LG | LAC-M8600 | LG LAC-M8600 Owner’s Manual

ENGLISH
CAR CD/MP3/WMA Receiver
OWNER’S MANUAL
MODEL : LAC-M8600
Please read this instruction booklet carefully and completely
before connecting, operating or adjusting this product.
R
Safety note
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT SPLIT
COVER(OR BACK) NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user about the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
Always operate the vehicle in a safe manner.
Do not become distracted by the vehicle while driving, and always be fully
aware of all driving conditions. Do not change settings, or any functions.
Pull over in a safe and legal manner before attempting such operations.
Do not use for many hours at extremely low or high temperature.
(-10~60°C)
To reduce the risk of electric shock, do not remove the cover or back of
this product. There are no user-serviceable parts inside.
Refer servicing to qualified service personnel.
To reduce the risk of fire or electric shock, do not expose this product to
dripping or splashing water, rain, or moisture.
Due to high temperature outside of the unit, please use the unit only
installed in a car.
CAUTION : VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED.
CAUTION : This product uses a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully
and retain it for future reference. Should the unit require maintenance, contact an
authorized service center.
Performing controls, adjustments, or carrying out procedures other than those
specified herein may result in hazardous radiation exposure.
To prevent direct exposure to the laser beam, do not try to open the enclosure.
Visible laser radiation when open. DO NOT STARE INTO BEAM.
2
Safety note
• A defective or soiled disc inserted into the unit can cause the sound to
drop during playback.
• Handle the disc by holding its inner and outer edges.
• Do not touch the surface of the unlabeled side of the disc.
Do not stick paper or tape, etc. on the surface.
Do not expose the disc to direct sunlight or excessive heat.
8 cm
This unit cannot use 8 cm discs (use 12cm discs only).
If you insert an 8cm disc by mistake, press the EJECT button for a long
time with the front panel opened.
• Clean the disc before playback. Wipe the disc from the center outward
with a cleaning cloth.
• Never use solvents such as benzine or alcohol to clean the disc.
Periodically wipe the contacts on the back of the front panel with a cotton
swap moistened with alcohol.
3
Table of contents
Safety note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-14
Bluetooth operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-19
Radio operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
CD/MP3/WMA operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4
Before use
Detachable front panel
The front panel can be detached to prevent theft.
1
2
3
4
2
Press
(RELEASE) to open the front panel.
Hold the left part the front panel.
Pull the front panel.
Place the front panel in the supplied protective case.
3
4
Front panel
Protective Case
Attachable front panel
The front panel can be detached to prevent theft.
1 Align the right side of the panel with the stopper.
2 Push the left side or panel into the unit until it clicks.
Notes
• When detaching or attaching the front panel, do not press
the display or control buttons.
• The control buttons may not work properly if the front panel
is not attached properly. If this occurs, gently press the front
panel.
• Do not leave the front panel in any area exposed to high
temperatures or direct sunlight.
• Do not drop the front panel or otherwise subject it to a strong
impact.
• Do not allow such volatile agents as benzine, thinner, or
insecticides to come into contact with the surface of the front
panel.
• Do not try to disassemble the front panel.
5
1
2
Front Panel
1
18
1
2
3
4
5
6
7
8
2
3
4 5
17
16
6
15
7
14
13
9
10
11
12
13
14
15
16
POWER [PWR / MUTE]
• VOLUME [VOL]
• SELECT
• MENU
• SKIP ?m M? / SEARCH m M
• SEEK/ TUNE
• MP3 TRACK +10/-10 MP3 WMA
• FOLDER UP/DOWN MP3 WMA
• PRESET SCAN [PS]
MICROPHONE [MIC]
SOURCE [SRC]
REMOTE SENSOR
EQUALIZER [EQ/WOW/XDSS]
DISPLAY WINDOW
• EJECT Z
• [TILT]
12
8
11
10
[IMAGE]
PRESET STATION [1~6]
SHUFFLE [SHF]
REPEAT [RPT]
INTRO SCAN [SCAN]
PLAY/PAUSE B/X
[BAND/END]
• AUTO STORE [AS]
• PRESET SCAN [PS]
17 [SEND]
18 RELEASE
6
9
Remote control
1
2
3
4
5
6
7
POWER [PWR] / MUTE
SELECTION [MENU/SEL]
SOURCE [SRC]
PLAY / PAUSE B/X
INTRO SCAN [SCAN]
SHUFFLE [SHF]
• MP3 TRACK +10 MP3 WMA
• FOLDER UP U MP3 WMA
8 • CD SKIP / SEARCH ?m m
• SEEK / TUNE ?m m
9 [BAND]
10 VOLUME UP
/ DOWN
1
2
3
4
11
12
5
6
7
13
8
14
9
15
16
11
12
13
14
NUMBER [#]
REPEAT [RPT]
NUMBER [0 -9]
• CD SKIP / SEARCH M M?
