LG | N195WU | LG N195WU-PN Owner’s Manual

ENGLISH
OWNER'S MANUAL
NETWORK MONITOR
Please read the safety information carefully before using the product.
Network Monitor Model
N195WU
N225WU
www.lg.com
2
Table of Contents
ENGLISH
ENG
TABLE OF CONTENTS
3
ASSEMBLING AND
PREPARING
25 TROUBLESHOOTING
3
Unpacking
4
Parts and buttons
27 PRODUCT SPECIFICATION
7
Lifting and moving the Monitor set
7
Setting Up the Monitor set
7
- Attaching the Stand Base
8
- Detaching the stand base
8
- Adjusting the stand body
9
- Adjusting the angle
9
- Mounting on a table
10
- Using the Kensington locking device
11
- Detaching the stand body
11
- Installing the wall mount plate
12
- Mounting on a wall
13 USING THE MONITOR SET
13
Using Primary Station
13
- D-SUB IN connection - PC
14
Using Standard Stations
14
- USB cable connection - PC
14
- USB cable connection to Daisy Chain
15
- Peripheral device connection
15
- Self Image Adjustment
16 CUSTOMIZING SETTINGS
16
Accessing The Main Menus
17
MENU Settings
17
- Picture
18
- Color
19
- Display
20
- Volume
21
- Others
22
SMART+ Settings
(Only N195WU model)
22
- Auto Bright
23
- Original Ratio
24
AUTO Settings : D-SUB Input
29
Preset Mode
29
Power Indicator
29
29
30 PROPER POSTURE
30
Proper posture for using the monitor
ASSEMBLING AND PREPARING
Unpacking
Please check whether all the components are included in the box before using the product. If there are
missing components, contact the retail store where you purchased the product. Note that the product and
components may look different from those shown here.
User Manual/
Software Installation CD/
Card
Power Cord
Stand Base
15-pin D-SUB Signal Cable
AC/DC adaptor
A-B Type USB Cable
CAUTION
Only use an approved LG power adapter.
yy
Damage caused by other power adapters is not covered by warranty.
yy
NOTE
Note that the components may look different from those shown here.
yy
Without prior notice, all information and specifications in this manual are subject to change to improve
yy
the performance of the product.
To purchase optional accessories, visit an electronics store or online shopping site or contact the retail
yy
store where you purchased the product.
ENG
ENGLISH
ASSEMBLING AND PREPARING
3
4
ASSEMBLING AND PREPARING
Parts and buttons
ENGLISH
ENG
N195WU
Power Indicator
yyLED On : Power is on
yyLED Off: Power is off
(Power Button)
Input Connectors
(See p.15)
Front Buttons
Input Connectors (See p.13 to 14)
NOTE
Keep radio away 10 cm from the front side buttons and power button.
yy
ASSEMBLING AND PREPARING
5
ENG
ENGLISH
N225WU
Power Indicator
yyLED On : Power is on
yyLED Off: Power is off
(Power Button)
Input Connectors
(See p.15)
Front Buttons
Input Connectors (See p.13 to 14)
NOTE
Keep radio away 10 cm from the front side buttons and power button.
yy
6
ASSEMBLING AND PREPARING
Button
ENGLISH
ENG
MENU
Description
Activates the main menu.
OSD Lock/Unlock
Functions
Locks/unlocks the OSD screen.
yy To lock the OSD screen, press and hold the MENU button
for several seconds. The "OSD LOCKED" message will be
displayed and the screen will be locked.
yy To unlock the OSD screen, press and hold the MENU
button again for several seconds. The "OSD UNLOCKED"
message will be displayed and the screen will be unlocked.
SMART+
Use this button to enter AUTO BRIGHT(Only N195WU model), ORIGINAL RATIO
menus.
AUTO
To adjust the monitor settings, press the AUTO button on the MONITOR SETUP OSD
menu (only supported for analog signal(D-SUB)).
For optimal screen display, use the following resolution.
Optimal Resolution
N195WU
1366 x 768
N225WU
1920 x 1080
INPUT
Allows selection of the input signal.
yy If you connect the monitor to a computer using a D-SUB cable, select either the USB
or D-SUB input signal.
yy If only one computer is connected to the monitor, the input signal is detected automatically. The initial input signal is USB.
EXIT
Exits the OSD menu.
