LG | LCS710BR | LG LCS710BR Owner’s Manual

OWNER’S MANUAL
CAR CD/MP3/WMA
Receiver
Please read this manual carefully before operating
your set and retain it for future reference.
LCS710BR / LCS710DAB /
LCF810BR / LCF810DAB
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
To reduce the risk of electric
shock, do not remove the cover
or back of this product. There are
no user-serviceable parts inside.
Refer servicing to qualified service
personnel.
To reduce the risk of fire or electric
shock, do not expose this product
to dripping or splashing water, rain,
or moisture.
The temperature of unit’s outside
can be extremely high, please use
the unit after proper installation in
your vehicle.
This unit cannot play 8 cm disc (use
12 cm disc only).
While driving, keep the sound
volume at a proper level.
Do not drop it and avoid heavy
impacts at anytime.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
Always operate the vehicle in a safe
manner. Do not become distracted
by the vehicle while driving, and
always be fully aware of all driving
condition. Do not change settings,
or any functions. Pull over in a
safe and legal manner before
attempting such operations.
Do not use for many hours at
extremely low or high temperature.
(-10 °C to 60 °C)
This unit is for vehicles with a
12-volt battery and negative
grounding. Before installing it
in a recreational vehicle, lorry or
bus, check the battery voltage.
To avoid shorts in the electrical
system, be sure to disconnect the E
battery cable before beginning the
installation.
Getting Started
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by the
European Directive 2002/96/EC.
1
2. All electrical and electronic products
shall be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or the
local authorities.
Getting Started
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service centre.
3
3. The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
“This device is equipped with a portable battery or
accumulator.
Safe way to remove the battery or the battery
from the equipment:
Remove the old battery or battery pack, follow the
steps in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators."
The battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot
use it on LG players.
(Mastered/Live File System : Disc format system for
Windows Vista)
> Caution
When being connected in a wrong way, the
unit displays as follows.
- Antenna / Remote port short : "ON PORT
SHORT CIRCUIT CHECK"
After connecting it again, restart the unit.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you
purchased the product.
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and
other relevant provisions of Directive
1999/5/EC, 2006/95/EC and ECE
Regulation 10.03 (3.2.9).
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere, The
Netherlands
(Tel : +31-(0)36-547-8888)
The unit is compatible with the steering wheel
remote control. The function allows operation
by sending the steering wheel remote control
signal to the unit.
For details, consult with your dealer.
4
1
2
3
4
5
Table of Contents
Table of Contents
16
16
1
Getting Started
2
5
6
7
7
Safety Information
Front panel [LCS710BR / LCS710DAB]
Front panel [LCF810BR / LCF810DAB]
Remote control
– Battery Installation
17
17
17
18
19
2
Connecting
8
About detachable control panel
[LCS710BR / LCS710DAB]
– Attaching the control panel
– Detaching the control panel
About detachable control panel
[LCF810BR / LCF810DAB]
– Attaching the control panel
– Detaching the control panel
Installation
– Basic Installation
– Removing the existing receiver unit
– ISO-DIN Installation
Connection
– Connecting to a car
8
8
9
9
9
10
10
10
10
11
11
3
Operating
12
12
12
12
12
12
12
13
14
14
14
Operation
– Basic operations
– Turning off the sound temporarily
– Using EQ (Equalizer)
– Checking the clock
– Turning off the display light
– Resetting the unit
– Adjusting the general settings
Listening to a CD
– Pausing or restarting CD playback
– Searching for a section within a track /
file
– Skipping to another track/ file
– Checking information about your
music
– Playing back tracks / files in a way you
want
15
15
15
19
19
19
20
20
21
21
21
21
22
22
22
22
23
23
23
23
24
25
25
26
27
28
Listening to music from an external device
– Preventing radical changes in volume
as switching sources
Listening to the TUNER
– Storing desired frequencies manually
– Listening to a preset station
– Adjusting TUNER settings
Listening to the DAB (Only LCS710DAB /
LCF810DAB)
– Storing desired frequencies manually
– Listening to a preset station
– Adjusting DAB settings
Using an USB device / SD card
– Moving to another drive
– Quick Search of a desired file
– Deleting the desired file
– Playable USB device / SD card
Requirement
– Recording to USB device / SD card
Listening to music by connecting iPod /
iPhone
– Pausing or restarting playback
– Searching for a section within a track /
file
– Checking information about your
music
– Playing back tracks / files in a way you
want
– Playing back files by music menus
– 2WAY Control
– Compatible iPod models
Connecting a Bluetooth wireless
technology
– Using the buttons for Bluetooth
wireless technology
– Using a Bluetooth wireless technology
– Adjusting the setting
– WICS (Wireless Controller &
Synchronization)
– Phone compatibility list
4 Troubleshooting
31
Troubleshooting
5
Appendix
32 Specifications
Getting Started
5
Front panel [LCS710BR / LCS710DAB]
a b
c
d
e
f g
h
i
[Front unit detached panel]
1
Getting Started
j
k
l
m
n
o
p q
r
a B
Ejects a disc.
k
b SRC / • OFF
- When pressed, selects function sources.
- When pressed and held, powers unit on or off.
l
c N
Plays and pauses playback.
Temporarily stops the sound.
d Volume knob
- Adjusts volume level.
- Confirms the settings.
- Checks tracks, files or preset stations.
e F
In each mode, sets playback items.
`
Activates setting menu.
f BAND
- Selects a band in Tuner mode.
- Moves to a next USB drive.
iPOD / • TA
- Searches stations that have TA / TP
information, when it is pressed and held.
- Activates 2WAY Control.
g Remote Sensor
h Display window
i 6
Opens the front panel.
j R
Recording to USB / SD card.
s
t
u
v
- Activates BT function.
- Answers a call.
Returns to the previous step.
Ends a call.
m A/D
Skip / Search / Seek / Tune
n EQ
Improves sound quality.
- When pressed, selects the EQ function.
o DISP
- Press it, you can check the clock time.
- Press and hold it, you can turn on /off the
display window and the light of LED buttons.
p INT
Intro scan.
q RPT
Repeats playback.
r SHF
Shuffles playback.
s Numeric buttons (1 to 6)
Selects a numbered preset station in TUNER.
t AUX
If connected to other portable player, you can
enjoy music from it on the unit.
u USB port
v SD card slot
6
Getting Started
Front panel [LCF810BR / LCF810DAB]
a
b
c
d
e
m
n
f
g h
[Front unit detached panel]
1
Getting Started
i
j
k
l
o
a SRC / • OFF
- When pressed, selects function sources.
- When pressed and held, powers unit on or off.
j
b N
Plays and pauses playback.
k
p
q
- Activates BT function.
- Answers a call.
Returns to the previous step.
Temporarily stops the sound.
c Volume knob
- Adjusts volume level.
- Confirms the settings.
