LG | NB2030A | LG NB2030A Owner’s Manual

ENGLISH
OWNER’S MANUAL
Sound Bar
Please read this manual carefully before operating your set and retain it
for future reference.
NB2030A
NB2030A-NO_DINDLLK_ENG.indd 1
2013-03-18
2:16:03
1
2
Getting Started
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with
arrowhead symbol within an
equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, should be placed on the
apparatus.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
NB2030A-NO_DINDLLK_ENG.indd 2
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. hen installing the product, ensure
that the plug is easily accessible.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
2013-03-18
2:16:04
Table of Contents
3
Table of Contents
1
Getting Started
2
Safety Information
4Accessories
4Introduction
4
– Symbols Used in this Manual
5
Remote control
6
Top panel
6
Rear panel
7
Installing the sound bar
7
Installing the cover foot
8
Mounting the main unit on a wall
2Connecting
9
9
Optional Equipment Connection
– OPTICAL In connection
1
3Operating
10Operations
10 – DRC (Dynamic Range Control)
10 – AV Sync
10 – AUTO POWER DOWN
10 – AUTO POWER On/Off
10 – Turn off the sound temporarily
11 – LG Sound Sync
12 Controlling a TV with the Supplied
Remote Control
3
4Troubleshooting
13Troubleshooting
4
5Appendix
14 Trademarks and Licenses
14Maintenance
14 – Handling the Unit
15Specifications
NB2030A-NO_DINDLLK_ENG.indd 3
2
5
2013-03-18
2:16:04
4
Getting Started
Accessories
Introduction
Please check and identify the supplied accessories.
Symbols Used in this Manual
1
Getting Started
,,Note
Indicates special notes and operating features.
>>Caution
Remote control (1)
Batteries (1)
Wall Mount Bracket
Installation Template
(1)
Wall mount bracket (2)
Optical cable (1)
Cover foot (2)
Indicates cautions for preventing possible damages
from abuse.
Cable ties for arranging
cables(2)
NB2030A-NO_DINDLLK_ENG.indd 4
2013-03-18
2:16:06
Getting Started
Remote control
5
• • • • • • • • • • a • • • • • • • • • •
1 (Power): Switches the unit ON or OFF.
DRC (ON/ OFF) : Sets the DRC.
• • • • • • • • • • b • • • • • • • • • •
VOL -/+ : Adjusts speaker volume.
AV SYNC -/+ : Synchronizes the audio and video.
,,Note
1
Getting Started
: Mutes the sound.
yy When the volume reaches the highest/
lowest level and you push VOL+/- on the
remote control again, red LED on the unit
turns on for 2 seconds to signal on what the
volume level is.
yy When the unit turns on, volume of the unit
will rise gradually to the volume level set at
the unit turned off.
• • • • • • • • • • c • • • • • • • • • •
TV Control buttons: See page 12.
Battery Installation
AUTO POWER (ON/OFF) : This function
automatically powers the unit ON/OFF.
Remove the battery cover on the rear of the
Remote Control, and insert battery with and
matched correctly.
NB2030A-NO_DINDLLK_ENG.indd 5
2013-03-18
2:16:07
6
Getting Started
Top panel
1
Getting Started
A 1 (Standby/On)
B – / + (Volume)
Adjusts speaker volume.
Rear panel
A Software Download Connector - Only for
service.
NB2030A-NO_DINDLLK_ENG.indd 6
B OPTICAL IN (TV)
2013-03-18
2:16:08
Getting Started
Installing the sound
bar
Installing the cover
foot
You can hear the sound by using optical cable
connect the unit to the other device : TV, Blu-ray
disc player, DVD player, etc.
You can extend the height of the unit.
7
1
Getting Started
Place the unit in front of the TV and connect it to
the device. (Refer to page 9.)
1. Turn the unit upside down.
2. Peel off a sticker attached to the cover foot.
Then place it on the existing foot of the unit.
3. Press the cover foot with adequate force to get
it firmly fixed.
NB2030A-NO_DINDLLK_ENG.indd 7
2013-03-18
2:16:08
8
Getting Started
Mounting the main
unit on a wall
1
Getting Started
You can mount the main unit on a wall.
