LG | LCF610IR | LG LCF610IR Owner’s Manual

OWNER’S MANUAL
CAR CD/MP3/WMA
Receiver
Please read this manual carefully before operating
your set and retain it for future reference.
LCS510IR/LCS510UR/LCF610IR
P/NO : MFL67244328
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
To reduce the risk of electric
shock, do not remove the cover
or back of this product. There are
no user-serviceable parts inside.
Refer servicing to qualified service
personnel.
To reduce the risk of fire or electric
shock, do not expose this product
to dripping or splashing water, rain,
or moisture.
The temperature of unit’s outside
can be extremely high, please use
the unit after proper installation in
your vehicle.
This unit cannot play 8cm disc (use
12cm disc only).
While driving, keep the sound
volume at a proper level.
Do not drop it and avoid heavy
impacts at anytime.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
Always operate the vehicle in a safe
manner. Do not become distracted
by the vehicle while driving, and
always be fully aware of all driving
condition. Do not change settings,
or any functions. Pull over in a
safe and legal manner before
attempting such operations.
Do not use for many hours at
extremely low or high temperature.
(-10 °C to 60 °C)
This unit is for vehicles with a
12-volt battery and negative
grounding. Before installing it
in a recreational vehicle, lorry or
bus, check the battery voltage.
To avoid shorts in the electrical
system, be sure to disconnect the E
battery cable before beginning the
installation.
Getting Started
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by the
European Directive 2002/96/EC.
1
2. All electrical and electronic products
shall be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or the
local authorities.
Getting Started
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service centre.
3
3. The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
“This device is equipped with a portable battery or
accumulator.
Safe way to remove the battery or the battery
from the equipment:
Remove the old battery or battery pack, follow the
steps in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators.”
The battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot
use it on LG players.
(Mastered/Live File System : Disc format system for
Windows Vista)
> Caution
When being connected in a wrong way, the
unit displays as follows.
- Antenna port short : "EXTERNAL ON PORT
SHORT CIRCUIT CHECK"
After connecting it again, restart the unit.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you
purchased the product.
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and
other relevant provisions of Directive
2006/95/EC and ECE Regulation 10.03
(3.2.9).
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere, The
Netherlands
(Tel : +31-(0)36-547-8888)
The unit is compatible with the steering wheel
remote control. The function allows operation
by sending the steering wheel remote control
signal to the unit.
For details, consult with your dealer.
4
Table of Contents
Table of Contents
15
21
21
– Playing back tracks/ files in a way you
want
Listening to music from an external
device
– Preventing radical changes in volume
as switching sources
Listening to the radio
– Storing desired frequencies manually
– Listening to a preset station
– Adjusting TUNER settings
Using an USB device
– Moving to another drive
– Quick Search of a desired file
– Playable USB device Requirement
– Recording to USB from CD or FM
tuner
Listening to music by connecting iPod/
iPhone [LCS510IR/LCF610IR]
– Pausing or restarting playback
– Searching for a section within a track/
file
– Checking information about your
music
– Playing back tracks/ files in a way you
want
– Playing back files by music menus
– Compatible iPod models
4
Troubleshooting
22
Troubleshooting
5
Appendix
23
Specifications
16
1
2
3
4
5
1
Getting Started
2
5
6
7
7
Safety Information
Front panel [LCS510IR/ LCS510UR]
Front panel [LCF610IR]
Remote control
– Battery Installation
2
Connecting
8
About detachable control panel
[LCS510IR/LCS510UR]
– Attaching the control panel
– Detaching the control panel
About detachable control panel
[LCF610IR]
– Attaching the control panel
– Detaching the control panel
Installation
– Basic Installation
– Removing the existing receiver unit
– ISO-DIN Installation
Connection
– Connecting to a car
8
8
9
9
9
10
10
10
10
11
11
3
Operating
12
12
12
12
12
12
12
13
14
14
14
Operation
– Basic operations
– Turning off the sound temporarily
– Using EQ (Equalizer)
– Checking the clock
– Turning off the display light
– Resetting the unit
– Adjusting the general settings
Listening to a CD
– Pausing or restarting CD playback
– Searching for a section within a track/
file
– Skipping to another track/ file
– Checking information about your
music
15
15
16
17
17
17
18
19
19
19
19
19
20
20
20
20
20
Getting Started
5
Front panel [LCS510IR/ LCS510UR]
a b
c
d
e
f g
h
i
1
Getting Started
ͶͿ΅Ͷ΃͠
͑͑͑͑͑ͽͺ΄΅
j
k
l
m
n
o
p q r
s
t
a B
Ejects a disc.
j R
Recording to USB.
b SRC/ • OFF
• When pressed, selects function sources.
