LG | LDF900UN | LG LDF900UN Owner’s Manual

OWNER’S MANUAL
CAR DVD Receiver
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LDF900UN
P/NO : MFL67244330
2
1
Safety Information
Safety Information
1
Safety Information
To reduce the risk of electric shock, do
not remove the cover or back of this
product. There are no user-serviceable
parts inside. Refer servicing to qualified
service personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
Always operate the vehicle in a safe
manner. Do not become distracted by
the vehicle while driving, and always
be fully aware of all driving condition.
Do not change settings, or any functions. Pull over
in a safe and legal manner before attempting such
operations.
Do not use for many hours at
extremely low or high temperature.
(-10 °C to 60 °C)
To reduce the risk of fire or electric
shock, do not expose this product to
dripping or splashing water, rain, or
moisture.
The temperature of unit’s outside can
be extremely high, please use the unit
after proper installation in your vehicle.
8 cm
This unit cannot play 8 cm disc (use 12
cm disc only).
While driving, keep the sound volume
at a proper level.
Do not drop it and avoid heavy
impacts at anytime.
The driver must not watch the monitor
while driving. If the driver watches the
monitor while driving, it may lead to
carelessness and cause an accident.
This unit is for vehicles with a 12volt battery and negative grounding.
Before installing it in a recreational
vehicle, lorry or bus, check the battery
voltage. To avoid shorts in the electrical system,
be sure to disconnect the E battery cable before
beginning the installation.
Safety Information
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service centre.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
“This device is equipped with a portable battery or
accumulator.
Safe way to remove the battery or the battery
from the equipment:
Remove the old battery or battery pack, follow the
steps in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do not
dispose of batteries or battery together with other
waste. It is recommended that you use local, free
reimbursement systems batteries and accumulators.”
The battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot
use it on LG players.
(Mastered/Live File System : Disc format system for
Windows Vista)
For ensuring safe driving
• To avoid the risk of accident and the potential
violation of applicable laws, this unit is not for use
with a video screen that is visible to the driver.
• This unit detects whether your car’s parking
brake is engaged or not, and prevents you from
watching a DVD,VCD, PHOTO or movie file on the
display connected to FRONT VIDEO OUTPUT while
driving. When you attempt to watch a DVD,VCD,
PHOTO or movie file the screen will turn black.
When you park your car in a safe place and apply
the parking brake, the picture appears on the
screen.
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it means
the product is covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products
shall be disposed of separately from the
municipal waste stream via designated
collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you
purchased the product.
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and
other relevant provisions of Directive
2006/95/EC and ECE Regulation 10.03
(3.2.9).
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere, The
Netherlands
(Tel : +31-(0)36-547-8888)
1
Safety Information
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
3
4
Contents
Contents
3
Installation
11
11
12
1
Safety Information
2
Safety Information
13
About detachable control panel
Attaching the control panel
Detaching the control panel
Basic Installation
13
Basic Installation
13
Removing the existing
receiver unit
14
ISO-DIN Installation
2
14
Remote Control Battery Installation
Preparation
15
Connection
6
Introduction
9
Front panel
10
Remote control
15
Connecting to a car
16
Connecting to optional
equipment
17
Adjusting the general settings
17
The buttons for setting
MENU
17
MENU item overview
18
XDSS+/EQ
18
Sound
19
Display
19
Light
20
Setup
Contents
4
5
Operation
Maintenance
21
Basic Operations
29
Notes on Discs
22
Other Operations
29
Handling the Unit
22
To display file information
22
To slow down the playing
speed
6
22
To play frame-by-frame
Troubleshooting
23
Quick search
23
Using the Func menu
24
Using the time search bar
24
Resume playback
7
25
Viewing a photo
Appendix
25
26
26
26
27
27
28
30
5
1
2
Troubleshooting
3
Listening to the radio
Storing desired frequencies
manually
Listening to a preset station
31
Area Code List
32
Specifications
33
Trademarks and Licences
4
Adjusting Tuner settings
Enjoying music or movie by
connecting an external device
5
Preventing radical changes
in volume as switching
sources
Recording to USB from Disc or FM
tuner
6
7
6
Preparation
2
Preparation
Reseting the unit
About the
1. Press
to open the control panel.
Refer to the page 12 for detaching the
control panel.

Preparation
Introduction
Symbol Display
“ ” may appear on your monitor display
during operation and indicates that the
function explained in this owner’s manual is
not available on that disc.

2
Symbol Used in this Manual
DVD
DVD-Video, DVD±R/RW in
Video mode or VR mode
and finalized
ACD
Audio CDs
MOVIE
Video files
MUSIC
Audio files
PHOTO
Photo files
You can reset the unit when it does not
operate properly.
