LG | LE6016D-NH | LG LE6016D-NH Owner’s Manual

OWNER’S MANUAL
Digital Video Recorder
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LE6016N
LE6016D
P/NO : COV30400919
1105(V1.5)
2
1
Safety Information
Safety Information
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions
in the literature accompanying the
product.
FCC WARNING: This equipment may generate
or use radio frequency energy. Changes or
modifications to this equipment may cause harmful
interference unless the modifications are expressly
approved in the instruction manual. The user could
lose the authority to operate this equipment if an
unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
•
A suitable conduit entries, knock-outs or glands
shall be provided in the cable entries of this
product in the end user.
•
Caution: Danger of explosion if battery is
incorrectly replaced. Replaced only with the
same or equivalent type recommended by
the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
•
Holes in metal, through which insulated wires
pass, shall have smooth well rounded surfaces
or shall be provided with brushings.
This Class A digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe A est
conforme à la norme NMB-003 du Canada.
Warning: Do not install this equipment in a confined
space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance
with the National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio
interference in which case the user may be required
to take adequate measures.
Safety Information
Warning: To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.
Caution: This installation should be made by a
qualified service person and should conform to all
local codes.
Caution: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, should be placed on the
apparatus.
Caution:
This product employs a Laser System. To ensure
proper use of this product, please read this owner’s
manual carefully and retain it for future reference.
Should the unit require maintenance, contact an
authorized service center. Performing controls,
adjustments, or carrying out procedures other than
those specified herein may result in hazardous
radiation exposure. To prevent direct exposure to
laser beam, do not try to open the enclosure. Visible
laser radiation when open. DO NOT STARE INTO
BEAM.
To disconnect power from mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327
AE Almere. The Netherlands
(Tel : +31-(0)36-547-8888)
Disposal of your old appliance
1. When this crossed-out wheeled
bin symbol is attached to a
product it means the product
is covered by the European
Directive 2002/96/EC.
2. All electrical and electronic
products should be disposed of
separately from the municipal
waste stream via designated
collection facilities appointed
by the government or the local
authorities.
3. The correct disposal of
your old appliance will help
prevent potential negative
consequences for the
environment and human health.
4. For more detailed information
about disposal of your old
appliance, please contact
your city office, waste disposal
service or the shop where you
purchased the product.
EEE Compliance with Directive. (for Turkey only)
1
Safety Information
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
LG Electronics hereby declares
that this/these product(s) is/are
in compliance with the essential
requirements and other relevant
provisions of Directive 2004/108/
EC, 2006/95/EC, and 2009/125/EC.
3
4
1
Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
Safety Information
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as powersupply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
Safety Information
•
The purpose of the following safety precaution
is to prevent any unexpected risk or damage
by using the product accurately as intended.
•
Warning
•
Turn off the power of the product before
installing the product. Do not plug many
plugs into one outlet.
--
•
-•
•
When wiping the surface of the product,
do not use water, chemical or detergent,
and always use a dry towel.
--
•
It can cause an electric shock,
problems or scratches to the surface of
the product.
•
It can cause an electric shock or a fire
When unplugging the power, hold the
plug and unplug slowly. Do not hold the
plug with wet hands or plug to a loose
power outlet.
--
It can cause an electric shock or a fire.
It can cause a problem or an injury.
The power outlet must be grounded and
the voltage range must bet within 10% of
the rated voltage. Do not share the power
outlet with hair dryer, iron, refrigerator or
heating device etc.
--
•
It can cause a fire.
Install the product on a location with a flat
surface where it is ventilated well and not
too high.
--
•
It can cause a fire, an electric shock or
an injury.
Install the product in a cool location not
exposed to direct sunlight. Do not install
the product where traffic is high or near
the heating devices.
--
Do not install the product where the level
of humidity, dust or smoke is high.
--
•
It can cause a fire.
It can cause an electric shock or a fire.
Because the cable connected to this device
can be damaged, keep at least 15cm of
clearance between where the product is
installed and where the power outlet is.
--
•
It can cause a fire, an electric shock or
an injury.
Always check for dangerous elements
where the product is installed. If dangerous
elements (Moisture, damaged cable,
unstable installation etc.) are identified,
please contact your nearest service center.
--
•
It can cause a fire, an electric shock or a
product problem.
Do not put any heavy object on top of the
cable or excessively bend the cable.
--
--
It can cause an electric shock or a fire.
Do not put any containers with liquid such
as water, coffee, beverage etc. on top of
the product.
Do not disassemble or reconfigure the
product. Because high level of current
flows on the device, it is dangerous to do
so.
It can cause an explosion.
When replacing the battery, always replace
with the same type of battery as the one
provided. When disposing the battery,
follow the direction of the manufacturer.
--
It can cause an explosion.
1
Safety Information
Please follow the
directions safely use
the product
5
6
Safety Information
•
For old hard drives, you may not be able to
recover the data stored on the drive. When
you use a damaged hard drive, you will
see a sign on the screen saying “Error or
defective”. For the old hard drive, contact
your nearest service center or the original
retailer to replace the hard drive.
1
Safety Information
--
LG Electronics is not responsible for the
data loss from misuse by the user.
Any changes or modifications in
construction of this device which are not
expressly approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.
•
When you install the product near
electronic appliances such as radio or TV,
it can cause problems to the product.
•
Do not disassemble the product unless
done by a technician certified by LG
Electronics.
•
Do not put heavy objects on top of the
product.
•
Be careful not to let alien particles get
inside the product.
--
•
It can cause a problem to the product.
Install the product where it is ventilated
well.
--
Caution
The product at least 15 cm away from
the wall power outlet because the
cable can be damaged.
Please read the following precautions carefully
before installing the product and follow the
directions for installation.
•
Do not install the product at a location
close to a product or broadcast receiver
with strong electric or magnetic wave.
•
Do not install the product where the
level of humidity, dust or smoke is high.
•
Do not put heavy objects on top of the
product.
•
Do not install the product where it is
exposed to direct sunlight or close to the
heating device.
•
Do not install the product where there is
danger of electric shock or near magnetic
object.
•
Do not put objects with high conductivity
on top of the ventilation outlet of the
product.
•
Make sure the power is turned off before
installing the product.
•
Secure sufficient space to connect the
product when installing the product.
•
Do not install the product where it is
not flat, not ventilated well or where
vibration is severe.
-•
-•
It can cause a problem to the product.
Install the product at a flat and stable
location.
The product may not operate normally.
The product at a location with appropriate
level of temperature and humidity.
--
Do not install the product where the
temperature is too high (40 °C or
above) or too low (0° or less).
•
Because the vibration and impact can
damage the product, do not throw any
objects to the location where the product
is installed.
•
Do not install the product where it is
exposed to direct sunlight or close to the
heating device.
Safety Information
•
Firmly fixate the product at a location
where it is well ventilated.
--
The power outlet must be grounded.
•
If you hear any noise or smell any odor
from the product, turn the product off and
contact your nearest service center.
--
•
It can cause a fire or an electric shock.
Periodically have the product checked by
the service center to safety use the product
--
When replacing the battery, always
replace with the same type of battery
as the one provided. When disposing
the battery, follow the direction of the
manufacturer.
--
LG Electronics is not responsible for the
problem from misuse by the user
Do not move or flip the product over while
using the product.
1
Safety Information
It can cause problems to the product
depending on the surrounding
environment. It is recommended to
use the Automatic Voltage Regulator. It
is recommended to wrap wires around
the Ferrite core.
•
•
7
8
Contents
1
Safety Information
4
IMPORTANT SAFETY
INSTRUCTIONS
5
Please follow the directions
safely use the product
15
2-6. Connection and initial
setting
16
RS-485 connection
16
Control port (Output)
connection
17
Sensor (Input) connection
17
About internal hard disk
18
Hard disk installation or
replacement
3
Functional description
22
2
Before use
10
2-1. Product characteristics
11
2-2. Components
11
2-3. Front side
11
LE6016D model
12
LE6016N model
13
2-4. Rear side
14
2-5. Remote Controller
14
How to set the id of remote
controller
3-1. Operation
22
Start Up
23
Shutdown
24
3-2. Monitor Screen
28
3-3. System Setting
28
System
33
Camera
38
Event
42
Network
46
Information
49
3-4. PTZ Control
51
3-5. Search (Playback) &
Backup
9
51
Time search
52
Event Search
54
Backup
4
Web viewer
58
4-1. Installation
58
Web viewer installation
60
4-2. Functional description
60
Web viewer monitoring
window
61
Web viewer search window
62
Search dialog box
63
Saving as AVI file dialog
box
5
70
6-2. Recommended device to
use
70
List of recommended USB
memory
71
Recommended list of CD/
DVD media
72
List of supported PTZ
camera
73
6-3. Initial setting list for factory
default
80
6-4. Product specification
1
2
3
4
5
6
Apple iPhone/iPod
64
5-1. Functional description
64
Real-time monitoring
6
Reference
66
service
6-1. Check before requesting for
10
Before use
2
Before use
2
2-1. Product characteristics
Before use
•
Adopted the stable Embedded Linux
•
Stable file system recovery even after power supply is disconnected from a power outage.
