OWNER’S MANUAL
Video Conference System
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
V5000
V5500
VR5010H
1303 (V1.6)
2
Safety Information
1 Safety Information
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are expressly
approved in the instruction manual. The user could lose the
authority to operate this equipment if an unauthorized change or
modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
•
A suitable conduit entries, knock-outs or glands shall be
provided in the cable entries of this product in the end user.
•
Caution: Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended
by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
•
Holes in metal, through which insulated wires pass, shall
have smooth well rounded surfaces or shall be provided with
brushings.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
Warning: Do not install this equipment in a confined space such as
a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the National
Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not expose
this product to rain or moisture.
Caution: This installation should be made by a qualified service
person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Caution: The apparatus should not be exposed to water (dripping
or splashing) and no objects filled with liquids, such as vases, should
be placed on the apparatus.
To disconnect power from mains, pull out the mains cord plug.
When installing the product, ensure that the plug is easily
accessible.
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential
requirements and other relevant provisions of
Directive 2004/108/EC, 2006/95/EC, and 2011/65/
EU.
Contact office for compliance of this product :
LG Electronics Inc.
EU Representative, Krijgsman 1,
1186 DM Amstelveen, The Netherlands
Safety Information
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is
attached to a product it means the product is
covered by the European Directive 2002/96/EC.
3. The correct disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of
your old appliance, please contact your city office,
waste disposal service or the shop where you
purchased the product.
•
EEE Compliance with Directive. (for Turkey only)
•
The equipment complies with requirements of the Technical
Regulation, in terms of restrictions for the use of certain
dangerous substances in electrical and electronic equipment.
(for Ukraine only)
Safety way to remove the battery or the battery from the
equipment:
Remove the old battery or battery pack, follow the steps in
reverse order than the assembly. To prevent contamination of the
environment and bring on possible threat to human and animal
health, the old battery or the battery put it in the appropriate
container at designated collection points. Do not dispose of
batteries or battery together with other waste. It is recommended
that you use local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to excessive heat
such as sunshine, fire or the lile.
Disposal of waste batteries/accumulators
IMPORTANT SAFETY
INSTRUCTIONS
1
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong
are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
1. When this crossed-out wheeled bin symbol
is attached to batteries/accumulators of Your
product it means they are covered by European
Directive 2006/66/EC.
2. This symbol may be combined with chemical
symbols for mercury(Hg), cadmium(Cd) or
lead(Pb) if the battery Contains more that
0.0005% of mercury, 0.002% of cadmium or
0.004% of lead.
3. All batteries/accumulators should be disposed
separately from the municipal waste stream via
designated collection facilities appointed by the
government or the local authorities.
4. The correct disposal of Your old batteries/
accumulators will help to prevent potential
negative consequences for the environment,
animal and human health.
5. For more detailed information about disposal of
Your old batteries/accumulators, please contact
Your city office, waste disposal service or the
shop where You purchased the product.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Safety Information
2. All electrical and electronic products should
be disposed of separately from the municipal
waste stream via designated collection facilities
appointed by the government or the local
authorities.
3
4
Safety Information
Safety Warnings and Cautions
1
Safety Information
The following are warnings and cautions for the safety of the users and for the prevention of any property damage. Please read the following
carefully. The safety instructions are divided into "Warning" and "Caution" and below is the definition.
--
Warning: When you violate the instructions, it probably results in serious injury or death.
--
Caution: When you violate the instructions, minor injury or damage that may occur.
WARNING
•
Turn off the system before installation. Do not plug in several electric devices to the same outlet.
--
•
Do not place any liquid container on the system, such as water, coffee, or other beverage.
--
•
•
--
This may cause fire.
--
Recommended operating temperature is over 0 °C (32 °F).
Install the system on a plain surface with sufficient air ventilation. Do not place the system on an elevated surface.
This may cause fire, over heating or electric shock.
Do not touch power cords and signal cables while thunder and lightning.
--
•
This may cause system breakdown or serious injury.
The power outlet must be placed on the ground, and the voltage range must be within 10 % of the voltage rate. Do not use the same
outlet with a hair dryer, iron, refrigerator, or any heating appliances.
--
•
This may cause fire, electric shock, or injury.
Install the system in a cool place without direct sunlight and always maintain room temperature. Avoid candlelight and heat generating
devices such as heaters. Keep the system away from places where many people pass.
-•
This may cause fire or electric shock.
Install the system in a place with sufficient air ventilation. Keep at least 15 cm between the back of the system and the wall for the cables
connected to the system, otherwise they may be bent, damaged, or cut.
--
•
This may cause fire, electric shock, or serious injury.
Check for any danger signs such as a wet floor, a loosened or damaged power cable, or an unstable surface. If you encounter any problems,
ask your dealer for assistance.
--
•
This may cause fire or electric shock.
Do not attempt to disassemble, repair, or modify the system on your own without seeking assistance from LG Electronics. It is extremely
dangerous due to the high voltage running through the system.
--
•
This can cause fire or electric shock.
When pulling the power cable from the plug, do so gently. Do not touch the plug with wet hands and avoid using the plug if the holes in
the outlet are too loose.
--
•
This may damage the surface of the system and can cause a system breakdown or electric shock.
Avoid placing the system near moisture, dust, or soot.
--
•
This may cause fire.
Dust around the system on a regular basis. When cleaning the system, always use a dry cloth. Do not use a wet cloth or other organic
solvents.
--
•
If liquid is poured into the system, it can cause a system breakdown or fire.
Prevent the power cable from being severely bent or having pressure exerted on it by a heavy object.
--
•
This may cause over heating, fire, or electric shock.
This can cause electric shock.
Do not disconnect power cord during using.
--
This may cause electric shock to product.
•
Do not turn on or off the product by using power plug. (Do not use power plug as switch. This may cause electric shock or malfunction)
•
If you are not used for a long time, separate from its power cord.
--
•
Dust accumulation may cause due to leakage, electric shock or fire due to heat, fire and insulation degradation due to leakage, electric
shock or fire.
When transporting the product, be sure to turn off and disconnect all cables connected to pins and transport.
--
This may cause a electric shock and system breakdown.
Safety Information
•
Main blocking device of power supply is power cord, this blocking device must be in a location that can be easily manipulated. The
product is connected to AC wall power, the switch is turned off when AC power is not completely blocked. Disconnecting the power
supply should be '0 ' power consumption.
•
The product has been dropped or the case is broken, turn off the power and unplug the power cord.
--
If the product has no video out or sound, please stop using. Unplug the power cable immediately and contact the service center.
--
This may cause fire or electric shock.
CAUTION
Please beware of the following precautions before installing the VCS.
•
Keep the system turned off before installation.
•
Keep the product away from electric sparks or magnetic substances.
•
Avoid temperature extremes. (Recommended operating temperature is between 0 °C and 40 °C)
•
Ensure enough space is left for cable connections.
•
Place the system on a solid surface with sufficient air ventilation. Avoid any surface that vibrates.
•
Placing the system near electronic devices such as a radio may cause the product to breakdown.
•
Prevent any substances from being inserted into the system.
--
•
Do not install the system in a place with high magnetic, electric wave, or wireless devices such as a radio.
--
•
This may cause system breakdown.
Install the system on a stable, level surface.
--
•
Do not install the system in a place with magnetic objects, electric frequencies, or vibration.
Do not place any heavy object on the system.
--
•
This may cause system breakdown.
The system may not operate properly.
Install the system in a place with appropriate moisture and temperature levels.
--
Avoid installing the system in a place with high (over 40 °C) or low (under 0 °C) temperature.
•
The system can be damaged from a strong impact or vibration. Avoid throwing objects within the vicinity of the system.
•
Avoid direct sunlight or any heating appliances.
•
Ventilate the air inside the system operation room, and tighten the system cover firmly.
--
System breakdown may be caused by an inappropriate environment. It is recommended to use AVR (Automatic Voltage Regulator)
for a stable power supply. It is recommended to coil the core-ferrite around the connector of the system to avoid electromagnetic
interference.
•
The outlet must be placed on the ground.
•
If there is strange sound or smell, unplug the power cable immediately and contact the service center.
--
•
This may cause fire or electric shock.
In order to maintain stable system performance, have your system checked regularly by the service center.
--
LG Electronics is not held responsible for system breakdown caused by user mishandling.
--
There is a risk of explosion if a battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
•
Do not overturn the product during use.
•
Do not use or place near flammable materials.
--
This may cause explosion or fire.
•
If you use only a specific screen for a long time, it may remain badly damaged. Use a screen saver mode.
•
The device as business type EMC Equipment (A grade), the seller or the user should be operated outside of the home is intended to be
used in.
1
Safety Information
•
This may cause fire or electric shock. Please contact Service center.
5
6
Contents
Table of Contents
1 Safety Information
3
4
IMPORTANT SAFETY INSTRUCTIONS
Safety Warnings and Cautions
2Preparation
8Introduction
8
What is the VCS?