- Checks tracks, files or preset stations.
d F
In each mode, sets playback items.
`
Activates setting menu.
e BAND
- Selects a band in Tuner mode.
- Moves to a next USB drive.
iPOD / • TA
- Searches stations that have TA / TP
information, when it is pressed and held.
- Activates 2WAY Control.
f Display window
g Remote Sensor
h OPEN
Opens the front panel.
i R
Recording to USB / SD card.
Ends a call.
l A/D
Skip / Search / Seek / Tune
m EQ
Improves sound quality.
- When pressed, selects the EQ function.
n DISP
- Press it, you can check the clock time.
- Press and hold it, you can turn on /off the
display window and the light of LED buttons.
o AUX
If connected to other portable player, you can
enjoy music from it on the unit.
p USB port
q SD card slot
Getting Started
Remote control
7
i DISP
• Press it, you can check the clock time.
• Press and hold it, you can turn on / off the
display window and the light of LED buttons.
1
k INT
Intro scan.
l Numeric buttons (1 to 6)
Selects a numbered preset station in TUNER.
Battery Installation
a SRC / • OFF
• When pressed, selects function sources.
• When pressed and held, powers unit off.
b FUNC
When pressed, sets playback items in each
mode.
• MENU
When pressed and held, activates setting
menu.
c BAND
Selects a band in Tuner mode.
DRV
Moves to a next USB drive.
d d/M Plays or pauses playback.
e SHF Shuffles playback.
f MUTE Temporarily stops the sound.
g VOLUME W / S
Adjusts volume level.
h c/v
Skip / Search / Seek / Tune
Returns to the previous step.
w/s
• List up / down
• Adjusts settings.
• Moves 10 MP3 / WMA tracks backward or
forward if there is no folder or one folder on a
CD.
• Moves to the previous or next folder if there
are more than 2 folders on a CD.
ENTER / LIST
• Confirms the settings.
• Checks tracks, files or preset stations.
1. Pull out the battery holder with a sharp product
like a ball point pen.
2. Put the battery with
battery holder.
and
correctly on the
3. Push the battery holder back into its original
position.
, Note
 Use only one CR2025 (3 V) lithium battery.
 Remove the battery if the remote control is
not used for a long period of time.
 Do not leave the product in a hot or humid
place.
 Do not handle the battery with metallic
tools.
 Do not store the battery with metallic
materials.
Getting Started
j RPT
Repeats playback.
8
Connecting
About detachable
control panel
[LCS710BR /
LCS710DAB]
2
Attaching the control panel
Detaching the control panel
1. Press the 6 to open the control panel.
2. Push the control panel to right.
Connecting
3. Pull the control panel out of the unit.
4. Put the detached control panel into the
protective case.
1. Align the left side of the panel with the stopper.
2. Push the right side of panel into the unit until it
clicks.
> Caution
 The control buttons may not work properly
if the control panel is not attached properly.
If this occurs, gently press the display.
 Do not leave the control panel in any area
exposed to high temperatures or direct
sunlight.
 Do not drop the control panel or otherwise
subject it to strong impact.
 Do not allow such volatile agents as
benzine, thinner, or insecticides to come
into contact with the surface of the control
panel.
Control panel
Protective Case
, Note
Periodically wipe the contacts on the back
of the control panel with a cotton swap
moistened with alcohol. For safety, turn off the
ignition before cleaning, and remove the key
from the ignition switch.
Connecting
About detachable
control panel
[LCF810BR /
LCF810DAB]
Attaching the control panel
Detaching the control panel
1. Press the OPEN to open the control panel.
2. Push the control panel to left.
3. Pull the control panel out of the unit.
h
2. Attach part C of the control panel to part D
of the unit while pushing the control panel to
left.
4. Put the detached control panel into the
protective case.
3. Close the control panel.
k
j
Control panel
Protective Case
, Note
> Caution
 The control buttons may not work properly
if the control panel is not attached properly.
If this occurs, gently press the display.
 Do not leave the control panel in any area
exposed to high temperatures or direct
sunlight.
 Do not drop the control panel or otherwise
subject it to strong impact.
 Do not allow such volatile agents as
benzine, thinner, or insecticides to come
into contact with the surface of the control
panel.
2
Connecting
1. Attach part CA of the control panel to part CB
of the unit.
i
9
Periodically wipe the contacts on the back
of the control panel with a cotton swap
moistened with alcohol. For safety, turn off the
ignition before cleaning, and remove the key
from the ignition switch.
10
Connecting
Installation
ISO-DIN Installation
Basic Installation
Before installing, make sure that the ignition-switch
is set to OFF and remove the terminal of the car
battery to avoid short-circuiting.
2
Connecting
Bend the claws
according to
the thickness
of the
dashboard.
Control panel
1. Slide the unit into the ISO-DIN frame.
2. Fit screws removed from the old unit.
3. Slide the unit and frame into the dash opening.
4. Install the dash panel or adapter plate.
Control panel
1. Remove the existing receiver unit.
2. Make the necessary connections.
3. Install the installation sleeve.
4. Install the unit into the installation sleeve.
Removing the existing receiver
unit
If there is already an installation sleeve for the
receiver unit in the dashboard, it must be removed.
1. Remove the rear support from the unit.
2. Remove the control panel and trim ring from
the unit.
3. Insert the lever into the hole on one side of the
unit. Perform the same operation on the other
side and pull the unit out from the mounting
sleeve.
(According to models, this step may not be
needed.)
5. Install the trim ring to the unit.
6. Install the control panel to the unit.
Connecting
11
Connection
Connecting to a car
Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery
to avoid short-circuiting.
To Audio in
To Audio out
Sub-woofer Left
ab c d ab c d
ef g h ef g h
Sub-woofer Right
Front Left
Front Right
Rear Left
Rear Right
Power
Antenna
Sub-woofer
Amplifier
SMB type of DAB Antenna can be connected.
(Only LCS710DAB / LCF810DAB)
Control Relay
B f Power Antenna (Blue)
B g Dimmer (Pink)
Dimmer Switch
B c To Ignition (Red)
Ignition Switch
a
b
A
c
A
d
A
e
A
f
A
g
A
h
B h Ground (-) (Black)
B e Remote On
(Blue / White)
A
A
B d To Battery (+) (Yellow)
Amplifier
A a Gray : Front Right +
A b Gray / Black Stripe: Front Right A c Violet : Rear Right +
B b Phone Mute
(Orange)
A d Violet / Black Stripe: Rear Right A e White : Front Left +
A f White / Black Stripe: Front Left -
B a Not connected
A g Green : Rear Left +
A h Green / Black Stripe: Rear Left -
2
Connecting
Wired remote input (Black): Hard-wired control adapter can be connected.
(Optional)
Wired mic (Optional)
12
Operating
Operation
Checking the clock
1. Press DISP to check the clock.
2. Press it again to remove it.
Basic operations
1. Turn the unit on by pressing any key on the
unit.
