LG | NB3520A | LG NB3520A Owner’s Manual

OWNER’S MANUAL
300 W Sound Bar System
Please read this manual carefully before operating
your set and retain it for future reference.
NB3520A (NB3520A, SHS36-D)
1
Getting Started
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with
arrowhead symbol within an
equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. hen installing the product, ensure
that the plug is easily accessible.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Getting Started
RF Radiation Exposure Statement
This equipment should be installed and operated
with minimum distance 20 cm between the
radiator and your body.
1. D.L.gs 1.8.2003, n. 259, article 104 (activity
subject to general authorization) for outdoor
use and article 105 (free use) for indoor use, in
both cases for private use.
2. D.M. 28.5.03, for supply to public of RLAN access
to networks and telecom services.
L’uso degli apparati è regolamentato da:
1. D.L.gs 1.8.2003, n. 259, articoli 104 (attività
soggette ad autorizzazione generale) se utilizzati
al di fuori del proprio fondo e 105 (libero uso) se
utilizzati entro il proprio
fondo, in entrambi i casi per uso private.
2. D.M. 28.5.03, per la fornitura al pubblico
dell’accesso R-LAN alle reti e ai servizi di
telecomunicazioni.
Brazil Notice
Este equipamento opera em caráter secundário, isto
é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e
não pode causar interferência a sistemas operando
em caráter primário.
1
Getting Started
Italy Notice
A general authorization is requested for outdoor
use in Italy.
The use of these equipments is regulated by:
3
4
Table of Contents
Table of Contents
1
Getting Started
2
Safety Information
6
Unique Features
6
– Portable In
6
– Speaker ez (easy) Setup
6Accessories
7Introduction
7
– Symbols Used in this Manual
7
Playable file
7
– MP3/ WMA file requirement
8
Remote control
9
Front panel
9
Rear panel
2Connecting
10
12
12
13
13
13
13
13
14
Mounting the main unit on a wall
Setting up
– Pairing wireless subwoofer
Optional Equipment Connection
– PORT. (Portable) IN Connection
– Listening to music from your portable
player
– OPTICAL In connection
– Speaker ez (easy) setup
– USB Playback
3Operating
15
15
15
15
15
15
16
16
16
16
16
16
17
17
17
18
18
20
20
Basic Operations
– USB Operation
Other Operations
– DOLBY DRC (Dynamic Range
Control)
– AV Sync
– AUTO POWER On/Off
– Sleep Timer Setting
– Dimmer
– Turn off the sound temporarily
– Adjust the woofer level settings
– Displaying file and input source
– Auto Power Down
Sound adjustment
– Setting the surround mode
– 3D Sound Effect
Using Bluetooth technology
– Listening to music stored on the
Bluetooth devices
Controlling a TV with the Supplied
Remote Control
– Setting up the remote to control your
TV
Table of Contents
5
4Troubleshooting
21Troubleshooting
5Appendix
22Maintenance
22 – Handling the Unit
23 Trademarks and Licenses
24Specifications
1
2
3
4
5
6
Getting Started
Unique Features
1
Portable In
Accessories
Please check and identify the supplied accessories.
Getting Started
Listen to music from your portable device. (MP3,
Notebook, etc)
AV/INPUT
Speaker ez (easy) Setup
Listen to sounds from TV, DVD or Digital device
with vivid 2.1 or 2.0 ch mode.
VOL +
PR/CH
VOL -
PR/CH
Remote control (1)
Batteries (2)
Wall Mount Bracket
Installation Template
(1)
Wall bracket (1)
Optical cable (1)
Getting Started
Introduction
Playable file
Symbols Used in this Manual
MP3/ WMA file requirement
Indicates special notes and operating features.
,,Tip
Indicates tip and hints for making the task easier.
>>Caution
Indicates cautions for preventing possible damages
from abuse.