(Power Button)
D-SUB input
yy Use this button to switch the monitor on or off.
USB input
yy On : Press the power button to turn on the power.
yy Monitor Off : If you press the power button, the monitor will automatically turn off after
5 seconds.
yy USB Off : Press the power button twice to turn off the USB power.
Power Indicator
N195WU
When the monitor is in operating mode, the power indicator
will turn purple (on mode).
When the monitor is in power saving mode, the power indicator will blink purple.
N225WU
When the monitor is in operating mode, the power indicator
will turn blue (on mode).
When the monitor is in power saving mode, the power indicator will blink blue.
ASSEMBLING AND PREPARING
When moving or lifting the Monitor set, read the
following to prevent the Monitor set from being
scratched or damaged and for safe transportation
regardless of its type and size.
CAUTION
Avoid touching the screen at all times, as this
yy
may result in damage to the screen or some
of the pixels used to create images.
Setting Up the Monitor set
Attaching the Stand Base
1 Place the monitor's screen face down.
CAUTION
To protect the screen from scratches, cover
yy
the surface with a soft cloth.
2 Check the position (at the front and rear) of
the stand body, then mount the stand base on
the stand body as shown in the figure.
It is recommended to move the Monitor set in
yy
the box or packing material that the Monitor
set originally came in.
Before moving or lifting the Monitor set,
yy
disconnect the power cord and all cables.
Hold the top and bottom of the Monitor
yy
set frame firmly. Make sure not to hold the
transparent part, speaker, or speaker grill
area.
Stand Body
Stand Base
3 Using a coin, turn the screw clockwise to seWhen holding the Monitor set, the screen
yy
should face away from you to prevent the
screen from scratches.
When transporting the Monitor set, do not
yy
expose the Monitor set to jolts or excessive
vibration.
When transporting the Monitor set, keep the
yy
Monitor set upright, never turn the Monitor
set on its side, or tilt towards the left or right.
cure the stand base.
Stand Body
Stand Base
ENG
ENGLISH
Lifting and moving the
Monitor set
7
8
ASSEMBLING AND PREPARING
ENGLISH
ENG
Detaching the stand base
Adjusting the stand body
1 Place the monitor's screen face down.
1 Place the monitor's screen face down.
To protect the screen from scratches, cover the
surface with a soft cloth.
2 Using a coin, turn the screw in the stand base
counterclockwise. Detach the stand base from
the stand body.
Stand Body
Stand Base
CAUTION
The components appearing in the illustrayy
tions may look different from the actual product.
Do not carry the monitor upside-down as this
yy
may cause it to fall off its stand, resulting in
damage or injury.
To avoid damaging the screen when lifting
yy
or moving the monitor, only hold the stand or
the plastic cover. This avoids putting unnecessary pressure on the screen.
To protect the screen from scratches, cover the
surface with a soft cloth.
2 Press the button as shown and pull the stand
body up.
ASSEMBLING AND PREPARING
Mounting on a table
1 Place the monitor mounted on the stand base
1 Lift the monitor and place it on the table in an
in an upright position.
2 Adjust the angle of the screen. The angle of the
upright position.
Install at least 10 cm away from the wall to
ensure sufficient ventilation.
screen can be adjusted up to 15° forwards and
5° backwards for a comfortable viewing experience.
10 cm
-5
15
10 cm
10 cm
10 cm
Front Side
Rear Side
WARNING
To avoid injury to the fingers when adjusting
yy
the screen, do not hold the lower part of the
monitor's frame as illustrated below.
-5
15 to touch or press the screen
Be careful
not
yy
area when adjusting the angle of the monitor.
2 Connect the adaptor to the monitor, then plug
the power cord into the wall outlet.
3 Press the
(Power) button on the front of the
monitor to turn on the monitor.
CAUTION
Unplug the power cord prior to moving or
yy
installing the monitor. There is risk of electric
shock.
When you connect the DC jack to the moniyy
tor, ensure it is inserted tightly to prevent it
from coming loose.
ENG
ENGLISH
Adjusting the angle
9
10
ASSEMBLING AND PREPARING
ENGLISH
ENG
Using the Kensington locking
device
The connector for the Kensington lock is located
on the rear of the monitor.
For more information on installation and usage,
refer to the Kensington lock user manual or visit
the website at http://www.kensington.com.