•
Realized small file size and high video quality by applying the H.264.
•
Supports terra byte hard disk (up to 1TB )
•
Supports E-SATA port to use additional external hard disk.
•
Real time recording
•
--
Maximum of 480 IPS@352 X 240 at NTSC
--
Maximum of 400 IPS@352 X 288 at PAL
Supports various recording resolutions and qualities.
--
D1(720x480), Half D1(720x240), CIF(352x240) at NTSC
--
D1(720x576), Half D1(720x288), CIF(352x288) at PAL
--
5 stage recording qualities (Very high, high, normal, low, very low).
•
Easy operation through various user interface and user friendly GUI system.
•
Realized powerful multi-function.
--
•
Real time video display or recording, network transmission and back up can be performed
simultaneously
Easy search functions.
--
Date/Time search (Calendar search), event search
•
Recording before event. (Can be 2~4 seconds).
•
Recording after event. (Can be only up 10 seconds).
•
The operating condition pre-check function according to the change in motion detection and
movement detection
•
Can set recording quality and number of recording frames per seconds.
•
Powerful recording schedule management.
•
Complete synchronization of video/audio.
•
Easy software upgrading through USB storage device or network.
•
Maximum of 5 clients can be connected to 1 DVR at the same time.
Before use
•
Band width setting is automatically set depending on the network speed connected to this
device.
•
Remote alarm notification via e-Mail.
•
PTZ (Pan/Tilt/Zoom) operation.
•
Remote control operation
•
Key board control operation (optional)
•
Supporting Daylight saving
•
Simultaneous output to VGA and BNC
11
2
Before use
2-2. Components
Installation CD
Owner’s Manual
Power cable
Mouse
Remote control
Adapter
SATA cable
HDD power
cable
Screws
Reference: The type of components can be applied differently by the option.
2-3. Front side
LE6016D model
a
b
e
c
d
f g
12
Before use
LE6016N model
There is no built-in DVD recorder at LE6016N model.
b
c
d
2
Before use
a
DVD Recorder: This is used for DVD backup.
b
LED
c
•
Hard disk LED: This is turned on HDD is accessed.
•
Power LED: This is turned on when the power is turned on.
•
Network LED: This is turned on when network is connected.
•
Alarm LED: This is turned on when alarm event occurs.
f g
Navigation buttons
•
At power off status, it is turned on by pressing “OK” button in some seconds.
•
At power on status, instant panic recording is executed by pressing “OK” button in
some seconds.
•
“SEARCH/LIVE” button is used as navigation key, when menu is shown, on the
Chapter 1 Before use other hand, it is used for switching key between SEARCH and
LIVE screen when menu not be shown.
d
MENU/ESC: This is used to open or close menu.
e
OPEN: This is used to open or close the door of DVD recorder.
f
MOUSE: This is used to connect mouse.
g
USB: This is used to connect USB external device.
CAUTION
Mouse should be connected to front side mouse port.
Before use
13
2-4. Rear side
a
b
c
d
2
g
h i j
k
a
Main output port: It is used to connect BNC type monitor. (It outputs the same video as
MAIN output.)
b
Camera video input: These are used to connect cameras.
c
External HDD port: It is used to connect E-SATA HDD.
d
Sensor/Alarm/RS-485 ports - These are used to connect sensor, alarm and RS-485 serial
communication port.
e
USB port: It is used to connect the USB external device.
f
Ethernet port - It is used to connect RJ-45 Ethernet connector. (LAN PORT).
g
VGA port: It is used to connect VGA monitor.
h
Audio input port - It is used to connect audio output port of external device.
i
Audio output port - It is used to connect audio input port of external device.
j
SPOT output port - It is used to connect BNC type monitor.
k
Power connector - It is used to connect Power adapter.
Before use
e f
14
Before use
2-5. Remote Controller
a
b
c
2
Before use
d
f
h
No.
Function
a
Power
This is used to turn on/off the power.
Description
b
Emergency
recording
This is used to start/stop emergency
recording.
c
Number keys
This is used to input channel or values.
d
Plus(+)
This is used to increase setting values.
e
g
i
e
Minus(-)
This is used to decrease setting values.
f
CANCEL
This is used to cancel a job.
j
g
LIVE
h
MENU
k
i
SEARCH
l
m
j
n
o
This is used to display real time screen.
This is used to display menu.
This is used to display screen search.
This is used to navigate each menu
wsad, OK item.
These are used to control playback
(Backward or forward search, play and
pause)
ø
and
buttons have no
function.
k
Play buttons
l
PTZ Menu
This is used to open PTZ Menu.
m
Export backup
This is used to run backup.
ø It can be run in search mode.
n
Split screen
o
This is used for split screen display.
This is used to display channel one by
one.
Auto switching
ø It works as event search at search
mode.
Reference: The shape of remote controller can be different by the model.
How to set the id of remote controller
1. Press cancel button about 3 seconds then light of power button turns on.
2. Enter two digit numbers which is the id of remote controller using number keys.
ø You have to input ‘0’ first when you are to input one digit number.
Ex) In case you want to use ‘2’ as ID, input ‘02’.
3. Every time you press the number key the light of power button will blink.
4. Stopping blinking means that the id is saved.
Before use
15
2-6. Connection and initial setting
Caution
•
The camera or other external devices can be connected to this device in numerous
methods. Refer to the user manual of the camera or other external device for addition
information on connection methods.
•
When installing the camera, check whether the power of the camera is turned off.
•
After installing the monitor, turn on the power of the DVR.
Before use
Connect the BNC type
monitor. (The same
video output as VGA.)
Connect the camera for coaxial
connection.
Connect the
network cable.
Connect USB
device.
Connect the
power adapter.
Connect the BNC
type monitor.
(SPOT output)
Connect the speaker or amplifier.
Connect the audio. (Line input)
Connect VGA monitor.
2
Connect
E-SATA HDD.
16
Before use
RS-485 connection
① This device has 1 data port (RS-485).
② Use this port to connect the PTZ camera or the
keypad. (Optional)
③ PTZ camera / keyboard connection
2
i. Connect the PTZ serial communication cable to
the RS-485 port.
Before use
ii. When connecting the cable, make sure that
the TX- of the device is connected to the RX(TX-) of the camera(keyboard), and TX+ of the
device is connected to the RX+(TX+) of the PTZ
camera(keyboard).
iii. Recommended initial data setting is 9 600 baud
rate, 8 data bits, 1 stop bit and no parity.
iv. When connecting the PTZ camera or keyboard, always change the setting of the DVR
setting menu according the RS-485 setting of the camera, keyboard and this device.
v. Set the same baud rate when you are to use PTZ camera and keyboard at the same time
Control port (Output) connection
①For interface and auto control with the external sensor, the interfacing control output port
(Set value from “Setup Ò Event Ò Sensor/Motion/Video loss” menu) and the “RELAY” port are
connected.
② If the control device (Alarm light, amplified siren, external relay etc.) is “NC (Normal Close)” type,
connect to the control output NC (Normal Close) port.
③ If the control device (Alarm light, amplified siren, external relay etc.) is “NO (Normal Open)” type,
connect to the control output NO (Normal Open) port.
Before use
17
Sensor (Input) connection
Connect one of the signal cables (2 cables) of various
sensors (IR sensor, heat ray detector, magnetic etc.) to the
COM port and connect the remaining signal cable to the
sensor number you want. (Sensor “NC, NO” type can be set
from “Setup Ò Event Ò Sensor” menu.)
Sensor input 1
2
Sensor input 2
3
Sensor input 3
4
Sensor input 4
G
Ground
5
Sensor input 5
6
Sensor input 6
7
Sensor input 7
8
Sensor input 8
G
Ground
NOTE
NC and NO cannot be selected simultaneously.
About internal hard disk
The hard disk installed inside the device is a precision device which can be damaged even with the
small impact. To prevent the hard disk from being damaged, manage the device as follows.
To prevent the data loss, it is recommended to back up any important data into an external storage
device. When installing or uninstalling the hard disk, you must always turn off the power of the
product.
•
If the power is turned on, do not move the device.
•
Do not install this device where it is too hot and humid and where the temperature change is
sudden. It can cause a problem to the device.
•
DO NOT pull out the plug or intercept the power supply while this device’s power is on.