• SEEK / TUNE M M?
15 DISPLAY [DISP.]
16 • MP3 TRACK -10 MP3 WMA
• FOLDER DOWN u MP3 WMA
Battery installation
1
2
3
10
Remove the battery holder with a pencil or ball point pen.
Install the battery on the battery holder.
Install the battery holder back into its original position.
Notes
• Use only one CR2025 (3V) lithium battery.
• Remove the battery if the remote control is not used for a
long period of time.
• Do not leave the product in a hot or humid place.
• Do not handle the battery using metallic tools.
• Do not store the battery together metallic materials.
• In the event of battery leakage, wipe the remote control
completely clean and install a new battery.
7
Installation
Basic Installation
Before installing, make sure that the ignition switch is set to
OFF and remove the terminal of the car battery to avoid
short-circuiting.
Bend the claws
according to
the thickness
of the
dashboard
1
2
3
4
Remove the existing receiver unit.
Make the necessary connections.
Install the installation sleeve.
Install the unit into the installation sleeve.
Front panel
Removing the existing receiver unit
If there is already an installation sleeve for the receiver unit in
the dashboard, it must be removed.
A
1
2
3
A
Remove the rear support from the unit.
Remove the front panel and trim ring from the unit.
Insert the lever A into the hole on one side of the unit.
Perform the same operation on the other side and pull the
unit out from the mounting sleeve.
ISO-DIN Installation
1
4
5
6
3
2
1
2
3
4
5
6
Slide the unit into the ISO-DIN frame.
Install screws removed from the old unit.
Slide the unit and frame into the dash opening.
Install the dash panel or adapter plate.
Install the trim ring to in unit.
Install the faceplate by fitting the right edge into position
then pushing the left edge closed.
Front panel
8
Connection diagram
Before connecting, make sure that the ignition switch is set to OFF, and remove the battery #
terminal to avoid short circuits.
B
A
PHONE MUTE (ORANGE)
GROUND(-) (BLACK)
DIMMER (PINK)
DIMMER SWITCH
TO IGNITION (RED)
IGNITION SWITCH
TO BATTERY(+) (YELLOW)
POWER ANTENNA (BLUE)
AMPLIFIER
(Optional)
BATTERY
C
1
REMOTE ON (BLUE/WHITE)
2
POWER
ANT
3
4
5
CONTROL RELAY
6
7
8
1.
2.
3.
4.
5.
6.
7.
8.
9
WHITE FL+
WHITE/BLACK STRIPE FLGRAY FR+
GRAY/ BLACK STRIPE FRGREEN RL+
GREEN/ BLACK STRIPE RLVIOLET RR+
VIOLET/ BLACK STRIPE RR-
Connection
C Speaker Connections A From antenna
B To the wiring of the vehicle colors of leads.
8
7
6
5
4
3
2
1
L
• BLACK
: This lead is for the ground connection.
• ORANGE
: This lead is for the phone line connection.
• PINK
: This lead is for the dimmer line
connection.
• RED
: This lead is for connection to the power
supply terminal when the ignition switch is
set to ACC.
• YELLOW
: This lead is for connection to the battery
(back-up) terminal from which power is
always supplied.
• BLUE
: This lead is for the power antenna
connection.
FRONT
R
L
• BLUE/WHITE : This lead is for the remote amplifier on
connection.
REAR
R
Connecting to Auxiliary Equipment (Optional)
AUDIO IN
RR
RL
FR
• Connect the AUDIO INPUT connector of this unit to the
AUDIO OUTPUT connector of the Amplifier.
