibility issues are possible. If you experience compatibility problems, please contact an authorized Customer Service Center.
• Viewing high-definition content and up-converting standard DVD content may
require a HDMI-capable input or HDCP-capable DVI input on your display
device.
• Some BD-ROM and DVD discs may restrict the use of some operation
commands or features.
• Dolby Digital EX, DTS-ES and DTS 96/24 are output as Dolby Digital 5.1 or
DTS 5.1.
• You can use the USB device that is used to store some disc related
information, including downloaded on-line content. The disc you are using will
control how long this information is retained.
8
• High definition display that has COMPONENT or HDMI input jacks.
• BD-ROM disc with high definition content.
• HDMI or HDCP capable DVI input on your display device is required for
some content (as specified by disc authors).
• For up-conversion of standard definition DVD, a HDMI or HDCP capable DVI
input on your display device is required for copy protected content.
Important Notice for TV colour system
The colour system of this player differs according to currently playing discs or
video contents (YouTube, etc.).
For example, when the player plays back the disc recorded in the NTSC colour
system, the image is outputted as a NTSC signal.
Only the multi system colour TV can receive all signals outputted from the
player.
Notes:
• If you have a PAL colour system TV, you will see just distorted images when
using discs recorded in NTSC.
• The multi system colour TV changes the colour system automatically
according to input signals. In case that the colour system is not changed
automatically, turn it off and then on to see normal images on screen.
• Even if the disc and video contents (YouTube, etc.) recorded in NTSC colour
system are well displayed on your TV, these may not be recorded correctly
on your recorder.
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 9
Remote control
POWER
a
a INPUT (TUNER): Changes the input source
(FM, AM, AUX, PORTABLE, OPTICAL, COAXIAL,
HDMI IN 1, HDMI IN 2)
NIGHT (
): Sets the late night function.
d OPEN/CLOSE (Z): Opens and closes the disc tray.
iPod: Selects REMOTE IPOD or OSD IPOD mode.
SUBTITLE (
): Selects a subtitle language.
DISPLAY: Displays or exits On-Screen Display.
HOME: Displays or exits the [Home Menu].
REPEAT: Repeat a desired section.
DISC MENU: Accesses menu on a disc.
b CLEAR: Removes a mark on the search menu or a
number when setting the password.
Coloured (A, B, C, D) buttons: Use to navigate BDROM menus. They are also used for [MOVIE], [PHOTO],
[MUSIC] and [YouTube] menu.
Direction buttons: Selects an option in the menu.
PRESET (v/V): Selects programme of Radio.
TUN. (+/-): Tunes in the desired radio station.
ENTER ( ): Acknowledges menu selection.
- D button: Selects MONO or STEREO in FM mode.
RETURN (O): Exits the menu or resumes playback.
The resume play function may work depending on the
BD-ROM disc.
SLEEP: Sets a certain period of time after which the unit
will switch to standby.
TITLE/POPUP: Displays the DVD title menu or
BD-ROM’s popup menu, if available.
c TV Control Buttons: See page 45.
PLAY (N): Starts playback.
* Depending on a disc type or the pre-recorded contents of the BD-ROM disc, different functions may be
executed than other media or there are no response
when pressing some buttons (depending on media
used).
PAUSE/STEP (X): Pauses playback.
Remote Control Operation
SKIP (. / >): Go to next or previous chapter /
track / file.
Point the Remote Control at the remote sensor and
press the buttons.
SCAN (m / M): Searches backward or forward.
Remote Control Battery Installation
Remove the battery cover on the rear of the Remote
Control, and insert a R03 (size AAA) battery with
and
matched correctly.
STOP (x): Stops playback.
d
RESOLUTION: Sets the output resolution for HDMI and
COMPONENT VIDEO OUT jacks.
MARKER: Marks any point during playback.
SEARCH: Displays or exits the search menu.
PIP*: Switches on/off Secondary Video (Picture-in-picture) (BD-ROM only).
c
0-9 numerical buttons: Select numbered options in a
menu.
POWER: Switches the player ON or OFF.
b
VOL. (+/-): Adjusts speaker volume.
SPK LEVEL (
SOUND (
): Sets the sound level of desired speaker.
): Selects a sound mode.
MUTE: Press MUTE to mute your unit. You can mute
your unit in order, for example, to answer the telephone.
9
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 10
Front panel
a
b
c
d
e
f
g
a 1/}} (POWER) Button
Switches the unit ON or OFF.
b Disc Tray
Insert a disc here.
c iPOD Dock
Connect your iPod here.
Push Z to open the iPod Dock.
d Remote Sensor
Point the remote control here.
e Touch Buttons
- Z (OPEN/CLOSE)
Opens or closes the disc tray.
- (N/X)PLAY / PAUSE
Starts playback.
Pause playback temporarily,
press again to exit pause mode.
- x (STOP)
Stops playback.
- . / > (SKIP)
Go to next or previous file/track/chapter.
Searches backward or forward if you press and hold it.
10
h
- FUNC.
Changes the input source (FM, AM, OSD IPOD, REMOTE IPOD,
AUX, PORTABLE, OPTICAL, COAXIAL, HDMI IN 1, HDMI IN 2) or
displays On-Screen Display.
f USB Port
Connect a USB device.
g Display Window
Shows the current status of the player.
h VOLUME
Adjusts speaker volume.
Precautions in using the touch buttons
• Use the touch buttons with clean and dry hands.
- In a humid environment, wipe out any moisture on the touch buttons
before using.
• Do not press the touch buttons hard to make it work.
- If you apply too much strength, it can damage the sensor of the touch
buttons.
• Touch the button that you want to work in order to operate the function
correctly.
• Be careful not to have any conductive material such as metallic object
on the touch buttons. It can cause malfunctions.
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 11
Rear panel
a
b
c
d e
h ij
f
g
k
l
m
n
a AC Power Cord
Plug into the power source.
i DIGITAL AUDIO IN (OPTICAL)
Connect to digital (optical) audio equipment.
b SPEAKER Connectors
Connect the speakers.
j PORT. IN
Connect to a portable player with audio outputs.
c Cooling Fan
k COMPONENT VIDEO (Y PB PR)
OUTPUT (PROGRESSIVE SCAN)
Connect to a TV with Y Pb Pr inputs.
d FM ANTENNA Connector
Connect the FM antenna.
e DIGITAL AUDIO IN (COAXIAL)
Connect to digital (coaxial) audio equipment.
f VIDEO OUT
Connect to a TV with video inputs.
g AUX (L/R) INPUT
Connect to an external source with 2 channel audio outputs.
l LAN port
Connect a network with an always-on broadband connection.
m HDMI IN (Type A) 1/2
Connect to an external source with HDMI outputs.
n HDMI OUT (Type A)
Connect to TV with HDMI inputs. (Interface for digital audio and video)
h AM ANTENNA Connector
Connect the AM antenna.
11
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 12
Assembling the Speakers
Speaker Connection
Before connecting the speakers, assemble the speakers.
Attaching the speakers to the player
a
Fix the post to the base by rotating the post.
a
Each one is colour-coded by a band near each end and connects one of
the six speakers to the player.
b
b
c
You will have received six speaker cables.
Connect the wires to the player.
Match each wire’s coloured band to the same coloured connection
terminal on the rear of the player. To connect the cable to the player,
press each plastic finger pad to open the connection terminal. Insert the
wire and release the finger pad.
Draw the connector cable through the hole on the stand.
Fix the speaker to the stand by rotating the speaker.
Connect the black end of each wire to
the terminals marked -(minus) and the
other end to the terminals marked +
(plus).
Connect the connector cable between the speaker and base.
c
Connect the wires to the speakers.
Connect the other end of each wire to the correct speaker according to
the colour coding:
d
12
Connect the speaker cables to the speaker.
Use the speaker cable of the red and white tube. Connect the black
end of each wire to the terminal marked - (minus) and the other end to
the terminal marked + (plus).
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 13
COLOUR
SPEAKER
POSITION
Grey
Rear
Behind you and to your right.
Blue
Rear
Behind you and to your left.
Green
Center
Above or below screen, directly in front
of you.
Orange
Sub Woofer
This can be placed in any front
position.
Red
Front
In front of you, to the right of
the screen.
White
Front
In front of you, to the left of
the screen.
To connect the cable to the speakers, press each plastic finger pad to open the
connection terminals on the base of each speaker. Insert the wire and release
the finger pad.
Be careful of the following
Be careful to make sure children not to put their hands or any objects into the
*speaker duct.
*Speaker duct: A hall for plentiful bass sound on speaker cabinet(enclosure).
Positioning the System
The following illustration shows an example of positioning the system.
Note that the illustrations in these instructions differ from the actual unit for
explanation purposes.
For the best possible surround sound, all the speakers other than the
subwoofer should be placed at the same distance from the listening
position (A).
A Front left speaker (L)/ B Front right speaker (R):
Place the front speakers to the sides of the monitor or screen and as
flush with the screen surface as possible.
C Center speaker: Place the center speaker above or below the monitor
or screen.
D Surround left speaker (L)/ E Surround right speaker (R):
Place these speakers behind your listening position, facing slightly
inwards.
F Subwoofer: The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better to place the
subwoofer near the front speakers. Turn it slightly toward the center of
the room to reduce the wall reflections.
G Unit
FM/AM Antenna connection
AM - Connect the AM loop antenna to the player.
FM - Connect the FM antenna to the player.
The reception will be its best when the two loose ends of the antenna are in a
straight and horizontal line.
B
C
A
G
F
A
A
A
A
D
E
A
13
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 14
Connections to Your TV
Set the TV’s source to HDMI (refer to TV’s Owner’s manual).
Make one of the following connections, depending on the capabilities of
your existing equipment.
Notes:
Tips:
• Depending on your TV and other equipment you wish to connect, there
are various ways you could connect the player. Use only one of the
connections described below.
