LG | N1642W-PF | LG N1642W-PF Owner’s Manual

Internal Use Only
Website:http://biz.LGservice.com
E-mail:http://www.LGEservice.com/techsup.html
COLOR MONITOR
SERVICE MANUAL
CHASSIS NO. : L M97A
MODEL:
(
CAUTION
N1642W (N1642W-PFT.A***AP*)
) **Same model for Service
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
SPECIFICATIONS ................................................... 2
ADJUSTMENT ...................................................... 12
PRECAUTIONS ....................................................... 3
TROUBLESHOOTING GUIDE .............................. 14
TIMING CHART ....................................................... 7
WIRING DIAGRAM ............................................... 18
DISASSEMBLY ....................................................... 8
EXPLODED VIEW...................................................19
BLOCK DIAGRAM ................................................... 9
REPLACEMENT PARTS LIST ...............................21
DESCRIPTION OF BLOCK DIAGRAM...................11
SCHEMATIC DIAGRAM ......................................... 25
SPECIFICATIONS
1. LCD CHARACTERISTICS
Type
: TFT Color LCD Module
Active Display Area : 15.6 inch diagonal
Pixel Pitch
: 0.252 (H) x 0.252 (V)
Size
: 363.8(H) x 215.9(V) x 14.3(D)
Color Depth
: 16.7M(8bit + FRC) colors
Electrical Interface
: LVDS
Surface Treatment
: Anti-Glare, Hard Coating(3H)
Operating Mode
: Transmissive mode,Normally White
Backlight Unit
: 2 CCFL
4. RESOLUTION
Max
Recommend
5. POWER SUPPLY
5-1. Power Adaptor(Built-in Power)
Input : AC 100-240V~, 50/60Hz, 0.8A
5-2. Power Consumption
MODE
2. OPTICAL CHARACTERISTICS
2-1. Viewing Angle by Contrast Ratio ≥ 10
Left : -45°(Typ)
Top : +20°(Typ)
2-2. Luminance
2-3. Contrast Ratio
less than 22 W(max)
ON/ON
ACTIVE
Right : +45°(Typ)
Bottom : +45°(Typ)
STAND BY
OFF/ON
OFF
less than 1 W
Flicker
SUSPEND
ON/OFF
OFF
less than 1 W
Flicker
: 170(Typ) (Typ. ± 30)-sRGB
: 175(min), 230(Typ)-6500K
: 110(min)-9300K
DPMS OFF
OFF/OFF
OFF
less than 1 W
Flicker
POWER S/W OFF
-
-
less than 1 W
OFF
7. DIMENSIONS (with TILT/SWIVEL)
Width
Depth
Height
Input Form
15 pin D-Sub Connector
RGB Analog
(0.7 Vp-p/ 75 ohm)
X-PORT Connector
X-PORT Signal
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
: 381.7 mm (15.03'')
: 198.4 mm (7.81'')
: 323.9 mm (12.75'')
8. WEIGHT (with TILT/SWIVEL)
3-2. Video Input Signal
• X-PORT Signal Input
BLUE
6-1. Operating Temperature : 10°C~35°C (50°F~95°F)
6-2. Relative Humidity
: 10%~80% (Non-condensing)
6-3. MTBF
: 50,000 HRS with 90%
Confidence level
Lamp Life
: 40,000 Hours (Min)
1440 x 900 (60Hz)
1280 x 1024 (60Hz)
1024 x 768 (60Hz)
1280 x 720 (60Hz)
800 x 600 (72Hz)
1360 x 768 (60Hz)
Signal Input
Input Form
less than 20 W(typ)
6. ENVIRONMENT
: 400(Min.)
DFC -> 5000 : 1(Typ)
Vertical Freq.