•
When there is a power outage while the power is turned on, some data can be lost.
•
Do not drop the hard drive or put any metallic object, such as coins, inside the device.
•
In case of a power outage while recording, avoid adding, replacing or moving the HDD. The
recorded data can be lost. In this case, turn on the power with the original hard disk that was
used while the power outage occurred. And then add, replace or move the HDD.
•
Because the hard disk is a high precision device, the parts inside the disk can be damaged at
the slightest impact. Please read the following precautions in detail and follow the directions.
--
Do not directly put the hard disk on the desk or table. Because the parts inside the hard
disk can be damaged at the slightest impact, put a thick cushion below the hard disk.
--
If you use the motored driver, the parts inside the hard disk can be damaged from the
vibration.
--
When replacing the hard disk, be careful not to cause any impact to the other parts.
2
Before use
1
18
Before use
-•
Be careful not to cause an impact from the tools and hard disk used for the installation.
Protect the hard disk from static electricity.
CAUTION
This device has elements to cause an electric shock, an accident or a problem to the product.
Also the hard disk may not be recognized or operated properly due to incorrect installation and
setting. Therefore consult with an experienced expert technician when installing the hard disk.
2
Before use
Hard disk installation or replacement
Hard disk installation
After turning on the power of the device, unplug the power from the outlet.
1. Loosen the screw on the left, right and rear side of the
product.
2. Separate the cover of the main unit.
3. Remove the screws on the bracket holding the hard disk,
separate the bracket from the hard disk.
4. Install the hard disk to the bracket and tighten the 4 screws.
d Connecting bracket to hard disk
Set the SATA cable connection port
to lower direction to install the hard
disk to the bracket.
Connect the bracket to hard disk by
tighten the 4 screws.
Before use
19
5. After installing the bracket on the main unit, tighten the screws.
6. Connect the power cable of the hard disk.
7. Connect the SATA cable to the hard disk.
2
Before use
<Connecting power cable>
<Connecting SATA cable>
8. Connect the SATA cable to the SATA port of the main board.
9. Close the cover of the main unit.
10. Tighten the screws.
11. After installing the hard disk, you must format the hard disk from the setting menu.
<LE6016N>
--
<LE6016D>
The first SATA cable port on the main board must be connected at all times. If a hard disk is
not connected, this device may not operate normally.
Hard disk replacement
First turn off the power of the device and then unplug the power.
1. Loosen the screw on the left, right and rear side of the product.
2. Separate the cover of the main unit.
20
Before use
3. After removing all of power/SATA cable connected to hard disk, please separate hard disk
bracket from the body.
4. Loosen the screws on the left and right side of the bracket holding the hard disk.
5. Separate the hard disk from the bracket holding the hard disk.
6. In the reverse order of removing the hard disk, assemble the new hard disk.
7. After replacing the hard disk, turn on the power of the device.
2
8. Reference
Before use
--
Each SATA cable must be connected to the connecting port precisely.
--
Do not vertically put the hard disk in upright position or put other objects on top of the
hard disk.
--
When connecting/disconnecting the hard disk, do not use a motored tool.
--
Refer to the following when adding/replacing the hard disk.
Connecting E-SATA HDD
•
Turn off the power of DVR then connect E-SATA HDD to E-SATA port. And turn on the power of
E-SATA HDD first then turn on the power of DVR.
•
E-SATA HDD is used only for recording, it cannot be used for any other purpose like backup, for
example.
Recommended list of hard disk
Hard disks of below are the ones proved to be compatible through experiment.
Please refer to when adding or replacing the hard disk.
Capacity
250 GB
LE6016
ST3250310CS
ST3250312CS
500 GB
ST3500312CS
1 TB
ST3100322CS
Seagate
CAUTION
When you select the hard drive in use for resetting, the video data saved previously will be
deleted. Therefore you must be careful.
Before use
21
Database recovery of the HDD
•
The system has the check process of the database condition during the system booting. If
there is some problem, the system will be displayed the confirmation window to recover the
database.
•
Recovery time of the database is proportional to the amount of data.
•
Recovery time takes more than 16 times if database recover included event data.
•
Basically, the recorded data is not damaged because it always make the backup data.
Arrangement of the database on the HDD
The system will be displayed the confrimation window to arrange the database at the reboot
time every 6 month when you use the device normal. If you do not database arrangement, the
system will perform the database arrangement every 12 month at booting point.
Check the HDD problem
•
If you install the hard disk first time, or do the Initialization, or shut down equipment
abnormally more than three times consecutively, the system checks integrity of the hard disk
when booting.
•
The system will be random check the bad sector on the hard disk.
2
Before use
•
22
Functional description
3
Functional description
3-1. Operation
Start Up
3
1. Turn on this device, then it boots with power indicator light turned on.
Functional description
2. After booting it will be displayed as the LOGOUT id.
3. Pressing
button, then the login window would be displayed. Select user and press “OK”
button to continue.
ZZ [USER]
You may select user to login and authority is restricted by kind of user. The access rights
can be set for each user.
1) admin for system administrator (Access rights to Live, Search and Setup)
2) user1/user2/user3 for general user (Access rights can be set by administrator)
Functional description
23
ZZ [password]
The default user and password are set to
‘admin’ and ‘000000’ as shown above. Click
password input area, you will see the screen
keypad as right.
4. Input password by using virtual keypad on screen.
5. Click “OK” button to execute DVR system and you will see live screen.
Shutdown
button, then logout window will be displayed as below.
ZZ Selection: Select the Log Out or EXIT.
ZZ USER : Display current user has logged. (admin/user1/user2/user3)
ZZ PASSWORD : Input password.
2. Click “OK” button to “Log Out” or “DVR Shutdown”.
Functional description
1. While the status is logged in, press
3
24
Functional description
3-2. Monitor Screen
B
A
C
D
3
Functional description
E
A [Camera name]
•
Shows camera name
•
If you want to modify camera name, you can do so by selecting [Setup] Ò [Camera]Ò
[Channel]
B[Status icon] (OSD)
•
Status icon shows current status of camera/recording.
•
(OSD Feature)
Item
Icon
Description
Item
Audio Icon
Camera
Recording
Continuous
Recording
Description
Immediate Recording
Motion Icon
PTZ Icon
Icon
Recording by Motion
Recording
Non Recording
Recording by Sensor
Functional description
25
C [Channel selection]
•
Selected channel shows green rectangle on the edge of the screen.
D [Live view]
•
It shows current live view as real time.
E [System control toolbar]
a
b
c
d e
f
g
h ijklmnop
q r
s
tu
•
It shows current connection status of network.
(Black : It shows disconnected status.)
(Blue : It shows connected status.)
•
If you want to modify network settings, you can do so by selecting [Setup] Ò
[Network] Ò [TCP/IP]
b [Current Date/Time]
•
Current date and time is displayed.
•
If you want to modify date and time, you can do so by selecting [Setup] Ò [System]
Ò [Date]
c [Setup]
•
Set the system environment and function.
•
Refer to Chapter “3-3. System Setting”.
d [Live screen]
•
This is the button to switch over to the live display window to view the realtime
video screen.
e[Search]
•
This is the button to switch over to the search window to view the recorded screen.
•
Refer to Chapter “3-5. Search (Playback) & Backup”
f[PTZ control]
•
This is the button to control the PTZ camera
•
Refer to Chapter “3-4. PTZ Control”.
Functional description
a [Network status display]
3
26
Functional description
g [Divided screen selection]
•
1/4/9/13/16 divided screen can be displayed in live view.
h [Auto sequential]
•
Click
•
This function does not work at 16 divided screen.
•
You can set the switching interval at [Setup] Ò [System] Ò [Overview] Ò
[Auto- switching].
button and each channel will be switched automatically.
i [Logout]
•
Use Lock menu to change user or lock system operation.
j [Relay out off(Alarm off )]
3
Functional description
•
When alarm (relay out) is on by event, you can stop the alarm with it.
•
Press
•
If next event occurs after alarm (relay out), the alarm will start again.
button to stop alarm (relay out).
k [Stop]
•
Click this button to stop playback recorded data.
l [Reverse frame by frame playback]
•
Click this button to search the data with reverse frame by frame playback.
m [Fast backward playback]
•
Click this button to playback fast backward. The speed of fast backward playback
can be set to one of the following, X2, X4, X8, and X16.
n [Forward playback]
•
Click this button to playback forward as normal speed.
•
Live screen can be switched to playback instantly by clicking this button.
o [Fast forward playback]
•
Click this button to playback fast forward. The speed of fast forward playback can
be set to one of the following, X2, X4, X8, and X16.
p [Forward frame by frame playback]
•
Click this button to search the data with forward frame by frame playback.
q [System Log]
•
This shows the system log in DVR.