• Please refer to the manuals of your TV or other devices as necessary to
make the best connections.
Cautions:
• Make sure the player is connected directly to the TV. Tune the TV to the
correct video input channel.
• Do not connect your player via your VCR. The image could be distorted
by the copy protection system.
If you have a HDMI TV or monitor, you can connect it to this player using a
HDMI cable.
Connect the HDMI OUT jack on the player to the HDMI IN jack on a HDMI
compatible TV or monitor (H).
BD player
H
14
Tips:
• You can fully enjoy digital audio and video signals together with this
HDMI connection.
• When you use HDMI connection, you can change the resolution for the
HDMI output. (Refer to “Resolution Setting” on page 16-17.)
• Select the type of video output from the HDMI OUT jack using
[HDMI Color Setting] option on the [Setup] menu (see page 22).
Cautions:
HDMI Connection
TV
• You must select a HDMI audio output that your TV accepts using
[HDMI Audio] options on the [Setup] menu (see page 24).
• If a connected HDMI device does not accept the audio output of the unit,
the HDMI device’s audio sound may be distorted or may not output.
• Changing the resolution when the connection has already been
established may result in malfunctions. To solve the problem, turn
off the player and then turn it on again.
• When the HDMI connection with HDCP is not verified, TV screen is
changed to black or green screen or the snow noise may occur on the
screen. In this case, check the the HDMI connection, or disconnect the
HDMI cable.
• If there is noise or lines on the screen, please check the HDMI cable
(length is generally limited to 4.5m) and use a High Speed HDMI cable
(Version 1.3).
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 15
Additional Information for HDMI
Tip:
• When you connect a HDMI or DVI compatible device make sure of the
following:
- Try switching off the HDMI/DVI device and this player. Next, switch on
the HDMI/DVI device and leave it for around 30 seconds, then switch
on this player.
- The connected device’s video input is set correctly for this unit.
- The connected device is compatible with 720x576p, 1280x720p,
1920x1080i or 1920x1080p video input.
When you use COMPONENT VIDEO OUT connection, you can change
the resolution for the output. (Refer to “Resolution setting” on page 16-17.)
Video Connection
Connect the VIDEO OUT jack on the player to the video in jack on the TV
using a video cable (V).
You can hear the sound through the system’s speakers.
• Not all HDCP-compatible HDMI or DVI devices will work with this player.
- The picture will not be displayed properly with non-HDCP device.
- This player does not playback and TV screen is changed to black or
green screen or the snow noise may occur on the screen.
Component Video Connection
Connect the COMPONENT VIDEO OUT jacks on the player to the
corresponding input jacks on the TV using Y Pb Pr cables (C).
You can hear the sound through the system’s speakers.
BD player
V
TV
BD player
C
TV
15
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 16
Resolution Setting
The player provides several output resolutions for HDMI OUT and
COMPONENT VIDEO OUT jacks.
You can change the resolution using [Setup] menu or pressing the
RESOLUTION button in [Home Menu] and [Setup] Menu.
Available resolution according to the resolution setting
• When the non-copy protected media is playing back
Video Output
HDMI OUT
Note:
Since several factors affect the resolution of video output, see “Available
resolution according to the resolution setting” to the right.
How to change the resolution using RESOLUTION
button
Press RESOLUTION repeatedly in [Home Menu] and [Setup] Menu to
change the resolution. The display window will show you the current
resolution.
576i
576p
576p
576p
720p
720p
second level.
4 Use v / V to select the [Resolution] option then press B to move to the
third level.
5 Use v / V to select the desired resolution then press ENTER to confirm
576i
576i
576p
720p
1080i
1080i
1080p / 24Hz
1080p / 24Hz
576i
1080i
1080p / 50Hz
1080p / 50Hz
576i
1080i
1080i
• When the copy protected media is playing back
How to change the resolution using the [Setup] menu
1 Press HOME and the [Home Menu] appears.
2 Select the [Setup] and press ENTER. The [Setup] menu appears.
3 Use v / V to select [DISPLAY] option then press B to move to the
COMPONENT VIDEO OUT
HDMI connected HDMI disconnected
Resolution Setting
Video Output
HDMI OUT
COMPONENT VIDEO OUT
HDMI connected HDMI disconnected
Resolution Setting
576i
576p
576p
576p
576i
576i
720p
720p
576i
576p
1080i
1080i
576i
576p
1080p / 24Hz
1080p / 24Hz
576i
576p
1080p / 50Hz
1080p / 50Hz
576i
576p
576p
your selection.
Note:
If the video signal from the HDMI OUT jack is not output from the TV
screen when [Resolution] is set to [Auto], change the video output
resolution by pressing RESOLUTION button.
Notes:
• Depending on your display, some of the resolution settings may result in
the picture disappearing or an abnormal picture appearing. In this case,
press HOME then RESOLUTION repeatedly until the picture re-appear.
• This player supports simultaneous output of all video out jacks. The
resolution of the HDMI output will not be the same as the resolution
output on the component video output.
16
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 17
HDMI OUT connection
• For the 576i resolution setting, real output resolution of HDMI OUT will
change to 576p.
• If you select a resolution manually and then connect the HDMI jack to
TV and your TV does not accept it, the resolution setting is set to [Auto].
• If you select a resolution that your TV does not accept, the warning
message will appear. After resolution change, if you cannot see the
screen, please wait 20 seconds and the resolution will automatically
revert back to the previous resolution.
• The 1080p video output frame rate may be automatically set to either
24Hz or 50Hz depending both on the capability and preference of the
connected TV and based on the native video frame rate of the content
on the BD-ROM disc.
COMPONENT VIDEO OUT connection
• For the 1080p resolution setting with unprotected media, real output
resolution of COMPONENT VIDEO OUT will change to 1080i.
• For the 720p, 1080i, 1080p resolution setting with protected media, real
output resolution of COMPONENT VIDEO OUT will change to 576i or
576p depending on the connectivity of HDMI cable.
• BD or DVD could prevent up-scaling on analog output.
VIDEO OUT connection
The resolution of the VIDEO OUT jack is always outputted at 576i
resolution.
17
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 18
Internet connection
This player can be connected to a local area network (LAN) via the LAN
port on the rear panel.
After making the physical connection the player needs to be set up for
network communication. This is done from the [Setup] menu — see
“[NETWORK] Menu” on page 26 for detailed instructions.
• Since there are various connection configurations, please follow the
specifications of your telecommunication carrier or internet service
provider.
Notes:
• Depending on the internet service provider (ISP), the number of devices
that can receive internet service may be limited by the applicable terms
of service. For details, contact your ISP.
Connect the player’s LAN port to the corresponding port on your Modem or
Router using a LAN cable.
Use a commercially available straight LAN cable (Category 5/CAT5 or better with RJ45 connector).
• Our company is not responsible for any malfunction of the player and/or
the internet connection feature due to communication errors/malfunctions associated with your broadband internet connection, or other connected equipment.
By connecting the unit to broadband Internet, you can use a disc that
offers BD-Live function and YouTube features (see page 32-33).
• Our company is not responsible for any trouble in your internet connection.
• The features of BD-ROM discs made available through the Internet
Connection feature are not created or provided by our company, and our
company is not responsible for their functionality or continued availability. Some disc related material available by the Internet Connection may
not be compatible with this player. If you have questions about such
content, please contact the producer of the disc.
BD player
• Some internet contents may require a higher bandwidth connection.
• Even if the player is properly connected and configured, some internet
contents may not operate properly because of internet congestion, the
quality or bandwidth of your internet service, or problems at the provider
of the content.
Broadband
Service
• Some internet connection operations may not be possible due to certain
restrictions set by the Internet service provider (ISP) supplying your
broadband Internet connection.
Router
LAN
Cautions:
• When plugging or unplugging the LAN cable, hold the plug portion of the
cable. When unplugging, do not pull on the LAN cable but unplug while
pressing down on the lock.
• Do not connect a modular phone cable to the LAN port.
18
• Any fees charged by an ISP including, without limitation, connection
charges are your responsibility.
• A 10 Base-T or 100 Base-TX LAN port is required for connection to this
player. If your internet service does not allow for such a connection, you
will not be able to connect the player.
• You must use a Router to use xDSL service.
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 19
• A DSL modem is required to use DSL service and a cable modem is
required to use cable modem service. Depending on the access method
of and subscriber agreement with your ISP, you may not be able to use
the internet connection feature contained in this player or you may be
limited to the number of devices you can connect at the same time.
(If your ISP limits subscription to one device, this player may not be
allowed to connect when a PC is already connected.)
• The use of a “Router” may not be allowed or its usage may be limited
depending on the policies and restrictions of your ISP. For details,
contact your ISP directly.
• Your ISP may protect this player from being connected to network when
confirming MAC ADDRESS. In that case, contact your ISP to request to
initialize MAC ADDRESS.
Setting the sound mode
You can select a suitable sound mode. Press SOUND repeatedly until the
desired mode appears on the front panel display or the TV screen.
The setting the sound mode is not available when [HDMI Audio] is set to
[On] (see page 24).
[Natural] mode: You can enjoy comfortable and natural sound.
[Bypass] mode: Software with multichannel surround audio signals
is played according to the way it was recorded.
[Bass Booster] mode: Reinforce the bass sound effect from front left
and right speaker and subwoofer.
[PL ll Movie] mode: Performs Pro Logic ll movie mode decoding to
the input signal and produces five full-bandwidth output channels from
2 channel sources. This setting is ideal for watching videos of
overdubbed or old movies. This mode is available only to 2 channel
sources.
[PL ll Music] mode: Performs Pro Logic ll music mode decoding to
the input signal and produces five full-bandwidth output channels from
2 channel sources. This setting is ideal for normal stereo sources such
as CD. This mode is available only to 2 channel sources.
[News] mode: This mode makes voice sound clear, improving the
quality of voice sound. This mode outputs sound from the front left and
right speakers, center speaker, and subwoofer.