Turning off the display light
2. Select a source by pressing SRC.
2. Press and hold it again to turn it on.
3. Rotate the volume knob to adjust the volume
on the unit.
Or press VOLUME W / S on the remote control.
, Note
If a source is not connected to the unit, the
source is not recognized.
Turning off the sound
temporarily
3
1. Press and hold DISP.
, Note
Under the light-off condition, press any
key, the light is turned on and then off
automatically if you don't press it within a few
seconds.
Resetting the unit
You can reset the unit when it does not operate
properly.
Operating
1. Press
to mute your unit. (Except CD, USB
device and SD card)
Or press MUTE on the remote control.
1. Detach the control panel.
2. To cancel it, press again.
Or press MUTE again.
2. Press the RESET hole with a sharp object.
Refer to page 8 to 9 for detaching the control
panel.
Using EQ (Equalizer)
EQ is to increase or decrease the signal strength of
audio frequencies. The function helps you to enjoy
sound more plentifully.
Press EQ on the unit. And rotate the volume knob
to select the item and press it. The indicator lights
up in the following order.
FLAT / XDSS+ / POP / CLASSIC / ROCK /
JAZZ / VOCAL / SALSA / SAMBA / REGGAE
/ RUSSY / USER EQ1 / USER EQ2
, Note
You can adjust sound level to your preference.
Once you select a USER EQ1 / 2 mode and
press and hold ` on the unit, then adjust the
sound level ((BAS (bass), MID (middle), TRB
(treble), BALANCE (left / right speaker), FADER
(front / rear speaker), SW (Subwoofer), SW-F
(Subwoofer Frequency), A-EQ (Auto EQ)), it
will be automatically stored for the currently
selected USER EQ1 / 2 mode. Refer to the "For
[SOUND] setting" for USER EQ1 / 2 mode on
the page 13.
[LCS710BR / LCS710DAB]
[LCF810BR / LCF810DAB]
Operating
13
Adjusting the general settings
For [SOUND] setting
You can adjust [SOUND], [LIGHT] and [OTHER]
settings.
You can adjust sound quality by adjusting the level
of BALANCE (left / right speaker), FADER (front /
rear speaker), SW (Subwoofer), SW-F (Subwoofer
Frequency) and A-EQ (Auto EQ).
On the unit
1. Press and hold `.
2. Rotate the volume knob to select [SOUND],
[LIGHT], or [OTHER] and press it.
3. Rotate the volume knob to select the item and
press it.
4. Rotate the volume knob clockwise or
counterclockwise to adjust the level.
5. Press the volume knob to confirm the setting.
If you want to return to the previous step, press
.
- When you set the EQ to USER EQ1 / 2 mode. :
You can adjust the sound level of BAS (bass), MID
(middle), TRB (treble), BALANCE (left / right speaker),
FADER (front / rear speaker), SW (Subwoofer), SW-F
(Subwoofer Frequency) and A-EQ (Auto EQ)
 SW (Subwoofer)
You can adjust the volume of subwoofer.
 SW-F (Subwoofer Frequency)
You can enable the subwoofer.
SW OFF <-> SW 55 Hz <-> SW 85 Hz <-> SW 120
Hz.
3. Press w / s to select the mode and press
ENTER.
For [LIGHT] setting
4. Press w / s to adjust the level.
You can adjust the light effects by adjusting LED,
DIM, or DIM L.
1. Press and hold FUNC / • MENU.
5. Press ENTER to confirm the setting.
If you want to return to the previous step, press
.
 LED COL1 / COL2 / AUTO : You can change the
LED window color.
 DIM (Dimmer) OFF / ON / AUTO : You can change
the brightness of the display window during the
power-on status.
Settings
Description
DIM ON
The display window
becomes dark.
DIM OFF
The display window
becomes bright.
DIM AUTO
The dimmer operates
according to the car
dimmer setting.
 DIM L (Dimmer Level) : When you set DIM to ON
/ AUTO, you can adjust the dimmer level. (-2, -1,
0, +1, +2)
3
Operating
2. Press w / s to select [SOUND], [LIGHT], or
[OTHER] and press ENTER.
 A-EQ (Auto EQ) ON / OFF
AUTO EQ operates only in the music file
supported with genre in the device. When you
set AUTO EQ to ON, POP, CLASSIC, ROCK, or JAZZ
is automatically selected according to the music
genre.
On the Remote Control
14
Operating
For [OTHER] setting
 AUX (Auxiliary) ON / OFF
It is possible to use auxiliary equipment with this
unit. Activate the auxiliary setting when using
auxiliary equipment connected to this unit.
[LCS710BR / LCS710DAB]
1. Insert a CD.
 DEMO OFF / ON
You can change the initial indication on the
display to information name (function name, EQ
name, etc...) while listening to a source.
2. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W / S on the remote control.
 BEEP 2ND / ALL
BEEP 2ND : The beep is generated when a key is
pressed for longer than 2 seconds.
BEEP ALL : The beep is generated when any key
is pressed.
1. Press the OPEN to open the control panel.
 CLK (Clock)
For the model RDS is not supported unit or even
for a RDS supported unit.
3
Listening to a CD
[LCF810BR / LCF810DAB]
2. Insert a CD.
3. Close the control panel.
4. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W / S on the remote control.
- When RDS CT information is not received and
then you set CT to OFF, you can adjust the
time by yourelf. Set the clock as follows ;
Operating
1. Select a source to TUNER.
2. Press the F to select the CT and then set
CT to OFF.
(Refer to the " Adjusting TUNER settings " on
the page 18 for setting the CT (Clock Time)
ON / OFF.)
3. Press and hold ` on the unit to select
[OTHER] and then select CLK by rotating the
volume knob.
, Note
Make sure to press B after pressing OPEN to
eject a disc. Refer to the picture above.
Pausing or restarting CD
playback
4. Set the hour by rotating the volume knob.
1. Press N on the unit to pause playback.
Or press d/M on the remote control.
5. Press the volume knob to confirm the hour.
2. Press it to resume playback.
6. Set the minute by rotating the volume knob.
7. Press the volume knob to confirm the
minute.
- When RDS CT information is received ;
The clock is displayed according to the RDS CT
information.
- When RDS is not supported, set the clock
according to 3 to 7 steps.
Searching for a section within
a track / file
1. Press and hold A / D on the unit for about 1
second during playback.
Or press and hold c / v on remote control.
2. Press N on the unit at the point you want.
Or press d/M on the remote control.
Operating
Skipping to another track/ file
On the Remote Control
Press A / D on the unit.
Or press c / v on the remote control.
1. Press FUNC / • MENU.
Or
1. Press the volume knob on the unit.
Or press ENTER on the remote control.
2. Rotate the volume knob on the unit to select a
desired ROOT or folder and press it.
Or press w / s and press ENTER on the remote
control.