2. Prick the reset hole with a sharp object.
Preparation
Playable USB device
Requirement
File compatibility
•
Do not extract the USB device during
operation (play, etc.).
•
Sampling frequency : within 8 kHz to 48 kHz
(MP3), below 48 kHz (WMA)
•
An USB device which requires additional
programme installation when you
have connected it to a computer, is not
supported.
•
Bit rate : within 8 kbps to 320 kbps (MP3),
below 320 kbps (WMA)
•
File extensions: “.mp3”, “.wma”, “.wav”, “.ogg”,
“.aac(less than 16 kHz)”
•
USB device: USB device that support USB
1.1 and USB 2.0 Full Speed.
•
Maximum files : Under 3000.
•
CD-ROM file format : ISO9660/ JOLIET.
•
Movie, music and photo files can be played.
For details of operations on each file, refer
to relevant pages.
•
We recommend that you use Easy-CD
Creator, which creates an ISO 9660 file
system.
•
Regular back up is recommended to
prevent data loss.
•
If you use a USB extension cable, USB HUB,
USB Multi-reader, or external HDD, the USB
device may not be recognized.
•
When you connect a partitioned USB
device into the unit, only the first partition
is recognized on it.
•
7
Audio files
•
Max pixel in width : 4000 x 4000 pixel.
•
Maximum files : Under 3000.
•
Some discs may not operate due to a
different recording format or the condition
of disc.
Some USB device may not work with this
unit.
•
File extensions: “.jpg”, “.jpeg”, “.png”, “.gif”, “.tiff ”,
“.bmp”
•
Digital camera and mobile phone are not
supported.
•
CD-ROM file format : ISO9660/ JOLIET.
•
USB Port of the unit cannot be connected
to PC. The unit cannot be used as a storage
device.
Video files
•
Available resolution size: 720 x 576 (W x H)
pixels
•
Frame rate: 30 FPS
•
Playable codec format: “MPEG1”, “MPEG2”,
“MPEG4”, “MP4V3S”, “3IVX” “MSVC”, “3IV0”,
“3IV1”, “3IV2”.
• This player supports only 1 warp point of Global
Motion Compensation (GMC).
Preparation
Photo files
2
8
Preparation
Playable Discs
DVD-VIDEO (12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD-R (12 cm disc)
DVD-RW (12 cm disc)
2
Preparation
DVD+R (12 cm disc)
Supports the double layer disc
also.
DVD+RW (12 cm disc)
Audio CD: Music CDs or CD-R/CDRW in music CD format that can
be purchased.
Some DVD±RW/DVD±R or CD-RW/CD-R cannot
be played on this unit due to the recording
quality or physical condition of the disc, or the
characteristics of the recording device and
authoring software.
Regional Codes
This unit has a regional code printed on the top
of the unit. This unit can play only DVD discs
labeled same as the top of the unit or “ALL”.
Copyrights
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyrighted
material without permission. This product features the
copy protection function developed by Rovi. Copy
protection signals are recorded on some discs. When
recording and playing the pictures of these discs
picture noise will appear. This product incorporates
copyright protection technology that is protected
by U.S. patents and other intellectual property
rights. Use of this copyright protection technology
must be authorized by Rovi, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Rovi. Reverse engineering or
disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS
TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL 525p
AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.
The making of unauthorized copies of
copy-protected material, including computer
programmes, files, broadcasts and sound
recordings, may be an infringement of copyrights
and constitute a criminal offense.
This equipment should not be used
for such purposes.
Be responsible
Respect copyrights
Preparation
9
Front panel
2
Preparation
a SRC/• OFF
• When pressed, selects function sources.
•
When pressed and held, powers unit on or
off.
b Returns to the previous step.
i USB port
j Displays file or disc information.
k MENU
Activates or deactivates a setting menu.
c Volume knob
l b[-/+[B
Skip / Search / Seek / Tune
• Adjusts volume level.
m Remote Sensor
• Confirms the settings.
n AUX
If connected to other portable player, you
can enjoy music or movie on the unit.
• Checks tracks or files.
d NX Plays and pauses playback.
e REC Recording to USB
f BAND
• Selects a band in Tuner mode.
•
Selects a category menu during playback of
a disc or USB containing with music, movie,
and photo files together.
NOTE
For video playback from an external device, you
should connect it with a 3.5 mm (4-pole) jack as
below.
g Display window
h Opens the front panel.
a Audio L
c GND
b Audio R
d Video
10
Preparation
Remote control
./> SKIP: Goes to the next or previous
chapter / track / file.
X : Pauses playback.
N : Starts playback or recording.
2
Preparation
x: Stops playback.