[Drama] mode: You can enjoy more dynamic sound with improved
center channel while watching a television drama. This mode outputs
sound from the front left and right speakers, center speaker, and
subwoofer.
[Sports] mode: This mode produces dynamic sound expansion for the
sports program.
[Game] mode: You can enjoy more virtual sound while playing video
games.
[Concert] mode: Creates the sound of concert hall.
[Music ReTouch] mode: When listening to MP3 files or other
compressed music, you can enhance the sound. This mode is
available only to 2 channel sources.
Note:
Only [BYPASS] mode is available when [HD Audio Effect] is set to [off] and
playing a source that contains Dolby Digital Plus, Dolby TrueHD and DTS-HD.
Adjust the speaker level settings
You can adjust the sound level of each speaker.
Press SPK LEVEL repeatedly to select a desired speaker to set.
Press VOL. (+/-) to adjust the sound level of the selected speaker while
the level setting menu is displayed on the front panel display or the TV
screen. Repeat and adjust the sound level of the other speakers.
Using the late night function
You can compress the dynamic range of the sound track.
Press NIGHT repeatedly.
This may be useful when you want to watch movies at low volumes late at
night.
[NIGHT OFF]: Late night function off.
[NIGHT ON]: Reduction in dynamic range.
Notes:
• The late night function may be less effective or have no effect depending
on the source.
• During the late night mode is on, the lighting of the touch buttons and
the volume knob are turned off and the front panel display is dimmed.
Using the sleep timer
You can set the system to turn off at a preset time, so you can fall asleep
listening to music.
- Press SLEEP repeatedly to select the desired time period options
(in minutes): (Dimmer on t Sleep timer value t Dimmer off)
Dimmer on: The lighting of the touch buttons and the volume knob are
turned off and the front panel display is dimmed.
- To view the time countdown to the standby mode, press SLEEP again.
- To deactivate the sleep timer, press SLEEP until the previous status is
displayed or press POWER to switch the unit to standby.
19
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 20
Notes:
Using USB devices
This unit can play the movie, music and photo
files contained on the USB device.
ON REMOTE
1. Connect a USB device:
–
2 Displays the [Home Menu]:
HOME
3 Select a main option:
[Movie], [Photo] or [Music] option
b B, ENTER
4 Select the [USB] option:
bB
5 Displays corresponding menu list:
[MOVIE], [PHOTO] or [MUSIC] menu appears.
Details for the menu are on pages 33-37.
ENTER
• This unit supports only USB Flash Drive and USB External HDD with
FAT16 or FAT32 format.
• The USB device can be used for the local storage for enjoying
BD-Live discs with Internet.
• This unit can support up to 4 partitions of the USB device.
• Do not extract the USB device during operation (play, etc.).
• A USB device which requires additional program installation when you
have connected it to a computer is not supported.
• USB device: USB device that support USB1.1 and USB2.0.
• Movie files (DivX), Music files (MP3/WMA) and photo files (JPEG/PNG)
can be played. For details of operations on each file, refer to relevant
pages.
Tip:
If you select the [Movie], [Photo] or [Music] option when the USB device is
connected and a disc is inserted simultaneously, the menu for selecting a
media will appear. Select a media then press ENTER.
For example:
• Regular back up is recommended to prevent data loss.
• If you use a USB extension cable or USB HUB, the USB device may not
be recognized.
• Some USB devices may not work with this unit.
• Digital camera and mobile phone are not supported.
• USB Port of the unit cannot be connected to PC. The unit cannot be
used as a storage device.
Inserting/Removing the USB device
Inserting the USB device – Insert straight-in until it fits into place.
Removing the USB device – Withdraw the USB device or cable
carefully.
USB External HDD
BD player
20
USB Flash Drive
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 21
Using the Home Menu
Adjust the Setup settings
ON REMOTE
ON REMOTE
1 Displays the [Home Menu]:
HOME
1 Displays the [Home Menu]:
HOME
2 Select an option:
bB
2 Select the [Setup] option:
b B, ENTER
3 Displays the selected option menu:
ENTER
3 Select a desired option on the first level:
vV
4 Exit the [Home Menu]:
HOME
4 Move to second level:
B
5 Select a desired option on the second level:
vV
6 Move to third level:
B
7 Adjust or confirm the setting:
Some items require additional steps.
v V, ENTER
8 Go back to the previous level:
b
9 Exit the [Setup] menu:
HOME or RETURN
[Movie] – Start video media’s playback or displays the [MOVIE] menu.
[Photo] – Displays [PHOTO] menu. (page 36-37)
[Music] – Displays [MUSIC ]menu. (page 35-36)
[YouTube] – Watch YouTube videos streamed from the Youtube server via
the internet to your TV. (page 38-40)
[Setup] – Displays the [Setup] menu. (page 21-27)
Tip:
If you select the [Movie], [Photo] or [Music] option when the USB device
is connected and a disc is inserted simultaneously, the menu for
selecting a media will appear. Select a media then press ENTER.
Notes:
• The unit will be in stop mode then the [Home Menu] will appear if you
press HOME during playback.
• If you insert a DVD or an unplayable disc that is formatted as ISO9660
or UDF, the [Movie], [Photo] or [Music] option can be selected in the
[Home Menu]. But you cannot play it.
First level
Second level
Third level
21
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 22
[DISPLAY] Menu
Resolution
Sets the output resolution of the Component and HDMI video signal.
Refer to “Resolution Setting” on page 16-17 for details about the
resolution.
[Auto] – If the HDMI OUT jack is connected for TVs providing display
information (EDID), automatically selects the resolution best suited to
the connected TV. If the COMPONENT VIDEO OUT is only connected,
this changes the resolution to 1080i as default resolution.
[1080p] – Outputs 1080 lines of progressive video (only for HDMI
connection).
TV Aspect Ratio
[4:3 Letter Box] – Select when a standard 4:3 TV is connected.
Displays theatrical images with masking bars above and below the
picture.
[4:3 Pan Scan] – Select when a standard 4:3 TV is connected.
Displays pictures cropped to fill your TV screen. Both sides of the
picture are cut off.
[16:9 Original] – Select when a 16:9 wide TV is connected. The 4:3
picture is displayed with an original 4:3 aspect ratio, with black bars
appearing at the left and right sides.
[16:9 Wide] – Select when a 16:9 wide TV is connected. The 4:3
picture is adjusted horizontally (in a linear proportion) to fill the entire
screen.
Note:
You cannot select [4:3 Letter Box] and [4:3 Pan Scan] option when the resolution is set to higher than 720p.
[1080i] – Outputs 1080 lines of interlaced video.
[720p] – Outputs 720 lines of progressive video.
[576p] – Outputs 576 lines progressive video.
[576i] – Outputs 576 lines of interlaced video.
1080p Display Mode
When the resolution is set to 1080p, select [24Hz] for smooth presentation
of film material (1080/24p) with a HDMI-equipped display compatible with
1080/24p input.
Notes:
• When you select [24Hz], you may experience some picture disturbance
when the video switches video and film material. In this case, select
[50Hz].
• Even when [1080p Display Mode] is set to [24Hz], if your TV is not
compatible with 1080/24p, the actual frame frequency of the video
output will be 50Hz or 60Hz to match the video source format.
HDMI Color Setting
Select the type of output from the HDMI OUT jack. For this setting, please
refer to the manuals of your display device.
[YCbCr] – Select when connecting to a HDMI display device.
[RGB] – Select when connecting to a RGB display device.
22
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 23
[LANGUAGE] Menu
[AUDIO] Menu
Display Menu
Speaker Setup
Select a language for the [Setup] menu and on-screen display.
To obtain the best possible sound, use the Speaker Setup display to
specify the volume of the speakers you have connected and their distance
from your listening position. Use the Test to adjust the volume of the
speakers to the same level.
Disc Menu / Disc Audio / Disc Subtitle
Select the language you prefer for the audio track (disc audio), subtitles,
and the disc menu.
[Speaker] – Select a speaker that you want to adjust.
[Original] – Refers to the original language in which the disc was
recorded.
[Volume] – Adjust the output level of each speaker.
Be sure to set “Test” to “All” for easy adjustment.
[Other] – Press ENTER to select another language. Use number
buttons then ENTER to enter the corresponding 4-digit number
according to the language code list on page 46.
[Distance] – Adjust the distance between each speaker and the
listening position.
[Off] (for Disc Subtitle) – Turn off Subtitle.
Note:
Depending on a disc, your language setting may not work for some disc.
[Test] – The speakers will emit a test tone.
All: The test tone is emitted from each speaker in sequence.
To save your settings, press ENTER and select [Yes] by pressing b / B.
23
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 24
HD Audio Effect
[LOCK] Menu (Parental Control)
Selects whether to mix or not mix primary audio and secondary audio.
The [LOCK] settings affect only BD and DVD playback.
[Off] – Outputs the primary audio only.
[On] – Outputs the audio obtained by mixing the primary audio,
secondary audio and sound effects.
HD AV Sync
Sometimes Digital TV encounters a delay between picture and sound. If this
happens you can compensate by setting a delay on the sound so that it
effectively ‘waits’ for the picture to arrive: this is called HD AV Sync.
Use v V to scroll up and down through the delay amount, which you can set
at anything between 0 and 300m sec.
The delay will vary depending on which digital TV channel you are on. If you
change channel you may need to readjust the HD AV Sync.
HDMI Audio
To access the any features in [LOCK] settings, you must enter the 4-digit
security code you have created.
If you have not entered a password yet, you are prompted to do so. Enter
a 4-digit password and press ENTER. Enter it again and press ENTER to
verify.
You can set TV speaker output for the audio signal from the HDMI OUT jack.
Password
[Off] – Audio signals are output to the system speakers only.
[On] – Audio signals are output from the TV’s speaker and the
system’s front left and right speaker and subwoofer.
Note:
When [HDMI Audio] is set to [On], the sound mode is switched to
[BYPASS] automatically.