• When pressed and held, powers unit on or off.
k `
Activates setting menu.
c N
Plays and pauses playback.
Temporarily stops the sound.
d Volume knob
• Adjusts volume level.
• Confirms the settings.
• Checks tracks, files or preset stations.
e F
In each mode, sets playback items.
f BAND
Selects a band in Tuner mode.
• TA (Optional)
Searches stations that have TA/ TP information,
when it is pressed and held.
g Remote Sensor
h Display window
i 6
Opens the front panel.
u
l
Returns to the previous step.
m A/D
Skip/ Search/ Seek/ Tune
n EQ
Improves sound quality.
• When pressed, selects the EQ function.
• When pressed and held, adjusts the sound
level.
o DISP
• Press it, you can check the clock time.
• Press and hold it, you can turn on/off the
display window and the light of LED buttons.
p INT
Intro scan
q RPT
Repeats playback
r SHF
Randoms playback
s Numeric buttons (1 - 6)
Selects a numbered preset station in TUNER.
t AUX
If connected to other portable player, you can
enjoy musics from it on the unit.
u USB port
6
Getting Started
Front panel [LCF610IR]
a b
1
c
d
f
e
g h
Getting Started
ͶͿ΅Ͷ΃͠
͑͑͑͑͑ͽͺ΄΅
i
j k
l
m
n
a SRC/ • OFF
• When pressed, selects function sources.
• When pressed and held, powers unit on or off.
b N
Plays and pauses playback.
Temporarily stops the sound.
c Volume knob
• Adjusts volume level.
• Confirms the settings.
• Checks tracks, files or preset stations.
d F
In each mode, sets playback items.
e BAND
Selects a band in Tuner mode.
• TA (Optional)
Searches stations that have TA/ TP information,
when it is pressed and held.
f Display window
g Remote Sensor
h OPEN
Opens the front panel.
i R
Recording to USB.
o
p
j `
Activates setting menu.
k
Returns to the previous step.
l A/D
Skip/ Search/ Seek/ Tune
m EQ
Improves sound quality.
• When pressed, selects the EQ function.
• When pressed and held, adjusts the sound
level.
n DISP
• Press it, you can check the clock time.
• Press and hold it, you can turn on/off the
display window and the light of LED buttons.
o AUX
If connected to other portable player, you can
enjoy musics from it on the unit.
p USB port
Getting Started
Remote control
7
i DISP
• Press it, you can check the clock time.
• Press and hold it, you can turn on/off the
display window and the light of LED buttons.
1
k INT
Intro scan
l Numeric buttons (1 - 6)
Selects a numbered preset station in TUNER.
Battery Installation
a SRC/ • OFF
• When pressed, selects function sources.
• When pressed and held, powers unit off.
b FUNC
When pressed, sets playback items in each
mode.
• MENU
When pressed and held, activates setting
menu.
c BAND
Selects a band in Tuner mode.
DRV
Moves to a next USB drive.
d d/M Plays or pauses playback.
e SHF Randoms playback
f MUTE Temporarily stops the sound.
g VOLUME W/S
Adjusts volume level.
h c/v
Skip/ Search/ Seek/ Tune
Returns to the previous step.
w/s
• List up/ down
• Adjusts settings.
• Moves 10 MP3/WMA tracks backward or
forward if there is no folder or one folder on a
CD.
• Moves to the previous or next folder if there
are more than 2 folders on a CD.
ENTER/ LIST
• Confirms the settings.
• Checks tracks, files or preset stations.
1. Pull out the battery holder with a sharp product
like a ball point pen.
2. Put the battery with
battery holder.
and
correctly on the
3. Push the battery holder back into its original
position.
, Note
 Use only one CR2025 (3 V) lithium battery.
 Remove the battery if the remote control is
not used for a long period of time.
 Do not leave the product in a hot or humid
place.
 Do not handle the battery with metallic
tools.
 Do not store the battery with metallic
materials.
Getting Started
j RPT
Repeats playback
8
Connecting
About detachable
control panel
[LCS510IR/
LCS510UR]
2
Attaching the control panel
Detaching the control panel
1. Press the 6 to open the control panel.
2. Push the control panel to right.
Connecting
1. Align the left side of the panel with the stopper.
2. Push the right side of panel into the unit until it
clicks.