Connect the monitor to the table with the Kensington lock cable.
NOTE
Using the Kensington lock is optional. The
yy
accessories can be purchased at your local
electronics store.
ASSEMBLING AND PREPARING
11
Installing the wall mount plate
1 Place the monitor's screen face down. To
This monitor has a VESA compatible mount on the
back. Most mounts will require an LG mounting
plate.
2 Using a screwdriver, Remove the Cover and
1 Place the monitor's screen face down. To
protect the screen from scratches, cover the
surface with a soft cloth.
detach from the monitor.
protect the screen from scratches, cover the
surface with a soft cloth.
2 Place the wall mount plate on the monitor and
align it with the screw holes on the monitor.
3 Using a screwdriver, tighten the four screws to
fix the plate onto the monitor.
3 Using a screwdriver, remove the five screws
and detach the stand from the monitor.
Wall Mount Plate
NOTE
The wall mount plate is sold separately.
yy
For more information on the installation, refer
yy
to the wall mount plate's installation guide.
ENG
ENGLISH
Detaching the stand body
12
ASSEMBLING AND PREPARING
ENGLISH
ENG
Mounting on a wall
Model
Install the monitor at least 10 cm away from the
wall and leave about 10 cm of space at each side
of the monitor to ensure sufficient ventilation. Detailed installation instructions can be obtained from
your local retail store. Please refer to the manual
to install and set up a tilting wall mounting bracket.
VESA (A x B)
Stand Screw
Required Screw
Wall Mount Plate
(Optional)
N195WU
N225WU
75 x 75
M4
4
RW120
10 cm
VESA (A x B)
yy
10 cm
10 cm
B
A
10 cm
If you intend to mount the Monitor set to a wall,
attach Wall mounting interface (optional parts) to
the back of the set.
When you install the Monitor set using the wall
mounting interface (optional parts), attach it
carefully so it will not drop.
1 Please, Use the screw and wall mount interface
CAUTION
Unplug the power cord before moving or inyy
stalling the monitor to avoid electric shocks.
in accordance with VESA Standards.
2 If you use screw longer than standard, the
monitor might be damaged internally.
3 If you use improper screw, the product might be
damaged and drop from mounted position. In
this case, LG Electronics is not responsible for it.
4 VESA compatible.
5 Please use VESA standard as below.
784.8 mm (30.9 inch) and under
yy
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm
787.4 mm (31.0 inch) and above
yy
* Please use VESA standard wall mount pad
and screws.
NOTE
The wall mount kit includes the installation
yy
guide and necessary parts.
The wall mounting bracket is optional. The
yy
accessories can be purchased at your local
retail store.
The length of the screw may differ for each
yy
wall mounting bracket. Ensure the correct
length of the screw is used.
yyFor more information, please refer to the user
manual for the wall mounting bracket.
USING THE MONITOR SET
13
Using Primary Station
CAUTION
This monitor supports the *Plug and Play
yy
feature.
*Plug and Play: A feature that allows you to
add a device to your computer, without having
to reconfigure anything or install any manual
drivers.
D-SUB IN connection - PC
D-SUB IN transfers analog video signals from the
PC to the monitor.
Connect the monitor to the PC using the provided
15-pin D-SUB signal cable as illustrated below.
Connect the input signal
yy
cable and tighten in the
direction of the arrow. To
prevent disconnection
secure the cable tightly.
Do not press on the screen for a prolonged
yy
time. This may cause image distortion.
Do not display a still image on the screen
yy
for a prolonged time. This may cause image
retention. If possible, use the screen saver.
NOTE
Back of the product.
To connect the monitor to a computer, use
yy
the appropriate signal cable (D-SUB).
A converter can be used to convert the DVI-I
yy
input signal to D-SUB input signal.
When connecting the power cord to the outyy
let, use a grounded (3-hole) multi-socket or a
grounded wall outlet.
The monitor may flicker when turned on in an
yy
area of low temperature. This is normal.
Sometimes red, green or blue spots may apyy
pear on the screen. This is normal.
RGB OUT
PC
CAUTION
The D-SUB OUT port is used to output the
yy
image signals inputted from the USB port.
The D-SUB OUT port is not supported if the
D-SUB IN port is being used.