MP3/ WMA file compatibility with this unit is limited
as follows :
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
yy Maximum files : Under 999
yy File extensions : “.mp3”/ “.wma”
1
Getting Started
,,Note
7
8
Getting Started
Remote control
• • • • • • • • • • a • • • • • • • • • •
1 (Power): Switches the unit ON or OFF.
INPUT: Changes input sources.
W/S FOLDER: Searches for a folder of MP3/
WMA files. When an USB containing MP3/ WMA
files in several folders is being played,
press W/S FOLDER to select the folder you want
to play.
1
Getting Started
OPTICAL: Changes input source to optical directly.
MUTE
: Mutes the sound.
-/+ VOL: Adjusts speaker volume.
• • • • • • • • • • b • • • • • • • • • •
AUTO POWER: This function is automatically
turned on the unit.
AV SYNC: Synchronizes the audio and video.
INFO: Displays the file or input source information.
REPEAT: Listens to your files repeatedly or
randomly.
C/V (Skip/ Search) :
- Skips Fast backward or Forward.
- Searches for a section within a track.
Z: Stops playback.
d/M: Starts playback. / Pauses playback.
AV/INPUT
VOL +
PR/CH
SOUND EFFECT: Selects a sound effect mode.
VOL -
PR/CH
3D SOUND: Turns on and off the 3D Sound mode.
WOOFER LEVEL: Sets the sound level of woofer.
• • • • • • • • • • c • • • • • • • • • •
0 to 9 numerical buttons: Selects numbered files.
Enters the PIN code.
DOLBY DRC: Sets the Dobly DRC.
Battery Installation
Remove the battery cover on the rear of the
Remote Control, and insert two (size AAA) battery
with and matched correctly.
SLEEP: Sets the system to turn off automatically at
a specified time.
• • • • • • • • • • d • • • • • • • • • •
TV Control buttons: See page 20.
Getting Started
9
Front panel
B
A
1
F
E
D
C
>>Caution
ADisplay
B USB Port
Precautions in using the touch buttons
CF (Function)
Press it repeatedly to select other function.
yy Use the touch buttons with clean and dry
hands.
- In a humid environment, wipe out any
moisture on the touch buttons before
using.
D I (Stop)
E T (Play / Pause)
F – / + (Volume)
Adjusts speaker volume.
yy Do not press the touch buttons hard to
make it work.
- If you apply too much strength, it can
damage the sensor of the touch buttons.
G 1 (Standby/On)
yy Touch the button that you want to work in
order to operate the function correctly.
yy Be careful not to have any conductive
material such as metallic object on the
touch buttons. It can cause malfunctions.
Rear panel
A
B
A PORT. (Portable) IN
B OPTICAL IN 1/ 2
Getting Started
G
10
Connecting
Mounting the main
unit on a wall
You can mount the main unit on a wall.
Prepare screws and brackets.
2. When you mount it on a wall (concrete), use
the wall plugs (Not supplied). You should drill
some holes. A guide sheet (Wall Mount Bracket
Installation Template) is supplied to drill. Use the
sheet to check the point to drill.
Wall Mount Brac
ket Installation
Template
Unit
2
Connecting
Wall Mount Bracket
Installation Template
Wall bracket
,,Note
1. Match the TV’s BOTTOM EDGE of Wall Mount
Bracket Installation Template with the bottom
of TV and attach to the position.
TV
Screws and Wall Plugs are not supplied for
mounting the unit. We recommend the Hilti
(HUD-1 6 x 30) for the mounting. Please
purchase it.
Connecting
3. Remove the Wall Mount Bracket Installation
Template.
11
5. Hang the main unit onto the bracket as shown
below.
4. Fix it with screws (not supplied) as shown in the
illustration below.
2
Connecting
>>Caution
yy Do not hang onto the installed unit and
avoid any impact to the unit.
yy Secure the unit firmly to the wall so that it
does not fall off. If the unit falls off, it may
result in an injury or damage to the product.
yy When the unit is installed on a wall, please
make sure that a child does not pull any of
connecting cables, as it may cause it to fall.