3. Rotate the volume knob on the unit to select a
desired track / file and press it.
Or press w / s and press ENTER on the remote
control.
, Note
To skip to previous track, press briefly A within 3 seconds of playing time.
MP3 / WMA files often come with tags. The tag
gives the Title, Artist or Album.
Press DISP repeatedly during MP3 / WMA / CD TEXT
file playback. If there is no information, "NO TEXT"
will be shown in the display window.
Playing back tracks / files in a
way you want
For using applicable buttons
1. Press INT / RPT / SHF.
2. Press it again to cancel.
Or
Using the FUNC button
On the unit
1. Press F .
2. Rotate the volume knob to select an item and
press it.
3. Rotate the volume knob to select the option.
4. Press the volume knob to set the option.
If you want to return to the previous step, press
.
2. Press w / s to select an item and press it.
3. Press w / s to select the option.
4. Press ENTER to set the option.
If you want to return to the previous step, press
.
 RPT (Repeat)
The current selected tracks / files (1 RPT) or folder
RPT) on the disc is played repeatedly.
(
 SHF (Shuffle)
Each files in the current selected folder
SHF) or all of the tracks / files (SHF) on
(
the disc is played randomly. During random
playback, even if you press A, you won't go back
to the previous track.
 INT (Intro Scan)
The first 10 seconds of all tracks / files (INT) or
each files in the current selected folder (
INT)
on the disc are played.
 DEV (Device) USB / SD
You can change the recording device.
USB <-> SD
 MODE
SPD REC / SPD COPY
SPD REC : The recording speed is normal. And
during the recording, you can listen to the music
being recorded.
SPD COPY : The recording speed is twice as fast.
And during the recording, you can listen to the
TUNER / DAB. But you cannot listen to the music
being recorded.
, Note
DEV and MODE are only available when the
disc is activating.
3
Operating
Checking information about
your music
15
16

Operating
, Note
: The icon is displayed during MP3 / WMA
playback.
 MP3 / WMA Disc compatibility with this
unit is limited as follows:
1. Sampling Frequency / 8 kHz to 48 kHz
(MP3) 22.05 kHz to 48 kHz (WMA).
2. Bit rate / within 8 kbps to 320 kbps (include
VBR) (MP3) 32 kbps to 320 kbps (WMA).
3. CD-R / CD-RW file system should be "ISO
9660".
4. If you record MP3 / WMA files using
software which cannot create a FILE
SYSTEM, for example "Direct-CD" etc., it will
not be possible to playback MP3 / WMA
files. We recommend that you use "EasyCD Creator" which creates an ISO 9660 file
system.
3
Operating
You have to set the disc format option
to [Mastered] in order to make the discs
compatible with the LG players when
formatting rewritable discs. When setting the
option to Live File System, you cannot use it
on LG players.
(Mastered / Live File System : Disc format
system for Windows Vista)
Customers should also note that
permission is required in order to
download MP3 / WMA files and music from
the Internet. Our company has no right to
grant such permission. Permission should
always be sought from the copyright
owner.
Listening to music
from an external
device
1. Connect an external device to the AUX jack with
line input cable.
2. Select a source to AUX.
3. Play the connected Auxiliary Equipment.
4. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W / S on the remote control.
Preventing radical changes in
volume as switching sources
Only when you set AUX to ON as switching sources,
you can adjust the volume level of each source to
prevent radical changes in volume by selecting
GAIN 0 / +3 / +6.
1. Press F on the unit.
Or press FUNC / • MENU on the remote control.
2. Rotate the volume knob on the unit.
Or press w / s on the remote control to set the
option. (GAIN 0 / +3 / +6)
3. Press the volume knob on the unit.
Or press ENTER on the remote control to
confirm the setting.
4. If you want to return to the previous step, press
.
on the remote control.
Or press
Operating
Listening to the
TUNER
1. Press SRC repeatedly to select a source to
TUNER.
2. Press BAND repeatedly to select a desired band.
3. For manual search, press and hold A / D on
the unit until “MANUAL“ is displayed. Then press
it repeatedly to select a desired frequency.
Or press and hold c / v on the remote
control.
For auto search, press A / D on the unit until
“SEARCH” is displayed. (Except MW)
Or press c / v on the remote control.
4. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W / S on the remote control.
1. Press BAND to select a desired band you want
to store.
2. Select the desired frequency by using A / D on
the unit.
Or use c / v on the remote control.
3. Press the volume knob and rotate the volume
knob to select a preset station among 1 to 6
and then press and hold the volume knob until
the beep sound is heard.
Or press ENTER and press w / s to select a
preset station among 1 to 6 and then press and
hold ENTER until the beep sound is heard on
the remote control.
Or press and hold one of preset buttons among
1 to 6 on the remote control until the beep
sound is heard.
Or press and hold one of preset buttons among
1 to 6 on the unit until the beep sound is heard.
(Only LCS710BR / LCS710DAB)
4. Repeat steps 1 to 3 to preset other stations.
, Note
When a station is stored on the preset
numbers on which another station of the same
band has already been preset, the previously
preset station is automatically erased.
Listening to a preset station
1. Press BAND repeatedly to select a desired band.
2. Press the volume knob on the unit.
Or press ENTER on the remote control.
3. Rotate the volume knob to select a preset
station.
Or press w / s on the remote control.
4. Press the volume knob.
Or press ENTER on the remote control.
Or
Press BAND and then press the desired preset
button among 1 to 6 on the remote control.
Or press BAND and then press the desired preset
button among 1 to 6 on the unit. (Only LCS710BR /
LCS710DAB)
3
Operating
Storing desired frequencies
manually
17
18
Operating
Adjusting TUNER settings
On the unit
1. Press F .
2. Rotate the volume knob to select an item and
press it.
3. Rotate the volume knob to set the option and
press it.
4. If you want to return to the previous step, press
.
On the Remote Control
1. Press FUNC / • MENU.
2. Press w / s to select an item and press ENTER.
3. Press w / s to set the option and press ENTER.
4. If you want to return to the previous step, press
.
3
Operating
 PTY (Program type, RDS (OPTIONAL))
It searches the radio stations by program type of
FM tuner.
The program types are displayed as follows.
NEWS
FINANCE
EASY M
AFFAIRS
CHILDREN
LIGHT M
INFO
SOCIAL
CLASSICS
SPORT
RELIGION
OTHER M
EDUCATE
PHONE IN
JAZZ
DRAMA
TRAVEL
COUNTRY
CULTURE
LEISURE
NATION M
SCIENCE
DOCUMENT
OLDIES
VARIED
POP M
FOLK M
WEATHER
ROCK M
 A / S (Auto Store)
The six strongest broadcasting frequencies will
be stored under preset button 1 to 6 in the order
of their signal strength. To cancel, press the
volume knob (or ENTER on the remote control).
 P / S (Preset scan)
Each preset station appears. To cancel, press the
volume knob (or ENTER on the remote control).