HURB
ENG
ENGLISH
USING THE MONITOR SET
14
USING THE MONITOR SET
Using Standard Stations
ENGLISH
ENG
USB cable connection - PC
D-SUB IN transfers analog video signals from the
PC to the monitor.
Connect the monitor to the PC using the provided
15-pin D-SUB signal cable as illustrated below.
USB cable connection to Daisy
Chain
D-SUB IN transfers analog video signals from the
PC to the monitor.
Connect the monitor to the PC using the provided
15-pin D-SUB signal cable as illustrated below.
Back of the product.
Back of the product.
Back of the product.
NOTE
If the USB cable provided is not long enough,
yy
you may need to purchase an additional
extension cable. (maximum length 5 m)
NOTE
Up to 2 monitors can be connected by daisyyy
chaining, as shown above.
When using a daisy chain, connect the
yy
mouse to the USB port on the left at the back
of the monitor.
USING THE MONITOR SET
Peripheral device connection
Right
NOTE
Peripheral devices are sold separately.
yy
The USB ports on the bottom of the moniyy
tor can be used to connect the keyboard,
mouse, and other USB devices. But, USB
ports on the right of the monitor can't be used
to connect the keyboard.
Headphones, speakers or microphone may
yy
not work normally, depending on the server
PC settings.
Virtual solutions may affect the functions or
yy
speed of the specific USB storage device.
Self Image Adjustment
Bottom
Press the power button on the front to turn on
the monitor. When powered on, the "Self Image
Adjustment" function will run automatically (only
available for analog [D-SUB input] signals).
N195WU
N225WU
CAUTION
If a PS2 keyboard and mouse are connected
yy
to the PC audio device in a multi-computing
environment (normal mode), the sound
output will be supported through the analog
port. If a USB keyboard and mouse are connected, the sound output will be supported
through the USB headphones. If using a PC
without a PS2 keyboard/mouse input port,
please use a USB audio (headphones) for
sound output.
NOTE
What is "Self Image Adjustment"? This funcyy
tion runs when the monitor is connected for
the first time and performs automatic image
adjustment for each signal (only available for
analog [D-SUB input] signals) to provide an
optimal screen display.
ENG
ENGLISH
Connect peripheral devices to the monitor using
USB, headphone, speaker, and microphone ports.
15
16
CUSTOMIZING SETTINGS
ENGLISH
ENG
CUSTOMIZING SETTINGS
Accessing The Main Menus
1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu.
2 Press to select the desired menu item.
3 To change the settings of the selected item press the buttons on the front of the monitor.
To return to the upper menu or set other menu items, use the up arrow (
) button.
4 Select EXIT to leave the OSD menu.
N195WU
N225WU
Front Side Buttons
AUTO (See p.24)
Optimizes the resolution.
/ Disconnects from the server.
MENU (See p.17)
Sets the screen options.
EXIT (See p.6)
Exits the OSD menu.
MONITOR SETUP
MENU
SMART+ (See p.22)
Sets the Auto Bright (Only N195WU
model) ,Original Ratio.
SMART+ VOLUME
AUTO
VOLUME (See p.20)
Sets the volume.
INPUT
EXIT
INPUT (See p.6)
Sets the external input.
NOTE
Different menu items are enabled depending on the type of input signal.
D-SUB Input: MENU, SMART+, AUTO, INPUT, EXIT
yy
USB Input: MENU, SMART+, VOLUME, INPUT, EXIT
yy
The language of the monitor's OSD menu and that of the OSD menu illustrated in the CD-ROM
yy
manual may be different.
CUSTOMIZING SETTINGS
17
MENU Settings
MENU
ENG
ENGLISH
Picture
PICTURE
1 Press any button on the front of the monitor to
display the MONITOR SETUP OSD menu.
2 Press the MENU button to display the options
in the OSD menu.
3 Set the options by pressing the buttons on the
BRIGHTNESS
CONTRAST
SHARPNESS
front of the monitor.
4 Select EXIT to leave the OSD menu.
EXIT
To return to the upper menu or set other menu
items, use the up arrow (
) button.
Each option is explained below.
Analog
(D-SUB)
USB
BRIGHTNESS
o
o
Sets the brightness of the screen.
CONTRAST
o
o
Sets the contrast of the screen.
SHARPNESS
o
o
Sets the sharpness of the screen.
Menu
Description
yyAnalog: D-SUB (analog signal) input.
USB: Internal signal through the USB.
