LG | L1919S-SF | LG L1919S-SF Owner’s Manual

User's Guide
L1719S/L1719SP
L1919S/L1919SP
Make
sure
to read the
Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached
on
the product and
dealer when you ask for service.
give the information to your
This unit has been
engineered and manufactured to ensure your personal
safety,
improper use may result in potential eletrical shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
however
On
Use
Safety
only the
cord, make
power cord supplied with the unit. In case you use another power
that it is certified by the applicable national standards if not being
sure
provided by the supplier. If the
manufacturer
or
power cable is faulty in any way, please contact the
the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords
cords and broken
plugs. They
technician for replacement.
Do not
Open
the
may result in
are
a
dangerous. So
shock
or
are
frayed
power
fire hazard. Call your service
Display:
There
are no user
There
are
serviceable components inside.
Dangerous High Voltages inside, even when the
Contact your dealer if the display is not operating properly.
power is OFF.
To Avoid Personal
Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
To Prevent Fire
Always
or
turn the
Hazards:
display OFF if you leave the
room
for
more
than
a
short
period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts
carry hazardous voltages.
Do not add accessories that have not been designed for this
display.
lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
During
a
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not
the display where the power cord is subject to damage.
Do not
use
this
display
sink, laundry tub, in
near water
a wet
such
basement,
as near a
or near a
place
bathtub, washbowl, kitchen
swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
or strike the Active Matrix LCD with anything hard
damage the Active Matrix LCD permanently.
Do not rub
mar, or
Do not press the LCD
some
screen
with your
finger for a long
time
as
as
this may scratch,
this may
cause
afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If
possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On
Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly
screen because over-spraying may cause electrical shock.
On
on
the
display
Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On
Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
Connecting
the
Display
Before
setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand
1.
Place the monitor with its front
2.
Assemble the Stand
Make sure you
push
Body
facing
into the
downward
product
soft cloth.
on a
in the correct direction
as
shown in the
picture.
it until you hear it "click".
Stand
Body
R
A
E
R
3. Assemble the
4.
Stand Base(Front, Rear) into the Stand
Once assembled take the monitor up
carefully and
Stand
Body
Stand Base
Body
R
A
E
R
in the correct direction.
face the front side
REA
R
FRO
NT
REA
R
FRO
NT
Important
depicts the general model of connection. Your monitor may differ from
picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
This illustration
the items shown in the
A3
Connecting
the
Display
To remove the Stand:
1. Put a cushion or soft cloth on a flat surface.
2.
Place the monitor face down
the cushion or soft cloth.
on
The Head part
The Stand
base part
3.
Hold the
product
as
it follows and lift up the Stand
4. Change
your hold on the product
direction until you hear a "click."
5.
Pull out the Stand to
as
slightly.
it follows and turn the Stand Base in the
remove.
A4
arrow
the
Connecting
To
remove
Type.
1.
Display
the Stand Base:
A
Ensure there
are
2.
four latches at the
Hold the
body
of the Stand
as
it follows.
bottom of the Stand Base.
3.
Press the four latches
toward each end
4.
as
individually
shown.
5.
Pull up the body of the Stand while
the Stand Base with the other
hand.
holding
The
Base
A5
body of the Stand and the Stand
are successfully separated.
the
Connecting
To
remove
Type.
1.
Display
the Stand Base:
B
Ensure there
are
two latches at the
2.Hold the body of the
Stand
as
it follows.
bottom of the Stand Base.
3.
4.
Press the two latches
individually
toward each end
5.
Pull up the body of the Stand while
the Stand Base with the other
hand.
holding
The
as
shown
body
Stand
separated.
A6
of the Stand and the
Base
are
successfully
Connecting
the
Display
Before
setting up the monitor, ensure that the power
system, and other attached devices is turned off.
to the
monitor, the computer
Positioning your display
1. Adjust the position
Tilt
Range
:
of the
panel
in various ways for maximum comfort.