57 - 63 Hz (Automatic)
RGB support 60Hz only(except Dos mode)
• RGB
H/V SYNC VIDEO POWER CONSUMPTION LED COLOR
POWER ON (NORMAL)
3. SIGNAL (Refer to the Timing Chart)
3-1. Sync Signal
• RGB
Horizontal Freq.: 30 - 66 kHz (Automatic)
• X-PORT
VESA 1360 x 768 @60 Hz
VESA 1360 x 768 @60 Hz
-2-
Net. Weight
Gross Weight
: 2.6 kg (5.78 lbs)
: 3.6 kg (8. 0 lbs)
LGE Internal Use Only
PRECAUTION
WARNING FOR THE SAFETY-RELATED COMPONENT.
WARNING
• There are some special components used in LCD
monitor that are important for safety. These parts are
marked on the schematic diagram and the
replacement parts list. It is essential that these critical
parts should be replaced with the manufacturer’s
specified parts to prevent electric shock, fire or other
hazard.
• Do not modify original design without obtaining written
permission from manufacturer or you will void the
original parts and labor guarantee.
BE CAREFUL ELECTRIC SHOCK !
• If you want to replace with the new backlight (CCFL) or
inverter circuit, must disconnect the AC adapter
because high voltage appears at inverter circuit about
650Vrms.
• Handle with care wires or connectors of the inverter
circuit. If the wires are pressed cause short and may
burn or take fire.
Leakage Current Hot Check Circuit
AC Volt-meter
TAKE CARE DURING HANDLING THE LCD MODULE
WITH BACKLIGHT UNIT.
• Must mount the module using mounting holes arranged
in four corners.
• Do not press on the panel, edge of the frame strongly
or electric shock as this will result in damage to the
screen.
• Do not scratch or press on the panel with any sharp
objects, such as pencil or pen as this may result in
damage to the panel.
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
To Instrument's
exposed
METALLIC PARTS
1.5 Kohm/10W
• Protect the module from the ESD as it may damage the
electronic circuit (C-MOS).
• Make certain that treatment person’s body are
grounded through wrist band.
• Do not leave the module in high temperature and in
areas of high humidity for a long time.
• The module not be exposed to the direct sunlight.
• Avoid contact with water as it may a short circuit within
the module.
• If the surface of panel become dirty, please wipe it off
with a softmaterial. (Cleaning with a dirty or rough cloth
may damage the panel.)
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-3-
LGE Internal Use Only
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this
service manual and its supplements and addenda, read
and follow the SAFETY PRECAUTIONS on page 3 of this
publication.
NOTE: If unforeseen circumstances create conflict
between the following servicing precautions and any of the
safety precautions on page 3 of this publication, always
follow the safety precautions. Remember: Safety First.
General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC
power source before;
a. Removing or reinstalling any component, circuit
board module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical
plug or other electrical connection.
c. Connecting a test substitute in parallel with an
electrolytic capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect
polarity installation of electrolytic capacitors may
result in an explosion hazard.
d. Discharging the picture tube anode.
2. Test high voltage only by measuring it with an
appropriate high voltage meter or other voltage
measuring device (DVM, FETVOM, etc) equipped with
a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
3. Discharge the picture tube anode only by (a) first
connecting one end of an insulated clip lead to the
degaussing or kine aquadag grounding system shield
at the point where the picture tube socket ground lead
is connected, and then (b) touch the other end of the
insulated clip lead to the picture tube anode button,
using an insulating handle to avoid personal contact
with high voltage.
4. Do not spray chemicals on or near this receiver or any
of its assemblies.
5. Unless specified otherwise in this service manual,
clean electrical contacts only by applying the following
mixture to the contacts with a pipe cleaner, cottontipped stick or comparable non-abrasive applicator;
10% (by volume) Acetone and 90% (by volume)
isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual,
lubrication of contacts in not required.
6. Do not defeat any plug/socket B+ voltage interlocks
with which receivers covered by this service manual
might be equipped.
7. Do not apply AC power to this instrument and/or any of
its electrical assemblies unless all solid-state device
heat sinks are correctly installed.
8. Always connect the test receiver ground lead to the
receiver chassis ground before connecting the test
receiver positive lead.
Always remove the test receiver ground lead last.
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
9. Use with this receiver only the test fixtures specified in
this service manual.
CAUTION: Do not connect the test fixture ground strap
to any heat sink in this receiver.