•
Click
button to show the system log list.
Functional description
27
3
You can see the log of previous date or next date by using a/d button.
•
You can see the previous or next log list by using ( - ) / ( + ) button.
•
Click “OK” button to close window.
•
Clicking
button at search mode, Event search dialog box will be shown. Refer
to “Event search”.
r [Information]
•
It shows the system information.
s [Playback status]
•
It shows the playback status.
t [Bookmark]
•
You can add playback position (date/time) to access immediately later.
u [Backup]
•
Click this button to run backup recorded data.
•
Refer to Chapter “3-5 Search (Playback) & Backup”.
NOTE
•
You can show or hide system control bar by double clicking right mouse button.
•
If the HDD has a some bad sector, the HDD information will be displayed on right top of the
screen.
Functional description
•
28
Functional description
3-3. System Setting
System setting can be configured by setup menu. Working condition can be specified by front
button / mouse / remote controller.
Only admin user can setup system configuration by menu.
System
A
3
Functional description
B
C
D
E
A [Overview]
•
You can specify the system configuration by this menu.
•
Use a / d button to change configuration.
Functional description
29
ZZ REMOTE ID: ID can be selected from 00 to 99.
ZZ DE-INTERLACE: Enable or disable de-interlace feature for playback screen. De-interlace
feature is only available for ‘D1’ resolution.
ZZ AUTO SWITCHING : Set dwell time when auto switching function is working. (1 Sec ~
30 Sec)
ZZ SPOT-DIVISION: Set the division mode for SPOU OUT screen.
ZZ SPOT-OUT : Select spot channel. (channel 1~16, AUTO). If you select “AUTO”, Spot will be
changed sequentially.
ø When spot channel is changed automatically, dwell time that specified by Spot
from AUTO SWITCHING is applied.
ZZ BUTTON BUZZER : Select button buzzer on / off.
ZZ LANGUAGE : Select language.
ZZ USE DATA RETAIN : data saving period can be set from 1 day to 60 days.
B [Date/Time]
•
Specify date and time of system.
•
You can specify setting by using a / d button
•
Select date and time, then you will see virtual keypad as below.
ZZ DATE : Specify current date
ZZ TIME : Specify current time
3
Functional description
ZZ OVERWRITE: If you select “ON”, when recording space of HDD is exhausted, it overwrites
on the oldest recorded data to continue recording.
30
Functional description
ZZ LOCALE : Specify locale of country.
If you click
button, the time zone dialog box will be shown as below, and
select a time zone, then click OK to change setting.
3
Functional description
ZZ NTP SERVER : It is used to set internet time server.
ø Daylight saving time is applied automatically according to corresponding
location.
C [Password]
•
You can specify password and authority of each user.
•
The password can be set max 20 digits.
•
You can set authority for each camera, setup, search/backup, and PTZ control for each user.
•
You can set the system log out automatically. If there is no operate during the selected
time, the system will log out automatically.
Functional description
31
ø If you access as Admin account, previous password is not required.
ø No authority setting is available for Admin account.
ø Only camera authority is allowed for Logout account.
ø Logout screen setting is applied as the same for Spot-Out.
ø White screen will be shown for the cameras which are not set the authority.
D [Initialize]
•
You can initialize data and configuration by this menu.
3
•
The dialog box will be shown as below at the first booting after factory default
setting.
•
The text in the dialog box will be shown in English as default.
ø You can set time zone by clicking SET button, and which is the same as [SYSTEM]
Ò [DATE/TIME] menu.
ZZ LOG : Delete all event log.
ZZ SETTING : Delete setting of configuration.
ZZ HDD : Format HDD data.
Functional description
ZZ FACTORY : Delete entire data in the system and restore as factory default.
32
Functional description
NOTE
•
If data is initialized, it can’t be recovered. Before use “initialize”, important data must be
backup.
•
HDD Factory initialization makes format HDD and you will loose recorded data
E [Controller]
•
Connect keyboard controller to DVR system.
•
Setup configuration to access DVR with keyboard controller.
(*Refer to controller user manual)
3
Functional description
ø Supported device : LKD1000 Dynamic Controller (LG)
Functional description
33
Camera
On the camera menu, channel, recording, schedule, color and PTZ can be configured.
A
B
C
D
E
•
You can specify channel name and audio for each camera.
ZZ CAMERA : Select camera to change
ZZ CHANNEL NAME : Input channel name (Max 8 digits)
ZZ AUDIO : Specify channel that audio is related.
Functional description
A [Channel]
3
34
Functional description
B [Recording]
•
You can specify recording configuration.
3
Functional description
ZZ TOTAL FRAME : Max frame rate has restricted by screen resolution.
ZZ CAMERA : Select camera to set frame and quality.
ZZ RESOLUTION : Specify screen resolution. (CIF / HALF D1 / D1 )
ZZ FRAME : You can specify recording frame rate when recording method is continuous
for selected camera.
ø Frame rate cannot exceed event frame rate.
ZZ EVENT FRAME : You can specify recording frame rate when recording method is event
for selected camera.
ZZ QUALITY : Specify image quality for selected camera.
(VERY HIGH, HIGH, NORMAL, LOW, VERY LOW)
ZZ Click “APPLY ALL” button to apply setting to all cameras.
Functional description
35
C [Schedule]
•
You can specify recording method by schedule with date and time.
3
ZZ Click channel number to change recording method for all time.
ZZ Click time label to change recording method for all channel.
ZZ Click “COPY” button to copy the settings for applying the current settings to the other
channel(s).
C : Continuous recording method
H : Continuous recording + event recording method (Motion, Sensor)
E : Event recording method: if event (Motion, Sensor) happens, recording works.
N : No Recording.
ZZ Click ‘HOLIDAY’ button to specify holidays.
Functional description
ZZ Click time table to change recoding method.
36
Functional description
--
You can select month and day by clicking date button.
--
Click the Add button, the selected month and day will be added to the list of
holidays.
--
Click the Delete button to delete the selected date from list.
D [Color]
•
You can adjust brightness, contrast, saturation and hue.
3
Functional description
E [PTZ]
•
This is to setup the PTZ configuration.
ZZ CAMERA : select camera to setup PTZ.
ZZ DEVICE NAME : Select camera name.(Max 15 cameras supported)
1. LG Multix_E / LG Co.,Ltd
2. LG Multix / LG Co.,Ltd
3. LPT - A100L / LG Co.,Ltd
4. LVC-C100 / C200HM / LG Electric Inc
Functional description
37
5. HSDN251 / Honeywell Co.,Ltd
6. MD200 / 2000 / 1200 / 800 / Sony Co.,Ltd
7. New Born / NEW BORN HIGHTECH
8. WVCS850 / Panasonic
9. PELCO-D / PELCO Co.,Ltd
10. PELCO-P / PELCO Co.,Ltd
11. SAMSUNG_E / SAMSUNG Co.,Ltd
12. SPD-2300 / 3000 / 3300 / SAMSUNG Co.,Ltd
13. SUNGJIN / SUNGJIN Co.,Ltd
14. TPD7720 / DYNACOLOR,INC
15. V1305R-DC / V1300RB / CRX - 1013 / VICON
ZZ DEVICE ID : Select ID that configured in camera.
ZZ TOURING INTERVAL : This is time interval before moving to next preset position when
touring.
•
Select one from 5 seconds, 10 seconds, 20 seconds, 30 seconds, 1 minute, 3
minutes and 5 minutes.
•
The default is 1minute.
NOTE
Basically, DVR supports one RS-485 port for PTZ connection.
3
Functional description
ZZ BPS : Bit rate Per Second for data transmission.
Default value of BPS is 9600
ø Value can be selected by camera setting: (1200/ 2400/ 4800/ 9600/ 19200/ 38400/
57600/ 115200 bps)
38
Functional description
Event
You can specify the processing when event occurs like sensor, motion detection, video loss, and
the email notification settings when event occurs.
A
B
C
D
3
Functional description
A [Sensor]
•
You can specify the processing when event occurs from input device.
ZZ SENSOR : Selecting sensor number. ( 1 ~ 8 )
ZZ TYPE : Setting NO / NC type.
•
NO (Normal Open) : The type of input device is opened normally.
•
NC (Normal Close) : The type of output device is closed normally.
Functional description
39
ZZ CHANNEL : Selecting associated channel with the sensor input. (OFF/1~16)
ZZ ALARM : Setting alarm out when event occurs from input device.(OFF/1~4)
ZZ ALERT : Setting sound a buzzer when event occurs from input device. (ON/OFF)
ZZ SPOT-OUT : Setting spot out when event occurs from input device.(ON/OFF)
ZZ DURATION : Setting the duration time from event occurs. ( 1~10 Sec., OFF)
B [Motion detection]
•
You can specify the process when motion is detected.