-5˚~20˚
20
Warning:
When
adjusting
the
angle
of the screen, do not
put your finger(s) in between the head of the
monitor and the stand
body.
You
can
hurt your
finger(s).
Ergonomic
It is recommended that in order to maintain
position,
an
ergonomic and comfortable viewing
degrees.
the forward tilt angle of the monitor should not exceed 5
A7
Connecting
the
Display
Using the Computer
1. Place the monitor in a convenient, well-ventilated location near your computer.
2. Connect the signal cable. When attached, tighten the thumbscrews to secure the
connection. 1
3. Connect the power cord
the
display.
into
a
proper power outlet that is
easily accessible and
close to
2
Power Cord
Cable
Signal
Varies according to model.
NOTE
This is
of the
This
a
Wall-outlet type
simplified representation
rear
rear
view.
view
2
represents a
general model; your display may
differ from the view
as
1
shown.
PC-outlet type
PC
MAC
Mac adapter
For Apple Macintosh use,
a
separate plug adapter is needed to change
the 15 pin high density (3 row) D-sub VGA connector on the supplied
cable to a 15 pin 2 row connector.
4.
Press
button
on
the side switch
panel
to turn the power
When monitor power is turned on, the 'Self
Function' is executed
on.
Image Setting
automatically.
(Only Analog Mode)
NOTE
Self Image Setting Function'?
'
connects the monitor for the first
This function
provides the
user
with
optimal display settings.When the
user
time, this function automatically adjusts the display to optimal settings for individual
input signals. If you want to adjust the monitor while in use, or wish to manually run this function once again, push
the 'AUTO/SET' button on the side panel of the monitor. Otherwise, you may execute the Factory reset' option on
the OSD adjustment menu. However, be aware that this option initializes all the menu items except 'Language'.
'
A8
Control Panel Functions
Side
Front Panel Controls
Control
Function
MENU Button
Use this button to enter
or
exit the On Screen
Display.
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message
"OSD UNLOCKED" should appear.
Buttons
Use these buttons to select
Screen
For
or
adjust functions
Display.
more
information, refer
A9
to page A16.
in the On
Control Panel Functions
Control
Function
AUTO/SET
Use this button to enter
Button
Display.
a
selection in the On Screen
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SET button before entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best
display
mode is
17 inch monitor
:
1280
x
1024
19 inch monitor
:
1280
x
1024
Power Button
Use this button to turn the
Power Indicator
This Indicator
lights
display
up green
or
on or
off.
blue when the
display
operates normally(On Mode). If the display is in Sleep
Mode
(Energy Saving),
to amber.
A10
this indicator color
changes
On Screen
Screen
Display (OSD) Control Adjustment
Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system.
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the
To make
display to
stabilize for at least 30 minutes before
adjustments
in the On Screen
Display, follow these steps:
Press the MENU Button, then the main
To
access a
becomes
control,
use
highlighted,
the
or
making image adjustments.
menu
of the OSD appears.
Buttons. When the icon you want
press the AUTO/SET Button.
Use the
Buttons to adjust the image to the desired level. Use the
/
AUTO/SET Button to select other sub-menu items.
Push the MENU Button
once to return to
the main
menu to
select another
function. Push the MENU Button twice to exit from the OSD.
A11
On Screen
The
and
Display(OSD)
Selection and
following table indicates all the
setting menus.
Main
Sub
menu
PICTURE
On Screen
Adjustment
Display control, adjustment,
Reference
menu
To
BRIGHTNESS
adjust the brightness,
contrast and gamma of the
CONTRAST
screen
GAMMA
COLOR
sRGB
To customize the color of the
PRESET 6500K
screen
9300K
RED
GREEN
BLUE
POSITION
TRACKING
HORIZONTAL
To
VERTICAL
screen
CLOCK
of the
To
improve the clarity and
stability, sharpness of the
PHASE
screen
SHARPNESS
SETUP
adjust the position
LANGUAGE
OSD
HORIZONTAL
To customize the
screen
status for a user's
operating
environment
POSITION VERTICAL
WHITE BALANCE
POWER INDICATOR
FACTORY RESET
FLATRON
F-ENGINE
MOVIE / TEXT
To select
USER
desired
or
customize
image settings
NORMAL
:
Adjustable
NOTE
The order of icons may differ
depending
on
A12
the model (A12~A16).