3. Pull the control panel out of the unit.
4. Put the detached control panel into the
protective case.
> Caution
 The control buttons may not work properly
if the control panel is not attached properly.
If this occurs, gently press the display.
 Do not leave the control panel in any area
exposed to high temperatures or direct
sunlight.
 Do not drop the control panel or otherwise
subject it to strong impact.
 Do not allow such volatile agents as
benzine, thinner, or insecticides to come
into contact with the surface of the control
panel.
Control panel
Protective Case
, Note
Periodically wipe the contacts on the back
of the control panel with a cotton swap
moistened with alcohol. For safety, turn off the
ignition before cleaning, and remove the key
from the ignition switch.
Connecting
About detachable
control panel
[LCF610IR]
9
Detaching the control panel
1. Press the OPEN to open the control panel.
Attaching the control panel
2. Push the control panel to left.
i
h
2. Attach part C of the control panel to part D
of the unit while pushing the control panel to
left.
3. Pull the control panel out of the unit.
4. Put the detached control panel into the
protective case.
3. Close the control panel.
k
j
Control panel
Protective Case
> Caution
 The control buttons may not work properly
if the control panel is not attached properly.
If this occurs, gently press the display.
 Do not leave the control panel in any area
exposed to high temperatures or direct
sunlight.
 Do not drop the control panel or otherwise
subject it to strong impact.
 Do not allow such volatile agents as
benzine, thinner, or insecticides to come
into contact with the surface of the control
panel.
2
Connecting
1. Attach part CA of the control panel to part CB
of the unit.
, Note
Periodically wipe the contacts on the back
of the control panel with a cotton swap
moistened with alcohol. For safety, turn off the
ignition before cleaning, and remove the key
from the ignition switch.
10
Connecting
Installation
ISO-DIN Installation
Basic Installation
Before installing, make sure that the ignition-switch
is set to OFF and remove the terminal of the car
battery to avoid short-circuiting.
2
Connecting
Bend the claws
according to
the thickness
of the
dashboard.
Control panel
1. Slide the unit into the ISO-DIN frame.
2. Fit screws removed from the old unit.
3. Slide the unit and frame into the dash opening.
4. Install the dash panel or adapter plate.
Control panel
1. Remove the existing receiver unit.
2. Make the necessary connections.
3. Install the installation sleeve.
4. Install the unit into the installation sleeve.
Removing the existing receiver
unit
If there is already an installation sleeve for the
receiver unit in the dashboard, it must be removed.
1. Remove the rear support from the unit.
2. Remove the control panel and trim ring from
the unit.
3. Insert the lever into the hole on one side of the
unit. Perform the same operation on the other
side and pull the unit out from the mounting
sleeve.
(According to models, this step may not be
needed.)
5. Install the trim ring to the unit.
6. Install the control panel to the unit.
Connecting
11
Connection
Connecting to a car
Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery
to avoid short-circuiting.
Wired remote input (Black): Hard-wired control adapter can be connected.
(Optional/ Not supplied)
Rear Left (Sub-woofer Left)
Front Left
Rear Right (Sub-woofer Right)
Front Right
Amplifier
ab c d ab c d
ef g h ef g h
Power
Antenna
Control Relay
B f Power Antenna (Blue)
B g Dimmer (Pink)
Dimmer Switch
B c To Ignition (Red)
Ignition Switch
a
b
A
c
A
d
A
e
A
f
A
g
A
h
B h Ground (-) (Black)
B e Remote On
(Blue/ White)
A
A
B d To Battery (+) (Yellow)
Amplifier
A a Gray: Front Right +
A b Gray/ Black Stripe: Front Right A c Violet: Rear Right +
B b Phone Mute
(Orange)
A d Violet/ Black Stripe: Rear Right A e White: Front Left +
A f White/ Black Stripe: Front Left -
B a Not connected
A g Green: Rear Left +
A h Green/ Black Stripe: Rear Left -
Connecting
To Audio in (Optional)
To Audio out (Optional)
2
12
Operating
Operation
Checking the clock
1. Press DISP to check the clock.
2. Press it again to remove it.
Basic operations
1. Turn the unit on by pressing any key on the
unit.
Turning off the display light
2. Select a source by pressing SRC.
2. Press and hold it again to turn it on.
3. Rotate the volume knob to adjust the volume
on the unit.
Or press VOLUME W/S on the remote control.
, Note
3
If a source is not connected to the unit, the
source is not recognized.