8Features
9Unpacking
10
11
12
Codec Unit Overview
HD Camera Overview
Remote Control
12
Before Using the Remote Control
13
Remote Control Functions
3Installation
14Connections
14Precautions
14
Connection Overview
15
HDMI Connection
16
HD Camera Connection
17
PC Connection
18
Connecting to a Network
19
Connecting an Audio device
20
Connecting a Microphone
21
Connecting Power
21
System Connection Check
22
24
27
28
29
Using the CODEC UNIT STAND
Initial Settings
Main Screen Overview
System Configuration Menu
User Settings
29General
30Camera
31
32
Date Time
Admin Settings
32
Call Settings
36
Network Settings
42
System Settings
44
System Information
44
System Status
44Video
45Audio
45
Network Utility
46
Server Status
Contents
7
4Operation
47
47
Before Using the System
Placing a Call
47
Placing a Call Manually
48
Multipoint Call (V5500 Only)
48
Placing a Call from the Call History
49
Placing a Call from the Directory
49
Placing a Call using the Speed Dial
49
49
Ending a Call
49
Hiding or Showing User Interface Elements
50
Managing Audio
50
Managing Video Layout
51
Managing Video Contents
53
Viewing Call Information
54
4
Get the Snapshot
Adding an Entry to the Directory
55
Editing or Deleting an Entry from the Directory
55
Copying an Entry from the Call History
55
Copying an Entry from the Corporate Contact
56
Deleting an Entry from the Call History
56
Sorting and Searching
56
Placing a Call when the Device is Registered in Gatekeeper Server
56
Making a Call when the Device is Registered in SIP Server
57
Using the Camera Control
57
Using Preset function
58
Using SnapShot
59
3
Managing the Directory
54
58
2
Answering or Rejecting a Call
Managing a Call
49
53
1
Using Power Off
Using the Web Service
59
Login the web service
60
Using the web monitoring function
61
Using the web recording function
62
Upgrading your System Software
62
Uploading the Certification File
63
Importing or Exporting the Address Book
5Appendix
64Troubleshooting
66
Open Source Software Notice
67Specifications
5
8
Preparation
2Preparation
2
Preparation
Introduction
What is the VCS?
The LG VCS (Video Conference System) is designed to be used for video conferencing that enables people in different places to have a meeting
by seeing, listening and speaking to each other on a screen.
Through this device, not only can executives or managers have a meeting and communicate with customers, subcontractors and coworkers
in real time but decisions can be made and information can be exchanged virtually and immediately, saving travel time, cost and energy.
Network
VCS
Features
•
Convenient and easy graphical user interface
•
H.323 / SIP network Internation Standard codec
•
HD video quality – 1 280 X 720 (30 fps)
•
Selectable screen layouts
•
Graphic presentation using Content Sharing Function
•
Administrator password for security
•
One-touch call connection using speed dial
•
Graphical directory using snapshot and specific group management
•
Easy phonebook search function
•
720p high-definition camera
•
Natural sounding conversation using full duplex mode
•
3.5 mm Micpod with Mute
•
Pan/Tilt/Zoom control of the camera
VCS
Preparation
9
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your
product. The illustrations in this manual may differ from the actual product and item.
2
Preparation
Codec Unit
HD Camera
Remote Control and Batteries
Video Conference System
V5500
Quick Setup Guide
DC 12 V
6
Video Conference System
Quick Setup Guide
1
V5500
2
CAMERA
CABLE
HDMI
CABLE
Optional
D-sub
CABLE
4
3
HDMI
CABLE
LAN
CABLE
DC 12 V
1
2
CAMERA
CABLE
Optional
Optional
6
HDMI
CABLE
Optional
D-sub
CABLE
3
HDMI
CABLE
5
TV
4
LAN
CABLE
Optional
Optional
TV
Optional
5
Optional
Power Adapter
HDMI Cable
Video Conference System
Quick Setup Guide
Camera Connection Cable
V5500
DC 12 V
6
1
CAMERA
CABLE
2
HDMI
CABLE
Optional
D-sub
CABLE
3
HDMI
CABLE
4
LAN
CABLE
Optional
TV
Optional
5
Optional
1
Owner’s Manual CD
Quick Setup Guide
MicPod
Codec Unit Stand
10
Preparation
Codec Unit Overview
a
2
Preparation
b
c d e
f
g
h
i j
k
l
mn o
a
Power indicator: Lights when the unit turns on.
b
If you use the codec unit as stand type, attach the codec unit to the codec unit stand. For more details, refer to 22 page.
c
Power input jack: Connects to a DC 12 V power supply using proper cables.
d
Power button: Turns the unit on or off. You must turn the unit on using the Power button after connecting the power cable. You can
use this button to reset the system.
e
Camera connection port: Connects the HD camera.
f
HDMI Input port: Connects the codec unit and the camera with a HDMI cable.
g
RGB(PC) IN port: Connects the PC with a D-sub cable for presentation.
h
Cooling fan.
i
HDMI OUT 1 port: Connects the codec unit and the display device with a HDMI cable for main output.
j
HDMI OUT 2 port: Connects the codec unit and the display device with a HDMI cable for contents output.
k
LAN port: Connects to a network via a hub with RJ-45 connector.
l
AUDIO IN/OUT: Connects to the external audio device.
m
Microphone jack 1: Connects a microphone.
n
Microphone jack 2: Connects a microphone.
o
LOCK: Connects the Kensington security system cable between the Codec Unit and a large object such as a desk.
Preparation
11
HD Camera Overview
V5000
2
Preparation
a
b
c
de
f
a
b
c
ed f
VR5010H
a
Remote sensor: Point the Remote control here.
b
Camera activation indicator: Lights when the camera is connected to the codec unit and activates correctly.
c
LOCK: Connects the Kensington security system cable between the Camera and a large object such as a desk.
d
Power input jack: Connects to a DC 12 V power supply using proper cables.
e
RJ-45 connection port: Connects the codec unit and the HD camera with the supplied camera connection cable. It enables power
to be provided to the camera and communicate with codec unit. The camera is operated without external power supply when the
camera and codec unit are connected with the supplied Camera connection cable.
f
HDMI port: Connects the codec unit and the camera with a HDMI cable.
12
Preparation
Remote Control
This remote control provides wireless control of all video conference system functions and enables you to navigate the user interface, place
and receive calls and control the far end of the camera connected to the system.
2
Before Using the Remote Control
Preparation
Open the battery cover, replace batteries (1.5 V AAA) matching 2 and 3 ends to the label inside the compartment and then close the
battery cover.
CAUTION
Do not mix old and new batteries as this may damage the Remote Control.
Preparation
13
Remote Control Functions
Button
Description
Button
Description
Displays the system or call
information.
Use this button to zoom in or
zoom out of the near end and
the far end camera.
Use this button to adjust the
volume of the system in a call.
Use this button to mute
microphones of the near end
system.
If you press this button during
a call, the camera image will be
displayed to the opposite sides
of the current camera position
and mute the microphones of
the near end system.
Use this button to select the near
or far end camera. You can use
the below functions.
Use this button to select the
video input source (camera or
PC) of the near camera.
•
Preset setting
•
PTZ control
•
Selects a video source
Displays the system setup menu.
Use this button to enable the
presentation function.
•
Arrow buttons: Navigate
the menu options. Use this
button to Pan/Tilt control for
far end camera.
Use this button to return to the
previous condition.
•
OK: Confirms menu
selections.
Use this button to set the far end
camera preset.
Use this button to change the
screen layout.
Use this button when you want
to make a call.
Displays the directory menu.
Use this button when you want
to hang up the call.
Function buttons.
Each button function changes as
the condition of the menu and
system operation refers to the
each screen for more details.
Use these buttons to input text
or numbers.
Use these buttons to control
the LG TV. If you want to use this
function, the VCS is connected
with HDMI TV via the HDMI
Output 1 port.
•
: Turns the TV power On
or Off.
• CH. +/- : Use this button to
change the channel.
• INPUT: Selects the input
source.
• MUTE: To mute the sound.
• VOL +/-: Use this button to
adjust the volume of the TV.
•
DEL.: Delete a character
before the cursor position.
•
SPACE: Insert a space at the
cursor position.
•
1/a/A: Change the input type
among the number, lower
case and upper case.
2
Preparation
Changes the unit to idle (ON) or
standby (OFF) mode. For more
details by using the power off,
refers 58 page.
14
Installation
3Installation
Connections
3
Precautions
Before setting up the system, ensure that the monitor, the computer system and other attached devices are turned off.
Installation
Connection Overview
The illustration below shows the connections of the system. For specific information of each connection, refer to the next pages.
Connection Overview
7
1
2
3
4
6
5
Installation
15
HDMI Connection
Transmit the digital video and audio signals from the system to your monitor with the HDMI cable as shown in the following illustrations.
HDMI Cable Connection
3
Installation
Optional
NOTE
•
It is recommended to use the monitor with built-in speaker and 1280X720 mode for the best image quality.
•
If you connect the codec unit to the DVI port of monitor (TV) using HDMI to DVI converter, you should hear the audio through Audio out
device because DVI does not support audio interface. Please go to [Setup > Admin > System > Audio > Audio Out] and change [Audio
Out] to “Line Out”.
•
The HDMI OUT 2 port is used to output the contents. If you connect the HDMI OUT 2 port and use it, please go to [Setup > User >
General > Second Display] and set to On.
•
Do not connect Camera Input HDMI Cable to HDMI TV or monitor.
16
Installation
HD Camera Connection
Connects the HD camera to the camera jack of the codec unit with the supplied camera connection cable(RJ-45[with power] to D-sub Cable)
as shown in the following illustrations.
HD Camera Connection
3
Installation
V5000,V5500
Optional
DC 12 V
VR5010H
Optional
DC 12 V
NOTE
•
After connection is completed, adjust the angle of the camera to suit your view.
