LG | LK72B | LG LK72BE Owner’s Manual

OWNER’S MANUAL
Multimedia
Speaker System
Please read this manual carefully before operating
your set and retain it for future reference.
MODELS
LK72B (LK72B, LK72B-S)
LK72BE (LK72BE, LK72BE-S)
www.lg.com
MFL70428612
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
1807_Rev02
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, should be placed on the
apparatus.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not use high voltage products around
this product. (ex. Electrical swatter) This product may
malfunction due to electrical shock.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
NOTICE: For safety marking information including
product identification and supply ratings, please refer
to the main label on the bottom or the other surface
of the product.
Getting Started
CAUTION concerning the Power Cord
The Power Plug is the disconnecting device. In case
of an emergency, the Power Plug must remain readily
accessible.
Do not overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords, frayed
power cords, or damaged or cracked wire insulation
are dangerous. Any of these conditions could result
in electric shock or fire. Periodically examine the
cord of your device, and if its appearance indicates
damage or deterioration, unplug it, discontinue use of
the device, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord exits
the device.
This device is equipped with a portable battery or
accumulator.
How to Safely remove the batteries or the battery
pack from the equipment:
To Remove the old batteries or battery pack, follow
the assembly steps in reverse order. To prevent
contamination of the environment and bring on
possible threat to human and/or animal health, the
old batteries or the battery pack must be put in an
appropriate container at designated collection points.
Do not dispose of batteries or battery pack together
with other waste. It is recommended that you use
local, free reimbursement systems batteries or
battery packs, (may not be available in your area). The
batteries or the battery pack should not be exposed
to excessive heat such as sunshine, fire or the like.
CAUTION: No naked flame sources, such as lighted
candles, should be placed on the apparatus.
Symbols
~
Refers to alternating current (AC).
0
Refers to direct current (DC).
Refers to class II equipment.
1
Refers to stand-by.
!
Refers to “ON” (power).
Refers to dangerous voltage.
1
Getting Started
Check the specification page of this owner’s manual
to be certain of the current requirements.
3
4
Table of Contents
Table of Contents
1
Getting Started
2Connecting
2
6
7
7
7
7
8
9
10
Safety Information
Unique Features
Playable file Requirement
– Music file requirement
– Compatible USB Devices / SD cards
– USB device / SD card requirement
Remote control
Front panel
Rear panel
11
11
12
12
12
13
13
Power Cord Connection
Speaker Connection
Optional Equipment Connection
– AUX IN Connection
– PORT. IN Connection
– USB Connection
– SD card Connection
Table of Contents
3Operating
4Troubleshooting
14
14
16
16
20 Troubleshooting
20 – General
18
18
18
18
19
19
19
19
Basic Operations
– USB/SD Operations
Using BLUETOOTH® wireless technology
– Listening to music stored on the Bluetooth
devices
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
Other Operations
– Turn off the sound temporarily
– Auto power down
– Adjusting Bass level
5Appendix
21
22
22
22
General specifications
Trademarks and Licenses
Maintenance
– Handling the Unit
5
1
2
3
4
5
6
Getting Started
Unique Features
1
BLUETOOTH®
Getting Started
Listens to music stored on your Bluetooth device.
Portable In
Listens to music from your portable device. (MP3,
Notebook, etc.)
Getting Started
Playable file
Requirement
MP3 file compatibility with this unit is limited as
follows.
yy Sampling frequency : within 32 to 44.1 kHz
yy Bit rate : within 32 to 320 kbps
yy Maximum files : 999
yy Maximum folders : 999
yy File extensions : “.mp3”
yy Certain MP3 files may not be played depending on
the type or format of the file.
Compatible USB Devices / SD
cards
yy MP3 Player : Flash type MP3 player.
yy USB Flash Drive :
Devices that support USB2.0 or USB1.1.
yy SD card : SD, SDHC, SDXC
yy The USB / SD function of this unit does not
support all USB devices and SD cards.
USB device / SD card
requirement
yy Devices which require additional program
installation when you have connected it to a
computer, are not supported.
yy Do not extract the USB device / SD card while in
operation.
yy For a large capacity USB or SD card, it may take
longer than a few minute to be searched.
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
yy Using NTFS file system is not supported.
(FAT(16 / 32) and ExFAT file systems are
supported.)
yy This unit recognizes up to 999 files.
yy External HDD, Card readers, Locked devices, or
hard type USB devices are not supported.
yy USB port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
yy Some USB / SD cards may not work with this unit.
1
Getting Started
Music file requirement
7
8
Getting Started
Remote control
• • • • • • • • • • • • • • a• • • • • • • • • • • • • •
1 (Standby) : Turns the power on or off.
