LG | GCE-8160B | LG GCE-8160B Owner’s Manual

Questo manuale include il tagliando di
garanzia. (pagina
ENHANCE
D
BZ03
n.
I-15)
GCE-8160B
CAUTION
The laser used in the CD-R/RW drive
:
Do not
attempt
to open the
can
damage
To reduce the risk of electric shock, do not
No user-serviceable
Refer
your eyes.
cover.
remove cover
(or back).
parts inside.
service
servicing
to
qualified
Use of controls
or
performance
of
personnel.
procedures
other than those
specified
here in may result in hazardous radiation exposure.
WARNING
:
To reduce the risk of fire
to rain
Industry
Canada
or
or
electric shock, do not expose this
appliance
moisture
requirement
This class B
digital apparatus meets
Causing Equipment Regulations.
Cet
appareil numerique
sur
le materiel brouilleur du Canada.
all
de la classe B
requirements
respecte
of the Canadian Interference-
toutes les
exigences
du
Reglement
FCC COMPLIANCE STATEMENT
Note
:
This
equipment has been tested and found to comply with the limits for a Class
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
B
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this
sion
-
-
does
cause
be determined
harmful interference to radio
the
or
televi-
off and on,
reception,
by turning
equipment
is encouraged to try to correct the interference by one or more of
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the
-
equipment
which
can
user
the
the
receiver is connected.
-
?
?
Consult the dealer
or an
Authorized Service Center for
help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This CD-R/RW Drive is for use only with UL listed personal computers that have
installation instructions detailing user installation of card cage accessory.
i
This
product
is manufactured to
of EEC DIRECTIVE
CAUTION
-
requirements
INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM.
VARNING-OSYNLIG
AR
with the radio interference
comply
93/68/EEC and 73/23/EEC.
89/336/EEC,
LASERSTRALNING NAR
DENNA DEL
AR OPPNAD STRALEN
FARLIG.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
PC DOS is
a
LASER
LASER
LASER
LASER
PRODUCT
PRODUKT
LAITE
APPARAT
trademark of IBM Inc.
Roxio and the Roxio
logo
are
trademarks of the Roxio
MS-DOS, Windows, and Windows
and other countries
by
95
the Microsoft
are
trademarks
Corporation.
registered
in the United States
Corporation.
The company names and product names written in this manual
registered trademarks of the respective companies.
This unit
uses
CD-ROM discs with the
When you use this unit as a CD
discs with the following mark
following
player,
This unit
uses
CD-R discs with the
This unit
uses
CD-RW discs with the
This unit
uses
use
are
trademarks
or
mark
compact
following
mark.
Recordable
following
mark.
ReWritable
High Speed
CD-RW discs with the
following
mark.
ReWritable
WARNING:
Only
Disc ReWritable
CD-RW drivers
High Speed"
can
(such
write
as
the
HighSped
GCE-8160B) bearing the logo "Compact
High Speed CD-RW media.
or erase
High Speed CD-RW Media may be recognized by the same "Compact Disc ReWritable
High Speed" logo on the disc label or packaging material, or by the fact that it lists recording
speeds of "4X to 10X, or "Up to 10X"
Attempted writes to High Speed CD-RW media using CD-RW drives
logo "Compact Disc ReWritable High Speed" may result in data loss.
ii
NOT
bearing
the
Contents
Introduction
Features...................................2
ImportantPrecautions........................3
SystemEnvironment.........................4
LocationandFunctionofControls.
Installation
.
.
.
.
.
.
.
.
.
.
.
.
.5
InstallingtheDrive...........................6
DeviceDrivers.............................11
Operation
HowtoUsetheDiscs........................12
Appendix
Troubleshooting............................13
Specifications..............................14
Warranty..................................15
Thank you for
purchasing
Features
this
OPC*
?
Running
bility.
?
Enhanced-IDE
?
Power
CD-R/RW Drive.
gives
a
(ATAPI)
flatter
writing signal
that
improves
relia-
interface.
tray loading and ejection of disc.(The disc
can
also be
ejected manually.)