Operating
Turning off the sound
temporarily
1. Press
to mute your unit.
Or press MUTE on the remote control.
2. To cancel it, press again.
Or press MUTE again.
1. Press and hold DISP.
, Note
Under the light-off condition, press any
keys, the light is turned on and then off
automatically if you don't press it within a few
seconds.
Resetting the unit
You can reset the unit when it does not operate
properly.
1. Detach the control panel.
Refer to page 8-9 for detaching the control
panel.
2. Press the RESET hole with a sharp object.
Using EQ (Equalizer)
EQ is to increase or decrease the signal strength of
audio frequencies. The function helps you to enjoy
sound more plentifully.
Press EQ on the unit repeatedly. The indicator lights
up in the following order.
XDSS+ / POP / CLASSIC / ROCK / JAZZ /
VOCAL / SALSA / SAMBA / REGGAE / RUSSY
/ USER 1 / USER 2 / Off (not displayed)
, Note
You can adjust sound level to your preference.
Once you select a USER 1/2 mode and press
` on the unit, then adjust the sound level
(BASS (bass), MID (middle), TRB (treble), BAL
(left/right speaker), FAD (front/rear speaker),
S--W (Sub-woofer: optional)), it will be
automatically stored for the currently selected
USER 1/2 mode. Refer to the "For [SOUND]
setting" for USER 1/2 mode on the page 13.
[LCS510IR/ LCS510UR]
[LCF610IR]
Operating
Adjusting the general settings
For [LIGHT] setting
You can adjust [SOUND], [LIGHT] and [OTHER]
settings.
You can adjust the light effects by adjusting LED,
DIM, or DIM L.
On the unit
 LED COL1/ COL2/ AUTO: You can change the
LED window color.
1. Press `.
2. Rotate the volume knob to select [SOUND],
[LIGHT], or [OTHER] and press it.
 DIM (Dimmer) OFF/ ON/ AUTO: You can change
the brightness of the display window during the
power-on status.
Settings
Description
4. Rotate the volume knob clockwise or
counterclockwise to adjust the level.
DIM ON
The display window
becomes dark.
5. Press the volume knob to confirm the setting.
DIM OFF
The display window
becomes bright.
3
DIM AUTO
The dimmer operates
according to the car
dimmer setting.
Operating
3. Rotate the volume knob to select the item and
press it.
13
If you want to return to the previous step, press
.
On the Remote Control
1. Press and hold FUNC/ • MENU.
2. Press w / s to select [SOUND], [LIGHT], or
[OTHER] and press ENTER.
3. Press w / s to select the mode and press
ENTER.
4. Press w / s to adjust the level.
5. Press ENTER to confirm the setting.
If you want to return to the previous step, press
.
For [SOUND] setting
You can adjust sound quality by adjusting the level
of BASS (bass), MID (middle), TRB (treble), BAL (left/
right speaker), FAD (front/rear speaker) and SWC
(Sub woofer control).
- When you set the EQ to USER 1/2 mode. : You can
adjust the level of BASS (bass), MID (middle), TRB
(treble) BAL (left/right speaker), FAD (front/rear
speaker) and SWC (Sub woofer control).
 DIM L (Dimmer Level): When you set DIM to ON/
AUTO, you can adjust the dimmer level. (-2, -1, 0,
+1, +2)
14
Operating
For [OTHER] setting
 AUX (Auxiliary) ON/ OFF
It is possible to use auxiliary equipment with this
unit. Activate the auxiliary setting when using
auxiliary equipment connected to this unit.
 DEMO OFF/ ON
You can change the initial indication on the
display to information name (function name, EQ
name, etc...) while listening to a source.
 SW (Subwoofer) OFF/ SW 55 Hz/ SW 85 Hz/ SW
120 Hz
You can enable the subwoofer.
SW OFF <-> SW 55 Hz <-> SW 85 Hz <-> SW 120
Hz.
3
Operating
 A-EQ (Auto EQ) ON/ OFF
AUTO EQ operates only in the music file
supported with genre in the device. When you
set AUTO EQ to ON, POP, CLASSIC, ROCK, or JAZZ
is automatically selected according to the music
genre.
 BEEP 2ND/ ALL
BEEP 2ND: The beep is generated when a key is
pressed for longer than 2 seconds.
BEEP ALL: The beep is generated when any kesy
is pressed.
 CLK (Clock)
For the model RDS is not supported unit or even
for a RDS supported unit.
