LG | MAX620BO | LG MAX620BO Owner’s Manual

ENGLISH
OWNER’S MANUAL
DIGITAL MEDIA RECEIVER
Please read this manual carefully before operating
your set and retain it for future reference.
MAX620BO
2
Getting Started
Safety Information
CAUTION
1
RISK OF ELECTRIC SHOCK
DO NOT OPEN
or any functions. Pull over in a safe and
legal manner before attempting such
operations.
Do not use for many hours
at extremely low or high
temperature. (-10 °C to 60 °C)
Getting Started
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT REMOVE COVER
(OR BACK) NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
To reduce the risk of electric
shock, do not remove the cover
or back of this product. There
are no user-serviceable parts inside. Refer
servicing to qualified service personnel.
This lightning flash with
arrowhead symbol within
an equilateral triangle is
intended to alert the user to
the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
To reduce the risk of fire or
electric shock, do not expose this
product to dripping or splashing
water, rain, or moisture.
The exclamation point within
an equilateral triangle is
intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC
SHOCK HAZARD, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
WARNING: Do not install this equipment
in a confined space such as a book case or
similar unit.
Always operate the vehicle in
a safe manner. Do not become
distracted by the vehicle while
driving, and always be fully aware of all
driving condition. Do not change settings,
The temperature of unit’s outside
can be extremely high, please use
the unit after proper installation
in your vehicle.
While driving, keep the sound
volume at a proper level.
Do not drop it and avoid heavy
impacts at anytime.
This unit is for vehicles with a
12-volt battery and negative
grounding. Before installing it in
a recreational vehicle, lorry or bus, check
the battery voltage. To avoid shorts in the
electrical system, be sure to disconnect
the E battery cable before beginning the
installation.
This device is equipped with a portable
battery or accumulator.
Disposal of waste batteries/
accumulators
Safe way to remove the battery or the
battery from the equipment:
1. When this crossed-out
wheeled bin symbol is attached
to batteries/accumulators of Your
product it means they are covered by
European Directive 2006/66/EC.
Remove the old battery or battery pack,
follow the steps in reverse order than the
assembly. To prevent contamination of
the environment and bring on possible
threat to human and animal health, the
old battery or the battery put it in the
appropriate container at designated
collection points. Do not dispose of
batteries or battery together with other
waste. It is recommended that you
use local, free reimbursement systems
batteries and accumulators.
The battery shall not be exposed to
excessive heat such as sunshine, fire or
the like.
2. This symbol may be combined with
chemical symbols for mercury(Hg),
cadmium(Cd) or lead(Pb) if the battery
Contains more that 0.0005% of
mercury,0.002% of cadmium or 0.004% of
lead.
3. All batteries/accumulators should be
disposed separately from the municipal
waste stream via designated collection
facilities appointed by the government or
the local authorities.
4. The correct disposal of Your old
batteries/accumulators will help to
prevent potential negative consequences
for the environment, animal and human
health.
5. For more detailed information
about disposal of Your old batteries/
accumulators, please contact Your city
office, waste disposal service or the shop
where You purchased the product.
Disposal of your old appliance
1.When this crossed-out wheeled
bin symbol is attached to a
product it means the product is
covered by the European
Directive 2002/96/EC.
Table of Contents
2. All electrical and electronic products
shall be disposed of separately from the
municipal waste stream via designated
collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you purchased
the product.
LG Electronics hereby
declares that this/these
product(s) is/are in
compliance with the essential
requirements and other relevant
provisions of Directive 2004/108/EC,
2006/95/EC and 2009/125/EC.
European Standards Centre:
Krijgsman 1, 1186 DM Amstelveen The
Netherlands
 Please note that this is NOT a Customer
Service contact point. For Customer
Service Information, see Warranty
Card or contact the dealer that you
purchased this product.
Indoor Use Only
RF Radiation Exposure Statement
This equipment should be installed and
operated with minimum distance 20 cm
between the radiator and your body.