• • • • • • • • • c• • • • • • • • •
MENU: Activates or deactivates setting menu.
RETURN: Returns to the previous step.
Direction buttons: Selects an option in the
menu.
LIST/ ENTER :
•
Checks tracks or files in Disc mode or preset
stations in Tuner mode.
•
Confirms the settings.
DISPLAY: Displays or exits On-Screen Display.
DISC MENU/• TITLE:
• • • • • • • • • a • • • • • • • •
OFF: Powers off the unit.
SRC: Selects function sources.
MUTE: Temporarily stops the sound.
BAND :
•
When pressed, it accesses menu on a disc.
•
When pressed and held, it displays the DVD
title menu, if available.
• • • • • • • • • d • • • • • • • •
Numeric buttons (1 - 6)
Selects a numbered preset station in Tuner or a
chapter when a DVD disc is inserted.
•
Selects a band in Tuner mode.
VOL. +/- : Adjusts volume level.
•
Selects a category menu during playback of
a disc or USB containing with music, movie,
and photo files together.
REPEAT : Repeat playback
SHUFFLE : Random playback
INTRO: Intro scan
• • • • • • • • • b• • • • • • • • •
m/M SCAN: Searches backward or
forward.
AUDIO: Selects audio language or channel.
SUBTITLE: Selects a desired subtitle language.
ANGLE: Selects a DVD camera angle if
available.
Installation
11
3
Installation
About detachable
control panel
Attaching the control panel
3
Installation
You should attach the control panel after
unpacking the box to use the receiver unit.
And you can detach it according to your needs
and keep it in the protective case.
B
A
Attaching the control panel
1. Attach part A of the control panel to part
B of the unit.
D
C
2. Attach part C of the control panel to part
D of the unit while pushing the control
panel to left.
3. Close the control panel.
CAUTION
• The control buttons may not work properly if
the control panel is not attached properly. If this
occurs, gently press the display.
• Do not leave the control panel in any area
exposed to high temperatures or direct sunlight.
• Do not drop the control panel or otherwise
subject it to strong impact.
• Do not allow such volatile agents as benzine,
thinner, or insecticides to come into contact
with the surface of the control panel.
12
Installation
Detaching the control panel
NOTE
Detaching the control panel
3
Installation
1. Press
to open the control panel.
2. Push the control panel to left.
3. Pull the control panel out of the unit.
4. Put the detached control panel into the
protective case.
Periodically wipe the contacts on the back of the
control panel with a cotton swap moistened with
alcohol. For safety, turn off the ignition before
cleaning, and remove the key from the ignition
switch.
Installation
Basic Installation
13
Removing the existing receiver
unit
If there is already an installation sleeve for
the receiver unit in the dashboard, it must be
removed.
Basic Installation
Removing the existing receiver unit
Before installing, make sure that the ignitionswitch is set to OFF and remove the terminal of
the car battery to avoid short-circuiting.
Basic Installation
3
Installation
Bend the
claws
according to
the thickness
of the
dashboard.
1. Remove the rear support from the unit.
2. Remove the control panel and trim ring
from the unit.
3. Insert the lever into the hole on one side
of the unit. Perform the same operation on
the other side and pull the unit out from
the mounting sleeve.
1. Remove the existing receiver unit.
2. Make the necessary connections.
3. Install the installation sleeve.
4. Install the unit into the installation sleeve.
14
Installation
ISO-DIN Installation
Remote Control
Battery Installation
ISO-DIN Installation
Battery Installation
1
4
3
3
5
2
Installation
1. Slide the unit into the ISO-DIN frame.
2. Fit screws removed from the old unit.
3. Slide the unit and frame into the dash
opening.
4. Install the dash panel or adapter plate.
(According to models, this step may not be
needed.)
1. Pull out the battery holder with a sharp
product like a ball point pen.
2. Put the battery with
the battery holder.
and
correctly on
3. Push the battery holder back into its original
position.
5. Install the control panel to the unit.
NOTE
• Use only one CR2025 (3 V) lithium battery.
• Remove the battery if the remote control is not
used for a long period of time.
• Do not leave the product in a hot or humid
place.
• Do not handle the battery with metallic tools.
• Do not store the battery with metallic materials.
Installation
15
Connection
Connecting to a car
Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the
car battery to avoid short-circuiting.
Connection 1
3
Control Relay
AH Power Antenna (Blue)
AG Dimmer (Pink)
AB To Ignition (Red)
AA To Battery (+) (Yellow)
AE Ground(-) (Black)
AC Remote On (Blue/White)
AD Phone Mute (Orange)
AF Hand Brake (Sky blue)
BA Violet/ Black Stripe: Rear Right BB Violet: Rear Right +
BC Gray/ Black Stripe: Front Right BD Gray: Front Right +
BE Green/ Black Stripe: Rear Left BF Green: Rear Left +
BG White/ Black Stripe: Front Left BH White: Front Left +
Installation
Power
Antenna
16
Installation
Connecting to optional equipment
You can connect optional equipment to the corresponding terminals of the unit.
