LG | PW1510G | LG PW1510G Owner’s Manual

Owner's Manual
LG MiniBeam
DLP Projector
Please read the safety information carefully before using this product.
PW1510G
www.lg.com
P/NO : SAC37034643 (1804-REV03)
Copyright © 2017 LG Electronics Inc. All Rights Reserved.
2
LICENSES
LICENSES
Supported licenses may differ by model. For more information about
licenses, visit www.lg.com.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D
symbol are trademarks of Dolby
Laboratories.
This DivX Certified® device has passed
rigorous testing to ensure it plays DivX®
video.
To play purchased DivX movies, first
register your device at vod.divx.com. Find
your registration code in the DivX VOD
section of your device setup menu.
DivX Certified® to play DivX® video up to HD
1080p, including premium content.
DivX®, DivX Certified® and associated logos
are trademarks of DivX, LLC and are used
under license.
Covered by DivX Patents 7,295,673;
7,515,710; RE45,052; and others available
at [www.divx.com/patents]
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI logo
are trademarks or registered trademarks of
HDMI Licensing LLC in the United States
and other countries.

NOTE
• Image shown may differ from your projector.
• Your projector’s OSD (On Screen Display) may differ slightly from
that shown in this manual.
SAFETY PRECAUTIONS
3
SAFETY PRECAUTIONS
Please take note of the safety instructions to prevent any potential accident
or misuse of the projector.
• Safety precautions are given in two forms, i.e., WARNING and CAUTION
as detailed below.
WARNING Failure to follow the instructions may cause serious
injury and even death.
CAUTION Failure to follow the instructions may cause personal
injury or product damage.
• Read the owner's manual carefully and keep it on hand.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point
within an equilateral
triangle is intended to alert
the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
WARNING/CAUTION
-- TO REDUCE THE RISK
OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR
MOISTURE.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Indoor Installation
WARNING
• Do not use the projector outside
and do not expose the product
to any humidity or water.
--Since the product is not
waterproof, this may result in
a fire or electric shock.
• Do not place the projector in
direct sunlight or near heat
sources such as radiators, fires,
stoves, etc.
--This may result in fire.
• Do not place flammable
materials such as aerosols near
the projector.
--This may result in fire.
4
SAFETY PRECAUTIONS
• Do not allow children to cling to
or climb up to the projector.
-- This may cause the projector
to fall, causing injury or death.
• Do not install the product in a
place with no ventilation (e.g.,
on a bookshelf or in a closet) or
on a carpet or cushion.
--This may result in fire due
to the increase in internal
temperature.
• Do not place the product close
to sources of steam, oil or oil
mist, such as humidifiers and
kitchen counters.
--Failure to do so may result
in fire, electric shock, or
corrosion.
• Do not install the product onto
a wall or ceiling that is close to
sources of oil or oil mist.
--The product may be
damaged and fall, resulting in
serious injury.
• Do not place the projector where
it might be exposed to dust.
--This may result in fire.
• Do not use the projector in a
damp place such as a bathroom
where it is likely to get wet.
--This may result in fire or
electric shock.
• Do not allow a tablecloth or
curtain to block the air vent.
--This may result in fire due to
the increase in the internal
temperature.
• Ensure good ventilation around
the projector. The distance
between the projector and the
wall should be at least 30 cm.
--This will prevent fire due to
the increase in the internal
temperature.
CAUTION
• When placing the projector on a
table or shelf, be careful not to
put it near the edge.
--The projector could fall due
to balance problems, which
may cause personal injury or
damage to the product. Make
sure to use the projector
cabinet or stand that fits the
projector.
• When moving the projector,
make sure to switch it off and
remove the power plug and
cords.
--The power cord may be
damaged, resulting in fire or
electric shock.
• Do not place the projector on
an unstable or vibrating surface
such as a wobbly shelf or a
slope.
--It may fall and cause injury.
• Be careful not to tip the projector
over when connecting external
devices to the projector.
--This may cause personal
injury or damage to the
projector.
SAFETY PRECAUTIONS
Power
WARNING
• DISCONNECTING THE
DEVICE FROM THE MAIN
POWER
--The Power plug is the
disconnecting device. In case
of an emergency, the Power
Plug must remain readily
accessible.
• The grounding wire should be
connected. (Except for devices
which are not grounded.)
--Ensure that you connect the
grounding cable to avoid
electric shock.
If it is not possible to ground
the unit, have a qualified
electrician install a separate
circuit breaker.
Do not try to ground the
projector by connecting it to
telephone wires, lightning
rods, or gas pipes.
• The power plug should be
inserted fully into the power
outlet.
--An unstable connection may
cause a fire.
• Do not place heavy objects on
the power cord.
--This may result in fire or
electric shock.
5
• Never touch the power plug with
wet hands.
--This may result in electric
shock.
• Do not plug too many devices
into one multi-power outlet.
--This may result in fire due to
the power outlet overheating.
• Keep the AC adapter, power
plug, and the used power outlet
clean from dust or foreign
materials building up.
–– This may result in fire.
• If there is any smoke or a
burning smell from the projector
or AC adapter, stop using the
product immediately. Disconnect
the power cord from the power
outlet, and then contact the
customer service center.
–– This may result in fire.
• To turn off the main power,
remove the power plug, which
should be positioned so it is
easy to access for operation.
6
SAFETY PRECAUTIONS
CAUTION
• Always grab the plug to remove
the AC adapter or power cord.
–– Otherwise, this may result
in a fire or may damage the
product.
• Refrain from constantly bending
the power cord of the AC
adapter.
–– If the power cord is bent
excessively for a long period
of time, the cord may break
inside. This may result in a
fire or electric shock.
• Ensure the power cord and plug
are not damaged, modified,
severely bent, twisted, pulled,
sandwiched or hot. Do not use
the product if the power outlet
is loose.
–– This may result in fire or
electric shock.
• Keep the power cord away from
heating devices.
--The wire's sheath may melt,
which may result in fire or
electric shock.
• Place the projector where
people will not trip over or step
on the power cord to protect the
power cord and plug from any
damage.
--This may result in fire or
electric shock.
• Do not turn the projector on or
off by plugging in the power plug
or unplugging it from the power
outlet. (Do not use the power
plug as a switch.)
--This may result in electric
shock or damage to the
product.
• Do not insert a conductor
into the other side of the wall
outlet while the power plug is
inserted into the wall outlet.
In addition, do not touch the
power plug immediately after it
is disconnected from the wall
outlet.
--This may result in electric
shock.
• Only use the official power cord
provided by LG Electronics. Do
not use other power cords.
--This may result in fire or
electric shock.
• If any water or foreign materials
have gone into the AC adapter,
power cord, or the interior of the
projector, turn off the projector
by pressing the power button.
Remove all the cables, and then
contact the customer service
center.
–– This may result in fire or
electric shock.
SAFETY PRECAUTIONS
• The surface of the AC adapter is
hot. Keep the AC adapter out of
the reach of children and avoid
touching it during use.
• Never disassemble the power
supply devices (AC adapter/
power cord, etc.).
–– This may damage the power
cord and result in a fire or
electric shock.
• Connect the AC adapter and the
power cord firmly.
–– Not doing so may result in a
product failure or fire.
• Do not place heavy objects
or put pressure on the power
cord and AC adapter and avoid
damage.
–– This may result in a fire or
may damage the product.
• Always use the AC adapter
provided or any AC adapters
approved and certified by LG
Electronics.
–– Any other AC adapter
connected may result in the
screen flickering.
7
When in Use
WARNING
• Do not place anything
containing liquid on top of the
projector such as a vase, flower
pot, cup, cosmetics, medicine,
or ornaments, candles, etc.
--This may result in fire or
electric shock, or cause injury
due to falling.
• In the event that there is a
heavy impact or the cabinet is
damaged, switch it off, unplug
it from the power outlet and
contact an authorized service
center.
--This may result in electric
shock.
• Do not insert pieces of metal
such as coins, hairpins, or metal
debris, nor flammable materials
such as paper or matches into
the projector.
--This is to prevent electric
shock or fire.
• Make sure that a child does
not swallow the batteries when
you replace the old remote
control batteries with new ones.
Keep batteries out of reach of
children.
--If a child swallows a battery,
consult a doctor immediately.
8
SAFETY PRECAUTIONS
• Never open any cover on the
projector.
--There is a high risk of electric
shock.
• Do not look directly into the lens
when the projector is in use.
--The bright light may damage
your eyes.
• When the lamp is on or has just
been turned off, avoid touching
the air vent or lamp, because
these will be very hot.
• If there is a gas leak in the
room with the projector, do not
touch the projector or power
outlet. Open the windows for
ventilation.
--Sparks may cause fire or
burns.
• Unplug the power cord from the
outlet during a lightning storm.
--This will prevent shock or
damage to the projector.
• Do not use the projector near
electronic devices that generate
a strong magnetic field.
• Keep the plastic film used for
packaging the projector out of
the reach of children.
–– If not handled safely, it can
cause suffocation.
• Do not keep your hand on the
projector for a long time when it
is running.
• When you play a game by
connecting a game console to
a projector, it is recommended
that you maintain a distance
of more than four times the
diagonal length of the screen.
--Make sure that the
connecting cable is long
enough. Otherwise, the
product may fall causing
personal injury or damage to
the product.
• Do not place the projector or its
remote control with battery in
an extremely high temperature
environment.
--This may result in fire.
• Do not use 3D glasses if you do
not watch 3D.
SAFETY PRECAUTIONS
CAUTION
• Do not place heavy objects on
the projector.
--It may fall down and cause
personal injury.
• Be careful not to allow any
impact to the lens during
transport.
• Do not touch the lens of the
projector.
--The lens may be damaged.
• Do not use any sharp tools on
the projector such as a knife
or hammer, because this may
damage the casing.
• In the event that no image
appears on the screen or no
sound is heard, stop using
the projector. Switch off the
projector, unplug it from the
power outlet and contact our
service center.
--This may result in fire or
electric shock.
• Do not drop anything onto the
projector or allow anything to
bang into the projector.
--This may cause damage
to the projector or personal
injury.
• It is recommended that you
maintain a distance of more
than 5 to 7 times the diagonal
length of the screen.
–– If you watch the screen at
a close distance for a long
time, your eye sight may
become worse.
9
• Do not block the light beam
emitted from the projector using
a book or other object.
--Lengthy exposure to the
projector beam may result in
fire. In addition, the lens may
be overheated and damaged
by the reflected heat. Disable
the AV function to stop
projection temporarily or turn
off the power.
• Do not start the projector with
the volume turned up high.
--High volume may damage
hearing.
• Do not use high voltage
electrical equipment near the
projector, (e.g., a bug zapper).
This may result in product
malfunction.
• Do not insert your finger into the
air vent (inflow/outflow vents).
--This may cause injury or a
product malfunction.
10
SAFETY PRECAUTIONS
Cleaning
WARNING
• Do not spray the projector with
water when cleaning. Make sure
water does not flow into the
projector.
--This may result in fire or
electric shock.
• When there is smoke or a
strange smell coming out from
the projector or a foreign object
falls into the projector, please
switch it off and unplug it from
the power outlet and contact our
service center.
--Otherwise, this may result in
fire or electric shock.
• Use air spray, a soft cloth, or
a cotton swab moistened with
a lens cleaning chemical or
alcohol to remove dust or stains
on the front projection lens.
CAUTION
• Contact your seller or our
service center once a year to
clean the internal parts of the
projector.
-- If you do not clean the
projector for a long period of
time, dust will accumulate,
which may result in fire or
damage to the projector.
• When cleaning plastic parts
such as the projector case,
unplug the power first and wipe
with a soft cloth. Do not spray
with water or wipe with a wet
cloth. Never use glass cleaner,
automobile or industrial polish,
abrasives, wax, benzene, or
alcohol as these can damage the
projector.
-- This can result in fire, electric
shock or cause damage to
the product (deformation and
corrosion).
• Remove the plug from the outlet
before cleaning the product.
-- Otherwise, this may result in
electric shock.
SAFETY PRECAUTIONS
Others
WARNING
• Some users may experience
a seizure or other abnormal
symptoms when they are
exposed to a flashing light or
particular patterns from a video
game.
• When you go out, place the
projector out of reach of
animals, and remove the power
plug from the wall outlet.
--Using a damaged power cord
may result in short circuit
or fire.