Table of Contents
8
9
1
Getting Started
2
4
4
5
Safety Information
Front panel
Remote control
– Battery Installation
2
Connecting
5
5
5
Installation
– Basic Installation
– Removing the existing
receiver unit
– ISO-DIN Installation
About detachable control
panel
Connection
– Connecting to a car
5
6
7
7
9
9
9
10
10
11
11
11
11
11
11
3
Operating
8
8
8
Operation
– Basic operations
– Turning off the sound
temporarily
– Checking the clock
– Resetting the unit
8
8
11
11
12
12
– Adjusting the general
settings
Listening to music from an
external device
– Preventing radical changes
in volume as switching
sources
Listening to the radio
– Storing desired
frequencies manually
– Listening to a preset
station
– Adjusting TUNER settings
Using a SD card
– Pausing or restarting
playback
– Searching for a section
within a file
– Skipping to another file
– Checking information
about your music
– Playing back files in a way
you want
– Quick search of a desired
file
– Playable SD card
Requirement
Listening to music by
connecting iPod/iPhone
– Pausing or restarting
playback
12
3
16
– Searching for a section
within a file
– Skipping to another file
– Checking information
about your music
– Playing back files in a way
you want
– Playing back files by music
menus
– iPod/ iPhone CONTROL
MODE
– Compatible iPod / iPhone
models
Connecting a Bluetooth
wireless technology
– Using a Bluetooth wireless
technology
– Adjusting the setting
– Using "LG CAR Remote"
application
– Phone compatibility list
4
Troubleshooting
18
Troubleshooting
5
Appendix
19
Specifications
12
12
12
12
13
13
13
14
14
15
1
2
3
4
5
4
Getting Started
Front panel
j U
Skip / Search / Seek / Tune
CALL
Answers a call.
END
Ends a call.
1
Getting Started
k
Remote control
F
In each mode, sets playback items.
• MENU
Activates setting menu.
l 6
Opens the front panel.
m Remote Sensor
a T
Plays and pauses playback.
• TA (Optional)
Searches stations that have TA / TP
information, when it is pressed and
held.
d R (EJECT)
Ejects the iPod/ iPhone DOCKING
STATION.
b SRC
When pressed, selects function
sources.
• OFF
When pressed and held, powers unit
off.
g AUX
If connected to other portable player,
you can enjoy music from it on the
unit.
c DISP
Press it, you can check the clock time.
• APP
Activates "LG CAR Remote"
application.
e Display window
f iPod/iPhone DOCKING STATION
h Y
Skip / Search / Seek / Tune
Returns to the previous step.
i Volume knob
- Adjusts volume level.
- Confirms the settings.
- Checks files or preset stations.
a SRC
When pressed, selects function
sources.
• OFF
When pressed and held, powers unit
off.
b FUNC
When pressed, sets playback items in
each mode.
• MENU
When pressed and held, activates
setting menu.
c BAND/DRV
Selects a band in Tuner mode.
d d/M Plays or pauses playback.
e SHF Shuffles playback.
f MUTE Temporarily stops the sound.
g VOLUME W / S
Adjusts volume level.
Connecting
h c/v
Skip / Search / Seek / Tune
Battery Installation
Installation
Type 1
i DISP
Press it, you can check the clock time.
Basic Installation
Before installing, make sure that the
ignition-switch is set to OFF and remove
the terminal of the car battery to avoid
short-circuiting.
ISO-DIN Installation
Bend the claws
according to
the thickness of
the dashboard.
2
Type 2
2
1
j RPT
Repeats playback.
Control panel
k INT
Intro scan.
l Numeric buttons (1 to 6)
Selects a numbered preset station in
TUNER.
1. Remove the rear support from the unit.
2. Remove the control panel and trim
ring from the unit.
3. Insert the lever into the hole on one
side of the unit. Perform the same
operation on the other side and pull
the unit out from the mounting sleeve.
Connecting
Returns to the previous step.
w/s
- List up / down
- Adjusts settings.
- Moves 10 MP3 / WMA files
backward or forward if there is no
folder or one folder on a SD card.
- Moves to the previous or next
folder if there are more than 2
folders on a SD card.
ENTER / LIST
- Confirms the settings.
- Checks files or preset stations.
5
, Note
 Use only one CR2025 (3 V) lithium
battery.
 Remove the battery if the remote
control is not used for a long
period of time.
 Do not leave the product in a hot
or humid place.
 Do not handle the battery with
metallic tools.
 Do not store the battery with
metallic materials.
1.
2.
3.
4.
Remove the existing receiver unit.
Make the necessary connections.
Install the installation sleeve.
Install the unit into the installation
sleeve.
Removing the existing
receiver unit
If there is already an installation sleeve for
the receiver unit in the dashboard, it must
be removed.
Control panel
1. Slide the unit into the ISO-DIN frame.
2. Fit screws removed from the old unit.
3. Slide the unit and frame into the dash
opening.
4. Install the dash panel or adapter plate.
(According to models, this step may
not be needed.)
5. Install the trim ring to the unit.
6. Install the control panel to the unit.
6
Connecting
About detachable
control panel
Detaching the control panel
1. Press the 6 to open the control
panel.
Attaching the control panel
2. Lift the control panel slightly.
3. Push the control panel to right.
2
Connecting
1. Align the left side of the panel with the
stopper.
2. Push the right side of panel into the
unit until it clicks.
> Caution
 The control buttons may not work
properly if the control panel is not
attached properly. If this occurs,
gently press the display.
 Do not leave the control panel
in any area exposed to high
temperatures or direct sunlight.