You can create, change or delete the password.
[New] – Enter a 4-digit password and press ENTER. Enter it again and
press ENTER to create a new password.
[Change] – Enter the current password and press ENTER.
Enter a 4-digit password and press ENTER. Enter it again and press
ENTER to create a new password.
[Delete] – Enter the 4-digit password and press ENTER to delete the
password.
Tip:
If you make a mistake before pressing ENTER, press CLEAR. Then input
the correct password.
If you forget your password
If you forget your password, you can clear it using the following steps:
1 Remove any disc that might be in the player.
2 Highlight [Password] in the [LOCK] option.
3 Use Number buttons to enter “210499”. The password is cleared.
24
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 25
Rating
Blocks playback of rated disc based on their content. (Not all discs are
rated.)
[Rating 1-8] – Rating one (1) has the most restrictions and rating eight
(8) is the least restrictive.
[Unlock] – If you select unlock, parental control is not active and the
disc plays in full.
BD Age
Set an age limit of BD-ROM play. Use number buttons to input an age limit
for BD-ROM viewing.
[255] – All BD-ROM can be played.
[0-254] – Prohibits play of BD-ROM with corresponding ratings
recorded on them.
Area Code
Enter the code of the area whose standards were used to rate the DVD
video disc, based on the list on page 46.
25
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 26
How to check the network configuration
[NETWORK] Menu
The [NETWORK] settings are needed to use the BD Live and YouTube
feature.
Some BD-ROM discs may enable you to access special BD-ROM sites, if
you connect the player to the Internet. For example, if a BD-ROM site
includes content such as links to future movie trailers, you can watch the
downloaded on-line content on the player.
You do not need to connect to a PC to use this function.
Preparations:
• This feature requires an always-on broadband internet connection.
(see page 18-19.)
• A BD-ROM disc compatible with this feature is required. Not all BDROM discs are compatible.
Select [IP Mode] option and check the Network status indicator shown
above the menu. (The Network status indicator changes according to
Network configuration.)
Able to use network
Testing Network
Unable to use network
IP Setting
This option is available only if [IP Mode] option is set to [Static IP].
Use the v / V / b / B buttons to select a field; use the number buttons to
enter a value. Press ENTER when [OK] is highlighted to finish and exit the
screen.
BD-LIVE connection
You can restrict Internet access when BD-Live functions are used.
[Permitted] – Internet access is permitted for all BD-Live contents.
[Partially permitted] – Internet access is permitted only for BD-Live
contents which have content owner certificates. Internet access and
AACS Online functions are prohibited for all BD-Live contents without
a certificate.
IP Mode
If there is a DHCP server on the local area network (LAN), this player will
automatically be allocated an IP address. If you’re using a broadband
router or broadband modem that has a DHCP (Dynamic Host
Configuration Protocol) server function, select [Dynamic IP]. The IP
address will automatically be determined.
If there is no DHCP server on the network and you want to set the IP
address manually, select [Static IP] then set the [IP Address], [Subnet
Mask], [Gateway] and [DNS Server] using [IP Setting] option.
Note:
The [IP Mode] menu shows if the internet is connected or not. “
appear when connection is failed.
26
” will
[Prohibited] – Internet access is prohibited for all BD-Live contents.
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 27
[OTHERS] Menu
Skin
Changes the background of the initial screen.
Java Font Size
BD
You can adjust the default text size displayed for the BD-J contents during
BD-ROM playback.
This setting is not valid when the size of text on BD-J contents is fixed.
Please select a font size bigger than 24 when the player is connected with
an HD TV.
DivX Registration Code
DivX® is a digital video format created by DivX, Inc. This is an official DivX
Certified or DivX Ultra Certified device that plays DivX video.
This DivX® Certified device must be registered in order to play DivX Videoon-Demand (VOD) content. First generate the DivX VOD registration code
for your device and submit it during the registration process. [Important:
DivX VOD content is protected by a DivX DRM (Digital Rights
Management) system that restricts playback to registered DivX Certified
devices. If you try to play DivX VOD content not authorized for your device,
the message “Authorization Error” will be displayed and your content will
not play.]. Learn more at www.divx.com/vod.
Press ENTER or B when [DivX Reg. Code] is highlighted and you can
view the registration code of the unit.
Note:
All the downloaded videos from DivX® VOD can only be played back on
this unit.
Initialize
You can reset the player to its original factory settings, initialize the BD
storage or deactivate the player.
[Factory Set] – If you need to, you can reset the player to all its factory settings. Some options cannot be reset. (Rating, Password and Area
Code, etc.)
[BD Storage Clear] – Initializes the BD contents from the connected
USB device.
27
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 28
Resume playback ALL
Play a disc
ON REMOTE
1 Open the disc tray:
Z)
OPEN/CLOSE (Z
2 Insert a disc:
-
3 Close the disc tray:
Z)
OPEN/CLOSE (Z
4 Adjust the disc menu settings:
A disc menu may not appear on the screen
depending on the disc.
v V b B, ENTER
5 Starts playback:
N)
PLAY (N
6 Stops playback:
x)
STOP (x
Notes:
•
•
When you turn on the player or replace a disc, the player returns to the
initial default setting. Depending on a disc, a specific type of audio that
the disc has is output.
Depending on the pre-recorded contents of the BD-ROM, some functions may not be available or may be operated differently than other
media.
If a disc menu screen is displayed
BD
DVD
AVCHD
The menu screen may be displayed first after loading a disc which contains
a menu.
Use b / B / v / V buttons to select the title/chapter you want to view, then
press ENTER to start playback.
Skip to the next/previous chapter/track/file ALL
During playback, press . or > to go to the next chapter/track/file or
to return to the beginning of the current chapter/track/file.
Press . twice briefly to step back to the previous chapter/track/file.
During playback, press STOP (x) to stop playback.
The unit records the stopped point, depending on the disc. “Xx” appears
on the screen briefly. Press PLAY (N) to resume playback (from the
scene point). If you press STOP (x) again or unload the disc (“x” appears
on the screen.), the unit will clear the stopped point. (Xx = Resume Stop,
x = Complete Stop)
Notes:
• The resume point may be cleared when a button is pressed
(for example; POWER, OPEN/CLOSE, etc).
• On BD-Video discs including BD-J, the resume play function does not
work.
• On BD-ROM interactive title, the unit will be in Complete Stop mode if
you press STOP once during playback.
Pause a playback ALL
During playback, press PAUSE/STEP (X) to pause playback. Press PLAY
(N) to continue playback.
Tip: During Audio CD or MP3/WMA playback, press X once again to
resume playback.
Frame-by-Frame playback
BD
DVD
DivX
Press PAUSE/STEP (X) repeatedly to play Frame-by-Frame playback.
Slow down the playing speed
BD
DVD
AVCHD
DivX
While the playback is paused, press SCAN M repeatedly to play in slow
motion (4 steps, forward only).
Fast forward or fast reverse ALL
Press SCAN (m or M) to play fast forward or fast reverse during
playback.
You can change the various playback speeds by pressing SCAN (m or
N) to continue play at normal speed.
M) repeatedly. Press PLAY (N
Note:
This function may not work on some disc or titles.
28
AVCHD
HB954TB-AD.BINDLLK_ENG_6445
Playing repeatedly
BD
5/26/09
DVD
10:00 AM
ACD
MP3
Page 29
WMA AVCHD
During playback, press REPEAT repeatedly to select a desired repeat
mode. The current title, chapter or track will be played back repeatedly. To
return to normal playback, press REPEAT repeatedly to select [OFF].
Note:
If you press > once during Repeat Chapter/Track playback, the repeat
playback cancels.
DVD
BD
DVD
AVCHD
DivX
To enter a Marker
You can start playback from up to nine memorized points. To enter a marker, press MARKER at the desired point on the disc. The Marker icon
appears on the TV screen briefly. Repeat to enter up to nine markers.
To Recall or Clear a Marked Scene
Press SEARCH and the search menu appears on the screen.
Press a number button to select a marker number that you want to recall.
Playback starts from the marked scene.
Viewing the Title menu or Popup menu
BD
Marker Search
AVCHD
Press TITLE/POPUP to display the title menu or popup menu.
If the current DVD or BD-ROM disc has a menu, the Title menu or Popup
menu appears on the screen. Depending on the disc, the menu may not be
available.
OR
Press V to highlight a marker number. Use b / B to select a marked scene
that you want to recall or clear.
Press ENTER and playback starts from the marked scene. Press CLEAR
and the marked scene is erased from the search menu.
Using the search menu
Notes:
• This function may not work on some discs or titles.
• All marked points are cleared if you press STOP (x) twice (complete
stop), the title is changed or if you unload the disc.
BD
DVD
AVCHD
DivX
During playback, press SEARCH to display the search menu.
Press b / B to skip the playback by about 15 seconds forward or
backward.
Tip:
You can select a point that you want to skip by pressing and holding b / B
button.
29
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
Selecting a subtitle language
10:00 AM
BD
DVD
Page 30
AVCHD
DivX
During playback, press SUBTITLE repeatedly to select a desired subtitle
language.
OR
During playback, press DISPLAY to display the playback menu.
Use v V to select the [Subtitle] option then use b B to select desired
subtitle language.
Note:
Some discs allow you to change subtitle selections only via the disc menu.
If this is the case, press TITLE/POPUP or DISC MENU button and choose
the appropriate subtitle from the selections on the disc menu.
Hearing a different audio
BD
DVD
AVCHD
DivX
During playback, press DISPLAY to display the playback menu.
Use v V to select the [Audio] option then use b B to select desired
audio language or audio track.
Notes:
• Some discs allow you to change audio selections only via the disc
menu. If this is the case, press TITLE/POPUP or DISC MENU button
and choose the appropriate audio from the selections on the disc menu.
• Immediately after you have switched sound, there may be a temporary
discrepancy between the display and actual sound.