• Do not use the projector near
high-precision electronic devices
or those that transmit weak
radio signal.
--This may affect the operation
of the product, causing an
accident.
• Only a qualified technician
can disassemble or modify
the projector. For diagnosis,
adjustment, or repair, contact
your seller or our service center.
--This may result in fire or
electric shock.
• Proper ventilation required, do
not block airflow around unit.
Doing so can cause injury and
internal overheating.
11
• Do not touch the lens; doing so
can result in burns or damage
to lens. Lens and unit may be
HOT during and immediately
after use. Use caution when
handling unit, allowing for proper
cool down.
• Only use a grounded electrical
outlet. (Except for devices which
are not grounded.)
• Do not insert anything into or
cover up the exhaust vents.
--This may result in fire or
electric shock.
• Follow all maintenance
guidelines for optimal use;
service only at an authorized
service center.
• Keep the batteries and remote
out of reach of children.
–– This will prevent personal
injury or damage to the
product.
12
SAFETY PRECAUTIONS
CAUTION
• Do not use or store the projector
outdoors for long periods of
time.
• Do not mix new batteries with
old ones.
-- Burst or leaking batteries may
result in damage or injury.
• Be sure to unplug if the projector
is not to be used for a long
period.
-- Accumulated dust may result
in fire or electric shock due to
overheating, ignition, or poor
insulation.
• Only use the specified type of
battery.
-- Burst or leaking batteries may
result in damage or injury.
• Make sure you use the same
type of battery when replacing.
(Battery type: CR2032 / 3 V)
–– In the case of a battery
contact failure, the battery
may drain quickly or the
remote control may not work
properly.
• Dispose of used batteries
properly.
-- This may result in explosion
or fire. The correct method of
disposal may vary depending
on your country or region.
• Do not throw or disassemble the
battery.
-- This may result in fire or
explosion due to damage to
the battery.
• Store batteries away from
metallic objects, such as keys
and paper clips.
-- Excess current may cause a
rapid increase in temperature,
resulting in fire or burns.
• Do not store the batteries near
any heat source, such as a
heater.
-- This may result in fire or
damage to the product.
• Do not store batteries at
temperatures higher than 60 °C
or in high humidity.
-- This may result in explosion
or fire.
• Make sure that the battery is
installed correctly.
-- This may prevent explosion
or fire.
• Incorrect battery replacement
may cause fire.
• Batteries: Store the accessories
(battery, etc.) in a safe location
out of the reach of children.

Risk Group 2
CAUTION Possibly hazardous
optical radiation emitted from this
product. Do not stare at operating
lamp. May be harmful to the eye.
CONTENTS
13
CONTENTS
LICENSES
2
SAFETY PRECAUTIONS 3
Additional Options
32
--Adjusting Aspect Ratio
32
--Using the Keystone Function
33
--Changing Input Device 34
--Blank Function
36
PREPARATION
15
Accessories
15
Optional Extras
17
Using the Quick Menu
37
Parts and Components
18
Using the Joystick Button
--Basic Functions
--Adjusting the Menu
20
20
21
ENTERTAINMENT
38
Using SCREEN SHARE
38
Projector Status Indicators 21
Installation
22
--Installation Precautions 22
--Projection Distance per
Screen Size
23
--How to Install the Projector
On a Tripod
25
--Kensington Security System
26
REMOTE CONTROL
27
USING THE PROJECTOR30
Watching Projector
30
--Turning on the Projector 30
--Focus of the Screen Image
31
--Watching With the Projector
31
Setting Up Bluetooth on the
Projector
39
--Searching for Bluetooth
Devices and Connecting 40
--Connecting, Disconnecting,
or Deleting Bluetooth
Devices in the List of
registered devices
42
--Adjusting AV Sync. Adjust 43
MY MEDIA
44
Before Using
44
--Connecting a USB Device44
--Removing a USB Device 44
To Use My Media
--Watching the Videos
--Viewing the Photos
--Listening to Music
--Viewing Files
46
50
56
60
64
14
CONTENTS
3D FUNCTION
68
While Watching 3D
68
Requirements for Watching 3D
Images
72
--Using the DLP-LINK (DLPReady) Type Glasses
73
To view 3D images
--Supported 3D Mode
73
74
CUSTOMIZING SETTINGS 76
SETTINGS
76
PICTURE Settings
77
AUDIO Settings
84
TIME Settings
86
WIRELESS Settings
87
OPTION 1 Settings
89
OPTION 2 Settings
90
CONNECTING DEVICES 92
Connecting to HD Receiver,
DVD, VCR Player, or External
Devices
93
--HDMI Connection
93
--HDMI to DVI Connection 93
--Composite (AV) Connection
94
--Component Connection 94
Connecting a PC
--HDMI Connection
--HDMI to DVI Connection
--RGB Connection
95
95
95
96
Connecting a Laptop
--HDMI Connection
97
97
Connecting to Headphones 98
Using the Mirroring Function
of a Mobile Phone
99
--MHL/Slimport Connection 99
MAINTENANCE
100
Cleaning
100
--Cleaning the Lens
100
--Cleaning the Projector Case
100
SPECIFICATIONS
101
KEY CODES
105
EXTERNAL CONTROL
DEVICE SETUP
107
Communication Parameters
108
Command reference list
109
Transmission / Receiving
Protocol
110
SYMBOLS
121
PREPARATION
PREPARATION
The pictures may differ slightly from the actual product.
Accessories
Accessories included with the projector are show below.
Accessories are subject to change without prior notice.
New accessories may be added or old ones removed.
219'4
+0276
/76'
2#)'
81.7/'
#761
$.#01-
':+6
ꕣ
5'66+0)5
3/'07
56+..
4#6+1
*'.2
-';5
&
75$
-';5
.4
Remote Control,
Lithium Battery
(CR2032 / 3 V)
Owner's Manual
AC-DC Adaptor
Composite Gender
Power cord
Pouch
15
16
PREPARATION
• When connecting an HDMI or USB
cable, or connecting a USB flash drive
to the HDMI or USB port, use a product
that has a width of 18 mm or less and
a height of 10 mm or less. If the USB
cable or USB flash drive does not fit
the USB ports of the projector, use an
extension cable that supports USB 2.0.
• Use a certified cable with the HDMI logo attached.
• If you do not use a certified HDMI cable, the screen may not display or a
connection error may occur. (Recommended HDMI cable types)
--High-Speed HDMI®/™ Cable
--High-Speed HDMI®/™ Cable with Ethernet
PREPARATION
17
Optional Extras
To purchase optional accessories, visit an electronics store or online
shopping site or contact the retail store where you purchased the product.
Optional accessories are subject to change without prior notice.
Projection Screen
Tripod
HDMI Cable
Video Cable
Audio Cable
3D glasses
(DLP-LINK or DLP
Ready Type)
RGB to Component
cable
Component Cable
MHL or Slimport cable
Computer Cable
18
PREPARATION
Parts and Components
This projector is manufactured using high-precision technology. You may,
however, see tiny black dots and/or bright colored dots (red, blue, or
green) that continuously appear on the projector screen. This is a normal
result of the manufacturing process and does not indicate a malfunction.
Joystick button
Speaker
Vent1)
Speaker
Vent1)
Lens2)
Focus ring
1)Due to the high temperature of vent area, do not get close to the vent area.
2)Do not touch the lens when using the projector. The lens may be damaged.
PREPARATION
2
1
RS-232C IN
1
RS-232C IN Port
2
(USB Port)
3
4
5
Port
RGB IN Port
(Headphone Port)
6
AV IN Port
7
DC IN Port
3
4
5 6
7
19
20
PREPARATION
Using the Joystick Button
You can operate the projector by pressing the button or moving the joystick
left, right, up, or down.
Basic Functions
Power On
When the projector is turned off, place
your finger on the joystick button,
press it once, and release it.
Power Off
When the projector is turned on, place
your finger on the joystick button,
press it once for a few seconds, and
release it. (However, if the menu
button is on the screen, pressing and
holding the joystick button will let you
exit the menu.)
Volume
Control
Place your finger over the joystick
button and move it left or right. You
can adjust the volume level.
Up/Down/
Left/Right
If you move the joystick up, down, left,
or right, you can move the cursor to
select the menu items.
NOTE
• Move the joystick button up, down, left, or right. Be careful not to
press the joystick button. If you press the button while moving the
joystick, the volume control may not work, and the cursor may not
move.
PREPARATION
21
Adjusting the Menu
When the projector is turned on, press the joystick button one time.
You can adjust the menu items ( ,
, , ) moving the joystick
button left, right, up, or down. Move to the desired menu item, and then
press the joystick button once to select it.
Close
Projector off
Turns the power off.
Input List
Changes the input source.
Close
Clears on-screen displays and
returns to projector viewing.
Settings
Displays the Settings menu.
Projector Status Indicators
LED Power Indicator
LED Power Indicator
Red
Power standby state
Off
The projector is operating with the power on.
22
PREPARATION
Installation
Installation Precautions
• Place the projector in a wellventilated environment.
--To prevent internal
overheating, install the
projector in a well-ventilated
place. Do not place anything
near the projector that may
block its air vents. If the
air vents are blocked, the
internal temperature of the
projector will increase.
--Do not place the projector
on a carpet or rug. If the
projector's inlet vent is on
the bottom, be careful not to
block the vent and always
use the projector on a solid,
level surface.
--Be sure to prevent foreign
objects such as paper debris
from entering the projector.
--Leave an adequate open
area (30 cm or more) around
the projector.
• Do not place the projector in a
hot, cool, or humid environment.
• Do not place the projector in a
place where it will easily attract
dust.
--This may result in fire.
• Never open any cover on the
projector. There is a high risk of
electric shock.
• The projector is manufactured
using high-precision technology.
You may, however, see
tiny black dots and/or bright
colored dots (red, blue or
green) that continuously
appear on the projector screen.
This is a normal result of the
manufacturing process and
does not indicate a malfunction.
• The remote control may not
work in an environment where
a lamp equipped with electronic
ballasts or a three-wavelength
fluorescent lamp is installed.
Replace the lamp with an
international standard lamp
for the remote control to work
normally.
• To install to the ceiling, attach
the ceiling-type bracket to
the projector with M4 x 8 mm
screws.
PREPARATION
23
Projection Distance per Screen Size
1 Place the projector on a sturdy, level surface, together with the PC or
audio/video source.
2 Place the projector an appropriate distance away from the screen. The
distance between the projector and the screen determines the actual
size of the image.
3 Position the projector so that the lens is at a right angle to the screen.
If the projector is not at a right angle, the projected image will look
distorted. To correct the distortion, use the keystone function.
(See page 33.)
4 Connect the power cord of the projector and the connected device to
the wall outlet.
Ratio of upward projection: 100 %
Y/2
Screen
Y/2
X/2
Projection Distance (D)
Screen Width (Y)
X/2
Screen Height (X)
Screen
Projection Distance (D)
24
PREPARATION
16:10 Ratio
Screen Size (mm)
Screen Width (Y) (mm)
Screen Height (X) (mm)
Projection
Distance (D)
(mm)
635
762
889
1016
1143
1270
1397
1524
1651
1778
1905
2032
2159
2286
2413
2540
539
646
754
862
969
1077
1185
1292
1400
1508
1615
1723
1831
1938
2046
2154
337
404
471
538
606
673
741
808
875
943
1010
1077
1145
1212
1279
1347
748
902
1056
1210
1366
1520
1674
1828
1983
2137
2291
2445
2601
2755
2909
3063
PREPARATION
25
How to Install the Projector On a Tripod
• You can install the projector using a camera tripod.
• As shown below, you can mount the projector instead of a camera on
the tripod.
• When stabilizing the tripod, we recommend using a locking bolt of
standard size 4.5 mm or less. The maximum size allowed for the locking
bolt is 5.5 mm. (If it is longer than the maximum allowed size, it may
damage the projector.)
Bottom side of the
projector
Bolt used to
attach the
projector
⇒
+
The projector is
connected to this part.

Tripod
CAUTION
• If you are using a tripod, be careful not to apply external force to the
tripod. Doing so may damage the projector.
• Do not place the tripod on an unstable surface.
• Be sure to use a tripod with a maximum load capacity of 3 kg or
more.
• To use the projector safely, position the tripod legs so that they are
as wide and stable as possible and be sure to securely attach the
projector to the tripod.