 Do not drop the control panel
or otherwise subject it to strong
impact.
 Do not allow such volatile agents
as benzine, thinner, or insecticides
to come into contact with the
surface of the control panel.
5
6
4. Pull the control panel out of the unit.
5. Put the detached control panel into
the protective case.
Control panel
Protective Case
, Note
Periodically wipe the contacts on
the back of the control panel with a
cotton swap moistened with alcohol.
For safety, turn off the ignition before
cleaning, and remove the key from the
ignition switch.
Connecting
7
Connection
Connecting to a car
Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting.
Wired mic
Wired remote input (Black): Hard-wired control adapter can be connected. (Optional)
To Audio out
ab c d ab c d
e f g h e f g h
Sub-woofer Right
Front Right
Rear Right
Power
Antenna
When being connected in a wrong way, the unit displays as follows.
- Antenna / Remote port short: "ANTENNA/ REMOTE ON PORT SHORT CIRCUIT
CHECK"
B g Not connected
After connecting it again, restart the unit.
Ignition Switch
A
a
b
c
A
d
A
e
A
f
A
g
A
h
A
B d To Battery (+) (Yellow)
A
B h Ground (-) (Black)
B e Remote On
(Blue / White)
Amplifier
> Caution
Control Relay
B f Power Antenna (Blue)
B c To Ignition (Red)
Sub-woofer
Amplifier
A a Gray : Front Right +
A b Gray / Black Stripe: Front Right A c Violet : Rear Right +
A d Violet / Black Stripe: Rear Right A e White : Front Left +
A f White / Black Stripe: Front Left A g Green : Rear Left +
A h Green / Black Stripe: Rear Left -
B b Not connected
B a Not connected
2
Connecting
Sub-woofer Left
Front Left
Rear Left
To Audio in
8
Operating
Operation
Basic operations
1. Turn the unit on by pressing any key
on the unit.
2. Select a source by pressing SRC.
3. Rotate the volume knob to adjust the
volume on the unit.
Or press VOLUME W / S on the
remote control.
You can adjust [SOUND], [LIGHT] and
[OTHER] settings.
On the unit
1. Press T to mute your unit. (When
MP3/ WMA file is played, it will be
paused.)
Or press MUTE on the remote control.
2. Press it again to cancel
1. Press and hold • MENU.
2. Rotate the volume knob to select
[SOUND], [LIGHT], or [OTHER] and press
it.
3. Rotate the volume knob to select the
item and press it.
4. Rotate the volume knob clockwise or
counterclockwise to adjust the level.
5. Press the volume knob to confirm the
setting.
If you want to return to the previous
.
step, press
Checking the clock
On the Remote Control
Turning off the sound
temporarily
3
Adjusting the general
settings
Operating
1. Press DISP.
2. Press it again to cancel.
Resetting the unit
You can reset the unit when it does not
operate properly.
1. Detach the control panel.
Refer to page 6 for detaching the
control panel.
2. Press the RESET hole with a sharp
object.
1. Press and hold FUNC / • MENU.
2. Press w / s to select [SOUND], [LIGHT],
or [OTHER] and press ENTER.
3. Press w / s to select the mode and
press ENTER.
4. Press w / s to adjust the level.
5. Press ENTER to confirm the setting.
If you want to return to the previous
step, press
.
For [SOUND] setting
You can adjust sound quality by adjusting
the level BAL (left/right speaker), FAD
(front/rear speaker), SW (Subwoofer), SW-F
(Subwoofer frequency), A-EQ (Auto EQ).
 SW (Subwoofer)
You can adjust the volume of
subwoofer.
 SW-F (Subwoofer frequency)
OFF/ SW 55 Hz/ SW 85 Hz/ SW 120 Hz
You can enable the subwoofer.
 A-EQ (Auto EQ) OFF/ ON
AUTO EQ operates only in the music
file supported with genre in the device.
When you set AUTO EQ to ON, POP,
CLASSIC, ROCK, or JAZZ is automatically
selected according to the music genre.
 EQ (Equalizer)
EQ is to increase or decrease the signal
strength of audio frequencies. The
function helps you to enjoy sound more
plentifully.
FLAT /B-BOOST (BASS BOOSTER) /
POP / CLASSIC / ROCK / JAZZ
/ VOCAL / SALSA / SAMBA /
REGGAE / RUSSY / U-EQ1 / U-EQ2
 U-EQ1 / U-EQ2
When you set the EQ to U-EQ1/2 mode:
You can adjust the level of BAS (bass),
MID (middle), TRB(treble).
 EFFECT
OFF/ 3D SOUND/ MP3 OPTIMIZER
You can use 3D SOUND/ MP3
OPTIMIZER.
3D SOUND: This mode delivers
outstanding surround sound.