On Screen
Selection and
Display(OSD)
Adjustment
were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
You
Press the MENU
Menu Name
Button, then the main menu of the OSD appears.
PICTURE
Sub-menus
Icons
Button
Tip
MENU
:
:
SET
Exit
Adjust (Decrease/Increase)
:
Enter
:
Select another sub-menu
NOTE
OSD (On Screen
Display)
menu
languages
on
A13
the monitor may differ from the manual.
On Screen
Selection and
Display(OSD)
Main
menu
Sub
Adjustment
Description
menu
PICTURE
PICTURE
of the
BRIGHTNESS
To
adjust
the
CONTRAST
To
adjust
the contrast of the
GAMMA
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
brightness
screen.
screen.
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
COLOR
PRESET
COLOR
?
?
?
RED
GREEN
MENU : Exit
: Decrease
BLUE
: Increase
SET : Select another sub-menu
sRGB: Set the screen color to fit the
SRGB standard color
specification.
Slightly reddish white.
9300K: Slightly bluish white.
6500K:
Set your
own
red color levels.
Set your
own
green color levels.
Set your
own
blue color levels.
POSITION
POSITION
HORIZONTAL
To
move
image left
VERTICAL
To
move
image
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
A14
and
right.
up and down.
On Screen
Selection and
Display(OSD)
Main
menu
Sub
Adjustment
Description
menu
TRACKING
CLOCK
TRACKING
To minimize any vertical bars or stripes
visible on the screen background.
The horizontal
screen
size will also
change.
adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
PHASE
To
the image of characters.
MENU : Exit
: Decrease
: Increase
SHARPNESS To adjust the clearness of the
SET : Select another sub-menu
SETUP
LANGUAGE
To choose the
control
screen.
language in which
displayed.
the
names are
SETUP
OSD
POSITION
To
adjust position
on
the
of the OSD window
screen.
If the output of the video card is different
required specifications, the color
WHITE
BALANCE
the
level may deteriorate due to video
distortion. Using this function, the
signal
signal
SETUP
level is
adjusted
to fit into the
standard output level of the video card
in order to provide the optimal image.
Activate this function when white and
black colors
POWER
INDICATOR
MENU
:
:
SET
:
Exit
:
present in the
screen.
Use this function to set the power
indicator on the front side of the monitor
to ON
Adjust
Adjust
are
or
OFF.
If you set OFF, it will go off.
If you set ON at any time, the power
indicator will automatically be turned
Select another sub-menu
FACTORY
Restore all factory default
"LANGUAGE."
RESET
Press the
settings except
button to reset
immediately.
If this does not improve the screen image, restore the factory default settings.
If necessary, perform the white balance function again. This function will be enabled
the input signal is an analog signal.
A15
on.
only when
On Screen
Display(OSD)
The OSD
right
screen
Selection and
Adjustment
will appear when you touch the
button
on
the
side of the monitor.
Menu Name
Icons
Sub-menu Name
FLATRON F-ENGINE
Screen when
applied
Screen when not
applied
When you execute F-ENGINE, two tones will appear
on the screen as shown. The applied screen will
appear
on
the left side, whereas the
non-applied
will appear on the right side.Touch the SET
button to use the adjusted screen.
screen
Main
Sub
menu
MOVIE
TEXT
Description
menu
This feature lets you easily select the best desired
image condition optimized to the environment
(ambient illumination, image types etc).
MOVIE: For animation
TEXT: For text
USER
adjust the USER sub-menu
function,
or
movies
User
can
You
can save or
...
Press the SET Button
...
USER
...
BRIGHTNESS
in videos
images (Word processing etc.)