F (Function) : Selects the function and input source.
1
Getting Started
Input source /
Function
USB
Display
USb
SD card
Sd
AUX input
AUdIO
Portable input
POrtAbLE
AUdIO
Bluetooth
bt
Radio
* 87.50
* : Displays current radio frequency.
VOL (Volume) +/- : Adjusts speaker volume.
[(Mute) : Mutes the sound.
REPEAT : Listens to your files repeatedly or
randomly.
BASS +/- : Adjusts bass level.
• • • • • • • • • • • • • • b• • • • • • • • • • • • • •
C/V (Skip/Search)
- Skips backward or forward.
- Searches for a section within a file.
N (Play/Pause) : Starts or pauses playback.
TUNING-/+ : Selects the radio stations.
Replacement of battery
PRESETW/S : Chooses a preset number for a radio
station.
MEMORY : Stores radio stations. (Page 18)
DELETE: Deletes all the saved stations. (Page 18)
? : This button is not available.
Remove the battery cover on the rear of the remote
control, and insert the battery with 4 and 5
matched correctly.
Getting Started
9
Front panel
a
f
b
e
1
c
d
Getting Started
aRemote sensor
dVOL (Volume) -/+
bSD card slot
Adjusts speaker volume.
C/V (Skip/Search)
- Skips backward or forwards.
- Searches for a section within a file.
- Selects the radio stations.
N (Play/Pause)
Starts or pauses playback.
BASS -/+
Adjusts bass level.
You can play sound files by connecting the SD
card.
c1 (Standby)
Turns the power on or off.
F (Function)
Selects the function and input source.
Input source /
Function
USB
Display
USb
SD card
Sd
AUX input
AUdIO
Portable input
POrtAbLE
AUdIO
Bluetooth
bt
Radio
* 87.50
* : Displays current radio frequency.
eUSB port
You can play sound files by connecting the USB
device.
PORT. (Portable) IN
Connect a portable device.
fDisplay window
10 Getting Started
Rear panel
1
a
Getting Started
b
c
aAUX IN (L/R)
Connect an auxiliary device.
bFRONT SPEAKERS (FL/FR) connector
cPOWER IN
dFM ANTENNA
d
Connecting 11
Power Cord Connection
Speaker Connection
1. Connect one end of the power cord (included) to
the POWER IN.
Connect each speaker cable to the FRONT
SPEAKERS (FL/FR) jack.
2
Connecting
Right
2. Plug the other end into the wall outlet.
,,Note
Unplug the power cord from the wall outlet if
you do not use for an extended period of time.
Left
,,Note
yy When you connect the speakers to the unit,
make sure to connect the speaker’s cable and
plug to the corresponding speaker connector.
yy Be careful to make sure children do not put
their hands or any objects into the *speaker
duct.
* speaker duct : A hole for plentiful bass
sound on speaker cabinet (enclosure)
yy The speakers contain magnet parts, so color
irregularity may occur on the TV screen or PC
monitor screen. Please use the speakers far
away from either TV screen or PC monitor.
12 Connecting
Optional Equipment
Connection
PORT. IN Connection
Connect an output (earphone or line out) of portable
device (MP3 or PMP etc) to the PORT. IN (3.5 mm)
connector.
AUX IN Connection
Connect an output of auxiliary device (Camcorder, TV,
Player, etc) to the AUX IN (L/R) connector.
2
Connecting
If your device has only one output for audio(mono),
connect it to the left(white) audio jack on the unit.
3.5 mm stereo
cable
(Optional)
Red
White
MP3 player etc.
Listening to music from your portable
player or external device
The unit can be used to play the music from many
types of portable player or external device.
Red
White
1. Connect the portable player to the PORT. IN
connector of the unit.
Or
Connect the external device to the AUX IN (L/R)
connector of the unit.
2. Turn the power on by pressing 1.
3.Press F to select AUX or PORTABLE function.
4. Turn on the portable player or external device and
start it playing.
,,Note
DVD, Blu-ray player etc.
Automatically switches to the PORTABLE
function when you connect the portable device
to the PORT. IN connector.
When you select AUX or PORTABLE function,
“AUX” or “ ” appears on the display window.
Connecting 13
USB Connection
SD card Connection
Connect a USB device (or MP3 player, etc.) to the
USB port on the unit.
Connect a SD card to the SD slot on the unit.
2
,,Note
Removing the USB device from the unit:
SD card
,,Note
Removing the SD card from the unit:
1. Choose a different function.
1. Choose a different function.
2. Remove the USB device from the unit.
2. Remove the SD card from the unit.
Connecting
USB device
14 Operating
Basic Operations
,,Note
yy Repeat/Random playback operates as
follows.