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid-state) devices can be
damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive (ES)
Devices. Examples of typical ES devices are integrated
circuits and some field-effect transistors and
semiconductor "chip" components. The following
techniques should be used to help reduce the incidence of
component damage caused by static by static electricity.
1. Immediately before handling any semiconductor
component or semiconductor-equipped assembly, drain
off any electrostatic charge on your body by touching a
known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device,
which should be removed to prevent potential shock
reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with
ES devices, place the assembly on a conductive
surface such as aluminum foil, to prevent electrostatic
charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or
unsolder ES devices.
4. Use only an anti-static type solder removal device.
Some solder removal devices not classified as "antistatic" can generate electrical charges sufficient to
damage ES devices.
5. Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage ES
devices.
6. Do not remove a replacement ES device from its
protective package until immediately before you are
ready to install it. (Most replacement ES devices are
packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable
conductive material).
7. Immediately before removing the protective material
from the leads of a replacement ES device, touch the
protective material to the chassis or circuit assembly
into which the device will be installed.
CAUTION: Be sure no power is applied to the chassis
or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged
replacement ES devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or
the lifting of your foot from a carpeted floor can
generate static electricity sufficient to damage an ES
device.)
-4-
LGE Internal Use Only
General Soldering Guidelines
1. Use a grounded-tip, low-wattage soldering iron and
appropriate tip size and shape that will maintain tip
temperature within the range or 500。F to 600。F.
2. Use an appropriate gauge of RMA resin-core solder
composed of 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean and well tinned.
4. Thoroughly clean the surfaces to be soldered. Use a
mall wire-bristle (0.5 inch, or 1.25cm) brush with a
metal handle.
Do not use freon-propelled spray-on cleaners.
5. Use the following unsoldering technique
a. Allow the soldering iron tip to reach normal
temperature.
(500。F to 600。F)
b. Heat the component lead until the solder melts.
c. Quickly draw the melted solder with an anti-static,
suction-type solder removal device or with solder
braid.
CAUTION: Work quickly to avoid overheating the
circuitboard printed foil.
6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal
temperature (500。F to 600。F)
b. First, hold the soldering iron tip and solder the strand
against the component lead until the solder melts.
c. Quickly move the soldering iron tip to the junction of
the component lead and the printed circuit foil, and
hold it there only until the solder flows onto and
around both the component lead and the foil.
CAUTION: Work quickly to avoid overheating the
circuit board printed foil.
d. Closely inspect the solder area and remove any
excess or splashed solder with a small wire-bristle
brush.
IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong)
through which the IC leads are inserted and then bent flat
against the circuit foil. When holes are the slotted type,
the following technique should be used to remove and
replace the IC. When working with boards using the
familiar round hole, use the standard technique as
outlined in paragraphs 5 and 6 above.
Removal
1. Desolder and straighten each IC lead in one operation
by gently prying up on the lead with the soldering iron
tip as the solder melts.
2. Draw away the melted solder with an anti-static
suction-type solder removal device (or with solder
braid) before removing the IC.
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad
and solder it.
3. Clean the soldered areas with a small wire-bristle
brush. (It is not necessary to reapply acrylic coating to
the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1. Remove the defective transistor by clipping its leads as
close as possible to the component body.
2. Bend into a "U" shape the end of each of three leads
remaining on the circuit board.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the
corresponding leads extending from the circuit board
and crimp the "U" with long nose pliers to insure metal
to metal contact then solder each connection.
Power Output, Transistor Device
Removal/Replacement
1. Heat and remove all solder from around the transistor
leads.
2. Remove the heat sink mounting screw (if so equipped).
3. Carefully remove the transistor from the heat sink of the
circuit board.
4. Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6. Replace heat sink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close
as possible to diode body.
2. Bend the two remaining leads perpendicular y to the
circuit board.
3. Observing diode polarity, wrap each lead of the new
diode around the corresponding lead on the circuit
board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder
joints of the two "original" leads. If they are not shiny,
reheat them and if necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board
hollow stake.
2. Securely crimp the leads of replacement component
around notch at stake top.