•
Do not Connect HDMI Out Cable to Camera HDMI Input Port.
•
It is recommended to use the camera with the 1280 x 720p60 mode.
•
Do not connect Camera Connection Cable (RJ-45[with power] to D-Sub Cable) to other device's LAN Jack. (e.g. Note book LAN Jack)
•
After connecing the Camera Connection Cable properly, turn on the Codec Box. Otherwise the VCS may cause malfunction.
•
Do not hold the camera forced for a long time. Install the camera in a place with sufficient not to interrupt the rotation. This may cause
product to breakdown or power may turn OFF automatically.
Installation
17
PC Connection
Transmits an analog video signal from your PC to codec unit. Connect the PC and the codec unit with the optional D-sub 15-pin signal cable
as shown in the following illustrations. You can give a presentation to the far-end user with this connection.
PC Connection
3
Installation
NOTE
•
The D-sub Cable (D-Sub 15 pin female to D-sub 15 pin) is not included. So purchase the cables separately.
•
This unit supports 640 x 480, 800 x 600, 1 024 x 768, 1 280 x 720, 1 280 x 768, 1 280 x 1 024, 1 400 x 1 050 and 1 920 x 1 080 and 60Hz for
PC output resolutions.
•
If the PC screen can not see properly after D-sub cable insert or remove from the VCS, check the PC video output connection again .
18
Installation
Connecting to a Network
Connects the codec unit’s LAN port to a corresponding port on your router or network using an optional LAN cable with RJ-45 connector.
Network Connection
3
Installation
NOTE
When plugging or unplugging the LAN cable, hold the plug portion of the cable. When unplugging, you should hold the lock of the plug
portion.
Installation
19
Connecting an Audio device
Connects an audio device to the AUDIO OUT port of the codec unit as shown in the following illustrations.
Audio Device Connection
3
Installation
NOTE
•
You can transport sound by connecting the AUDIO OUT device to the AUDIO IN Port.
•
If you connect the AUDIO IN port and use it, please go to [Setup > Admin > System > Audio > Audio IN] and set to [Line IN].
20
Installation
Connecting a Microphone
Connects a microphone to the MIC port or ADUIO IN port of the codec unit as shown in the following illustrations.
Microphone Connection
3
Installation
Optional
NOTE
•
Refer to QSG (Quick Setup Guide) for details.
•
The recommended distance between the microphone and the user is about 1 m to 2 m.
•
It is recommended to use two of microphone in the auditorium.
•
Place two of microphone to fill the sounds whole of conference room and leave space more than 4 m distance between each
microphone.
•
You can transport voice by connecting the microphone device like as Gooseneck microphone to the AUDIO IN Port.
•
If you connect the AUDIO In port and use it, please go to [Setup > Admin > System > Audio > Audio In] and set to [Microphone].
Installation
21
Connecting Power
Connects the power cable as shown in the following illustrations.
Power Connection
3
Installation
CAUTION
You must use a supported adapter. If you connect another adapter not offered with the system, you may cause a malfunction, failure or fire.
System Connection Check
After all of the connections are completed, follow the steps below to check the system operation.
1. Turn on the monitor.
2. Press POWER on the rear of the codec unit.
System booting will commence. When the booting is completed, the initial configuration menu will be displayed.
If it is not displayed, check the device connections and make sure the connections are correctly set.
Now, you can use the system. Do the next configuration.
22
Installation
Using the CODEC UNIT STAND
If you use the codec unit as stand type, attach the codec unit to the codec unit stand as shown in the following illustrations.
1. Remove the stand connection cover from the codec unit.
3
2. After aligning the position, attach the stand connection cover to bottom of the codec unit stand.
Loosen the fixing screws in bottom of codec unit stand.
Installation
3. After aligning the position, connect the codec unit to the codec unit stand.
Installation
23
4. Tighten the fixing screws in bottom of codec unit stand.
3
Installation
24
Installation
Initial Settings
When you access the VCS for the first time, the initial setting screen appears. Select a language and customize the basic settings.
1. Insert two AAA batteries matching 2 and 3 correctly into the remote controller.
2. Turn on the unit. System booting will commence. The logo image will be displayed during the system booting.
3. When the booting is complete the initial configuration menu will be displayed.
4. Select the language for the text displayed on the screen.
3
Installation
4-1. Select the Language option and press OK or [
4-2. Select the language using [
4-3. Select [Next] and press OK to go to the next step or press
5. Select the wizard option.
] or [
]. The language list is displayed.
]and press OK.
ll
.
Installation
5-1.
•
25
Select one of the below options.
Start Wizard: Select this option when you want to set the configuration with wizard. If you select this option, follow next steps.
NOTE
It is recommended that you use the Start Wizard option rather than the Manual Setting option.
•
Manual Setting: Skip the wizard configuration and display the main setup window. You can set the system configuration manually.
NOTE
If you setup incorrectly in Manual Setting, you may not be able to connect to calls.
5-2.
Select [Next] and press OK to go to the next step or press
ll
.
3
6. Select the time zone.
Installation
6-1.
Use [
] or [
] to select the time zone and press OK.
6-2. Use [
] or [
] to select the country where the device is located and press OK.
6-3. Select [Next] and press OK to go to the next step or press
ll
.
7. Select the one of the network setting options.
•
DHCP: Select this option when a DHCP server is installed on the network to allow IP address assignment. With this setting, the IP address
is assigned automatically.
7-1. Select this option and press
ll
. The IP address information window is displayed.
26
Installation
7-2. •
Select [Next] and press OK to go to the next step or press
ll
.
Static: Select this option when you set the network configuration manually.
7-1. Select this option and press
7-2. Set the below options.
7-3. ll
.
--
IP Address: Enter the static IP address of the device.
--
Subnet Mask: Enter the subnet mask IP address.
--
Gateway: Enter the gateway IP address.
--
DNS Server: Enter the IP address to configure DNS servers.
Select [Next] and press OK to go to the next step or press
ll
.
8. Enter a descriptive name for the system.
3
Installation
When using the remote control
8-1. 8-2. Press OK to edit the system name.
Enter the system name using the Remote control buttons and press OK to confirm it.
•
DEL.: Deletes the previous character at the cursor position.
•
SPACE: Inserts space at the cursor position.
•
1/a/A: Changes the input type to numbers, small letters or capital letters.
Numbers/[.*#]: Select the numbers, small letters or capital letters as selected input type. Press the button repeatedly to select
the character or symbol as you want.
•
When using the virtual keyboard.
8-1. Select the virtual keyboard icon and press OK. The virtual keyboard input menu displayed.
8-2. Use the arrow buttons to select a letter and OK to confirm your selection.
•
<<: Moves cursor to left.
•
>>: Moves cursor to right.
•
Clear: Deletes the previous character at the cursor position.
•
Clear All: Clear all the entered characters, numbers and symbols.
•
Space: Inserts space at the cursor position.
•
a/A/?!: Changes the virtual keyboard settings to small letters, capital letters or symbols.
•
OK: Confirms and exit the menu.
•
Cancel: Returns to the previous screen.
9. The Wizard finish message is displayed, press OK to start VCS. The VCS main screen will be displayed.
Installation
27
3
Installation
NOTE
•
Additionally, refer to the on-screen instructions for each option’s setting.
•
If you want to move to the previous option settings, select [Prev] and press OK or press
l
.
Main Screen Overview
ab
g
h
c d e
i j
kl
m
f
n op
28
Installation
a
Current Date and Time: Displays the current date and time.
b
Call History: You can make a call by selecting a number from a list of recently dialed numbers.
c
Speed Dial: You can see a list of recently saved speed dial number. You can make a call by pressing a number button of remote
controller and selecting a number from list.
d
Local Video Area: Displays the current input video of the local camera.
e
Directory: Enter the directory tab to see your My Contact.
f
Status Icons
Activated
Disconnected
Description
Displays the network status
3
Installation
Displays the Microphone status
Displays the camera status.
Displays the speaker status.
-
Displays the network server status.
g
Call Speed: You can select the call speed.
h
System Name: Displays the current system name.
i
IP Address: Displays the current IP address of the unit.
j
Text Input Field: Enter the dial numbers or IP address manually.
k
Call Button: Use this button when you want to make a call.
l
Menu Hide: You can hide the user interface elements and you can show the user interface element other remote key.
m
Camera Control: You can select the appropriate view area.
n
Call: You can make a call from text input field address.
o
Setup: You can enter setup menu so you can change system status.
p
System Info: You can display system status, Audio, Video, Network Utility and Server Status.
System Configuration Menu
The features and options of the VCS are configured through the setup menu.
1. On the main screen, press Setup to access the Setup Menu.
Use the below buttons on the remote control to navigate the menu options.
•
Arrow buttons: Use these buttons to select the menu options or adjust the options value.
•
OK: Select the option or confirm the setting.
•
BACK: Return to the idle status.
2.Press Setup to exit the setup menu.
Installation
29
User Settings
General
3
Installation
•
System Name: Enter a system name using up to 127 characters. The inputted system name is displayed on the main screen.
1. Press OK.
2. Edit the system name using the virtual keyboard or remote control.
3.Press OK to confirm the setting.
NOTE
If you connect a SIP call, you have to enter alphanumeric.
If you enter other characters except letters, numbers, “.”, “-” and “_”, you cannot connect a SIP call.
•
•
Call Mode: Select a call mode.
--
Audio+Video: When you make a call with audio and video.
--
Audio Only: Select this option when you want to call with audio only.