3
Functional description
ZZ CHANNEL : Selecting camera which is associated event.
ZZ MOTION ZONE : Setting the motion detection zone.
--
Click “SET” button to setting motion detection zone.
--
The red-marked area is set as motion detection zone.
--
Click right button of mouse on the screen to display menu window.
40
Functional description
>> SELECT ALL : Selecting entire area.
3
Functional description
>> UNSELECT ALL : Unselecting entire area.
>> SAVE : Saving selected area as a motion detection zone.
>> EXIT : Exiting motion zone setting.
ZZ SENSITIVITY : Setting the motion sensitivity. (1 to 10)
ZZ ALARM : Setting alarm out when motion is detected.
ZZ ALERT : Setting sound a buzzer when motion is detected.
ZZ SPOT-OUT : Setting spot out when motion is detected.
ZZ DURATION : Setting the duration time from motion detection occurs.
C [Video loss]
•
You can specify the processing when video loss.
ZZ CHANNEL : Selecting camera which is associated event. (1~16)
ZZ ALARM : Setting alarm out when video loss. (OFF/1~4)
Functional description
41
ZZ ALERT : Setting sound a buzzer when video loss. (ON/OFF)
ZZ DURATION : Setting duration time from video loss. (OFF/1~10 Sec.)
D [E-mail]
•
You can set the E-mail notification when event occurs.
3
ZZ SMTP SERVER : Setting the IP address or domain name of SMTP server.
ZZ PORT : Setting the TCP port number of SMTP (Default value is 25).
ZZ ACCOUNT : Setting the E-mail account registered in SMPT server.
ZZ PASSWORD : Setting the password of the E-mail account.
ZZ SENDER : Setting the E-mail address of sender.
ZZ RECEIVER : Setting the E-mail address of receiver.
ZZ E-MAIL TEST : Click to send testing E-mail, then RECEIVER can check the testing E-mail.
<Success>
<Failure>
ø SMTP server does not support encrypted E-mail protocol.
Functional description
ZZ MODE : Enabling or disabling E-mail notification. (OFF / Authentication / Not
authentication)
42
Functional description
Network
You can set the network environments.
A
B
C
D
3
Functional description
E
A [TCP/IP]
•
You can specify the TCP/IP setting according to network environment.
•
Specifying the TCP port number of Web, Playback and Live.
•
Default values: Web(80), Playback(9091), Live(9092)
For dynamic IP or PPPoE
•
All the items of IP address, subnet mask, gateway and DNS are disabled and set
each value automatically.
•
You can specify account and password of PPPoE using PPPoE button which is
located left below.
Functional description
43
For static IP
ZZ IP ADDRESS : Enter IP address received from ISP using screen keyboard.
ZZ SUBNET MASK : Enter subnet mask received from ISP using screen keyboard.
ZZ GATEWAY : Enter gateway received from ISP using screen keyboard.
ZZ DNS : Enter the DNS IP address received from ISP using screen keyboard.
ZZ MAC ADDRESS : This is hardware specific unique address of network device, so user
cannot set this value.
ø 8000~65535 port number is recommended.
B [Streaming]
•
You can set each item about the network video streaming.
ZZ TOTAL FRAME: : Total frame rate set / Maximum available frame rate
ZZ CAMERA: Selecting camera.
ZZ FRAME: Frame rate per a second for each camera
ZZ QUALITY: Selecting video encoding quality (VERY HIGH, HIGH, NORMAL, LOW, VERY
LOW)
ZZ Click “ APPLY ALL ” button to apply setting to all cameras.
3
Functional description
ø Do not use the same port number with each other.
web(80),playback(9091),live(9092),CMS LG(9100)
ø If the network of DVR is connected via router, you must set Configuration of port
forwarding according to the router.
(web, search, live ports) Please refer to user’s guide of the router which you are
using.
44
Functional description
C [DDNS]
•
You can use DDNS service provided by LG.
•
You can connect to DVR easily using host name instead of IP address with LG DDNS
3
Functional description
ZZ MODE : Enabling or disabling DDNS.
ZZ SERVER : IP address of DDNS.
ZZ PORT : TCP port number of DDNS.
ZZ DOMAIN : The domain name of DVR device.
ZZ INTERVAL : Setting the interval of IP address updating.
D [CMS]
•
Specifying IP address and TCP port number of CMS.
ZZ MODE : Enabling or disabling event report to the central monitoring center when
event occurs.
ZZ IP ADDRESS : The IP address of the central monitoring center.
Functional description
45
ZZ PORT : The TCP port number of the central monitoring center.
ø 8000~65535 port number is recommended.
ø Do not use the same port number with each other.
web(80), playback(9091), live(9092), CMS LG(9100)
E [Event filter]
•
Specifying the event which will be sent to the central monitoring center and E-mail.
3
ZZ SHUTDOWN : Enabling or disabling the system shutdown event.
ZZ SETTING CHANGE : Enabling or disabling the setting change event.
ZZ LOGIN / LOGOUT : Enabling or disabling the login / logout event.
ZZ SENSOR DETECTION : Enabling or disabling the sensor detection event.
ZZ MOTION DETECTION : Enabling or disabling the motion detection event.
ZZ VIDEO LOSS : Enabling or disabling the video loss event.
ZZ ALARM OUTPUT : Enabling or disabling the alarm output event.
Functional description
ZZ SYSTEM START : Enabling or disabling the system start event.
46
Functional description
Information
You can view the general system information and run software update.
A
B
C
D
3
Functional description
A [System information]
•
You can view the system information.
ZZ MODEL : Model name of the device.
ZZ IP ADDRESS : The IP address assigned to the device.
ZZ MAC ADDRESS : The MAC address assigned to the device.
ZZ F/W VERSION : The version number of firmware.
ZZ OS VERSION : The version number of Operating system.
Functional description
47
ZZ VIDEO TYPE : Showing NTSC or PAL. This is set automatically by detecting incoming
video signal, so user cannot change this value.
ZZ HDD: HDD capacity, using ratio and status.
--
* mark is shown at the HDD which is currently recording.
--
“NOT HEALTHY” is shown according to the HDD status.
--
The HDD connected to E-SATA port is displayed as “External HDD”.
B [System log]
•
You can view the system log. (Refer to page 26 [System log])
C [F/W Update]
•
You can run firmware update.
3
Functional description
ZZ FILE : You can specify the firmware file to update using a / d buttons.
48
Functional description
D [Setting update]
3
Functional description
ZZ IMPORT: You can replace current setting values with new values from USB memory.
(ENABLE/DISABLE)
ZZ EXPORT: You can export current setting values to USB memory. (ENABLE/DISABLE)
NOTE
USB memory stick is needed to update F/W or settings.
It takes about 5 seconds to recognize USB memory device after connected.
“USB is not detected.” Message will be shown when you are to run backup without
connected USB.
Functional description
49
3-4. PTZ Control
It is used to control PTZ camera which is connected at RS-485 port. Settings of camera and DVR
should be done if you are to control PTZ camera.
1. Click the icon
to control PTZ.
2. Control the PTZ camera using each item below.
a
b
c
d
3
f
g
h
i
j
k
l
m
n
o
a Click to move the PTZ control window.
bClick this button to close the PTZ control window.
cClick this spin control to select PTZ camera. (1~16)
dClick this spin control to specify the moving speed of PTZ camera (1~6).
eClick this button to show the OSD menu of camera.
fClick these direction buttons to pan or tilt camera.
gClick to control zoom in or out.
Functional description
e
50
Functional description
hClick to control the focus of camera manually.
iClick to control the iris of camera manually.
jClick to select preset number.
kClick to move to selected preset position.
lClick to set current position as a new preset position.
mClick to delete specified preset number.
nClick to start touring, which function traverse each preset position one by one according to
dwell time.
oClick to stop touring.
3
ZZ Setting a new preset position
Functional description
1. Move camera position using direction button f.
2. Select the preset number to set using button j.
3. Click button l “SET”.
4. Repeat process 1 ~ 3 stage to set another preset position.
ø Preset numbers are available up to 10.
ø The maximum preset number is different according to the specification of camera.
ZZ Moving camera to preset position
1. Select the preset number to move using button j.
2. Click button k “GO”.
ø Moving camera to preset position is only available when the camera supports
preset feature.
ZZ Deleting preset position
1. Select the preset number to delete using preset number button j.
2. Click button m “CLEAR”.
ø Deleting preset position is only available when the camera supports.
