LG | LDV-S802 | LG LDV-S802 Owner’s Manual

LDV-S802_ENG_MFL-28
DIGITAL VIDEO
RECORDER
OWNER’S MANUAL
MODEL: LDV-S802
Before connecting, operating or adjusting this product,
please read this owner’s manual carefully and completely.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE.
WARNING :
This is a class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
CAUTION:
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product
and to protect it from over heating.
The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation
is provided or the manufacturer's instruction have been adhered to.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this product does cause harmful interference to radio or television reception,
which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the product and receiver.
•
Connect the product into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This product is manufactured to comply with the EEC DIRECTIVE 89/336/EEC, 93/68/EEC and
73/23/EEC.
2
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S
MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1.
Read these instructions. - All these safety and operating instructions should be read before the product is
operated.
2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.
3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use instructions should be followed.
5. Do not use this apparatus near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry
tub, in a wet basement; or near a swimming pool; and other areas located near water.
6. Clean only with dry cloth. - Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product
and to protect it from over-heating. The openings should never be blocked by placing the product on a bed,
sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
3
Safety and Notice
It is strongly recommended that you read this manual and use it in a proper way.
The followings might cause a fire
•
Avoid placing the unit near direct sunlight, heat source such as a heater, etc.
•
Do not share the outlet with the other appliances. It might cause an abnormal heating and a fire.
•
When smoke goes up or when you smell a strange smell, stop using the unit. In this case, turn the unit off,
unplug it, and contact the after-sales service center. If you continue using the product, it can cause a fire or
an electric shock.
•
Place the unit at a distance from a heat source. It is in danger of a fire.
•
Don’t put burning material such as a flammable spray, etc. It can cause a fire.
•
Don’t install the unit at a dusty place. It can cause a fire.
•
Plug the unit firmly not to be shaky. If the plug is not safely inserted into the outlet, it can cause a fire.
•
When the multi-outlet is used, don’t use several appliances at the same time. The abnormal heating of the
outlet can cause a fire.
•
Don’t damage, modify, bend, twist, pull, stick, or heat the power code and the plug.
•
If the plug is loose in the outlet, don’t use it. It can cause a fire or an electric shock.
•
Don’t insert the metals such as a coin, a hair pin, a piece of iron, etc. or flammable material such as a
paper, a matchstick, etc. in the product. It can cause a fire or an electric shock.
The following might cause an electric shock
•
Don’t put a vase, a cup, cosmetics, a medicine, a container having water on the product.
•
Don’t insert or drop the metals (a coin, a hair pin, an iron piece, etc.) or flammable material (a paper, a
matchstick, etc.) into the ventilating opening.
•
Don’t put a heavy object on the product. It can cause an electric shock.
•
Don’t plug or unplug with a wet hand. It can cause an electric shock.
•
Don’t unplug the unit by pulling the power cord. If the cord is damaged, it can cause an electric shock.
•
Avoid twisting the power cord. It can cause an electric shock.
•
Don’t install the unit at the place exposed to rain and wind or splashing water.
•
Don’t disassemble or modify the product at your discretion. (It can cause a problem and an electric shock.
•
Don’t put a heavy object on the power cord nor keep it pressed down by the product.
•
Don’t insert the metals such as a coin, a hair pin, a piece of iron, etc. or burning material such as a paper,
a matchstick, etc. in the product. It can cause a fire or an electric shock.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste
stream via designated collection facilities appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for
the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office,
waste disposal service or the shop where you purchased the product.
4
INTRODUCTION
LDV-S802, High-tech 4ch standalone Digital Video Recorder introduced by LG with the leading video recording technologies with many years experience and know-how, can record high quality data of the maximum of
120fps and allows the user to monitor and control local DVRs in a remote site via LAN connection.
User friendly designed LDV-S802 provides the most convenient system use. Software motion detection on
separate assignment of motion area enables the system to start recording only when the motion is detected.
Max. 2 internal HDDs could be installed in the system.
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Real time live images display at the highest resolution
Easy to install and convenient to use
Motion triggered recording function
Sensor input and output relay function
Reserved recording function - by Motion, Sensor or Time setting
Remote network control on dynamic IP network environment
NTSC / PAL Autoselectable
The highest rate data compression by MPEG-4 technology
Convenient Data backup on USB memory stick
Various search function (Date/Time Search,Event Search,Go to First, Go to Last)
Multi-site Web viewer
Triplex ( Live display, Recording, Network)
RTOS Operating System
Small file sizes by MPEG-4 compression
Various recording resolutions
- NTSC : 720X480, 720x240, 360x240.
- PAL : 720X576, 720x288, 360x288.
Up to 120FPS@360 X 240 (NTSC) / 100FPS@360 X 288 (PAL) recording
Up to 500GB internal storage (Expandable if new high capacity HDD is launched)
Various monitor output (Video out, Loop, VGA, S-VHS, Spot)
4 Audio input channels
Daylight saving mode
Support PS2 mouse, IR Remote Controller
Multi-Languages selectable
Alarm notification by e-mail
Multi-site PC client software
Pre-alarm recording
Easy system S/W update with USB Memory Stick
•
Image Rate & Quality adjustment per individual camera
APPLICABLE INSTALLATION
•
•
•
•
Bank, ATM machine, Mart, Convenient store and other public areas.
Private home, Apartment, Jewelry shop and commercial compound which requires unmanned surveillance
or anti-theft.
Warehouse, stock area and workplace where to prevent accidents or its clarification.
Places to be monitored from remote site.
Note
LDV-S802 doesn’t support CD±RW media for data backup or playback.
5
Contents
PACKAGE COMPOSITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Product composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PRODUCT COMPOSITION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DVR system composition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Basic composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
External Device Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
BUTTONS AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Rear side view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
HDD INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-16
Note for adding HDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
HDD installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-16
HOW TO USE REMOTE CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18
Remote controller ID setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
HOW TO USE DIRECTION KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
HOW TO USE PC MOUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
OSD DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
Explanation for the Booting Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
System power ON indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Screen OSD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
How to open the setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
System setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-31
System information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Time / Date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Password setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Hard disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Default setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-30
> BACKUP MARK IN-OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Button Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-38
OSD (On Screen Display) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-33
Split mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-36
Auto Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SPOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
NETWORK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-44
Network installation and diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
NETWORK configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
> DHCP function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
> IP INFORMATION SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
> PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
> NETWORK PASSWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
> NOTIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-43
> MAC ADDR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
> SERVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
6
CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-51
RECORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
RECORD SCHEDULE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CAMERA TITLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
VIDEO ADJUST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
PTZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
> PAN/TILT camera connection diagram. . . . . . . . . . . . . . . . . . . . . . 49
> PTZ camera connection and settings. . . . . . . . . . . . . . . . . . . . 50-51
EVENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-55
ALARM / SENSOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
ALARM / SENSOR SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
> ALARM MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
> ALARM DWELLTIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
> EVENT DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
> EVENT RECORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
> EVENT BUZZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
> VIDEO LOSS BUZZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
> SENSOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
> CH (Channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
> Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
> SENS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
How to search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-58
Using the SEARCH button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
DATE & TIME Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
How to control the search speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
EVENT Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Search for the first record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Search for the last record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
How to use the audio buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
How to listen to the audio channel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
EMERGENCY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
REMOTE SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-76
Remote software installation and PC requirement . . . . . . . . . . . . . . . . . . . 62
How to use remote software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
> Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
> Screen and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-65
> Setting the remote system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-71
> How to remotely search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72-73
> Remote backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
> Backup data search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75-76
Web monitoring login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77-84
Default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77-78
The table of menu setup applying time . . . . . . . . . . . . . . . . . . . . . . . . . 79-80
Models compatible with the USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
HDD storage capacity table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82-83
The estimation of backup speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
7
PACKAGE COMPOSITION
Product composition
The parts supplied with the product can be different depending on the model.
LDV-S802 (DVR unit)
Remote controller
S/W and manual
8
Adaptor
External signal connector
(Fixed at rear of DVR)
Power cord
AAA Type
Battery
Manual
HDD fixing screws
(12pcs)
PRODUCT COMPOSITION
DVR system composition
The system can record max. 4ch incoming asynchronous video data and allow various screen display of
recorded data through AV and VGA monitor outputs. Using Internet line, user can access remotely located system, and monitor sites, control functions and search recorded data.
Basic composition
Audio
input
Mouse
Spot out
Audio
output
Camera inputs
Sensor 1-4
Internet
CCTV
monitor
Alarm
PTZ
Camera
Loop out
Power
(Adaptor DC 12V, 5A)
VGA output
Video input signals use identical type (NTSC/PAL) of 1.0Vp-p, 75 ohm.