USB/SD Operations
Description
Plays songs in order and stops
the playback.
2. Select USB / SD function by pressing F.
Plays a same song repeatedly.
To
Playback
Pause
3
On Diplay
1. Connect the USB device to the USB port.
Or connect the SD card to the SD slot.
Searching
for a section
within a file
Do this
Press N.
Press N during playback.
Press and hold C/V during
playback and release it at the point
you want to listen to.
Operating
Press V to go to the next file.
Skipping to
the next/
previous file
Playing in less than 3 seconds, press
C to go to the previous file.
Playing after 3 seconds, press C
to go to the beginning of the file.
Press REPEAT on the remote
control repeatedly, the display will
Playing
repeatedly or be changed in the following order.
randomly
(RANDOM)
Plays all the songs repeatedly.
(RANDOM)
Plays all the songs randomly
and repeatedly.
yy Do not extract the USB device or SD card
during operation. (play, etc.)
yy Regular back up is recommended to prevent
data loss.
yy
appeaers on the window windonw in
repeat/radom mode.
Operating 15
,,Note
yy Files are recognized as below.
*
3
Operating
yy File will be played from $ file No.1 to $ file
No.14 one by one.
yy Files will be presented in order recorded and
may be presented differently according to the
record circumstances.
*ROOT : the first screen you can see when a
computer recognize the USB / SD card are
“ROOT”
16 Operating
Using BLUETOOTH®
wireless technology
Listening to music stored on the
Bluetooth devices
About Bluetooth
Before you start the pairing procedure, make sure the
Bluetooth feature is activated on your Bluetooth
device. Refer to your Bluetooth device’s user guide.
Once a pairing operation is performed, it does not
need to be performed again.
Bluetooth is wireless communication technology for
short range connection.
The sound may be interrupted when the connection
interfered by the other electronic wave or you
connect the Bluetooth in the other rooms.
3
Operating
Connecting individual devices under Bluetooth
wireless technology does not incur any charges. A
mobile phone with Bluetooth wireless technology
can be operated via the Cascade if the connection
was made via Bluetooth wireless technology.
yy Available Devices : Smart phone, MP3, Notebook,
etc.
yy Version : 4.2
yy Codec : SBC
Bluetooth Profiles
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles.
This unit is compatible with following profile.
A2DP (Advanced Audio Distribution Profile)
Pairing your unit and Bluetooth device
1. Turn on the unit and select BT function by
pressing F.
“ ” on the display window blinks.
2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device display
depending on the type of Bluetooth device. Your
unit appears as “LG-LK72”.
,,Note
Depending on the Bluetooth device type, some
devices may have a different pairing process.
Enter the PIN code (0000) as needed.
Operating 17
3. When this unit is successfully connected with
your Bluetooth device, “ ” on the display
window turns on.
4. Listen to music.
To play a music stored on your Bluetooth device,
refer to your Bluetooth device’s user guide.
,,Note
yy When using Bluetooth technology, you have
to make a connection between the unit and
the Bluetooth device as close as possible and
keep the distance.
However, it may not work well in certain
situations as described below :
-- There is an obstacle between the unit and
the Bluetooth device.
yy If Bluetooth connection does not work well,
try pairing it again.
yy To connect a new Bluetooth device,
disconnect the currently connected
Bluetooth device and connect a new
Bluetooth device.
yy The sound may be interrupted when the
connection has interference from other
electronic devices.
yy Depending on the type of the device, you may
not be able to use the Bluetooth function.
yy You can enjoy wireless system using phone,
MP3, Notebook, etc.
yy The more distance between the unit and the
Bluetooth device, the lower the sound quality
becomes.
yy Bluetooth connection will be disconnected
when the unit is turned off or the Bluetooth
device gets far from the unit.
yy When Bluetooth connection is disconnected,
connect the Bluetooth device to the unit
again.
yy When a Bluetooth device is not connected,
“ ” on the display window blinks.
yy When you use the Bluetooth function,
adjust the volume to a proper level on the
Bluetooth device.
yy When entering Bluetooth function, this unit
automatically connect to Bluetooth device
which is connected the last or playbacked the
last. (Auto connection may not be supported
depending on the connected device
specifications.)
3
Operating
-- There is a device using same frequency
with Bluetooth technology such as a
medical equipment, a microwave or a
wireless LAN device.
,,Note
18 Operating
Radio Operations
Be sure to fully extend the FM wire antenna.
Listening to the radio
1.Press F until radio frequency appears in the
display window.
The last received station and “FM” appear on the
display window.
3
Operating
2. Auto tuning :
Press and hold TUNING +/- on the remote
control or C/V on the unit for about two
seconds until the frequency indication starts to
change, then release. Scanning stops when the
unit tunes in a station.