ZZ Starting touring
1. Click button n “START”.
2. Then it will start traversing each preset position one by one automatically.
ZZ Stopping touring
1. Click button o “STOP”.
2. Then it will stop traversing.
Functional description
51
NOTE
•
The tour which is working will be stop after the setting is changed.
•
If you control the Camera OSD by using the SAMSUNG E protocol to select the exit(X)
menu, the DVR may not opreate normally. In this case, you can recover the system as
input the Zoom +/- key after input O key of the OSD.
3-5. Search (Playback) & Backup
Various features are available for user to search recorded data easily.
You can search recorded data with date and time.
ZZ Search method
A. Click
button on menu bar of real time screen.
B. Select the date you want to search on the calendar above and click “OK”.
(The date with recorded data is displayed in bold.)
C. Then recorded time table will be displayed. (Refer to the image below)
D. The recorded data will be displayed after you select time and click “OK” button.
Functional description
Time search
3
52
3
Functional description
Functional description
ø Click the “CANCEL” button to select date again.
ø You can select a data if data are duplicated at the same time stamp using spin
box below. The spin box is shown only when data are duplicated at the same time
stamp, which is caused when daylight saving period.
ø Bigger number of duplicated data stands for more recent data.
Event Search
You can search recorded data using event occurrence time.
A. Click mouse on the icon
of the menu bar which is located in the lower position of the
search mode screen.
B. Use ad buttons on the upper right side to select camera to search.
C. Check sensor, motion check box below to filter out the events.
D. Move to previous or next page using – and + buttons.
Functional description
53
E. Select a data to search from the list. Click the mouse button to move to the corresponding
recorded data.
F. Click “PLAY” button and the searched data will be played.
Bookmark
You can access the bookmarked time directly without going through the search.
3
1. Use the time search and place you want to add a bookmark.
2. Click mouse on the icon.
3. If you want to add the current selected time, click Add button.
Bookmarks can be added up to 100.
ZZ SEARCH
1. Click mouse on the icon.
2. “+” and “-“ button to move the page using a bookmark and then select the item you want
to move to
ZZ DELETE
1. Click mouse on the icon.
2. After you select an item, click the Delete button to delete it.
If you want to delete the entire entry, click DELETE ALL.
Functional description
ZZ ADD
54
Functional description
Backup
You can back up the recorded data which you select date/time and channels.
3
Functional description
A. Click mouse on the icon
of the menu bar which is located in the lower position of
the screen.
B. Select a device to backup data will be stored. Only USB-STICK is available for LE6016N.
USB-STICK, CD-RW, or DVD-RW can be used for LE6016D.
C. Select media type. If you select FILESYSTEM, backup data will be stored as native format
with backup player. If you select AVI, only one channel is backup
D. If you select the camera you want to perform a backup, click “SET” button and select
cameras you want. On the other hand, when AVI is selected, only one camera can be
selected.
E. It displays selected cameras. (CAMERA : 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16)
F. Specify starting date/time of backup period.
G. Specify ending date/time of backup period.
H. Check the data size to backup. But, when AVI is selected, only one camera can be
selected.
I. If duplicated data exists in the backup data period, select one data from “START
DUPLICATED DATA” or “END DUPLICATED DATA”.
J. After finishing setting for backup, click OK button.
K. When backup is started, the screen moves from search to real time live mode and the
icon and text will be shown as below to display backup progress.
It shows on backup.
It shows the progress of backup.
“AVI” is displayed when AVI backup mode is
activated.,
Functional description
55
L. The message “BACKUP STOP” will be shown when backup is finished.
•
You can backup automatically daily based by schedule backup.
3
B. Enter the time to execute backup at “BACKUP TIME”. If USB memory stick is not
connected nor has no free space, backup cannot be executed.
C. Enter start time of backup period at “START BACKUP”. Check “USING A PREVIOUS DATE” if
needed.
D. Enter end time of backup period at “END BACKUP”. Check “USING A PREVIOUS DATE” if
needed.
E. If you want to select cameras to backup, Click “SET” button at “CAMERA” and then select
cameras. On the other hand, In case of AVI backup, only one camera can be used.
F. Selected cameras are shown. (CAMERA : 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16)
G. Select data format. When selecting “FILESYSTEM”, native backup player is included as
well. So you can search and playback easily with it.
H. Click “OK” button after finishing settings. When the set time at “BACKUP TIME”, the
backup will be executed automatically.
ø Schedule backup will be executed repeatedly once a day.
Functional description
A. If you are to use schedule backup, set “USE SCHEDULE” to “ON”.
56
Functional description
How to cancel backup
If you press
ÄÄ
button when backup is running, the selection message will be
shown as below.
Click “OK” button to cancel backup.
ÄÄ
3
Functional description
MEDIA ERASE
You can erase data in the storage media, like USB memory stick, CD-RW or DVD-RW.
ÄÄ
When you are to use USB memory stick, after connecting USB storage to USB port
ÄÄ
of front side, click “MEDIA ERASE” button to erase data.
It is recommended to backup important data stored in USB storage before using
ÄÄ
this function.
When you are to use CD-RW or DVD-RW, after inserting media to DVD recorder, click
ÄÄ
“MEDIA ERASE” button to erase data.
ø The backup process is not started if you specify invalid starting and ending
date/time.
ø The backup period cannot exceed 24 hours.
ø The USB memory stick should be formatted as FAT32.
ø When AVI backup, if there are different resolution or frame rate exist, the AVI
files are separated at each changed position.
ø Maximum size of backup data is depends on the storage media to be used. In
case of USB memory stick, only free space is used. (But, in case of AVI backup,
the maximum file size is limited to 2GB.), up to 700MB for CD-RW, and up to
4.7GB for DVD-RW.
ø In case of FILE-SYSTEM backup, data files are separated as 127MB unit, in the
other hand, single file is used for AVI backup.
ø If data contained at CD-RW or DVD-RW media, old data are removed and new
data will be written.
ø If there’s duplicated data at the same time stamp, you can select specific data
position with the dialog box as below. Select data position with spin box, and
then click “OK” button to start back up. The older data is the smaller number.
ø The other functions do not work when backup is running.
Functional description
57
ø Bigger number of duplicated data stands for more recent data.
NOTE
Do not remove the external USB device when backup is running.
•
Backup data playback
The backup data in USB storage or CD/DVD media can be played at PC.
3
Functional description
<Selecting backup folder in USB storage>
<Selecting CD/DVD drive >
A. The backup player software will run automatically when you insert the media
containing backup data at the PC. If backup player is not run automatically, according
to security settings of PC, you should run it manually. In case of USB storage, it is
located at “\player\player.exe”, and in case of CD/DVD, it located at “\player.exe”.
B. Specify the folder containing backup data. In case of USB storage, the name of folder
consists of fs-[backup date/time], and in case of CD/DVD, just select disk driver.
C. After specifying data folder, click “OK” button, then backup data will be played.
•
The system log backup
The system log information will be saved by the text file format in the backup data folder.
When the backup is progress, the system log is saved from backup start date/time to
backup end date/time at the same time.
58
Web viewer
4
Web viewer
4-1. Installation
Set up the network before the installation.
Web viewer installation
1. Enter the LG DVR IP address in the Web address window, and then the following Active X
installation window will be displayed.
4
Web viewer
2. When you click on the Active X install button, the following window will be displayed. Press the
Install button.
Web viewer
59
3. Press the Next button from the Web View installation window. When the installation is
completed, the Web initialization screen will be displayed. (General installation recommended)
4
NOTE
Web Viewer and CMS LG cannot be used at the same time.
Web viewer
4. Enter the ID and password. (Multi-login is not enabled for admin user ID.)
(Default: admin, user1, user2, user3)
60
Web viewer
4-2. Functional description
Web viewer monitoring window
A
B
C
D
E
F
I
G
H
J
K
4
Web viewer
L
M
N
A
Divide screen division (Full screen/1/4/9/16)
B
Selecting a camera
C
Real time image capture (Save as JPEG)
D
Settings (It is available only when you logged in as admin)
E
Enable or disable incoming audio (Default value is disable.)
F
Zoom control
G
Iris control
H
Focus control
I
Preset (Click “Go” button after selecting preset number at combo box)
J
Start/Stop touring (Rotation between each preset positions)
K
Pan tilt control (Up, down, left and right buttons)
L
Controlling moving speed when pan tilt operation
M
Switching to search window
N
Logout
ø
Preset and touring are available after preset is set on the device.
Web viewer
61
Web viewer search window
A
B
C
D
E
I
H
F
G
J
4
A
B
C
D
E
F
G
H
I
J
K
L
Divide screen division (Full screen/1/4/9/16)
Selecting a camera
Saving video or still image (Saving as AVI/JPEG/BMP)
Date/Time selection button to play back (Refer to “Search dialog box”)
Enable or disable incoming audio (Default value is disabled.)