External Device Connection
•
•
•
•
•
•
•
•
•
•
Max. 4 asynchronous video signal inputs.
System provides Monitor output x 1, Spot out x 1, VGA out x 1, S-Video out x 1.
Audio: Recordable Max. 4channels of audio signals (Lines).
RS-485: Camera control (Pan, Tilt, Zoom, Focus).
LAN: This is to review and control remote site DVR units via Internet connection. By simple network setup
of DVR, the user can control local DVR in an easy way.
SENSOR IN: By connecting sensor input, various events can be controlled by the system.
ALARM OUT: To transmit alarm out signals.
Using memory storage, user can backup the data.
It performs system upgrade via USB memory storage.
For users accustomed to the PC, system provides PC mouse to connect the system.
9
BUTTONS AND FUNCTIONS
Front View
a
j
k
b
c
l
a OVERWRITE
This indicates that the OVERWRITE function is
enabled.
Note
OVERWRITE indicator On/Off doesn’t mean HDD
is actually overwriting, but it means OVERWRITE
function is enabled. Actual overwriting will be in
effect when the HDD is full.
b HDD FULL
This indicates that the HDD is full or being overwritten.
c NETWORK
This indicates that the system is being accessed
by remote user via Internet or LAN.
mn o
i
pqr
j SPLIT (Split mode screen display)
The button is used to display different types of
split display mode. Press the button and hold
for about 1 sec to select one of various display
options (See page 34).
k CHANNEL buttons
The button is used to select monitor screen or to
input password.
l SEQ button
The button is to display sequence screen (See
page 37).
m AUDIO button
To select channel audio sound on Playback or
Live mode (See page 59).
d SET UP button
To call setup menu (See page 23).
n N (Play) button
It is for playback and pause from search menu
and it uses for the menu selection too.
e m (REW) button
To see reverse playback or move menu selection
to the left [←].
o x (STOP) button
To stop data search or move menu selection to
down[↓].
f SEARCH button
To playback data or to move selection up [↑] on
the menu.
p BACKUP button
To use USB backup (See pages 28-30).
g M (FF) button
To playback fast forward or to move menu selection to right [→] STOP Button.
h PTZ button
To control PTZ camera (See page 49).
i EMERGENCY button
In emergency situation, user can manually start
recording all channels by selecting the button
and this emergency recording will be activated
regardless of previously configured schedule
setup. (See page 60).
10
de f g h
q SCHEDULE button
To record under previously arranged recording
schedule setup (See page 46).
r USB interface
To backup data or upgrade system firmware.
Note
Only USB memory stick can be connected to
USB port. The connections of other USB interface device may cause system malfunction. (See
page 81).
Rear side view
a
f
b
g
c
h
d
e
i j
k
l
m
a MOUSE
PC mouse connection port.
b AUDIO Input jacks (CH1~CH4)
Input for each channel audio.
c AUDIO OUT
Output for audio stream.
d SPOT OUT
Video output connector for another monitor display of selected channel (See page 38).
e VIDEO IN
BNC Video input for each camera channel.
f LAN port
LAN port for network connection.
g RS-485, ALARM OUT/IN terminals
PTZ camera (RS-485), Sensors and alarm connection (See page 49 and page 52).
h VGA output
Video output connector for PC monitor (LCD/CRT) use.
i S-VHS (S-Video connector)
Video output connector for monitor which has S-Video type connection.
j VIDEO OUT (Composite)
BNC Video output for main monitor display.
k LOOP OUT
Video output for each camera channel display without any image processing or disturbance.
l POWER input terminal (DC 12V)
DC adapter power input.
Note
Electrically matched adaptor must be used. Unqualified adaptor use may cause problems such as intermittent system rebooting, power off and etc. Warranty service will not cover system damaged by improper
adopter use.
m Power switch (ON/OFF)
System ON/OFF.
11
HDD INSTALLATION
The user can install the HDD on the product. But, since there are many parts and elements inside the product
that can cause electric shock, troubles, faults on the product and etc. Further inappropriate HDD installation
may generate HDD detection problem or not operate properly, Therefore it is advised to have the initial HDD or
additional HDD installation work done by a well experienced engineer from the agent where the product was
purchased.
Note for adding HDD
•
Pay special attention to avoid incorrect cable connection or scratches on the cable.
(It may cause product failure or fire)
•
Be careful not to get injured by the sharp edge of the internal side of the product.
•
Be careful not to lose any of unscrewed pieces or parts. Incomplete fixing and assembling may cause operational failure or malfunction.
HDD installation procedure
1. Remove the cover by unscrewing 2 screws on the right side panel, 2 screws on the left side panel, and 5
screws on the rear panel.
12
2. Connect the data bus cable to the board making the red part of the cable contact the groove on the
connector.
3. Separate the screw from the HDD guide to install the HDD. If the system is hipping without HDD, refer to
the “One HDD installation” (In case of adding the HDD, refer to the “Two-HDDs installation”).
One HDD installation
For initial HDD installation, place HDD on A position and
connect the HDD cable as shown left.
A
B
A
Two-HDDs installation
Place existing HDD on A (Master setting) position, and
place second HDD on B (Slave setting) position.
Use middle connector of HDD cable to second HDD as
shown left.
•
Power cable connection : Use available cable nearest
from the HDD.
13
4. Remove the HDD rack and mount the HDD on rack. The power source and cable connection should face
the rear side.
The power and cable connection ports must face the rear side.
5. Fixate the HDD by using two screws on the left and 4 screws at the bottom of the rack.
14
6. Remove the HDD rack from the DVR and mount the HDD on the rack. The power and data cable
connection ports should face the rear side.
7. Connect HDD cable and power cable.
Data Bus cable
Power cable
15
8. When mounting 2 HDDs, connect the cables to the left and right sides as shown below.
9. After mounting the HDD, screw fix the cover.
(4 points on the left side and 5 points at the rear side)
Notes
• When adding a HDD, it is recommended to use the same brand HDD as the one being used.
• When mounting 2 HDDs, Master and Slave must be set correctly.
(Refer to the instruction manual provided by HDD manufacturer for Master/Slave jumper setting)
• Set as Master when one HDD is installed.
The HDD should be formatted after installation
When installing or adding the HDD, it should be formatted before use.
The HDD which has been used in another device should be formatted to make sure normal storage.
[Setting] Menu → System → Hard disk
16
HOW TO USE REMOTE CONTROLLER
By using this easy to carry remote controller, user can use all the functions of LDV-S802 and can separately
control multiple numbers of DVRs installed in the same place.
a
g
h
b
i
j
c
d
e
k
f
a ID button
By assigning DVR ID, it allows the user to control multiple DVRs with one remote controller.
b Split screen switch (Including PIP)
This is used to convert to PIP mode. Internal image position will change whenever the button is pressed.
c BACKUP button
This is used to backup recorded data into USB memory stick.
d AUDIO button
This is used to select audio listening mode per each channel.
e SEQ button (Sequence screen display button)
This is the automatic sequencing function button. It repeatedly switch screen display as initially set.
f PTZ camera button
Used when it control PTZ camera.
g SEARCH button
To search recorded data from the HDD.
h Channel selection button and password input
To select video channel or to enter system password.
i SET UP button
This is used to setup the system menu.
j Direction and playback speed control button
This is used as direction keys, configuration buttons and playback speed control buttons.
k Record button (Emergency / Schedule)
This is used to schedule and execute emergency recording.
17
Remote controller ID setup
1. Confirm system ID (Default set as “01”).
How to confirm system ID:
Press SET UP button → [SYSTEM] → [INFORMATION] → [REMORE ID]
2. Assign separate ID in order to control multiple systems (Max. 99).
3. Select “ID” button and press number (ID no.) The number must identical to the ID to call.
Caution
•
•
18
Remote controller works only when the ID of the system and controller are same. The ID should be confirmed when remote controller doesn’t call DVR.
When system ID has changed, the user will not be able to use the buttons on the remote controller, but
only the ID button will work. (After matching controller ID to system ID, you may use all buttons on remote
controller.)
HOW TO USE DIRECTION KEYS
To optimize the number of buttons and to maximize stylish design, the development was focused on
multi functional button use. Therefore most of buttons have more than one functionbut it is still very simple to
use.
a
b
c
e
f
d
a SET UP button
• Open menu.
• Close menu when opened.
b LEFT (m) button
• Menu move left.
• Key move left on screen keyboard.
• PTZ moves left.
c UP (SEARCH) button
• Menu move up.
• Selected menu change.