• Connect the AUX INPUT connector of this unit to the
AUX OUTPUT connector of the Auxiliary Equipment.
AUX
FL
R
L
Auxiliary Device
Amplifier
10
Basic operation
Turning the unit on
Press PWR/MUTE (POWER/MUTE
on the remote control) or any other button.
Note
When you insert the CD in the CD slot, the unit turns on.
Turning the unit off
Press and hold the PWR/MUTE (POWER/MUTE
seconds.)
on the remote control for more than 1.2
Insert a disc
1
2
Press Z/TILT to open the front panel.
The disc is drawn in and playback starts automatically.
Eject a disc
Press Z/TILT to open the front panel. The disc automatically ejects from the loading slot.
When the disc is ejected by pressing Z/TILT during playback, it will be loaded automatically
after 10 seconds unless you pull out the disc from the unit.
Selecting a source
Press SRC repeatedly to select a source.
The indicator lights up in the following order. TUNER → CD → AUX → TUNER...
Adjusting the volume
Rotate VOL./MULTI (Press VOLUME
on the remote control) to adjust the sound level.
Note
When you turn the unit off, the current volume level is automatically memorized. Whenever
you turn the unit back on, it will operate at the memorized volume level.
Mute
1
2
Press PWR/MUTE (POWER/MUTE
To cancel it, press again.
on the remote control) to cut the sound.
Checking the clock
You can see the clock pressing IMAGE/DISP (DISP. on the remote control).
11
Basic operation
Changing the monitor angle
Press and hold Z/TILT to adjust the front panel to an easily viewable angle.
• The angle of front panel can be adjusted up to 3 steps.
• The adjusted LCD panel angle will be memorized and the monitor panel will
automatically return to this angle the next time the monitor panel is opened.
Setting the menu
1
2
3
4
Press and hold VOL./MULTI (MENU/SEL on remote control) for about 1 second.
The menu screen appears.
Beep y ECM y Clock y SRS focus
Push VOL./MULTI up or down to scroll between menus.
(Press the U u on the remote control.)
Push VOL./MULTI left or right to select the settings of your choice.
(Press ?m m/M M? on the remote control.)
Press VOL./MULTI shortly to exit the main screen.
SRS focus
( HIGH / LOW )
Set the SRS focus quality.
Beep
( 2ND / ALL )
Set the beep sound every time a button is pressed.
• 2ND mode : The beep is only generated when a key is long
pressed (1 sec)
• ALL mode : The beep is generated when any key is pressed.
Clock
Set the current time. : up v / down V / left b / right B
• Push the the VOL/MULTI (Press ?m m M M? on the remote
control) in left or right direction on the menu screen to move to the
next stage.
• Push the the VOL/MULTI (Press U u on the remote control) in up
or down direction on the menu to move to the desired number.
ECM
(Echo Cancellation
Mode)
It is to decrease any echo phenomenon of voice coming from the
Bluetooth phone of the other party when working Bluetooth.
Control the mode(1-3) to the appropriate condition when talking over
the phone.
12
Basic operation
Using the EQ (Equalizer)
The equalizer lets you adjust the equalization to match the acoustic characteristics of
the car’s interioras desired.
Press the EQ/WOW/XDSS repeatedly. The indicator lights up in the following order.
POP t Classic t ROCK t JAZZt VOCAL t SALSA t SAMBAt USER1 t
USER2 t OFF
• POP
: Optimized for R&B, Soul and Country music.
• Classic : Optimized for orchestral music.
• ROCK : Optimized for Hard Rock and Heavy Metal music.
• JAZZ
: Sweet sound with soft feeling.
• VOCAL : Powerful realism with strong sound quality.
• SALSA : Reproduces salsa music acoustics.
• SAMBA : Reproduces samba music acoustics.
• USER1 : Use the menu to set the sound level you want.
• USER2 : Use the menu to set the sound level you want.
You can adjust each sound level to your preference. Once you select a USER mode and then
make an adjustment, it is automatically stored for the currently selected USER mode.
See “Adjusting the sound level” below.
Adjusting the sound level
1
2
Press VOL./MULTI (MENU/SEL on the remote control) repeatedly to select the mode you
want to adjust from volume, equalizer, balance and fader.