 SENS (Tuner sensitivity) MID / HI / LOW
In an area in which signal reception is weak, it
helps the tuner to search more stations. The
weaker the reception is, the lower option you
should set to.
RDS (OPTIONAL)
 AF (Alternative Frequency) ON / OFF
When the reception quality drops, the tuner
automatically changes to another station in the
network, broadcasting a better reception quality,
using the PI and AF codes.
 REG (Region) ON / OFF
REG ON : The unit switches to another station,
within the same network, broadcasting the same
program when the receiving signals from the
current station become weak.
REG OFF : The unit switches to another station,
within the same network when the receiving
signals from the current station become weak.
(In this mode, the program may differ from the
one currently received.)
 TA (Traffic Announcement) ALARM / SEEK
TA ALARM : When the tuned station has no TP
information for 5 seconds, a double beep sound
is output.
TA SEEK : When the tuned station does not
receive TP information for 5 seconds, the receiver
retunes to the next station that has the TP
information.
 PI (Programme Identification) SOUND / MUTE
PI SOUND : When the frequency of a tuned
station switches to an AF (Alternative frequency)
with an unidentified PI, it keeps the sound.
PI MUTE : When the frequency of a tuned station
switches to an AF with an unidentified PI, it
mutes the sound until the PI is identified.
 CT (Clock Time) ON / OFF
You can use the RDS CT information to update
the time. When RDS CT information is not
received and then you set CT to OFF, you can
adjust the time by yourself. Refer to the page 14
for setting the clock.
Operating
Listening to the DAB
(Only LCS710DAB /
LCF810DAB)
19
4. Repeat steps 1 to 3 to preset other stations.
, Note
When a station is stored on the preset
numbers on which another station of the same
band has already been preset, the previously
preset station is automatically erased.
1. Press SRC repeatedly to select a source to DAB.
2. Press BAND repeatedly to select a desired band.
3. Press the volume knob on the unit.
Or press ENTER on the remote control.
Listening to a preset station
1. Press BAND repeatedly to select a desired band.
4. Rotate the volume knob to select a station.
Or press w / s on the remote control.
2. Press and hold the volume knob on the unit.
Or press ENTER on the remote control.
5. Press the volume knob.
Or press ENTER on the remote control.
3. Rotate the volume knob to select a preset
station.
Or press w / s on the remote control.
6. Press A / D on the unit to skip to another
station.
Or press c / v on the remote control.
7. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W / S on the remote control.
Or
Press BAND and then press the desired preset
button among 1 to 6 on the remote control.
Or press BAND and then press the desired preset
button among 1 to 6 on the unit. (Only LCS710DAB)
Adjusting DAB settings
Storing desired frequencies
manually
On the unit
1. Press BAND to select a desired band you want
to store.
2. Rotate the volume knob to select an item and
press it.
2. Select the desired frequency by using A / D on
the unit.
Or use c / v on the remote control.
3. Rotate the volume knob to set the option and
press it.
3. Press and hold the volume knob and rotate the
volume knob to select a preset station among 1
to 6 and then press and hold the volume knob
until the beep sound is heard.
Or press and hold ENTER and press w / s to
select a preset station among 1 to 6 and then
press and hold the ENTER until the beep sound
is heard on the remote control.
Or press and hold one of preset buttons among
1 to 6 on the remote control until the beep
sound is heard.
Or press and hold one of preset buttons among
1 to 6 on the unit until the beep sound is heard.
(Only LCS710DAB)
1. Press F .
4. If you want to return to the previous step, press
.
On the Remote Control
1. Press FUNC / • MENU.
2. Press w / s to select an item and press ENTER.
3. Press w / s to set the option and press ENTER.
4. If you want to return to the previous step, press
.
3
Operating
For auto search, press and hold A / D on
the unit until “ENS SRCH” (Ensemble Search) is
displayed.
Or press and hold c / v on the remote
control.
4. Press the volume knob.
Or press ENTER on the remote control.
20 Operating
 PTY (Program type, RDS (OPTIONAL))
The program types are displayed as follows.
When you select an item, it will start operating
immediately.
Using an USB device /
SD card
NEWS
FINANCE
EASY M
[USB]
AFFAIRS
CHILDREN
LIGHT M
1. Open the USB cover.
INFO
SOCIAL
CLASSICS
2. Connect the USB device.
SPORT
RELIGION
OTHER M
3. Press SRC repeatedly to select a source to USB.
EDUCATE
PHONE IN
JAZZ
DRAMA
TRAVEL
COUNTRY
CULTURE
LEISURE
NATION M
SCIENCE
DOCUMENT
OLDIES
VARIED
POP M
FOLK M
WEATHER
ROCK M
4. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W / S on the remote control.
[SD]
1. Detach the control panel. (Refer to "About
detachable control panel" on page 8 to 9.)
2. Connect the SD card.
3. Attach the control panel.
3
Operating
 A-SCAN (Auto Scan)
Scans all available services. To confirm the lists,
press the volume knob and rotate the volume
knob.
 P-SCAN (Preset Scan)
The broadcasting frequencies stored in the
preset number are received Sequentially.
Each broadcasting frequencies are received for 6
seconds.
4. Press SRC repeatedly to select a source to SD.
5. Rotate the volume knob on the unit to adjust
the volume.
Or press VOLUME W / S on the remote control.
 DRC (Dynamic Range Control) ON / OFF
Automatically adjusts the audio level.
 ANNOUNCE (Announcement) X / O
Provides information on selected contents.
TRFC (Traffic), TRNSP (Transport), WARN (Service
Warning), NEWS, WTHR (Weather), EVNT (Event),
SEVNT (Special Event), PINFO (Program Info),
SPORT (Sport Report), FNNC (Financial Report)
 LINK
DAB+FM / OFF / DAB / FM
When the reception quality drops, the tuner
automatically changes to another station in the
network.
If the broadcasting is disconnected during
operation, it does not sound until the next
broadcasting is linked. It takes about 10 seconds.
Depending on the amount of broadcasting
information, it can be shorter or longer.
, Note
If each preset number has no stored frequency,
"EMPTY" is displayed.
[LCS710BR / LCS710DAB]
[LCF810BR / LCF810DAB]
Moving to another drive
When connecting this unit to multi-reader, press
BAND on the unit (or DRV on remote control) to go
the next drive. Each time you press the button, the
driver modes change.
Operating
Quick Search of a desired file
You can select and play a desired file regardless of
the order in USB device / SD card.
1. Press the volume knob on the unit.
Or press ENTER on the remote control.
2. Rotate the volume knob on the unit to select a
desired ROOT or folder and press it.
Or press w / s and press ENTER on the remote
control.
3. Rotate the volume knob on the unit to select a
desired track / file and press it.
Or press w / s and press ENTER on the remote
control.
Deleting the desired file
You can select and delete a playable file you want.