• PTZ move up.
d RIGHT (M) button
• Menu move right.
• Key move right on screen keyboard.
• PTZ move right.
e SELECT (B[[) button
• Menu selection.
f DOWN (x) button
• Menu move down.
• Key move down on screen keyboard.
• PTZ move down.
19
HOW TO USE PC MOUSE
For those users who are accustomed to the PC mouse more than buttons, the system provides PC mouse
connection port to control the system.
Caution
Connect mouse before the system power is turned on
or reboot the system after connecting the mouse to the
system.
Select
Menu call or
cancel
Click right side button on mouse to call menu
on screen and change setup figures by using
Up/Down icons.
Notes
•
•
•
20
Menu call → Click right mouse button.
Menu selection → Click left mouse button.
Cancel while menu window is displayed → Click right mouse button.
OSD DISPLAY
Explanation for the Booting Display
When the system is turned on, it will show LDV-S802 booting screen together with relevant information.
System information and HDD information will be displayed followed by network information on the screen.
a
b
a Screen displays Model, Version and Video mode information.
• Model: Model name.
• H/W VER: Current system hardware version.
• S/W VER: Current system software version.
• VIDEO MODE: Current video mode (System will automatically detect NTSC or PAL mode by evaluating
connected video signals. When there is no incoming video signal, previous setting will remain).
Note
Don’t connect both NTSC and PAL type cameras to the system.
System doesn’t support two different types simultaneously.
b It displays storage device information (“+” indicates storage being recorded).
c
c It displays network information connected to the system.
21
System power ON indicator
The display lamp does not blink as soon as the power is turned on.
Circle power indicator.
Screen OSD
On screen icons include Recording status, Time, Camera name and etc.
a
c
b
a
d
e
a Indicate camera name.
b Turns red when the channel is being recorded (No icon will be displayed when the channel is not being
recorded).
c Displays Year and Date.
d Displays Current Time.
e Indicates total HDD utilization factor.
22
How to open the setup menu
The menu can be configured by using the front button or the mouse. Because it sets up the overall setting of
the system, you should be familiar with it.
Notes
•
•
•
How to open the menu with the front button.
There is the “SET UP” button on the upper right side of the front panel. The menu pops up when you press
it once.
How to open the menu by using the remote controller.
Press the SET UP button from the remote controller.
How to display the menu with the mouse.
The pop-up menu is displayed by clicking the right button of the mouse.
System setup
The system setup shows the system status and setup protection for management such time, date, password
etc.,
Note
There are two different types of menus. One is the menu that is immediately applied menu by selection and the
other is menu which is applied after closing from the menu. (Refer to the Appendix)
23
System information
a
c
d
f
b
e
g
a REMOTE ID
LDV-S802 supports the ID remote controller. One remote controller can control multi DVR system (Max 99).
b MOUSE RESOLUTION
It displays the sensitivity of mouse movement. It can be adjusted to the user conveniences (default: 1).
(Motion speed is slow) 1 < 2 < 3 (Motion speed is fast)
c LANGUAGE
The language being used on the system can be changed. It supports 4 different languages.
The relevant language will be selected before shipping.
d MODEL
It shows up the model name.
e H/W VER
It shows up the current H/W version.
f S/W VER
It shows up the current S/W version.
g WEBCODE
It shows the serial number of the product, which will be used for registering in the web.
(http://www.lg-security-s800.com)
24
Time / Date
a
b
c
d
e
a Time
It sets up the time and displays it from the front in the format of, hour: minute: second.
b Date
It sets the date and displays it from the front in the format of, year : month: day.
c Date format
Since the time display could be different by each country, select the format you want.
- ASIA: YY/MM/DD → 2006/05/31
- US : MM/DD/YY → 05/31/2006
- EURO: DD/MM/YY → 31/05/2006
d Time correction
This is for reducing the time difference as much as possible by automatically adjusting the time discrepancy
daily or, monthly.
e Daylight saving
It is so called “SUMMER TIME”. It is adjustable to be faster or slower from the standard time.
Caution
If you change the time setup, “HDD data can be erased” message will show up.
For example, if you delay the time by 10 minutes, the overlapped 10minutes data can be deleted.
25
Password setup
This is used to important system changes such as HDD format or lock.
How to change the password
•
System Password
Factory default(1111) or user password.
•
New password
Input the new password using the numeric key 1-4.
(System password can be entered by combining 1-4 only)
•
Confirm password
Input the new password again for the confirmation.
•
Password changed
It means the password is successfully changed.
Note
There are two different passwords. The one is the system password and the other is the network password.
The function of each is slightly different.
26
•
System password
The password can be composed of numbers from 1-4 and is used for the important system changes such
as the HDD format and system lock etc.,
•
Network password
There is the ADMIN password and the USER password. It is used to search, setup and control through the
network. The system has the separate password since the HDD format etc., can not be changed through
the network.
Hard disk
a
c
e
b
d
f
a If you select 1, 2 HDD information display mode, it shows the model name, size and used space of HDD.
•
•
•
•
NO : HDD1, HDD2
FORMAT : LDV-S802
SIZE : 152GB
USED : 37%
b “+” mark
It shows the Record setup HDD.
c HARD DISK FORMAT
You can format the newly installed HDD or the existing HDD currently in use.
Sequence: HDD format → Password input → HDD selection → O.K
d OVERWRITE
If the HDD is full, it saves data by overwriting it. If this function is selected, OVERWRITE light will blink on
the front panel (The menu setup is not available when recording).
e RECORD HDD
Up to 2 HDDs can be installed inside the LDV-S802 and the sequence of storage can be selected by the
user.
Note for the HDD recording sequence
• HDD1: HDD1 recording. (It records only on HDD1 although the HDD2 is installed.)
• HDD 2: HDD2 recording. (It records only on HDD2 although the HDD1 is installed.)
• HDD1-2: Recording for HDD1, HDD2.
f AUTO DELETE
It deletes the HDD video data if the selected duration time for saving elapses.
(scope: off, 10days, 20days, 30days, 40days, 50days, 60days → the image data before the selected
duration will be automatically deleted.)
27
Default setup
This is used when the user wants to reset the unit to the factory default.
(Refer to the appendix for the factory default)
[Change sequence]
DEFAULT SETUP → PASSWORD INPUT → O.K
Upgrade
LDV-S802 is designed to upgrade the firmware in case of function change or addition of new function.
[Change sequence]
1. Save the firmware file(LDV_S802.BIN) in the memory stick.
2. Plug the memory stick to the USB port on front panel then, click the SETUP button.
3. Select the “6.UPGRADE” from the SYSTEM menu.
Note during upgrade
• Do not remove the memory stick while upgrading.
• Do not turn off the power while upgrading.
• It reboots itself after 3 seconds when the upgrad is completed.
• If there is any problem, please contact your local dealer.
Backup
The video file can be backed by the memory stick very easily. The USB memory stick is the only possible
backup device. Insert the USB memory stick into the USB port and select the BACKUP.
a
b
c
d
e
a BACKUP
If the system recognizes the USB memory stick, it shows the total space.
b Select the Channel to back up. The above example displays the CH1 selection.
c Select the start time for backup.
d Select the end time for backup.
e If the setup is completed, click “NEXT".
Caution
This unit supports only FAT16 or FAT32 format for USB Memory Stick. Before using the USB Memory Stick,
you must format the USB Memory Stick on a PC with FAT16 or FAT32 format.
28
f
g
f It shows the back up size of the set time.
Note
Check the backup size and the memory space.
If the backup size is larger than available memory space, you have to use the bigger memory stick or
reduce the backup image size to fit the memory stick.
- Refer to the appendix for “Recording time table”
- The backup size is displayed from KB to MB.
g Now, you can copy the files to the memory stick. Click the “COPY TO USB” and remove the memory stick
when it is completed.
Note
To see the backup video data.
The backup video data can not be displayed on DVR but, it is possible through the client software (See
page 74).
29
> BACKUP MARK IN-OUT
To make the back up easy, the user can select the backup area seeing the playback picture.
1. Insert the memory stick to the USB port of the unit.
2. Search the image referred by BACKUP (See page 28).
3. If the user find the image want, press the BACKUP button then, BACKUP MARK-IN message shows
and save the backup start time. If press again, “BACKUP MARK-OUT” message shows and save the
backup end time. After that, it moves to the BACKUP screen automatically.
4. The backup time is already set on as above. According to the BACKUP, backup the image to the
memory stick (See page 28).
30
Button Lock
The button lock asks the password every time when you control or, modify the system.
•
•
Select ON: Enable button lock.
Select OFF: Disable button lock.