NOTE
If the screen is not displayed properly after adjusting the settings, use the "FACTORY RESET" opyy
tion to revert back to the factory default settings. If necessary, enable the "WHITE BALANCE" option
again. This option is enabled only for analog (D-SUB) signals.
18
CUSTOMIZING SETTINGS
Color
ENGLISH
ENG
MENU
COLOR
1 Press any button on the front of the monitor to
display the MONITOR SETUP OSD menu.
2 Press the MENU button to display the options
in the OSD menu.
3 Set the options by pressing the buttons on the
front of the monitor.
COLOR TEMP
PRESET
RED
GREEN
BLUE
GAMMA
PRESET
WARM
GAMMA 1
4 Select EXIT to leave the OSD menu.
EXIT
To return to the upper menu or set other menu
items, use the up arrow (
) button.
Each option is explained below.
Menu
COLOR TEMP
Analog
(D-SUB)
USB
o
o
PRESET
o
USER
GAMMA
o
Description
Allows PRESET or USER to be selected.
WARM
Sets the screen color to a reddish tone.
MEDIUM
Sets the screen color between the reddish and bluish
tone.
COOL
Sets the screen color to a bluish tone.
o
o
You can customize the picture color using Red, Green, and Blue
colors.
o
o
Sets the clarity of the screen.
The gamma value can be set to 0, 1 or 2, from darker to brighter
screen colors respectively.
yyAnalog: D-SUB (analog signal) input.
USB: Internal signal through the USB.
CUSTOMIZING SETTINGS
Display
MENU
19
DISPLAY
ENG
ENGLISH
1 Press any button on the front of the monitor to
display the MONITOR SETUP OSD menu.
2 Press the MENU button to display the options
in the OSD menu.
3 Set the options by pressing the buttons on the
HORIZONTAL
VERTICAL
CLOCK
PHASE
front of the monitor.
4 Select EXIT to leave the OSD menu.
EXIT
To return to the upper menu or set other menu
items, use the up arrow (
) button.
Each option is explained below.
Analog
(D-SUB)
USB
HORIZONTAL
o
x
Moves the display area left or right.
VERTICAL
o
x
Moves the display area up or down.
o
x
If vertical lines are shown on the screen, adjust the frequency to minimize the lines and adjust the screen's horizontal width.
o
x
Adjusts the focus of the screen's image.
Use when frequencies are shown on the screen or when the text appears overlapped. For optimal results, use this option after adjusting
the "CLOCK" option.
Menu
CLOCK
PHASE
Description
yyAnalog: D-SUB (analog signal) input.
USB: Internal signal through the USB.
20
CUSTOMIZING SETTINGS
Volume
MENU
VOLUME
ENGLISH
ENG
1 Press any button on the front of the monitor to
display the MONITOR SETUP OSD menu.
2 Press the MENU button to display the options
in the OSD menu.
3 Set the options by pressing the buttons on the
front of the monitor.
4 Select EXIT to leave the OSD menu.
EXIT
To return to the upper menu or set other menu
items, use the up arrow (
) button.
Each option is explained below.
Menu
VOLUME
Analog
(D-SUB)
USB
x
o
Description
To adjust the volume of headphone/Speaker.
(Only for USB input)
yyAnalog: D-SUB (analog signal) input.
USB: Internal signal through the USB.
CUSTOMIZING SETTINGS
Others
MENU
21
OTHERS
ENG
ENGLISH
1 Press any button on the front of the monitor to
display the MONITOR SETUP OSD menu.
2 Press the MENU button to display the options
in the OSD menu.
3 Set the options by pressing the buttons on the
front of the monitor.
LANGUAGE
POWER OFF OSD
POWER INDICATOR
BUTTON INDICATOR
WHITE BALANCE
FACTORY RESET
English
ON
ON
ON
NO
NO
4 Select EXIT to leave the OSD menu.
EXIT
To return to the upper menu or set other menu
items, use the up arrow (
) button.
Each option is explained below.
Menu
LANGUAGE
Analog
(D-SUB)
USB
o
o
Sets the menu screen to the desired language.
o
Enables or disables the power off message when turning power off.
If it is set to "Off", the power off message is not displayed while
maintaining client connection.
If it is set to "On", the power off message is displayed. (See p.6)
o
Use this function to set the power indicator on the front side of the
monitor to ON or OFF.
