ENHANCE
D
BZ03
GCE-8481B
EnglishDeutcFraIopP
CAUTION
The laser used in the CD-R/RW drive
:
Do not
to open the
attempt
To reduce the risk of electric
No user-serviceable
Refer
damage
can
your eyes.
cover.
shock, do
parts inside.
service
servicing
to
qualified
Use of controls
or
performance
of
not
remove cover
(or back).
personnel.
procedures
other than those
specified
herein may result in hazardous radiation exposure.
WARNING
To reduce the risk of fire
:
rain
or
or
electric
shock, do
not expose this
appliance
to
moisture
Industry Canada requirement
This class B
meets all
digital apparatus
Equipment Regulations.
Cet
appareil numerique
de la classe B
requirements
respecte
of the Canadian
toutes les
Interference-Causing
du
exigences
Reglement
sur
le
materiel brouilleur du Canada.
FCC COMPLIANCE STATEMENT
Note
-
-
-
:
This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may
However, there is
no
If this
does
cause
harmful interference to radio communications.
particular installation.
reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
equipment
guarantee that interference will
cause
not
occur
harmful interference to radio
or
in
a
television
receiver is connected.
-
?
Consult the dealer
Changes
or
help.
modifications not
could void the user's
?
Authorized Service Center for
or an
FCC WARNING
This CD-R/RW Drive is for
tion instructions
expressly approved by the party responsible for compliance
to operate the equipment.
use only with UL listed personal computers that have installa-
authority
detailing
user-installation of card cage accessory.
i
This
product is manufactured to comply with the radio interference requirements
89/336/EEC, 93/68/EEC and 73/23/EEC.
of
EEC DIRECTIVE
CAUTION
-
INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM.
VARNING-OSYNLIG
LASERSTRALNING NAR
DENNA DEL
AR OPPNAD STRALEN AR
FARLIG.
This unit
CLASS 1
LASER PRODUCT
KLASSE 1
LASER PRODUKT
LUOKAN 1
LASER LAITE
KLASS 1
LASER APPARAT
CD-ROM discs with the
uses
When you use this unit as a CD
discs with the following mark
player,
following
This unit
uses
CD-R discs with the
This unit
uses
CD-RW discs with the
This unit
uses
High Speed
following
mark
This unit
uses
following
mark.
use
mark
compact
following
mark.
following
mark.
ReWritable
WARNING:
write
ReWritable
Ultra
Only
or erase
CD-RW discs with the
Speed
CD-RW discs with the
ReWritable
CD-RW drivers
Ultra
Speed
bearing
the
logo Compact Disc ReWritable Ultra Speed
HighSped
UltraSped
can
CD-RW media.
Ultra Speed CD-RW Media may be recognized by
Speed logo on the disc label or packaging material.
the
same
Compact
Attempted writes to Ultra Speed CD-RW media using CD-RW
Compact Disc ReWritable Ultra Speed may result in data loss.
ii
Disc ReWritable Ultra
drives NOT
bearing
the
logo
Contents
Introduction
Features........................................2
ImportantPrecautions.............................3
SystemEnvironment..............................4
LocationandFunctionofControls...................5
Installation
InstallingtheDrive...............................6
DeviceDrivers..................................11
Operation
HowtoUsetheDiscs............................12
Appendix
Troubleshooting.................................13
Specifications..................................14
PC DOS is
a
trademark of IBM Inc.
MS-DOS, Windows, and
Windows
95
the United States and other countries
are
by
trademarks
the Microsoft
registered in
Corporation.
The company names and product names written in this manual are
trademarks or registered trademarks of the respective companies.
Thank you for
this
purchasing
Features
CD-R/RW
?
Enhanced-IDE
Drive.
?
Power
(ATAPI)
interface.
tray loading and ejection of disc. (The disc
can
also be
ejected manually.)
?
The recorded CD-RW media
can be played in a DVD player
Player, maintaining future compatibility
multiread CD-ROM
Windows 95/98/2000/ME/XP & NT 4.0.
?
Supports
?
Automatic buffer underrun
?
48X
*
Writing speed depends on capabilities of
For Ultra speed write/rewrite, you should
Speed Writable/ReWritable discs.
max
&
technology
This drive is
error
24X
Writing (CD-R),
reading(CD-ROM)*.
CAV
or a
prevention technology-Super Link
Rewriting (CD-RW), and 48X max
max
discs.
use
media labelled Ultra
Optimum Write Speed control
with CAV
equipped
technology, so the CD-R write speed can
change in the range of 22X 48X max according to the type of the disc.