31
Display
The display menu can control the display related items such as displaying OSD, picture split etc. Set it up
properly according to the needs of the user.
OSD (On Screen Display)
a
c
e
g
a DISPLAY
Setup whether to display the OSD.
b TIME
Setup whether to display the time.
c DATE
Setup whether to display the date.
d TITLE
Setup whether to display the title.
e TRANSPARENCY
Setup the transparent OSD.
f BORDER COLOR
The color of screen-split border line (White, Black).
g DISPLAY POSITION
OSD display format (select one from A,B,C or D).
32
b
d
f
OSD A TYPE
OSD B TYPE
OSD C TYPE
OSD D TYPE
33
Split mode
The factory default of channel split is quad. If you press the SPLIT button, the picture shows up as a quad but,
it can be changed to the other asymmetric split. If the user needs careful monitoring, this can be used effectively.
Note
If you press and hold the SPLIT button, it changes to the split mode. It can be selected through the main menu
but also by, simply pressing the SPLIT button.
There are seven different split modes. Select the desired one to use.
34
QUAD-1
QUAD-2
QUAD-3
3WAY-1
35
3WAY-2
3WAY-3
2WAY-1
36
Auto Sequence
a
c
b
d
Auto sequencing is the sequential screen display for the effective monitoring. Press the SEQ button to use.
a AUTO LOSS SKIP
It is to set up to skip the channel when there is the no camera input.
b SEQUENCE MODE
It is to set up whether to show the channel as a sequence mode.
- FULL: It shows the full screen sequentially.
- PIP: It shows the PIP image sequentially.
c PIP SEQUENCE
In case of No. 2, if the setup is FULL, it will show each channel in full sequencing but, if it is setup as PIP,
another small image channel will be shown on the full screen channel. You can set which of them to be set
in sequence from either the full screen channel or the small screen in here.
- PIP: If you select PIP, the small screen channel shows in sequence. The main screen remains the same.
- Main: If you select the main, the PIP window remains unchanged but main screen is displayed in
sequence.
Note
PIP (Picture In Picture) : It means you can see the another small picture on the screen. It is similar to the
multi-vision.
d Display time
It is to set up the hang on time while sequencing the channel. The user can extend the hang on time of a
specific channel.
- Channel hang on time: OFF or, 01 ~ 30 seconds.
37
SPOT
The SPOT function enables to display a specific or, the entire channel in sequence on a separate monitor. It is
possible to set the channel hang on time as well.
By using two different monitors, one for the live and the other as a SPOT, specific or the full channel can be
displayed in sequence.
Note
SPOT OUT is always displaying one of the channels.
SPOT OUT
Rear panel
CCTV MONITOR
38
NETWORK
Network installation and diagram
b
Modem or Router
Internet
External Network
c
a
Topology for the Remote Control
This is the description for the system control and monitoring via network.
The remote control(monitoring) changes the system configuration or monitors the image via network (LAN).
Above is the necessary connection diagram.
a If the user subscribes to the internet, the internet service provider will connect it through a router or a
modem. The dynamic IP address is set for the modem user and fixed IP address is set for the router user.
b Connect the internet to the DVR coming from the modem or router, and setup the NETWORK configuration.
c It is possible to control the system from the PC with a web browser or the remote client software program
installed.
Notes
• Dynamic IP : The subscribed internet line is shared among the users. Since it doesn’t have the fixed
address, it is hard to connect from the outside. But, it is possible if there is a server which is informed of
the address. LDV-S802 supports dynamic IP as well by the separate server management.
• Fixed IP : It has a specific and unique IP address in the world to connect the internet.
NETWORK configuration
After the installation according to the architecture drawing, the network on the system should be set to enable
the remote cotrol and monitoring possible.
39
> DHCP function
There are only dynamic IP users in the internet environment. The address is continuously changing since it
is not a static IP.
For example, if there is a house but the address is frequently changed, the mail can not be delivered in
normal way. So, whenever the address is changed, you have to ask a town office to trace it. The role of the
town office is the DHCP function.
The DHCP Server automatically traces and records the IP change whenever it can access the data. The
product, LDV-S802, operates as a dedicated DHCP server.
Notes
• The dynamic IP user selects the DHCP “ON” and connects to the following site http://www.lg-securitys800.com and logs -in for the remote monitoring.(How to register membership to use is explained on
the above site).
• The NETWORK light on front panel only blinks when the system is connected by the user. Therefore it
will not blink when simply connected to the internet.
> IP INFORMATION SETUP
It is used when the network connection use static IP. The dynamic IP user doesn’t have to make configurations.
Fill it with ISP information provided to setup the static IP for use.
For example :
- IP ADDR: 192.168.123.51
- SUBNET: 255.255.255.0
- GATEWAY: 192.168.123.254
- DNS: 168.126.63.1
Notes
• IP Address
This is the unique name of device in TCP/IP network. This is an expensive internet line which is normally
used for servers. If you are using a static IP, enter the IP address.
• Subnet Mask
Has 32Bit length figures to decide the number of bits used as network address in IP address (= Address
mask)
• Gateway
Used to combine protocols or different architectures of network.
• DNS
Instead of the address being composed of numbers (ex. 168.126.063.001), this makes the connection
with easily memorable letters or words like a domain.
• To input the IP, it should be done by the direction key because the numeric key is not available.
> PORT
Configure the network port. And the changed port should be applied if the system is not connected even
after the configuration. User may consult to administrator or service provider if the port is being used by
another system or blocked at the router (factory default port: 5000).
40
> NETWORK PASSWORD
This is the password setup to check the user level when connecting the network by client software or web
browser. (the authority level is different from that of the user)
- ADMIN: System access to control all the functions including Setup, Search, Control and etc.
- USER 1~3: Only allows monitoring (no access to Setup or control and etc.).
41
> NOTIFICATION
It is an E-mail notice function when events happen (Alarm, Sensor, Motion detection, video loss, Power Off
or Password change). It is a very convenient function to notify the system information even if the user is not
in the local area.
- E-MAIL SETUP: Email information setup.
- E-MAIL NOTIFACATION: To select which event and how often the system sends an email.
[1] E-MAIL SETUP
a
b
c
a SMTP SERVER
To assign the email sending server, enter the email server address. It requires email address (SMTP)
registration. User may check out the information with email service provider.
b PORT
Most mail servers use ‘25’ as the port number. However port no. should be checked when system
doesn’t send the notification after configuration.
c MAIL ADDRESS
Enter the user’s email address.
Note
Use direction key to select menu. Use “T” key to delete typed letters.
42
[2] E-MAIL NOTIFICATION
a
b
c
d
f
e
a ALARM ON
Setup the email notification On/Off and time. The time setup is for the interval of sending the e-mail
- ON: Enable email notification.
- OFF: Disable email notification.
- Time configuration: Setup the time for sending notification in every 10mins/30mins/1hr/12hrs/1day.
Note
If the user selects to enable the E-mail notice “ON” and time as “10minutes”, it will send the e-mail
when the event occurs. But, if the event occurs again within 10minutes, the system will not send the
notification until this assigned time is elapsed. It will send the mail after that.
b SENSOR ON
Select whether the system send notification when Sensor event is occurred.
- ON: Enable email notification.
- OFF: Disable e-mail notification.
- Time configuration: Set the time for sending notification in every 10mins/30mins/1hr/12hrs/1day.
c MOTION DETECT
Setup the e-mail notification On/Off and time when the motion is detected.
- ON: Enable email notification.
- OFF: Disable e-mail notification.
- Time configuration: Set the time for sending notification in every 10mins/30mins/1hr/12hrs/1day.
d VIDEO LOSS
Setup the e-mail notification On/Off when the video signal is lost.
- ON/OFF: To enable or disable.
e ADMIN PW CHANGED
Setup the e-mail notification On/Off when the admin password changes.
- ON/OFF: To enable or disable.
f POWER ON
Setup the e-mail notification On/Off when the system power On.
- ON/OFF: To enable or disable.
43
> MAC ADDR
An address is necessary for computers to identify one after another on the network. Like we exchange
letters by writing sender’s and receiver’s address on envelope, Mac address is used as same way as the
postal address for network communication. And this will enable computers to exchange information on network. Mac address represents the current address of DVR. It is not necessary to change, but the user may
notify the system that the network is connected.
> SERVER
Unlike fixed IP, floating IP doesn’t have fixed IP address. It is changed whenever the modem is reset or
the power is turned on again. DDNS server keeps the time for the time changing IP information. When IP
address is set, DVR will keep DDNS and the user will register this DDNS server in order to search the DVR
though the IP address keeps being changed.