If you set OFF, it will be turned off.
If you set ON at any time, the power indicator will automatically be
turned on.
o
Use this function to set the control key indicator on the front side of
the monitor to ON or OFF.
If you set OFF, it will be turned off.
If you set ON, it will be turned on.
o
x
If the video card output is different from the specified level, the color
may appear to have altered due to the video signal distortion. The
white balance adjusts the output signal level to correspond to that of
the standard signal, thus providing optimal display. Run this option
when the screen displays an image with both white and black.
o
o
Resets the screen to the factory default settings. Note that the language option will not be reset.
POWER OFF OSD
x
POWER
INDICATOR
BUTTON
INDICATOR
o
o
WHITE BALANCE
FACTORY RESET
Description
yyAnalog: D-SUB (analog signal) input.
USB: Internal signal through the USB.
NOTE
When connecting monitors in a daisy chain, select "Off" for the "Power Off OSD" option.
yy
22
CUSTOMIZING SETTINGS
SMART+ Settings
ENGLISH
ENG
Auto Bright
(Only N195WU model)
SMART+
AUTO BRIGHT
1 Press any button on the front of the monitor to
display the MONITOR SETUP OSD menu.
ON
2 Press the SMART+ button to display the op-
OFF
tions in the OSD menu.
EXIT
3 Set the options by pressing the buttons on the
front of the monitor.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu
items, use the up arrow (
) button. Each option is explained below.
Menu
ON
OFF
Analog
(D-SUB)
USB
o
o
If select on,it automatically controls the brightness of display to best
suit the surrounding working environment,providing the optimal
viewing condition and maximized user convenience.
o
o
If select off,auto brightness is off.
Description
yyAnalog: D-SUB (analog signal) input.
USB: Internal signal through the USB.
CUSTOMIZING SETTINGS
Original Ratio
SMART+
23
ORIGINAL RATIO
ENG
ENGLISH
1 Press any button on the front of the monitor to
display the MONITOR SETUP OSD menu.
2 Press the SMART+ button to display the options in the OSD menu.
WIDE
ORIGINAL
3 Set the options by pressing the buttons on the
front of the monitor.
EXIT
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu
items, use the up arrow (
) button. Each option is explained below.
Menu
WIDE
ORIGINAL
Analog
(D-SUB)
USB
o
o
Switch to full screen mode according to input image signal.
o
o
Change the input image signal ratio to original.
This function works only if input resolution is lower than Monitor set
ratio (16:9).
Description
yyAnalog: D-SUB (analog signal) input.
USB: Internal signal through the USB.
24
CUSTOMIZING SETTINGS
AUTO Settings : D-SUB Input
ENGLISH
ENG
1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu.
2 Press the AUTO button to automatically adjust the
screen.
3 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items,
use the up arrow (
N195WU
PROCESSING AUTO IMAGE ADJUSTMENT
FOR OPTIMAL DISPLAY
CHANGE RESOLUTION TO 1366 x 768
) button.
N225WU
PROCESSING AUTO IMAGE ADJUSTMENT
FOR OPTIMAL DISPLAY
CHANGE RESOLUTION TO 1920 x 1080
Pressing the AUTO button allows the monitor to automatically optimize the screen to the current display
mode.
If you are not satisfied with the optimized screen, you can manually adjust the position of the display area,
frequency, phase and sharpness in the OSD menu.
(Only available for D-SUB [analog] signals. Note that the sharpness setting is only available for digital signals.)
NOTE
What is "Auto Image Adjustment"? The Auto Image Adjustment option allows you to improve the picyy
ture quality if the screen is dimmed, if the text appears blurred or spread, if the screen flickers or if the
display area is not centered after adjusting the resolution. (Only available for D-SUB [analog] signals.)
Troubleshooting
25
Nothing is displayed on the screen
Is the monitor's power cord
yy Check if the power cord is correctly plugged in to the outlet.
plugged in?
Is the power indicator on?
yy Check the power indicator.
Is the power indicator displaying yy Adjust the brightness and the contrast.
as purple?
Is the power indicator blinking? yy If the monitor is in power saving mode, move the mouse or press any
key on the keyboard to switch the display on.
yy Check if the computer is turned on.