1. Select the desired file in the same way as "Quick
Search of a desired file"
When the delete operation is started, playing is
stopped. When the delete operation is ended, the
list of files is displayed. If you do not select a file
within few seconds, or press the
, the first file is
played.
, Note
Other functions are same with "Listening to a
CD". Refer to page 14 to 15.
Playable USB device / SD card
Requirement
 Do not extract the USB device / SD card during
operation (play, etc.).
 An USB device / SD card which requires
additional programme installation when
you have connected it to a computer, is not
supported.
 Regular back up is recommended to prevent
data loss.
 If you use a USB extension cable, USB HUB, USB
Multi-reader, or external HDD, the USB device
may not be recognized.
 When you connect a partitioned USB device into
the unit, only the first partition is recognized on it.
 Some USB device may not work with this unit.
 Digital camera and mobile phone are not
supported.
 USB Port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
 Using FAT (16 / 32) file system is supported.
Using NTFS file system is supported to read only.
Recording to USB device / SD
card
[USB]
1. Open the USB cover and connect it to the unit.
2. Select one of the following lists. (CD, FM tuner,
DAB(Only LCS710DAB / LCF810DAB), Bluetooth
Handsfree)
3. Press R to start recording.
For one track CD recoridng, press it once.
For all tracks recording, press and hold it until
the beep is heared. (In case of MP3 / WMA CD,
recorded all files in the folder.)
4. Press it again to stop.
[SD]
1. Detach the control panel and connect it to the
unit. Then attach the control panel.
(Refer to "About detachable control panel" on
page 8 to 9.)
2. Select CD only.
3. Press R to start recording.
For one track CD recoridng, press it once.
For all tracks recording, press and hold it until
the beep is heared. (In case of MP3 / WMA CD,
recorded all files in the folder.)
4. Press it again to stop.
3
Operating
2. Press R , and then "DELETE?" displayed. Press it
again to delete.
21
22 Operating
, Note
 [USB] Only in CD, FM tuner, DAB and
Bluetooth Handsfree, recording is available.
[SD] Only in CD, recording is available.
 Do not remove the USB device / SD card
during recording, or an incomplete file may
be made and not deleted on PC.
 When USB device / SD card is not
connected, "REC ERR NO USB" / "REC ERR
NO SD" displays and cannot record.
Listening to music
by connecting iPod /
iPhone
You can enjoy iPod / iPhone-stored music on the
unit by connecting it to the USB connector using
the appropriate cable.
 When USB device / SD card memory is full,
"MEMORY FULL" [LCS710BR / LCS710DAB]
"REC ERR MEMORY FULL" [LCF810BR /
LCF810DAB] displays and stops recording.
 While FM tuner / DAB / Bluetooth Handsfree
recording, the broadcastings are recorded
as a file every 20 minutes.
3
 While one track CD recording, "REC 1"
appears. While other recording, "REC"
appears.
Operating
 You can adjust the recording speed.
(Refer to the page 15.)
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
[LCS710BR / LCS710DAB]
[LCF810BR / LCF810DAB]
1. Open the USB cover.
2. Connect the iPod / iPhone.
3. Press SRC to select a source to USB.
4. Rotate the volume knob to adjust the volume
on the unit.
Or press VOLUME W / S on the remote control.
, Note
Refer to the page 23 to check the compatible
iPod model for this unit.
Pausing or restarting playback
1. Press N on the unit to pause playback.
Or press d/M on the remote control.
2. Press it to resume playback.
Searching for a section within
a track / file
During playback, press and hold A / D and then
release at a point you want.
Checking information about
your music
MP3 / WMA files often come with tags. The tag
gives the Title, Artist or Album.
Press DISP repeatedly during MP3 / WMA file
playback. If there is no information, "NO TEXT" will
be shown in the display window.
Operating 23
Playing back tracks / files in a
way you want
Playing back files by music
menus
On the Unit
You can check files by music menus and play it
back.
The music menus are as follows.
1. Press F .
2. Rotate the volume knob to select an item and
press it.
3. Rotate the volume knob to select the option.
4. Press the volume knob to set the option.
If you want to return to the previous step, press
.
On the Remote Control
1. Press RPT / SHF.
2. Press it again to cancel.
Or
1. Press FUNC / • MENU.
2. Press w / s to select an item and press ENTER.
4. Press ENTER to set the option.
If you want to return to the previous step, press
.
 RPT (Repeat)
The current selected tracks / files (1 RPT) or
RPT) on the iPod / iPhone is played
folder (
repeatedly.
 SHF (Shuffle)
Each file in the currently selected album
SHF) or all of the tracks / files (SHF) on the
(
iPod / iPhone are played randomly.
During random playback, even if you press A,
you won't go back to the previous track.
 SPD (BOOK SPEED)
You can adjust the audiobook speed of iPod /
iPhone to NOR (Normal), FAST or SLOW.
1. Press the volume knob on the unit.
Or press ENTER on the remote control.
2. Rotate the volume knob on the unit to select a
music menu and press it.
Or press w / s on the remote control.
3. Rotate the volume knob on the unit to select a
file.
Or press w / s on the remote control.
4. Press the volume knob on the unit to confirm
the setting.
Or press ENTER on the remote control.
5. If you want to return to the previous step, press
.
Or press
on the remote control.
2WAY Control
You can control on the unit and iPod / iPhone.
 Press iPOD / • TA on the unit. Then playback is
paused. And you can control on the unit and
iPod / iPhone.
 While using the 2WAY Control, any functions are
not available on the unit.
 Press iPOD / • TA again to cancel the 2WAY
Control.
Compatible iPod models
iPod classic (5th / 6th generation)
iPod nano (1st / 2nd / 3rd / 4th / 5th generation)
iPod touch (1st / 2nd / 3rd generation)
iPhone
iPhone 3G
iPhone 3GS
iPhone 4
We recommend that you use the OS
Version 4.2.1 or more.
3
Operating
3. Press w / s to select the option.
PLAYLISTS / ARTISTS / ALBUMS / GENRES
/ SONGS / COMPOSER / AUDIO BOOK /
PODCAST / ...
24 Operating
Microphone (OPTIONAL)
 Unit has a built-in microphone.
“Made for iPod” means that an electronic accessory
has been designed to connect specifically to iPod
and has been certified by the developer to meet
Apple performance standards.
“Works with iPhone” means that an electronic
accessory has been designed to connect
specifically to iPhone and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
iPod is a trademark of Apple Inc., registered in the
U.S. and other countries.
iPhone is a trademark of Apple Inc.
[LCS710BR / LCS710DAB]
[LCF810BR / LCF810DAB]
 The microphone needs to be close to and
pointed toward the person speaking. Install the
microphone as shown below.
Microphone unit
3
Operating
Connecting a
Bluetooth wireless
technology
Before you start the pairing procedure, make sure
the Bluetooth wireless technology is turned on in
to your phone. Refer to your phone’s user guide.