- Static IP user : DNS FAILED → It is regarded as a normal since fixed IP user doesn’t need the DDNS
server.
- Dynamic IP user: DNS AVAILABLE → It indicates system is network connected since Dynamic IP user
need DDNS server.
CHANNEL
It is the setup for Record, Record schedule, Title, Screen adjustment, PTZ. Since this part is one of the most
important parts of the setup, be especially careful about it.
44
RECORD
a
b
c
It is the setup for record resolution and frame rate of each channel. Since the resolution and picture quality are
different by the setting, you must be very careful.
a PICTURE SIZE
It sets the video resolution. The frame rate depends on the resolution.
The higher resolution , the lower frame rate while the lower the resolution, the higher the frame rate.
[Table 1-1]
Resolution
Frame Rate (NTSC)
Resolution
Frame Rate (PAL)
720 x 480
7.5 F/S
720 x 576
6.25 F/S
720 x 240
15 F/S
720 x 288
1.25 F/S
360 x 240
30 F/S
360 x 288
25 F/S
Note
Frame rate: It means the number of video images per second. If there are 30 video images per second, the
recorded video looks natural.
b PRERECORDING
It is for the prerecording setup. If this function is not used, the event recording has no meaning. If the object
has already passed but the recording started after, we cannot distinguish(analyze) the situation correctly.
Therefore, the system should have the image before the incident happen as an evidence.
- LDV-S802 has the recorded video image before 5seconds but, it depends on the resolution and frame
rate.
Note
Prerecording function.
If the recording is setup by the Motion Detection, the DVR starts recording after the door opened. If the
intruder went through the door in a very short time, his image will not be recorded in the DVR. That’s why
the prerecording is necessary. Since the DVR has the image before recording, if the actual recoding starts,
and the pre image is saved on HDD as well as the evidence.
c The frame rate, picture quality and audio recording as per the channel can be selected.
Please refer to the [Table 1-1].
[Picture quality]
LOWEST
<
|← Low quality
LOW
<
|
NORMAL <
Middle
|
HIGH
<
BEST
Good quality →|
45
RECORD SCHEDULE
a
b
c
e
f
g
d
It sets up the reserved recording by day or time.
a Select the day of week.
b Select the start and end time of each channel to be recorded as per each different event.
c NEXT
It moves to next page.
d PRE
It moves to the previous page.
e PAGE
It shows the current LIST page.
f COPY NEXT DAY
To apply the same setting to the other day, select the COPY NEXT DAY and select the day for applying the
same setup.
g COPY ALL
To apply the same setting to the whole day, please use this.
46
CAMERA TITLE
A
B
This is the setup for camera name. If you click the channel from the picture A, the virtual keyboard will be displayed to enter the name as per the picture B. Use the direction key to enter the name.
- To save: Select “ENTER”
- To delete, Select "←".
47
VIDEO ADJUST
There are many different kinds of cameras and the image varies such as bright or dark. To see the most
desirable camera images, you can setup the color configuration here.
A
B
To compensate the color, select the channel as per the picture A. The control window is displayed on the
image B of the currently selected channel to adjust the color. Setup the contrast, bright, saturation, hue for the
desired image.
Notes
• Hue: Adjusting the color green and red.
• Saturation: Saturation of color.
• Contrast: Adjusting the contrast of white and black.
• Bright: Adjusting the Brightness of color.
48
PTZ
The PTZ camera can be controlled by this system without any extra equipment. RS-485 communication is
used for PTZ camera control and ID is given for parallel connection.
It is easy to set up this system and control the PTZ by seeing its movement through the monitor.
> PAN/TILT camera connection diagram
For multi connection of Pan/Tilt camera, please refer to the following diagram.
RS-485 Control Line
ID 1
ID 2
ID 3
ID 4
PAN/TILT CAMERA CONNECTION DIAGRAM
49
> PTZ camera connection and settings
•
PAN/TILT camera setup
1. Connect the control terminal (RS-485) between camera and DVR.
2. Set the camera ID independently among 1-99.
3. Turn on the power to check whether the DVR displays the video image.
POWER
ID Setup
Video In
DVR
Video Out
PAN/TILT camera
Note
The connection could be different by the PTZ model so, please refer to the product manual.
•
DVR setup
1. Press the SET UP button on the front panel to go to PTZ on the CHANNEL menu.
2. As shown at the below, configure PROTOCOL, ID, BAUD on the channel with PTZ installed.
Note
Baud configuration
To configure RS-485 Baud RATE as PTZ transmission speed for each channel, Please refer to PTZ
specification.
50
•
Using the PAN and TILT
E
B
C
D
F
A
G
1. Press PTZ (A) button to display the PTZ menu.
2. Select the channel (B) with PTZ installed.
3. Press C to select the function among PAN/TILT, zoom and FOCUS then adjust each function using
D, E, F, G buttons.
4. Press the button A to exit the PTZ.
Notes
• Supported PTZ camera models.
- PELCO-D
- PELCO-P
- LG MULTIX
- LG SD168
• Supported model may be added for improving the performance without any notice.
51
EVENT
‘EVENT’ menu sets alarm, sensor and motion, which is the advanced feature not part of the general CCTV
features. When setting the recording by event, the mass storage device may not be necessary. If the user uses
this feature well, the DVR feature can be also maximized with the low capacity storage device only.
ALARM / SENSOR
Sensor4 Sensor3
Alarm
connection
Sensor2 Sensor1
Input
It has four SENSOR IN terminals for connecting the external sensor. According to SENSOR IN, Recording ON/
OFF and Alarm Out operation can be set.
Note
The alarm output of the system is 1A 24V DC / 0.5A 125V AC.
52
ALARM / SENSOR SETUP
Sensor and Alarm/Sensor can be set by pressing SET UP button and then moving to EVENT.
> ALARM MODE
Select the event type by using the direction keys to set the signal transmission to alarm output.
- OFF: Alarm Out Off.
- SENSOR : Alarm out when an event is triggered by the sensor.
- MOTION : Alarm out when the motion is detected.
- SENSOR + MOTION : Alarm out by the sensor or the motion detection.
> ALARM DWELLTIME
Configure the duration for generating the alarm.
- OFF: Disabled. (It disables the Alarm Output by setting the alarm on and the dwelling time off.)
- 1 second - 30 minutes: The user can set it from 1 second to 30 minutes using the arrow keys.
Note
The Alarm Dwelltime is to control the time for the external device. It is not the built-in buzzer of the system.
The setup of alarm dwell time should be more than 2 seconds at least.
> EVENT DISPLAY
Select the display type on the monitoring screen when an event (sensor or motion) is detected.
- NONE: No change.
- SEQUENCE: The channel with the event is displayed on the full screen (POP UP), and if an event
occurs on at the other channel, these channels are sequentially displayed.
- SPLIT: It displays with the split screen when an event is occurred.
53
> EVENT RECORD
Set whether to record or not and the recording time when an event occurs.
- OFF: No record on event.
- 1sec - 30mins: The user can select the recording time from 1sec to 30mins by the direction key.
Note
EVENT RECORD
If it is set to OFF, it doesn't record anything. So, you should be careful to set.
> EVENT BUZZER
Select relay On/Off and time of buzzer when an event occurs.
- OFF: No buzzer on event.
- 1 sec - 30mins: The user can select the buzzer output time from 1sec to 30mins by the direction keys.
> VIDEO LOSS BUZZER
Buzzer output when the incoming video signal is lost.
- ON: Generate the buzzer sound when the video signal is lost.
- OFF: No buzzer for the video loss.
Note
You can stop the buzzer sound using AUDIO button, which does not cancel the buzzer function If other
event occurs after buzzer stop, the buzzer function works as you set.
> SENSOR
Set the connection status of the sensor input.
- OFF: No operation.
- N.O (Normal open): The contact is normally opened but closed when the signal is generated.
- N.C (Normal close): The contact is normally closed but opened when the signal is generated.
54
Motion Detection
This is the representative function of the DVR system. It records for a specific time only when it detects the
motion. Also, the sensitivity can be selected, so it can record the motion from the sensitive motion to the large
movements through control.
A
B b
> CH (Channel)
Select the channel to detect the motion.
> ZONE
- ALL : The motion detection applyies to the whole area.
- OFF: Disabled.
- AREA: Select the area to be recognized.
[Set up]
The motion zone is displayed on the selected area as shown at the picture B. Select the area by moving
the cursor. If any movement is detected within the selected zone, it starts recording.
(1 CHANNEL Button: Select the whole area. 2 CHANNEL Button: Release the whole area.)
> SENS
Set the sensitivity of movement.