26
PREPARATION
Kensington Security System
• This projector has a Kensington Security Standard connector as an
anti-theft mechanism. Connect a Kensington Security System cable as
shown below.
• For more information on installation and use of the Kensington Security
System, refer to the user’s guide provided with the Kensington Security
System.
• The Kensington Security System is an optional accessory.
• What is Kensington?
Kensington is a company that provides safety systems for laptops and
other electronic devices. Website: http://www.kensington.com
27
REMOTE CONTROL
REMOTE CONTROL
Open the battery cover on the back of the remote
control and insert the batteries which are specified
in the battery room with
poles pointing in the
correct direction. Use new batteries.
①
②
POWER
Turns the projector on or off.
219'4
+0276
/76'
2#)'
81.7/'
MUTE
Mutes the sound of the projector.
INPUT
Changes the input source.
VOLUME +, Adjusts the volume level.
PAGE
Moves to the previous/next page.
,
#761
$.#01-
':+6
ꕣ
5'66+0)5
3/'07
56+..
4#6+1
*'.2
-';5
&
75$
-';5
.4
AUTO
Automatically adjusts the RGB-PC input
image.
Up/Down/Left/Right buttons
Sets the function or moves the cursor.
OK
Shows the current mode and saves
changes to the settings.
BLANK
Displays a blank screen.
EXIT
Exits the menu.
Returns to the previous screen.
SETTINGS
Displays or closes the Settings menu.
Q.MENU
Enters the quick menu.
28
REMOTE CONTROL
219'4
+0276
/76'
2#)'
81.7/'
#761
$.#01-
':+6
ꕣ
5'66+0)5
3/'07
56+..
4#6+1
*'.2
-';5
&
75$
-';5
.4
STILL
Freezes the moving image.
(Available in any mode other than USB
mode.)
RATIO
Changes the aspect ratio of the screen
per pressing of the button.
USB
Accesses USB mode.
HELP
Enables the self-diagnosis.
KEY.S ▲, ▼
Adjusts the Keystone function.
Playback control buttons
Controls playback of MY MEDIA.
Color buttons
Sets detailed settings or gesture for each
menu.
3D
Shows 3D images.
L/R
Switches left and right in 3D mode.
REMOTE CONTROL
NOTE
• When using the remote control, the optimal
operation range is 6 meters or less (left/right)
and within a 30 degree arc of the remote
control IR receiver.
30° 30°
• If a cable is connected to the back port, the
optimal operating range is 3 meters or less
(left/right) and within a 30 degree arc of the
remote control IR receiver.
• For seamless operation, do not block the IR
receiver.
• When you carry the remote control in the portable bag, make
sure that the buttons on the remote control are not pressed by the
projector, cables, documents, or any other accessories in the bag.
Otherwise, it may significantly reduce the battery life.
RS-232C IN
219'4
+0276
/76'
2#)'
81.7/'
#761
$.#0-
1-
':+6
ꕣ
5'66+0)5
3/'07
56+..
4#6+1
*'.2
-';5
&
75$
-';5
.4
29
30
USING THE PROJECTOR
USING THE PROJECTOR
Watching Projector
Turning on the Projector
The menu screen display in this owner's manual is an example to help
users understand how to operate the product and may look different from
the actual screen.
1 Connect the power cord correctly.
2 After waiting for a moment, press the POWER button on the remote
control or the joystick button.
3 In the Language Selection screen, select a language.
WELCOME!
Language
Thank you for choosing LG
Confirm
4 In the Mode Setting screen, select the setting mode you want.
Mode Setting
Selecting the environment.
Choose the setting mode you want.
Select [Standard] to use this Projector at home. To use this
Projector at store, select [Store Demo].
Standard
Store Demo
Demo Mode
Off
Previous
Confirm
*S
tore Demo is used when displaying the product in-store. The picture
mode is automatically reset after a certain period of time. You can
select Standard to use the product at home.
5 Select an input signal by using the INPUT button on the remote control.
USING THE PROJECTOR
31
Focus of the Screen Image
When an image appears on the screen, check if it is in focus and fits the
screen properly.
Adjust the focus of the image by rotating the Focus Ring to the left or right.
Make sure the product does not move when adjusting the focus.
Focus Ring
Watching With the Projector
1 When in standby mode, press the POWER button to turn the projector
on.
2 Press the INPUT button and select the input signal you want.
3 Control the projector using the following buttons while watching
projector.
Button
Description
VOLUME +, -
Adjusts the volume level.
MUTE
Mutes all sounds.
Q.MENU
Accesses the quick menu.
RATIO
Resizes an image.
KEY.S ▲, ▼
Adjusts Keystone.
4 To turn the projector off, press the POWER button.
32
USING THE PROJECTOR
Additional Options
Adjusting Aspect Ratio
Resize an image to view at its optimal size by pressing RATIO while you
are using the projector.
NOTE
• Available picture size may differ depending on the input signal.
• You can also use the Q.MENU or SETTINGS button.
Menu
Description
16:9
Resizes images to the 16:9 ratio.
Full
Changes to the full screen regardless of the aspect ratio.
Just Scan
Displays video images in the original size without
removing parts of the edge of the image.
• If you select Just Scan, you may see image noise at
the edge or edges of the screen.
Set By
Program
Displays images in the same aspect ratio as the original
image.
4:3
Resizes images to the previous standard 4:3.
Zoom
Resizes the image to fit the screen width. The top and
bottom parts of the image may be cut off.
• Press the
or
button to zoom in or out of the
image.
• Press the
or
button to move the image.
Cinema
Zoom 1
Formats an image to the cinemascope ratio, 2.35:1.
It ranges from 1 to 16.
• Press the
or
button to zoom in or out of the
image.
• Press the
or
button to move the image.
• If you enlarge or reduce an image, the image may be
distorted.
USING THE PROJECTOR
33
Using the Keystone Function
To prevent the screen image from becoming trapezoidal, Keystone
adjusts the top and bottom width of the image if the projector is not set up
at a right angle to the screen.
Because the Keystone function may cause inferior screen image quality,
use this function only when it is not possible to set up the projector at an
optimal angle.
• Keystone
0
◀ -
+ ▶
OK
1 Press the KEY.S
,or KEY.S, button to adjust the picture.
• Keystone can be adjusted from -40 to 40.
2 Press the OK button when done.
34
USING THE PROJECTOR
Changing Input Device
To select an external input
Selects external input.
The illustration of the menu may differ from the actual screen on the
product.
• Press the INPUT button on the remote control to display the input
selection screen.
--Connected inputs are displayed first. However, AV / Component /
SCREEN SHARE input is always activated.
• Select an input signal using the remote control's INPUT button to
connect the projector to the desired input.
You can use the
, or
button to switch between all the input modes.
Input List
AV

ꔂ Move ꔉ OK
Component
SCREEN SHARE
USB
Input Label
RGB-PC
HDMI
Exit
USING THE PROJECTOR
Selecting an Input Label
Displays which devices are connected to which input ports.
Input Label
AV
Component
RGB-PC
HDMI
Close
1 Press the INPUT button on the remote control to display the input
selection screen.
2 Press the Red button.
3 Use the or button to scroll to one of the input sources.
4 Use the or button to select one of the input labels.
35
36
USING THE PROJECTOR
Blank Function
Using the Blank Function
This function may be effective when you need to draw attention during a
meeting or training.
1 Press the BLANK button, and the screen is covered by the
background color. You can change the background color by referring
to Selecting a Blank Image.
2 Press any button to clear the blank function. To cover the screen
temporarily, press the BLANK button on the remote control. Do not
block the lens with any object while the projector is running. It may
become overheated and deformed or even cause a fire.
Selecting a Blank Image
1 Press the SETTINGS button.
2 Press the , , , or buttons to select OPTION 2 and press
the OK button.
3 Press the
button.
4 Press the
,
buttons to select Blank Image and press the OK
or
button to move to the setting or option you want
and press the OK button.
USING THE PROJECTOR
Using the Quick Menu
You can easily customize your frequently used menus.
1 Press the Q.MENU button.
2 Press the or button to select a menu and press OK button.
Menu
Description
Aspect Ratio
Resizes the picture.
PJT Mode
Turns the projected image upside down or flips it
horizontally.
Picture Mode
Changes the picture mode.
Sound Mode
Sets the sound mode.
Sleep Timer
Sets the projector to be turned off at the specified
time.
Clear Voice II
Makes the voice from the projector crisp and clear.
Energy
Saving
Reduces power consumption by adjusting peak
screen brightness.
USB Device
Allows you to remove a connected USB device in a
safe manner.
(The menu is displayed only when the USB device is
connected.)
3 Press the
or
button to scroll through the following menus.
37
38
ENTERTAINMENT
ENTERTAINMENT
Using SCREEN SHARE
1 Set the external input of the projector to SCREEN SHARE.
2 Enable related SCREEN SHARE function on the device you wish to
connect.
3 Connect the projector from the search list on the device you wish to
connect. (When you connect the projector to your laptop, input the PIN
code shown on your display. The request for a PIN will be shown only
at the initial connection.)
4 If the desired device accepts the request, SCREEN SHARE will be
started.
CAUTION
• Windows 7 / 8 / 8.1 are compatible with SCREEN SHARE. However,
other versions of Windows, and some other operating systems, may
not be compatible with SCREEN SHARE.
• Ice Cream Sandwich, Jellybean, KitKat, and Lollypop versions of
LG’s Android devices are guaranteed to be compatible.
• When connecting via SCREEN SHARE, place the device close to
the projector.
• The response rate and image quality may vary depending upon the
user’s environment.
• For more information on the device you want to connect to, refer to
its owner’s manual.
• Certain Windows 8.1 laptops may have difficulty in reconnecting
when initializing the device information during a wireless connection.
In this case, it is recommended that you remove the registered
device and reconnect.
ENTERTAINMENT
39
Setting Up Bluetooth on the Projector
This option is used to output sound from the projector through Bluetooth
audio devices.
• Press the SETTINGS button on the remote control, and then set
Bluetooth to On in the WIRELESS menu.
NOTE
• The devices that can be connected are as follows: LG BTS1, LG
HBS-700, LG HBS-730, LG HBS-800 (Models available for purchase
may vary by region.)
• Products from other manufacturers may not be compatible.
• You can use the remote control to adjust the volume of the
connected device.
• When connecting devices wirelessly, if the device connection fails,
check that the device is connected to a power supply and also check
that the Bluetooth audio device is operating properly.
• If Bluetooth is turned on, the projector will automatically connect
to the last connected Bluetooth device when the projector powers
on. (Be sure to check that the last connected Bluetooth device is
powered on as well.)
• This projector does not support the LG TV Sound Sync feature. To
use products that support the LG TV Sound Sync feature, use the
general Bluetooth mode instead of the LG TV mode.
• The Bluetooth function is to connect the product to Bluetooth
speakers or Bluetooth headset. You cannot connect the product to a
mobile phone through the Bluetooth function.
40
ENTERTAINMENT
Searching for Bluetooth Devices and Connecting
Go to SETTINGS → WIRELESS → Search Device to search for nearby
Bluetooth audio devices and then connect any detected devices to the
projector.
(If the device name is longer than 20 characters, no more than 20 will be
displayed.)
1 Set the Bluetooth device to pairing mode and then select Search
Device.
• Select Stop searching to view the devices detected so far.
• If the device has not been detected, check that the device is powered
on and in pairing mode.
• The time it takes to search for devices may vary according to the
signal strength and the number of devices.
WIRELESS
ꔂ Move ꔉ OK
•• SCREEN SHARE
: [PJTR][LG]PW1510[0000]
•• Group
•• Channel
•• Bluetooth
: On
•• Search Device
•• List of registered devices
•• AV Sync. Adjust
ENTERTAINMENT
41
2 When the search is complete, you can select a Bluetooth device and
connect to it.
• You can stop the connection process immediately by selecting Stop
searching.
• The time it takes to connect to a device may vary according to the
signal strength and the number of devices.
Search Device
List
Search Device
Searching...
Please wait.
List
Search complete
HBS-700
Press OK(ꔉ) to connect the device.
Stop searching
Close
Re-search
Close
3 When a Bluetooth device is connected, you will hear sound from the
projector through the connected device.
• The connected Bluetooth device will be added automatically to the
List of registered devices. Once registered, Bluetooth devices can
be connected simply by selecting them from the List of registered
devices without having to search for them.