Connection 2
Auxiliary devices
(Car TV, monitor, etc.)
Amplifier (Optional)
3
Installation
Rear view camara
Rear signal from rear view camera
Wired remote input (Optional)
No.
Terminal
Position
1
Video IN
Rear view cameras
2
Audio out
Rear left speaker or
Subwoofer left (Optional)
3
Audio out
Rear right speaker or
Subwoofer right (Optional)
4
Video out
Auxiliary devices (Car TV, monitor, etc.)
5
Audio out
Front left speaker
6
Audio out
Front right speaker
7
Wired remote input
Hard-wired control adapter (Not supplied)
8
Rear signal from rear
view camera
Rear view camera
Installation
Adjusting the general
settings
You can change the settings of the unit by
pressing MENU.
MENU item overview
XDSS+
/EQ
OFF
XDSS+
Pop
Classic
Rock
Jazz
Vocal
Salsa
Samba
Reggae
Russy
User 1
User 2
Balance/Fader
Sound
The buttons for setting MENU
User EQ 1/2
Auto-EQ
DRC
Remote
control
Press
MENU
MENU
Operation
Language
TV Aspect
Activates or deactivates
a setting menu.
Rotate
volume
knob
U/u
• Moves to other menu
items.
I/i
• Adjusts the setting
level.
Press
volume
knob
LIST/
ENTER
• Confirms the selected
menu or the set level.
• Selects or sets the
menu option, only
when just 3 menu
options exist.
B.L.E
Display
Album Art
TV System
Code Page
Brightness
Light
Contrast
DVD Audio Lang
DVD Subtitle Lang
RETURN • When it is pressed,
you can move to the
previous step.
• When it is pressed and
held, you can return
to the playback status.
DVD Menu Lang
Setup
Lock
REC Bit Rate
Beep
Clock
3
Installation
Subwoofer
Main
unit
17
18
Installation
XDSS+/EQ
The function helps you to enjoy sound more
plentifully. The indicator lights up in the
following order.
OFF t XDSS+ t Pop t Classic t Rock t
Jazz t Vocal t Salsa t Samba t Reggae
t Russy t User 1 t User 2 t ..
5. Adjust the fader (front/ rear speaker) level
by using the volume knob (U or u on the
remote control).
Sound
Balance/ Fader
3
You can adjust left/right/ front/rear speaker
output.
Installation
1. Press MENU.
2. Select [Sound] and press the volume knob
(LIST/ENTER on the remote control).
3. Select [Balance/Fader] and press the
volume knob (LIST/ENTER on the remote
control).
4. Adjust the balance (left/ right speaker) level
by using the volume knob (U or u on the
remote control).
And press the volume knob (LIST/ENTER
on the remote control).
Subwoofer
Subwoofer level
Adjusts the subwoofer output.
Subwoofer Frequency
Adjusts the subwoofer frequency .
User EQ 1/2
You can adjust Bass, Middle, or Treble levels
by rotating the volume knob on the unit or
pressing I or i on the remote control.
Auto-EQ
It realizes the sound equalizer that is the most
similar to the genre of which is included in the
ID3 tag of song files. Auto-EQ operates only
in the music file supported with genre in the
device.
And press the volume knob (LIST/ENTER
on the remote control).
DRC(Dynamic Range Control)
Makes the sound clear when the volume is
turned down (Dolby Digital only). Set to [ON]
for this effect.
Installation
Display
Language
Selects a language for the Setup menu and
on- screen display.
TV Aspect
Select a TV aspect ratio option according to
your monitor type.
19
[Full Screen]
Displays both title texts and album art
images of ID3 tag in full screen.
TV System
You should select an appropriate system mode
for your monitor system among NTSC, PAL, or
Auto.
Code Page
[4:3 Letter Box]
Select when a standard 4:3 monitor is
connected. Displays theatrical images with
masking bars above and below the picture.
[4:3 Pan Scan]
Select when a standard 4:3 monitor is
connected. Displays pictures cropped to
fill your monitor screen. Both sides of the
picture are cut off.
If the CD TEXT, ID3 TAG, or movie file’s subtitle
is not displayed properly, you can change the
code page to view it properly.
1. Select an appropriate code page by using
the volume knob (U or u on the remote
control).
2. Press the volume knob (LIST/ENTER on the
remote control) repeatedly until the text is
displayed properly and then press it.