3. Solder the connections.
CAUTION: Maintain original spacing between the
replaced component and adjacent components and the
circuit board to prevent excessive component
temperatures.
-5-
LGE Internal Use Only
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed
circuit board will weaken the adhesive that bonds the foil
to the circuit board causing the foil to separate from or
"lift-off" the board. The following guidelines and
procedures should be followed whenever this condition is
encountered.
At IC Connections
To repair a defective copper pattern at IC connections use
the following procedure to install a jumper wire on the
copper pattern side of the circuit board. (Use this
technique only on IC connections).
1. Carefully remove the damaged copper pattern with a
sharp knife. (Remove only as much copper as
absolutely necessary).
2. carefully scratch away the solder resist and acrylic
coating (if used) from the end of the remaining copper
pattern.
3. Bend a small "U" in one end of a small gauge jumper
wire and carefully crimp it around the IC pin. Solder the
IC connection.
4. Route the jumper wire along the path of the out-away
copper pattern and let it overlap the previously scraped
end of the good copper pattern. Solder the overlapped
area and clip off any excess jumper wire.
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
At Other Connections
Use the following technique to repair the defective copper
pattern at connections other than IC Pins. This technique
involves the installation of a jumper wire on the
component side of the circuit board.
1. Remove the defective copper pattern with a sharp
knife.
Remove at least 1/4 inch of copper, to ensure that a
hazardous condition will not exist if the jumper wire
opens.
2. Trace along the copper pattern from both sides of the
pattern break and locate the nearest component that is
directly connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead
of the nearest component on one side of the pattern
break to the lead of the nearest component on the
other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is
dressed so the it does not touch components or sharp
edges.
-6-
LGE Internal Use Only
TIMING CHART
VIDEO
A
E
D
SYNC
B
C
MODE
H/V
Sync
Polarity
1
H(Pixels)
-
2
V(Lines)
H(Pixels)
+
-
V(Lines)
-
3
H(Pixels)
V(Lines)
+
+
4
H(Pixels)
V(Lines)
-
5
H(Pixels)
+
V(Lines)
+
31.468
Total
Period
(E)
900
Video
Active
Time ( A )
720
Sync
Duration
(D)
18
70.08
31.469
449
800
400
640
12
16
2
96
35
48
59.94
525
480
10
2
33
40.0
37.879
60.317
1056
628
800
600
40
1
128
4
88
23
800 x 600
65.0
48.363
60.0
1344
806
1024
768
24
3
136
6
160
29
1024 x 768
47.712
1792
1360
64
256
60.015
795
768
3
112
6
Dot
Clock
28.321
25.175
85.5
Frequency
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-7-
Front
Porch
(C)
108
Blanking
Time
(B)
54
18
Resolution
720 X 400
640 x 480
1360 x 768
LGE Internal Use Only
DISASSEMBLY
#1
#2
Pull the cabinet upwards,
Then push the button ”push” to separate
the hinge body and stand body.
Pull the cabinet upwards,
Then separate all latches on each side.
#4
#3
Disassemble the back cover.
Remove the control button from cabinet,
Then disassemble the connector.
#6
#5
Turn around the base lock to open the
lock between base cover and stand body..
Separate the lamp shield from rear shield.
Please pull off the latch first.
#7
Then separate stand body and base cover.