Pairing links your unit and phone with Bluetooth
wireless technology, and is required only once for
the initial setup. If the connection is successful, the
phone is registered (Device 1 to 10). The process
of pairing may be different depend on the phones.
The PIN CODE is 1234.
ON PLAYER
1. Enter the menu.
2. Find the "CONNECT" menu.
Rotate the
volume knob
3. Enter the "CONNECT" menu.
Press the
volume knob
4. Select the "SEARCH" menu.
Rotate the
volume knob
5. Search the phones supported
Bluetooth wireless technology.
Press the
volume knob
6. Select a phone you want to
connect.
Rotate the
volume knob
7. Connect the phone.
Press the
volume knob
, Note
If you power off the unit while talking on
the phone through the unit by using the BT
function, the function is deactivated and you
can talk on the phone directly.
Operating 25
Using the buttons for
Bluetooth wireless technology
a
Using a Bluetooth wireless
technology
Disconnecting a phone
Go to the menu ( -> CONNECT -> LIST ->
Connected device name -> DISCONN).
Answering and Ending a call
When your unit rings, press
To end a call, press
to answer a call.
.
b
Rejecting a call
c
d
a Volume knob
• Press the volume knob : Go to the next
contents of the setting.
b
• Press it to enter BT function.
.
Making a call saved as a preset
number
Press
and a preset number (1 to 6).
Checking missed calls
When an incoming call is not answered, the missed
call message is displayed on the display window
(without headset profile). When the “ ? ” appears,
go to the menu ( -> CALL -> LASTCALL). You can
check the list of missed call.
• Answers a call.
c
Returns to the previous step.
Ends a call.
d A/D
Adjusts the mic volume while talking on the
phone by BT function.
• A : Press it to delete a spell or go back
previous contents.
• D : When you write some words on the unit,
press it to move next space on display.
, Note
 The lists of LASTCALL are sorted from
newest to oldest entries.
 When you want to make an international
call, press D to add “+” and to delete it press
again.
 “+” can only be added when the detail list of
LASTCALL is selected.
 Rejecting a call / Making a call saved preset
number / Missed call notification
(These features are only available on phones
with Handsfree profile.)
 You can record the Bluetooth Handsfree to
USB. (Refer to the page 21 to 22.)
3
Operating
• Rotate the volume knob : Move the contents
vertically on the setting or choose a spell when
you write the words on the unit.
When your unit rings, press
26 Operating
Audio transfer
Adjusting the setting
It is possible to switch the audio connection
between your phone equipped with Bluetooth
wireless technology and this unit.
1. Press
1. Press
to answer the call.
2. Press
again. The “PRIVATE” is displayed.
If the private mode is selected on the unit, press
to return to the call to hands-free mode.
Paring your unit and device with
Bluetooth wireless technology (MP3
Player, MP3 Phone...)
When you activate your Bluetooth device’s linked
unit, you can listen to MP3 with wireless connections.
The method of use for a Bluetooth device is the
same as when using a Bluetooth phone. Refer to the
phone’s user guide for using this function.
3
Playing MP3 files
Operating
When you turn Bluetooth on, your device supported
Bluetooth wireless technology displays “Bluetooth”
on the home screen. The Bluetooth remains on
until you turn the device off. Press SRC repeatedly
to select “BT”. To play an MP3 file stored on your
device. Refer to the phone’s user guide for using this
function. This feature is only available on phones
with A2DP(Advanced Audio Distribution Profile).
Bluetooth wireless technology
profiles information
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles.
This unit is compatible with following profiles.
GAP (Generic Access Profile)
HFP (Hands Free Profile)
GAVDP (Generic Audio / Video Distribution Profile)
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio / Video Distribution Remote Control
Profile)
PBA / PBAP (Phone Book Access Profile)
.
2. Rotate the volume knob to select an item and
press it.
3. Rotate the volume knob to set the option and
press it.
4. If you want to return to the previous step, press
.
CALL
 LASTCALL
Phone number list (Received, Dialed, Missed).
CALL -> LASTCALL -> Select the phone number
-> Press the volume knob -> Display the
information -> Press the volume knob -> DIAL,
SAVE, DELETE menu will be displayed.
- To call the phone number, DIAL -> Press the
volume knob.
- To save the phone number, SAVE -> Press the
volume knob -> select the preset number (1 to
6) -> Press the volume knob.
- To delete the selected phone number, DELETE ->
Press the volume knob -> NAME -> Press the
volume knob.
- To delete all phone number, DELETE -> Press the
volume knob -> ALL -> Press the volume knob.
 DIAL
Enters the number directly on the unit. To select
the 0 to 9 rotate the volume. Press D to make
the phone number. To call it, Press the volume
knob.
 PRESET
Checks and deletes/dials the phone number saved
preset number.
CALL -> PRESET -> Select the preset number and
press the volume knob -> Display the information
-> Press the volume knob -> DIAL, DELETE menu
will be displayed.
- To call the phone number, select DIAL and Press
the volume knob.
- To delete the selected phone number, DELETE ->
NAME -> Press the volume knob.
- To delete all phone number, DELETE -> ALL ->
Press the volume knob.
Operating 27
P-BOOK
 LIST
Checks the list of the phone numbers saved by
phonebook.
 SEARCH
Searches the phone number in the list.
WICS (Wireless Controller &
Synchronization)
You can control the unit by using the "WICS"
application.
1. Search the “WICS” application and install it.
 GET
Getting the phonebook from the phone
automatically. This menu is only available on phones
with PBA / PBAP (Phone Book Access Profile).
CONNECT
 LIST
Checks the list of the Connected Device Name.
 SEARCH
Searches the phones available to connect. The
Connected Device Name is displayed on the top.
[Displays installed "WICS" application]
SETUP
 AUTO CON
Adjusts connection with automatically or not.
(ON <-> OFF)
 AUTO ANS
Adjusts answering automatically or not.
(MANUAL <-> AUTO)
 MIC VOL
Adjusts microphone volume on the phone
from 1 to 5. While you are on the phone with
Bluetooth wireless technology, press A / D (or
c / v on the remote control) to adjust the
MIC volume.
 REDIAL
Adjusts the counts of redial. (1 TIME <-> 2 TIMES)
INFO
[Initial screen]
[Tuner screen]
- You can select a source by pressing "SOURCE".
 NAME
Changes the name of this unit.
 ADDRESS
Checks the address.
 PIN-CODE
Changes the PIN code. Default is 1234.
[Source Mode screen]
3
Operating
 VISIBLE
Makes it is impossible to search this unit.
(SHOWN <-> HIDDEN)
2. Pairing links your unit and iPhone with
Bluetooth wireless technology. (Refer to the
page 24.)
3. When you run the “WICS” application, activating
source is displayed after initial screen. Then you
can control the unit on iPhone.