MP3 OPTIMIZER: This mode enhances
the quality of compressed music file.
, Note
3D SOUND/ MP3 OPTIMIZER is only
available when you use the SD card.
For [LIGHT] setting
You can adjust the light effects by
adjusting DIM, or DIM LV.
 DIM (Dimmer) OFF / ON : You can
change the brightness of the display
window during the power-on status.
Settings
Description
DIM ON
The display window
becomes dark.
DIM OFF
The display window
becomes bright.
 DIM LV (Dimmer Level) : When you set
DIM to ON, you can adjust the dimmer
level. (-2, -1, 0, +1, +2)
Operating
For [OTHER] setting
 AUX (Auxiliary) ON / OFF
It is possible to use auxiliary equipment
with this unit. Activate the auxiliary
setting when using auxiliary equipment
connected to this unit.
 DEMO OFF / ON
You can change the initial indication
on the display to information name
(function name, EQ name, etc...) while
listening to a source.
 BEEP 2ND / ALL
BEEP 2ND : The beep is generated
when a key is pressed for longer than 2
seconds.
BEEP ALL : The beep is generated when
any key is pressed.
Listening to music from
an external device
1. Connect an external device to the AUX
jack with line input cable.
2. Select a source to AUX.
3. Play the connected Auxiliary
Equipment.
Preventing radical changes in
volume as switching sources
Only when you set AUX to ON as
switching sources, you can adjust the
volume level of each source to prevent
radical changes in volume by selecting
GAIN 0/ +3/ +6.
1. Press F on the unit.
Or press FUNC / • MENU on the remote
control.
2. Rotate the volume knob on the unit.
Or press w / s on the remote control
to set the option. (GAIN 0/ +3/ +6)
3. Press the volume knob on the unit.
Or press ENTER on the remote control
to confirm the setting.
4. If you want to return to the previous
step, press
.
Or press
on the remote control.
Listening to the radio
1. Press SRC repeatedly to select a source
to TUNER.
2. Press F to select BAND and then set
BAND to desired band.
3. For manual search, press and hold
Y/U on the unit until “MANUAL“
is displayed. Then press it repeatedly to
select a desired frequency.
Or press and hold c / v on the
remote control.
For auto search, press Y/U on
the unit. Then “SEARCH” is displayed.
(Except MW)
Or press c / v on the remote
control.
Storing desired frequencies
manually
1. Press F to select BAND and then set
BAND to desired band.
2. Select the desired frequency by using
Y/U on the unit.
Or use c / v on the remote
control.
3. Press the volume knob and rotate the
volume knob to select a preset station
among 1 to 6 and then press and hold
the volume knob until the beep sound
is heard.
Or press and hold one of preset
buttons among 1 to 6 on the remote
control until the beep sound is heard.
4. Repeat steps 1 to 3 to preset other
stations.
3
Operating
 CLOCK
For the model RDS is not supported unit
or even for a RDS supported unit.
- When RDS CT information is not
received and then you set CT to OFF,
you can adjust the time by yourelf. Set
the clock as follows ;
1. Select a source to TUNER.
2. Press F to select the CT and
then set CT to OFF. (Refer to the
" Adjusting TUNER settings " on
the page 10 for setting the CT
(Clock Time) ON / OFF.)
3. Press and hold • MENU on the unit to
select [OTHER] and then select
CLOCK by rotating the volume knob.
4. Set the hour by rotating the volume
knob.
5. Press the volume knob to confirm
the hour.
6. Set the minute by rotating the
volume knob.
7. Press the volume knob to confirm
the minute.
- When RDS CT information is received;
The clock is displayed according to
the RDS CT information.
- When RDS is not supported, set the
clock according to 3 to 7 steps.
9
10
Operating
, Note
When a station is stored on the
preset numbers on which another
station of the same band has already
been preset, the previously preset
station is automatically erased.
Listening to a preset station
1. Press F to select BAND and then set
3
Adjusting TUNER settings
On the unit
1. Press F .
2. Rotate the volume knob to select an
item and press it.
3. Rotate the volume knob to set the
option and press it.
4. If you want to return to the previous
step, press
.
Operating
BAND to desired band.
2. Press the volume knob on the unit.
Or press ENTER on the remote control.
3. Rotate the volume knob to select a
preset station.
Or press w / s on the remote control.
4. Press the volume knob.
Or press ENTER on the remote control.
Or
On the Remote Control
Selects the desired band and then press
the desired preset button among 1 to 6
on the remote control.
 BAND
You can select the desired band.
FM1/ FM2/ FM3/ MW (AM)
1. Press FUNC / • MENU.
2. Press w / s to select an item and press
ENTER.
3. Press w / s to set the option and press
ENTER.
4. If you want to return to the previous
step, press
.