Is the "OUT OF RANGE" mes- yy This occurs when signals transferred from the PC (video card) are out
sage displayed?
of the horizontal or vertical frequency range of the monitor. Please see
the "Product Specification" section of this manual to set the appropriate frequency.
Is the "CHECK SIGNAL CAyy This is displayed when the signal cable between the PC and the moniBLE" message is displayed?
tor is missing or disconnected. Check the cable and reconnect.
The "OSD LOCKED" message is displayed.
Is the "OSD LOCKED" mesyy The OSD lock feature is enabled to prevent undesired modification
sage displayed when the MENU
of the OSD settings. Press and hold the MENU button for a couple of
button is pressed?
seconds to unlock the OSD. (The "OSD UNLOCKED" message will be
displayed.)
The screen retains an image.
Does image sticking occur even yy Displaying a still image for a prolonged time may cause damage to the
when the monitor is turned off?
screen, resulting in the retention of the image.
yy Use a screen saver to protect the screen when using the monitor for a
prolonged period of time.
NOTE
Vertical Frequency: In order to display an image, the screen must be refreshed dozens of times per
yy
second like a fluorescent lamp. The number of times the screen is refreshed per second is called
vertical frequency or refresh rate and is represented by Hz.
Horizontal Frequency: The time it takes to display one horizontal line is called the horizontal cycle.
yy
The number of horizontal lines displayed in one second can be calculated by dividing one by the horizontal cycle. This is called horizontal frequency and is represented by kHz.
ENG
ENGLISH
TROUBLESHOOTING
26
Troubleshooting
ENGLISH
ENG
The image is displayed abnormally.
Does the display area appear
Pressing the AUTO button will automatically optimize the screen to the
uncentered?
current display mode.
If you are not satisfied with the optimized screen, you can manually
adjust the POSITION option in the OSD menu.
Does the screen exhibit vertical Pressing the AUTO button will automatically optimize the screen to the
lines?
current display mode.
If you are not satisfied with the optimized screen, you can manually
adjust the FREQUENCY option in the OSD menu.
Does the screen display horiPressing the AUTO button will automatically optimize the screen to the
zontal frequencies, or does the current display mode.
text appear blurred?
If you are not satisfied with the optimized screen, you can manually
adjust the PHASE option in the OSD menu.
NOTE
Check if the video card's resolution or frequency is within the range allowed by the monitor and set to
yy
the recommended (optimal) resolution in Control Panel > Display > Settings.
Failing to set the video card to the recommended (optimal) resolution may result in blurred text, a
yy
dimmed screen, a truncated display area or misalignment of the display.
The configuration procedure may differ depending on your computer and/or operating system. Also,
yy
some video cards may not support certain resolutions. If this is the case, contact the computer or
video card manufacturer for assistance.
The AUTO option is only available for D-SUB (analog) signals.
yy
The recommended monitor resolution (optimized resolution) of the WMS 2011 operating system is
yy
usually 1364 x 768, but the actual monitor resolution is 1366 x 768. This is not a monitor malfunction;
it occurs due to the characteristics of the operating system. (Only N195WU model)
The display color is abnormal.
Does the display color appear
yy Set the color to 24 bit (true color) or higher. In Windows, go to Control
discolored (16 color)?
Panel > Display > Settings > Color Quality.
Does the display color appear
yy Check if the signal cable is connected properly. Re-connect the cable
unstable or in monochrome?
or re-insert the PC's video card.
Are there spots on the screen? yy When using the monitor, pixilated spots (red, green, blue, white or
black) may appear on the screen. This is normal for the LCD screen.
It is not an error nor is it related to the monitor's performance.
Product Specification
N195WU
LCD Screen
Type
Resolution
Pixel Pitch
Maximum Resolution
Video Signal
Input Connector
Power
AC/DC Adapter
Dimension
Weight (Without
Packaging)
Stand Angle
Adjustment
Environment
Condition
470.1 mm (18.51 inch) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Screen
Diagonal length of the screen: 470.1 mm
0.30 mm x 0.30 mm
1366 x 768 @ 60 Hz
Recommended Resolution 1366 x 768 @ 60 Hz
Horizontal Frequency
30 kHz to 66 kHz
Vertical Frequency
57 Hz to 63 Hz
Synchronization
Separate Sync / USB
15-pin D-SUB (Analog), USB
19 V
1.7 A
Power Consumption
On Mode: 22 W (Typical)
Power Saving Mode ≤ 1 W / 7 W
Off Mode ≤ 1 W
Manufacturer : LITE-ON, Model PA-1650-68
Input: AC 100-240 V
Output: DC 19 V
Monitor Size (Width x Height x Depth)
457.9 mm x 369.5 mm x 197.9 mm
2.6 kg
Forwards/Backwards: -5° to 15°
Operating Condition
Storing Condition
Temperature: 10°C to 35°C;
Humidity: 10% to 80%
Temperature: -20°C to 60°C;
Humidity: 5% to 90%
The specifications are subject to change without notice.