- When RDS CT information is not received and
then you set CT to OFF, you can adjust the time
by yourelf. Set the clock as follows ;
1. Select a source to TUNER.
2. Press the F to select the CT and then set
CT to OFF.
( Refer to the " Adjusting TUNER settings " on
the pages 18 for setting the CT (Clock Time)
ON/ OFF.)
3. Press ` on the unit to select [OTHER] and
then select CLK by rotating the volume
knob.
4. Set the hour by rotating the volume knob.
5. Press the volume knob to confirm the hour.
6. Set the minute by rotating the volume knob.
7. Press the volume knob to confirm the
minute.
- When RDS CT information is received ;
The clock is displayed according to the RDS CT
information.
- When RDS is not supported, set the clock
according to 3-4 steps.
Listening to a CD
[LCS510IR/ LCS510UR]
1. Insert a CD.
2. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W/S on the remote control.
[LCF610IR]
1. Press the OPEN to open the control panel.
2. Insert a CD.
3. Close the control panel.
4. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W/S on the remote control.
, Note
Make sure to press B after pressing OPEN to
eject a disc. Refer to the picture above.
Pausing or restarting CD
playback
1. Press N on the unit to pause playback.
Or press d/M on the remote control.
2. Press it to resume playback.
Searching for a section within
a track/ file
1. Press and hold A/ D on the unit for about 1
second during playback.
Or press and hold c / v on remote
control.
2. Press N on the unit at the point you want.
Or press d/M on the remote control.
Operating
Skipping to another track/ file
Press A/ D on the unit.
Or press c/v on remote control.
Or
1. Press the volume knob on the unit.
Or press ENTER on the remote control.
2. Rotate the volume knob on the unit to select a
desired ROOT or folder and press it.
Or press w / s and press ENTER on the remote
control.
3. Rotate the volume knob on the unit to select a
desired track/ file and press it.
Or press w / s and press ENTER on the remote
control.
To skip to previous track, press briefly A with
in 3 seconds of playing time.
Checking information about
your music
Playing back tracks/ files in a
way you want
For using applicable buttons
1. Press INT/ RPT/ SHF.
2. Press it again to cancel.
Or
Using the FUNC button
On the unit
1. Press F .
2. Rotate the volume knob to select an item and
press it.
3. Rotate the volume knob to select the option.
4. Press the volume knob to set the option.
If you want to return to the previous step, press
.
On the Remote Control
1. Press FUNC/ • MENU.
MP3/WMA files often come with tags. The tag gives
the Title, Artist or Album.
2. Press w / s to select an item and press it.
Press DISP repeatedly during MP3/WMA/CD TEXT
file playback. If there is no information, "NO TEXT"
will be shown in the display window.
4. Press ENTER to set the option.
3. Press w / s to select the option.
If you want to return to the previous step, press
.
 INT (Intro Scan)
The first 10 seconds of all tracks/ files (INT) or
INT)
each files in the current selected folder (
on the disc are played.
 RPT (Repeat)
The current selected tracks/ files (1 RPT) or folder
RPT) on the disc is played repeatedly.
(
 SHF (Shuffle)
Each files in the current selected folder
SHF) or all of the tracks/ files (SHF) on
(
the disc is played randomly. During random
playback, even if you press A, you won't go back
to the previous track.
3
Operating
, Note
15
16

Operating
, Note
: The icon is displayed during MP3/WMA
playback.
 MP3/WMA Disc compatibility with this
unit is limited as follows:
1. Sampling Frequency / 8 kHz to 48 kHz
(MP3) 22.05 kHz to 48 kHz (WMA).
2. Bit rate / within 8 kbps to 320 kbps (include
VBR) (MP3) 32 kbps to 320 kbps (WMA).
3. CD-R/CD-RW file system should be "ISO
9660".
3
Operating
4. If you record MP3/WMA files using software
which cannot create a FILE SYSTEM, for
example "Direct-CD" etc., it will not be
possible to playback MP3/WMA files. We
recommend that you use "Easy-CD Creator"
which creates an ISO 9660 file system.
You have to set the disc format option
to [Mastered] in order to make the discs
compatible with the LG players when
formatting rewritable discs. When setting the
option to Live File System, you cannot use it
on LG players.
(Mastered/Live File System: Disc format system
for Windows Vista)
Cusotmers should also note that
permission is required in order to
download MP3/WMA files and music from
the Internet. Our company has no right to
grant such permission. Permission should
always be sought from the copyright
owner.
Listening to music
from an external
device
1. Connect an external device to the AUX jack with
line input cable.