Or
Manual tuning :
Press TUNING+/- on the remote control or
C/V on the unit repeatedly.
3. Adjust the volume by pressing VOL +/-.
Presetting the Radio Stations
You can preset 50 stations for FM.
Before tuning, make sure to turn down the volume.
1.Press F until radio frequency appears in the
display window.
2. Select the desired frequency by pressing
TUNING +/- on the remote control or C/V
on the unit.
3.Press MEMORY on the remote control. A preset
number will blink in the display window.
4.Press PRESET W/S on the remote control to
select the preset number you want.
5.Press MEMORY on the remote control. The
station is stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen a preset station, press
PRESET W/S on the remote control.
Deleting all the saved stations
1.Press DELETE on the remote control.
“dEL”, “ALL” will flash up alternately on the unit
display.
2.Press DELETE on the remote control to erase all
the saved radio stations. “dELETEd ALL ” will be
displayed on the unit display.
Operating 19
Other Operations
Turn off the sound temporarily
Press [ on the remote control to mute your sound.
You can mute your unit, for example, to answer the
telephone, the “VOL” will blink on the display window.
To cancel it, press [ on the remo te control again or
change the volume level.
Auto power down
Adjusting Bass level
You can adjust the bass sound level as your
preference.
Adjust the bass sound level by pressing BASS +/-.
3
Operating
This unit will turn itself off to save electricity in the
case were the main unit is not connected to an
external device and is not used for 15 minutes.
The unit will also turn itself off after six hours if the
main unit has been connected to another device
using the analog inputs.
20 Troubleshooting
Troubleshooting
General
Problem
Cause & Solution
yy Turn off the power of this unit and the connected external device (Woofer,
DVD-player, Amplifier, etc.) and turn them on again.
The unit does not work
properly
yy Disconnect the power cord of this unit and the connected external device
(Woofer, DVD-player, Amplifier, etc.) and then try connecting again.
yy Previous setting may not be saved when device power is shut off.
No Power
4
No sound
yy The power cord is not plugged in. Plug in the power cord.
yy Check whether electricity failed.
Check the condition by operating other electronic devices.
yy Check whether you select right function.
Press function button and check the selected function.
Troubleshooting
yy Check to see if the Speakers are connected correctly. Speaker cables connected
correctly.
yy The signal strength of the radio station is too weak.
Tune to the station manually.
Radio stations cannot be
yy No stations have been preset or preset stations have been cleared (when tuning
tuned in properly
by scanning preset channels).
Preset some radio stations, see page 18 for details.
yy The remote control is too far from the unit.
Operate the remote control within about 7 m (23 feet).
The remote control does yy There is an obstacle in the path of the remote control and the unit.
Remove the obstacle.
not work properly
yy The batteries in the remote control are exhausted.
Replace the batteries with new ones.
Appendix 21
General specifications
General
Power requirements
Refer to the main label on the unit.
Power consumption
Refer to the main label on the unit.
Dimensions (W x H x D)
Approx. 196.0 mm x 239.0 mm x 205.0 mm
Operating temperature
5 °C to 35 °C
Operating humidity
60 %
Inputs
Analog audio in (AUX IN)
0.6 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
Portable in (PORT. IN)
0.4 Vrms (3.5 mm stereo jack) x 1
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
System
40 to 20,000 Hz
Signal-to-noise ratio
More than 75 dB
Dynamic range
More than 80 dB
Bus Power Supply (USB)
5 V 0 500 mA
Amplifier (RMS Output power)
Total output
40 W RMS
Front
10 W RMS X 2 (8 Ω at 1 kHz, 10 % THD)
Sub Woofer
20 W RMS X 1 (4 Ω at 1 kHz, 10 % THD)
Front speaker
Type
1 Way 1 spaker
Impadance
8Ω
Rated Input Power
10 W RMS
Max. Input Power
20 W RMS
Dimensions (W x H x D)
Approx. 109.0 mm x 140.0 mm x 100.0 mm
yy Design and specifications are subject to change without notice.
5
Appendix
Frequency Response
22 Appendix
Trademarks and
Licenses
Maintenance
Handling the Unit
The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth SIG, Inc. and
any use of such marks by LG Electronics is under
license.
Other trademarks and trade names are those of their
respective owners.
When shipping the unit
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally
packed at the factory.
Keeping the exterior surfaces clean
Do not use volatile liquids such as insecticide spray
near the unit. Wiping with strong pressure may
damage the surface. Do not leave rubber or plastic
products in contact with the unit for a long period of
time.
Cleaning the unit
5
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not use
strong solvents such as alcohol, benzine, or thinner,
as these might damage the surface of the unit.
Appendix
Download PDF

advertising