• On BD-ROM disc, the multi audio format (5.1CH or 7.1CH) is displayed
with [MultiCH] in the on-screen display.
Using coloured (A, B, C, D) Buttons
BD
These buttons are available only during BD-J contents playback. Use the
appropriate buttons as indicated by the display. Depending on the disc
contents, the functions of each button may differ.
Last Scene Memory
BD
DVD
This unit memorizes last scene from the last disc that is viewed. The last
scene remains in memory even if you remove the disc from the unit or
switch off the unit. If you load a disc that has the scene memorized, the
scene is automatically recalled.
30
Notes:
• Settings are stored in memory for use any time.
• This unit does not memorize settings of a disc if you switch off the unit
before commencing to play it.
• Last Scene Memory function for a previous disc is erased once a
different disc is played.
• This function may not work depending on the disc.
Screen Saver
The screen saver appears when you leave the player in Stop mode for
about five minutes.
Note:
Depending on the unit status, the screen saver may not appear.
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 31
Moving to another title/chapter
Displaying disc information
BD
ON REMOTE
1 Play the disc loaded on the unit:
PLAY
2 Displays the playback menu:
DISPLAY
3 Select an item:
vV
4 Adjust the playback menu settings:
bB
5 Exit the disc playback menu:
DISPLAY
a
b
c
d
e
f
a
b
c
d
e
f
Title – Current title number/total number of titles.
Chapter – Current chapter number/total number of chapters.
Time – Elapsed playing time.
Audio – Selected audio language or channel.
Subtitle – Selected subtitle.
Angle – Selected angle/total number of angles.
DVD
AVCHD
DivX
When a disc has more than one title/chapter, you can move to
another title/chapter/track.
Press DISPLAY during playback then use v / V to select the
[Title/Chapter] icon. Then, press the appropriate numbered button
(0-9) or b / B to select a title/chapter number.
Playing from selected time
BD
DVD
AVCHD
DivX
Press DISPLAY during playback. The time search box shows the elapsed
playing time. Select the [Time] option and then input the required start time
in hours, minutes, and seconds from left to right. For example, to find a
scene at 2 hours, 10 minutes, and 20 seconds, enter “21020” and press
ENTER. If you enter the wrong numbers, press CLEAR and enter the
correct numbers.
Note:
This function may not work on some disc or titles.
Watching from a different angle
BD
DVD
If the disc contains scenes recorded at different camera angles, you can
change to a different camera angle during playback.
During playback, press DISPLAY to display the playback menu. Use v V
to select the [Angle] option, then use b B to select desired angle.
Notes:
• If no button is pressed for a few seconds, the on-screen display
disappears.
• A title number cannot be selected on some discs.
• An item may not be available on some discs or titles.
• If BD interactive title is playing back, some setting information is
displayed on the screen but prohibited to be changed.
31
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 32
Caution:
Enjoying BD-LIVE™
ON REMOTE
1 Inserts a BD-ROM disc with BD-LIVE™
features:
OPEN/CLOSE (Z)
2 Check the network connection and settings:
BD-Live features need the internet connection.
–
3 Connect a USB device:
A USB device is required to use this function.
–
4 Select a BD-LIVE™ features on the
disc menu:
v V b B, ENTER
This unit allows you to enjoy functions such as picture-in-picture,
secondary audio and Virtual packages, etc., with BD-Video supporting
BONUSVIEW (BD-ROM version 2 Profile 1 version 1.1/ Final Standard
Profile). In addition to the BONUSVIEW function, BD-Video supporting
BD-Live (BD-ROM version 2 Profile 2) that has a network extension
function allows you to enjoy more functions such as online games by
connecting this unit to the Internet.
Enjoying BD-Live discs with Internet
This unit supports BD-Live, a new BD-Video function that allows you to use
the following interactive functions when connected to the Internet. (The
usable functions and the operating method may vary with each disc. For
details, refer to the instructions for the disc.)
–
Additional contents such as movie’s trailer, subtitles and BD-J, etc. can
be downloaded to USB device to play them.
–
Special video data, etc. may be played back while they are being
downloaded to a USB device.
Preparations:
• The unit must be connected to the Internet and set up to use the
BD-Live functions (see page 18-19 and 26).
• A USB device is required to use this function. Connect a USB device
(see page 20).
• The free space in the USB device must be more than 1GB.
32
Do not extract the connected USB device while content is being
downloaded or a Blu-ray disc is still in the disc tray. Doing so may damage
the connected USB device and BD-Live features may not operate properly
with the damaged USB device anymore.
If the connected USB device seems damaged from such an action, you
can format the connected USB device from the PC and reuse it with this
player.
Notes:
• Some BD-Live contents may be restrictively accessed in some
territories by contents provider’s own decision.
•
It may take up to several minutes to load and start enjoying BD-Live
contents.
•
Depending on a disc, the BD-Live function may not be operated if [BDLIVE connection] option is set to [Partially permitted]. (See page 26.)
•
The connection to the Internet may take time or the Internet may not
be connected depending on the connection environment. It is required
that you use a broadband connection.
•
Do not remove the USB device during operation. The USB device may
be damaged. Stop playback and turn off the menu beforehand.
Tip:
Special video data, etc. may be played back while they are being
downloaded to a USB device using one function of BD-Live. The playback
may be paused depending on the communication environment.
Some functions may be disabled to prevent skipping to sections that have
not been downloaded, etc.
AACS Online
When discs supporting BD-Live are played back, the player or disc IDs
may be sent to the content provider via the Internet.
Services and functions to be provided differ depending on the disc.
– You can be introduced to other similar movies if you record your
viewing history on the server by using these IDs.
–
Game score histories can be saved.
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 33
Playing secondary video (picture-in-picture)
Playing a movie
Secondary video can be played from a disc compatible with the picture-inpicture function.
For the playback method, refer to the instructions for the disc.
To turn on/off secondary video, press PIP. Secondary video is played.
Press the button to turn it ON or OFF.
The player can play DivX files on the disc/USB
device and video contents recorded on a
DVD-RW(VR mode) discs. Before playing DivX
files, read “DivX file requirement” on page 34.
Notes:
• Discs may not always be played back according to the settings on this
unit, as certain playback formats are prioritized on certain discs.
• Only the primary video is played during search/slow-motion or frame-byframe.
• This function may not work depending on the disc.
ON REMOTE
1 Insert a disc/ USB device containing movie
contents.
–
2 Displays the [Home Menu]:
HOME
3 Select the [Movie] option:
b B, ENTER
4 Selects a movie from the [MOVIE] menu:
vV
5 Plays the selected movie:
PLAY
6 Stops the playback:
STOP
Note:
• When the USB device is connected and a disc is inserted
simultaneously, the menu for selecting a media will appear.
Select a media then press ENTER.
• You can use various playback functions. Refer to pages 28-31.
• On the [MOVIE] menu, use red (A) or blue (D) button to move to the
previous or next page.
• Unfinalized DVD VR format discs may not be played in this player.
• Some DVD-VR disc are made with CPRM data by DVD RECORDER.
This unit cannot support these kinds of discs.
• Some DivX files may not play, depending on the DivX format or the
recording format.
•
Press DISC MENU to move to the list menu.
What is CPRM?
CPRM is a copy protection system (with scramble system) only allowing
the recording of ‘copy once’ broadcast programs. CPRM stands for
Content Protection for Recordable Media.
33
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 34
Movie List menu options (DVD-RW (VR mode disc))
Use v / V to select a title on the [MOVIE] menu then press ENTER. The
menu options appear.
DivX file requirement
DivX file compatibility with this player is limited as follows:
•
•
•
•
Available resolution size: 720x576 (W x H) pixel.
The file names of DivX and subtitle are limited to 50 characters.
DivX file extensions: “.avi”, “.divx”, “.mpg”, “.mpeg”
Playable DivX subtitle: SubRip (.srt / .txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt), MicroDVD (.sub/.txt), SubViewer 1.0 (.sub),
SubViewer 2.0 (.sub/.txt), TMPlayer (.txt), DVD Subtitle System (.txt)
• Playable Codec format: “DIVX3.xx”, “DIVX4.xx”, “DIVX5.xx”,
“DIVX6.xx” (Standard playback only)
• Only the playback function is supported with DivX 6.0 in the unit.
• Playable Audio format: “Dolby Digital”, “DTS”, “MP3”
• Sampling frequency: within 32 - 48 kHz (MP3)
Use v / V to select an option, then press ENTER.
• Bit rate: within 32 - 320 kbps (MP3)
• [Resume Play] Starts playback from where you stopped it previously.
• CD-R/RW, DVD±R/RW, BD-R/RE Format:
ISO 9660+JOLIET, UDF and UDF Bridge format
• [Close] Exits menu options. Also you can disappear it by pressing
RETURN button.
• Maximum Files/Folder:
Less than 1999 (total number of files and folders)
• [Play] Starts playback of the selected title.
Notice for displaying the DivX subtitle
If the subtitle does not display properly, change the language code as
described below.
1 Press and hold SUBTITLE for 3 seconds during playback.
The language code will appear.
2 Press SUBTITLE repeatedly to select another language code until the
subtitle is displayed properly and then press ENTER.
34
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 35
Listening to a music
The player can play Audio CDs and MP3/WMA
files. Before playing MP3/WMA files, read
“MP3/WMA audio file requirement” on page 36.
1 Insert Audio CD or a disc containing MP3/
WMA files, or connect the USB device
containing MP3/WMA files.
2 Displays the [Home Menu]:
3 Select a [Music] option:
4 Selects a music from the [MUSIC] menu:
5 Plays the selected music:
6 Stops the playback:
ON REMOTE
–
•
On the [MUSIC] menu, use red (A) or blue (D) button to move to the
previous or next page.
•
The equalizer indicator is not coupled with the music in play back.
•
If there is impossible code to express in the file name, it may be
displayed as illegible.