2. Select a source to AUX.
3. Play the connected Auxiliary Equipment.
4. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W/S on the remote control.
Preventing radical changes in
volume as switching sources
Only when you set AUX to ON as switching sources,
you can adjust the volume level of each source to
prevent radical changes in volume by selecting
GAIN 0/ +6.
1. Press F on the unit.
Or press FUNC/ • MENU on the remote control.
2. Rotate the volume knob on unit.
Or press w / s on the remote control to set
the option. (GAIN 0/ +6)
3. Press the volume knob on unit.
Or press ENTER on the remote control to
confirm the setting.
4. If you want to return to the previous step, press
.
Operating
Listening to the radio
Listening to a preset station
1. Press SRC repeatedly to select a source to
TUNER.
2. Press the volume knob on the unit.
Or press ENTER on the remote control.
2. Press BAND repeatedly to select a desired band.
3. Rotate the volume knob to select a preset
station.
Or press w / s on the remote control.
17
1. Press BAND repeatedly to select a desired band.
3. For manual search, press and hold A/ D on
the unit until “MANUAL“ is displayed. Then press
it repeatedly to select a desired frequency.
Or press and hold c / v on the remote
control.
For auto search, press A/ D on the unit until
“SEARCH” is displayed.
Or press c / v on the remote control.
Storing desired frequencies
manually
1. Press BAND to select a desired band you want
to store.
2. Press and hold A/ D on the unit until the beep
sound is heard.
Or press and hold c / v on the remote
control.
3. Press it repeatedly to select a desired frequency.
4. Press and hold one of preset buttons among
1 to 6 until the beep sound is heard. (Only
LCS510IR/ LCS510UR)
Press the volume knob and rotate the volume
knob to select a preset station among 1 to 6
and then press and hold the volume knob until
the beep sound is heard. (Only LCF610IR)
5. Repeat steps 1 to 4 to preset other stations.
, Note
When a station is stored on the preset
numbers on which another station of the same
band has already been preset, the previously
preset station is automatically erased.
Or
Press BAND and then the desired preset button
among 1 to 6. (Only LCS510IR/ LCS510UR)
3
Operating
4. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W/S on the remote control.
4. Press the volume knob.
Or press ENTER on the remote control.
18
Operating
Adjusting TUNER settings
On the unit
1. Press F .
2. Rotate the volume knob to select an item and
press it.
3. Rotate the volume knob to set the option and
press it.
4. If you want to return to the previous step, press
.
On the Remote Control
3
1. Press FUNC/ • MENU.
2. Press w / s to select an item and press ENTER.
Operating
3. Press w / s to set the option and press ENTER.
4. If you want to return to the previous step, press
.
 A/S (Auto Store)
The six strongest broadcasting frequencies will
be stored under preset button 1 - 6 in the order
of their signal strength. To cancel, press the
volume knob (or ENTER on the remore control).
 P/S (Preset scan)
Each preset station appears. To cancel, press the
volume knob (or ENTER on the remore control).
 SENS (Tuner sensitivity) MID/ HI/ LOW
In an area in which signal reception is weak, it
helps the tuner to search more stations. The
weaker the reception is, the lower option you
should set to.
RDS (OPTIONAL)
 PTY (Program type)
It searches the radio stations by program type of
FM tuner.
The program types are displayed as follows.
NEWS
FINANCE
EASY M
AFFAIRS
CHILDREN
LIGHT M
INFO
SOCIAL
CLASSICS
OTHER M
SPORT
RELIGION
EDUCATE
PHONE IN
JAZZ
DRAMA
TRAVEL
COUNTRY
CULTURE
LEISURE
NATION M
SCIENCE
DOCUMENT
OLDIES
VARIED
POP M
FOLK M
WEATHER
ROCK M
 AF (Alternative frequency) ON/ OFF
When the reception quality drops, the tuner
automatically changes to another station in the
network, broadcasting a better reception quality,
using the PI and AF codes.
 REG (Region) ON/ OFF
REG ON: The unit switches to another station,
within the same network, broadcasting the same
program when the receiving signals from the
current station become weak.
REG OFF: The unit switches to another station,
within the same network when the receiving
signals from the current station become weak.
( In this mode, the program may differ from the
one currently received.)
 TA (Traffic Announcement) ALARM/ SEEK
TA ALARM: When the tuned station has no TP
information for 5 seconds, a double beep sound
is output.