The indicator lights up in the following order.
VOL t EQ t BAL t FAD t MIC
Rotate VOL./MULTI (Press VOLUME
on the remote control) to adjust the sound
quality.
Turn right
Turn left
VOL
EQ
BAL
Increase the volume level.
Decrease the volume level.
Increase the equalizer level.
Decrease the equalizer level.
Decrease the level of the right speaker(s).
Decrease the level of the left speaker(s).
FAD
Decrease the level of the rear speaker(s).
Decrease the level of the front speaker(s).
MIC
Increase the microphone level.
Decrease the microphone level.
Push VOL./MULTI left or right to move the next stage.
(Press ?m m/M M? on the remote control) : EQ setting
Note
Normally the function works as sound level control. You can not select EQ to adjust the EQ
level when it is using the EQ (POP, Classic, ROCK JAZZ, VOCAL, SALSA, SAMBA) mode.
13
Basic operation
XDSS/XDSS+ (Extreme Dynamic Sound System)
Press and hold the EQ/WOW/XDSS repeatedly to select XDSS or XDSS+
XDSS t XDSS+ t By pass
XDSS/XDSS+ : Improve the treble, bass sound.
SRS (Sound Retrieval System)
1
2
Press and hold the EQ/WOW/XDSS to select SRS.
SRS (FOCUS t TRU BASS t 3D-STEREO t WOW) t By pass
Press the EQ/WOW/XDSS repeatedly to select sub SRS.
• FOCUS
: Improve the resolution sound.
• TRUBASS
: Improve the bass sound to make it spectacular.
• 3D-STEREO : Enjoy the 3D surround effect.
• WOW
: Enjoy the SRS and TruBass simultaneously.
Notes
•
is a trademark of the SRS Labs, Inc.
• WOW technology is incorporated under license of the SRS Labs, Inc.
• You can not use the EQ function when SRS function is enabled.
Using the IMAGE
Press and hold IMAGE/DISP repeatedly to select the background you want in the display window.
You can select one of 10 modes. It displays the change of sound output during play.
14
Bluetooth operation
Using a Bluetooth wireless connection
Your unit supports Bluetooth wireless connections. You can set up
a wireless link with a Bluetooth phone.
Starting Bluetooth on your phone
Your phone’s Bluetooth feature may be set to off by default.
To use your car Bluetooth feature, Bluetooth must be turned on in
your phone.
Note
Refer to your phone’s user guide.
Pairing your unit and Bluetooth phone
Pairing links your unit and Bluetooth phone, and is required only once for the initial setup.
Before you start the pairing procedure, make sure the Bluetooth feature is turned on in to
your Bluetooth phone. Refer to your Bluetooth phone’s user guide.
1
2
3
4
5
6
Press and hold SEND button to connect your Bluetooth phone.
Hands-free connection and headset may operate depending on the type of the phone
you trying to connect.
You can select any of the below by press and hold the SEND button repeatedly
Handsfree t Headset t OFF (No display)
If your Bluetooth phone does not support the handsfree connection, then initiate the
headset connection.
The
indicator flashes.
Set the Bluetooth phone to look for your unit.
When the Bluetooth phone displays the device name, select the device.
The Bluetooth phone displays the PIN code enter screen, enter the PIN code.
LG CAR AUDIO PIN CODE : 1234
When your unit successfully paired with your Bluetooth phone, the flashing indicator stops.
Notes
• Your unit keeps lists of pairing you recently connected. A maximum of 4 pairing numbers
can be saved.
• The Bluetooth phone which has a previous record showing that it has successfully connected will automatically start the connecting process when starting a car.
• Unlike the hands-free functionality, Headset connection will allow only two functions
“answering calls” and “making a call from the latest call”.
Also the caller’s number is not displayed when answering calls.
Bluetooth phone not yet connected
If the Bluetooth phone has not been connected when you try to call up telephone mode,
“Connecting” appears on the screen.
15
Bluetooth operation
Answering and Ending a call
Your unit, Bluetooth phone, or both may ring when you receive a call, press SEND to answer a
call.
To end a call, press BAND/END.
Rejecting a call
When your unit rings, press BAND/END.
If the “Rejecting” function usable, then the phone connected to the device does not support
the rejecting calls function.