Pause button
Forward play button
Backward play button (Displaying only key-frame)
Fast forward play button
Fast backward play button
Switching to monitor window
Logout
Web viewer
K
L
62
Web viewer
Search dialog box
A
B
E
C
D
F
H
4
G
Web viewer
A
Recorded data graph (Click on the data graph to select time to play.)
B
Time scroll bar
C
Zoon in/out of graph (It can be scaled from 2 hours to 24 hours by minute unit.)
D
Displaying selected data/time
E
Displaying calendar (The dates are shown in bold if recorded data exist.)
F
Description of the color of the recorded data graph
G
“OK” button (Video is played immediately when you selected data/time which has
recorded data.)
H
Progress bar which shows loading progress.
Web viewer
63
Saving as AVI file dialog box
A
B
C
D
E
F
H
G
I
A
Camera name/Date/Time which is currently displayed.
B
Starting AVI saving (File name is requested when you click on this button.)
C
Stopping AVI saving
D
Closing Save as AVI dialog box (It will be closed automatically after stopping AVI file if it is
being saved.)
E
Specifying time period to save AVI file.
F
Starting time to save AVI file.
G
Stopping time to save AVI file.
H
Starting periodic AVI file saving
I
Closing after finishing AVI file saving.
J
Increasing AVI saving speed with reducing displaying frame rate.
Web viewer
J
4
64
Apple iPhone/iPod
5
Apple iPhone/iPod
5-1. Functional description
Real-time monitoring
If you can use Wi-Fi environments, you can view the real-time monitoring video from DVR with
iPhone/iPod.
1. Run web browser at iPhone/iPod, and enter LG DVR IP address.
5
Apple iPhone/iPod
2. Enter id and password, and click “login” button the real-time monitoring screen will be shown.
Apple iPhone/iPod
65
3. Real-time monitoring screen.
5
B
A
Camera selection (CH1~16)
B
Video screen
Apple iPhone/iPod
A
66
Reference
6
Reference
6-1. Check before requesting for service
If the following symptoms are observed when using the product, recheck the following. It may not
be a problem.
Symptom
Checkpoint and resolution
Check whether the power plug is correctly plugged.
I cannot turn on the power
of the device
Check whether the voltage of the power supply is correct.
If the power cannot be turned even when the power of the
device is connected correctly, please contact your closest service
center
Check whether the power plug is correctly plugged.
Check whether the monitor is turned on.
The power of the device is
turned on, but the screen on
the monitor is not turned on
Check whether the video cable between the monitor and device
is connected correctly.
Check the selected monitor type.
Try disconnecting the power plug, and then plugging it again.
Check whether the video output port of the camera is correctly
connected to the device.
6
Reference
Camera number is displayed
on the screen but the
video of the camera is not
displayed
Check whether the power supply of the camera is connected
correctly.
Check whether the resolution is set to 1024x768 in VGA
environment setting.
Check if there is any issue with the video cable between the
device and the camera.
Reboot this device.
Reference
Symptom
67
Checkpoint and resolution
Check the recording setting from the recording setting menu.
Video of camera is displayed
on the screen but I cannot
record the video through the
device
Check whether the hard disk is recognized from the system
information window.
If the hard disk is not recognized normally, check the format and
connected condition of the hard disk.
Check the available space on the hard disk.
During the search, check whether the video data currently being
recorded exists.
I cannot search the recorded
video.
If the video data currently being recorded does not exist, check
the recording setting of the menu.
Check whether the hard disk is recognized from the system
information window.
If the hard disk is not recognized normally, check the format and
connected condition of the hard disk.
Check whether the recording audio channel is correctly set up.
I cannot hear the audio
recorded with the video.
Check whether the connecter on the rear side of the device is
connected with external device (Line input) correctly.
Check whether the connected external device is operating
correctly.
Check whether the video format of the device is the same as
that of the camera.
The video format can differ by the region into PAL or NTSC
format. IF the video format of the device is not the same as that
of the camera, the video may not be recognized.
6
Reference
Screen colors of some
cameras are incorrect or
the video is displayed in
abnormal way.
If there is an object in the camera connected to the system,
connect the camera to the video input port to check the
video and check if there is any issue with the existing cameras
connected to the system.
68
Reference
Symptom
Checkpoint and resolution
If there is an issue with the camera connected to the system,
connect a different camera to the video input port to check
whether the existing camera connected to the system has an
issue.
Check whether the video cable connecting the device and the
camera is damaged.
There is noise in the video.
Check whether there is a cable with high voltage near the video
cable. It can cause noise in the video or cause deterioration in
the video quality.
Check whether the video cable connected between the device
and the camera is the cable for correct usage.
If the power cable is used for the usage of video cable, it can
cause noises in the video.
Check whether the sensor type set in the sensor setting menu is
the same as that of the sensor.
The sensor connected to the
device is not working.
From the schedule management item of the recording setting
menu, check whether the recording using the sensor is set up.
Check whether the sensor is correctly connected to the ALARMIN port.
Check whether the PTZ camera is correctly set up from the
camera setting menu.
6
Check whether the power cord of the PTZ camera connected to
the system is correctly connected.
Reference
PTZ camera connected to
the device is not working.
Check whether the signal cord connected to the PTZ camera
connected to the system is correctly connected.
Check the channel the PTZ camera connected to the system
controls.
Check the user type. General user cannot use the PTZ function.
Reference
Symptom
69
Checkpoint and resolution
When the E-mail transmission fails without SMTP server setting.
I cannot receive the E-mail
sent from the device.
•
Check whether the network is set up correctly.
•
Check whether the E-mail address is entered correctly.
•
Check the spam mail setting for the entered E-mail address.
(If the spam mail is set, some mails may automatically be
deleted or classified into spam mail box etc.)
•
Some SMTP mail server providers does not support sent
email from the commercial SMTP server. In this case, use a
public SMTP server.
When the E-mail transmission fails even with the SMTP server
setting.
•
If you see a message saying “Please check the SMTP
information or internet cable”.
--
•
I cannot see the video screen
connected with i-Phone.
•
Check the SMTP server address.
--
Check the SMTP port number.
--
Check the network setting.
If the E-mail cannot be received without any error message.
--
Check the E-mail address of the recipient.
--
Check the spam mail setting for the entered E-mail
address.
Check if wireless internet is available.
--
If receive sensitivity is low, it can be disconnected or you
cannot see the video.
6
Reference
70
Reference
6-2. Recommended device to use
List of recommended USB memory
6
Classification
Manufacturer
Model name
Capacity
1
ELECOM
MF-BU201GWH
2
BUFFALO
RUF2-E1GL-BL
3
Scandisk
4
SONY
5
PRINCETON
PFU-STS1G
6
DATA
TB-ST1GB I-O
7
FM Semiconductor
MLC gold
8
SAMSUNG
9
Transcend
JetFlash V10
10
IMATION
Atom USB Drive MLC
11
Sky Digital
SKY-DRVx2
32G
12
LG
XTICK
8GB
1GB
Cruzer Micro
Cruzer Micro U3
8/16GB
USM1GJX
1GB
USM8GH
8GB
SUM-M4GPV
1GB
4GB
SUM-LWW
8GB
Reference:
Reference
Even when the USB memory listed in the above list is recognized in this device, it may not
operate normally.
NOTE
•
For some monitor TCs, the screen output size may not fit.
•
For monitors that do not support resolution of 1280 x 1024, the output may not be
normal.
Reference
71
Recommended list of CD/DVD media
Manufacturer
CD-R
CD-RW
DVD+R
DVD-R
DVD+RW
DVD-RW
LG
O
O
-
O
-
-
Samsung
Pleomax
O
O
O
O
O
-
Melody
O
O
O
O
O
-
Sony
O
-
O
O
-
-
MITSUBISHI
O
O
O
O
-
O
Verbatim
O
O
O
O
O
-
Memorex
-
O
O
O
O
O
NOTE
Dual layer and mini CD/DVD is not supported in the recommended list of CD/DVD media.