?
The recorded CD-RW media
a
?
?
?
can be played in a DVD player or
Player, maintaining future compatibility.
easy writing to CD-RW discs.
multiread CD-ROM
Supports
Supports
UDF for
Windows 95, 98, 2000 & ME/NT4.0
16XRecord/10XReWrite/40XRead
Writing speed depends
As
a
labelled
?
on
capabilities
of discs.
result, for high speed write/rewrite, you should
high speed
use
media
ReWritable discs
Automatic buffer underrun
error
prevention technology
-
"Super
Link".
*
Continuously
monitors the
laser power to
Package
Items
signal
level
during recording
compensate when the disc is dirty, insuring
Item
-
-
-
-
-
-
-
-
and
a
flat
1
CD
1
Recording Software
Blank CD-RW Disc
1
E-IDE
1
cable
Audio Cable
1
Mounting Screws
4
Manual for CD-R/RW Drive
1
Manual for CD
1
Recording Software
the
signal.
Quantity
Internal CD-R/RW Drive
(ATAPI)
adjusts
Important Precautions
Follow these
Precautions
?
precautions
when
discs.
or
Please take notice that the manufacturer of this
equipment does
warranty against
inappropriate
installation or handling, or direct or indirect damages.
Please take notice that the manufacturer will bear no responsibility
for direct or indirect damages caused by the use of this product or
not offer any
?
the drive
handling
data loss due to
its malfunction.
?
Please take notice that the manufacturer will bear
for
?
to data caused
damage
Please backup (copy)
responsibility
no
this
by
product.
important data
all
protection against
as
data loss.
Installation
?
Avoid
-
-
-
-
-
placing
the drive in
high temperature
mechanical vibration
direct
sunlight
Don't
move
causing
?
Make
to
?
horizontal
suddenly
from
a
cold
vertical
or
to
place
position.
a warm one or
occur,
operation.
remove
the disc before
moving
may be damaged, causing data loss.
Be careful to prevent foreign objects, such
the drive. In
the drive. The disc
liquids
as
or
metal,
enters the
entering
please consult the
Don't interrupt the
drive,
foreign object
dealer where the drive was purchased.
electric power while the drive is operating.
When
two IDE devices to the
connecting
connectors, make
both
Master,
or
sure
both
Windows may fail to
?
a
temperature suddenly. Condensation may
abnormal
sure
the drive in
position.
the drive
room
from
?
using
it in tilted
use
raise the
?
to:
subject
excessive dust
Do not
?
location
high humidity
We recommend
Operation
a
The total
(about
length
45
cm).
case a
Primary
that the two devices
are
Slave.
both
run or
If
they
recognize
are
or
not
Secondary
configured
set
as
the same,
the drives.
of the IDE cable should be
no more
than 18 inches
Environment
System
Computer
This unit
be
can
operated
in the
system environment explained
here.
233MHz
CPU
System
requirements
(or faster) Pentium (for 16x speed,
faster recommended)
350MHz
or
Windows 95/98
Memory
:
64MB
or
greater.
Windows NT Workstation Ver. 4.0: 64MB
greater (128MB
or over
Windows 2000: 128MB
over
recommended)
or greater(256MB
or
or
recommended)
Windows ME: 64MB
or
greater
Hard disk with average access time of 19 msec
or less, and data transfer speed of 2400KB/sec
Hard disk
greater. 75MB or more free space.
(The free space needed for writing depends
the quantity of data.)
or
Enhanced-IDE interface
Interface
Secondary
Drive
bay
5.25-inch
Power
Software
Master
or
(as Primary Slave,
Slave)
half-height bay required
+5V/+12V power socket
Required
OS
Windows
CD-R, CD-RW discs
CD-R
:
Occasionally
or
later
Ricoh, Mitsubishi Chemical, Verbatim,
Taiyo Yuden, Fugi Film, Kodak, or Imation
discs
CD-RW
required
95/98/2000/ME, Windows NT
Workstation Ver.4.0
*
on
:
are
recommended.