Prepare screws and brackets.
2. When you mount it on a wall (concrete), use the
wall plugs (Not supplied). You should drill holes.
A guide sheet (Wall Mount Bracket Installation
Template) is supplied to drill. Use the sheet to
check the point to drill.
Unit
Wall Mount Bracket
Installation Template
Wall mount bracket
1. Match the TV’s BOTTOM EDGE of Wall Mount
Bracket Installation Template with the bottom
of TV and attach to the position.
,,Note
Screws and Wall Plugs are not supplied for
mounting the unit. We recommend the Hilti
(HUD-1 6 x 30) for the mounting.
TV
NB2030A-NO_DINDLLK_ENG.indd 8
2013-03-18
2:16:09
2Connecting
Connecting
3. Remove the Wall Mount Bracket Installation
Template.
9
,,Note
Detach the unit from the bracket as shown
below.
4. Fix the brackets with screws (not supplied) as
shown in the illustration below.
2
Connecting
Optional Equipment
Connection
OPTICAL In connection
5. Hang the main unit onto the bracket as shown
below.
Connect an optical output of external devices to
the OPTICAL IN connector.
To the digital
optical output
jack of external
device
>>Caution
yy Do not hang onto the installed unit and
avoid any impact to the unit.
yy Secure the unit firmly to the wall so that it
does not fall off. If the unit falls off, it may
result in an injury or damage to the product.
yy When the unit is installed on a wall, please
make sure that a child does not pull any of
connecting cables, as it may cause it to fall.
yy Do not install this unit upside down. It can
damage the parts of this unit or be the
cause of personal injury.
NB2030A-NO_DINDLLK_ENG.indd 9
2013-03-18
2:16:11
10
Operating
Operations
DRC (Dynamic Range Control)
Makes the sound clear when the volume is turned
down (Dolby Digital only). Set to DRC by pressing
DRC ON.
To cancel DRC, press DRC OFF.
AV Sync
3
When receiving audio signals from TV, sound and
images may not match. In that case, this function
can adjust the delay time.
Operating
Use AV SYNC -/+ to scroll up and down through
the delay amount, which you can set between
0 and 300 ms.
,,Note
When the AV SYNC reaches the highest/lowest
level and you push AV SYNC -/+ on remote
control again, red LED on the unit turns on for
2 seconds to signal what the AV SYNC level is.
AUTO POWER DOWN
This unit turns off automatically to save power
consumption if no signal is transmitted to the unit
for about 25 minutes.
AUTO POWER On/Off
This function automatically turns on the unit when
you turn on the external device (TV, DVD player,
Blu-ray player etc.) connected to the unit by optical
cable. Turn on this function by pressing AUTO
POWER ON.
To cancel it, press AUTO POWER OFF.
,,Note
If you don’t connect external device to the unit
by optical cable or there is no digital input, the
unit is turned off after 1 minutes when you
turn on this function.
It is not available to turn on the unit by AUTO
POWER function if you turn off it directly.
Turn off the sound temporarily
Press
to mute your unit.
You can mute your unit, for example, to answer the
telephone.
To cancel it, press MUTE
again on the remote
control or change the volume level.
,,Note
Red LED on the unit blinks at intervals of 2
seconds to signal that the unit is in mute
mode.
But the unit can turn on automatically based on the
[AUTO POWER] function you've set.
NB2030A-NO_DINDLLK_ENG.indd 10
2013-03-18
2:16:11
Operating
LG Sound Sync
11
With wired connection
1. Connect your LG TV to the unit by using an
optical digital cable.
You can control some functions of this unit by
your TV's remote control with LG Sound Sync. It
is compatible with the LG TV that is supported LG
Sound Sync. Make sure of the LG Sound Sync logo
on your TV.
Optical digital cable
Controllable function by LG TV's remote control :
Volume up/down, mute.
Refer to the TV's instruction manual for the details
of LG Sound Sync.
3
Operating
Make one of the following connections, depending
on the capabilities of your equipment.
,,Note
You can also use the remote control of this
unit while using LG Sound Sync. If you use TV's
remote control again, the unit synchronizes
with the TV.
When the connections failed, make sure of the
condition of the TV and power of it.