Light
Brightness
B.L.E (Black Level Enhancement)
Adjusts the brightness level of the display
window for Daylight or Nighttime.
Enhances the black level only when you set
your monitor to NTSC.
Contrast
Album Art
Adjusts the contrast level of the display
window for Daylight or Nighttime.
When listening to music files, you can select
the display view by pressing DISPLAY. Then,
if you set Album Art view, you can adjust the
view to your reference.
[Text]
Displays only the texts of ID3 tag or CD text.
[Thumbnail]
Displays both texts and album art images of
ID3 tag.
NOTE
According to the dimmer status of a car, the unit
recognizes Daylight or Nighttime.
3
Installation
[16:9]
Select when a 16:9 wide monitor is
connected. The 4:3 picture is adjusted
horizontally (in a linear proportion) to fill
the entire screen.
20
Installation
Setup
DVD Audio / DVD Subtitle / DVD
Menu Language
Select the language you prefer for the audio
track (disc audio), subtitles, and the disc menu
during DVD playback.
Original
Refers to the original language in which the
disc was recorded.
3
Lock
Installation
Password
You can change password. When you use
the unit first, input the default password of
0000.
1. Input a current password and press the
volume knob (LIST/ENTER on the remote
control).
2. Input a new password and press the
volume knob (LIST/ENTER on the remote
control).
3. Enter the password again and press the
volume knob (LIST/ENTER on the remote
control) to verify.
Area Code
Enter the code of the area whose standards
were used to rate the DVD video disc, based
on the list on page 31.
Rating
Blocks playback of rated DVD based on their
content. (Not all discs are rated.)
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
REC Bit Rate
You can set the quality of the recorded file
among 96 Kbps, 128 Kbps, or 192 Kbps.
Beep
2nd
The beep is generated when a key is pressed
for longer than 2 seconds.
All
The beep is generated when any key is
pressed.
OFF
The beep is deactivated.
Clock
Only when you set CT to OFF on the Func
menu of Tuner mode, you can adjust it.
Time format
You can adjust the time system between 12
Hours and 24 Hours systems.
Clock Setting
Set the hour and then the minute by using
the volume knob (U or u on the remote
control). After setting each one, press the
volume knob (U or u on the remote control)
to confirm it.
NOTE
If you set the Time Format to 12 Hours , you should
set one between AM and PM first.
Operation
21
4
Operation
Basic Operations
Before watching DVD
DVD MOVIE
1. Turn the unit on by pressing any key on the
unit.
2. Insert the disc after pressing or connect
the USB device to the USB port.
When you attempt to watch a DVD, the screen
is displayed as below. Then, select [Yes] or [No]
by rotating the volume knob or pressing
I or i on the remote control.
3. Select the Disc or USB function by pressing
SRC.
4
Operation
4. Rotate the volume knob on the unit or
press VOL.+/- on the remote control.
NOTE
Make sure to press Z after opening
front
pressing theon
the
to
release
a
disc.
Refer
to
the
picture
as
panel
front panel to release a disc. Refer to the picture
below.
as below.
[Yes]
The playback starts without any restriction.
[No]
The screen is turned black 5 seconds after
selecting the item. However, when you
press any key, the screen is turned on and
off after 5 seconds.
NOTE
To use a mixed disc or USB
device
When playing a disc or USB device containing
with audio, video, and photo files together, you
can select a file category which you would like
to play by pressing BAND.
Even though you select [No], if you connect a hand
brake line to the unit, the screen is not turned black
even after 5 seconds.
22
Operation
To pause playback
Other Operations
Press NX (X on the remote control) during
playback.
Press NX (B on the remote control) to
resume playback.
To display file information
To scan forward or backward
• On the unit
Press and hold b[- or +[B repeatedly during
playback to play fast forward or fast reverse
with various playback speeds.
• On the remote control
Press m or M repeatedly during playback
to play fast forward or fast reverse with various
playback speeds.
If you want to display a currently playing file/
disc during playback, press
(DISPLAY on
the remote control).
NOTE
For music files, press
(DISPLAY on the
remote control) repeatedly during playback,
you can set the display background with File
name, ID3 TAG, or Clock time.
4
Operation
To skip to the next/previous
chapter/track/file
During playback, press b[- or +[B (. or
> on the remote control) to go to the next
chapter/track/file or to return to the beginning
of the current chapter/track/file.
Press b[- (. on the remote control) twice
briefly to step back to the previous chapter/
track/file.
Turning off the sound
temporarily
1. Press MUTE to mute your unit.
2. To cancel, press any key.
To slow down the playing speed
While the playback is paused, press M
repeatedly to play various speeds of slow
motion for movie files.
To play frame-by-frame
Press X while movie playback.