,,Note
Detach the unit from the bracket as shown
below.
12
Connecting
Setting up
Pairing wireless subwoofer
When your connection is not completed, you can
see the red LED on the woofer and woofer is not
made sound. To solve the problem, follow the
below steps.
LED Color
Status
1. Press and hold I STOP button on the unit
and MUTE button on the remote control
simultaneously.
- Displays the “REMATE”.
Blue or yellow
The wireless subwoofer is
receiving the signal of the unit.
2.Press PAIRING on back of the woofer.
- The blue or yellow LED will flicker
Blue or yellow
(blink)
The wireless subwoofer is trying
to connect.
Red
The Wireless subwoofer is in
standby mode.
Off (No
display)
The power cord of wireless
subwoofer is disconnected.
LED indicator of wireless subwoofer
2
Manually pairing wireless subwoofer
Connecting
3. Turn off and on the unit.
- If you see “blue or yellow” LED, it’ s successful.
4. If you don’t see “blue or yellow” LED, try again
Step 1 - Step 3.
,,Note
yy If you operate main unit then wireless
subwoofer sound within a few seconds in
standby mode.
Setting up the wireless subwoofer
for the first time
yy Set the distance between this unit and
wireless subwoofer within 10 m (32 ft.).
1. Connect the power cord of the Wireless
subwoofer to the outlet.
yy Optimum performance can be
implemented only when the unit and
the Wireless subwoofer within distance
of 2 m (6 ft.) to 10 m (32 ft.) is used since
communication failure may occur if longer
distance is used.
2. Turn on the main unit : The main unit and
wireless subwoofer will be automatically
connected.
yy It takes a few seconds (and may take longer)
for the unit and subwoofer to communicate
with each other.
Connecting
Optional Equipment
Connection
13
OPTICAL In connection
Connect an optical output of external devices to
the OPTICAL IN 1/ 2 connector.
PORT. (Portable) IN
Connection
MP3 player, etc...
2
Connecting
To the digital
optical output jack
of external device
Listening to music from your
portable player
The unit can be used to play the music from many
types of portable player or external devices.
1. Connect the portable player to the
PORT. (Portable) IN connector of the unit.
2. Turn the power on by pressing 1 (Power).
3. Select the PORTABLE function by pressing
INPUT.
4. Turn on the portable player or external device
and start playing it.
Speaker ez (easy) setup
Listens to sound from TV or DVD or Digital Device
with 2.1 or 2ch mode.
1. Connect the unit’s OPTICAL IN 1/ 2 jack to jack
on optical out of your TV (or Digital Device etc.).
2. Select the OPTICAL 1/ 2 by using the OPTICAL.
To select the OPTICAL 1/ 2 directly
3. Listen to sound with 2.1 or 2ch speaker.
4.Press OPTICAL to exit from OPTICAL 1/ 2.
Function is retuned to previous one.
14
Connecting
USB Playback
Compatible USB Devices
Insert USB memory device to the USB port on the
right side of the unit.
yy MP3 Player : Flash type MP3 player.
yy USB Flash Drive :Devices that support USB1.1.
yy The USB function of this unit does not support
some USB devices.
USB device requirement
yy Devices which require additional program
installation connected to a computer, are not
supported.
2
Connecting
yy Do not extract the USB device while in operation.
yy For a large capacity USB, it may take longer than
a few minutes to be searched.
Removing the USB Device from the unit.
1. Choose a different function mode or press
I STOP twice in a row.
2. Remove the USB device from the unit.
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
yy This unit is not supported when the total
number of files is 1000 or more.
yy External HDD, Card readers, Locked devices, or hard type USB devices are not supported.
yy The unit’s USB Port cannot be connected to PC.
The unit can not be used as a storage device.
Operating
15
Basic Operations
Other Operations
USB Operation
DOLBY DRC (Dynamic Range
Control)
1. Connect the USB device to the USB port.
2. Select the USB function by pressing INPUT.
3. Select a file you want to play by pressing
C or V.