• Connected devices can only be disconnected from SETTINGS →
WIRELESS → List of registered devices.
42
ENTERTAINMENT
Connecting, Disconnecting, or Deleting Bluetooth
Devices in the List of registered devices
In SETTINGS → WIRELESS → List of registered devices, Bluetooth
devices are shown in the order that they were connected, and the same
devices can be reconnected simply by selecting them without having to
search for them again.
List of registered devices
List
HBS-700
Delete
Press OK(ꔉ) to connect the device.
Delete All
Close
Connecting
Select a Bluetooth device from the List of registered devices to connect
to it.
• The registered Bluetooth device will attempt to connect automatically
depending on the characteristics of the device. (Refer to the manual for
the Bluetooth device.)
• You can stop the connection process immediately by selecting Stop.
• The time it takes to connect to a device may vary according to the signal
strength and the number of devices.
Disconnecting
Select Disconnect to disconnect the device.
• You can only disconnect a device from the List of registered devices.
ENTERTAINMENT
43
Deleting
Select Delete Marked or Delete All to delete any registered devices.
• Delete Marked: Press the red button in List of registered devices to
delete the selected device.
• Delete All: Select Delete All in List of registered devices to delete all
of the registered devices.
Adjusting AV Sync. Adjust
When a Bluetooth device is connected, go to SETTINGS → WIRELESS
→ AV Sync. Adjust to adjust the synchronization between the video and
the Bluetooth headset sound.
• AV Sync. Adjust
10 ◀
▶
OK
• This feature is only available when a Bluetooth device is connected.
• Audio sync may vary by manufacturer.
• When playing video from a connected USB drive, AV Sync. Adjust can
also be adjusted using the Set Audio. menu.
44
MY MEDIA
MY MEDIA
Before Using
Connecting a USB Device
Connect a USB device (external
HDD, USB memory) to the USB port
of projector to enjoy the content files
stored in the USB device with your
projector. You cannot write or delete
data in the USB device. Connect a
USB flash drive as shown below.
USB Flash
Drive
Removing a USB Device
1 Click the Q.MENU button.
2 Use the or button to move to USB Device and press the OK
button.
3 Select a USB to remove. Wait for confirmation that the USB device has
stopped before removing the USB.

NOTE
• If detached early, an error may occur on the projector or the USB
storage device.
• Once a USB device has been selected for removal, it can no longer
be read. Remove the USB storage device and then re-connect it.
MY MEDIA
45
Tips for using a USB device
• If the USB storage device has a built-in auto recognition program or uses
its own driver, it may not work.
• Some USB storage devices may not work or may work incorrectly.
• If you use a USB extension cable, the USB device may not be
recognized or may not work properly.
• Use only USB storage devices formatted with the Windows FAT32 or
NTFS file system.
• For external USB HDDs, it is recommended that you use devices with a
rated voltage of less than 5 V and a rated current of less than 500 mA.
• It is recommended to use a Hard Disk Drive with its own power supply.
(If the power being supplied is not sufficient, the USB storage device
may not be detected correctly.) Note, a USB Hub is not supported.
• It is recommended that you use USB flash drives of 32 GB or less and
USB HDDs of 2 TB or less.
• If a USB HDD with power-saving function does not work properly, turn
the power off and on. For more information, refer to the user manual of
the USB HDD.
• Data in USB storage device can be damaged so be sure to back
up important files to other devices. Data maintenance is the user's
responsibility and the manufacturer is not responsible for data loss.
46
MY MEDIA
To Use My Media
1 Press the SETTINGS button on the remote control.
2 Select MY MEDIA.
Select desired file from the list. Watch the chosen file.
Sets play related settings by checking option during disk playback.
My Media supporting file
• Maximum data transmission rate: 20 Mbps (Mega bit per second)
• External supported subtitle formats: *.smi, *.srt, *.sub (MicroDVD,
SubViewer 1.0/2.0), *.ass, *.ssa, *.txt (TMPlayer), *.psb (PowerDivX)
• Internal supported subtitle formats: SRT/ASS/SSA (Supports internal
subtitles generated from DivX6)
MY MEDIA
Video Supported Codec
Maximum: 1920 x 1080 @ 30p (only Motion JPEG 640 x 480 @ 30p)
Extension
.asf
.wmv
.divx
.avi
.mp4
.m4v
.mov
.mkv
.ts
.trp
.tp
.mts
.m2ts
.vob
.mpg
.mpeg
Codec
Video
VC-1 Advanced Profile, VC-1 Simple and Main
Profiles
Audio
WMA Standard, WMA 9 Professional
Video
DivX3.11, DivX4, DivX5, DivX6, XVID,
H.264/AVC
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3),
Dolby Digital
Video
H.264/AVC, MPEG-4 Part 2
Audio
AAC
Video
H.264/AVC
Audio
HE-AAC, Dolby Digital
Video
H.264/AVC, MPEG-2, VC-1
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3),
Dolby Digital, Dolby Digital Plus, AAC
Video
MPEG-1, MPEG-2
Audio
Dolby Digital, MPEG-1 Layer I, II, DVD-LPCM
Video
MPEG-1
Audio
MPEG-1 Layer I, II
47
48
MY MEDIA
Audio File
File type
MP3
AC3
MPEG
AAC,
HEAAC
CDDA
LPCM
Item
Info
Bit rate
32 kbps to 320 kbps
Sampling rate
32 kHz to 48 kHz
Bit rate
32 kbps to 640 kbps
Sampling rate
32 kHz, 44.1 kHz, 48 kHz
Bit rate
32 kbps to 448 kbps
Sampling rate
32 kHz to 48 kHz
Bit rate
24 kbps to 3844 kbps
Sampling rate
8 kHz to 96 kHz
Bit rate
1.44 kbps
Sampling rate
44.1 kHz
Bit rate
1.41 Mbps to 9.6 Mbps
Sampling rate
Multi-channel : 44.1 kHz, 88.2 kHz /
48 kHz, 96 kHz
Stereo : 176.4 kHz, 192 kHz
MY MEDIA
49
Available photo file
File type
2D (jpeg,
jpg, jpe),
3D (jps)
3D (mpo)
BMP
PNG
Item
Info
Support
File type
SOF0: Baseline, SOF1: Extend Sequential,
SOF2: Progressive
Picture
Size
Minimum: 64 x 64
Maximum: Normal Type: 15360 (W) x 8640 (H)
Progressive Type: 1920 (W) x 1440 (H)
Support
File type
MPO
Picture
Size
4:3 size : 3648 x 2736,
2592 x 1944,
2048 x 1536
3:2 size : 3648 x 2432
Picture
Size
Minimum: 64 x 64
Maximum: 9600 (W) x 6400 (H)
Support
File type
Interlace, Non-Interlace
Picture
Size
Minimum: 64 x 64
Maximum: Interlace: 1200 (W) x 800 (H)
Non-Interlace: 9600 (W) x 6400 (H)
* BMP and PNG format files may be slower to display than JPEG.
50
MY MEDIA
Watching the Videos
In the Movie List, you can watch movies stored on the connected USB
device.
Controls playback and sets options while viewing videos.
Tips for Playing Video Files
• Some subtitles created by users may not work properly.
• The video and subtitle files should be placed in the same folder. For
subtitles to display correctly, the video and subtitle files must have the
same name.
• We do not support any stream that contains GMC (Global Motion
Compensation) or Qpel (Quarterpel Motion Estimation).
• Only H.264/AVC profile level 4.1 and lower is supported.
• Video files that exceed 50 GB (gigabyte) are not supported for playback.
The file size limit is dependent on the encoding environment.
• DTS audio codec is not supported.
MY MEDIA
51
Browsing Movie List
Play a video file stored from a connected device.
1 Connect a USB storage device.
2 Press the USB button.
3 Use the , or button to select Movie List and press the OK
button.
4 Use the
,
,
the OK button.
, or
2
1
button to select the file you want and press
4
3
Page 1/1
Movie List
USB STORAGE DEVICE
Drive1
Drive2
Drive3
Drive4
PAGE
Drive5
Page 1/1
Butterfly_...
01:34:33
Go to root folder
6
Go to upper folder
Exit
7
8
No.
Description
Thumbnails
1
Abnormal file
File not supported
2
File List
3
Moves to the upper level folder.
4
Current page/Total no. of folder pages
5
Current page/Total no. of file pages
6
Moves to the top level folder.
Page Change
5
52
MY MEDIA
No.
Description
7
Moves to the upper level folder.
8
Exit Movie List.
5 Control playback by using the following buttons.
Q.MENU

Item
Option
Hide
나가기Exit
Description
Shows the current playing position. Use
move forward or backward.
or
buttons to
Stops playing and returns to Movie List.
Returns to normal playback.
Pauses the media player.
If no button is pressed on the remote control for 10 minutes
after pausing, the playback is restarted.
Displays in slow motion.
Whenever this button is pressed, the playback speed is
changed.: x2, x4, x8, x16, x32
Reduces power consumption by adjusting peak screen
brightness.
Switches to the 3D screen.
Option
Hide
Exit
A pop-up window will appear.
Hides the playback bar. Press the OK button to make it appear.
Returns to the Movie List screen.
MY MEDIA
53
Options for Movie List
1 Press the Q.MENU button.
2 Use the or button to move to a desired option and press the OK
button.
3 Use the
,
,
, or
button to set up each item.
Set Video Play.
Item
Picture
Size
Audio
Language
Subtitle
Language
Repeat
Description
Selects the size of a playback screen.
• Full: Files are played in full screen mode according to
the aspect ratio of video.
• Original: Displays the video in the original size.
Allows you to select the language you want for the file with
multiple audio tracks. This option is not available if the file
has only one audio track.
The subtitle can be turned on or off.
• Language: One of any of the available languages can
be selected.
• Code Page: A character set used for a subtitle can
be selected. By default, the subtitle is displayed in a
language configured in OPTION 1 → Language.
--Sync: If a subtitle is not synchronized with its video,
you can adjust its speed at 0.5 seconds unit.
--Position: Moves the location of a subtitle.
--Size: Changes the subtitle font size.
Turns the repeat function On or Off.
When it is set to off, the next file can be played
sequentially if the file name is similar.
Set Video.
You can change video settings. (Refer to PICTURE Settings on page 77.)
Set Audio.
You can change audio settings. (Refer to AUDIO Settings on page 84.)
Set 3D Video
You can set 3D video or 2D video.
3D setting
You can set 3D settings. (Refer to OPTION 1 Settings on page 89.)
54
MY MEDIA
Registering the DivX code
Checks DivX Reg. Code for replaying DivX protected videos. Register at
http://vod.divx.com.
Use Reg. Code to rent or purchase movies at www.divx.com/vod.
1 In the Settings menu, move to OPTION 1 and press DivX(R) VOD.
Registration
Deregistration

2 Press the
button.
or
Close
button to move to Registration and press the OK
You must register your device to
play DivX(R) protected videos.
Registration code: XXXXXXXXXX
Register at http://vod.divx.com

OK
3 Check the DivX Registration code.

NOTE
• Rented/purchased DivX files cannot be played if the DivX
Registration Code of a different device is used. Use only the DivX
Registration Code granted to this specific device.
• Converted files not conforming to the DivX Codec Standard may not
play or may produce abnormal sound.
MY MEDIA
To deregister the DivX code
Use the DivX deregistration code to deactivate the DivX DRM function.
1 In the Settings menu, move to OPTION 1 and press DivX(R) VOD.
2 Use the or button to go to Deregistration and press the OK
button.
Registration
Deregistration
Close
Your device is already registered.
Are you sure you wish to deregister?
Yes
No
Deregistration code : ********
Deregister at http://vod.divx.com
Continue with registration?
Yes
No
3 Select Yes.

NOTE
• What is DRM [Digital Rights Management]?
DRM technologies and services protect the interests and rights of
copyright holders by preventing illegal use of digital content. Files
can be played after the license is verified through an online method,
etc.
55
56
MY MEDIA
Viewing the Photos
You can view photos stored on a connected device.
Supported Photo Files
PHOTO (*.JPEG)
Baseline: 64-pixel (width) x 64-pixel (height) - 15360-pixel (width) x
8640-pixel (height)
Progressive: 64-pixel (width) x 64-pixel (height) - 1920-pixel (width) x
1440-pixel (height)
• Non-supported files are displayed in the form of an icon.