•
You can use variable playback functions. Refer to page 28-29.
The [MUSIC] menu options
HOME
b B, ENTER
vV
PLAY
STOP
Example) Audio CD
Note:
When the USB device is connected and a disc is inserted simultaneously,
the menu for selecting a media will appear. Select a media then press
ENTER.
Tips:
• To go directly to any track or file and play, enter the track/file number
using the numbered buttons (0-9).
•
The playback may start automatically if the Audio CD inserted.
•
Select a folder then press ENTER and you can view the files in the
folder. If you want to move to the upper directory, use b or v/V to
highlight [UP Folder] and press ENTER.
Use v / V to select a track or file on the [MUSIC] menu then press
ENTER. The menu options appear.
Use v / V to select an option, then press ENTER.
• [Play] Starts playback the selected track or file.
• [Select Play] Plays back only the marked track(s) or file(s). Use
MARKER for selecting the multiple files or tracks.
• [Random] Starts or stops random playback.
By pressing > during random playback, the unit selects another
track and resumes random playback.
• [Unmark All] Unmarks all marked files or tracks.
• [Close] Exits menu options. Also you can disappear it by pressing
RETURN button.
Note:
You cannot use [Select Play] and [Random] functions simultaneously.
35
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 36
MP3/WMA audio file requirement
Viewing a photo
File extensions: “.mp3”, “.wma”
This unit can play a photo files. Before playing
photo files, read “Photo file requirement” on page
37.
Sampling frequency: within 32 - 48 kHz (MP3),
within 32 - 48 kHz (WMA)
Bit rate: within 32 - 320 kbps (MP3), within 40 - 320 kbps (WMA)
ON REMOTE
CD-R/RW, DVD±R/RW, BD-R/RE Format:
ISO 9660+JOLIET, UDF and UDF Bridge format
1 Insert a disc containing photo files, or connect
the USB device containing photo files.
–
Maximum Files/Disc:
Less than 1999 (total number of files and folders)
2 Displays the [Home Menu]:
HOME
3 Select a [Photo] option:
b/B, ENTER
Notes on MP3/WMA file
• Depending on the size and number of the MP3/WMA files, it may take
several minutes to read the contents of the media.
• This unit cannot support the ID3 Tag embedded in the MP3 file.
4 Selects a photo from the [PHOTO] menu:
v/V/b/B
5 Displays the selected photo in full screen:
ENTER
6 Displays the next or previous photo:
./>
7 Return to the [PHOTO] menu screen:
STOP
Note:
When the USB device is connected and a disc is inserted
simultaneously, the menu for selecting a media will appear. Select a media
then press ENTER.
Tips:
• To go directly to any file and play, enter the file number using the
numbered buttons (0-9).
36
•
You can advance to the previous or next file by pressing . or >
during viewing a photo file in full screen.
•
You can start the slide show by pressing PLAY (N) while the
[PHOTO] menu appears.
HB954TB-AD.BINDLLK_ENG_6445
•
5/26/09
10:00 AM
Page 37
Select a folder then press ENTER and you can view the files in the
folder. If you want to move to the upper directory, use v/V/b/B to
highlight [UP Folder] and press ENTER.
•
On the [PHOTO] menu, use red (A) or blue (D) button to move to the
previous or next page.
•
If there is impossible code to express in the file name, it may be displayed as illegible.
Options during viewing a photo file in full screen
You can use various options during viewing a picture in full screen.
Use v V b B to select an option and use the options as described below.
a
b
c
d
e
f
Photo file requirement
File extensions: “.jpg”, “.jpeg”, “.png”
Recommended size:
Less than 3,000 x 3,000 x 24 bit/pixel
Less than 3,000 x 2,250 x 32 bit/pixel
CD-R/RW, DVD±R/RW, BD-R/RE Format:
ISO 9660+JOLIET, UDF and UDF Bridge format
Maximum Files/Disc:
Less than 1999 (total number of files and folders)
Notes on Photo file
• Progressive and lossless compression photo image files are not
supported.
• Depending on the size and number of the photo files, it may take
several minutes to read the contents of the media.
g
a Use b/B to advance to the previous or next file.
b Press ENTER to start or pause the slide show.
c Press ENTER to play or pause the background music. This option
is available after the background music is selected using
[Music Select] option.
d Press ENTER to rotate the picture clockwise.
This option is not available during slide show.
e Press ENTER to set the Slide Show speed.
f Selects the background music.
1) Press ENTER and the menu will appear.
2) Use v/V/b/B to select a media or folder that there are music
file(s).
3) Press ENTER to confirm your selection.
g Press ENTER to exit the option menu.
To appear the menu again, press ENTER.
37
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 38
a Featured – The featured videos list will be displayed.
b Recent Videos – The most recently updated videos list will be
displayed.
c Most Viewed – The most viewed videos list will be displayed. The
period option appears at the bottom of the screen.
d Top Rated – The best rated videos list from YouTube server will be
displayed. The period option appears at the bottom of the screen.
e Search – The keyboard menu will be displayed.
See “Searching videos” on page 40 for more detail.
f History – The list of videos that you recently played on this unit will
be displayed. Maximum of 25 videos can be displayed.
g Favorites – This option will be appeared only when the unit is in
sign-in status. Displays the videos list that is arranged in the
YouTube server with your account.
Some videos may not appear on the [Favorites] list, even if the
videos are arranged in the server.
h Sign in (Sign Out) – Displays the keyboard menu to sign in or
returns to the sign-out status. See “Sign in with your YouTube
account” on page 40 for more details.
i Local site – Choose which country's videos you would like to view.
The countries listed on the [Local Site] menu may different with
those listed on the YouTube web site.
Playing YouTube videos
ON REMOTE
1 Check the network connection and settings:
See page 18-19 and 26 of the main manual.
–
2 Check the network configurations:
See page 26 of the main manual.
–
3 Displays the [Home Menu]:
HOME
4 Select the [YouTube] option:
b B, ENTER
5 Select a desired option on the YouTube
menu:
b B, ENTER
6 Select a video you want to play:
bB
7 Start playback the selected video:
N), ENTER
PLAY (N
or DISPLAY
Network condition
YouTube menu
videos list
period options
Notes:
• The YouTube menu can display 5 videos in the videos list. Press red or
blue button to display next/previous 5 videos.
•
If you select the [Most Viewed] or [Top Rated] option in the YouTube
menu, the period options appear at the bottom of the screen. Use v V
b B to select a period option and press ENTER to display the videos
list within the selected period.
•
The videos list searched from the player may different with the list
searched from a web browser on PC.
About the YouTube menu
There are various options on the YouTube menu. Use v V b B to select
an option and press ENTER to select the options as described below.
a
b
f
38
c
g
d
h
e
i
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 39
About YouTube playback screen
When you press PLAY (N) or ENTER at the video you want to watch, the
playback screen and content detail will appear on the screen.
playback
screen
content detail
progress bar
while playing
And when the playback ends or stops, the stopped playback screen and
related videos list appear on the screen. Use v V b B to select the current video or a video from the related videos list and then press PLAY (N)
or ENTER to play the selected video.
related videos
list
playback
screen
progress bar
Press DISPLAY to toggle between playback in full screen and playback
screen with content detail.
Playing a video
While watching a video from YouTube via your player, you can control the
YouTube video playback. You can use the buttons on the remote to pause
and resume viewing, just like when you watch a DVD. While playing a
video, the buttons on the remote do the following:
Button(s)
Operations
N or ENTER
Starts playback the video with content detail.
DISPLAY
Toggle between playback in full screen and playback
screen with content detail.
X
To pause a video while it is playing. To resume playing
a paused video, press PLAY (N) again.
x
Stops the video and displays related videos list.
./>
Skip the playback forward or backward .
HOME
When you have finished watching videos, simply press
the HOME button on the remote control to go to the
[Home Menu].
Notes:
• The settings of this player do not affect the YouTube’s playback quality.
while stopped
When you press DISPLAY at the video you want to watch, the playback
starts in full screen.
playback
screen
•
The playback of YouTube videos may be paused, stopped or buffering
occurring often depending on your broadband speed.
We recommend a minimum connection speed of 1.5 Mbps. For the
best playback condition, a connection speed of 4.0 Mbps is required.
Sometimes your broadband speed varies based on your ISP’s network
conditions. Contact your ISP if you have problems maintaining a fast
connection that is reliable, or if you want to increase your connection
speed. Many ISPs offer a variety of broadband speed options.
progress bar
Full Screen
39
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 40
Searching videos
You can search for videos by entering search words of up to 128 characters.
Use b B to select [Search] option from the menu and press ENTER to
display the keyboard menu. Use v V b B to select a character then press
ENTER to confirm your selection on the keyboard menu.
When you entering a character, maximum of 5 suggestion words will be
displayed.
To enter a letter with an accent mark, select the letter from extended
character set.
Example: Select “D” and then press DISPLAY to display the extended
character set. Use b B to select “D” or “Ď” and then press ENTER.
[OK]: Searching related videos of search words.
[Clear]: Clear all entered characters.
[Space]: Inserts a space at the cursor position.
[Backspace]: Deletes the previous character at the cursor position.
[ABC / abc / #+-=&]: Change the keyboard menu settings to capital
letter, small letters or symbols.
[OK]: Finish entering an ID or password.
[Clear]: Clear all entered characters.
[Space]: Inserts a space at the cursor position.
[Backspace]: Deletes the previous character at the cursor position.
[ABC / abc / #+-=&]: Change the keyboard menu settings to capital
letters, small letters or symbols.
If you want to sign out, select the [Sign Out] from the YouTube menu and
press ENTER.
This unit can automatically store up to 5 IDs which were previously
signed-in. The IDs list appears when you select the [Sign In] option.
Select a stored ID on the list and press ENTER to display the keyboard
menu with the selected ID is entered. You will then only need to enter the
password to sign in.