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-8LGE Internal Use Only
Copyright 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 9-
P300_6p
5VN
RJ-45
P201
P200
Key1/Key2
LED_AM/BL
5V
Sync
H/V
R/G/B
R/G/B/H/V
3.3V
EPM3064
CPLD
IC201
3.3V
IC202
SW IC
ST_DET
D-SDA/D-SCL
PS2
K/B
JK201
JK200
5V
Audio
AMP Block
5V
L/R
Audio
5V
P202
P205
JK300
6.8 ohm
L
Speaker
R
Speaker
P302_4p
CSZ/SDO/SCK/SDI
WP_FLH
IC103
EEPROM
3.3V
1.8 V
3.3V
IC102
Flash ROM
3.3 V
IC204
1.8V Reg
IC203
3.3V Reg
WP
SCLK/SDATA
5V
L/R SPK-
5V
L/R SPK+
Earphone
HP
DET
APA2068
Amp IC
IC300
Mute
1.8V
3.3V
Volume
MODON
5V
SW
IC100
Scaler
TSUM16WAL
(FE211M-LF)
PS2
Mouse
L/R
Audio
Input SW
R/G/B/H/V
Key1/Key2
Lamp_ADJ
Lamp_ADJ
LED_AM/BL
Dim_ADJ
Inv_On
Dim_ADJ
Inv_On
5V
T-con : 1CH
T-con : 2CH
LVDS
RGB
D-sub
P204_11p
BLOCK DIAGRAM
LGE Internal Use Only
DESCRIPTION OF BLOCK DIAGRAM
1. Video Controller Part.
This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the
digital video signal using a pixel clock.
The pixel clock for each mode is generated by the PLL.
The range of the pixel clock is from 25MHz to 136MHz in N1642W case(28MHz to 146MHz In N1642W CASE).
This part consists of the Scaler, ADC convertor, TMDS receiver and LVDS transmitter.
The Scaler gets the video signal converted analog to digital,interpolates input to 1360 x 768 resolution signal
and outputs 8-bit R, G, B signal to transmitter.
2. Power Part.
This part consists of the one 3.3V, and one 1.8V regulators to convert power which is provided 5V in Power board.
18V is provided for inverter, 5V is provided for LCD panel and micom in N1642W case .
Also, 5V is converted 3.3V and 1.8V by regulator. Converted power is provided for IC in the main board.
The inverter converts from DC18V to AC 700Vrms and operates back-light lamps of module in N1642W case.
3. MICOM Part.
This part is include video controller part. And this part consists of EEPROM IC which stores control data, Reset IC and
the Micom.
The Micom distinguishes polarity and frequency of the H/V sync are supplied from signal cable.
The controlled data of each modes is stored in EEPROM.
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 10 -
LGE Internal Use Only
LIPS Board Block Diagram
18V
50 ~ 60Hz
EMI
COMPONENTS
INPUT RECTIFIER
AND FILTER
HVDC
ENERGY
TRANSFER
67KHz
OUTPUT RECTIFIER
AND FILTER
5V
GND
LINE
100 ~ 240V
PHOTOCOUPLER
ISOLATION
PWM
CONTROL
CIRCUIT
PRIMARY
SIGNAL
CollectionION
SECONDARY
Operation description_Power
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC,VCCI CISPR, the
circuit included a line-filter, across line capacitor and of course the primary protection fuse.
2. Input rectifier and filter.
This part function is for transfer the input AC voltage to a DC voltage through a bridge rectifier and a bulk capacitor.
3. Energy Transfer.
This part function is for transfer the primary energy to secondary through a power transformer.
4. Output rectifier and filter.
This part function is to make a pulse width modulation control and to provide the driver signal to power switch, to
adjust the duty cycle during different AC input and output loading condition to achieve the dc output stabilized, and
also the over power protection is also monitor by this part.
5. Photo-Coupler isolation.
This part function is to feed back the DC output changing status through a photo transistor to primary controller to
achieve the stabilized DC output voltage.
6. Signal collection.
This part function is to collect the any change from the DC output and feed back to the primary through photo
transistor.
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 11 -
LGE Internal Use Only
ADJUSTMENT
Windows EDID V1.0 User Manual
Operating System: MS Windows 98, 2000, XP
Port Setup: Windows 98 => Doesn’t need setup
Windows 2000, XP => Need to Port Setup.
This program is available for LCD Monitor only.
2. EDID Read & Write
1) Run WinEDID.exe
1. Port Setup
a) Copy “UserPort.sys” file to
“c:\WINNT\system32\drivers” folder
b) Run Userport.exe
2) Edit Week of Manufacture, Year of Manufacture,
Serial Number
a) Input User Info Data
b) Click “Update” button
c) Click “ Write” button
c) Remove all default number
d) Add 300-3FF
e) Click Start button.
f) Click Exit button.