• An error message is displayed for corrupted files or file formats that
cannot be played.
• Corrupted files may not be displayed properly.
• It may take some time to view high-resolution images in full screen.
MY MEDIA
57
Browsing Photo List
1 Connect a USB storage device.
2 Press the USB button.
3 Use the or buttons to select Photo List and press the OK button.
4 Use the , , , or button to select the file you want and press
the OK button.
4
3
2
1
Page 1/1
Photo List
USB STORAGE DEVICE
Drive1
Drive2
Drive3
Drive4
PAGE
Drive5
Page 1/1
Butterfly_...
06/09/2014
Go to root folder
6
Go to upper folder
Exit
7
No.
8
Description
Thumbnails
Abnormal file
1
File not supported
2
File List
3
Moves to the upper level folder.
4
Current page/Total no. of folder pages
5
Current page/Total no. of file pages
6
Moves to the top level folder.
7
Moves to the upper level folder.
8
Exit
Page Change
5
58
MY MEDIA
5 Control playback by using the following buttons.
01_a.jpg
2008/12/10
1920 x 1080
479 KB
[1/4]
Slideshow
Item
BGM
Q.MENU
Option
Hide
Exit
Description
Selects the previous or next photo.
Slideshow
All photos are displayed during slide show.
• Set Slide Speed in the Option → Set Photo View. menu.
BGM
You can listen to music while viewing photos in full size.
• Set the BGM in the Option → Set Photo View. menu.
Rotates photos.
• Rotates a photo 90°, 180°, 270°, 360° clockwise.
• Photos cannot be rotated if their width is greater than
the height of the max. supported resolution.
Views the photo in full mode or original mode.
Press the blue button to enlarge the image.
Reduces power consumption by adjusting peak screen
brightness.
Switches to the 3D screen.
Option
A pop-up window will appear.
Hide
Hides the menu on the full size screen.
• To see the menu, press the OK button on the remote
control.
Exit
Exit from full screen photo view.
MY MEDIA
59
Options for Photo List
1 Press the Q.MENU button.
2 Use the or button to move to a desired option and press the OK
button.
3 Use the
,
,
, or
button to set up each item.
Set Photo View.
Item
Description
Slide speed
Selects a slideshow speed.
BGM
Selects a music folder for the background music.
• You cannot change the music folder while the
background music is playing.
• For background music, only the folder from the same
device can be selected.
--Repeat: Selects repeat play.
--Random: Selects random play.
Set Video.
You can change video settings. (Refer to PICTURE Settings on page 77.)
Set Audio.
You can change audio settings. (Refer to AUDIO Settings on page 84.)
Set 3D Video
You can set 3D image or 2D image.
3D setting
You can set 3D settings. (Refer to OPTION 1 Settings on page 89.)
60
MY MEDIA
Listening to Music
You can play audio files stored on the connected device.
Supported Music Files
*.MP3
Bit rate range 32 Kbps to 320 Kbps
• Sampling rate MPEG1 Layer3: 32 kHz, 44.1 kHz, 48 kHz
• Sampling rate MPEG2 Layer3: 16 kHz, 22.05 kHz, 24 kHz
MY MEDIA
61
Browsing Music List
1 Connect a USB storage device.
2 Press the USB button.
3 Use the or button to select Music List and press the OK button.
4 Use the , , , or button to select the file you want and press
the OK button.
4
3
2
1
Page 1/1
Music List
USB STORAGE DEVICE
Drive1
Drive2
Drive3
Drive4
PAGE
Drive5
Page 1/1
Butterfly_...
03:25
Go to root folder
6
Go to upper folder
Exit
7
No.
8
Description
Thumbnails
Abnormal file
1
File not supported
2
File List
3
Moves to the upper level folder.
4
Current page/Total no. of folder pages
5
Current page/Total no. of file pages
6
Moves to the top level folder.
7
Moves to the upper level folder.
8
Exit
Page Change
5
62
MY MEDIA
5 Control playback by using the following buttons.
Page 1/1
Music List
USB STORAGE DEVICE
Drive1
PAGE
Page Change
Page 1/1
Butterfly_...
03:25
002. - B02.mp3
Q.MENU
Item
Option
Hide
Exit
Description
Changes the playing position.
Stops playing.
Returns to normal playback.
Pauses the media player.
Plays the previous/next file.
Reduces power consumption by adjusting peak screen
brightness.
Option
Sets up the options of Music List.
Hide
Hides the playback bar.
• Press the OK button to make the playback bar appear.
Exit
Returns to the Music List screen.
MY MEDIA
63
Options for Music List
1 Press the Q.MENU button.
2 Use the or button to move to a desired option and press the OK
button.
3 Use the
,
,
, or
button to set up each item.
Set Audio Play.
Item
Description
Repeat
Selects repeat play.
Random
Selects random play.
Set Audio.
You can change audio settings. (Refer to AUDIO Settings on page 84.)
64
MY MEDIA
Viewing Files
You can see document files stored on a connected device.
Supported File Formats
XLS, XLSX, DOC, DOCX, PPT, PPTX, TXT, PDF, HWP
Microsoft Office: 97/2000/2002/2003/2007 Version
Adobe PDF: 1.0/1.1/1.2/1.3/1.4 Version
Hangul: 97/2000/2002/2005/2007 Version
• File Viewer realigns a document, so it may look different from what is
displayed on a PC.
• For documents that include images, the resolution may look lower during
the realigning process.
• If the document is large or has many pages, it may take longer to load.
• Unsupported fonts may be replaced by other fonts.
• The file viewer may not open for Office documents that contain many
high resolution images. In that case, reduce the image file size, save it
on a USB storage device and run the file viewer again or connect your
PC to the projector and open the file on your PC.
MY MEDIA
65
Browsing File List
1 Connect a USB storage device.
2 Press the USB button.
3 Use the or button to select File List and press the OK button.
4 Use the , , , or button to select the file you want and press
the OK button.
Page 1/1
File List
USB STORAGE DEVICE
DOC
3
2
1
Drive1
Drive2
Drive3
Drive4
PAGE
Drive5
Page 1/1
Butterfly_...
06/09/2014
Go to root folder
Go to upper folder
Exit
5
6
7
No.
Description
1
File List
2
Moves to the upper level folder.
3
Current page/Total no. of folder pages
4
Current page/Total no. of file pages
5
Moves to the top level folder.
6
Moves to the upper level folder.
7
Exit
Page Change
4
66
MY MEDIA
5 Control playback by using the following buttons.
• Click Go Page, then the pop-up window for selecting the number of
page appears. Input the page to move to the page you want.
• Press the VOLUME +, - button to zoom in or zoom out.
Press the OK button and then use the Up/Down/Left/Right buttons to
move to Go Page or Zoom.
Go Page
Item
ꔦ Zoom
Q.MENU
Option
Hide
Exit
Description
Go Page
Moves to the page you want.
Use the Up/Down/Left/Right buttons to select a page
and press the OK button.
Zoom
Enlarges or reduces the document.
Option
Sets up the options of File Viewer.
Hide
Hides the menu.
• Press the OK button to make it appear.
Exit
Returns to the File Viewer screen.
MY MEDIA
67
Options for File List
1 Press the Q.MENU button.
2 Use the , , , or
button to set up each item.
Set FileViewer Option
Item
Single Page
Loading
Image Quality
Docu­ment
Align
Description
On
Loads and displays pages one by one. The
initial loading time is short but a content-heavy
page may be displayed slowly.
Off
Loads all pages of a file to memory before it
starts to display them. The initial loading time is
long but you can navigate pages quickly after
loading is complete.
If a file is too large, it may fail to load all the
pages.
You can set the quality of the image included in the
document. The following three options are available
for the image quality: High, Medium, Low. Higher the
image quality, lower the display time.
Selects initial document align method.
File Viewer settings are default, so close the currently opened document to
apply changes to the new document, if any.
68
3D FUNCTION
3D FUNCTION
3D technology uses different video frames for each eye to add depth to the
video.
While Watching 3D
WARNING
• If you view 3D video or images too closely for a long period of time, you
may experience eyestrain.
• If you watch the projector or game screen for a long time with 3D
glasses on, you may experience dizziness or eye fatigue.
• People with chronic diseases (epilepsy, cardiovascular disease, blood
pressure-related diseases, etc.), pregnant women, and people with
serious motion sickness should avoid watching 3D video.
• People with stereo blindness, or with stereopsis problems, should also
avoid watching 3D video content. It may cause double vision or visual
discomfort.
• People with strabismus, amblyopia, or astigmatism may have difficulty
perceiving video depth and may be fatigued easily due to double vision
or other ailments. It is recommended to rest more frequently than other
viewers.
• Because 3D can be perceived as real, some viewers may be surprised
or overexcited.
• Do not watch 3D images near fragile objects or any objects that can be
knocked over easily.
• Take care not to injure yourself as you may subconsciously try to move
away from the life-like 3D images.
3D FUNCTION
69
• Warning about photosensitivity seizures
--Some users may experience a seizure or other abnormal symptoms
when they are exposed to a flashing light or particular patterns from
a video game. If anyone in your family has a history of epilepsy or
has ever experienced any kind of seizure, please consult your doctor
before viewing 3D images.
If you experience one of the following symptoms while watching a 3D
video, stop watching the 3D video immediately and take a rest.
--Dizziness, switched eyesight, twitching of the eye or facial muscles,
involuntary movements, cramp, loss of consciousness, confusion,
loss of sense of direction, or nausea. If the symptom does not
disappear, please consult your doctor.
• You can reduce the risk of photosensitive seizures by taking the
following preventive measures.
--Take a rest of 5 to 15 mins. for every 1 hour of viewing.
--If vision varies between each eye, correct the variation before
beginning to watch a 3D video.
--Ensure that the 3D video is directly in front of you, at eye level.
--You should stop watching if you experience a headache, fatigue, or
dizziness.
--Do not view 3D images for a long period of time when you are tired
or ill.
CAUTION
• Extra special care is required for children watching a 3D video.
70
3D FUNCTION
When Watching 3D Video
• Prevent children of 5 years or younger from watching a 3D video. It may
impair the development of their eyes.
• Children 10 years old or younger are still developing their eyesight and
may have an excessive tendency to touch or jump at the screen. Adult
guidance and supervision is recommended.
• Since the distance between the eyes is narrower for children than in
adults, children tend to notice a greater difference in the images seen by
each eye. Therefore, even while watching the same 3D video, children
may have a greater depth perception than adults.
• Children under 19 years old or younger may respond with sensitivity to
the light stimuli of 3D content. Excessive viewing when fatigued is not
recommended.
• Elderly viewers may have a reduced depth perception than younger
viewers. Avoid watching video nearer than the recommended distance.
• Watch 3D images within the optimum viewing angle and distance.
• If you are outside the viewing angle or distance, you may not be able to
see 3D images. You cannot view 3D images when you are lying down.
• You may see left and right images overlapped during projector
initialization after it is powered on. It may take some time for
optimization.
• It may take some time for the 3D image to look normal after you turn
your eyes away from the screen and look back at the 3D image.
• It may flicker slightly while watching 3D images under a 3 wavelength
lamp fluorescent light (50 Hz to 60 Hz) or near windows. If so, it is
recommended to block the sun light with a curtain and to dim the lights.
• The 3D glasses must be DLP-LINK (DLP Ready) type.
• You may not be able to watch 3D properly if there is an obstacle
between the projector and 3D glasses.
• Install the 3D projector as far as possible from other devices.
• If a future 3D broadcasting format that is not supported by this projector
becomes the standard, an additional device such as a set-top box may
be required.
3D FUNCTION
71
Please check the following when using 3D glasses.
• Do not use 3D glasses as ordinary glasses, sunglasses, or protective
goggles.
--If you do so, this may cause injury.
• Do not store 3D glasses in very hot or very cold conditions. If you do,
this may cause them to become distorted. Do not use distorted glasses.
• Do not drop 3D glasses or allow them to come into contact with other
objects.
--This may cause product malfunction.
• The lenses of 3D glasses are easily scratched. Use a soft clean cloth
when cleaning them.
• Foreign particles on the cloth may cause scratches.
• Do not scratch the surface of the 3D glasses' lenses with sharp objects
or wipe them with chemicals. If the lenses get scratched, images may
not look normal when viewing 3D.