 A / S (Auto Store)
The six strongest broadcasting
frequencies will be stored under preset
button 1 to 6 in the order of their signal
strength. To cancel, press the volume
knob.
 P / S (Preset scan)
Each preset station appears. To cancel,
press the volume knob.
 SENS (Tuner sensitivity) MID / HI / LOW
In an area in which signal reception is
weak, it helps the tuner to search more
stations. The weaker the reception is,
the lower option you should set to.
RDS (OPTIONAL)
 PTY (Program type)
It searches the radio stations by
program type of FM tuner.
The program types are displayed as
follows.
PTY OFF
WEATHER
ROCK M
NEWS
FINANCE
EASY M
AFFAIRS
CHILDREN
LIGHT M
INFO
SOCIAL
CLASSICS
SPORT
RELIGION
OTHER M
EDUCATE
PHONE IN
JAZZ
DRAMA
TRAVEL
COUNTRY
CULTURE
LEISURE
NATION M
SCIENCE
DOCUMENT
OLDIES
VARIED
POP M
FOLK M
 AF (Alternative Frequency) ON / OFF
When the reception quality drops, the
tuner automatically changes to another
station in the network, broadcasting a
better reception quality, using the PI
and AF codes.
 REG (Region) ON / OFF
REG ON : The unit switches to another
station, within the same network,
broadcasting the same program when
the receiving signals from the current
station become weak.
REG OFF : The unit switches to another
station, within the same network when
the receiving signals from the current
station become weak. (In this mode,
the program may differ from the one
currently received.)
 TA (Traffic Announcement) ALARM /
SEEK
TA ALARM : When the tuned station
has no TP information for 5 seconds, a
double beep sound is output.
TA SEEK : When the tuned station does
not receive TP information for 5 seconds,
the receiver retunes to the next station
that has the TP information.
 PI (Programme Identification) SOUND /
MUTE
PI SOUND : When the frequency
of a tuned station switches to an
AF (Alternative frequency) with an
unidentified PI, it keeps the sound.
PI MUTE : When the frequency of a
tuned station switches to an AF with an
unidentified PI, it mutes the sound until
the PI is identified.
 CT (Clock Time) ON / OFF
You can use the RDS CT information
to update the time. When RDS CT
information is not received and then
you set CT to OFF, you can adjust the
time by yourself. Refer to the page 9 for
setting the clock.
Operating
Using a SD card
1. Detach the control panel. (Refer to
"About detachable control panel" on
page 6.)
2. Insert the SD card.
Skipping to another file
On the Remote Control
Press Y/U on the unit.
Or press c / v on the remote
control.
1. Press INT / RPT / SHF.
2. Press it again to cancel.
Or
, Note
To skip to previous file, press briefly
Y within 3 seconds of playing
time.
Checking information about
your music
Pausing or restarting
playback
MP3 / WMA files often come with tags.
The tag gives the Title, Artist or Album.
Press DISP repeatedly during MP3 / WMA
file playback. If there is no information,
"NO TEXT" will be shown in the display
window.
1. PressT on the unit to pause
playback.
Or press d/M on the remote control.
2. Press it to resume playback.
Playing back files in a way
you want
Searching for a section
within a file
1. Press F .
2. Rotate the volume knob to select an
item and press it.
3. Rotate the volume knob to select the
option.
4. Press the volume knob to set the
option.
If you want to return to the previous
step, press
.
1. Press and hold Y/U on the unit
for about 1 second during playback.
Or press and hold c / v on
remote control.
2. Press T on the unit at the point you
want.
Or press d/M on the remote control.
On the unit
 RPT (Repeat)
The current selected file (1 RPT) or files
RPT)
in the current selected folder (
is played repeatedly.
 SHF (Shuffle)
All files (SHF) or each files in the current
SHF) are played
selected folder (
randomly. During random playback,
even if you press Y, you won't go
back to the previous file.
 INT (Intro Scan)
The first 10 seconds of all files (INT) or
each files in the current selected folder
INT) are played.
(
Quick search of a desired file
1. Press the volume knob on the unit.
Or press ENTER on the remote control.
2. Rotate the volume knob on the unit
to select a desired ROOT or folder and
press it.
Or press w / s and press ENTER on the
remote control.
3. Rotate the volume knob on the unit to
select a desired file and press it.
Or press w / s and press ENTER on the
remote control.
Playable SD card
Requirement
 SD card which requires additional
programme installation when you
have connected it to a computer, is not
supported.
 Regular back up is recommended to
prevent data loss.
 Some SD card may not work with this
unit.
 Using FAT (16 / 32) file system is
supported.
Max usage : 32 GB (FAT32 standard)
Using NTFS file system is supported to
read only.
 Using SD/ SDHC supported. Using SDXC
is not supported.