In this optimum write control system, the drive automatically selects the
best recording speed for the inserted media.
-
Package
Items
Item
-
-
-
-
-
-
-
Quantity
Internal CD-R/RW Drive
1
CD
Software
1
cable
1
Recording
E-IDE
(ATAPI)
Audio Cable
1
Screws
4
Manual for CD-R/RW Drive
1
Manual for CD
1
Mounting
Recording
Software
Important Precautions
Follow these
Precautions
?
when
handling
the drive
or
discs.
Please take notice that the manufacturer of this
offer any
or
?
precautions
warranty against data loss due
handling
or
direct
or
indirect
equipment does not
inappropriate installation
to
damages.
Please take notice that the manufacturer will bear
direct
or
indirect
damages
caused
by
the
use
no
of this
responsibility
product or its
for
responsibility
for
malfunction.
?
?
Please take notice that the manufacturer will bear
damage to data caused by this product.
Please backup (copy) all important data
no
protection against
as
data
loss.
Installation
?
Avoid
-
-
-
-
-
placing the drive
high humidity
high temperature
Don't
or
sunlight
using
the drive in
the drive
move
raise the
causing
?
Make
room
abnormal
?
?
?
subject
to:
an
a
horizontal
or
vertical
position.
angle.
suddenly
from
a
cold
place
to
a warm one
temperature suddenly. Condensation may
occur,
operation.
the disc before moving the drive.
damaged, causing data loss.
Be careful to prevent foreign objects, such as liquids or metal, from
entering the drive. In case a foreign object enters the drive, please
consult the dealer where the drive was purchased.
Don't interrupt the electric power while the drive is operating.
When connecting two IDE devices to the Primary or Secondary
connectors, make sure that the two devices are not configured as
both Master, or both Slave. If they are both set the same, Windows
may fail to run or recognize the drives.
The total length of the IDE cable should be no more than 18 inches
(about 45 cm).
sure
to
remove
The disc may be
?
location
mechanical vibration
direct
Do not install the drive at
?
a
excessive dust
We recommend
Operation
in
System Environment
Computer
This unit
can
System
requirements
be
operated
CPU
in the
system environment explained here.
350MHz
(or faster)
500MHz
or
faster
Pentium
Windows 95/98/ME
Memory
(for high speed,
recommended)
64MB
:
or
greater.
Windows NT Workstation Ver. 4.0: 64MB
greater (128MB
or
recommended)
Windows 2000/XP: 128MB or greater(256MB
over recommended)
Hard disk
650MB
or over
free space.
for
or more
(The free space needed
the quantity of data.)
Enhanced-IDE interface
Interface
Secondary
Drive
5.25-inch
bay
Master
Software
Required
on
(as Primary Slave,
Slave)
or
half-height bay required
+5V/+12V power socket
Power
writing depends
or
required
Windows 95/98/2000/ME/XP, Windows NT
OS
Workstation Ver.4.0
CD-R
CD-R, CD-RW discs
:
or
later
LG, Ricoh, Mitsubishi Chemical,
Yuden, Fuji Film, CMC, Mitsui
recommended.
(For
or
Taiyo
SKC discs
are
48X: CMC, SKC, Ritek,
Mitsubishi Chemical,
CD-RW
:
Fuji Film, Ricoh, Daxon, Mitsui)
Ricoh, Mitsubishi chemical, TDK, Fuji
Film, Sony discs
Occasionally
are
recommended.
the CD-R and CD-RW discs written
drive cannot be read
by
These unreadable discs may need to be read
drive
*
on
that did the
The disc written
using
Software
the CD-R/RW drive
might
compatible (UDF compatible)
can
2.
CD-ROM drives that
support Packet Write.
CD
the CD-R/RW
not be
readable
CD-ROM drives
CD-ROM drives that
supplied
using
compatible (UDF compatible)
1.
Install the
the CD-R/RW
original writing.
drives other than Multi-read
Multiread
by
other CD drives*.
by
CD-ROM
CD-ROM drives.
are:
read low reflectance.
Recording
Software before
using
this unit.
DirectCDTM v2.5b(s)
Introduction
Location and Function of Controls
Front Panel
6
5
12
1.
3
4
Headphone Jack
2. Volume Control
3.
Emergency Eject Hole
Stop/Eject Button
5. Disc Tray
6. Drive activity indicator (Read/Write)
4.
Rear Panel
POWER
INTERFAC E
DIGITAL
AUDIO
DG
ANALOG
AUDIO
CSM
1.