TA SEEK: When the tuned station does not
receive TP information for 5 seconds, the receiver
retunes to the next station that has the TP
information.
 PI (Programme Identification) SOUND/ MUTE
PI SOUND: When the frequency of a tuned
station switches to an AF (Alternative frequency)
with an unidentified PI, it keeps the sound.
PI MUTE: When the frequency of a tuned station
switches to an AF with an unidentified PI, it
mutes the sound until the PI is identified.
 CT (Clock Time) ON/ OFF
You can use the RDS CT information to update
the time. When RDS CT information is not
received and then you set CT to OFF, you can
adjust the time by yourself. Refer to the page 14
for setting the clock.
Operating
19
Using an USB device
 When you connect a partitioned USB device into
the unit, only the first partition is recognized on
it.
1. Open the USB cover.
 Some USB device may not work with this unit.
2. Connect the USB device.
 Digital camera and mobile phone are not
supported.
3. Press SRC repeatedly to select a source to USB.
4. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W/S on the remote control.
 USB Port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
 Using NTFS file system is not supported. (Only
FAT (16/ 32) file system is supported.
Moving to another drive
Recording to USB from CD or
FM tuner
1. Open the USB cover and connect it to the unit.
3
2. Select CD or FM tuner.
Operating
When connecting this unit to multi reader, press
BAND on the unit (or DRV on remote control) to go
the next drive. Each time you press the button, the
driver modes change.
Quick Search of a desired file
3. Start playback.
You can select and play a desired file regardless of
the order in USB.
4. Press R to start recording.
For one track CD recoridng, press it once.
For all tracks recording, press and hold it until
the beep is heared.
1. Press the volume knob on the unit.
Or press ENTER on the remote control.
2. Rotate the volume knob on the unit to select a
desired ROOT or folder and press it.
Or press w / s and press ENTER on the remote
control.
3. Rotate the volume knob on the unit to select a
desired track/ file and press it.
Or press w / s and press ENTER on the remote
control.
, Note
Other functions are same with "Listening to a
CD". Refer to page 14 -15.
Playable USB device
Requirement
 Do not extract the USB device during operation
(play, etc.).
 An USB device which requires additional
programme installation when you have
connected it to a computer, is not supported.
 Regular back up is recommended to prevent
data loss.
 If you use a USB extension cable, USB HUB, USB
Multi-reader, or external HDD, the USB device
may not be recognized.
5. Press it again to stop.
, Note
 Only in CD and FM tuner, recording is
available.
 Do not remove the USB device during
recording, or an incomplete file may be
made and not deleted on PC.
 When USB memory is full, “Not Enough
Memory” displays and stops recording.
 For tuner recording, the broadcastings are
recorded by 20 moments on a file name.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
20 Operating
Listening to music
by connecting iPod/
iPhone [LCS510IR/
LCF610IR]
Playing back tracks/ files in a
way you want
You can enjoy iPod/ iPhone-stored music on the
unit by connecting it to the USB connector using
the appropriate cable.
3. Rotate the volume knob to select the option.
On the unit
1. Press F .
2. Rotate the volume knob to select an item and
press it.
4. Press the volume knob to set the option.
If you want to return to the previous step, press
.
On the Remote Control
3
1. Press RPT/ SHF.
Operating
[LCS510IR]
[LCF610IR]
1. Open the USB cover.
2. Connect the iPod/ iPhone.
3. Press SRC to select a source to USB.
4. Rotate the volume knob to adjust the volume
on the unit.
Or press VOLUME W/S on the remote control.
, Note
Refer to the page 21 to check the compatible
iPod model for this unit.
Pausing or restarting playback
1. Press N on the unit to pause playback.
Or press d/M on the remote control.
2. Press it to resume playback.
Searching for a section within
a track/ file
During playback, press and hold A/ D and then
release at a point you want.
Checking information about
your music
MP3/WMA files often come with tags. The tag gives
the Title, Artist or Album.
Press DISP repeatedly during MP3/WMA file
playback. If there is no information, "NO TEXT" will
be shown in the display window.
2. Press it again to cancel.
Or
1. Press FUNC/ • MENU.
2. Press w / s to select an item and press ENTER.
3. Press w / s to select the option.
4. Press ENTER to set the option.
If you want to return to the previous step, press
.
 RPT (Repeat)
The current selected tracks/ files (1 RPT) or folder
(
RPT) on the iPod is played repeatedly.
 SHF (Shuffle)
Each file in the currently selected album
SHF) or all of the tracks/ files (SHF) on the
(
iPod are played randomly.