Missed call notification
When an incoming call is not answered, the missed call message is displayed on the your
screen.
1 The “Missing Call” appears on the screen.
2 Press SEND button to answer the call.
3 To end the call and hang up the phone, press BAND/END button.
Setting the menu
Once your unit and Bluetooth phone are paired, your phone automatically connects to the unit
when you turn it on the next time. To confirm your unit and Bluetooth phone are successfully
paired and operating property, make a call.
1 If your Bluetooth phone is already connected to a unit, press SEND.
The menu screen appears.
Dial preset t Dial last answered? t Dial last call?
2 Push VOL./MULTI up or down to select the menu.
3 Press SEND to enter the your choose.
Making a call from the latest call : Dial last call?
Your phone keeps a lists of your recently received and dialed even if the calls did not
connected. The lists are sorted from newest to oldest entries.
Your unit keeps recorded of your recently received and dialed on phone.
Press SEND to place a call to entered phone number.
There is case that sending is done by pressing SEND button for a long time depending on
type of mobile phone. (For basic setting, press SEND button shortly.)
“Calling Last Call” appears on the screen.
Note
When you want to make an international call, push VOL./MULTI up to add +.
Push VOL./MULTI toward down to deletes +.
+ can only be added when the detail list of Missed call, Dialled call or Received call is
selected.
16
Bluetooth operation
Dial using a number from the list : Dial last answered?
Your unit keeps a record of your recently received and display.
1 Press SEND.
2 Push VOL./MULTI toward up or down to select the “Dial last answered?” menu.
3 Press SEND.
The “Last answered” and number appears on the screen.
4 Push VOL./MULTI toward up or down to scroll between numbers.
(Or press one of the number 1 ~ 6.)
5 Press SEND to place a call to entered phone number.
Note
When you want to make an international call, push VOL./MULTI toward up to add +.
Push the VOL./MULTI toward down to delete +.
Storing a call number : Dial Preset?
You can easily store up to 6 internal entries for later recall at the touch of a button.
1
2
3
4
5
6
7
Press SEND.
Push VOL./MULTI toward up or down to select the “Dial last answered?” menu.
Press the SEND.
The “Last answered” and number displays on the screen.
When you want to save an international call, push VOL./MULTI up to add +.
Push VOL./MULTI toward down to deletes +.
Press and hold SEND.
Push VOL./MULTI toward up or down to scroll between numbers or press one of the
number 1 ~ 6.
Press SEND.
The selected number has been stored in memory.
(Or press and hold one of the number 1 ~ 6.)
Repeat steps 1 and 4 to save other calls.
The next time, you press the same number 1 ~ 6, the number is recalled from the
memory.
Echo canceling and noise reduction
When you are doing hands-free phoning in the vehicle, you may hear undesired echo
sounds.
This function reduces undesired echo sounds and noise while you are doing hands-free
phoning, while maintaining a certain sound quality.
Please see page 12 for details.
Note
After setting ECM function, ensure to separate Car Audio Front Panel and mount it again.
17
Bluetooth operation
Pairing your unit and Bluetooth device (MP3 Player, MP3 Phone...)
When you activate your Bluetooth device’s linked the unit, you can listen to MP3 with wireless
connections.
1 Press and hold SEND to connect your Bluetooth device.
If connecting through a Bluetooth device, the hands-free connection or headset
connection may operate depending on the type of the phone.
Handsfree t Headset t OFF (No display)
2 If your Bluetooth device does not support the handsfree connection, then initiate the
headset connection.
The
indicator flashes.
3 Set the Bluetooth device to look for your unit.
4 When the Bluetooth device displays the device name, select the device.
5 The Bluetooth device displays the PIN code enter screen, enter the PIN code.
LG CAR AUDIO PIN CODE : 1234
6 When your unit successfully paired with your Bluetooth device, the flashing of indicator
stops.
Playing MP3 files
When you turn Bluetooth on, your Bluetooth device display “Bluetooth” in the home screen.
The Bluetooth remains on until you press turn the device off.
Press SRC repeatedly to select a Bluetooth.
The indicator lights up in the following order.
TUNER → CD → AUX → BLUETOOTH → TUNER...
To play MP3 file stored on your Bluetooth device, refer to your Bluetooth device’s user guide.