Ricoh, Mitsubishi chemical, Verbatim,
Imation, Sony discs are recommended..
the CD-R and CD-RW discs written
by other CD drives*.
read using the CD-R/RW
by
the CD-R/RW
drive cannot be read
These unreadable discs
may need to be
written.
drive
The disc written
by
using
on
which
require
the CD-R/RW drive
CD-ROMs other than Multi-read
might not be readable
compatible (UDF compatible)
CD-ROMs.
Multiread
Software
compatible (UDF compatible)
1. CD-ROMs that
can
2. CD-ROMs that
support Packet Write.
Install the
supplied
CD
CD-ROMs
are:
read low reflectance.
Recording
Software before
using
this unit.
DirectCDTM v2.5b(s)
Location and Function of Controls
Front Panel
7
6
EAD
READ
RITE
WRITE
12
1.
34
7. Drive
Headphone jack
activity indicators
Two colored LEDs
2. Volume control
the
Emergency Eject Hole
4. Play/Skip button
5. Stop/Eject button
3.
6. Disc
5
(1)
are
used to indicate
of CD-R/RW Drive.
operation
Read
The orange color is
displayed when the
begins the Spin up operation: accessing data, reading data,
playing Audio, and up loading tray.
(2) Write
The green color is flashed during disc
writing sessions.
spindle
tray
motor
Rear Panel
POWER
ANALOG
DIGITAL
AUDIO
AUDIO
CSM
RGL SLA
INTERFACE
1
+5
GND
+12
2
39
40
DG
123
4
5
3.
Digital Audio Output Connector
Analog Audio Output Connector
Jumper Connector
This jumper determines whether the drive is configured as a master or slave.
Changing the master-slave configuration takes effect after power-on reset.
4.
IDE Interface Connector
1.
2.
Connect to the IDE
(Integrated
Device
Electronics)
Interface
using
a
40-pin
flat IDE cable.
NOTE
could
:
Do not connect
cause a
OFF when
5.
5
disconnect the cable when the power is on, as this
damage the system. Always turn the power
disconnecting the cable.
or
short circuit and
connecting
Power Connector
or
DirectCDTM v2.5b(s)
Installation
the Drive
Installing
Before
Before
the drive,
installing
You will need the
Installation
?
A
please
following:
driver of
screw
note the
following points.
suitable size to fit the
a
securing
screws
for the
drive unit.
?
The manual for the
computer,
so
you
can
find the
mounting
for the IDE controller cable.
positions
Turn off all
peripheral appliances of the computer and the computer
itself, and disconnect their power cords from the wall sockets.
Discharge
any static
computer
covers, etc.
Make
Removing
the
sure
computer
Computer
Cover
NOTE
avoid
Mounting
all
:
remove
for details about
There may be
the
removing
sharp edges
your person
by touching
the
computer and the computer itself
cover.
the
Refer to the manual for the
cover.
inside the
computer
take
so
care
to
injury.
1. Remove the 51/4′′ drive
the Drive
on
devices of the
peripheral
turned off, and then
are
electricity
manual for the
bay panel
from the
computer. Refer
to the
computer for details.
2. Insert the drive unit into the
the cables inside the
bay.
Do not
apply
excessive pressure to
computer.
3. Secure the drive with the
screws
provided.
If there is not
enough
space behind the drive, connect the IDE and other cables before
securing the drive.
EAD
WRITE
READ RITE
NOTE
:
This is
a
different, please
devices.
6
general
installation
guide.
If your PC hardware appears
consult your hardware manual for
installing peripheral
DirectCDTM v2.5b(s)
Connect the power cable from the computer's power supply to the socket
the drive unit, fitting the connector firmly into the power in connector.
Connecting
on
the Power
If there is
to
Connector
no
purchase
spare power cable available in the computer, you will have
splitter cable of a suitable type.
a
POWER
+5
POWER
DIGITAL
AUDIO
+5
1
INTERFACE
ANALOG
AUDIO
CSM
GND
GND
+12
+12
2
39
40
RGL SLA
DG
Beveled
edge
up
NOTE : Improper connection may damage the drive and void
Generally, the Power connector can only fit one way.