Press X repeatedly to play Frame-by-Frame
playback.
Operation
Quick search
1. Press the volume knob (LIST/ENTER on the
remote control) to check files.
23
NOTE
• If no button is pressed for 10 seconds, the onscreen display disappears.
• A title number cannot be selected on some
discs.
• Available items may differ depending on discs
or titles.
Using the Func menu
2. Press
(RETURN on the remote control)
to check folders.
By adjusting the Func menus, you can enjoy
files/track/chapters in a way you want.
3. Select a desired folder by using the volume
knob (U/u/I/i on the remote control).
1. Press MENU.
4. Press the volume knob (LIST/ENTER on the
remote control).
6. Press the volume knob on the unit (LIST/
ENTER on the remote control) to start
playback.
For a DVD disc, you can search according to
the items below. When you select Title Search
or Chpter Search, you can select a desired
chapter or title by using the volume knob (U
or u on the remote control) after the step 1.
3. Select a desired item by using the volume
knob (U or u on the remote control).
4. Press the volume knob (LIST/ENTER on the
remote control) repeatedly to adjust items.
(RETURN on the remote control)
5. Press
to return to the previous menu.
[Repeat]
DVD MOVIE MUSIC PHOTO
Sets repeat playback according to File,
Folder, Track, Title or Chapter.
[Shuffle]
MUSIC
Sets random playback according to Files,
Folders, or Tracks. During random playback,
even if you press b[-(. on the remote
control) , you won’t go back to the previous
track.
[Intro Scan]
MUSIC
The first 10 seconds of each tracks/files on
the disc or in the current selected folder are
played.
4
Operation
5. Select a desired file/ track by using the
volume knob(U or u on the remote
control).
2. Select Func and press the volume knob
(LIST/ENTER on the remote control).
24
Operation
[Audio]
DVD MOVIE
Sets audio language or channel.
[Subtitle]
DVD MOVIE
Sets a desired subtitle language.
[Angle]
DVD
If the disc contains scenes recorded at
different camera angles, you can change to
a different camera angle during playback.
Using the time search bar
DVD
MOVIE
Using the time search bar, you can find easily
the point where you want to start playback of
movie files.
1. During playback, press and hold the volume
knob (LIST/ENTER on the unit) until the bar
turns red.
NOTE
4
For adjusting Repeat, Shuffle, Intro Scan, Audio
language, Subtitle, or Angle menu, you can
simply use the short-cut buttons on the remote
control.
Operation
2. Rotate the volume knob on the unit or
press I or i to select a point that you want
to play.
3. Press the volume knob (LIST/ENTER on the
remote control).
Resume playback
DVD
The unit records the point where you pressed
x depending on the disc.
If “Xx (Resume Stop)” appears on the screen
briefly, press B to resume playback (from the
scene point).
If you press x twice, “x”(Complete Stop)
appears on the screen. The unit will clear the
stopped point.
NOTE
The resume point may be cleared when the unit is
turned off or the inserted disc is released.
Operation
Viewing a photo
Adjusting the speed of slide show
1. Press the volume knob (LIST/ENTER on the
remote control) to check files.
You can set the slide show speed on the Func
menu.
2. Press
(RETURN on the remote control)
to check folders.
3. Select a desired folder by using the volume
knob (U or u on the remote control).
4. Press the volume knob (LIST/ENTER on the
remote control).
5. Select a desired file by using the volume
knob (U or u on the remote control).
6. Press the volume knob (LIST/ENTER on the
remote control) to view a photo.
25
1. Press MENU.
2. Select Func and press the volume knob
(LIST/ENTER on the remote control).
3. Select Slide Show by using the volume
knob (U or u on the remote control).
4. Press the volume knob (LIST/ENTER on the
remote control) repeatedly to set the speed
among Slow, Normal, or Fast.
Listening to the radio
To skip to the next/previous photo
NOTE
If you want to go to the first file of a previous or
next folder, press U or u on the remote control.
To rotate a photo
Press m or M on the remote control to
rotate a photo clockwise or counter-clockwise.
Viewing photo files as a slide show
1. Press NX (B on the remote control) to
start slide show.
2. Press NX (X on the remote control)
during slide show to pause a slide show.
1. Select Tuner by pressing SRC.
4
2. Select a band by pressing BAND.
Operation
While viewing a photo, press b[- or +[B
(I or i on the remote control) to go to the
previous or next photo.
3. For manual search, press and hold b[-/+[B
on the unit or I or i on the remote control
until “Manual“ is displayed. Then press it
repeatedly to select a desired frequency.
]For auto search, press b[-/+[B on the
unit or I or i on the remote control until
“Search” is displayed.