3.
+12
4
5
Digital Audio Output Connector
Analog Audio Output Connector
Jumper Connector
This
determines whether the drive is
jumper
Changing
4.
GND
2
RGL SLA
123
2.
+5
1
39
40
the master-slave
configured
configuration takes effect
as a
master
or
slave.
after power-on reset.
IDE Interface Connector
Connect to the IDE
(Integrated
Device
Electronics)
Interface
using
a
40-pin
flat IDE
cable.
NOTE
:
cause a
Do not connect
connecting
5.
5
or
short circuit and
or
disconnect the cable when the power is on,
damage
disconnecting
Power Connector
the
the cable.
system. Always
as
this could
turn the power OFF when
DirectCDTM v2.5b(s)
Installation
Installing
Before
Before
the Drive
the
installing
drive, please
You will need the
Installation
?
A
screw
note the
following points.
following:
driver of
a
suitable size to fit the
securing
computer,
find the
screws
for the drive unit.
?
The manual for the
positions
so
you
can
mounting
for the IDE controller cable.
Turn off all
peripheral appliances of the computer and the computer
itself, and disconnect their power cords from the wall sockets.
Removing the
Computer
Discharge
any static
computer
covers, etc.
Make
are
all
peripheral
off, and then
on
your person
devices of the
remove
the
NOTE
avoid
the
1.
:
There may be
2.
Remove the 51/4′′ drive
bay panel
Refer to the manual for the
cover.
inside the
computer
so
take
care
to
computer
securing
computer. Refer
to the
bay.
Do not
apply
excessive pressure to
computer.
Secure the drive with the
space behind the
from the
for details.
Insert the drive unit into the
the cables inside the
3.
the
injury.
manual for the
Drive
sharp edges
by touching
computer and the computer itself
cover.
computer for details about removing the
Cover
Mounting
sure
turned
electricity
drive,
screws
provided.
If there is not
enough
connect the IDE and other cables before
the drive.
READ
E
RTE
READ WR
I
TE
NOTE
:
This is
a
general
installation
guide.
If your PC hardware appears
different, please consult your hardware manual for installing peripheral
devices.
6
DirectCDTM v2.5b(s)
Installation
Before
Jumper Setup
installation,
set the
jumper
on
the
jumper
connector
the
on
rear
panel.
The drive
be connected
can
(up
must be set in
way.
a
unique
the Master or Slave on an EIDE (ATAPI)
four) EIDE devices are connected, each
Specific knowledge of hardware and
as
interface. When several
to
software is necessary to install the drive.
NOTE
:
If two
nected to the
may fail to
peripheral devices with the same settings are both conPrimary or to the Secondary EIDE bus, the host computer
run or
may malfunction. Careful attention is necessary.
CS: Cable Select
(CSEL)
SL: Slave
POWER
I
DIGITAL
AUDIO
ANALOG
AUDIO
CSM
SLA
1
NTERFACE
+5
GND
+12
MA: Master
2
39
40
RGL
DG
UDIO
CSM
GL
NOTE
If
more
:
Only
than
one
one
jumper
jumper
should be installed
is
39
40
SLA
on
the
jumper
connector.
installed, the drive may malfunction
or
be
damaged.
Master/Slave
setting is determined by jumper installation on the Jumper
following table shows the possible jumper settings.
Connector. The
Name
MA
Function
Drive set
as
Master
Drive set
as
Slave
C
S
M
S
L
A
(Master)
SL
(Slave)
CS
Drive mode set
(Cable Select)
host IDE interface
by
CSEL
on
the
If you use CSEL setting, the MASTER/SLAVE setting will
automatically, depending on the hardware configuration.
For details refer to the manual of your
7
computer.
be made
DirectCDTM v2.5b(s)
Installation
The CD-R/RW drive connects to the motherboard of the host
PC Connection
To Install
as a
an
IDE interface cable. You may connect the CD-R/RW Drive
Slave
or
Master
device, depending
To install the drive
Master Drive
computer
using
the
as a
on
your
Master, the jumper
as a
computer.
can
be left
from
supplied
as
factory.