72
3D FUNCTION
Requirements for Watching 3D Images
* Optimum viewing angle: Top/Bottom/Left/Right 9°
Recommended viewing distance: 3 m
Recommended screen size: 101 cm

* Watching 3D videos should be done in dark room environments only.
NOTE
• The pairing with the DLP-LINK glasses is affected by the intensity of
light reflected from the screen. Therefore, the pairing with DLP-LINK
glasses may not work properly if the light reflected from the screen is
not bright enough, such as when the surrounding area is bright, the
screen is big, or the maximum energy saving mode is enabled.
• Some menus may not work while playing a 3D video.
• You can only watch a 3D video properly when the 3D video format
option has been selected on the projector.
3D FUNCTION
73
Using the DLP-LINK (DLP-Ready) Type Glasses
1 While watching 3D images from the projector, press buttons on the
glasses.
2 When you press the button, the glasses flicker while synchronizing with
the 3D images. (The flickering is a unique operation method of DLPLINK type glasses. It may be different depending on the glasses type.)
3 If the glasses flicker or problems occur while watching 3D, first turn
the lights off to make the room darker. Contact your projector seller for
queries about the glasses.
To view 3D images
3D imaging is a technology that utilizes the slight difference in left/
right eyes to make the images on the projector appear just like real-life
3-dimensional space.
1 Play supported 3D video titles.
2 Press the 3D button to activate 3D.
3 Turn on the 3D glasses and put them on.
4 While viewing 3D images, press the 3D button on the remote control to
end 3D image viewing.
5 Press the L/R button to switch the playing direction of an image. Select
a screen with better 3D display quality.
--If you press the 3D button during viewing, it returns to 2D.
* Depending on the input signal, the available 3D type may differ.
74
3D FUNCTION
Supported 3D Mode
Horizontal Vertical
Signal Resolution Frequency Frequency
(kHz)
(Hz)
720p
1080i
1280 x
720
1080p
89.9 /
90
59.94 /
60
Frame Packing
75
50
Frame Packing
45
60
Side by side
(half), Top and
Bottom
37.5
50
Side by side
(half), Top and
Bottom
33.7
60
Side by side
(half), Top and
Bottom
28.125
50
Side by side
(half), Top and
Bottom
53.95 /
54
23.98 /
24
Frame Packing
1920 x
1080
HDMI
1920 x
1080
Supported 3D
Formats
67.5
60
Side by side
(half), Top
and Bottom,
Single Frame
Sequential
27
24
Side by side
(half), Top and
Bottom
33.7
30
Side by side
(half), Top and
Bottom
50
Side by
side(half), Top
and Bottom,
Single Frame
Sequential
56.25
3D FUNCTION
Horizontal Vertical
Signal Resolution Frequency Frequency
(kHz)
(Hz)
75
Supported 3D
Formats
USB
1080p
1920 x
1080
33.75
30
Side by side,
Top and Bottom,
MPO, JPS
(Photo)
RGB
1080p
1920 x
1080
67.5
60
Side by
side(half), Top
and Bottom
76
CUSTOMIZING SETTINGS
CUSTOMIZING SETTINGS
SETTINGS
1 Press the SETTINGS button.
2 Use the , , , or button to select the desired item and press
the OK button.
3 Use the
,
,
the OK button.
, or
button to set up the desired item and press
4 Press the EXIT button when completed.
Menu
Description
PICTURE
Adjusts the image quality for optimal viewing.
AUDIO
Adjusts the sound quality and volume level.
TIME
Sets time-related settings.
WIRELESS
Wireless-related features.
OPTION 1
Customizes the general settings.
OPTION 2
Customizes the settings related the projector.
INPUT
Selects the desired input source.
MY MEDIA
Accesses photo, music, movie, and document files.
77
CUSTOMIZING SETTINGS
PICTURE Settings
1 Press the SETTINGS button.
2 Use the , , , or
buttons to select PICTURE
and press the OK button.
3 Use the
PICTURE
ꔂ Move
•• ꕊ Energy Saving : Medium
•• Picture Mode
,
,
, or
button to set up the desired
item and press the OK
button.
--To return to the previous
menu, press the
button.
: Standard
•• Contrast 100
•• Brightness 50
•• Sharpness 10
•• Color
55
•• Tint
0
R
4 Press the EXIT button when
completed.
The available picture settings are described as follows.
Menu
Energy
Saving
ꔉ OK
Description
Reduces power consumption by adjusting peak
screen brightness.
Mode
Minimum/
Applies the pre-set Energy Saving
Medium/
mode.
Maximum
G
78
CUSTOMIZING SETTINGS
Menu
Description
Picture Mode
Selects the picture mode optimized for the viewing
environment or the program.
You can also customize advanced options for each
mode.
Mode
Maximizes the visual effect of video.
Vivid
Heightens contrast, brightness, and
sharpness to display vivid images.
Displays images in standard levels of
Standard
contrast, brightness, and sharpness.
Cinema
Optimizes the image for a movie.
Optimizes the image for sports by
Sport
emphasizing primary colors and
dynamic actions.
Optimizes the image for playing games
Game
on fast-moving screens.
Menu for adjusting picture quality that
allows experts and amateurs to enjoy
the best projector viewing.
Expert1 /
--Expert mode is for picture tuning
Expert2
professionals to control and fine-tune
using a specific image. For normal
images, the effects may not be
dramatic.
Contrast
Adjusts the difference between bright and dark
regions of the screen.
Brightness
Adjusts the overall screen brightness.
Sharpness
Adjusts the sharpness of the borders between bright
and dark. Horizontal and Vertical Sharpness are
available only in Expert1 / Expert2.
Color
Adjusts the intensity of all colors.
Tint
Adjusts the balance between red and green levels.
Advanced
Control
Customizes the advanced settings.
Picture Option
Sets optional settings.
CUSTOMIZING SETTINGS
Menu
79
Description
Picture Reset
Resets values customized by the user.
Each picture mode is reset. Select the picture mode
you wish to reset.
Aspect Ratio
Resizes the picture.
Adjusts the picture quality of RGB-PC input.
Option
Screen (RGBPC)
Resolution
Available resolutions are 768
resolution (1024 x 768/ 1280 x 768/
1360 x 768, 60 Hz) and 1050
resolution (1400 x 1050/ 1680 x 1050,
60 Hz).
Auto
Config.
Provides optimized picture quality by
automatically calibrating the mismatch
of horizontal width and picture shake
caused by clashes between the
internal settings of the projector and
various PC graphic signals.
• You can also use the AUTO button
on the remote control.
Position
Moves the image up/down/left/right.
Size
Changes the screen size.
Phase
Makes the picture look clear by
removing horizontal noise.
Reset
Restores all the settings to the factory
default.
80
CUSTOMIZING SETTINGS
Advanced Control
Menu
Description
Dynamic
Contrast
Adjusts contrast and color to the optimal level according
to the screen’s brightness.
Dynamic
Color
Adjusts colors for more natural-looking colors.
Color
Gamut
Selects the range of colors that can be expressed.
• Standard: Displays the original colors of an input
signal regardless of the display features.
• Wide: Makes use of the display's rich colors.
Skin Color
Skin color spectrum can be separately set to implement
the skin color as defined by the user.
Sky Color
Sky color is set separately.
Grass Color
Natural color spectrum (meadows, hills, etc.) can be
separately set.
Gamma
Sets the gradation curve according to the output of the
picture signal in relation to the input signal.
* Depending on input signal or other picture settings, the range of detailed
items for adjustment may differ.
CUSTOMIZING SETTINGS
81
Expert Control
Menu
Description
Dynamic
Contrast
Adjusts contrast and color to the optimal level
according to the screen’s brightness.
Color Gamut
Selects the range of colors that can be expressed.
• Standard: Displays the original colors of an input
signal regardless of the display features.
• Wide: Makes use of the display's rich colors.
Edge
Enhancer
Shows clearer and distinctive yet natural edges of the
video.
Color Filter
Filters a specific color spectrum in RGB colors to finetune color saturation and hue accurately.
In Expert mode, you can customize the options of each
mode.
Color
Temperature
Gamma: Select 1.9, 2.2,or 2.4.
a. Method: 2 Points
--Pattern: Inner, Outer
--Points: Low, High
--Red/Green/Blue: The adjustment range for each
color is from -50 to +50.
--Apply to all inputs: The values of the Color
Temperature is applied to all the input modes.
b. Method: 20 Point IRE
--Pattern: Inner, Outer
--IRE (Institute of Radio Engineers) is the unit
indicating the size of a video signal and can be
set to 5,10,15, ... 100. You can fine-tune for each
setting as shown below.
--Luminance: The adjustment range is 50 to 500.
--Red/Green/Blue: The adjustment range is -50 to
+50.
--Apply to all inputs: The values of the Color
Temperature is applied to all the input modes.
82
CUSTOMIZING SETTINGS
Menu
Description
Color
Management
System
Adjusts Red/Green/Blue/Cyan/Magenta/Yellow colors.
Allows an expert to adjust the tint using a test pattern.
Six colors (Red/Green/Blue/Cyan/Magenta/Yellow) can
be selectively adjusted without affecting other colors.
You may not see colors change on a normal picture
even after adjustment.
--Saturation Red/Green/Blue/Cyan/Magenta/
Yellow, Tint Red/Green/Blue/Cyan/Magenta/Yellow,
Luminance Red/Green/Blue/Cyan/Magenta/
Yellow:
The adjustment range is -30 to +30 each.
* Depending on input signal or other picture settings, the range of detailed
items for adjustment may differ.
CUSTOMIZING SETTINGS
Picture Option
Menu
Description
Noise Reduction
Reduces screen noise in the video.
MPEG Noise
Reduction
Eliminates noise generated while creating digital
picture signals.
Black Level
Adjusts the brightness or darkness of the screen
to suit the black level of the picture input using the
degree of darkness (black level) of the screen.
Real Cinema
Optimizes the screen for movie viewing.
Color
Temperature
Adjusts the overall color of the screen to suit your
preference.
Select Warm, Natural, Cool, or Medium.
83
84
CUSTOMIZING SETTINGS
AUDIO Settings
1 Press the SETTINGS button.
2 Use the , , , or
button to select AUDIO and
press the OK button.
AUDIO
•• Sound Mode
ꔂ Move
ꔉ OK
: Standard
•• Sound Effect
3 Use the
,
,
, or
button to set up the desired
item and press the OK
button.
--To return to the previous
menu, press the
button.
•• Auto Volume
: Off
4 Press the EXIT button when
completed.
The available audio settings are described as follows.
Menu
Sound
Mode
Description
Sets the sound mode.
Standard
News/Music/
Cinema/
Sport/Game
Mode
Suitable for all types of video.
Sets audio optimized for a specific genre.
CUSTOMIZING SETTINGS
Menu
Sound
Effect
Description
The user can select various sound effects.
Mode
Clear Voice II
Auto
Volume
85
Makes the voice from the projector crisp
and clear.
Virtual
LG’s proprietary audio processing
Surround
technology allows 5 channel-like surround
sound from two speakers.
• When Clear Voice II is set to on,
Virtual Surround cannot be selected.
Equalizer
Adjusts the volume to a level of your
choice using the Equalizer.
• Audio-band (100 Hz/ 300 Hz/ 1 kHz/
3 kHz/ 10 kHz) can be adjusted from
-10 to 10.
• Reset: Resets voice options that the
user has changed.
Balance
Adjusts the balance of the left and right
speakers.
Reset
Initialize the applied effect under the
Sound Effect menu.
Automatically adjusts the volume level.
86
CUSTOMIZING SETTINGS
TIME Settings
1 Press the SETTINGS button.
2 Use the , , , or
button to select TIME and
press the OK button.
3 Use the
,
,
, or
button to set up the desired
item and press the OK
button.
--To return to the previous
menu, press the
button.
TIME
ꔂ Move
•• Sleep Timer
: Off
•• Auto Off
: 60 min.
ꔉ OK
•• Automatic Standby : 4 hours
4 Press the EXIT button when
completed.
The available time settings are described as follows.
Menu
Description
Sleep
Timer
Turns off the projector after a preset number of minutes.
To cancel the Sleep Timer, select Off.
Auto Off
If there is no input signal or button press, the projector
automatically turns off after the preset time has elapsed.
Automatic
Standby
Turns off the projector automatically after a set period of
time if there is no button input on the projector.