Connecting
Connect the 40
making sure
to pin 1 on
the
the
warranty.
IDE cable to the back of the CD-R/RW Drive,
(red) stripe on the IDE cable is connected
pin
the coloured
the CD-R/RW drive.
Pin
1
is closest to the Power
Connector.
Interface
NOTE
Connector
:
the IDE connector is
Generally,
DIGITAL
AUDIO
ANALOG
AUDIO
CSM
INTERFACE
1
2
+5
keyed
and will
only fit one way.
POWER +12
GND
Pin1
39
40
RGL SLA
DG
Red-edge
Connecting
If the
computer is using
sound card with
the Sound
an
most sound cards
a
sound card, the drive is connected to the
supplied analog audio cable fits
audio cable. The
or one can
Card
be
purchased
at
a
local
computer
Refer to the manual for the sound card for detailed
information
regarding
connection.
DIGITAL
AUDIO
DIGITAL
AUDIO
ANALOG
AUDIO
CSM
RGL SLA
DG
ANALOG
AUDIO
RGL
INTERFACE
CSM
SLA
39
40
POWER
12
+5
GND
+12
39
40
DG
marking
LR
Sound card
7
L-R
store.
DirectCDTM v2.5b(s)
Before installation, set the
Jumper
Setup
rear
jumper
on
the
jumper
connector
on
the
panel.
The drive
be connected
can
as
the Master
or
Slave
on
an
EIDE
interface. When several
(ATAPI)
nected, each
must be set in
a
(up to four) EIDE devices are conunique way. Specific knowledge of
hardware and software is necessary to install the drive.
NOTE
If two
:
peripheral devices with the same settings
Primary or to the Secondary EIDE bus,
connected to the
computer may fail
to
run
or
both
are
the host
may malfunction. Careful attention is
necessary.
CS: Cable
Select(CSEL)
SL: Slave
POWER
INTERFACE
DIGITAL
AUDIO
ANALOG
1
+5
GND
+12
MA: Master
2
39
AUDIO
CSM
RGL SLA
40
DG
UDIO
CSM
GL
NOTE
If
more
Only
:
than
39
40
SLA
jumper should be installed on the jumper connector.
jumper is installed, the drive may malfunction or be
one
one
damaged.
Master/Slave setting is determined by jumper installation on the
Jumper Connector. The following table shows the possible jumper
settings.
Name
MA
Function
Drive set
as
Master
Drive set
as
Slave
C
S
M
S
L
A
(Master)
SL
(Slave)
CS
Drive mode set
(Cable Select)
host IDE interface
If you use CSEL setting,
automatically, depending
by
CSEL
the
the MASTER/SLAVE
on
the hardware
For details refer to the manual of your
8
on
setting will
configuration.
computer.
be made
DirectCDTM v2.5b(s)
The CD-R/RW drive connects to the motherboard of the host
PC
puter using
Connection
To Install
a
Drive
as a
an
Slave
or
To install the drive
as
from the
Master
Master device,
as a
depending
Master, the jumper
on
can
your computer.
be left
as
supplied
factory.
Master drive
Drive
com-
IDE interface cable. You may connect the CD-R/RW
hard
(Booting
Master drive
disk)
DIGITAL
ANALOG
AUDO
AUDIO
DR GL
G3
CSM
9
40
SLA
INTERFACE
POWER
+5 GND
+12
1
2
(CD-R/RW drive)
(Jumper left as
MAster)
Motherboard
Secondary
Primary
connector
connector
-ORMaster drive
(Booting
hard
disk)
Master drive
(CD-R/RW drive)
(Jumper left as
MAster)
I
D
GTAL
AUDO
ANALOG
AUDIO
G
DR
GL
CSM
SLA
39
INTERFACE
40
POWER
1
+5
GND
2
+12
DIGTAL
AUDO
ANALOG
AUDIO
G
DR
GL
CS
SL
E
POWER
1
2
+5
GND
+12
Slave drive
(Other
IDE
drive)
Secondary
Primary
connector
connector
NOTE
:
A hard disk is
the EIDE
(ATAPI)
normally
hard drives and CD-ROMs
9
installed
interface. Other EIDE
are
then set
as the Primary Master
peripheral devices such
differently.