Master drive
(Booting
hard
Master drive
disk)
DIGITL
AUDIO
(CD-R/RW drive)
(Jumper left as
MAster)
ANALOG
AUDIO
G
DR
GL
CSM
SLA
39
40
INTERFACE
1
2
POWER
+5 GND
+12
Motherboard
Primary
Secondary
connector
connector
-ORMaster drive
(Booting
hard
Master drive
disk)
DIGITAL
ANALOG
AUDIO
G
DR
GL
(CD-R/RW drive)
(Jumper left as
MAster)
AUDIO
CSM
SLA
39
40
INTERFACE
1
2
POWER
+5
GND +12
DIGITAL
ANLOG
AUDIO
G
DR
GL
AUDIO
CS
SL
E
1
POWER
+5 GND
2
+2
Slave drive
(Other
IDE
drive)
Secondary
Primary
connector
connector
NOTE
EIDE
:
A hard disk is
(ATAPI)
drives and CD-ROMs
8
normally
installed
interface. Other EIDE
are
then set
as
the
peripheral
differently.
Primary
Master
devices such
on
as
the
hard
DirectCDTM v2.5b(s)
To Install
Installation
To install the drive
as a
panel
Slave Drive
as a
Slave, change the jumper setting
on
the
rear
to SL.
Master drive
(Booting
DIGITAL
AUDIO
DG
hard
disk)
ANLOG
AUDIO
R
GL
CSL
E
1
2
POWER
GND +12
5
Slave drive
(CD-R/RW drive)
(Jumper set to
SLave)
-ORMaster drive
Master drive
hard
(Booting
disk)
(Other
IDE
drive)
DIGITAL
AUDIO
ANALOG
AUDIO
G
DR
GL
CSM
SLA
INTERFACE
39
0
1
POWER
+5
2
DIGITAL
AUDIO
GND
+12
Slave drive
ANALOG
AUDIO
DR
G
GL
CS
SL
E
1
POWER
+5
2
GND
(CD-R/RW drive)
(Jumper set to
SLave)
+12
Secondary
Primary
Connecting
connector
connector
Connect the power cable from the computer's power supply to the socket
the drive unit, fitting the connector firmly into the power in connector.
the Power
on
Connector
to
If there is
no
purchase
spare power cable available in the
splitter cable of a suitable type.
computer, you will have
a
POWER
+5
POWER
INTE RFACE
DIGITAL
AUDIO
DG
Beveled
NOTE
:
Improper
edge
ANALOG
AUDIO
+5
GND
GND
+12
+12
40
up
connection may
warranty. Generally, the power
9
1
2
39
CSM
RGL SLA
damage
connector
the drive and void the
can
only
fit
one
way.
DirectCDTM v2.5b(s)
Installation
Connect the
40-pin IDE cable to the back of the CD-R/RW Drive,
making sure the coloured (red) stripe on the IDE cable is connected to
pin 1 on the CD-R/RW drive. Pin 1 is closest to the Power Connector.
Connecting
the Interface
Connector
NOTE
:
Generally,
the IDE connector is
POWER
INTE RFACE
ANALOG
DIGITAL
AUDIO
AUDIO
CSM
RGL SLA
1
GND
+5
keyed
and will
only
fit
one
way.
+12
Pin1
2
39
40
DG
Red-edge
Connecting
If the
computer is using
card with
the Sound
cards
an
a
sound
card, the drive is connected
audio cable. The
or one can
be
supplied analog audio cable
purchased at a local computer store.
to the sound
fits most sound
Card
Refer to the manual for the sound card for detailed
information
regarding
connection.
DIGITAL
AUDIO
DIGITAL
AUDIO
ANALOG
AUDIO
CSM
RGL SLA
DG
ANALOG
AUDIO
RGL
INTERFACE
CSM
SLA
39
40
POWER
12
+5
GND
+12
39
40
DG
marking
L-R
LR
Sound card
Replacing the
Computer
When the installation of the drive unit is
cover
Cover
10
complete, replace
the
computer
Device Drivers
When
using
Windows 95/98/2000/ME/XP
Workstation Ver. 4.0,
or
Window NT
special device driver is required. Your system,
upon Power On and bootup after installing and connecting the new CDRW drive, will recognize and load native software drivers automatically.
no
The DOS and Windows 3.1
anytime
users can
download the DOS Device drivers
via internet.
For your
information, please consult the following
http://www.lge.com
http://www.lgeservice.com/drivers.html
For Windows
95/98/2000/ME/
In order to
?
normal drive
ensure
The drive is
displayed
Windows 95/98/ME
XP Users
Windows 2000/XP
?
operation, please
check the
[Control Panel]-[System]-[Device Manager][CD-ROM]
[Control Panel]-[System]-[Hardware]-[Device
Manager]-[DVD/CD-ROM-Drive]
:
:
displayed in
[Control Panel]-[System]-[Performance]
If the drive is not
recognized by
your
computer, please check the
items.