4. Rotate the volume knob on the unit or
press VOL.+/- on the remote control.
26
Operation
Storing desired frequencies
manually
Adjusting Tuner settings
1. Press BAND to select a desired band you
want to store.
2. Select Func and press the volume knob
(LIST/ENTER on the remote control).
2. Press and hold b[-/+[B on the unit or
I or i on the remote control and then
press it repeatedly to select a desired
frequency.
3. Select a desired item by using the volume
knob (U or u on the remote control).
3. Select a desired preset number .
• On the unit
Press the volume knob and rotate it. Then,
press it again to store.
• On the remote control
Press and hold one of preset buttons among
1-6 on the remote control until the beep
sound is heard.
4
4. Repeat steps 1-3 to preset other stations.
Operation
NOTE
ayb
palck.When a station is stored on the preset numbers
on which another station of the same band has
already been preset, the previously preset station is
automatically erased.
Listening to a preset station
1. Press BAND to select a desired band.
2. Press the volume knob on the unit or LIST/
ENTER on the remote control.
3. Rotate the volume knob on the unit or
press I or i on the remote control to
select a preset station.
4. Press the volume knob (LIST/ENTER on the
remote control).
Or
Press BAND and then the desired preset
button among 1-6 on the remote control.
1. Press MENU.
4. Press the volume knob (LIST/ENTER on the
remote control) repeatedly to adjust items.
(RETURN on the remote control)
5. Press
to return to the previous menu.
Auto Store
The six strongest broadcasting frequencies
will be stored under preset button 1-6 in
the order of their signal strength.
To cancel, press BAND or SRC.
Preset scan
Each preset station of each band is
displayed in blue.
To cancel, press BAND or SRC.
Sensitivity
In an area in which signal reception is weak,
it helps the tuner to search more stations.
You can set the signal reception sensitivity
differently according to areas.
[Local] In areas with good signal strength
[Normal] In areas with good normal
strength
[Dx] In areas with bad signal strength
Operation
27
Enjoying music or
movie by connecting
an external device
You can enjoy music or movie files of an
external device by connecting it to the unit.
1. Connect an external device to the AUX jack
with line input cable.
2. Select AUX by pressing SRC.
3. Play the connected Auxiliary Equipment.
4. Rotate the volume knob on the unit or
press VOL.+/- on the remote control.
You can adjust the volume level of each source
to prevent radical changes in volume by
adjusting AUX Input Gain.
1. Press MENU.
2. Press the volume knob (LIST/ENTER on the
remote control) repeatedly to select AUX
Input Gain from -6 dB to +6 dB.
(RETURN on the remote control)
3. Press
to return to the previous menu.
4
Operation
Preventing radical changes in
volume as switching sources
28
Operation
Recording to USB
from Disc or FM tuner
(RETURN on the remote
5. Press REC or
control) again to stop.
NOTE
1. Open the USB cover and connect it to the
unit.
2. Select Disc or FM tuner.
• When USB memory is full, “Not Enough Memory”
displays and stops recording.
3. Start playback.
• For tuner recording, the broadcastings are
recorded by 20 moments on a file name.
4. On FM tuner mode, press REC to start
recording.
On CD playback mode, press REC then the
menu items are displayed as below;
Track
4
• Do not remove the USB device during recording,
or an incomplete file may be made and not
deleted on PC.
You can record a desired track.
Operation
1. Press the volume knob (LIST/ENTER on
the remote control).
2. By rotating the volume knob (LIST/ENTER
on the remote control) to select a desired
track.
3. Press the volume knob (LIST/ENTER on
the remote control).
All
You can record all of the tracks.
Remaining
You can record from the selected track and
all of the remaining tracks.
1. Select [Remaining] by using the volume
knob (U or u on the remote control).
2. Press the volume knob (LIST/ENTER on
the remote control).
3. By rotating the volume knob (LIST/ENTER
on the remote control) to select a desired
track.
4. Press the volume knob (LIST/ENTER on
the remote control).
• If the USB is removed, the front panel gets open,
or the unit is turned off during recording, the
recording stops.
• If recoring is abruptly stopped, just the file
name is saved in a corresponding folder with no
recording data.
Maintenance
29
5
Maintenance
Notes on Discs
Handling the Unit
Handling Discs
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit,
for maximum protection, re-pack the unit as it
was originally packed at the factory.
Never stick paper or tape on the disc.
Storing Discs
Cleaning Discs
•
Do not use volatile liquids such as
insecticide spray near the unit.
•
Wiping with strong pressure may damage
the surface.
•
Do not leave rubber or plastic products in
contact with the unit for a long period of
time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If
the surfaces are extremely dirty, use a soft
cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as
alcohol, benzine, or thinner, as these might
damage the surface of the unit.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available
cleaners, or anti-static spray intended for older
vinyl records.