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 12 -
LGE Internal Use Only
SERVICE OSD
1) Turn off the power switch at the right side of the display.
2) Wait for about 5 seconds and press MENU, POWER switch for 1 second interval.
3) The SVC OSD menu contains additional menus that the User OSD menu as described below.
a) CLEAR ETI : To initialize using time.
c) Auto Color : W/B balance and Automatically sets the gain and offset value.
(press key for over 3 sec)
d) AGING : Select Aging mode(on/off).
b) Module : To select applied module.
d) NVRAM INIT : EEPROM initialize.(24C08, press key for over 3 sec)
e) R/G/B-9300K : Allows you to set the R/G/B-9300K value manually.
f) R/G/B-6500K : Allows you to set the R/G/B-6500K value manually.
g) R/G/B-Offset : Allows you to set the R/G/B-Offset value manually.(Analog Only)
h) R/G/B-Gain : Allows you to set the R/G/B-Gain value manually.(Analog Only)
A
IBM
Compatible PC
Video Signal
Generator
9
15
10
5
1
C
d
se
RS
23
2C
tu
13
1
25
5V
LL
EL
No
6
5
PARALLEL PORT
PA
RA
Control Line
C
11
6
1
OFF
14
ON
F
Power inlet (required)
5V
4.7K
4.7K
220
WE
R
VG
TO
R
YN
NI
ON
E
5V
4.7K
OFF
74LS06
V-S
MO
CS
T
PO
S
A
Power Select Switch
(110V/220V)
Power LED
74LS06
B
E ST Switch
B
F V-Sync On/Off Switch
(Switch must be ON.)
Figure 1. Cable Connection
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 13 -
LGE Internal Use Only
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
Check P204Voltage
Pin5, Pin6 (5V)?
NO
Check Power Board,
And Find Out a Short Point
as Opening
Each Power Line
YES
Check
IC203 Pin2 Voltage
(3.3V) ?
NO
Check 3.3V Line
(Open Check)
No Problem
YES
Check Key Control
Connector Routine
Is IC100
Pin75 (3.3V)
Voltage ?
NO
Check 3.3V Line
YES
1
Check IC100 Pin 96
Pulse
NO
Check X-TAL
YES
Check IC100
Waveforms
1
IC100-#96
Copyright 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 14 -
LGE Internal Use Only
2. NO RASTER (OSD IS NOT DISPLAYED) – LIPS
NO RASTER
(OSD IS NOT DISPLAYED)
P204
PIN5, PIN6
5V?
NO
CHECK POWER BOARD,
AND FIND OUT A SHORT
POINT AS OPENING EACH
POWER LINE
YES
P204 PIN9
5V?
NO
CHECK MICOM INV
ON/OFF PORT.
YES
P204 PIN10
5V?
NO
YES
CHECK
PULSE AS
CONTACTING SCOPE
PROBE TO CAUTION LABEL.
(CONTACT PROBE TO
CAUTION LABEL.
CAN YOU SEE PULSE
AT YOUR
SCOPE?
NO
1. CONFIRM BRIGHTNESS
OSD CONTRL STATE.
2. CHECK MICOM DIM-ADJ
PORT
LIPS
YES
REPLACE CCFL LAMP
IN THE LCD MODULE
Copyright 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 15 -
LGE Internal Use Only
3. NO RASTER (OSD IS NOT DISPLAYED) – MSTAR
NO RASTER
(OSD IS NOT DISPLAYED)
IC100
PIN 16, 75
3.3V?
NO
CHECK IC203
YES
IC100
PIN96, 97
OSCILLATE AS
14.31MHZ?
1
NO
1. CHECK C509, C510
SOLDERING CONDITION
2. CHECK X501
3. TROUBLE IN IC100
YES
2
IC100
PIN27 IS 48KHz H-SYNC?
PIN28 IS 60Hz V-SYNC?
IS PULSE APPEARED
AT SIGNAL PINS?
AT MODE 12?