on
as
DirectCDTM v2.5b(s)
To Install
To install the drive
as
rear
a
Slave
panel
Slave, change the jumper setting
as a
the
on
to SL.
Master drive
Drive
(Booting
DIGITAL
AUDIO
hard
disk)
ANALOG
AUDIO
G
DR
GL
C
SL
E
POWER
1
2
+5
GND
+12
Slave drive
(CD-R/RW drive)
(Jumper set to
SLave)
-OR-
Master drive
(Booting
hard
disk)
Master drive
(Other
IDE
drive)
DIGTAL
AUDO
ANALOG
AUDIO
G
DR
GL
CSM
SLA
39
40
INTERFACE
1
2
DIGITAL
AUDO
POWER
GND +12
+5
ANALOG
AUDIO
G
DR
GL
CS
SL
E
POWER
1
2
+5 GND
+12
Slave drive
(CD-R/RW drive)
(Jumper set to
SLave)
Secondary
Primary
connector
When the installation of the drive unit is
Replacing
computer
the
Computer
Cover
10
cover.
con-
nector
complete, replace
the
DirectCDTM v2.5b(s)
Device Drivers
When
Windows 95/98/2000/ME
using
Workstation Ver.4.0,
no
special
or
Window NT
device driver is
required.
Your
system, upon Power On and bootup after installing and
connecting the new CD-RW drive, will recognize and load native
software drivers
automatically.
The DOS and Windows 3.1
drivers
anytime
users can
download the DOS Device
via internet.
For your information,
please consult the following
http://www.lge.com
http://www.lgeservice.com/drivers.html
For
In order to
ensure
normal drive
internet sites:
check the
operation, please
following:
Windows
?
95/98/2000
The drive is
displayed in
: [Control Panels]-[System]-[Device Manager]-[CD-ROM]
Windows 2000 : [Control Panels]-[System]-[Hardware]-[Device
Manager]-[DVD/CD-ROM-Drive]
32-bit is displayed in
[Control Panels]-[System]-[Performance]
Windows 95/98
Users
?
If the drive is not
following
?
If
recognized by
your computer,
please
check the
items.
displayed on the IDE controller in [Control
Panels]-[System]-[Devices Manager]-[Hard Disk Controller],
a
indicator is
you will need to contact your PC's manufacturer
motherboard's manufacturer and
get
the
or
the
appropriate
IDE
controller driver.
Run Add New Hardware in Control Panel to let PC search
for
For
new
In order to
ensure
the drive is
normal drive
displayed on
[SCSI Adapter]-[Devices]
Windows
NT
again
device.
operation, please check to see if
[Control Panels]-
the IDE controller in
If the drive is not recognized by your computer, a
indicator is
displayed on the IDE controller in [Control Panels]-[SCSI
Adapter]-[Devices], you will need to contact your PC's manufacturer
or the motherboard's manufacturer and get the appropriate IDE
Workstation
Ver.4.0 Users
controller driver.
11
DirectCDTM v2.5b(s)
Operation
How to Use the Discs
When
CD-ROM discs, CD-R discs
using
attach any stickers
attached not
only
or
causes
may be lost due to
or
labels to the discs.
CD-RW discs, don't
Using
discs with them
read and write errors, but data
damage
on
the disc
to the disc itself.
The Discs in this unit
DO NOT
unit may be
DO NOT
or
Emergency
Eject
operate at a very high speed!
damaged, cracked or warped discs. The
damaged if they break.
use
use
store data
non-standard discs. NON-standard discs may not
a
feature that allows the CD to be
this becomes necessary in
drive or a power outage.
use
an
this feature
Turn the power to OFF.