Maintaining the Unit
The unit is a high-tech, precision device. If
the optical pick-up lens and disc drive parts
are dirty or worn, the picture quality could be
diminished. For details, please contact your
nearest authorized service centre.
5
Maintenance
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of
heat and never leave it in a parked car exposed
to direct sunlight.
Keeping the exterior surfaces clean
30
Troubleshooting
6
Troubleshooting
Symptoms
Solution
The power does not
turned on./ The unit
doesn’t operate.
•
Confirm once more that all connections are correct.
•
Rectify the problem that caused the fuse to blow, and then
replace it. Be very sure to install the correct fuse with the
same rate.
•
Turn the unit off and then on again.
There is no sound or the
sound is distorted.
6
Troubleshooting
•
The unit is in scan, slow motion, or pause mode.
•
The sound volume is low.
•
Connect the cables correctly. (page 15)
There’s audio skipping.
•
Secure this unit firmly.
The unit does not start
playback.
•
Insert a playable disc. (Check the disc type, colour system,
and regional code.)
•
Place the disc with the playback side down.
•
Clean the disc.
•
Cancel the rating function or change the rating level.
Radio stations cannot be
tuned in properly.
•
Tune to stations manually.
•
Preset some stations.
The remote control does
not work properly.
•
The remote control is not pointed at the remote sensor of
the unit.
•
The remote control is too far from the unit.
•
There is an obstacle in the path of the remote control and
the unit.
•
Load a new battery.
Appendix
31
7
Appendix
Area Code List
Choose an area code from this list.
Area
Code Area
Code Area
Code Area
Code
Afghanistan
AF Fiji
FJ Monaco
MC Singapore
SG
Argentina
AR Finland
FI Mongolia
MN Slovak Republic
SK
Australia
AU France
FR Morocco
MA Slovenia
Austria
AT Germany
DE Nepal
NP South Africa
ZA
Belgium
BE Great Britain
GB Netherlands
NL South Korea
KR
Bhutan
BT Greece
Bolivia
BO Greenland
GR Netherlands
GL Antilles
Brazil
BR Hong Kong
Cambodia
KH Hungary
Canada
CA India
Chile
CL Indonesia
China
CN Israel
CO Italy
Congo
CG Jamaica
Costa Rica
CR Japan
Croatia
HR Kenya
Czech Republic
CZ Kuwait
Denmark
DK Libya
Ecuador
EC Luxembourg
Egypt
EG Malaysia
El Salvador
SV Maldives
Ethiopia
ET Mexico
IN Norway
ID Oman
IL Pakistan
IT Panama
JM Paraguay
JP Philippines
KE Poland
KW Portugal
LY Romania
LU Russian
Federation
MY
Saudi Arabia
MV
Senegal
MX
ES
AN Sri Lanka
NZ Sweden
LK
NG Switzerland
NO Taiwan
CH
SE
TW
OM Thailand
PK Turkey
TH
PA Uganda
PY Ukraine
UG
PH United States
PL Uruguay
TR
UA
US
UY
PT Uzbekistan
RO Vietnam
UZ
Zimbabwe
ZW
RU
SA
SN
Appendix
Colombia
HK New Zealand
HU Nigeria
Spain
SI
VN
7
32
Appendix
Specifications
AUX
General
Output Power:
53 W x 4 CH (Max.)
Power Source:
DC 12 V
Speaker impedance:
Ground System:
4Ω
Negative
Frequency Response:
20 Hz to 20 kHz
S/N Ratio:
85 dB
Distortion:
0.1 %
Channel Separation (1 kHz):
55 dB
Max Input Level (1 kHz):
Dimensions (W x H x D):
2V
178 x 50 x 169 mm (Without Control Panel)
Net Weight (Approx.):
1.42 kg
USB
TUNER
Version
FM Tunning Range:
87.5 to 107.9 or 87.5 to 108 MHz
USB 1.1 or USB 2.0 Full Speed
Bus Power Supply (USB)
DC 5V
500 mA
AM Tunning Range:
520 to 1720 or 522 to 1620 kHz
Line OUT
Frequency Response:
CD
Appendix
Frequency Response:
20 Hz to 20 kHz
S/N Ratio:
85 dB
Distortion:
0.1 %
Channel Separation (1 kHz):
55 dB
2 V (Max.)
Subwoofer(OPTIONAL)
Frequency Response:
Output Voltage:
7
20 Hz to 20 kHz
Output Voltage:
20 Hz to 120 Hz
2 V (Max.)
Appendix
33
Trademarks and Licences
Manufactured under licence from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
Appendix
7
Download PDF