Answer Type: Select the answer type for the incoming call.
--
Auto answer : The system automatically answers the incoming call.
--
Manual: You must manually answer incoming calls.
--
Do not disturb me : When the system Do Not Disturb feature is enabled, the system displays the main screen. Callers hear a busy
signal and missed calls appear in the Call History. Consider using this feature, for example, if you are using the meeting room for a
purpose other than a video conference and do not wish to be disturbed by incoming calls.
•
Screen Saver: When your system is idle during the selected time, it will be activated and the LG logo will be displayed on the monitor.
An incoming call or pressing any button on the remote control automatically invokes the system.
•
Language: Select a language for the setup menu and information display.
•
Outgoing Protocol: Select the protocol to use when attempting to outgoing Call. You can choose H.323, SIP, or Auto. If you select H.323
or SIP, you can make a call selected value. If the far site user does not enable the same protocol, you can’t connect to the far site. If you
selected Auto, you are able to connect moderately with the far site setting. (H.323 is tried before the SIP. If H.323 does not connect, a SIP
call is attempted automatically.)
•
Display Resolution: Select the display resolution of the connected monitor. If you change the resolution, the confirmation window is
displayed and then press OK to reboot the system. You can set the system to 720p, 480p. The default is 720p.
•
Second Display: Set to ON when you use the second display for content viewer. If you use the content sharing function, the content will
be displayed from the second display device of the connected with the HDMI OUT 2 port.
30
Installation
Camera
3
Installation
•
•
White balance Mode: Select the Whitebalance activation mode. Adjust the white balance when video color appears to be unbalanced.
White balance is affected by the type of light source.
--
Auto: The whitebalance function is activated automatically.
--
ATW: The color temperature range for the proper white balance is approximately 1 700 K to 11 000 K.
--
Manual: Adjust the white balance level on the Whitebalance level menu.
White Balance Level: Set the white balance level. This option is activated when set manual in the [White Balance Mode] menu.
1. Press OK and adjust white balance using the left or right arrow button.
2. Press OK to confirm the setting.
•
Color: Select the Color level for the camera. You can improve or suppress the color level by manually adjusting the camera color
reproduction.
1. Press OK and adjust color level using the left or right arrow button.
2. Press OK to confirm the setting.
•
Brightness: Select the brightness level for the camera. Camera brightness refers to the received amount of light through the lens of the
camera. You can improve dim scenes by manually adjusting the camera brightness.
1. Press OK and adjust brightness using the left or right arrow button.
2. Press OK to confirm the setting.
•
Sharpness: Select the sharpness level for the camera.
1. Press OK and adjust sharpness using the left or right arrow button.
2. Press OK to confirm the setting.
•
Focus Mode: Select the camera focus mode.
--
Trigger Auto: The focus function is activated when using the PTZ function manually.
--
Auto: The focus function is activated automatically.
•
Shutter: Lights powered by a 50 Hz power source can produce a flicker that the camera captures and transmits to the system. If you are
using lights powered by a 50 Hz power source and observe a flicker in the video displayed in your system, select the Anti-Flicker (60 Hz)
option. The default option is Auto.
•
Backlight:
•
--
On: Select when you want to activate the Backlight function. If you set to On, the WDR option is disenabled.
--
Off: Not used.
WDR: WDR (Wide dynamic Range) feature can be very helpful to cope with very challenging lighting conditions. It is capable of
capturing both of the dark part and bright part and combining the differences into a scene to generate a highly realistic image as
original scene.
--
On: Select when you want to activate the WDR function. If you set to On, the Shutter and Backlight options are disenabled.
--
Off: Not used.
Installation
31
Date Time
3
Installation
•
Time Server: Select time setting method.
--
Auto: Set the time server automatically.
--
Manual: Set the time server manually. Usable NTP servers are shown below.
NTP Server
time.nist.gov
IP address
192.43.244.18
time-a.nist.gov
129.6.15.28
time-b.nist.gov
129.6.15.29
ntp.nasa.gov
198.123.30.132
clock.isc.org
204.152.184.72
time.bora.net
203.248.240.140
•
Time Server Address: Enter the IP address or hostname of the time server. This option is activated when you set to manual in the [Time
Server] setting menu.
•
Date Format: Select the display format for date.
•
Daylight Saving: Set the daylight-savings time.
1. Press OK and then the daylight-savings time setting menu will be displayed.
2. Mark up to set the daylight-savings function.
3. Set the daylight-savings start time.
4. Set the daylight-savings end time.
5. Press OK to confirm the setting. After setting, the daylight-savings option is set to On.
•
Time Zone: Select the time zone for your system.
32
Installation
Admin Settings
If you select this, the password input window is displayed.
To change the administrator settings, you should input the password. The default administrator password is “1234”.
Enter the password to display the administrator sub-menu options.
Call Settings
General
3
Installation
•
Maximum Call Time: Enter the Maximum Call Time from 0 minute to 99999 minutes. After the entered minutes, the pop-up will be
displayed. So, you can hang up or continue the call.
•
Maximum Bandwidth: Select the maximum amount of network bandwidth to use for video call.
H.323
This unit supports the H.323 protocol for placing and receiving video and voice calls. This is used when a gatekeeper function is attempted.
•
H.323 Name: Enter the name of the device used when making calls with H.323 with the alphabet, numbers and special characters.
•
E.164 Name: Enter the name of the device used when making calls with numbers. This name is used when users register in the
gatekeeper server. If the device is registered on gatekeeper server, the far site user can call this name.
Installation
•
Security: H.235 128-bit AES security in H.323 calls. When enabled, the system automatically encrypts calls to other systems that have
AES encryption enabled. When set to AES, calls connect, are encrypted only if the far end supports AES encryption. If the far end user
does not support AES encryption, calls are not encrypted.
•
Use Gatekeeper: Set to On when you use the gatekeeper function. This unit supports the H.460 protocol for firewall and NAT traversal
of H.323 calls. You must have an H.460 server configured in your environment for this feature to function properly. If you set to On, the
H.460 NAT, Gatekeeper Address and Gatekeeper Port options are enabled to set it.
•
H.460 NAT: Set to On when you use the H.460 standard for NAT and firewall traversal.
•
GateKeeper Address: Enter the IP address of the primary H.323 gatekeeper.
•
GateKeeper Port: Enter the port number of the primary H.323 gatekeeper.
33
NOTE
You can check the registered status in the Server Status menu of the system information window.
•
Security function may not be supported in specific countries.
•
When both Near End user and Far End user are set the AES encryption to enable before call connection
the call screen.
•
Web monitoring is not supported while AES encryption is activated during a call.
3
is displayed during a call on
SIP
This part is used when users attempt to use a SIP server.
•
SIP Transport Protocol: Select the transport protocol to use during sip outgoing call. You can choose AUTO, UDP or TCP. If you select
TCP or UDP, you can make a SIP call with the selected value. If the far site user does not enable the same transport protocol, you can’t
connect to the far site. If you select Auto, you are able to connect moderately with the far site.
Installation
•
34
Installation
SIP Server
This part is used when users attempt to use a SIP server.
3
Installation
•
SIP Name: Enter the name of the device used when making calls with SIP. The SIP name can be used with alphanumeric. If you enter
other characters except letters, numbers, “.”, “-” and “_”, you cannot connect a SIP call.
•
Use SIP Server: Set to On when you use the SIP server. If you set to On, the username, password, register server address, register server
port, proxy server address and proxy server port options are enabled to set it.
•
User Name: Enter the SIP server authorization username.
•
Password: Enter the SIP server authorization password.
•
Register Server Address: Enter the hostname or IP address of the SIP register server.
•
Register Server Port: Enter the IP port number of the SIP register server.
•
Proxy Server Address: Enter the hostname or IP address of the SIP proxy server.
•
Proxy server Port: Enter the IP port number of the SIP proxy server.
Installation
35
QoS
You can specify network Quality of Service (QoS) settings.
3
Installation
•
•
Dynamic Bandwidth: Adjusts the bandwidth automatically for the best video bandwidth available.
--
On: Dynamic bandwidth function is used.
--
Off: Not used.
IP QoS Type: Select the type of TCP/IP Quality of Service (QoS) that your network uses.
--
None: Not used.
--
DiffServ: Set to DiffServ (differentiated services) type of Service (QoS) for audio, video and data packets.
--
IntServ: Set to IntServ (integrated services) type of Service (QoS) for audio, video and data packets of the Service (ToS) preference.
If you select this option, the IntServToS option is enabled to set it.
•
IntServToS: Select IP Type of Services. This helps a router select a router path when multiple paths are available.
•
IntServAudio: Enter the priority of Audio for Intserv Quality of Service (QoS). [Range 0~7]
•
IntServVideo: Enter the priority of Video for Intserv Quality of Service (QoS). [Range 0~7]
•
IntServData: Enter the priority of Data for Intserv Quality of Service (QoS). [Range 0~7]
•
DiffServAudio: Enter the priority of Audio for Diffserv Quality of Service (QoS). [Range 0~63]
•
DiffServVideo: Enter the priority of Video for Diffserv Quality of Service (QoS). [Range 0~63]
•
DiffServData: Enter the priority of Data for Diffserv Quality of Service (QoS). [Range 0~63]
36
Installation
Network Settings
IP
You must set the IP address for the call.
3
Installation
•
Assignment: Set to STATIC or DHCP for your network configuration.