NO
CHECK CONNECTION
LINE FROM D-SUB TO
IC100
YES
TROUBLE IN CABLE
OR LCD MODULE
Waveforms
1
IC100-#96, 97
2
2 IC100-#28 V-SYNC
IC100-#27 H-SYNC
Copyright 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 16 -
LGE Internal Use Only
4. TROUBLE IN DPM
TROUBLE IN DPM
3
NO
CHECK
R221, R222
CHECK PC
PC IS NOT GOING
INTO DPM OFF MODE
YES
CHECK
IC100 PIN 27,28
SYNC PULSE ?
NO
CHECK H/V SYNC LINE
YES
TROUBLE IN U501
Waveforms
3
R221 H-Syn
3
R222V-Sync
Copyright 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 17 -
LGE Internal Use Only
WIRING DIAGRAM
30P
EAD57188308
11P
EAD42157801
6P
6631900030L
Copyright
2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 18 -
LGE Internal Use Only
320
300
310
060
020
070
080
410
420
- 19 -
920
400
910
430
440
EXPLODED VIEW
EXPLODED VIEW PARTS LIST
* Note: Safety mark
Ref. No.
Description
Part No.
300
ABJ36436113
Cabinet Assembly,W1642 ... 16" -
310
MEY40926601
Knob, MOLD ABS HF-350 MAIN 5 key WX42 BLACK
320
MBG41956001
Button,Power, MOLD ABS WX42 translucent ABS power button + lens
400
ACQ73457501
Cover Assembly,Rear, W1642 ... 16" -
410
MDQ61864902
Frame, PRESS EGI 0.8 L177WSB EGI L177W Rear Frame LPL-HSD local
420
MDQ61865001
Plate,Shield, PRESS SPTE 0.3 LAMP SPTE -
430
MCK40926801
Cover, MOLD ABS HF-350 W1642 ABS Hinge body
440
MCK40927901
Cover, MOLD ABS HF-350 W1642 ABS HINGE COVER
910
MCK62135301
Cover, MOLD ABS W1642 ABS -
920
AAN35581001
Cover, MOLD ABS HF-350 W1642 ABS Base cover
020
EAJ42583301
LCD,Module-TFT, M156B1-L01 WXGA 15.6INCH 1366X768 250CD COLOR 65% 16/9 500:1 CMO15.6"W,TN,ZBD,Non-Glare,2CCFL,16.7M,Response time:8ms,Viewing Angle:90/45 CHI MEI OPT
060
EBR41617001
PCB Assembly, CONTROL T.T LM73A BAIKAL 3 19-INCH RD -
070
EBU50480810
BAIKAL 4 MSTAR ANALOG BRAND LM97A
080
EAY56379402
DPS-25EP B FREE N1642W LCD DELTA ELECTRONICS - DELTA ELECTRONICS INTERNATIONAL LIMITED-MACAO COMMERCIAL
120
6410TMW004A
Power Cord, UC,LP-45 & H05VV-F 0.75_3C, LS-60_1.87M_BLK LP-45 LS-60 1.87M - 250V 10A H05VV-F 3X0.75MM2 BLACK INMETRO N LONGWELL COMPANY
6410TMW002B
Power Cord, SP-305+IS-14 H05VV-F 3GX0.75mm2 CT-12_1.87M_BLK SP-305 IS-14 1.87M NONE 250V 15A H05VV-F 3X0.75MM2 BLACK INMETRO N I-SHENG ELECTRIC WIRE & CABLE CO.,
- 20 -
SCHEMATIC DIAGRAM
1. SCALER
Copyright 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-21-
LGE Internal Use Only
2. INTERFACE
Copyright 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 22-