Make sure of the condition of this unit and the
connection in the cases below when using LG
Sound Sync.
2. Set up LG Sound Sync (Optical) on the TV. Refer
to the TV's instruction manual.
3. Turn on the unit.
4.Select OPTICAL function.
When you finish the connection, show a
message on your TV.
Turned off the unit.
Disconnecting the optical digital audio cable.
NB2030A-NO_DINDLLK_ENG.indd 11
2013-03-18
2:16:11
12
Operating
Controlling a TV with
the Supplied Remote
Control
You can control your TV using the buttons below.
(LG TV only.)
3
Operating
Button
Operation
MUTE
Turn the TV’s volume on or
off
INPUT
Switch the TV’s input source
between the TV and other
input sources.
1 (TV POWER)
Turn the TV on or off.
VOL +/–
Adjust the volume of the
TV.
PR/CH w/s
Scan up or down through
memorized channels.
,,Note
yy Depending on the TV being connected, you
may not be able to control your TV using
some of the buttons.
yy The remote control of the unit performs
basic operation of your TV. Please use the
TV’s remote control to enjoy advanced
operation of your TV.
NB2030A-NO_DINDLLK_ENG.indd 12
2013-03-18
2:16:12
Troubleshooting
13
Troubleshooting
PROBLEM
CORRECTION
Plug in the power cord.
No Power
No sound
Check the condition by operating other electronic devices.
Check the OPTICAL IN connection.
The remote control is too far from the unit.
The remote
control does
not work
properly.
Operate the remote control within about 23 ft (7m).
There is an obstacle in the path of the remote control and the unit.
Remove the obstacle.
The battery in the remote control is exhausted.
Replace the batteries with new one.
The AUTO
POWER
function does
not work.
Depending on the connected device by the optical cable, this function may not operate.
4
When you
sense that
outputted
sound of the
unit is low.
yy Switch [ON] state of DRC function to [OFF] by using remote controller.
yy With the sound bar connected with TV, change the AUDIO DIGITAL OUT setting on TV
Setup Menu from [PCM] to [AUTO] or [BITSTREAM].
yy With the sound bar connected with Player, change the AUDIO DIGITAL OUT setting on
Player Setup Menu from [PCM] to [PRIMARY PASS-THROUGH] or [BITSTREAM].
Troubleshooting
Check the details below and adjust the unit according to them.
yy Change Audio DRC setting on Player setup menu to [OFF] state.
NB2030A-NO_DINDLLK_ENG.indd 13
2013-03-18
2:16:12
14
Appendix
Trademarks and
Licenses
Maintenance
Handling the Unit
When shipping the unit
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS,
the Symbol, & DTS and the Symbol together are
registered trademarks & DTS 2.0 Channel is a
trademark of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.
5
Appendix
This product is manufactured under licence
from Sontia Logic Limited and contains software
which is protected under international copyright
laws ©Sontia Logic Limited. All rights reserved.
Sontia® and the Sontia wave logo are registered
trademarks of Sontia Logic Limited.
NB2030A-NO_DINDLLK_ENG.indd 14
yy Do not use volatile liquids such as insecticide
spray near the unit.
yy Wiping with strong pressure may damage the
surface.
yy Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
2013-03-18
2:16:13
Appendix
15
Specifications
General
Power requirements
Refer to the main label.
Power consumption
Refer to the main label.
Dimensions (W x H x D)
899.2 mm x 58.4 mm x 83.8 mm
(35.4 inches x 2.3 inches x 3.3 inches)
Net Weight (Approx.)
2.6 kg (5.7 lbs)
Operating temperature
41 °F to 95 °F (5 °C to 35 °C)
Operating humidity
5 % to 90 %
Inputs
DIGITAL IN (OPTICAL IN)
3 V (p-p), Optical jack x 1
Amplifier
Stereo mode
20 W + 20 W (6 Ω at 1 kHz)
Designs and specifications are subject to change without prior notice.
5
Appendix
NB2030A-NO_DINDLLK_ENG.indd 15
2013-03-18
2:16:13
NB2030A-NO_DINDLLK_ENG.indd 16
2013-03-18
2:16:13
Download PDF