Notes
• This function cannot be used with a device that it has no MP3 function.
• In order to use Bluetooth technology, devices must be able to interpret certain profiles.
This unit is compatible with following profiles.
- GAP (Generic Access Profile)
- HSP (Hands Set Profile)
- HFP (Hands Free Profile)
- GAVDP (Generic Audio/Video Distribution Profile)
A2DP (Advanced Audio Distribution Profile)
AVDTP (Audio/Video Distribution Transport Profile)
AVRCP (Audio/Video Distribution Remote Control Profile)
• When recording the keywords and the magic word, park your vehicle in a quiet place with
the windows closed and the heater/air conditioner off.
This is necessary to obtain a higher recognition rate.
18
Bluetooth operation
GAP
GAP is short for Generic Access Profile. This is a basic profile of Bluetooth wireless
technology.
HFP
HFP is short for Hands-Free Profile. This profile is used for hands-free phoning with the
devices featuring Bluetooth wireless technology.
HSP
HSP is short for Head Set Profile. This profile is used for connecting a headset and
for communicating terminal wireless technology.
GAVDP
This profile uses an Initiator (INT)a device (such as a portable player) that initiates a
signalling procedure to send a request to an Acceptor (ACP), - such as headphones etc.
Although this profile specifies signalling transaction procedures between two devices to set
up, terminate and reconfigure streaming channels, using the GAVDP alone, it is required to
use GAVDP in combination with profiles that depend on this profile - the AVRCP and the VDP.
A2DP
Mobile phones and devices with A2DP high quality stereo bluetooth profile.
This profile is based on the GAVDP, and allows advanced audio to be transmitted (audio
streaming) from a Source (SRK) - such as a CD player, to a Sink (SNK), such as headphones.
AVRCP
Based on the GAP Profile, it uses a Controller (CT) - PDA, computer mobile phone etc., that
sends a command to a Target (TG) - TV, discman, headphone etc. The command can be to
Play, record, colour control, volume control etc., depending on the nature of the devices
involved and the scenario. The commands are transported by a new additional protocol,
called the Audio/Video Control Transport Protocol (AVCTP). Some scenarios defined are
Remote Control from a Separate Controller, Remote Control and Audio Stream Between Two
Devices, Remote Controller with LCD.
19
Radio operation
Listening to radio stations
1
2
3
Press SRC to select the radio.
Press BAND/END repeatedly to select a band.
The indicator lights up in the following order. FM1 t FM2 t FM3 t MW(AM)
Seek tuning : Push VOL./MULTI left or right. (Press ?m m M M? on the remote
control.) The tuner will scan the frequencies until a broadcast with strong enough
reception is found.
Manual tuning : Push VOL./MULTI repeatedly up or down.
(Press the ?m m/M M? on the remote control for more than 2 seconds and then
repeatedly.) The frequencies move up or down step by step.
Auto search memory
This function lets you automatically store the 6 strongest broadcast frequencies.
1
2
Press SRC to select the tuner.
Press and hold AS/PS for more than 1 second.
Scanning starts from the currently displayed frequency to higher frequencies and stops
when 6 stations have been preset or the receivable frequencies have been scanned
once.
Storing and recalling broadcast frequencies
You can easily store up to 6 broadcast frequencies for later recall at the touch of a
button.
1
2
3
Select the desired frequency.
Press one of the preset station 1 ~ 6 for more than 1 second.
The number you have pressed will flash in the preset number indicator and then remain
lit. The selected radio station frequency has been stored in the memory.
Repeat steps 1 and 2 to preset other stations.
The next time you press the same preset station 1 ~ 6, the radio station frequency is
recalled from the memory.
Note
As FM1, FM2, FM3 have the same frequency range, up to 18 stations can be preset for FM.
When a station is preset on the preset station button on which another station of the same
band has already been preset, the previously preset station is automatically erased.
To scan the preset stations
Press AS/PS. To stop the scanning, press AS/PS.
To tune in the preset stations
Press the BAND/END to select the desired band and press the desired number (1-6).
The number of the preset station 1 ~ 6 is displayed and the preset station is received.
20
CD/MP3/WMA operation
Playing an Audio CD and MP3/WMA Disc
The unit can play MP3/WMA formatted recordings on CD-ROM, CD-R or CD-RW discs.