You
when
To
images
manually adjust brightness, ACE or RCM.
restore the adjusted value even
using a different envir
(Brightness): Adjusts screen brightness.
ACE(Adaptive Clarity Enhancer): Selects the clarity mode.
RCM(Real Color Management): Selects the color mode.
0
Not
1
Green enhance
ACE
1
RCM
applied
2
Flesh tone
3
Color Enhance
2
SAVE
Select the SAVE sub-menu using the SET button
and save the YES value using the buttons.
NORMAL This is under normal
A16
operating
conditions.
Troubleshooting
Check the
No
following before calling for service.
image
appears
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power on and the
power indicator blue or
?
Check and
properly
?
?
see
if the power cord is connected
to the power outlet.
Press the Power button.
Adjust the brightness
and the contrast.
green?
Is the power indicator
amber?
?
If the
the
display
mouse or
is in power
saving mode, try moving
pressing any key on the keyboard to
bring up the screen.
?TrytoturnonthePC.
Doyouseean"OUTOF
RANGE" message
the screen?
on
Do you see a "CHECK
SIGNAL CABLE"
message
screen?
Do you
on
see a
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
?
This message appears when the signal cable
between your PC and your display is not
connected. Check the
the
"OSD LOCKED" message
Do you see "OSD
LOCKED" when you
push
?
MENU button?
?
You
so
they
on
cable and try
again.
the screen?
the current control
cannot be
settings,
inadvertently changed.
unlock the OSD controls at any time
pushing the MENU button for several
You
by
can secure
that
signal
can
seconds: the message
"OSD UNLOCKED" will appear.
A17
Troubleshooting
Display image
Display
is incorrect
Position is
?
incorrect.
?
Press the AUTO/SET button to
automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position icon
in the on screen display.
Check Control Panel --> Display --> Settings
and see if the frequency or the resolution were
changed. If yes, readjust the video card to the
recommend resolution.
On the
screen
?
vertical
background,
bars or stripes are
visible.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
?
?
The
screen
mono or
color is
?
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon
the on screen display.
Press the AUTO/SET button to
automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
Check if the
?
signal cable
is
properly connected
screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
and
abnormal.
in
use a
the slot.
?
Set the color
setting higher than
Settings.
at Control Panel
The
screen
blinks.
?
?
Check if the
24 bits
(true color)
-
screen
is set to interlace mode and if
yes, change it to the recommend resolution.
Make sure the power voltage is high enough, It
has to be
higher than AC100-240V 50/60Hz.
A18
Troubleshooting
Have you installed the
Have you installed the
display
?
driver?
display
driver?
Be
display driver from the display
(or diskette) that comes with your
sure
to install the
driver CD
display. Or, you can also download
our web site: http://www.lge.com.
Doyouseean
"Unrecognized monitor,
Plug&Play (VESA DDC)
?
Make
sure
Plug&Play
monitor found"
message?
A19
the driver from
to check if the video card
function.
supports
Specifications
Display
17 inch
17 inches
Anti-Glare
Panel Active matrix-TFT LCD
(43.2 cm) Flat
coating
17 inches viewable
0.264
Sync Input
Horizontal
30
Vertical
56
Input
Video
Input
Freq.
Freq.
Form
15
Form
Max
DDC 2B
Power
0n Mode
Tilt
Range
Power
Input
D-Sub Connector
Analog (0.7 Vp-p/
30
:
Mode
1024
x
x
1024
75
ohm)
@75 Hz
@60 Hz
W(Typ.)