LGE Internal Use Only
SC101:1
1/2PC201:2
PS2561BL1-1-V-A(G)
T 3.15A H 250V 10 L
F101
TH101
C107
ZD105
ZD104
BZX79-B11,133
LFV-DP8252
LF102:2
C106
1nF 50V K
R106
24K 1/4W J
R110
0 1/8W J
CX101
330nF 300VAC
806K 1/4W F
R103
806K 1/4W F
R101
R102
806K 1/4W F
HFH-CE7299
LF101:1
U101
FSDM0465RSWDTU
CY103
100pF 250VAC
3.3nF 250VAC
CY101
C104
100nF 50V K
CY102
100pF 250VAC
BD101
D2SB60-7000
47nF 500V K
C109
C105
47uF 25V M
47nF 500V K
C108
C101
68uF 450V M
ZD103
HZ24-2 TA-E
TRGP10D
D102
R105
24K 1/4W J
R104
24K 1/4W J
D101
C102
1nF 1KV K
TRGP10M-B5
1 1/4W J
R108
1 1/4W J
R109
R107
100K 1W J
SRW24LQ-T24H016-1
T101:4
R251
51 1W J
BYQ28E-200
D251
C251
680pF 200V K
C252
1nF 50V K
C207
10uF 50V M
SBT150-06JS
D253
300 1/8W J
R259
R255
51 1W J
PS2561BL1-1-V-A(G)
1/2 PC201:1
AS431BZTR-E1
U201
R260
4.7K 1/8W J
470uF 25V M
C253
5V
8.2K 1/8W J
R272
C264
1000uF 10V M
C262
10nF 50V K
TZX18C-TAP
ZD254
C263
CB-4.0-15
L254
R270
5.11K 1/4W F
R256
1K 1/8W J
+5.1V
R273
4.87K 1/8W F
R258
100K 1/8W J
C260
1000uF 10V M
R257
1K 2W J
18V
+5.1V
C265
220uF 10V M
Q251
MMBT4401LT1G
C261
470uF 25V M
18V
+5.1V
ON/OFF
BRIG-DC
BRIG-PWM
P201
R313
10K 1/8W F
18V
BRIG-PWM
R315
100K 1/8W F
C301
1uF 25V K
E-0437A
FB303
Q310
2N7002A-RTK/P
R317
10K 1/8W F
C303
470uF 25V M
9.53K 1/8W F
R319
C326
R304
287K 1/8W F
REF
698 1/8W F
R310
A
FAN7314AMX
U301
OLR
C324
FB
220pF 50V J
C316
100K 1/8W J
R301
10K 1/8W J
R302
10nF 50V K
C306
1M 1/8W F
R309
C308
1uF 25V K
C307
C317
33nF 50V K
C319
C325
1nF 50V J COG
R306
4.75K 1/8W F
220nF 50V K
C310
B
80.6K 1/8W F
R314
C304
ON/OFF
R305
66.5K 1/8W F
C313
BRIG-DC
1N4148TA
D314
+18V
REF
R316
R307
5.1K 1/8W F
C315
C312
1uF 25V K
R323
332K 1/8W F
R321
10K 1/8W J
RT
R318
24.9K 1/8W F
C314
220pF 50V F
90.9K 1/8W F
R308
Q303
C321
330nF 25V K
C311
10nF 50V K
2N7002A-RTK/P
C320
1uF 25V K
RT
R328
R320
10 1/8W J
REF
1.21M 1/8W F
R322
10 1/8W J
R354
D303
BAV70,235
D310
1N4148TA
D311
1N4148TA
Q305
AP4511GH
4.7uF 25V K
C329
4.7uF 25V K
C327
C318
2.2nF 50V K
C323
OP1
OP2
C322
C439
4.7nF 50V K
C438
5pF 6KV D
IH-DP8009
T301:7
10K 1/8W J
R327
10K 1/8W J
R325
C328
2.2nF 50V K
C433
5pF 6KV D
C430
4.7nF 50V K
C441
C429
5pF 6KV D
C431
1nF 1KV K
C432
OLR
OP1
OP2
R440
1K 1/8W F
R433
1K 1/8W F
1N4148TA
D401
D402
1N4148TA
1nF 1KV K
C440
R446
1K 1/8W F
R432
1K 1/8W F
1K 1/8W F
R431
D412
BAV99,235
1K 1/8W F
R441
D409
BAV99,235
P401:4
FB
P402:4
FB
P/NO : MFL59082025
Mar . 2009
Printed in China
Download PDF

advertising