6
Reference
72
Reference
List of supported PTZ camera
Protocol
6
Reference
Manufacturer
Pan/Tilt
Zoom
Focus
Iris
Preset
Tour
LG Multix_E
LG
X
O
O
O
X
X
LG Multix
LG
O
O
O
O
O
O
LPT-A100L
LG
O
X
X
X
X
X
LVC-C100/200HM/LG
Electric Inc
LG
X
O
O
O
X
X
HSDN251 / Honeywell
Co., Ltd
Honeywell
O
O
O
O
O
O
MD200/2000/1200/800/
Sony Co., Ltd
Sony
O
O
O
X
X
X
New Born / NEW BORN
HIGHTECH
New Born
O
O
O
O
O
O
WVCS850 / Panasonic
Dongyang
O
O
O
O
O
O
PLECO -D / PELCO Co.,Ltd
PELCO
O
O
O
O
O
O
PLECO -P / PELCO Co.,Ltd
PELCO
O
O
O
O
O
O
SAMSUNG_E / SAMSUNG
Co.,Ltd
SAMSUNG
O
O
O
O
O
O
SPD - 2300/3000/3300/
SAMSUNG Co.,Ltd
SAMSUNG
O
O
O
O
O
O
SUNGJIN
O
O
O
X
X
X
DYNACOLOR
O
O
O
O
O
O
VICON
O
O
O
X
X
X
SUNGJIN / SUNGJIN
Co.,Ltd
TPD7720 / DYNACOLOR,
INC
V1305R-DC / V1311RB/
CRX-1013 / VICON
NOTE
LE6016N/LE6016D is not compatible with KVM because of exclusive use of mouse.
Reference
73
6-3. Initial setting list for factory default
1 Step
2 Step
SYSTEM
OVERVIEW
3 Step
4 Step
INPUT
Default
REMOTE ID
00~99
00
DE-INTERLACE
ON / OFF
ON
AUTO-SWITCHING
1~30 Sec
10 Sec
SPOTDIVISION
1 / 4 / 16
1
SPOT-OUT
AUTO/1~16
1
BUTTON BUZZER
ON/OFF
ON
LANGUAGE
ENGLISH
OVERWRITE
ON / OFF
ON
USE DATA RETAIN
ON/OFF
ON
RETAIN DAY
1 ~ 60 Days
30 Days
DATE
-
TIME
-
LOCALE
-
DATE/TIME
6
OFF
Reference
NTP SERVER
OFF
Time.nuri.net
Time.kriss.re.kr
ntp.tmc.edu
ntp2.ja.net
ntp.cmr.gov
ntp.shim.org
stdtime.gov.hk
time.service.uit.no
pool.ntp.org
74
Reference
SELECTION
PASSWORD
INITIALIZE
CONTROLLER
6
CAMERA
Reference
CHANNEL
admin/user1/user2/
user3
admin
OLD
-
NEW
-
CONFIRM
-
CAMERA SET
1~16
1~16
SETUP
O/X
X
SEARCH /
BACKUP
O/X
O
PTZ
O/X
O
AUTO LOGOUT
Off, 5 Min to 60 Min
Off
FACTORY
ON/OFF
OFF
LOG
ON/OFF
OFF
SETTING
ON/OFF
OFF
HDD
ON/OFF
OFF
USE
ON/OFF
OFF
DEVICE ID
1~16
1
BAUD RATE
1200~115200
9600
CAMERA
1~16
1
CHANNEL NAME
CH 01
CAMERA1
AUDIO 1~4
CAMERA1~16
NOT USED
NOT USED
Reference
RECORDING
SCHEDULE
CAMERA
1~16
1
RESOLUTION
CIF/
HALF D1/
D1
CIF
FRAME
1~30
30
EVENT FRAME
OFF / 1 / 5 / 7.5 / 10 /
15 / 30
30
QUALITY
VERY LOW
LOW
NORMAL
HIGH
VERY HIGH
NORMAL
CAMERA
1~16
1
C/H/E/N
C
CAMERA
1~16
1
BRIGHTNESS
0~100
50
CONTRAST
0~100
50
SATURATION
0~100
50
HUE
0~100
50
75
COPY
HOLIDAY
COLOR
6
Reference
76
Reference
CAMERA
1~16
1
DEVICE NAME
LG-Multix_E
LG-Multix
LPT-A100L
LVC-C100
HSDN251
MD200
New Born
WVCS850
PELCO-D
PELCO-P
SAMSUNG_E
SPD-2300
SUNGJIN
TPD7720
V1305R-DC
OFF
OFF
PTZ
DEVICE ID
EVENT
6
Reference
SENSOR
0
BAUD RATE
1200~115200
9600
TOURING
INTERVAL
5 Sec
10 Sec
20 Sec
30 Sec
1 Min
3 Min
5 Min
1Min
SENSOR
1~8
1
TYPE
N.O/N.C
N.O
CHANNEL
1~16/OFF
1
ALARM
1~4/OFF
OFF
ALERT
ON/OFF
OFF
SPOT-OUT
ON/OFF
OFF
DURATION
1~10 Sec./OFF
10 Sec.
Reference
CHANNEL
1~16
MOTION ZONE
MOTION
VIDEO LOSS
1
SELECT ALL
SENSITIVITY
1 ~ 10
5
ALARM
1~4/OFF
OFF
ALERT
ON/OFF
OFF
SPOT-OUT
ON/OFF
OFF
DURATION
1~10 Sec./OFF
10 Sec.
CHANNEL
1~16
1
ALARM
1~4/OFF
OFF
ALERT
ON/OFF
OFF
DURATION
1~10 Sec./OFF
10 Sec.
MODE
ON/OFF
OFF
SMPT SERVER
-
PORT
25
ACCOUNT
-
PASSWORD
-
SENDER
-
RECEIVER
-
6
E-MAIL TEST
-
Reference
E-MAIL
77
78
Reference
NETWORK
DHCP IP
STATIC IP
PPPoE
CONFIG
TCP / IP
IP ADDRESS
-
SUBNET MASK
-
GATEWAY
-
DNS
-
MAC ADDRESS
STATUS
PPPoE
DISCONNECT
USER
PASSWORD
Reference
DDNS
CMS
-
WEB
80
PLAYBACK
9091
LIVE
9092
CAMERA
1~16
FRAME
OFF / 1 / 5 /
7.5
QUALITY
VERY LOW
LOW
NORMAL
HIGH
VERY HIGH
NORMAL
MODE
ON/OFF
OFF
STREAMING
6
DHCP IP
SERVER
www.lgddns.com
PORT
9002
DOMAIN
-
INTERVAL
1~60 Min
5 Min
MODE
ON/OFF
OFF
IP ADDRESS
-
PORT
0
Reference
EVENT FILTER
INFO
INFORMATION
SYSTEM START
ON/OFF
OFF
SHUTDOWN
ON/OFF
OFF
SETTING CHANGE
ON/OFF
OFF
LOGIN/
LOGOUT
ON/OFF
OFF
SENSOR
DETECTION
ON/OFF
OFF
MOTION
DETECTION
ON/OFF
OFF
VIDEO LOSS
ON/OFF
OFF
ALARM OUTPUT
ON/OFF
OFF
MODEL
-
IP ADDRESS
-
MAC ADDRESS
-
F/W VERSION
-
OS VERSION
-
VIDEO TYPE
-
79
INTERNAL HDD
EXTERNAL HDD
-
F / W UPDATE
FILE
NOT EXISTED
IMPORT
SET UPDATE
EXPORT
REFRESH
DESABLE/ENABLE
DESABLE
-
6
Reference
SYSTEM LOG
80
Reference
6-4. Product specification
MODEL
LE6016N
OPERATING SYSTEM
Embedded Linux
COMPRESSION
H.264 Hardware Codec
MULTIPLEX FUNCTION
Live, Record, Backup and Network at the same time
RECORDING RESOLUTION
D1, Half D1, CIF
RECORDING SPEED
480 fps (NTSC), 400 fps (PAL) at CIF Resolution
VIDEO INPUT
16 BNC Composite
VIDEO OUTPUT
2 BNC Composite (Main, Spot-out), 1 VGA (15PIN DSUB)
AUDIO INPUT/OUTPUT
4 line/ 1 line
SENSOR INPUT / ALARM OUTPUT
8 line (NC/NO selectable)/ 4 line(NC/NO selectable)
Display Mode
BACKUP MEDIA
STORAGE MEDIA
1/4/9/13/16 and Auto sequential
USB storage, Network and
external ODD
USB storage, Network and
internal ODD
2 SATA HDD
1 SATA HDD
RECORDING MODE
Continuous, alarm, motion, and instant panic
OPERATION CONTROL
Front Key, Mouse and Remote controller
COMMUNICATION PORT
RS-485
NETWORK
LAN (Ethernet RJ-45, 10/100/1000 base), DDNS, TCP-IP
SIZE(WxDxH)
430 mm x 330 mm x 57 mm
WEIGHT (without HDD)
2.65 kg
POWER
6
Reference
POWER CONSUMPTION
ø
LE6016D
3.45 kg
DC 12 V Adapter (60W)
20 W
17 W
OPERATING TEMPERATURE
0 °C to 40 °C
OPERATING HUMIDITY
10 % RH to 80 % RH
The detail and specification of this product can partially change for quality
improvement.
Download PDF