To
Stop
Do this
Press Z.
Playback
Press d/M.
Pause
Press d/M.
AV Sync
When receiving audio signals from TV, sound and
images may not be matched. In the case, this
function can adjust the delay time.
1.Press AV SYNC.
During playback, press C
or V to go to the next file
or to return to the beginning
of the current file.
2.Use C V to scroll up and down through
the delay amount, which you can set at
anything between 0 and 300ms.
Press C twice briefly to
step back to the previous file.
AUTO POWER On/Off
Searching for a
section within a
file
Press and hold C/V
during playback and release it
at the point you want to listen
to.
Playing
repeatedly or
randomly
Press REPEAT on the remote
control repeatedly, the display
change in the following order,
RPT 1 RPT D (DIRECTORY)
RPT ALL RANDOM OFF.
Selecting files
directly
Press 0 to 9 numerical
buttons on the remote
control to go to the desired
file directly.
Before operating this function, make sure that you
have selected OPTICAL IN and turn on the AUTO
POWER. This function automatically turns on/off
the unit when you turn on/off the external device
(TV, DVD Player, Blu-ray Disc Player, etc.) connected
to this unit by the optical cable. This function turns
on or off each time you press AUTO POWER.
Display
Operation
AUTO POWER ON
AUTO POWER function is
turned on.
AUTO POWER OFF
AUTO POWER function is
turned off.
,,Note
yy This function is intentionally designed
to turn off the unit after 15 minutes of
inactivity. If you did not connect external
devices with optical cable or there is no
digital audio signal going to the unit,
the unit will turn off after 15 minutes of
inactivity if AUTO POWER function is turned
on.
yy Depending on the connected device by the
optical cable, this function may not operate.
3
Operating
Skipping to the
next/ previous
file
Make the sound clear when the volume is turned
down (Dolby Digital only). Set to [DRC ON] by using
DOLBY DRC.
16
Operating
Sleep Timer Setting
Press SLEEP one or more times to select delay time
between 10 and 180 minutes, after the unit will
turn off.
To check the remaining time, press SLEEP.
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.
,,Note
You can check the remaining time before the
Unit turns off.
3
Press SLEEP. The remaining time appears in
the display window.
You can display various information on the USB and
OPTICAL IN 1/ 2 mode by pressing INFO.
USB : MP3/ WMA containing file information
OPTICAL IN 1/ 2 : Audio format, Audio channel
Auto Power Down
This unit will be off itself to save electronic
consumption in the case main unit is not
connected to external device and is not used for 25
minutes.
Operating
So does this unit after six hours since Main unit
has been connected to other device using analog
input.
Dimmer
Press SLEEP once. The display window will be
darken by half. To cancel it, press SLEEP repeatedly
until dim off.
Turn off the sound temporarily
Press MUTE
Displaying file and input
source
to mute your unit.
You can mute your unit, for example, to answer
the telephone, the “ ” is displayed in the display
window.
Adjust the woofer level
settings
You can adjust the sound level of woofer.
1.Press WOOFER LEVEL.
2.Press -/+ VOL to adjust the sound level of the
woofer.
But the unit can turns on automatically based on
the [AUTO POWER] function you’ve set.
Operating
Sound adjustment
17
,,Note
Setting the surround mode
yy In some of surround modes, some speakers,
there’s no sound or low sound. It depends
on the mode of surround and the source of
audio, it is not defective.
This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using SOUND EFFECT.
yy You may need to reset the surround mode,
after switching the input, sometimes even
after the sound file changed.
The displayed items for the equalizer may be
different depending on sound sources and effects.
On Display
NATURAL
You can enjoy comfortable
and natural sound.
You can enjoy the sound
without equalizer effect.
BASS
The BASS is Bass Blast. During
playback, reinforce the treble,
bass and surround sound
effect.
CLRVOICE
The CLRVOICE is Clear Voice.