--
DHCP: Select this option when a DHCP server is installed on the network to allow IP address assignment. With this setting, the
IP address is assigned automatically. If you set to this, the IP address, subnet mask, gateway, main DNS and sub DNS options are
dimmed.
--
STATIC: Select this option when you set the network configuration manually.
•
IP Address: Enter the static IP address of the device.
•
Subnet Mask: Enter the subnet mask IP address.
•
Gateway: Enter the default gateway IP address.
•
Main DNS: Enter the Primary domain name server that translates the hostnames into IP address.
•
Sub DNS: Enter the sub DNS server address that backups the main DNS.
Installation
37
Firewall
This function is used when users try to bypass the firewall.
3
Installation
•
NAT Configuration:
--
Disable: Not used with this function.
--
Enable: Select when using the static NAT server to traverse your firewall. If you select this option, the NAT Public Address and Fixed
Port options are enabled.
•
NAT Public Address: Enter the public IP address or hostname of the system.
•
Fixed Port: You can fix the TCP and UDP port range. If you set to On, the TCP port and UDP port options are enabled.
•
TCP Port: Enter the lowest/highest number in the reserved range of the TCP port numbers. (Minimum range of port is 1.)
•
UDP Port: Enter the lowest/highest number in the reserved range of the UDP port numbers. (Minimum range of port is infinite.)
Service
•
Web Server: If you set to On, you can connect to this device using the web browser.
•
Telnet: If you set to On, you can connect to this device using the telnet.
•
SSH: If you set to On, you can connect to this device using the SSH.
38
Installation
SNMP
3
Installation
•
SNMP: Allows administrators to manage the system remotely using SNMP.
--
Disable: Not used with this function.
--
Enable: Selects when SNMP is allowed access to this device. If you select this option, the Trap Host and Community options are
enabled.
•
Trap Host 1 to 3: Specifies the IP address of the computer you intend to use as your network management station and to which SNMP
traps will be sent.
•
Community: Specifies the SNMP management community in which you want to enable this system (e.g. lgecommunity or public).
LDAP
LDAP is the ability to read registered address books in the LDAP server. If you connect to an LDAP server, you can confirm in corporate contact
tab in directory.
•
LDAP:
---
Disable: Not used with this function.
Enable: Selects when the LDAP server allows access to this device.
•
Hostname: Enter the host name or IP address of your LDAP server.
•
User: Enter the username of your LDAP server.
•
Password: Enter the password your LDAP server.
•
Base: Enter the base Distinguished Name (DN) used to query your LDAP server.
•
Filter: Enter filter strings that you use to specify a subset of data items in an LDAP data type.
Installation
39
IEEE802.1x
Specifies whether 802.1X network access is enabled. This systems support the following authentication protocols:
•
EAP-MD5
•
EAP-PEAP
•
EAP-TTLS
3
Installation
•
IEEE802.1x:
--
Disable: Not used with this function.
--
Enable: Select this option to 802.1x user authentication. If you select this option, identity, password and EAP method options are
enabled.
•
Identity: Enter the identity name given to you by your IT administrator. This specifies the system’s identity used for 802.1X authentication.
•
Password: Enter the password given to you by your IT administrator. This specifies the system’s password used for 802.1X authentication.
•
EAP Method: Select the EAP method.
40
Installation
NOTE
When User Use EAP-MD5
If you use EAP-MD5, you do not need to upload any files in the web service.
When User Use EAP-TTLS
1. If you use EAP-TTLS, you must receive ca.pem, client.pem, client.key from the 802.1x network manager.
2. Upload the ca.pem, client.pem, client.key files to the web service of your system as shown in the picture below.
3
Installation
When User Use EAP-PEAP
1. If you use EAP- PEAP, you must receive a ca.pem file from the 802.1x network manager.
2. Upload the ca.pem file to the web service of your system as shown in the picture below.
After Setting 802.1x
1. When you finish these settings, confirm that you can see your IP on the main screen.
2. Perform a ping test in the system info > Network utility > Command.
3. You can now attempt to call other VCS.
Installation
41
Speed/Duplex
3
Installation
•
Assignment: Select the Auto or Manual mode to set the value of Speed/Duplex. When Assignment is set to Auto, the highest priority is
100 Mbps. If you set to the Manual mode, the Speed and Duplex options are enabled.
•
Speed: Select the speed that your network uses.
•
Duplex: Select duplex mode that your network uses.
42
Installation
System Settings
Audio
Adjust settings for audio input and output devices connected to the system.
3
Installation
•
•
•
•
Audio In: Select the audio input to use for the active microphone. --
Microphone: Audio is input via the connected microphone.
--
Line in: Audio is input via the connected Audio device.
Echo Control: Select echo function to ON or OFF.
--
On: Select when you want to turn on the echo cancellation.
--
Off: Select when you want to turn off the echo cancellation.
Audio Out: Select the location for audio output during calls.
--
HDMI: Audio is output via the connected HDMI device.
--
Line Out: Audio is output via the connected audio device.
RingTone: Select the volume level of the ring tones.
--
Off: The ring tone volume is off.
--
Small: The ring tone volume is set to small.
--
Middle: The ring tone volume is set to middle.
--
Loud: The ring tone volume is set to loud.
Installation
43
Management
3
Installation
•
Admin Password: Change the password of the administrator if you want. The password is case-sensitive.
•
System Restart: To restart the system, do the below steps.
1. Select Restart and press OK. The warning window is displayed.
2. Select [OK] and press OK. The system will be restarted.
•
Setup Initialization: You can initialize the configuration of the setup menu.
1. Select Reset and press OK. The warning window is displayed.
2. Select [OK] and press OK. The system will be initialized and restarted.
•
Factory Reset: You can reset the system to its original factory settings.
1. Select Reset and press OK. The warning window is displayed.
2. Select [OK] and press OK. The system will be reset to factory default settings and restarted.
NOTE
d
e.tratser
If you select the [Factory Reset] option, the saved address in the directory and call history will be deleted.
44
Installation
System Information
After the configuration setup, you can view the condition of the system.
Press (INFO) to display the system information.
System Status
You can view the information of the current system status and configuration.
3
Installation
Video
You can check the video condition.
Installation
45
Audio
You can check the audio condition.
3
Installation
How to Test the Audio Output
1. Select the Audio Out Test option using the arrow button.
2. Press OK and select the audio output option between the HDMI and Line Out option.
3. Press OK and select [Start].
4. Press OK again to test the audio output. You will hear sound, then exit the test. If you cannot hear the sound, check the volume level or
connection.
Network Utility
You can troubleshoot network connection issues with your system using the ping and traceroute utilities in Network Utility.
1. Select the IP Address field.
2. Press OK to enter a value. If necessary, use 1/a/A to change the method of text entry for text fields or select the keyboard icon to display
the virtual keyboard. After entering a value, hide the keyboard (if you used it to enter the value) and press OK to exit the field.
3. Select the option of the command menu.
•
Ping: The ping command tests responsiveness between two devices.
•
Traceroute: The traceroute command tests responsiveness and traces the path of a packet from one device to the other.
4. Press Start and press OK to test it.
46
Installation
Server Status
You can view the server status.
3
Installation
Operation
47
4Operation
Before Using the System
Before using the LG VCS device, make sure the connections are correct and verify that a proper power supply is used.
•
Check the connections of the LG VCS device for the correct conditions.
•
Check that the LG VCS device is connected to the network and power is supplied.
•
Before using the VCS, make sure the network settings are correct.
•
Before placing a call, examine the near end video image from the connected camera to your system. If the image flickers, colors appear
unbalanced or the image appears too dark, you may need to adjust the room lighting or camera brightness and white balance and check
the Shutter menu.
Placing a Call
You can place a call from your system to another VCS. Begin a call in one of the following ways:
Placing a Call Manually
You can place a call by entering the IP address manually.
1. Select the Text input field and press OK.
2. Enter an IP address or dial numbers.
Use [
] to change the method of text entry for text input field.
3. After entering a value, press OK.
is selected automatically.
4. Press OK again to place a call. The call status dialog box is displayed.
The call status dialog box shows the number or IP address that you are attempting to call and the status of the call.
4
Operation
•
48
Operation
NOTE
•
If you cancel the call, press OK during the dialing.
•
If the system does not answer the call within about 120 seconds, your system will be disconnected automatically.
•
Check the IP address of the system before you place a call. If you do not set the IP address correctly or set the wrong IP address, you can
not make a call.
•
You can select call speed which is the maximum amount of network bandwidth to use for video call in the main screen.
Multipoint Call (V5500 Only)
You can add the other user during the call.
1.Press
during the call.
2. Follow steps 1-4 described in “Placing a Call Manually”.
NOTE
You can add up to 3 users.
4
Operation
Placing a Call from the Call History
The list of the Call History stores up to 50 recently dialed phone numbers. The oldest entry in the list is automatically removed when the
system receives a call or places a call after the maximum number of entries has been reached. The last call placed always appears first on the
list.
1. From the main screen, press the upper arrow [ ] button. The Call History tab is expanded.
2. Use the left [ ] or right [ ] button to select an entry.
3. Press OK to place a call. The call status dialog box is displayed.
NOTE
•
To cancel the call, press OK during the dialing.
•
If you use the Call History function during the call, you cannot use the Add and Delete function.
Operation
49
Placing a Call from the Directory
The directory stores a list of names and numbers from which you can place calls. To place a call from the directory, follow these steps:
1. From the main screen, press DIRECTORY on the remote control or select [Directory] on the main screen and press OK to access the
directory.