Poke a fine-tipped object
1)
2)
optical
play
properly.
This drive has
NOTE: Don't
drive's
ejected manually
emergency, such
except in
(such
as
an
a
as
if
failure of the
emergency.
straightened heavy duty
into the small hole above the
paper clip)
eject button. The front
door will pop open and the disk tray will come partway out.
Pull the front door to open it all the way, then grip the disc tray
between thumb and forefinger and gently pull it straight out.
3)
READ
RAD
NOTE: This feature is
a
last
WRITE
measure
to
be used
emergency. Using it excessively will cause malfunction.
If you cannot get a good grip on the disc tray with your
*
a
12
steel binder
clip
or
spring clamp
to
pull
it out.
in
an
fingers,
use
only
Troubleshooting
Before
Requesting
Before
?
Service
?
calling
for service, check this list.
The drive doesn't have power.
?
Is the power
?
Is the Power Connector to the drive
The
?
?
?
supply
system doesn't
cable from the host
computer plugged in?
attached?
securely
start.
Are the
Primary and Secondary connections and the
and Slave settings correct?
Is the total length of the IDE cable 18 inches or less?
Is each connector completely attached?
Master
Movement of the PC may loosen connections.
?
Cannot Read
?
or
Write Discs.
Is the condition of
disc, and others)
page
everything
as
else in the
it should be?
system (CPU, hard
(See system
environment
4.)
?
Does the CD-R
?
Did
or
CD-RW disc have dirt
a screen saver or
other
scratches?
or
application operate
while
writing
to
the disc?
?
Is there
?
Does
?
enough free space on the CD-R/RW disc?
writing fail even using the simulation test?
Is the disc loaded in the drive with the read/write surface
the
right
direction?
?
Is the drive installed in the correct orientation?
?
Was the drive
to
a
or
disc moved from
high temperature
condensation
on
facing
(label up)
a
low
environment?
the lens in the drive
temperature environment
is
(There
or on
a
possibility
of
the surface of the
disc.)
When you call for service, be
of your
as
much information
environment, and the
specific problem.
going on? Were
prepared
to
give
possible
system,
(What happened? When? How long? What
there any error messages displayed? etc.)
as
was
DirectCDTM v2.5b(s)
Specifications
Type
Internal
Interface
Enhanced-IDE
Data buffer memory
2MB
type (bare drive)
(ATAPI)
Disc diameter
12cm, 8cm, standard size CD's
Data Transfer Rate
?
Sustained
Read
:
Write
:
16 to 40x CAV: 2.4MB to 6.0MB/s
CD-R
:
4x: 600KB/s
CD-RW
:
2x: 300KB/s
8x: 1200KB/s
4x: 600KB/s
12x: 1800KB/s
10x: 1500KB/s
16x: 2400KB/s
?
Burst
(ATAPI)
16.67MB/s
Average
access
Mounting
Mode 4, MULTI-DMA Mode
Format
formats
<Write>
CD-ROM
??
CD-Extra
??
?
CD-ROM XA
??
?
Photo CD
CD-I
??
CD-ROM+CD-DA
??
?
Video CD
??
?
DC5V, DC12V
Less than
2lbs.(0.90Kg)
5.75"x7.27"x1.63"
(146
x
184.7
x
41.3
mm)
Error Rate
10-12 bits
MTBF
120,000 hours Power On Hours (Duty Cycle 10%)
MTTR
Audio
or
less
Within 30 minutes
Output
Level
Line out
:
0.7 Vrms at 47 kohm
Headphone
0.6 Vrms at 32 ohm
:
Environmental Conditions
When
Temperature
5 °C to 40 °C
Humidity
The drive's appearance and
14
?
??
Tray type (automatic loading/eject)
(WxHxD)
<Play>
??
Power
Weight
<Read>
CD-DA
Loading system
Dimensions
2)
<Typical>
Horizontal/Vertical
direction
Compatible
(PIO
Random 110ms.
time
When not
operating
(No
air
cooling)
operating
-20°Cto60°C
10% to 80% R.H.