- Sensitivity: 1 (The highest sensitivity) - 5 (The lowest sensitivity)
55
How to search
Different from the general time of VCR, it can record longer and search with the desired condition, which
enables easy image search without spending all-day-long. It can search using various methods such as
desired time, motion and recording via sensor. Because it is frequently used, it is better for you to get familiar
with it.
Using the SEARCH button
To search the video file, press the “SEARCH” button.
DATE & TIME Search
A
b
B
As shown on the image A, select “1. DATE&TIME” to float next search window as image B shows, and after
selecting “DATE&TIME” on the menu, finally confirm by selecting “ SEARCH” to start playback. It displays “No
DATA” when no recorded data is available.
The user can search the video image by the desired date/time selection.
56
How to control the search speed
The icon changes according to the
searching speed.
-x1:B
-x2:B>
- x 4 : B >>
- x 8 : B >>>
- x 16 : B >>>>
The recorded images that matches the selected date and
time are displayed as shown at the above.
a
b
There are couple of search modes such as fast forward search and backward search, etc.
a m (Backward search) : Each press of this button changes the search speed (X2 → X4 → X8 → X16).
b M (Forward search) : Each press of this button changes the search speed (X2 → X4 → X8 → X16).
57
EVENT Search
It searches by a certain event (motion, sensor, etc.), which is the most commonly used one in the field. If you
want to search for an image, it can make the search faster rather than doing it by date or time.
The event search is possible based on the date and kind of events.
Selecting the event
-
Video loss : Searches for the lost video.
Emergency : Searches for the video with the emergency button operated.
Continue : Searches for the video recorded by the schedule.
Motion : Searches for the video with any motion detected.
Sensor : Searches for the video recorded by the sensor.
All : It searches for the video by all events.
Notes
• The number of event logo that can be created goes up to 1 million.
• Searching for the desired image depends on the field condition.
If the location is only for the safe, the Motion detection will be better but, if it is a door, the sensor triggered
recording will be better. Therefore, use the suitable event recording depending on the situations.
Search for the first record
It searches for the oldest one recorded at the storage device.
Search for the last record
It searches for the latest one recorded at the storage device.
58
AUDIO
How to use the audio buttons
Select the channel to listen to and press the “AUDIO” button on the front panel.
Notes
It is the same either for Live or Search.
How to listen to the audio channel
When it shows the AUDIO control box, press the channel to listen to for both Live and Search.
- OFF: No Audio.
- CH1: Listen to Ch1.
- CH2: Listen to Ch2.
- CH3: Listen to Ch3.
- CH4: Listen to Ch4.
- Automatic: Listening to the audio of the selected channel when selecting the entire screen
(1, 2, 3, 4 buttons on the front panel).
59
EMERGENCY
Emergency button is for the emergency recording as it is described.
If an intruder comes in, but the DVR is under scheduled recording which may not be recorded at that time,
press the “EMERGENCY” button for the immediate recording regardless of the record setting.
Note
Deselecting Emergency recording
When the event is over, you should off the emergency recording by pressing the same button, otherwise it
keeps manual recording whatever the previous setting was. When the function is deselected, it automatically
resumes previous setup.
SCHEDULE
If the user press the SCHEDULE button, it starts record as per the setup of “SCHEDULED RECORD”and if
you press it again, the setup becomes OFF.
Note
Although the user setup the “SCHEDULED RECORD” from menu, if you don’t press “SCHEDULE” button, it
doesn’t record. To make a record, you have to press either “SCHEDULE” or “EMERGENCY” button.
60
REMOTE SOFTWARE
External Network
Internet
DDNS server
Internet
Internal Network
< System network composition >
It externally monitors the video or control setting via internet. Methods for access in externally include using
remote software and access on the web browser. As shown at the above system network composition diagram,
when it connects to the system via internet, the system searches for the DDNS SERVER and the SERVER
memorizes the information of the local DVR. Whether you try to connect local DVR on web browser or remote
software, DDNS SERVER will automatically find out the DVR information and connect each other.
61
Remote software installation and PC requirement
Install remote software using provided program CD. You are requested to install the software (LDV-S802.EXE)
which is exclusively for PC.
PC Requirements
Recommended PC Requirements
• CPU : Pentium IV 1.2GHz or higher.
• CPU : Pentium IV 2GHz or higher.
• Memory : 256MB or higher.
• Memory : 512MB or higher.
• VGA memory : 32M or higher.
• VGA memory : 64M or higher.
• HDD : 5G or more.
• HDD : 10G or more.
• DirectX 8.1 or higher is installed.
• DirectX 8.1 or higher is installed.
It is automatically installed by clicking as shown above and the icon is created at the Windows desktop screen.
62
How to use remote software
When the installation is completed, click LG logo icon on Windows desktop screen to execute the remote software.
> Connection
Click
icon, “LDV-S802 Client” on Windows background screen.
b
a
a
Login icon: When clicking to connect, “LOGIN” window is open.
b
Account information: Enter the account information as shown below.
A. Static IP user connection
A
•
•
•
•
•
Site : Up to max. 4 units registration per system.
IP/DNS : Enter the static IP address.
PORT : Enter the System port info (Default: 5000).
ID : Enter the ID (Administrator: ADMIN).
PWD : Enter the password (Default: 0000).
B. Dynamic IP user connection
B
Note
When you connect 4 different
systems as a multi-connections,
select ‘ALL’ from ‘Site’ clause.
•
•
•
•
Use : Mark “Use”.
LDV-S802 WEB Info. : Click to open.
http://www.lg-security-s800.com site.
Note
It requires membership registration and system information registration. Refer to website for details.
ID : ID information (Administrator: ADMIN).
PWD : Password information (Default: 0000).
63
> Screen and Buttons
c
d
a
e
f
b
a Screen test display
-
Ch4: It indicates channel no. (Current video image on the screen is fourth camera video)
Live: It indicates that the current display is in live images. “Rec” will be displayed when it is the
backup data.
Time (21:57:39): It shows Hour : Minutes : Seconds of displaying camera channel.
b DVR select
On remote software, max. 4 DVRs can be connected. As per initial DVR setup, each selection will
display the relevant DVR channel.
64
c LIVE mode display
- Live: It indicates that it is in Live mode display.
- SEARCH: It indicates that it is in Search mode display.
Note
It doesn’t provide audio function when it is in Live mode.
d Disconnection
Disconnect network connection.
e Adjusting the PTZ
A.
B.
C.
D.
A
B
C
(v V b B) : Adjust the direction of the PTZ camera.
Channel NO : It shows selected channel NO.
ZOOM : It is zoomed in/out by the PTZ lens.
FOCUS : The focus of the PTZ may be adjusted.
D
f Program shutdown
This is to shutdown remote program after confirming message.
65
> Setting the remote system
LDV-S802 may be remotely set. The user can remotely modify the setting without going to the location of
the system.
Click “Setup” to remotely set the system as shown at the left.
[1] Record setup
See page 45 for the terms and the details because it is done in the same way as the system.
a
b
c
d
e
a Picture size
Set the resolution of the recorded image.
b Prerecording time (5sec.)
It starts recording 5 seconds before the event.
c Quality
Selecting the quality of the recorded image.
d Frame rate
Select the number of recorded frames per second.
e Audio
Select to record the audio by channel.
Note
Recording frame rate against each resolution is fixed, so Apply button will not be activated if frame rate and
resolution are not matched.
Resolution Frame Rate (NTSC)
66
Resolution
Frame Rate (PAL)
720 x 480
7.5 F/S
720 x 576
6.25 F/S
720 x 240
15 F/S
720 x 288
1.25 F/S
360 x 240
30 F/S
360 x 288
25 F/S
[2] Schedule record setup
a
b
c
d
e
f
g
a Date selection
Select date of schedule.
b Time setting
Set per each time schedule.
c Channel selection
Select channel.
d Event setting
Select event you will apply.
Note
Event selecting...!
- NONE: No recording.
- CONTINUOUS: Continuous recording.
- MOTION: Recording on motion detection.
- SENSOR: Recording on sensor trigger.
e Pre page / Next page
Time is listed by 24-hour. Click Pre page or Next page buttons to move to previous or next page.
f Copy next day
If you want to apply the same setting to another day, select the COPY NEXT DAY and then the day
of a week to copy the same schedule.
g Copy all
Select it to copy this setting to the whole day.
67
[3] ALARM/SENSOR SETUP
a
b
c
d
a Alarm mode (Alarm relay out select)
Select the event type by using the arrow keys to set the signal transmission for alarm output.
Note
Event selecting...!
- OFF : No alarm relay out.
- SENSOR : Alarm relay out by sensor trigger.