Before playing MP3/WMA recordings, read the notes on MP3/WMA Recordings on page 24.
This unit memorizes the last track from the last disc that was listened. The last track remains
in the memory even if you switch off the unit. If you load a disc that has the track memorized,
the track is automatically recalled.
To directly play a file, press NUMBER (#) on remote control and then press the track
number with 0-9 number.
Pause
1
2
CD
MP3
WMA
Press B/X during playback.
To return to playback, press B/X again.
Moving to another track
CD
MP3
WMA
Push VOL./MULTI left or right during playback to select the next track or to return the
beginning of the current track. (Press ?m m/M M? on the remote control.)
Push VOL./MULTI left to select the previous track. (Press ?m m on the remote control.)
(If playing times is less then 4 seconds, there is no operation.)
Search
CD
MP3
WMA
Push VOL./MULTI knob (?m m/M M? on remote control) in left or right direction for about
1 second during playback and then release at the point you want.
Intro scan
1
CD
MP3
WMA
Press SCAN.
FOLDER SCAN appears in the display window. MP3 WMA
(The first 10 seconds of each files in the current selected folder on the disc are played.)
SCAN ALL appears in the display window. CD
(The first 10 seconds of each files on the disc are played.)
Press and hold SCAN for about 1 seconds during playback.
SCAN ALL appears in the display window. MP3 WMA
(The first 10 seconds of each files on the disc are played.)
2
Press SCAN again.
SCAN OFF appears in the display window. (The intro scan is cancelled.)
Repeat
1
CD
MP3
WMA
Press RPT during playback.
1 RPT appears in the display window. CD MP3 WMA
(The current selected music on the disc is played repeatedly.)
Press and hold RPT for about 1 seconds during playback.
FOLDER RPT appears in the display window. MP3 WMA
(The current selected folder on the disc is played repeatedly.)
2
Press RPT again.
RPT OFF appears in the display window. (The repeat mode is cancelled.)
21
CD/MP3/WMA operation
Random
1
CD
MP3
WMA
Press SHF during playback.
FOLDER SHF appears in the display window. MP3 WMA
(The current selected folder on the disc is played randomly.)
SHF ALL appears in the display window. CD
(All the music on the disc is played randomly.)
Press and hold SHF for about 1 seconds during playback.
SHF ALL appears in the display window. MP3
(All the music on the disc is played randomly.)
2
WMA
Press SHF again.
SHF OFF appears in the display window.
(Random playback is cancelled.)
Note
During random playback, if you push VOL./MULTI (press ?m m on remote control) to left,
you won’t go back to the previous track.
CD TEXT / ID3 TAG
CD
MP3
WMA
When playing a disc containing information, you can see the information CD TEXT/ID3 TAG
information.
In a CD TEXT, some information about the disc (disc title, performer and track title) is recorded.
In a ID3 TAG, some information about the file (album title, Performer name, song title,
recording year, music genre and a brief comment )is recorded.
If there is no information, “NO TEXT” will be shown in the display window.
Press the IMAGE/DISP repeatedly during MP3/WMA/CD TEXT file playback.
MP3/WMA TRACK -10/+10
MP3
WMA
(If there is no folder or one folder.)
During playback, push VOL./MULTI (press the u on remote control) down to skip to the previous 10 track, and push VOL./MULTI (press the U on remote control) up to skip to the next 10
track.
MP3/WMA FOLDER UP/DOWN
MP3
WMA
(If there are more than two folders.)
During playback, push VOL./MULTI (press u on remote control) down to go to the previous
folder, and push VOL./MULTI (press U on remote control) up to go to the next folder.
Note
Time display appearing on the display part when playing VBR file may vary and there may be
some difference from actual time (both progress time and VBR are displayed at the same
time when playing file).
22
Troubleshooting
Symptom
Cause
Leads and connectors are not
properly connected.
The fuse is blown.
Noise and other factors are
causing the built-in
microprocessor to operate
incorrectly.
Playback is not
possible.
The disc is dirty.
The loaded disc is of a type this
unit cannot play.
Clean disc.
Check what type the disc.
No sound is
heard.
The volume
level will not
rise.