When you finish entering the search words, select [OK] and press ENTER
to display the related videos list.
Note:
Available languages to enter on the keyboard menu are as follows:
English, Spanish, Italian, French, German, Dutch, Portuguese, Swedish,
Polish and Czech.
Sign in with your YouTube account
To watch videos from your [Favorites] video list on the YouTube server with
your account, you need to sign in with your YouTube account.
Use b B to select [Sign In] option from the menu and press ENTER to
display the keyboard menu. Use v V b B to select a character then press
ENTER to confirm your selection on the keyboard menu.
40
[New ID]: Displays the keyboard menu for entering a new ID and
password.
[X]: Delete the stored ID as shown left of the [X] symbol.
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 41
Listening to the radio
Be sure that FM and AM antennas are connected.
1 Select FM or AM:
2 Select a radio station:
3 To save a radio station:
A preset number will show on the display.
Up to 50 radio stations can be saved.
4 To confirm press:
5 To select a saved station
Playing the iPod
ON REMOTE
TUNER (INPUT)
TUN.-/+
ENTER
ENTER
V
PRESET v /V
Listening to the radio - more you can do
Look for radio stations automatically
Press and hold TUN.-/TUN.+ for more than a second. The tuner will scan
automatically and stop when it finds a radio station.
Choose a preset number for a radio station
For details about iPod, refer to the iPod User Guide.
Preparation
• To view iPod’s Videos and Photos on the TV screen.
- Be sure to use the video connection through the VIDEO OUT jack on
the rear panel of this unit.
Select the appropriate video input mode on the TV.
- Depending on the iPod, make sure that select Videos > Video settings,
and then set TV Out to Ask or On from your iPod.
For details about Video Settings, refer to the iPod User Guide.
- The viewing photos is available only if this unit is in REMOTE IPOD
mode and you can view photos only as a slideshow.
You have to start a slideshow on your iPod to view a photo on a TV.
For details about a slideshow, refer to the iPod User Guide.
• Before connecting the iPod, turn this unit off and reduce the volume of
this unit to its minimum.
Connect the iPod firmly.
When storing a radio station, the preset number can be chosen. When this unit
V to change it. Press
automatically shows a preset number, press PRESET v /V
ENTER to save your chosen number.
Delete all the saved stations
To open the iPod Dock:
Push the marked Z.
To close the iPod Dock:
Push the iPod Dock forward.
Press and hold ENTER for two seconds. ERASE ALL will flash up on the
display. Press ENTER to erase all saved radio stations.
Improve poor FM reception
Press MO./ST. This will change the tuner from stereo to mono and usually
improve the reception.
• If you turn this unit on, your iPod is automatically turned on and recharging starts.
To
Do this on remote
Select an iPod mode
Press iPod.
• REMOTE IPOD mode: You can operate your iPod through an iPod’s
display by using the supplied remote control and also control on your iPod.
• OSD IPOD mode: You can operate your iPod by controlling OSD menu
on the TV screen with the supplied remote control. The controls on
your iPod are not operational in the OSD iPod mode.
41
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 42
To
Do this on remote
Notes:
Select a menu item
Press v V and B or ENTER.
Go back to the previous menu
O) or DISC MENU or b.
Press RETURN (O
Browse for a song
From the main menu, select Music.
• Compatibility with your iPod may vary depending on the type of your iPod.
• iPod touch and iPhone have may differ in operation from the iPod.
You may need any additional control to use them with this unit.
(e.g. “slide to unlock”)
• If you use an application, make a call, or send and receive SMS text
message, etc. on your iPod touch or iPhone, disconnect it from the
iPod dock of this unit and then use it.
• Depending on your iPod’s software version, it may not be possible to
control your iPod from this unit. We recommend installing the latest
software version.
• The video quality depends on the video sources on your iPod.
• When LG TV’s SIMPLINK is set to On, the audio signals are output to the
system speakers only.
• If this unit displays an error message, follow the message.
An error message “CHECK IPOD” or “Please check your iPod.”
appears when:
- the communication between this unit and your iPod is failed.
t Undock & re-dock your iPod in this unit.
- your iPod is not connected firmly.
- this unit recognizes your iPod as unknown device.
- your iPod is exceptionally low on power.
t The battery needs to be charged.
t If you charge the battery while iPod is extremely low in power, it may
take longer to charge.
An error message “CHECK IPOD” or “Connected iPod model is not
supported.” appears when:
- your iPod is not available for the function to be operated.
An error message “CHECK IPOD” or “Please update iPod’s software.”
appears when:
- your iPod has an old software version.
t Update your iPod software to latest version.
• If you have a problem with your iPod, please visit
www.apple.com/support/ipod.
Browse for a video
From the main menu, select Videos.
Play a song or video
Select the song or video and press ENTER.
Pause a song or video
X) or PLAY (B).
Press PAUSE/STEP (X
To continue playback, press
X) or PLAY (B) again.
PAUSE/STEP (X
Skip to the next song or video Press SKIP (>).
Start a song or video over
Press SKIP (.).
Play the previous song or video
Press SKIP (.) twice.
Fast-forward or rewind a song Press and hold SCAN (m or M).
or video
Repeat a song
Press REPEAT repeatedly to select a
desired repeat mode: Track ( ), All (
Off (No display).
)
Tip:
You may use the dock adapter which should be supplied with your iPod to
the dock for the stable use of the iPod.
If you need an adapter, consult your iPod dealer.
42
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 43
Listening to music from your
portable audio player
Listening to the sound from
your component
You can enjoy the sound of your portable audio player from the speakers
of the system.
3.5 mm stereo
miniplug cable
You can enjoy the sound of your component with the analog audio
output jacks from the speakers of the system.
To the audio output jacks
of your component
(TV, VCR, etc.)
ON REMOTE
ON REMOTE
-
1 Connect the analog audio output jacks of your
component into the AUX L/R (INPUT) on the rear
panel of this unit:
2 Turn the power on:
POWER
2 Turn the power on:
3 Select the [PORTABLE] option:
INPUT
3 Select the [AUX] option:
INPUT
4 Turn down the volume of this unit:
VOL. (+/-)
4 Turn down the volume of this unit:
VOL. (+/-)
5 Turn the portable audio player on and start
it playing:
5 Turn your component on:
-
-
6 Adjust the volume:
VOL. (+/-)
1 Connect the headphones (or line out ) jack
of the portable audio player into the PORT.
IN on the rear panel of this unit:
6 Adjust the volume of this unit and your
portable audio player:
POWER
VOL. (+/-)
43
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 44
Using HDMI IN jacks
Using DIGITAL AUDIO IN jacks
You can enjoy the pictures and sound of your component with the HDMI
OUT jack.
You can enjoy the sound of your component with the digital
optical or coaxial output jack from the speakers of the system.
or
To the digital optical output jack of your component
To the HDMI OUT jack of your component
(set-top box, digital satellite receiver, video game machine, etc.)
To the digital coaxial output jack of your component
ON REMOTE
1 Connect the HDMI OUT jack of your
component into the HDMI IN 1 or 2 jack on
the rear panel of this unit.
-
2 Turn the power on:
POWER
ON REMOTE
1 Connect the optical or coaxial output jack
of your component into the OPTICAL or
COAXIAL (DIGITAL AUDIO IN) jack on the
rear panel of this unit.
-
3 Select the [HDMI IN 1] or [HDMI IN 2] option: INPUT
2 Turn the power on:
POWER
4 Turn down the volume of this unit:
VOL.(+/-)
3 Select the [OPTICAL] or [COAXIAL] option:
INPUT
5 Turn your component on:
-
4 Turn down the volume:
VOL.(+/-)
VOL.(+/-)
5 Turn your component on:
-
6 Adjust the volume:
VOL.(+/-)
6 Adjust the volume of this unit:
Note:
• You cannot change the video resolution at the HDMI IN 1/2 mode.
Change the video resolution of the connected component.
• You cannot operate SIMPLINK function at the HDMI IN 1/2 mode.
• The setting of the sound mode is not available when Dolby Digital
Plus, Dolby TrueHD and DTS-HD are played at HDMI IN 1/2 mode.
• If the video output signal is abnormal when your personal computer is
connected to HDMI IN 1/2 jack, change the resolution of your personal computer to 576p, 720p, 1080i or 1080p.
44
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 45
Setting up the remote to control your TV
Reference
You can operate your LG/GoldStar TV with the supplied remote control.
Controlling a TV with the Supplied Remote Control
You can control the volume, input source, and power state of your
LG/GoldStar TV with the supplied Remote Control.
You can control your TV using the buttons below.
While holding down TV POWER button, press PR/CH v or V.
Release the TV POWER button to complete setting.
When you replace the batteries of the remote, you may have reset the
remote control.
TV Control
Buttons
By pressing
You can
TV POWER
Turn the TV on or off.
INPUT
Switch the TV’s input source between the
TV and other input sources.
V
PR/CH v/V
Scan up or down through memorized
channels.
VOL +/–
Adjust the volume of the TV.
45
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 46
Language Codes
Use this list to input your desired language for Disc Audio, Disc Subtitle and Disc Menu.
Language
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Chinese
Code
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
9072
Language
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Code
7282
6783
6865
7876
6978
6979
6984
7079
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
Language
Hausa
Hebrew
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Italian
Japanese
Kannada
Kashmiri
Kazakh
Kirghiz
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Code
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7578
7583
7575
7589
7579
7585
7679
7665
7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Code
7678
7684
7775
7771
7783
7776
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
Language
Quechua
Rhaeto-Romance
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Sindhi
Singhalese
Slovak
Slovenian
Spanish
Sudanese
Swahili
Swedish
Tagalog
Code
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
8373
8375
8376
6983
8385
8387
8386
8476
Language
Tajik
Tamil
Telugu
Thai
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
8471
8465
8469
8472
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Area Codes
Choose an area code from this list.