87
CUSTOMIZING SETTINGS
WIRELESS Settings
1 Press the SETTINGS button.
2 Use the , , , or
button to select WIRELESS
and press the OK button.
WIRELESS
•• SCREEN SHARE
ꔉ OK
: [PJTR][LG]PW1510[0000]
•• Group
3 Use the
,
,
, or
button to set up the desired
item and press the OK button.
--To return to the previous
menu, press the
button.
ꔂ Move
•• Channel
•• Bluetooth
: Off
•• Search Device
•• List of registered devices
•• AV Sync. Adjust
4 Press the EXIT button when
completed.
The available wireless settings are described as follows.
Menu
Description
The SCREEN SHARE displays the screen of the
connected device.
• You can check the SCREEN SHARE's ID.
Mode
Group
This is the group setting for each device
supporting the SCREEN SHARE feature. When
the wireless connection is weak or unstable,
adjust the group setting to correct the problem.
Channel
You can change the channel used for wireless
connections.
• Search Channels: Select channel
searching methods.
--Auto: The projector searches for
available channels and automatically
selects the least used channel.
--Manual: You can select a channel
manually.
• Channel: This is shown when Search
Channels is set to Manual. It allows you to
specify a channel number to use.
SCREEN
SHARE
88
CUSTOMIZING SETTINGS
Menu
Description
Sound is output through the Bluetooth headset.
First, set Bluetooth to On.
Item
Search
Search for the device to connect to.
Device
Bluetooth List of
Connected devices are saved in the List
registered of registered devices. The saved list of
devices
registered devices can be displayed.
When the video and the sound are not
AV Sync.
synchronized correctly, you can manually
Adjust
adjust the synchronization.
CUSTOMIZING SETTINGS
OPTION 1 Settings
1 Press the SETTINGS button.
2 Use the , , , or
OPTION 1
ꔂ Move
button to select OPTION 1
and press the OK button.
•• Language
,
,
, or
button to set up the desired
item and press the OK
button.
--To return to the previous
menu, press the
button.
•• Auto Input Search : Off
3 Use the
89
ꔉ OK
•• 3D Mode
•• DivX(R) VOD
•• Initial Setting
•• Set ID
:1
•• Mode Setting
: Standard
4 Press the EXIT button when
completed.
The available option 1 settings are described as follows.
Menu
Language
Description
Selects a desired Menu Language.
Adjusts various aspects of 3D imaging.
3D Mode
Mode
3D Picture
Correction
Switches left/right images of 3D video.
Auto Input
Search
Automatically searches for and displays the input
signal type when it is received. It is available only with
external inputs (RGB-PC, HDMI, AV, and Component).
DivX(R) VOD
Sets DivX related settings.
Initial Setting
Resets all the projector settings to the factory default.
Do not turn off the power during initialization.
Set ID
The range of the Set ID is 1 to 99.
Only the saved Set ID takes effect.
Mode Setting
Selects Standard or Store Demo.
When in use in home, please select Standard.
Store Demo mode is for store display.
90
CUSTOMIZING SETTINGS
OPTION 2 Settings
1 Press the SETTINGS button.
2 Use the , , , or
button to select OPTION 2
and press the OK button.
3 Use the
,
,
, or
button to set up the desired
item and press the OK
button.
--To return to the previous
menu, press the
button.
OPTION 2
ꔂ Move
•• Keystone
•• Auto Keystone
: On
•• PJT Mode
: Front
•• High Altitude
: Off
•• Blank Image
: Blue
•• Auto Power
: Off
0
ꔉ OK
-
+
•• Self Diagnosis
4 Press the EXIT button when
completed.
The settings for option 2 are described as follows.
Menu
Keystone
Auto
Keystone
PJT Mode
Description
To prevent the screen image from becoming trapezoidal,
Keystone adjusts the top and bottom width of the image if
the projector is not set at a right angle to the screen.
Auto Keystone provides a rectangular screen image by
automatically adjusting the Keystone number when there
is a trapezoidal screen image caused by tilting of the
projector.
Item
On
Automatically adjusts the Keystone number.
Off
Manually adjusts the Keystone number.
This function turns the projected image upside down or
flips horizontal.
• Select Rear when projecting from the back of the
transparent screen purchased separately.
• Select Front Ceiling when installing the product on the
ceiling.
• When the PJT Mode is Rear Ceiling/Front Ceiling,
the left/right of the speaker changes automatically.
CUSTOMIZING SETTINGS
Menu
Description
High
Altitude
If the projector is used at an altitude higher than 1200
meters, turn this on.
Otherwise, the projector may overheat or its protection
function may be activated. If this happens, turn the
projector off and then on again after waiting for several
minutes.
Blank
Image
Selects a background for blank image.
Makes the projector turn on automatically when the
adaptor plug is inserted.
Auto
Power
Self
Diagnosis
Item
On
When the AC/DC plug is connected to the
projector, it turns on automatically.
Off
When the AC/DC plug is connected to the
projector, it goes into standby mode.
Troubleshoots functional problems that can arise while
using the product.
91
92
CONNECTING DEVICES
CONNECTING DEVICES
You can connect various external devices to the projector.
Computer/Notebook

DVD
Video
Digital Device
USB
Game Console
Headphones
Mobile Phone
HDMI - Page 93
Component - Page 94
Composite (AV) - Page 94
RGB - Page 96
USB Device - Page 44
Headphone - Page 98
Mobile Phone (MHL/Slimport) - Page 99
CONNECTING DEVICES
Connecting to HD
Receiver, DVD, VCR
Player, or External
Devices
Connect an HD receiver, DVD,
VCR player, or External Devices
to the projector and select an
appropriate input mode.
93
HDMI to DVI Connection
Using an HDMI to DVI cable,
connect the projector's
port to the DVI OUT
port.
To output audio, use an audio
cable for connection.
Press the INPUT button on the
remote control to select HDMI.
HDMI Connection
With an HDMI cable, you can
enjoy high quality picture and
sound.
Using a HDMI cable, connect the
RS-232C IN
RS-232C IN
port of the projector
to the HDMI output port of the
device to connect. Both video and
audio are output at the same time.
Press the INPUT button on the
remote control to select HDMI.
RS-232C IN
* Not
provided
* Optional
Extras
RS-232C IN
DVI OUT
RS-232C IN
* Optional
Extras
+'0,
AUDIO OUT
94
CONNECTING DEVICES
Composite (AV)
Connection
Component Connection
Connect the output ports of an
external device and the AV IN
ports of the projector using an AV
cable. Press the INPUT button on
the remote control to select AV.
Check whether cables of the same
color are connected properly.
You can enjoy a video by
connecting the Component port
of an external device to the RGB
IN port of the projector. Press
the INPUT button on the remote
control to select Component.
Check whether cables of the same
color are connected properly.
RS-232C IN
RS-232C IN
RS-232C IN
* Optional
Extras
(Video)
IN
*RS-232C
Accessories
Red
White
3%
9,'(2287
35
/HIW
5LJKW
/HIW
5LJKW
9,'(2287
$8',2287
$8',2287
Red
White
<
Red
5LJKW
$8',2287
Blue
Green
Red
White
Yellow
/HIW
Red
White
Red
Yellow
Red
Blue
Red
Blue
Red
White
Green
White
Yellow
Green
Yellow
* Not
provided
(Audio)
* Optional
Extras
(Video)
* Not
provided
9,'(2287
* Accessories
(Audio)
CONNECTING DEVICES
Connecting a PC
The projector supports Plug and
Play. Your PC will automatically
detect the projector and requires
no driver installation.
HDMI Connection
Using an HDMI cable, connect the
port of the projector
to the HDMI output port of your
PC. Both video and audio are
output at the same time.
Press the INPUT button on the
remote control to select HDMI.
RS-232C IN
95
HDMI to DVI Connection
Using an HDMI to DVI cable,
connect the projector's
port to the DVI OUT
port.
To output audio, use an audio
cable for connection.
Press the INPUT button on the
remote control to select HDMI.
RS-232C IN
RS-232C IN
* Not
provided
RS-232C IN
* Optional
Extras
RS-232C IN
* Optional
Extras
DVI OUT
+'0,
AUDIO OUT
96
CONNECTING DEVICES
RGB Connection
Connect the PC output and the
PC video input port of the projector
with the RGB cable.
For audio signal, connect
the PC
RS-232C IN
and the projector
an optional
RS-232C with
IN
audio cable.
Press the INPUT button on the
remote control to select RGB-PC.
RS-232C IN
* Optional
Extras
* Optional
Extras
RS-232C IN
* Accessories
Red
White
Yellow
* Optional
Extras
5*%2873&
Red
White
* Not
provided
5*%2873&
$8',2287
$8',2287
You can connect the audio cable
without using a gender as shown
in the illustration above.
CONNECTING DEVICES
Connecting a Laptop
You can connect the projector to a
laptop to use various functions.
HDMI Connection
Using an HDMI cable, connect the
port of the projector
to the HDMI output port of your
laptop. Both video and audio are
output at the same time.
Press the INPUT button on the
remote control to select HDMI.
RS-232C IN
RS-232C IN
* Optional
Extras
+'0,
97
The table below shows examples
of switching the output. For
more information, refer to the
External Output, Connecting to
an External Monitor, or similar
sections of the owner's manual of
your computer.
Brand
Switching
Output
NEC
Fn + F3
Panasonic
Fn + F3
Toshiba
Fn + F5
IBM
Fn + F7
Sony
Fn + F7
Fujitsu
Fn + F10
LG
Fn + F7
Samsung
Fn + F4
Macintosh
Adjust the control
panel to enable
mirroring after
start-up.
98
CONNECTING DEVICES
Connecting to
Headphones
You can listen to the audio through
a headphone.
RS-232C IN
* Not
provided
CONNECTING DEVICES
99
Using the Mirroring Function of a Mobile
Phone
MHL/Slimport Connection
RS-232C IN
You must use a HDMI adapter to connect your cell phone to the projector
and to output images and sound from your cell phone to the projector.
The compatible HDMI adapters are different, depending upon your cell
phone type.
Therefore, purchase an appropriate MHL or Slimport adapter.
(To find out whether your device is MHL/Slimport-certified, please contact
your device manufacturer.)
* Optional Extras
NOTE
• When you connect a mobile phone to the
port, you can
see the mobile phone screen through a projector.
–– This only applies to mobile phones that support MHL/Slimport.
–– You can use the remote control for some applications.
• Disconnect the MHL/Slimport cable from the projector when:
–– The MHL/Slimport function is disabled.
–– Your mobile device is fully charged in standby mode.
100 MAINTENANCE
MAINTENANCE
Clean your projector to keep it in optimal condition.
Cleaning
Cleaning the Lens
If there is any dust or staining on the lens surface, you must clean the lens.
Use an air spray or a cleaning cloth to clean the lens.
To remove dust or stains, use an air spray or apply a small amount of
cleaning agent onto a swab or soft cloth to lightly rub the lens.
Please be aware that liquid may flow into the lens if the product is sprayed
directly onto the lens.
Cleaning the Projector Case
To clean the projector case, first unplug the power cord.
To remove dust or stains, use only a dry, lint-free, nonabrasive cloth to
polish the lens.
Do not use alcohol, benzene, thinners, or other chemicals, which may
damage the case.
SPECIFICATIONS
SPECIFICATIONS
MODEL
Resolution (Pixel)
Aspect ratio
Panel size
Projection
distance (Video
size)
Ratio of upward
projection
Working range
of the remote
control
Power
consumption
AC-DC Adaptor
Audio Output
Video input
Height
Width
Depth
Weight
USB Device
Operation
environment
PW1510G (PW1510G-GL)
1280 (Horizontal) × 800 (Vertical)
16:10 (Horizontal:Vertical)
11.623 mm
0.75 m to 3.06 m (63.5 cm to 254.0 cm)
100 %
6m
100 W
Manufacturer: CHICONY
Model: A16-140P1A
19.0 V
7.37 A
(Adaptor Input 100-240 V @ 50/60 Hz)
3W+3W
NTSC M / PAL-B, D, G, H, I / PAL M / PAL N /
PAL 60 / SECAM
53 mm (without foot), 56.5 mm (with foot)
230.6 mm
162 mm
1160 g
5 V, 0.5 A (Max.)
Temperature
Operation 0 °C to 40 °C
Storage
-20 °C to 60 °C
Relative Humidity
Operation 0 % to 80 %
Storage
0 % to 85 %
* Use only power supplies listed in the user instructions.