10% to 80% R.H.
(No condensation)
(No condensation)
specifications
may
change
without
prior
notice.
CD-R/RW LIMITED WARRANTY
will
repair or at its option replace*, without charge, your product which proves to be
workmanship under normal use, during the warranty period listed below from
original purchase.
material
or
defective in
the date of
WARRANTY PERIOD
Div.
MODEL #
Personal
GCE-8160B
Labor & Parts
or
producing
Commercial
producing
Non-Income
1 Year
use:
or
Income
90
days
use:
No other express warranty is applicable to this product. THE DURATION OF ANY IMPLIED
WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO
THE DURATION OF THE EXPRESS WARRANTY HEREIN. WE SHALL NOT BE LIABLE FOR
THE LOSS OF THE USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR INABILITY TO
USE, THIS PRODUCT OR FOR ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY,
INCLUDING THE
IMPLIED WARRANTY OF MERCHANTABILITY APPLICABLE TO THIS
PRODUCT.
Some states do not allow the exclusion
or
limitation of incidental
or
consequential damages
or
limitations on how long an implied warranty lasts; so these limitations or exclusions may not apply to
you. This warranty gives you specific legal rights and you may also have other rights which vary
from state to state.
THE ABOVE WARRANTY DOES NOT APPLY:
1.
2.
3.
4.
To
damages or problems which result from delivery or improper installation.
To damages or problems which result from misuse, abuse, accident, alteration, or incorrect
electrical current or voltage, maintaince conditions.
To service calls which do not involve defective workmanship or material and explaining the
operation of the unit.
If the serial number of the drive is defaced or missing.
Therefore these costs
are
paid by the
consumer.
CUSTOMER ASSISTANCE NUMBERS:
If you have questions about using this product, check your user's manual first. You will find answer
to most of your questions there. If you need futher assistance, please contact us. We offer the
following support and information services.
To Prove
Warranty Coverage:
Retain your Sales Receipt to prove date of purchase.
of your Sales Receipt must be submitted at the time
Copy
warranty service is provided.
To Obtain Product, Customer,
or Service Assistance:
Call 1-800-243-0000 24 hrs/7
Push appropriate menu code.
or
For
*
Exchange
http://www.LGEservice.com/techsup.html
for support
by
E-mail.
Call 1-800-243-0000 (Mon~Fri8am~5pmCST)
Push appropriate menu code.
Replacement is a factory-reconditioned unit.
period. Factory-reconditioned units
year warranty expires.
one-year
*
Service:
days
Free
are
replacement applies only
available at
Although the information (specifications, contacts, etc.)
anything in this manual is subject to change without prior
was
a
low, fixed
within the initial
cost after the
correct at the time of
notice.
one-
printing,
ⓒ 2001
Copyright
LG Electronics U.S.A. Inc.
1000
Ave.
Sylvan
Englewood
Cliffs
NJ 07632 U. S. A.
LG Electronics Canada Inc.
235
Superior Blvd, Mississauga
Ontario, Canada
LG Electronics Deutschland GMBH
Jakob-Kaiser-Straße 12,
D-47677
Willich, Germany
LG Electronics U. K. Ltd.
LG
House,
Slough
264 Bath
Road,
Berkshire SL1 4DT
United
Kingdom
Goldstar France SARL
12, Rud Lech Walesa-Z.I. Pariest
77185
Lognes,
France
LG Electronics Italia S.P.A.
Centro Direzione "IL Quadrate" Via
20090
Modigliani,
Segrate (MI) Italy
LG Electronics
Espana
Adva, De Europa,
28108 Alcovendas
21
(Madrid) Spain
LG Electronics Australia
Pty Ltd.
Rydalmere NSW 2116
http://www.lge.com.au
23, pike
or
Website ;
st
http://www.lge.com
http://www.LGEservice.com
P/NO. 3828HM1029C
Printed in Korea
Download PDF