3
 Sampling Frequency / 8 kHz to 48 kHz
(MP3) 22.05 kHz to 48 kHz (WMA).
Bit rate / within 8 kbps to 320 kbps
(include VBR) (MP3) 32 kbps to 320 kbps
(WMA).
Operating
3. Attach the control panel.
4. Press SRC repeatedly to select a source
to SD.
1. Press FUNC / • MENU.
2. Press w / s to select an item and press
it.
3. Press w / s to select the option.
4. Press ENTER to set the option.
If you want to return to the previous
step, press
.
11
, Note
If you connect the iPod/ iPhone
while using the SD card, it may not
be able to charged.
12
Operating
Listening to music by
connecting iPod/iPhone
You can enjoy iPod / iPhone-stored music
on the unit.
1. Press R.
2. Connect the iPod / iPhone.
3. Press SRC to select a source to IPOD.
(iPod/ iPhone docking station can be
rotated by quarter)
, Note
During iPod/ iPhone playback, if the
iPod/ iPhone and the unit are paired
via Bluetooth wireless technology, it
may not sound. In such case, change
the audio output of the iPod/ iPhone
to "Dock Connector" or change the
input source of the unit to "BT".
Pausing or restarting
playback
1. Press T on the unit to pause
playback.
Or press d/M on the remote control.
2. Press it to resume playback.
Searching for a section
within a file
3
Operating
During playback, press and hold Y/
U and then release at a point you want.
Skipping to another file
Press Y/U on the unit.
Or press c / v on the remote
control.
> Caution
Please press R to close the iPod/
iPhone docking station when
you are not using it. When there
happen a sudden halt of a car or an
unexpected car accident, you might
be hurt by using the protruding
iPod/ iPhone docking station.
Checking information about
your music
MP3 / WMA files often come with tags.
The tag gives the Title, Artist or Album.
Press DISP repeatedly during MP3 / WMA
file playback. If there is no information,
"NO TEXT" will be shown in the display
window.
Playing back files in a way
you want
 SHF (Shuffle)
All of the files (SHF) on the iPod / iPhone
are played randomly.
 SPD (BOOK SPEED)
You can adjust the audiobook speed of
iPod / iPhone to NOR (Normal), SLOW or
FAST.
Playing back files by music
menus
You can check files by music menus and
play it back.
On the Unit
The music menus are as follows.
1. Press F .
2. Rotate the volume knob to select an
item and press it.
3. Rotate the volume knob to select the
option.
4. Press the volume knob to set the
option.
If you want to return to the previous
.
step, press
PLAYLISTS / ARTISTS / ALBUMS /
GENRES / SONGS / COMPOSER /
AUDIO BOOK / PODCAST / ...
On the Remote Control
1. Press RPT / SHF.
2. Press it again to cancel.
Or
1. Press FUNC / • MENU.
2. Press w / s to select an item and press
ENTER.
3. Press w / s to select the option.
4. Press ENTER to set the option.
If you want to return to the previous
step, press
.
 RPT (Repeat)
The current selected file (1 RPT) or
files on the iPod / iPhone is played
repeatedly.
1. Press the volume knob on the unit.
Or press ENTER on the remote control.
2. Rotate the volume knob on the unit to
select a music menu and press it.
Or press w / s on the remote control.
3. Rotate the volume knob on the unit to
select a file.
Or press w / s on the remote control.
4. Press the volume knob on the unit to
confirm the setting.
Or press ENTER on the remote control.
5. If you want to return to the previous
step, press
.
Or press
on the remote control.
Operating
iPod/ iPhone CONTROL
MODE
You can control on the unit and iPod /
iPhone.
 Press F on the unit to select CONTROL
and then set CONTROL to IPOD. Then
playback is paused. And you can control
on the unit and iPod / iPhone.
 While using the iPod/iPhone CONTROL
MODE, any functions are not available
on the unit.
 Sets CONTROL to HEAD UNIT to cancel
the iPod/ iPhone CONTROL MODE.
Compatible iPod / iPhone
models
 iPod classic
 iPod touch 4th generation
 iPhone 3G / 3GS / 4
We recommend that you use the
OS Version 4.2.1 or more.
“Made for iPod” and “Made for iPhone”
mean that an electronic accessory has
been designed to connect specifically
to iPod or iPhone respectively, and has
been certified by the developer to meet
Apple performance standards. Apple is
not responsible for the operation of this
device or its compliance with safety and
regulatory standards.
Please note that the use of this accessory
with iPod, iPhone may affect wireless
performance.
Before you start the pairing procedure,
make sure the Bluetooth wireless
technology is turned on in to your phone.
Refer to your phone’s user guide. Pairing
links your unit and phone with Bluetooth
wireless technology, and is required only
once for the initial setup. The process of
pairing may be different depend on the
phones. The PIN CODE is 1234.