2. Use the arrow buttons to select the entry that you wish to dial.
3. Press OK to place the call. The call status dialog box is displayed.
NOTE
•
Refer to the Directory setting section for more details.
•
If you use the Directory function during the call, you cannot use the Add, Edit and Delete function.
Placing a Call using the Speed Dial
If you set a speed dial number, you can place a call quickly and easily. Press and hold the registered number button for a while until the call
status dialog box appears.
4
Operation
Answering or Rejecting a Call
You can configure your system to automatically answer incoming calls by setting preferences in [User > General > Answer Type] menu as
follows:
•
Auto Answer: If you select this option, the system automatically answers the first incoming call.
•
Manual: If you select this option, you must manually answer incoming calls. If your system is configured for answering calls manually,
choose one of the following options when an incoming call arrives:
•
--
Select [Pickup] and press OK to accept the call.
--
Select [Reject] and press OK to reject the call.
Do not disturb me: If you select this option, you can block the all of the call from the other system. The “Do not disturb” message is
displayed in the middle of the top of the main screen. Missed calls appear in the Call History list. Consider using this feature, for example, if
you are using the meeting room for a purpose other than a video conference and do not wish to be disturbed by incoming calls.
NOTE
If you call to another system with the “Do not disturb” function enabled, the warning window is displayed and the call is disconnected
automatically.
Managing a Call
During a call, you can view information about the status of the call and the identity of the connected caller.
Ending a Call
You can end a call using
on the remote control. Press
when you want to end a call. You will see a pop-up message and then select
one or all when you end a multipoint call.
Hiding or Showing User Interface Elements
To hide or show the user interface elements at any time during a call, press
l
.
50
Operation
Managing Audio
You can adjust the volume of the audio and mute the active microphone.
Adjusting Volume
To adjust the volume in a call, use [VOL + / -] on the remote control. If the volume is set to “0”, audio output is muted and Mute icon
appears in the main screen.
NOTE
If the microphone is too close to the TV or some kind of speaker, Echo Performance can be bad condition.
Muting the Active Microphone
If you press
on the remote control or press
on the microphone, the active microphone is muted in a call. Refer to below table for
mute condition.
Activate
Deactivate
On the screen
Symbol
4
Operation
On the microphone
Managing Video Layout
During a call, video from the connected caller appears in your monitor. You can change the screen layout of near and far end video.
Understanding Screen Layouts
Typically, screen layouts appear as the following types:
•
A far end participant or a presentation appears on the left window.
•
Your site (the near end participant) appears on the right window.
Changing the Screen Layout
1. During a call, press LAYOUT button to display the layout select window.
•
The single point call layout window.
•
The multi-point call layout window.
2. Selects the screen layout using left [ ] or right [ ] button.
3. Press OK to confirm.
Operation
51
Managing Video Contents
Changing the Video Source
You can change Main Camera screen to Contents screen during a call or idle status..
1. Connect the PC to the system with D-sub cable (see page 16).
2. Let out the video out correctly on your PC (e.g. Fn(Function) + F7 (LG laptop only) or Dual monitor setting)
3. Select the near end video and press VIDEO SOURCE. The Video Source Setting window is displayed.
4.Press OK and select [VGA Input] option and then press OK.
4
Operation
5. Select [OK] and press OK. The PC screen is displayed on the near end video window.
52
Operation
Sharing Content
If you want to share contents and camera video to far end site device by the real time during a call, the far end site have to support H.239. And
you should set to H.323 on the [Setup>User>General>Outgoing Protocol].
1. Follow steps 1-2 described in “Changing the Video Source”.
2.Press PRESENTATION.
3. You can select the type of sharing contents using by the Second Display option on the [Setup>User>General>Second Display].
•
If you set to Second display option to OFF, content and Main Camera screen will be displayed in one monitor (or TV).
•
If you set to Second display option to ON, Content and Main Camera screen will be displayed on two monitors (or TV) connected to
each HDMI Port separately. The screen shows below table as the "Video Source Setting" of near end camera.
4
Operation
Video Source Setting
HDMI OUT 1
HDMI OUT 2
Main Camera 1
Camera Screen
Contents Screen
VGA Input
Contents Screen
Camera Screen
HDMI OUT 1
HDMI OUT 2
NOTE
•
This unit supports 640 x 480, 800 x 600, 1 024 x 768, 1 280 x 720, 1 280 x 768, 1 280 x 1 024, 1 400 x 1 050 and 1 920 x 1 080 and 60Hz for
PC output resolutions.
•
If the PC screen can not see properly after D-sub cable insert or remove from the VCS, check the PC video output connection again .
Operation
53
4. During a call, press LAYOUT button to display the layout with presentation select window.
•
The single point call with presentation layout window.
•
The multi-point call with presentation layout window.
Viewing Call Information
4
You can view the call information.
Operation
1. During a call, press (INFO).
The current call information window is displayed on the screen.
•
Call Protocol: Shows the call protocol.
•
Resolution: Shows the resolution, in pixels, of the video image transmitted or received.
•
Video Frame Rate: Shows the video frame rate in frames per second.
•
Video/Audio Codec: Shows the Video/Audio codec used to compress and decompress the Video/Audio.
•
Video Packet loss/Audio Packet loss: Shows the number of packets of data that fail to reach their destination. Packet loss can be caused
by a number of factors, including signal degradation over the network medium, oversaturated network links, corrupted packets rejected
in-transit, faulty networking hardware, maligned system drivers or network applications, or normal routing routines.
•
Video/Audio jitter: Shows the variation, in milliseconds, in the time between packets arriving, caused by network congestion, timing
drift, or route changes.
•
Video/Audio BW: Shows the amount of Video/Audio data transferred per second in kilobits.
•
Cumulative: Shows the up to date count of packets lost in the call.
•
Percentage: Shows packet loss as a percentage of the total packets sent.
2. Press BACK to exit.
NOTE
Call information automatically refreshes every 1 seconds.
Get the Snapshot
During a call, you can get a snapshot of the current video image. It will be displayed in the entry of the Call History list.
Select the far end video window which you want and then press
ll
to take a snapshot.
54
Operation
Managing the Directory
If you have access to the local directory, you can add, remove or edit entries.
4
Operation
Adding an Entry to the Directory
You can create up to 1 000 entries in the directory. To add an entry in the directory, follow these steps:
1. From the main screen, press DIRECTORY on the remote control or select [Directory] button the main screen and press OK to access the
directory.
2. Use the arrow buttons to select [Add] and press OK or press
The Add to Directory window is displayed.
lll
.
3. Use the arrow buttons to select the Name field. Press OK to enter a value.
If necessary, use 1/a/A to change the method of text entry for text fields or select the keyboard icon to display the virtual keyboard. After
entering a value, hide the keyboard (if you used it to enter the value) and press OK to exit the field.
4. Use the arrow buttons to select the Address field. Press OK to enter a value.
If necessary, use 1/a/A to change the method of text entry for text fields or select the keyboard icon to displayed the virtual keyboard.
After entering a value, hide the keyboard (if you used it to enter the value) and press OK to exit the field.
5. Use the arrow buttons to select the Group item and press OK. Select a group and press OK.
NOTE
If you make a new group, do the following steps.
5-1. Select [New] and press OK. The new group window is displayed.
5-2. Enter the new group name and press OK. Select OK of the window and press OK to confirm it.
Operation
55
6. You can confirm saved entry in Speed Dial.
If you want to remove a saved Speed Dial number, you can remove by selecting in the Edit to directory.
6-1. From the main screen, press DIRECTORY on the remote control or select [Directory] on the main screen and press OK to access
the directory.
6-2. Select the My Contact tab using the arrow buttons.
6-3. Use the arrow buttons to move a modifying list and press
6-4. Use the arrow buttons to select the Speed Dial item and press OK. Select a number to delete on the list and press OK.
6-5. Yon will see a pop-up window, then press OK.
lll
.
7. Use the arrow buttons to select a Call Type item and press OK.
Select a call type and press OK.
8. Use the arrow buttons to select the call speed and press OK.
9. When you have completed the settings, select OK and press OK the remote control.
Editing or Deleting an Entry from the Directory
1. From the main screen, press DIRECTORY on the remote control or select [Directory] on the main screen and press OK to access the
directory.
4
llll
or [DEL.]. The Delete Contact window is
3. Modify values in the Edit Directory Entry dialog.
Copying an Entry from the Call History
You can copy an entry from the Call History list to the My Contact list.
1. From the main screen, press the arrow up button on the remote control to access the call history.
2. Select the Call History tab.
3. Select the entry you wish to copy to the My Contact tab.
4. Press
lll
. The Add to Directory window is displayed.
5. Select [OK] of the Add to Directory window. If you want to edit the item, change the value before you save it.
6. Press OK on the remote control.
Copying an Entry from the Corporate Contact
When LDAP is enabled, Corporate Contact is displayed in the Directory.
1. Enter Corporate Contact tab and select an entry and press
2. Copy to My Contact window is displayed. Select [OK].
3. Press OK on the remote controller.
lll
.
Operation
2. Select the entry you wish to edit and press lll .
The Edit Directory window is displayed. If you delete the entry, select entry and press
displayed and you select [OK] and press OK on the remote controller.
56
Operation
Deleting an Entry from the Call History
1. Enter the Call History.
2. Select the entry you wish to delete and press
llll
or [DEL.].