≤1W
≤1W
With Stand
Dimensions
Weight
pin
VESA 1280
Off Mode
&
(Automatic)
(Automatic)
VESA 1280
Plug&Play
Sleep
83 kHz
75 Hz
RGB
Recommend
Consumption
-
-
Separate TTL,
SOG (Sync On Green)
Signal Input
Input
Resolution
pixel pitch
mm
Without Stand
Width
36.40
cm
/ 14.33 inches
36.40
cm
/ 14.33 inches
Height
Depth
37.80
cm
/ 14.88 inches
30.80
cm
/ 12.13 inches
18.00
cm
/
7.09 inches
6.00
cm
/
Net
3.45
Tilt
-5˚~20˚
2.36 inches
kg (7.61 lbs)
AC 100-240V~50/60Hz 0.8A
Environmental
Conditions
Operating Conditions
Temperature 10˚C to 35 ˚C
10 % to 80 % non-Condensing
Humidity
Conditions
Storage
Temperature -20˚C to 60 ˚C
5 % to 90 % non-Condensing
Humidity
Stand Base
Attached(
), Detached (
O
)
Attached(
), Detached (
O
)
Signal
cable
Power cord
Wall-outlet type
or
PC-outlet type
NOTE
Information in this document is
subject to change without
A20
notice.
Specifications
Display
19 inch
19 inches
Anti-Glare
(48.19 cm) Flat
coating
Panel Active matrix-TFT LCD
19 inches viewable
0.294
Sync Input
Input
30
Vertical
56
Freq.
Freq.
Form
15
Form
Max
DDC 2B
Power
0n Mode
Range
Power
Input
D-Sub Connector
Analog (0.7 Vp-p/
33
:
Mode
1024
x
x
1024
75
ohm)
@75 Hz
@60 Hz
W(Typ.)
≤1W
≤1W
With Stand
Dimensions
Tilt
pin
VESA 1280
Off Mode
&Weight
(Automatic)
(Automatic)
VESA 1280
Plug&Play
Sleep
83 kHz
75 Hz
RGB
Recommend
Consumption
-
-
Separate TTL,
SOG (Sync On Green)
Signal Input
Input
Resolution
pixel pitch
Horizontal
Input
Video
mm
Without Stand
Width
41.80
cm
/ 16.46 inches
41.80
cm
/ 16.46 inches
Height
Depth
41.27
cm
/ 16.25 inches
34.30
cm
/ 13.50 inches
18.02
cm
/
7.09 inches
5.92
cm
/ 2.33 inches
Net
4.3
Tilt
-5˚~20˚
kg (9.47 lbs)
AC 100-240V~50/60Hz 0.8A
Environmental
Conditions
Operating Conditions
Temperature 10˚C to 35 ˚C
10 % to 80 % non-Condensing
Humidity
Conditions
Storage
Temperature -20˚C to 60 ˚C
5 % to 90 % non-Condensing
Humidity
Stand Base
Attached(
), Detached (
O
)
Attached(
), Detached (
O
)
Signal
cable
Power cord
Wall-outlet type
or
PC-outlet type
NOTE
Information in this document is
subject to change without
A21
notice.
Preset Modes
1
2
3
4
5
6
7
8
9
10
11
*12
13
VGA
VGA
VGA
VESA
VESA
VESA
MAC
VESA
VESA
MAC
VESA
VESA
VESA
(Resolution)
640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
31.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.023
68.681
61.805
63.981
79.976
70
70
60
75
60
75
75
60
75
75
65
60
75
*
Indicator
On Mode
Sleep Mode
Off Mode
Green
or
blue
Amber
Off
Recommend Mode
Installing
the Wall mount
plate
This monitor satisfies the
the
1.
interchange
Put
a
cushion
or
specifications
of the Wall mount
plate
or
device.
soft cloth
on a
flat surface.
2.
Place the monitor face down
the cushion or soft cloth.
on
The Head part
The Stand
base part
3.
Hold the
product
as
it follows and lift up the Stand
4. Change
your hold on the product
direction until you hear a "click."
5.
Pull out the Stand to
as
slightly.
it follows and turn the Stand Base in the
remove.
A23
arrow
Installing
the Wall mount
6. Installing
the wall mount
plate
plate
Wall mount
plate(Separate purchase)
stnad-type or will mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more
details, which is provided when Wall mount plate
purchased.
This is
is
Kensington Security Slot
a locking
cable that can be purchased
separately at most
Connected to
computer
A24
stores
Digitally yours
Download PDF

advertising