* Contents in this manual may be changed without prior notice due to
upgrade of product functions.
101
102 SPECIFICATIONS
Supported RGB-PC/HDMI(PC) Mode
Resolution
Horizontal Frequency
(kHz)
Vertical Frequency (Hz)
640 x 350
31.468
70.09
720 x 400
31.469
70.08
640 x 480
31.469
59.94
800 x 600
37.879
60.31
1024 x 768
48.363
60
1152 x 864
54.348
60.053
1280 x 800
49.68
60
1280 x 1024
63.981
60.020
1440 x 900
55.935
59.888
1400 x 1050
65.317
59.979
1600 x 900
60.000
60
1680 x 1050
65.290
59.954
1920 x 1080
67.5
60
• If an invalid signal is input into the projector, it will not be displayed
properly on the screen or a message such as No Signal or Invalid
Format will be displayed.
• The projector supports the DDC1/2B type as the Plug and Play function
(Auto-recognition of PC monitor).
• PC synchronization signal types supported: Separate type
synchronization.
• In PC mode, 1280 x 800 is recommended for the best picture quality.
SPECIFICATIONS
103
Supported HDMI/DVI-DTV Mode
Resolution
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
480p
31.47
31.47
31.5
60
59.94
60
576p
31.25
50
720p
45
44.96
37.5
60
59.94
50
1080i
33.75
33.72
28.125
60
59.94
50
1080p
67.5
67.432
27
26.97
33.75
33.71
56.25
60
59.939
24
23.976
30
29.97
50
• To provide the best picture quality, a 1280 x 720 (720p) resolution is
recommended.
Component port connecting information
Signal
Component
480i / 576i
o
480p / 576p
o
720p / 1080i
o
1080p
o
(50 Hz / 60 Hz only)
104 SPECIFICATIONS
Open Source Software Notice Information
To obtain the source code under GPL, LGPL, MPL, and other open source
licenses, that is contained in this product,
please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a
charge covering the cost of performing such distribution (such as the cost
of media, shipping, and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date
on which you purchased the product.
KEY CODES
105
KEY CODES
This feature is not available for all models.
Code
(Hexa)
Function
Note
AD
POWER
R/C Button
09
MUTE
R/C Button
EF
INPUT
VOLUME +
VOLUME PAGE ,
PAGE,
AUTO
BLANK
R/C Button
02
03
00
01
92
84
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
06
(Arrow Key / Right Key)
R/C Button
07
(Arrow Key / Left Key)
R/C Button
40
(Arrow Key / Cursor Up)
R/C Button
41
(Arrow Key / Cursor Down)
R/C Button
44
5B
28
43
45
BC
79
7C
A4
A5
OK
EXIT
R/C Button
Return (BACK)
SETTINGS
Q.MENU
STILL
RATIO
USB
KEY.S (Keystone)
KEY.S (Keystone)
R/C Button
8E
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
8F
B0
B1
BA
R/C Button
R/C Button
►
R/C Button
R/C Button
R/C Button
106 KEY CODES
Code
(Hexa)
72
71
63
61
Function
Red
Green
Yellow / 3D
Blue / L/R (3D Mode)
Note
R/C Button
R/C Button
R/C Button
R/C Button
EXTERNAL CONTROL DEVICE SETUP
107
EXTERNAL CONTROL DEVICE
SETUP
Connect the RS-232C (serial connector) of the PC to the RS-232C
connector at the back of the Projector.
You need to purchase a cable to connect the RS-232C connectors as it is
not provided as an accessory.
A RS-232C cable is necessary for the remote control of the Projector (see
Figure 1).
RS-232C IN
(PC)
(PC)
(Projector)
(Projector)
Figure 1: RS-232 Connection Diagram
RXD
TXD
DTR
GND
DSR
RTS
CTS
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
2
3
4
5
6
7
8
PC
Projector
* There is no connection to Pin 1 and Pin 9.
9
5
6
1
108 EXTERNAL CONTROL DEVICE SETUP
Set ID
For Set ID number, see "Real data mapping (Hexadecimal → Decimal)".
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to OPTION 1 and press OK.
3 Press the Navigation buttons to scroll to Set ID and press OK.
4 Scroll left or right to select a set ID number and select Close. The
adjustment range is 1-99.
5 When you are finished, press EXIT.
Communication Parameters
•
•
•
•
•
•
Baud rate : 9600 bps (UART)
Data length : 8 bits
Parity : None
Stop bit : 1 bit
Communication code : ASCII code
Use a crossed (reverse) cable.
EXTERNAL CONTROL DEVICE SETUP
109
Command reference list
01. Power*
02. Aspect Ratio
03. Screen Mute
04. Volume Mute
05. Volume Control
06. Contrast
07. Brightness
08. Color
09. Tint
10. Sharpness
11. OSD Select
12. Remote Control
Lock Mode
13. Balance
14. Color Temperature
15. Equalizer
16. Key
17. Energy Saving
18. Input select (Main)
19. 3D
20. Extended 3D
21. Auto Configure
Command1
Command2
k
k
k
k
k
k
k
k
k
k
k
a
c
d
e
f
g
h
i
j
k
l
Data
(Hexadecimal)
00 to 01
(See page 112.)
(See page 113.)
00 to 01
00 to 64
00 to 64
00 to 64
00 to 64
00 to 64
00 to 32
00 to 01
k
m
00 to 01
k
k
j
m
n
x
x
x
j
t
u
v
c
p
b
t
v
u
00 to 64
00 to 04
(See page 117.)
KEY CODES
00 to 02
(See page 118.)
(See page 119.)
(See page 120.)
(See page 120.)
* Note: D
uring playing media, all commands except Power (ka) and Key
(mc) are not executed and treated as NG.
110 EXTERNAL CONTROL DEVICE SETUP
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the Projector. (j, k, m or x)
[Command 2] : Second command to control the Projector.
[Set ID] : Y
ou can adjust the [Set ID] to choose desired projector ID
number in option menu. Adjustment range in Projector is 1 to 99.
If [Set ID] value is selected to ‘0’, every connected set can be
controlled.
* [Set ID] is indicated as decimal (1 to 99) on menu and as
Hexadecimal (0x00 to 0x63) on transmission/receiving protocol.
[DATA] : T
o transmit command data (hexadecimal).
Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return - ASCII code ‘0x0D’
[ ] : Space – ASCII code ‘0x20’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
The set transmits ACK (acknowledgement) based on this format when
receiving normal data. At this time, if the data is data read mode, it
indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
EXTERNAL CONTROL DEVICE SETUP
111
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
The set transmits ACK (acknowledgement) based on this format when
receiving abnormal data from non-viable functions or communication
errors.
Data 00
: Illegal Code
Real data mapping (Hexadecimal → Decimal)
• When you enter the [data] in hexadecimal, refer to following conversion
table.
00 : Step 0
01 : Step 1 (Set ID 1)
...
0A : Step 10 (Set ID 10)
...
0F : Step 15 (Set ID 15)
10 : Step 16 (Set ID 16)
...
32 : Step 50 (Set ID 50)
33 : Step 51 (Set ID 51)
...
63 : Step 99 (Set ID 99)
...
C7 : Step 199
C8 : Step 200
...
FE : Step 254
FF : Step 255
...
01 00 : Step 256
...
27 0E : Step 9998
27 0F : Step 9999
...
112 EXTERNAL CONTROL DEVICE SETUP
* Commands may work differently depending on model and signal.
01. Power (Command: k a)
►► To control Power *On or Off of the set.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : *Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►► To Show Projector is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK][Data][x]
* Similarly, if other functions transmit ‘FF’ data based on this format,
Acknowledgement feedback presents status about each function.
02. Aspect Ratio (Command: k c)
(Main Picture Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the Aspect Ratio in the
Q.MENU or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data
01 : Normal screen (4:3)
04 : Zoom
08 : Full
10 to 1F : Cinema Zoom 1 to 16
02 : Wide screen (16:9)
06 : Set by Program
09 : * Just Scan
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you can select 16:9, 4:3 or Full screen aspect ration.
* In HDMI/Component mode (high-definition), Just Scan is available.
EXTERNAL CONTROL DEVICE SETUP
113
03. Screen Mute (Command: k d)
►► To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data
00 : S
creen mute off (Picture on)
Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, Projector will display On Screen
Display(OSD). But, in case of Screen mute on, Projector will not display
OSD.
04. Volume Mute (Command: k e)
►► To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data
00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the VOLUME +, - buttons on remote
control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
114 EXTERNAL CONTROL DEVICE SETUP
06. Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 0
0 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0
0 to Max : 64
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
08. Color (Command: k i)
►► To adjust the screen color.
You can also adjust color in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 0
0 to Max : 64
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
115
09. Tint (Command: k j)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 0
0 to Green : 64
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min : 0
0 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : O
SD off
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
116 EXTERNAL CONTROL DEVICE SETUP
12. Remote Control Lock Mode (Command: k m)
►► To lock the joystick buttons on the projector and remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this mode.
When main power is off & on (plug-off and plug-in, after 20 - 30 seconds),
external control lock is released.
* In the standby mode (DC off by off timer or ‘ka’, ‘mc’ command), and if
key lock is on, Projector will not turn on by power on key of IR & Local
Key.
13. Balance (Command: k t)
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 0
0 to Max : 64
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
14. Color Temperature (Command: k u)
►► Adjusts the value of color temperature.
Transmission [k][u][ ][Set ID][ ][Data][Cr]
Data
00 : Medium
02 : Warm
* Data 03 is not used.
01 : Cool
04 : Natural
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
15. Equalizer (Command : j v)
►► Adjust EQ of the set.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
0
LSB
0
0
0
0
Frequency
0
0
0
Data
7
6
5
Frequency
4
3
2
1
0
Step
0
0
0
0
1
0
0
1
1
0
0
1
0
1
0
1st Band
2nd Band
3rd Band
4th Band
5th Band
0
0
...
1
1
0
0
...
0
0
0
0
...
0
1
0
0
...
1
0
0
1
...
1
0
0(decimal)
1(decimal)
...
19(decimal)
21(decimal)
Ack [v][ ][Set ID][ ][OK/NG][Data][x]
* It depends upon model, and can adjust when sound mode is EQ
adjustable value.
117
118 EXTERNAL CONTROL DEVICE SETUP
16. Key (Command: m c)
►► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data: To see "KEY CODES".
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
17. Energy Saving (Command: n p)
►► Sets the energy saving mode.
Transmission [n][p][ ][Set ID][ ][Data][Cr]
Data
00 : Minimum
02 : Maximum
01 : Medium
Ack [p][ ][Set ID][ ][OK/NG][Data][x]
18. Input select (Command: x b)
(Main Picture Input)
►► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data
20 : AV
60 : RGB
40 : Component
90 : HDMI
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* This function depends on model and signal.
EXTERNAL CONTROL DEVICE SETUP
19. 3D (Command: x t)
►► To change 3D mode for Projector.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01][ ][Data 02]
Data
Structure
[Data 00]
00 : 3D On
01 : 3D Off
02 : 3D to 2D
[Data 01]
00 : Top and Bottom
01 : Side by Side
03 : Frame Sequential
[Data 02]
00 : Right to Left
01 : Left to Right
[Data 02] functions depend on model and signal.
* All 3D pattern options ([Data 01]) may not be available according to
broadcasting/video signal.
[Data 00]
00
01
02
[Data 01]
O
X
X
[Data 02]
O
X
X
X : don’t care
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02][x]
[t][ ][Set ID][ ][NG][Data00][x]
119
120 EXTERNAL CONTROL DEVICE SETUP
20. Extended 3D (Command: x v)
►► To change 3D option for Projector.
Transmission [x][v][ ][Set ID][ ][Data 00][ ][Cr]
Data 00 : Right to Left
01 : Left to Right
Ack [v][ ][Set ID][ ][OK/NG][Data 00][x]
21. Auto Configure (Command: j u)
►► To adjust picture position and minimize image shaking automatically.
It works only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01 : Run Auto Configure
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
SYMBOLS
SYMBOLS
Refers to alternating current (AC).
Refers to direct current (DC).
Refers to class II equipment.
Refers to stand-by.
Refers to “ON” (power).
Refers to dangerous voltage.
121
Download PDF