If
an
indicator is displayed on the IDE
Panel]-[System]-[Devices Manager]-[Hard
controller in
Disk
will need to contact your PC's manufacturer
manufacturer and
or
[Control
Controller], you
the motherboard's
get the appropriate IDE controller driver.
Run Add New Hardware in Control Panel to let PC search
new
For Windows
NT
Workstation
Ver.4.0 Users
following:
in
32-bit is
following
?
internet sites:
for
again
device.
In order to
normal drive
ensure
drive is
displayed
Adapter]-[Devices]
on
operation, please check to see if
[Control Panel]-[SCSI
the
the IDE controller in
If the drive is not
recognized by
displayed on the
[Devices], you will
IDE controller in
your
computer,
an
need to contact your PC's manufacturer
board's manufacturer and
indicator is
[Control Panel]-[SCSI Adapter]or
the mother-
get the appropriate IDE controller driver.
DirectCDTM v2.5b(s)
Operation
How to Use the Discs
When
CD-ROM
using
discs, CD-R discs
or
only
read and write errors, but data
causes
due to
labels to the discs.
or
any stickers
damage
may be
DO NOT
use
discs, don't attach
on
the disc may be lost
a
high speed!
warped discs. The
very
or
drive's
optical
non-standard discs. NON-standard discs may not
unit
play
or
properly.
Non-standard discs
are
type discs. This includes
discs
at
operate
damaged, cracked
damaged if they break.
use
store data
CD-RW
discs with them attached not
to the disc itself.
The Discs in this unit
DO NOT
Using
any discs that are not the standard 12 cm CD
8 cm discs, Sony WalkmanTM discs, non-circular
including promotional,
business card
discs, and other unusual
discs.
Emergency
This drive has
essary in
Eject
an
NOTE: Don't
1)
2)
feature that allows the CD to be
use
this feature
Turn the power to OFF.
Poke a fine-tipped object
clip)
3)
a
emergency, such
except
(such
in
an
or a
power
if
nec-
outage.
emergency.
straightened heavy duty paper
eject button. The front door will
as a
pop open and the disk tray will come partway out.
Pull the front door to open it all the way, then grip the disc tray
between thumb and forefinger and gently pull it straight out.
Using
12
ejected manually
failure of the drive
into the small hole above the
NOTE: This feature is
*
as
it
excessively
a
will
last
measure
cause
to be used
only
in
an
emergency.
malfunction.
If you cannot get a good grip on the disc tray with your
steel binder clip or spring clamp to pull it out.
fingers,
use a
Troubleshooting
Before
Before
?
Requesting
Service
?
calling
for
service, check this list.
The drive doesn't have power.
?
Is the power
?
Is the Power Connector to the drive
The
?
?
?
supply
system doesn't
cable from the host
computer plugged in?
securely
attached?
start.
Are the
Primary and Secondary connections
Slave settings correct?
Is the total length of the IDE cable 18 inches
Is each connector completely attached?
and the Master and
or
less?
Movement of the PC may loosen connections.
?
Cannot Read
?
or
Write Discs.
Is the condition of
and
others)
as
everything
it should be?
?
Does the CD-R
?
Did
or
else in the system (CPU, hard disc,
(See system environment, page 4.)
CD-RW disc have dirt
a screen saver or
other
or
scratches?
application operate
while
writing
to the
disc?
?
Is there
free space
?
Does
even
?
Is the disc loaded in the drive with the read/write surface
right
enough
writing fail
direction?
using
on
the CD-R/RW disc?
the simulation test?
?
Is the drive installed in the correct orientation?
?
Was the drive
a
or
disc moved from
high temperature
sation
on
environment?
the lens in the drive
When you call for
facing
the
(label up)
a
low
temperature environment
or on
the
is
to
possibility of condensurface of the disc.)
(There
a
service, be prepared to give as much information as
possible of your system, environment, and the specific problem. (What
happened? When? How long? What was going on? Were there any
error messages displayed? etc.)