During random playback, even if you press A,
you won't go back to the previous track.
 SPD (BOOK SPEED)
You can adjust the audiobook speed of iPod to
NOR (Normal), SLOW, or FAST.
Operating
21
Playing back files by music
menus
You can check files by music menus and play it
back.
The music menus are as follows.
PLAYLISTS / ARTISTS / ALBUMS / GENRES
/ SONGS / COMPOSER / AUDIO BOOK /
PODCAST / ...
1. Press the volume knob on the unit.
Or press ENTER on the remote control.
2. Rotate the volume knob on the unit to select a
music menu and press it.
Or press w / s on the remote control.
4. Press the volume knob on the unit to confirm
the setting.
Or press ENTER on the remote control.
If you want to return to the previous step, press
.
Compatible iPod models
iPod classic (5th/ 6th generation)
iPod nano (1st/ 2nd/ 3rd/ 4th/ 5th generation)
iPod touch (1st/ 2nd/ 3rd generation)
iPhone
iPhone 3G
iPhone 3GS
iPhone 4
We recommend that you use the OS
Version 4.2.1 or more.
3
Operating
3. Rotate the volume knob on the unit to select a
file.
Or press w / s on the remote control.
“Made for iPod” means that an electronic accessory
has been designed to connect specifically to iPod
and has been certified by the developer to meet
Apple performance standards.
“Works with iPhone” means that an electronic
accessory has been designed to connect
specifically to iPhone and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
iPod is a trademark of Apple Inc., registered in the
U.S. and other countries.
iPhone is a trademark of Apple Inc.
22 Troubleshooting
Troubleshooting
Symptoms
Cause
Solution
Power doesn't turned on.
Leads and connectors are not
properly.
Confirm once more that all connections
are correct.
The fuse is blown.
Rectify the problem that caused the fuse
to blow, and then replace it. Be very sure
to install the correct fuse with the same
rate.
Noise and other factors
are causing the built in
microprocessor to operate
incorrectly.
Turn the unit off and then on again.
No sound is heard.
Cables are not connected
correctly.
Connect the cables correctly.
4
There's audio skipping.
This unit is not firmly secured.
Secure this unit firmly.
Troubleshooting
The playback is not possible.
The disc is dirty.
Clean the disc.
The disc of unplayable type is
loaded.
Check what type the disc.
The signal strength of the
stations is too weak. (when
tuning in with automatic
tuning.)
Tuned in the stations manually.
No station has been preset
or preset stations have been
cleared. (When tuning by
scanning preset stations.)
Preset the stations. (Refer to the page
17.)
iPod/ iPhone does not work.
Check whether iPod/ iPhone
is connected to the unit
correctly.
Connect it to the unit correctly.
The unit does not operate
correctly even when the
appropriate remote control
buttons are pressed.
Battery power is low.
Load a new battery.
The unit doesn't operate.
Radio stations cannot be
tuned in.
Appendix 23
Specifications
USB
Version: USB 1.1 or USB 2.0 Full Speed
General
Bus Power Supply (USB): DC 5V
Output Power: 53 W x 4 CH (Max.)
Line OUT (OPTIONAL)
Power Source: DC 12 V
Speaker impedance: 4 Ω
1A
Frequency Response: 20 Hz to 20 kHz
Output Voltage: 2 V (Max.)
Ground System: Negative
Dimensions (W x H x D): 178 x 50 x169 mm (without
Control Panel)
Subwoofer (OPTIONAL)
Net Weight: 1.37 kg
Output Voltage: 2 V (Max.)
TUNER
FM Tunning Range:
Frequency Response: 20 Hz to 120 Hz
 Design and specifications are subject to change
without notice.
87.5 to 108.0 MHz
S/N Ratio: 55 dB
Distortion: 0.7 %
Usable Sensitivity: 12 dBμV
AM (MW) Tunning Range:
520 to 1720 kHz or 522 to 1620 kHz
S/N Ratio: 50 dB
Distortion: 1.0 %
Usable Sensitivity: 28 dBμV
Frequency Response: 20 Hz to 20 kHz
S/N Ratio: 80 dB
Distortion: 0.12 %
Channel Separation (1 kHz): 55 dB
AUX
Frequency Response: 20 Hz to 20 kHz
S/N Ratio: 80 dB
Distortion: 0.1 %
Channel Separation (1 kHz): 45 dB
Max Input Level (1 kHz): 1.1 V
5
Appendix
CD
Download PDF