Cables are not connected
correctly.
Connect the cables correctly.
There’s no
sound.
The volume level is low.
Adjust the volume.
There’s audio
skipping.
This unit is not firmly secured.
Secure this unit firmly.
The unit does
not operate
correctly even
when the
appropriate
remote control
buttons are
pressed.
Battery power is low.
Some operations are prohibited
with certain discs.
Load new battery.
Check using another disc.
Power doesn’t
turn on.
The unit doesn’t
operate.
Correction
23
Confirm once more that all
connections are correct.
Rectify the problem that caused
the fuse to blow, and then replace
it. Be very sure to install the
correct fuse with the same rate.
Turn the unit off and then on.
Specfications
MP3/WMA Disc compatibility with this unit is limited as follows:
1.
2.
3.
4.
Sampling Frequency / 8 - 48kHz (MP3) 22.05 - 48kHz (WMA)
Bit rate / within 8 - 320kbps (include VBR) (MP3) 32 -320kbps (WMA)
CD-R/CD-RW file system should be “ISO 9660”
If you record MP3/WMA files using software which cannot create a FILE SYSTEM, for example
“Direct-CD” etc., it will not be possible to playback MP3/WMA files. We recommend that you use
“Easy-CD Creator” which creates an ISO9660 file system.
Customers should also note that permission is required in order to download MP3/WMA files and
music from the Internet.
Our company has no right to grant such permission.
Permission should always be sought from the copyright owner.
GENERAL
Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50W x 4CH (Max.)
Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DC 12V
Speaker impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Ω
Ground System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Negative
Dimensions (W x H x D) . . . . . . . . . . . . . . . . . . . . . . . .180 x 51 x 171 mm (Without Front Panel)
Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.0 kg
CD SELECTION
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Hz-20 kHz
S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 dB
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.1%
Channel Separation (1kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 dB
RADIO SELECTION
FM
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87.5-107.9 or 87.5-108 MHz
S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 dB
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.7%
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 dBµV
AM (MW)
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .520-1720 or 522-1620 kHz
S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 dB
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.0%
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 dBµV
24
Mobile phone list and manufacturing company applicable
Company
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Nokia
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
LG
LG
LG
LG
LG
list
8910i
6021
3230
3650
6210i
6310i
6230
6230i
6260
6600
9500
6630
6680
6681
N70-1
8800
8801
SGH-D500
SGH-D508
SGH-D600
SGH-Z500
SGH-Z500V
SGH-E770
SCH-V720
SPH-E3700
SCH-A900
SPH-V6900
SPH-V7450
SPH-V7400
SPH-X7700
SPH-M600
SGH-E730
SGH-E720
KF-1000
LP-3900
P7200
S5200
U8290
Company
LG
LG
LG
LG
Motorola
Motorola
Motorola
Motorola
Motorola
Motorola
Sony-Ericsson
Sony-Ericsson
Sony-Ericsson
Sony-Ericsson
Sony-Ericsson
Sony-Ericsson
Sony-Ericsson
Sony-Ericsson
Sony-Ericsson
Sony-Ericsson
QteK
QteK
QteK imate
imate
QteK imate
QteK imate
HP
Siemens
Siemens
Siemens
Panasonic
O2
O2
Palmone
Blackberry
Toshiba
SAZEM
25
list
LG KG800
LG KU730
U8210
KP-4000
E1000
V600
V3 razor
L6
E1
A1000
T68i
T610
K600i
K700i
S700i
V600
K750i
W550i
W800i
P910i
9090
9100
8100
K2
8020
JASJAR
6515
S55
SL75
M75
X70
XDA2 Mini
XDA2 I
Treo 650
7290
A5504T
myX6-2
R
Bluetooth® wireless technology is a system which allows radio contact between electronic
devices within a max. range of 10 meters.
Connecting individual devices under Bluetooth® wireless technology does not incur any
charges. A mobile phone with Bluetooth® wireless technology can be operated via the
Cascade if the connection was made via Bluetooth® wireless technology.
The Bluetooth® word mark and logos are owned by the Bluetooth® SIG, Inc. and any use of
such marks by LG Electronics is under license.
Other trademarks and trade names are those of their respective owners.
P/NO : MFL30126620
Download PDF