Specifications
Host Interface
E-IDE/ATAPI
Disc diameters
Supported
12cm/8cm, standard size CD's
discs
Read Function: CD-ROM, CD-ROM XA, Audio CD, Mixed
Mode
(Audio and
(Single
Data
Photo CD
and
Combined), CD-I FMV, Video CD,
Multi-Session), CD-Plus/CD-Extra,
CD-Text, CD-R, CD-RW
Write Function: CD-ROM, CD-ROM XA, Audio CD, Mixed
Mode
and Data
(Audio
Combined),
CD-I
FMV, Video CD,
CD-Plus/CD-Extra
Mounting
direction
Read/Write
Horizontal/Vertical
Write
24X PCAV, 32X PCAV,
PCAV, 48X CAV
Write (CD-RW): 4X, 10X, 12X, 16X, 24X PCAV
Speed
(CD-R): 8X, 12X, 16X,
40X
Read
Data transfer rate
(CD):
max
48X
*Sustained:
Write: CD-RW: 600 KB/s
(4X), 1500 KB/s (10X), 1800 KB/s (12X),
(16X), 3600 KB/s (24X) PCAV
CD-R: 1200 KB/s (8X), 1800 KB/s (12X),
2400 KB/s (16X), 3600 KB/s (24X),
4800 KB/s (32X), 6000 KB/s (40X) PCAV,
7200 KB/s (48X) CAV
Read: 3000 to 7200 KB/s (20 to 48X CAV)
*Burst (ATAPI):
16.67 MB/s (PIO Mode 4), 16.67 MB/s (Multi DMA Mode 2),
33.34 MB/s (Ultra DMA Mode 2)
100ms (Typical)
2400 KB/s
Average
Buffer
Access
time(Random)
2MB
Capacity
MTBF
Audio
125000 power
output level
on
hours
Line
output: 0.7 Vrms
DC 5V, DC12V
Power
(Duty cycle 10%)
at 47 kohm
5.75"x7.27"x1.63"
Dimensions(WxDxH)
Weight
Less than 2lbs
Environmental Conditions
When
(146x184.7x41.3mm)
(0.9kg)
When not
operating
operating
Temperature
:
5 °C to 45 °C
Humidity
:
10% to 80% R.H.
5% to 90% R.H.
(No condensation)
(No condensation)
The drive's appearance and
specifications
may
(No
air
change
cooling)
without
-40°Cto60°C
prior
notice.
ⓒ 2002
Copyright
Caution!
The disc rotates at
high speed in the drive unit.
Use of worn, damaged, or non-standard CD-ROM discs
can only adversely affect the drive and cause the disc to
LG Electronics U.S.A. Inc.
1000
Sylvan Ave.
Englewood Cliffs NJ
07632
U.S.A.
or
shatter
http://www.lgeus.com
or
LG Electronics Canada Inc.
Superior Blvd, Mississauga
Ontario, Canada
12,
use a damaged
extremely rare
steps which
can
be taken to
inserting
them into
1. Take
Willich, Germany
LG Electronics U. K. Ltd.
House, 264 Bath Road,
2.
Berkshire SL1 4DT
care not to use worn, cracked, damaged,
warped or poor quality CD-ROMs, as this may
cause damage to your drive.
Check the clear plastic on the center of the disc,
cracks here
Kingdom
are
the main
cause
of disc crush.
3. Do not
play CD-ROMs which are a non-standard
(I.e. non-circular)shape, such as heart shaped
discs, or discs in the shape of a business card.
Goldstar France S.A.R.L
Paris Nord II
are
an
check your discs before
Always
the drive.
United
when you
prevent it.
LG Electronics Deutschland GMBH
Slough
use.
occur
occurrence, but there
Jakob-Kaiser-Straße
LG
only
can
CD-ROM disc in the drive. It is
235
D-47877
crush while in
Disc crush
22, Avenue des
Nations-B.P.50372 VILLEPINTE
95945 ROISSY CDG CEDEXLG France
How
can
you
keep your
discs from
becoming
damaged?
LG Electronics Italia S.P.A.
Centro Direzione "IL Quadrate" Via
Modigliani,
20090
Segrate (MI) Italy
1. When not in use, remove discs from the drive.
Keep discs in the packaging supplied with them
2.
and out of direct
sunlight
and away from heat
sources.
LG Electronics
Espana
Complejo Europa Empressaries (Edif.Bruselas)
Ctra. N-VI 28230 Las Rozas Madrid Spain
LG Electronics Australia
Pty
Rydalmere NSW
http://www.lge.com.au
23, pike
or
st
Website ;
Ltd.
2116
Excessive vibration or a sudden jolt to the drive during
operation may cause a malfunction.
Avoid exposing the drive to sudden changes in
temperature as it may cause condensation to collect
inside the drive.
http://www.lge.com
http://www.LGEservice.com
P/NO. 3828HM1037A
ⓒ2002 Made by
Download PDF

advertising