Area
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
46
Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
Area
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
El Salvador
Ethiopia
Fiji
Finland
France
Germany
Great Britain
Greece
Code
CR
HR
CZ
DK
EC
EG
SV
ET
FJ
FI
FR
DE
GB
GR
Area
Greenland
Hong Kong
Hungary
India
Indonesia
Israel
Italy
Jamaica
Japan
Kenya
Kuwait
Libya
Luxembourg
Malaysia
Code
GL
HK
HU
IN
ID
IL
IT
JM
JP
KE
KW
LY
LU
MY
Area
Maldives
Mexico
Monaco
Mongolia
Morocco
Nepal
Netherlands
Netherlands Antilles
New Zealand
Nigeria
Norway
Oman
Pakistan
Panama
Code
MV
MX
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
PA
Area
Paraguay
Philippines
Poland
Portugal
Romania
Russian Federation
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Code
PY
PH
PL
PT
RO
RU
SA
SN
SG
SK
SI
ZA
KR
ES
Area
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Uganda
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
Zimbabwe
Code
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 47
Troubleshooting
Symptom
Possible Cause
Correction
No power.
• The power cord is disconnected.
• Plug the power cord into the wall outlet securely.
The power is on, but the
player does not work.
• No disc is inserted.
• Insert a disc. (Check the disc indicator in the display window is lit.)
No picture.
• The TV is not set to receive DVD signal output.
• Select the appropriate video input mode on the TV.
• The video cable is not connected securely.
• Connect the video cable securely.
• The selected resolution is not capable with your TV.
• Select another resolution using RESOLUTION button.
• The equipment connected with the audio cable is not
set to receive disc signal output.
• Select the correct input mode of the audio receiver so you
can listen to the sound from the player.
• The power of the equipment connected with the audio
cable is turned off.
• Turn on the equipment connected with the audio cable.
• The [AUDIO] options are set to the wrong position.
• Set the [AUDIO] options to the correct position
(see page 23-24).
• The player is in reverse play, fast forward, slow motion
or pause mode.
• Return to the normal playback.
• The disc is upside down.
• Insert the disc with the playback side down.
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc type and regional
code.)
• The rating level is set.
• Change the rating level.
• The disc was recorded on another unit and was not
finalized.
• Finalize the disc on that unit.
• The Remote Control is not pointed at the remote
sensor on the player.
• Point the Remote Control at the remote sensor of the
player.
• The Remote Control is too far from the player.
• Operate the Remote Control closer to the player.
No sound.
The player does not start
playback.
The Remote Control does
not work properly.
47
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 48
Troubleshooting
Possible Cause
Symptom
Correction
• External USB device is not connected.
• Connect a FAT16 or FAT32 formatted USB device to the
USB port (see page 21).
• The connected USB device does not have enough
space.
• Secure at least 1GB free space in the USB device for
using BD-Live features.
• Internet connection is not established.
• Ensure that the unit is correctly connected to the local area
network and can access the internet (see page 19-20).
• The [BD-LIVE connection] option in the [Setup] menu
is set to [Prohibited].
• Set the [BD-LIVE connection] option to [Permitted].
The YouTube video playback
is often buffering.
• Your broadband speed is not fast enough to play
YouTube videos.
• Contact your Internet Service Provider (ISP) and increase
the broadband speed is recommended.
The YouTube ID is not
automatically stored in the
ID list.
• The ID list is full.
• Delete one of the stored IDs and SignIn with the ID again.
Radio stations cannot be
tuned in.
• The signal strength of the stations is too weak (when
tuning in with automatic tuning).
• Use direct tuning.
BD-Live feature does not
work.
Customer Support
Resetting the unit
You can update the Player using the latest software to enhance the products
operation and/or add new features.
To obtain the latest software for this player (if updates have been made),
please visit http://lgservice.com or contact LG Electronics customer care centre.
Design and specifications are subject to change without notice.
If you observe any of the following symptoms.
• The unit is plugged in, but the power will not turn on or off.
• The front panel display is not working.
• The unit is not operating normally.
You can reset the unit as follows.
• Press and hold the POWER button for at least five seconds. This will
force the player to power off. Press the POWER button again to turn
the player back on.
• Unplug the power cord, wait at least five seconds, and then plug it in
again.
48
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 49
Specifications
System
General
Laser:
Semiconductor laser,
wavelength: 405nm / 650 nm
Signal system:
Standard PAL/NTSC colour TV system
Frequency response:
20 Hz to 20 kHz
(48 kHz, 96 kHz, 192 kHz sampling)
Signal-to-noise ratio:
More than 100 dB
(ANALOG OUT connectors only)
Inputs/Outputs
Harmonic distortion:
Less than 0.008%
VIDEO OUT:
Dynamic range:
More than 95 dB
LAN port:
Ethernet jack x 1, 10BASE-T/100BASE-TX
Power requirements:
Power consumption:
Dimensions (W x H x D):
Net Weight (Approx.):
Operating temperature:
Operating humidity:
AC 110 - 240 V, 50/60 Hz
130 W
Approx. 430 x 76 x 379 mm without foot
4.8 kg
41 °F to 95 °F (5 °C to 35 °C)
5 % to 90 %
1.0 V (p-p), 75 Ω, sync negative,
RCA jack x 1
COMPONENT VIDEO OUT: (Y) 1.0 V (p-p), 75 Ω, sync negative,
RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
HDMI OUT (video/audio):
19 pin (HDMI standard, Type A)
HDMI IN (video/audio):
19 pin (HDMI standard, Type A)
ANALOG AUDIO IN:
2.0 Vrms (1 kHz, 0 dB), 600 Ω,
RCA jack (L, R) x 1
DIGITAL IN (COAXIAL):
0.5 V (p-p), 75 Ω, RCA jack x 1
DIGITAL IN (OPTICAL):
3 V (p-p), Optical jack x 1
PORT. IN:
0.5 Vrms (3.5 stereo jack)
87.5 - 108.0 MHz or 87.50 - 108.00 MHz
522 - 1,710 KHz or 522 - 1,620 KHz or
520 - 1,710 KHz
Amplifier
Stereo mode:
Surround mode:
Type
Front
speaker
2 Way 3speaker
Impedance 4Ω
Rated
Input Power 155 W
Max.
Input power 310 W
Rear
Center
Passive
Speaker
Speaker
Subwoofer
2 Way 3 speaker 2 Way 3 speaker 1 Way 1 speaker
4Ω
4Ω
3Ω
155 W
155 W
225 W
310 W
310 W
450 W
Net Dimensions
(W x H x D) 300 x 1265 x 300 mm 300 x 1265 x 300 mm 370 x 105 x 88 mm
Tuner FM/AM
FM Tuning Range:
AM Tuning Range:
Speakers
155 W + 155 W (4Ω at 1 KHz, THD 10%)
Left+Right: 155 W + 155 W (THD 10%)
Center: 155 W
Surround: 155 W + 155 W
(4Ω at 1 KHz, THD 10%)
Subwoofer: 225 W (3Ω at 30 Hz, THD 10%)
Net Weight 5.0 kg
4.7 kg
1.5 kg
216 x 405 x 360 mm
7.3 kg
Accessories
Speaker cable (6), Remote control (1), Battery (1), HDMI cable (1),
AM antenna (1), FM antenna (1), Video cable (1)
49
HB954TB-AD.BINDLLK_ENG_6445
5/26/09
10:00 AM
Page 50
Open source software notice
The following GPL executables and LGPL libraries used in this product are
subject to the GPL2.0/LGPL2.1 License Agreements:
GPL EXECUTABLES:
Linux kernel 2.6, bash, busybox, dhcpcd, mtd-utils, net-tools, procps, sysutils, tinylogin
LGPL LIBRARIES:
uClibc, DirectFB, iconv, cairo, blowfish, mpg123
LG Electronics offers to provide source code to you on CD-ROM for a
charge covering the cost of performing such distribution, such as the cost
of media, shipping and handling upon e-mail request to LG Electronics at:
opensource@lge.com
This offer is valid for a period of three(3) years from the date of the distribution of this product by LG Electronics.
You can obtain a copy of the GPL, LGPL licenses from
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html and
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
This software is based in part on the work of the Independent JPEG Group
copyright © 1991-1998,
Thomas G. Lane.
This product includes
• Freetype library : Copyright © 2003 The FreeType Project
(www.freetype.org).
• libpng library: Copyright © 2004 Glenn Randers-Pehrson
• Zlib compression library: Copyright © 1995-2002 Jean-loup Gailly and
Mark Adler
• Expat library : copyright © 2006 expat maintainers.
• cryptographic software written by Eric Young (eay@cryptsoft.com).
• software written by Tim Hudson (tjh@cryptsoft.com).
• software developed by the OpenSSL Project for use in the OpenSSL
Toolkit. (http://www.openssl.org)
50
This product includes other open source software.
• Copyright © 1998 by the Massachusetts Institute of Technology.
• Copyright © 2003 Simtec Electronics
• Copyright © 2001 by First Peer, Inc. All rights reserved.
• Copyright © 2001 by Eric Kidd. All rights reserved.
• Copyright © 1996 - 2008, Daniel Stenberg, <daniel@haxx.se>.
• Copyright © David L. Mills 1992-2006
• Copyright © 1998-2003 Daniel Veillard.
• Copyright © 1998, 1999, 2000 Thai Open Source Software Center Ltd.
• Copyright © 1991, 1992, 1993, 1994 by Stichting Mathematisch
Centrum, Amsterdam, The Netherlands.
• Copyright © 1990 The Regents of the University of California.
• Copyright © 1998-2005 The OpenSSL Project.
All rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a
copy of this software and associated documentation files (the “Software”),
to deal in the Software without restriction, including without limitation the
rights to use, copy, modify, merge, publish, distribute, sublicense, and/or
sell copies of the Software, and to permit persons to whom the Software is
furnished to do so, subject to the following conditions:
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
IN THE SOFTWARE.
Download PDF

advertising