3. The Delete History window is displayed.
4. Select [OK] and press OK on the remote control.
4
Sorting and Searching
Operation
Basically, directories are sorted in the following order: special characters, numbers, characters.
•
All: All entries are displayed.
•
Alphabet: If the first letter of a name in the entries is included in the selected alphabet button, the entries are displayed.
•
Group: If entries are included in the selected group button, the entries are displayed.
•
Search: If the letter or special character in the name is included in the written character on the search field, the entry is displayed.
Placing a Call when the Device is Registered in Gatekeeper Server
Yon can place a call by entering the registered far site name in gatekeeper server.
1. You must confirm registered far site name in gatekeeper server.
2. Select the text input field and press OK.
3. Enter a registered far site name. Use 1/a/A to change the method of text entry for text input field.
4. After entering a value, press OK.
is selected automatically.
5. Press OK again to place a call. The call status dialog box is displayed.
NOTE
•
If you want to cancel the call, press OK while dialing.
•
If you do not answer the call in 2 minutes, the system will disconnect the call automatically.
Making a Call when the Device is Registered in SIP Server
1. You must confirm registered far site name in SIP server.
2. Select the Text input field and press OK.
3. Enter an registered far site name. Use 1/a/A to change the method of text entry for text input field.
4. After entering a value, press OK.
is selected automatically.
5. Press OK again to place a call. The call status dialog box is displayed.
NOTE
•
If you want to cancel the call, press OK while dialing.
•
If you do not answer the call in 2 minutes, the system will disconnect the call automatically.
Operation
57
Using the Camera Control
If the far/near site camera has the PTZ function, you can control the camera.
Idle condition of the near site camera
1. Press
ll
on the remote control. The control icon is displayed on the screen.
2. You can control near site camera by pressing CAM ZOOM +, CAM ZOOM - and Arrow buttons.
During the call
1. Select the site window using the arrow buttons.
2. Press OK on the remote control.
3. You can control the selected site camera by pressing CAM ZOOM +, CAM ZOOM - and Arrow buttons.
4.Press OK to save the settings.
Using Preset function
If the site camera has the PTZ function or another video source, you can use the preset function.
To register the preset position
1. Control the site camera to the location as you want using the CAM ZOOM +, CAM ZOOM - and Arrow buttons. Press OK.
Before you start the preset setting, you should select the site you want to set the preset during the call.
2.Press PRESET on the remote control. The preset window is displyed.
3. Select the preset number you want to save using the left or right arrow button.
4.Press OK to save the preset.
5. Press BACK to exit the preset setting.
or
1.Press PRESET on the remote control. The preset window is displayed.
2. Select the [Select Site] icon and press OK. Select the site you want to set the preset.
3. Select the preset number you want to save using the left or right arrow button.
4. Press
l
on the remote control. The control icon is displayed on the screen.
5. Control the site camera to the location as you want using the CAM ZOOM +, CAM ZOOM - and Arrow buttons.
6. Press OK. Then you will be able to save the location at that number.
7. Press BACK to exit the preset setting.
To use the preset
You can control the site camera to the saved location by selecting the saved number.
1. Press PRESET on the remote control. The preset window is displayed.
2. Select the preset number and press OK. The camera move to the saved location.
Operation
3.Press OK to save the settings.
4
58
Operation
Using SnapShot
You can save entry on directory with the far site user screen picture.
1. Connect to the far site.
2. Press ll on the remote control.
“Snapshot of Far side is saved” is displayed on the screen.
NOTE
•
You can confirm this snapshot information in the Call History.
•
You can save entry with this snapshot information in the My Contact list.
Using Power Off
Press the
the
4
button on the remote control more than 3 seconds, the [Power Off ] window is displayed. Click OK to turn off the software. Press
button again to power on the software. If you power on the software, the screen returns to normal after reboot.
Operation
Operation
59
Using the Web Service
You can perform the same configuration from the web interface that is available from the unit. The web interface contains additional features
that cannot be configured on the unit. You can also update the system, upload certification, import or export address book in the web service.
Login the web service
1. Run the web browser.
The recommended browser is Internet Explorer with Windows.
2. Enter “http://” and the IP address of the VCS in the Address Box.
You can use the Host Name that you entered in the DDNS setup menu of the VCS.
3. Press ENTER on the keyboard and then the LG VCS Web service login page will be displayed.
NOTE
•
Up to 5 users can connect to the Web Service.
•
When you close web service, you should click logout button on the right up side of web page. If you log in and find the below pop-up
message, click OK button and try to log in again after 30 seconds, you can log in.
•
You can change the password on the Web Service. Click the ID where is top right of the main screen. The [Change ID & P/W] window will
be displayed. Enter the [Current Password], the [New Password] and the [Retype New Password] and then Click OK to save.
4
Operation
4. Select the ID and enter the password. The default password is "lge123" for Administrator and "lge456" for User 01 to User 04.
60
Operation
Using the web monitoring function
1. Follow steps 1-4 described in “Login the web service”.
2. Select the [Call Manager] tab. You can show the far end camera video during the call.
4
Operation
NOTE
•
If you find this message “Please Click here to install Active-X component to avail monitoring and refresh.", click the [Click here] and install
the ActiveX program on your computer. After install the Active-X program, you should refresh the web browser. Click the [refresh] and
then click the yellow bar and install the Active-X program again.
•
If setup message still appears despite installation, VLC Player might not be the recommended version. Click the [Click Here] on the “"If VLC
is installed already, Click Here.” message and then check the installation guide.
•
When you find this message “VLC might not be installed, please Click here to install it to avail monitoring.", click the [Click here] to move
the setup page and install the VLC program. Install the recommended version, or recording cannot run. You should access the web
browser again after installation. If the yellow warning bar is displayed, click the bar and install the plug-in program.
•
If video stream is blurred or not clear, please click refresh button on web brower or press "F5" on keyboard. (Internet Explorer Only)
•
Web monitoring is not supported while AES encryption is activated during a call.
Operation
61
Using the web recording function
1. Follow steps 1-4 described in “Login the web service”.
2. Select the [Call Manager] tab.
3. Place a call. The far end camera video is displayed.
4. Click the [CAM Record] button on the Call Manager tab. The initial save folder is “C:\lgvcs\recording”.
If you want to change the folder, select the [Setup] > [Administrator] > [Call] > [General] and set the new folder before you start to record
it. (Target folder is restricted to Local Hard Disk Drive.)
4
Operation
CAUTION
•
LG Electronics is not held responsible for recording failure caused by web recording function.
•
The system may have a problem as VCS or network condition. So you should use the safe recording server for the important conference
session. If you purchase the safe recording server, please contact where you purchased.
•
If call is added or disconnected while recording, recording is halted temporarily and will be restarted with new recording file.
•
Video Clip Information is like as below.
Items
Video Codec
Information
MPG2 - Ffmpeg Decorder
Input / Output Type
MPG2 (0 bits) / YUV2 (16 bits)
Input / Output Size
704 x 576 (1.22:1)
Minimum Disk Space for recording 4 GB
Video Player
VLC media player (See page 60.)
•
Minimal H/W Requirement to use the web recording function Intel Core 2 Duo CPU P8800 2.66GHz 1.57GHz 3.00GM RAM. The Web
service spec recommends Windows XP(Internet Explorer 6.0 and 8.0) and Windows 7(Internet Explorer 8.0).
•
Restart like as below when the recording conflicts occurred.
1. It may cause memory shortage for recording. Reboot the PC.
2. Change the configuration of the control panel firewall in Windows 7 case. Select VLC media player option on the [Control Panel >
Windows Firewall > Allow a program or feature through Windows Firewall > Allowed programs and features(A):] and then check the
check box of Domain, Home/Work (Private) and Public option.
•
Video Frame may be dropped partially according to PC performance when you conduct Web recording.
62
Operation
Upgrading your System Software
To upgrade the software for your system, follow these steps:
1. Follow steps 1-4 described in “Login the web service”.
2. Select the [Setup] tab.
3. Select the [Administrator] > [System] > [Management] option.
4. Click [Upgrade] of the [System Update] option.
4
Operation
5. Click [Browse].
6. Find and open the firmware file.
7. Click [OK]. The system upgrade status bar is displayed.
8. After upgrading is complete, a confirmation window will be displayed.
Click [OK] and the system will be rebooted.
9.
If you use the web service after updating, access the web service again as IP address after the system is rebooted.
NOTE
Before updating, reboot the VCS. Otherwise update may not work properly.
Uploading the Certification File
1. Follow steps 1-3 described in “Upgrading your System Software”.
2. Click [Upload] of the [Upload Certificate File] option.
3. Click [Browse].
4. Find and open the certificate file.
5. Click [OK].
Operation
63
Importing or Exporting the Address Book
4
Operation
Exporting the Address Book
1. Follow steps 1-4 described in “Login the web service”.
2. Select the [Directory] tab.
3. Click the [Export File] menu. The exporting window is displayed.
4. Click [Save].
5. Select the folder and modify the export file name.
6. Click [Save].
Importing the Address Book
1. Follow steps 1-4 described in “Login the web service”.
2. Select the [Directory] tab.
3. Click the [Import File] menu. The Import CSV File window is displayed.
4. Find and open the address book file and then click [OK]. The imported address will be added and you can see the added address on the
list.
5. Import can be performed by Administrator only.
64
Appendix
5Appendix
Troubleshooting
Symptoms
Resolutions
Check the power cable is connected correctly.