ON PLAYER
1. Select the source to
BT
SRC
2. Search the phones
supported Bluetooth
wireless technology.
F
3. Select a phone you
want to connect.
Rotate the
volume knob
4. Connect the phone.
Press the
volume knob
Microphone
The microphone needs to be close to
and pointed toward the person speaking.
Install the microphone as shown below.
Microphone unit
, Note
If you power off the unit while talking
on the phone through the unit by
using the BT function, the function is
deactivated and you can talk on the
phone directly.
3
Operating
 iPod nano 6th generation
Connecting a Bluetooth
wireless technology
13
14
Operating
Using a Bluetooth wireless
technology
Listening to music of the
Bluetooth device
Disconnecting a phone
When your unit and the Bluetooth device
are pairing, Press SRC repeatedly to
select "BT". And play the music stored on
your Bluetooth device. Refer to the your
Bluetooth device’s user guide.
Press
F -> DISCONNECT -> YES
Answering and Ending a call
To answer a call, press CALL.
Bluetooth wireless technology
profiles information
To end a call, press END.
Rejecting a call
To reject a call, press
.
Audio transfer
3
It is possible to switch the audio
connection between your phone
equipped with Bluetooth wireless
technology and this unit.
Operating
1. Press CALL to answer the call.
2. Press and hold the volume knob. The
“PRIVATE” is displayed.
If the private mode is selected on the unit,
press and hold the volume knob to return
to the call to handsfree mode.
, Note
The call waiting function is not
supported. We do not guarantee any
errors due to use of the call waiting
function.
In order to use Bluetooth wireless
technology, devices must be able to
interpret certain profiles. This unit is
compatible with following profiles.
GAP (Generic Access Profile)
HFP (Hands Free Profile)
GAVDP (Generic Audio / Video Distribution
Profile)
A2DP (Advanced Audio Distribution
Profile)
AVRCP (Audio / Video Distribution Remote
Control Profile)
Adjusting the setting
1. Press F .
2. Rotate the volume knob to select an
item and press it.
3. Rotate the volume knob to set the
option and press it.
4. If you want to return to the previous
step, press
.
INFO
 NAME
Checks the name of this unit.
 ADDRESS
Checks the address.
 PINCODE
Changes the PIN code. Default is 1234.
CONNECT/ DISCONNECT
SETUP
 VISIBLE
Makes it is impossible to search this unit.
(SHOWN <-> HIDDEN)
 A-CON
Adjusts connection with automatically
or not. (ON <-> OFF)
 A-ANS
Adjusts answering automatically or not.
(MANUAL <-> AUTO)
 MIC_VOLUME
Adjusts microphone volume on the
phone from 1 to 5. While you are on the
phone with handsfree mode, press F
and rotate the volume knob to adjust
the microphone volume.
 CONNECT
When unit is not connected with
Bluetooth wireless technology, you can
search the phones available to connect.
 DISCONNECT
When unit is connected with Bluetooth
wireless technology, you can disconnect
the phone.
Operating
15
Using "LG CAR Remote"
application
You can control the unit by using the "LG
CAR Remote" application.
1. Search the “LG CAR Remote” application
and install it.
[Initial screen]
[Tuner screen]
You can select a source by pressing
"SOURCE".
3
2. Pairing links your unit and iPhone with
Bluetooth wireless technology. (Refer
to the page 13.)
3. Press and hold • APP.
When you run the “LG CAR Remote”
application, activating source is
displayed after initial screen. Then you
can control the unit on iPhone.
Operating
[Displays installed "LG CAR Remote"
application]
[Source Mode screen]
16
Operating
Phone compatibility list
Bluetooth list and manufacturing company applicable.
H : Handsfree
A : Audio Streming
Company
List
H
A
Company
List
H
A
Company
List
H
A
Company
List
H
A
LG
KM380
0
0
SAMSUNG
S8003 JET(8GB)
0
0
Nokia
E71
0
0
SONY
W595
0
0
KM900(Arena)
0
0
S8300 Ultra Touch
0
0
E75
0
0
ERICSSON
W705
0
0
KP500(Cookie)
0
0
B5722
0
N86
0
0
W980i
0
0
KS500
0
0
B7330 (Omnia Pro)
0
0
N97
0
0
Xperia-X1
0
0
KT520
0
0
C3303K (Champ)
0
0
C6
0
0
Vivaz
0
0
KT610
0
M5650U (Lindy)
0
0
E5
0
0
Xperia-X2
0
0
KU990
0
0
M8910 (Pixon12)
0
0
E52
0
0
Xperia-X10
0
0
3
GD900
0
0
S7350
0
0
N97-1
0
0
Operating
BL40 (New Chocolate)
0
S8500 (Wave)
0
0
N900
0
0
KM335
0
0
i5503 (Galaxy 5)
0
0
6710 (Navigator)
0
0
GD510 (POP)
0
0
0
0
0
i5700
(Galaxy Spica)
0
GD880
GM730
0
0
i7500 (Galaxy)
0
0
i9000 (Galaxy
S(16G))
0
0
T959
0
Galaxy Tab
0
GS500 (Cookie Plus)
0
0
GT505
0
0
GT540
0
0
GW305
0
0
GX500
0
0
0
Operating
17
Bluetooth list and manufacturing company applicable.