- MOTION : Alarm relay out by motion detection.
- SENSOR + MOTION : Alarm relay out by either motion detection or sensor trigger.
b Alarm dwell time
Configure the duration of the alarm. (0 sec ~ 30 minutes)
c Event record
Set whether to record or not and the recording time when an event occurs. (OFF ~ 30minutes)
d Sensor type
Set connection status of the sensor input.
- N.O (Normal open): The contact is normally opened but closed when the signal is generated.
- N.C. (Normal close): The contact is normally closed but opened when the signal is generated.
68
[4] MOTION SETUP
Motion setting cannot be changed on client software as allowed on local DVR menu.
69
[5] VIDEO ADJUST setup
a
b
c
d
There are various types of cameras and the image also has many dark or light points.
This function compensates the spots to create optimized image through color adjustment by channel.
a Hue : Control the entire color by green or red channel.
b Sat : Display the saturation of a color.
c Con : Control the contrast of the image.
d Bri : Control the brightness of the image.
70
[6] HARD DISK setup
a
b
You can remotely change whether to record in the storage device and the record sequence.
a Overwrite: Set to overwrite the storage device.
b Record HDD: If two hard disks are installed, you can change the record sequence.
-
HDD1 : Record the HDD1 only even if there are two HDDs (HDD1, HDD2).
-
HDD2 : Record the HDD2 only even if there are two HDDs (HDD1, HDD2).
-
HDD1, 2 : Record the HDD1 first and then the HDD2.
Caution
•
•
If the HDD is incorrectly set, it will not start recording.
The menu setup is not available when recording.
71
> How to remotely search
LDV-S802 can remotely do a search and it is possible to search by date, time or event.
(Reference: The search speed may be slowed down depending on the Internet speed.)
Click “Search” for the method on how to remotely monitor as shown
at the left figure.
a
b
c
d
e
f
The buttons to search are displayed at the bottom of the remote software as shown in the above figure.
a DATE button
Click the DATE button to open the electronic calendar for the user to select data as shown at the below.
A
D
B
C
Note
Search will be cover all the channels.
Search channel selection → Event type selection → Search:
the result will bring out not only event list of selected channel, but bring out event list of all the channels
if event channel is included.
72
[Steps]
1. Select one of below A - C search types.
A Search by date: Select date you want to search and click “Search".
B Search by Event: Select event you want to search and click “Search".
- ALL: All events.
- Continue: Data recorded by continuous recording.
- Motion: Data recorded by motion detection.
- Sensor: Data recorded by sensor triggered recording.
- Emergency: Data recorded by emergency recording.
- Video loss: When video input signal is lost.
C Search by Time and date.
2. It brings out searched list as D on the image.
- Date: Displays the recorded date.
- Time: Time display.
- Channel: Channels containing recorded data.
- Event: It describes type of event.
b REW button
To reverse playback recorded date in rapid speed.
c STOP button
To stop playbac.
d PLAY button
To playback recorded data in normal speed.
e FEW button
To playback recorded date in rapid speed.
f AUDIO ON/OFF (Listening to audio data)
To listen to audio of recorded data during playback.
Caution
How to use playback button
• It is set to normal speed (PLAY) for playback search mode or for playing back the back up file data, and
for Fast forward playback by FEW and reverse playback by REW.
• Network condition may affect FEW and REW playback speed and cause no screen display.
73
> Remote backup
LDV-S802 provides remote backup function searching date, day, time or event. (Note. Search speed may
go slow depending on network condition).
Click “Search” for the method on how to remotely monitor as shown
in the left figure (Searching the data must be done in advance).
[Steps]
1. Search data for backup (See page 72).
2. Click on the “Backup” button for the data you want to capture during play back.
3. As shown below, it will suggest Year and time as backup file name, and click “OK” to start the
backup.
4. It displays “Rec / AVI backup” when backup starts.
5. Backup is completed when you click on the “Backup” button again. (Example, Click backup button
after 5 minutes if you want to obtain 5 minutes length backup data.)
74
> Backup data search
This is to search the data obtained by USB memory stick. This function is not available on local DVR but
provided on remote software.
• Connect USB memory stick to PC.
1. On the remote program screen, click on the right button to open “File Open".
2. Browse the data, “LDV-S802 XXXX.DVR” in the USB memory stick and click it to open the file.
75
3. It reviews the playback data.
[How to search]
• m (REW) : To reverse playback recorded data in rapid speed.
• x (STOP) : Stop playback.
• N (PLAY) : Playback.
• M (FEW) : To playback recorded data in rapid speed.
• Audio icon : Listening to audio data (It shows red border when the channel is selected by mouse).
Web monitoring login
Web-monitoring is to simultaneously control and monitor max. of 4 DVR systems through web browser
(Internet explorer) of internet connected PC.
For more detailed information about Web-monitoring, visit the website
http://www.lg-security-s800.com.
Note
Functionality of Web-monitoring is subject to change for providing better function.
76
Appendix
Default settings
Remote ID
Mouse Resolution
Language
Date Format
Time Correction
Daylight Saving
1111
Overwrite
Record HDD
Auto Delete
1
1
English
YYYY/MM/DD
+00Sec/Mon
Off
Backup
Backup Channel 1-4
On
Button Lock
Off
Display
Time
Date
Title
Transparency
Border Color
Display Position
Information
Time/Date
System
Password
Hard Disk
OSD
Display
Split Mode
Auto Sequence
Auto Loss Skip
Sequence Mode
Pip Sequence
Display Time
CH1-4, Split
Spot
Display Time CH1-4
DHCP
Off
IP Addr
192.168.1.50
Subnet
Gateway
Dns
Port
255.255.255.0
192.168.1.1
168.126.63.1
5000
Level
Admin
User1
User2
User3
Network
Password
Network
E-Mail Setup
Notification
E-Mail Notification
On
HDD1-2
Off
On
On
On
On
Off
White
D
Quad-1
On
Full
Pip
3sec
3sec
ID
ADMIN
USER1
USER2
USER3
SMTP Sever
Port
Password
0
0
0
0
MAIL. KOREA. NET
25
Alarm On
Sensor On
Motion Detection
Video Loss
Admin PW Changed
Off/10MIN
Off/10MIN
Off/10MIN
Off
Off
Power ON
Off
77
Record
Record
Schedule
Channel
Camera Title
Video Adjust
PTZ
Alarm/Sensor
Event
Motion
Detection
Etc
Audio OUTPUT
Picture Size
Prerecording
Channel
CH1
CH2
CH3
CH4
Time
00:00 - 00:00
Channel
CH1
CH2
CH3
CH4
Channel
CH1
CH2
CH3
CH4
Channel
CH1
CH2
CH3
CH4
Alarm Output
Alarm Dwelltime
Event Display
Event Record
Event Buzzer
Video Loss Buzzer
Sensor CH1-4
Channel
CH1
CH2
CH3
CH4
Off
360X240
Off
Quality
Normal
Normal
Normal
Normal
Channel
CH1
Title
CAM1
CAM2
CAM3
CAM4
Hue
50
50
50
50
Protocol
PELCO-D
PELCO-D
PELCO-D
PELCO-D
SEN+MOT
10sec
None
30sec
Off
Off
Off
Zone
Off
Off
Off
Off
Note
The language is set to English when the system is initialized.
78
Frame
15F/S
15F/S
15F/S
15F/S
Event
NONE
Audio
Off
Off
Off
Off
Sat
50
50
50
50
ID
0
0
0
0
Con
50
50
50
50
Baud
1200
1200
1200
1200
Sensitivity
3
3
3
3
Bri
50
50
50
50
The table of menu setup applying time
This is the list of immediately applied function after menu setup and the one applied after escaped from the
menu.
Information
Time/Date
System
: Immediately applied menu.
Password
Hard Disk
Backup
Button Lock
OSD
Display
Remote ID
Mouse Resolution
Language
Date Format
Time Correction
Daylight Saving
: Applied after escaping.
Overwrite
Record HDD
Auto Delete
Backup Channel 1-4
Display
Time
Date
Title
Transparency
Border Color
Display Position
Split Mode
Auto Sequence
Spot
Auto Loss Skip
Sequence Mode
Pip Sequence
Display Time
CH1-4, Split
Display Time CH1-4
DHCP
IP Addr
Subnet
Gateway
DNS
Port
Network
Password
Network
Level
Admin
User1
User2
User3
E-Mail Setup
Notification
E-Mail Notification
SMTP Sever
Port
Mail Address
Alarm On
Sensor On
Motion Detection
Video Loss
Admin PW Changed
Power ON
79
Picture Size
Prerecording
: Immediately applied menu.