ENG
ENGLISH
PRODUCT SPECIFICATION
27
28
Specifications
ENGLISH
ENG
N225WU
LCD Screen
Type
Resolution
Pixel Pitch
Maximum Resolution
Video Signal
Input Connector
Power
AC/DC Adapter
Dimension
Weight (Without
Packaging)
Stand Angle
Adjustment
Environment
Condition
546.8 mm (21.53 inch) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Screen
Diagonal length of the screen: 546.8 mm
0.248 mm x 0.248 mm
1920 x 1080 @ 60 Hz
Recommended Resolution 1920 x 1080 @ 60 Hz
Horizontal Frequency
30 kHz to 68 kHz
Vertical Frequency
57 Hz to 63 Hz
Synchronization
Separate Sync / USB
15-pin D-SUB (Analog), USB
19 V
1.7 A
Power Consumption
On Mode: 28 W (Typical)
Power Saving Mode ≤ 1 W / 7 W
Off Mode ≤ 1 W
Manufacturer : LITE-ON, Model PA-1650-68
Input: AC 100-240 V
Output: DC 19 V
Monitor Size (Width x Height x Depth)
524.6 mm x 406.9 mm x 198 mm
3.1 kg
Forwards/Backwards: -5° to 15°
Operating Condition
Storing Condition
Temperature: 10°C to 35°C;
Humidity: 10% to 80%
Temperature: -20°C to 60°C;
Humidity: 5% to 90%
The specifications are subject to change without notice.
Product Specification
29
Preset Mode
ENG
ENGLISH
N195WU
Preset Mode
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Polarity (H/V)
720 x 400
31.468
70
-/+
640 x 480
31.469
60
-/-
800 x 600
37.879
60
+/+
1024 x 768
48.363
60
-/-
1360 x 768
47.712
60
+/+
1366 x 768
47.712
60
+/+
Preset Mode
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Polarity (H/V)
720 x 400
31.468
70
-/+
640 x 480
31.469
60
-/-
800 x 600
37.879
60
+/+
1024 x 768
48.363
60
-/-
1360 x 768
47.712
60
+/+
1366 x 768
47.712
60
+/+
1680 x 1050
64.674
60
-/-
1680 x 1050
65.290
60
-/+
1920 x 1080
67.500
60
+/+
Remark
N225WU
Power Indicator
N195WU
Mode
LED Color
On Mode
Purple
Power Saving
Flashing Purple
Off Mode
Off
N225WU
Mode
LED Color
On Mode
Blue
Power Saving
Flashing Blue
Off Mode
Off
Remark
30
Proper Posture
ENGLISH
ENG
PROPER POSTURE
Proper posture for using the monitor
Adjust the angle so that the screen is slightly lower than your eyes.
Using the monitor for a prolonged period of time can cause eye fatigue. Take a 10-minute break every
yy
hour.
The stand is designed to best support the monitor when the optimal conditions are selected.
yy
Adjust the angle of the monitor from -5° to 15° to obtain the best view of the screen.
You should be
looking
slightly down at
the screen.
Adjust the angle
from -5° to 15°
so that there is no reflection
or glare from the
screen.
Place your hands gently on the keyboard,
keeping your arms bent
at the elbows
and extended horizontally in front of you.
Make sure to read the Safety Precautions
before using the product.
Keep the Owner's Manual(CD) in an
accessible place for future reference.
The model and serial number of the SET
is located on the back and one side of the
SET. Record it below should you ever need
service.
MODEL
SERIAL
ENERGY STAR is a set of power-saving
guidelines issued by the U.S. Environmental
Protection Agency(EPA).
As an ENERGY STAR Partner LGE U. S. A.,Inc. has
determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
Download PDF

advertising