H : Handsfree
A : Audio Streming
Company
List
H
A
Company
List
H
A
APPLE
iPhone 3GS (16GB)
0
0
Motorola
XT701
0
0
iPhone 4 (16GB)
0
0
XT720 (MOTOROI)
0
0
0
Milestone Droid
0
0
i-Pad
“The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of
such marks by LG Electronics is under license. Other trademarks and trade names are those
of their respective owners.”
Bluetooth® wireless technology is a system which allows radio contact between electronic
devices within a max range of 10 meters.
Connecting individual devices under Bluetooth® wireless technology does not incur any
charges. A mobile phone with Bluetooth® wireless technology can be operated via the
Cascade if the connection was made via Bluetooth® wireless technology.
P750
0
0
HTC
Hero G3
0
0
Touch2
0
0
Operating condition for using a Bluetooth wireless
technology function
Legend
0
0
 Close windscreen.
Desire
0
0
 Turn off the air conditioner / heater.
Storm2 9550
0
0
 Stop the vehicle or drive at low speed.
Rim
, Note
 When the phone features <Bluetooth Power Save> function, you should make the
function turned on to maintain connection.
 When you switch the call mode from handsfree to phone, the connection may be
disconnected.
 Some phones don’t support Reject function.
 Low battery in phone may cause the problems.
 Make the call in a quiet location.
- There may be differences in call quality depending on phone type, road conditions
weather, etc.
- Using the phone while driving may cause unexpected accidents.
- The Bluetooth wireless technology function may not operate properly with certain
types of phones equipped with Bluetooth wireless technology.
3
Operating
ASUS
18
Troubleshooting
Troubleshooting
Symptoms
Cause
Solution
Power doesn't turned on.
Leads and connectors are not properly.
Confirm once more that all connections are correct.
The fuse is blown.
Rectify the problem that caused the fuse to blow, and then replace it. Be very sure
to install the correct fuse with the same rate.
Noise and other factors are causing the built in
microprocessor to operate incorrectly.
Turn the unit off and then on again.
Cables are not connected correctly.
Connect the cables correctly.
The unit doesn't operate.
No sound is heard.
4
Troubleshooting
There's audio skipping.
This unit is not firmly secured.
Secure this unit firmly.
Radio stations cannot be tuned in.
The signal strength of the stations is too weak. (When tuning
in with automatic tuning.)
Tuned in the stations manually.
No station has been preset or preset stations have been
cleared. (When tuning by scanning preset stations.)
Preset the stations.
iPod/ iPhone does not work.
Check whether iPod / iPhone is connected to the unit
correctly.
Connect it to the unit correctly.
The unit does not operate correctly
even when the appropriate remote
control buttons are pressed.
Battery power is low.
Load a new battery.
Appendix
Specifications
19
AUX
Frequency Response : 20 Hz to 20 kHz
General
S / N Ratio : 80 dB
Output Power : 53 W x 4 CH (Max.)
Distortion : 0.1 %
Power Source : DC 12 V
Channel Separation (1 kHz) : 45 dB
Speaker impedance : 4 Ω
Max Input Level (1 kHz) : 1.1 V
Ground System : Negative
Dimensions (W x H x D) : (178 x 50 x168)
mm (without Control Panel)
Net Weight : 1.10 kg
TUNER
FM Tuning Range :
87.5 MHz to 108.0 MHz
S / N Ratio : 55 dB
Distortion : 0.7 %
Usable Sensitivity : 12 dBμV
AM (MW) Tuning Range :
(520 to 1720) kHz or (522 to 1620) kHz
S / N Ratio : 50 dB
Distortion : 1.0 %
Usable Sensitivity : 28 dBμV
SD
Distortion : 0.1 %
Max capacity : 32 GB (SDHC standard)
Bluetooth
TX POWER 4 dBm
Version Bluetooth Specification 2.1 + EDR
Line OUT
Frequency Response : 20 Hz to 20 kHz
Output Voltage : 2 V (Max.)
Subwoofer
Frequency Response : 20 Hz to 120 Hz
Output Voltage : 2 V (Max.)
 Design and specifications are subject to
change without notice.
5
Appendix
Download PDF