28 Operating
Phone compatibility list
Bluetooth list and manufacturing
H : Hnadsfree
company applicable.
A : Audio Streming (A2DP)
Company
List
H
Nokia
E61
5200
N80
N70
N72
N91
3250
6110
6288
E90
N73
N95
N77
E71
E75
N97
5800 (Xpress
music)
C6
E5
E52
X6
N97-1
N900
6710 (Navigator)
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
3
Operating
Motorola
ROKR E6
V3x
RIZR K1
V9
Z8
V9r
XT701
XT720
(MOTOROI)
Milestone Droid
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
A
P
Company
List
H
A
P
SAMSUNG
D900
SGH-U600
SGH-Z240
SGH-F300
SGH-E890
SGH-E950
SGH-F210
SGH-G600
i-900
F330
F480
L878
M8800 PIXON
S5603
S8003 JET(8GB)
i8510 INNOV8 (16G)
i8910 Omnia HD
U808
B5722
B7330 (Omnia Pro)
B7620 (Giorgio
Armani)
C3303K
(Champ)
M5650U (Lindy)
M8910
(Pixon12)
S7350
S8500 (Wave)
i5503 (Galaxy 5)
i5700 (Galaxy
Spica)
i9000 (Galaxy
S(16G))
T959
Galaxy Tab
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
W880
Z610
W300
K800i
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
P : Phonebook Sync (GET)
O
O
SONY
ERICSSON
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Operating 29
Bluetooth list and manufacturing
H : Hnadsfree
company applicable.
A : Audio Streming (A2DP)
P : Phonebook Sync (GET)
Company
List
H
A
P
Company
List
H
A
P
SONY
ERICSSON
P990i
W910i
C702i
G705
W595
W705
W980i
Xperia-X1
Vizaz
Xperia-X2
Xperia-X10
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
LG
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
KE850
KU250
KU970
KS10
KC550
KC780
KC910(Renoir)
KF350(IceCream)
KF600
KF700
KF750(Secret)
KF900(PRADA2)
KM380
KM900(Arena)
KP500(Cookie)
KT520
KT610
KU990
GD900
BL40 (New Chocolate)
KM335
GD510 (POP)
GD880
GM730
GS500 (Cookie Plus)
GT505
GT540
GW305
GX500
Bold 9700
Storm2 9550
iphone
iphone 3GS
(16GB)
iphone 3GS
(32GB)
iPhone 4G
(16GB)
I-Pad
P750
Goole G1
Magic G2
Hero G3
Touch2
Legend
Nexus One
Desire
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
LG
APPLE
O
O
O
, Note
 When you switch the call mode from
handsfree to phone, the connection may be
disconnected.
 Some phones don’t support Reject function.
O
O
O
O
O
O
O
ASUS
HTC
O
O
O
O
3
Operating
O
O
O
O
O
O
O
O
O
O
O
O
 When the phone features <Bluetooth
Power Save> function, you should make the
function turned on to maintain connection.
 Low battery in phone may cause the
problems.
Rim
O
O
O
O
O
O
30 Operating
“The Bluetooth word mark and logos are owned by the Bluetooth SIG,
Inc. and any use of such marks by LG Electronics is under license. Other
trademarks and trade names are those of their respective owners.”
Bluetooth® wireless technology is a system which allows radio contact between electronic devices within a
max range of 10 meters.
Connecting individual devices under Bluetooth® wireless technology does not incur any charges. A mobile
phone with Bluetooth® wireless technology can be operated via the Cascade if the connection was made via
Bluetooth® wireless technology.
operating condition for using a Bluetooth wireless technology function
 Close windscreen.
 Turn off the air conditioner / heater.
 Stop the vehicle or drive at low speed.
 Make the call in a quiet location.
- There may be differences in call quality depending on phone type, road conditions weather, etc.
3
- Using the phone while driving may cause unexpected accidents.
Operating
- The Bluetooth wireless technology function may not operate properly with certain types of phones
equipped with Bluetooth wireless technology.
Troubleshooting
31
Troubleshooting
Cause
Solution
Power doesn't turned on.
Leads and connectors are not
properly.
Confirm once more that all connections
are correct.
The fuse is blown.
Rectify the problem that caused the fuse
to blow, and then replace it. Be very sure
to install the correct fuse with the same
rate.
Noise and other factors
are causing the built in
microprocessor to operate
incorrectly.
Turn the unit off and then on again.
No sound is heard.
Cables are not connected
correctly.
Connect the cables correctly.
There's audio skipping.
This unit is not firmly secured.
Secure this unit firmly.
The playback is not possible.
The disc is dirty.
Clean the disc.
The disc of unplayable type is
loaded.
Check what type the disc.
The signal strength of the
stations is too weak. (When
tuning in with automatic
tuning.)
Tuned in the stations manually.
No station has been preset
or preset stations have been
cleared. (When tuning by
scanning preset stations.)
Preset the stations.
(Refer to the page 17.)
iPod/ iPhone does not work.
Check whether iPod / iPhone
is connected to the unit
correctly.
Connect it to the unit correctly.
The unit does not operate
correctly even when the
appropriate remote control
buttons are pressed.
Battery power is low.
Load a new battery.
The unit doesn't operate.
Radio stations cannot be
tuned in.
4
Troubleshooting
Symptoms
32 Appendix
Specifications
USB
Version : USB 1.1 or USB 2.0 Full Speed
Bus Power Supply (USB) : DC 5 V
1A
General
Output Power : 53 W x 4 CH (Max.)
SD
Power Source : DC 12 V
Distortion : 0.1 %
Speaker impedance : 4 Ω
Ground System : Negative
Dimensions (W x H x D) : (178 x 50 x169) mm
(without Control Panel)
Frequency Response : 20 Hz to 20 kHz
Output Voltage : 2 V (Max.)
Net Weight : 1.37 kg
Subwoofer
TUNER
Frequency Response : 20 Hz to 120 Hz
FM Tuning Range :
Output Voltage : 2 V (Max.)
87.5 MHz to 108.0 MHz
S / N Ratio : 55 dB
Distortion : 0.7 %
Usable Sensitivity : 12 dBμV
 Design and specifications are subject to change
without notice.
AM (MW) Tuning Range :
(520 to 1720) kHz or (522 to 1620) kHz
S / N Ratio : 50 dB
Distortion : 1.0 %
Usable Sensitivity : 28 dBμV
DAB
Distortion : 0.1 %
Channel Separation (1 kHz) : 68 dB
5
Line OUT
CD
Appendix
Frequency Response : 20 Hz to 20 kHz
S / N Ratio : 80 dB
Distortion : 0.12 %
Channel Separation (1 kHz) : 55 dB
AUX
Frequency Response : 20 Hz to 20 kHz
S / N Ratio : 80 dB
Distortion : 0.1 %
Channel Separation (1 kHz) : 45 dB
Max Input Level (1 kHz) : 1.1 V
Download PDF