This program make voice
sound clear, improving the
quality of voice sound. (We
encourage to use this EQ
when you watch the movie of
5.1 channel.)
GAME
The GAME is Game Equalizer.
You can enjoy more virtual
sound while playing video
games.
NIGHT
The NIGHT is Night Mode.
This may be useful when you
want to watch movies at low
volume late at night.
UPSCALER
The UPSCALER is MP3 UpScaling. When listening to
MP3 files or other compressed
music, you can enhance the
sound. This mode is available
only to 2 channel sources.
LOUDNESS
Improves the bass and treble
sound.
3D Sound Effect
3D Sound features deliver sound creating a
wider spot so you can enjoy more immersive and
cinematic surround sound. Press 3D SOUND to
turn on or off the 3D Sound mode.
3
Operating
BYPASS
Description
18
Operating
Using Bluetooth
technology
About Bluetooth
Bluetooth® is wireless communication technology
for short range connection.
The available range is within 10 meters.
3
Operating
(The sound may be interrupted when the
connection interfered by the other electronic wave
or you connect the bluetooth in the other rooms.)
Connecting individual devices under
Bluetooth® wireless technology does not incur any
charges. A mobile phone with
Bluetooth® wireless technology can be operated
via the Cascade if the connection was made via
Bluetooth® wireless technology.
Available Devices : Mobile phone, MP3, Laptop,
PDA (This units be supported the Stereo Headset.)
Bluetooth Profiles
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles.
This unit is compatible with following profile.
A2DP (Advanced Audio Distribution Profile)
Listening to music stored on
the Bluetooth devices
Pairing your unit and Bluetooth
device
Before you start the pairing procedure, make
sure the Bluetooth feature is turned on in to your
Bluetooth device. Refer to your Bluetooth device’s
user guide. Once a pairing operation is performed,
it does not need to be performed again.
1. Select the Bluetooth function by using the
INPUT.
Appears “BT” and then “BT READY” in display
window.
2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device
display depending on the type of Bluetooth
device.Your unit appears as “LG Audio”.
3. Enter the PIN code.
PIN code : 0000
4. When this unit successfully paired with your
Bluetooth device, Bluetooth LED of this unit
lights up and appears “PAIRED”.
,,Note
Depending on the Bluetooth device type,
some device have a different pairing way.
5. Listen to music.
To play a music stored on your Bluetooth device,
refer to your Bluetooth device’s user guide.
,,Note
If you change the function of the unit, the
Bluetooth function is disconnected, operate
pairing again.
Function other than the
(Bluetooth
Bluetooth)
Operating
19
,,Note
yy The sound may be interrupted when
the connection interfered by the other
electronic wave.
yy You cannot control the Bluetooth device
with this unit.
yy Pairing is limited one Bluetooth device per
one unit and multi-pairing is not supported.
yy Although the distance between your
Bluetooth and the set is less than 10m, there
are obstacles between both, your Bluetooth
device cannot be connected.
yy Depending on the type of the device,
you may not be able to use the Bluetooth
function.
yy When not connected the Bluetooth, “BT
READY” appears on the display window.
yy The Electrical malfunction due to devices
using same frequency such as Medical
equipment, Microwaves or wireless
LAN devices, the connection will be
disconnected.
yy When someone stands and interrupts
communication between Bluetooth device
and the player, the connection will be
disconnected.
yy If the gotten away of the distance between
Bluetooth and the unit, the sound quality
is lower and lower the connection will
disconnect when the space between the
Bluetooth and the unit gets out of the
operating range of Bluetooth.
yy The device with Bluetooth wireless
technology is disconnected, if you turn off
the main unit or put the device away from
the main unit more than 10m.
3
Operating
yy You can enjoy wireless system using phone,
MP3, Notebook, etc..
20 Operating
Controlling a TV with
the Supplied Remote
Control
You can control your TV using the buttons below.
AV/INPUT
VOL +
PR/CH
VOL -
PR/CH
3
Setting up the remote to
control your TV
You can operate your TV with the supplied remote
control.