Check the input voltage is correct.
The system power does not turn on.
Check the main power switch is turned on.
If the system power does not turn on even if the power cable is connected correctly,
please contact the service center.
5
Appendix
The system power is turned on but
no video data is displayed on the
monitor.
The subject is not clear enough to
see.
Check the input mode of the monitor.
Unplug the power cable and plug in again.
Adjust the camera brightness and white balance in User > Camera tab
Check the batteries.
Make sure that the battery polarity are connected with (+) and (-) matched correctly.
The remote control is not working.
Check the remote control contains two AAA batteries that are in good working
condition.
Verify whether objects are obstructing the sensor on the front of the camera.
Check that the camera cable is connected correctly on device when you use the remote
control.
You can confirm camera connection status as camera icon in main screen
The image is not visible.
Check that the camera cable is connected correctly on device. You can confirm camera
connection status as camera icon in main screen.
If you connect Camera Input HDMI Cable to HDMI TV or Monitor or If you connect Codec
Box's HDMI Out Cable to Camera HDMI Input Port, it can cause malfunction (Color noise
or not visible). So Check HDMI Cables Connection.
Muffled audio reception from the far side may be caused by highly reverberant rooms.
If you are experiencing poor audio reception, add more sound absorbency to the room
and speak in close proximity to the microphone.
The sound is not audible.
Ensure both ends are not muted. Verify that the audio out cables are properly connected
to the monitor and that any external speaker systems are powered and configured
correctly. Also check your Audio Out setting on your audio device (HDMI, Line-out).
Make sure your Audio Out preference in [Admin > System > Audio] for your sound
device. If you are unable to hear the ringer when an incoming call arrives, adjust the ring
tone preference in [Admin > System > Audio].
The system does not work with the remote
control.
Reboot the system that is not responding to commands from the remote control.
Appendix
Video or audio are poor.
After connecting to a call, if audio or video do not display normally, users can attempt to
connect after the codec box is set to low bandwidth.
You hear a distinct echo.
If You Use HDMI TV or Monitor
•
Adjust the volume of the HDMI TV or monitor so that it is not too loud.
•
Adjust that microphone location is not too close to the HDMI TV or monitor.
(1 m or more)
•
Run the Audio out test at the [System info > Audio] menu.
65
If You Use External Speakers
You cannot make a call.
•
Adjust the volume of the external speakers so that they are not too loud.
•
Adjust that Mic location is not too close on External speaker (approximately 1 m or
more).
If a call does not successfully connect, verify that you have dialed a working number and
that the far end destination is powered on and available. Verify that the network is ready
and available. Network status is indicated at all times on the main screen.
You can confirm that you can connect from your local IP to remote site IP by using the
ping function in the Network utility.
You confirm that you are using proper call protocol (H.323 or SIP). If you set H.323 or SIP
about outgoing protocol, the far site device must be set to the same protocol like near
site.
If you can’t solve this problem, please contact the service center.
Can not see the PC screen after pressing
[VIDEO SOURCE] or [PRESENTATION].
•
Try to call using lower video bitrate (e.g. Setup > Admin > Call > General > Maximum
Bandwidth).
•
Check with each site’s IP operators that your video UDP traffic is NOT being blocked
by IPS (Intrusion Protection System).
•
Check the remote user’s VCS video capability.
--
What video resolution is supported: HD 720p, SD 720x480
--
What video codec is supported: H.264, H.263, H.264HP
•
Check that the D-sub cable is connected properly between the PC and the VCS.
•
Check that the PC’s video out resolution is properly selected (e.g. 640X480, 800x600,
1024x768, 1280x720, 1280x768,1280x1024, 1400X1050 and 1920X1080).
•
Make sure that you let out the video out correctly on your PC (e.g. Fn + F7 or dual
monitor setting).
The PC screen is shifted after [VIDEO SOURCE]
or [PRESENTATION] has been pressed.
Check that the D-sub cable is connected properly between the PC and the VCS.
I can’t access the web server.
•
--
Change the D-sub cable.
Check your VCS device’s network accessibility.
1) Check the IP address, subnet, and gateway for typos when using a static IP.
2) Check that the IP address is correctly shown on the OSD using DHCP IP.
3) Connect a different PC to the same network and try to ping to your VCS IP address
(e.g. ping 10.177.217.22).
•
Try to disable / enable the web server menu via Setup.
1) Go to Setup > Admin > Network >Service > Web Server.
2) Set Off and exit from setup.
3) Go back to the Web Server setting, set to On and return to the main screen or try
to turn the power off then back on again.
The remote user is not able to hear your voice.
Check microphone status (see page 28).
The current input video of the local camera
displays the flickering image.
Use Shutter function to match your lighting conditions in [User> Camera] menu.
5
Appendix
Severe freezes and broken video during call.
66
Appendix
The call is connected by audio only
although you set to [Audio+Video] on the
[Setup>User>General> Call Mode].
Check the remote user’s VCS video capability.
The call is connected by audio only in case the codec which supported LG VCS is not
compatible with the video codec of Far End user.
--
What video resolution is supported: HD 720p, SD 720x480
--
What video codec is supported: H.264, H.263, H.264HP
Open Source Software Notice
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://
opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for
download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution
(such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the
date on which you purchased the product.
5
Appendix
Appendix
67
Specifications
ITEM
Communication
Video
V5000, V5500
Signal Protocol
H.323, SIP
Multi way call
1 to 3 (inner MCU)(V5500),
1 to 1 (V5000)
Video standard
H.263, H.264BP, H.264 HiP
Resolution
VR5010H
1 to 1 (VR5010H)
All resolutions progressive Scan
All resolutions at 30fps
CIF/SIF
4CIF/4SIF
1280x720p
Camera
Camera type
720p, 30 fps
Zoom
x12 optical
Focus
Auto
Pan/Tilt range
6 degree to 72 degree
x7 optical
11 degree to 72 degree
±100˚ / +20˚ ~ -30˚, FOV 72˚
Backlight (WDR)
YES
Min. Illumination
15 lx (F1.6) with 50 IRE
IR Detector
1/2.8 Type 3M CMOS / F1.6
(wide), 2.2(tele)
YES
interface
HDMI, D-Sub to RJ45 for Signal and Power
Standard
G.711, G.722, G.722.1, G.722.1C
Features
Ring tone
Full duplex for natural conversations
Echo cancellation for echo-free calls
Automatic noise reduction
Automatic gain control
Other Supported Standards
H.323, H.224, H.281 H.225, H.245, H.241, H.460, H.239
Contents sharing
Dual Stream contents sharing
User Interface
Graphic base easy User Interface
Graphical User Interface Call Manager
Snapshot / Thumbnail display
up to 15 languages
5
Appendix
Resolution
View range
Audio
1/2.8 Type 3M CMOS / F1.6
(wide), 2.3(tele)
68
Appendix
Network
IPv4
AES
NAT / Firewall Client (H.460.18/19)
IP Precedence for QoS
Intserv (Integrated Service), DiffServ (Differeniated Service) for QoS
Adaptive QoS, bitrate control(frame rate, resolution control)
Lost Packet Recovery for QoS
Dynamic bandwidth allocation for QoS
Directory & Address Book
Up to 1 000 local directory entries
Save, Remove Redial List features
Missed call notification
LDAP support / H.350 compliant
System Management
Web-based system management
SNMP v1/v2
5
Network Time Protocol (NTP)
Appendix
Firmware Upgrade via Web
Recording
Web Recording
Security
Secure password authentication
Ability to disable HTTP services
H.235 (AES) encryption support including strict compliance
SSH and Telnet services
IEEE 802.1x support
Kensington Security Slot™
Environmental
Data(Camera)
Operating temperature
Operating Humidity
15 % to 80 %, non-condensing
Storage temperature
-20 ˚C (-4 ˚F) to 60 ˚C (140 ˚F)
Storage humidity
Environmental Data(Codec)
Operating temperature
15 % to 80 %, non-condensing
0 ˚C (32 ˚F) to 40 ˚C (104 ˚F)
Operating Humidity
15 % to 80 %, non-condensing
Storage temperature
-20 ˚C (-4 ˚F) to 60 ˚C (140 ˚F)
Storage humidity
Dimensions
(Camera)
0 ˚C (32 ˚F) to 40 ˚C (104 ˚F)
15 % to 80 %, non-condensing
Width
215.5 mm
219.7 mm
Depth
144 mm
149.1 mm
Height
154.5 mm
159.7 mm
Weight
1.55 kg
1.48 kg
Appendix
Dimensions
(Codec)
Width
400 mm
Depth
187 mm
Height
42 mm
Weight
3.0 kg (Without Stand: 2.35 kg)
Interface
69
Audio Input (2 x MicPod, 1x RCA)
Audio Output 1x RCA
Camera Input (1 x HDMI)
D-Sub Video In (1 x VGA )
HDMI Video Out (2 x HDMI 480p, 720p),
2nd Video Out supports the contents only
LAN Port :1 x RJ-45, 10/100/1000 Mbps
Power (1 x DC Input)
MicPod
3.5 mm Micpod with Mute
Power Adaptor
FSP060-DBAC1
Type/model
Input
Rating
Output
AES function may not be supported in specific countries.
DC 12 V, Maximum 5.0 A
5
Appendix
NOTE
100-240 V~, 50/60Hz,1.5 A
Download PDF

advertising