Channel
Record
CH1
CH2
CH3
CH4
Record
Schedule
Time
00:00 - 00:00
Channel
CH1
Channel
Camera Title
CH2
CH3
CH4
Channel
CH1
Video Adjust
CH2
CH3
CH4
Channel
CH1
PTZ
CH2
CH3
CH4
Alarm Output
Alarm Dwelltime
Event Display
Alarm/Sensor
Event Record
Event Buzzer
Video Loss Buzzer
Event
Sensor CH1-4
Channel
CH1
Motion
Detection
CH2
CH3
CH4
Etc
80
Audio OUTPUT
: Applied after escaping.
Models compatible with the USB
The following is the list of compatible USB memory sticks and the HDD devices for the LDV-S802 product.
Other models may be also compatible and the names of the verified products are as follows:
•
Verified USB memory stick
COMPANY
•
MODEL NAME
CLIP DRIVE
RUF Series
HUMANCC
CELLINK Series
LG
XSTICK Series
USBMDRIVE
MP Series
I-ROCKS
I-ROCKS Series
IMATION
IFLASHEX Series
SARATECH
FD Series
Verified HDD device
Manufacturer name
Remarks
MAXTOR
WD
The capacity of 250G or less is possible
and we recommend the 250G HDD.
HITACHI
Notes
• The HDD should be formatted before use.
• The HDD should be formatted to use when it is newly installed or added.
81
HDD storage capacity table
Resolution
(NTSC/PAL)
Quality
Lowest
Low
360x240
/
360x288
Normal
High
Best
82
FPS
(NTSC/
PAL)
Aver.
Frame size
(byte)
BPS
(Kbytes/
sec)
(NTSC/PAL)
Audio Size
(kbytes/
sec)
HDD
size(GB)
30/25
1024
30/25
2
250
15/12.5
1024
15/12.5
2
250
1157/1389
1021/1197
7.5/6
1024
7.5/6.25
2
250
2315/2778
1827/2104
3/3
1024
3/3.12
2
250
5787/5564
3472/3391
1/1
1024
1.5/1.5
2
250
11574/11574
4960/4960
Recording Time (Hr)
Video
(NTSC/PAL)
Video+Audio
(NTSC/PAL)
579/694
543/643
30/25
2048
60/50
2
250
289/347
280/334
15/12.5
2048
30/25
2
250
579/694
543/643
7.5/6
2048
15/12.5
2
250
1157/1389
1021/1197
3/3
2048
6/6.24
2
250
2894/2782
2170/2107
1/1
2048
3/3
2
250
5787/5787
3472/3472
30/25
4096
120/100
2
250
145/174
142/170
15/12.5
4096
60/50
2
250
289/347
280/334
7.5/6
4096
30/25
2
250
579/694
543/643
3/3
4096
12/12.48
2
250
1447/1391
1240/1199
1/1
4096
6/6
2
250
2894/2894
2170/2170
30/25
6144
180/150
2
250
96/116
95/114
15/12.5
6144
90/75
2
250
193/231
189/225
7.5/6
6144
45/37.5
2
250
386/463
369/440
3/3
6144
18/18.72
2
250
965/927
868/838
1/1
6144
9/9
2
250
1929/1929
1578/1578
30/25
8192
240/200
2
250
72/87
72/86
15/12.5
8192
120/100
2
250
145/174
142/170
7.5/6
8192
60/50
2
250
289/347
280/334
3/3
8192
24/24.96
2
250
723/696
668/644
1/1
8192
12/12
2
250
1447/1447
1240/1240
Resolution
(NTSC/PAL)
Quality
Lowest
Low
Normal
720x240
/
720x288
High
Best
Lowest
Low
720x480/
720x576
Normal
High
Best
FPS
(NTSC/
PAL)
Aver.
Frame size
(byte)
BPS
(Kbytes/
sec)
(NTSC/PAL)
Audio Size
(kbytes/
sec)
HDD
size(GB)
15/12.5
3072
45/37.5
2
250
7.5/6
3072
22.5/18.75
2
250
772/926
709/837
3/3
3072
9/9.36
2
250
1929/1855
1578/1528
Recording Time (Hr)
Video
(NTSC/PAL)
Video+Audio
(NTSC/PAL)
386/463
369/440
1/1
3072
4.5/4.5
2
250
3858/3858
2671/2671
15/12.5
6144
90/75
2
250
193/231
189/225
3/3
6144
18/18.72
2
250
965/927
868/838
1/1
6144
9/9
2
250
1929/1929
1578/1578
15/12.5
8192
120/100
2
250
145/174
142/170
7.5/6
8192
60/50
2
250
289/347
280/334
5/5
8192
36/38
2
250
482/457
457/434
3/3
8192
24/24.96
2
250
723/696
668/644
1/1
8192
12/12
2
250
1447/1447
1240/1240
15/12.5
10240
150/125
2
250
116/139
114/137
7.5/6
10240
75/62.5
2
250
231/278
225/269
5/5
10240
45/47.5
2
250
386/365
369/351
3/3
10240
30/31.2
2
250
579/556
543/523
1/1
10240
15/15
2
250
1157/1157
1021/1021
15/12.5
14336
210/175
2
250
83/99
82/98
7.5/6
14336
105/87.5
2
250
165/198
162/194
5/5
14336
63/66.5
2
250
276/261
267/253
3/3
14336
42/43.68
2
250
413/397
395/380
1/1
14336
21/21
2
250
827/827
755/755
7.5/6
6144
45/37.5
2
250
386/463
369/440
3/3
6144
18/18.72
2
250
965/927
868/838
1/1
6144
9/9
2
250
1929/1929
1578/1578
7.5/6
8192
60/50
2
250
289/347
280/334
3/3
8192
24/24.96
2
250
723/696
668/644
1/1
8192
12/12
2
250
1447/1447
1240/1240
7.5/6
10240
75/62.5
2
250
231/278
225/269
3/3
10240
30/31.2
2
250
579/556
543/523
1/1
10240
15/15
2
250
1157/1157
1021/1021
7.5/6
12288
90/75
2
250
193/231
189/225
3/3
12288
36/37.44
2
250
482/464
457/440
1/1
12288
18/18
2
250
965/965
868/868
7.5/6
14336
105/87.5
2
250
165/198
162/194
3/3
14336
42/43.68
2
250
413/397
395/380
1/1
14336
21/21
2
250
827/827
755/755
Note
This table value is reference only. The table value may differ depends on your environment.
83
The estimation of backup speed
Setup
Record
Resolution
360x240
Picture quality
Normal
(CH1, CH2, CH3, CH4 all same)
Frame rate
30 F/S
(CH1, CH2, CH3, CH4 all same)
Channel
CH1, CH2, CH3, CH4
Time scope
60 minutes
Backup
Tested result
84
Total capacity
1.2G
The search time of HDD capacity
25 minutes 36 seconds (828 KB/S)
USB saving time
45 minutes 2 seconds (471 KB/S)
Total required time
1 hour 10 minutes 38 seconds
Specifications
Model
LDV-S802
Input
Video
Output
Audio
Alarm
4
Loop Through
4
composite
1
S-Video
1
VGA
1
Spot
1
Input
4
Output
1
Input
4
Output
1
Pre-Alarm Recording
Yes
Up to 120 fps @ 360x240
NTSC
Recording
Up to 60 fps @ 720x240
Up to 30 fps @ 720x480
Image Rate
(/Sec)
Up to 100 fps @ 360x288
PAL
Up to 50 fps @ 720x288
Up to 25 fps @ 720x576
Search
Display
Playback Function
FF, FB, Frame Advance, 5Mins Skip
Search Mode
Date/Time, Event, Go to First, Go to Last
Image Rage
(/Sec)
PTZ
Network
Security
120 fps (Real time per each channel)
PAL
100 fps (Real time per each channel)
Division Mode
1, 4, PIP
(Quad-1,2,3, 3Way-1,2,3, 2Way-1)
Max Capacity
500GB (Up to 2 HDDs)
Backup Interface
USB 2.0 x1
Network
Supportable Devices
USB Memory Stick
Internal HDD
Backup
NTSC
PTZ Control Interface
RS-485 x1
Network Connection
Ethernet 10/100 M (RJ-45)
Network Transmittion Speed
Max. 120 fps @ 360x240
Password Protection
Yes
Power
DC 12V 5A 50/60 Hz, ADAPTER
Demension (WxDxH mm)
430 x 315.5 x 54
Weight (without HDD)
2.7 Kg
Operation Temp./Humidity
0°C ~ 40°C / 0%RH ~ 80%RH
85
P/NO: MFL30580128
Download PDF