If your TV is listed in the table below, set the
appropriate manufacturer code.
1. While holding down 1 (TV POWER) button,
and press the manufacturer code for your
TV with the numerical buttons (see the table
below).
Manufacturer
Code Number
LG
1(Default), 2
Zenith
1, 3, 4
Operating
Button
Operation
GoldStar
1, 2
MUTE
Turn the TV’s volume on or
off
Samsung
6, 7
Sony
8, 9
AV/INPUT
Switch the TV’s input source
between the TV and other
input sources.
Hitachi
4
1 (TV POWER)
Turn the TV on or off.
VOL +/–
Adjust the volume of the
TV.
PR/CH W/S
Scan up or down through
memorized channels.
,,Note
Depending on the unit being connected, you
may not be able to control your TV using some
of the buttons.
2. Release the 1 (TV POWER) button to complete
setting.
Depending on your TV, some or all buttons may not
function on the TV, even after entering the correct
manufacturer code. When you replace the batteries
of the remote, the code number you have set may
be reset to the default setting. Set the appropriate
code number again.
Troubleshooting
21
Troubleshooting
PROBLEM
CORRECTION
Plug in the power cord.
No Power
Check the condition by operating other electronic devices.
Press INPUT and check the selected function.
No sound
The power cord of woofer is not connected. Plug the power cord into the wall outlet
securely.
Pairing between the unit and woofer gets disconnected. Connect the unit and woofer.
(Refer to the page 12)
The remote control is too far from the unit.
The remote
control does
not work
properly.
Operate the remote control within about 23 ft (7m).
There is an obstacle in the path of the remote control and the unit.
Remove the obstacle.
The battery in the remote control is exhausted.
Replace the batteries with new one.
Depending on the connected device by the optical cable, this function may not operate.
4
Troubleshooting
The AUTO
POWER
function does
not work.
22 Appendix
Maintenance
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
yy Do not use volatile liquids such as insecticide
spray near the unit.
yy Wiping with strong pressure may damage the
surface.
yy Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Cleaning the unit
5
Appendix
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Appendix 23
Trademarks and
Licenses
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS,
the Symbol, & DTS and the Symbol together are
registered trademarks & DTS 2.0 Channel is a
trademark of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.
Connecting individual devices under Bluetooth®
wireless technology does not incur any charges.
A mobile phone with Bluetooth® wireless technology can be operated via the Cascade if the
connection was made via Bluetooth® wireless
technology.
The Bluetooth® word mark and logos are owned
by the Bluetooth® SIG, Inc. and any use of such
marks by LG Electronics is under license.
Other trademarks and trade names are those of
their respective owners.
5
Appendix
Bluetooth® wireless technology is a system which
allows radio contact between electronic devices
within a max. range of 10 meters.
24 Appendix
Specifications
General
Power requirements
Refer to the main label.
Power consumption
Refer to the main label.
Dimensions (W x H x D)
1 000 x 80 x 55 mm without foot
Net Weight (Approx.)
3.0 kg
Operating temperature
41 °F to 95 °F (5 °C to 35 °C)
Operating humidity
5 % to 90 %
Bus Power Supply (USB)
DC 5 V 0 500 mA
Inputs
DIGITAL IN (OPTICAL IN)
3 V (p-p), Optical jack x 2
PORT. IN
0.5Vrms (3.5 mm stereo jack)
Amplifier
Stereo mode
80 W + 80 W (4 Ω at 1 kHz)
Subwoofer
140 W (3 Ω at 60 Hz)
5
Wireless subwoofer
Appendix
Power requirements
Refer to the main label.
Power consumption
Refer to the main label.
Type
1 Way 1 Speaker
Impedance Rated
3Ω
Input Power
140 W
Max. Input Power
280 W
Net Dimensions (W x H x D)
196 x 392 x 317 mm
Net Weight
6.88 kg
Designs and specifications are subject to change without prior notice.
Download PDF