LG | N2200P | LG N2200P Owner’s Manual

Precautions
Important
This unit has been
engineered and manufactured to ensure your personal
safety, however improper use may result in potential electrical shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this monitor, observe the following basic rules for its
installation, use, and servicing.
On
Use
Safety
only the
cord, make
power cord supplied with the unit. In case you use another power
that it is certified by the applicable national standards if not being
sure
provided by the supplier. If the
manufacturer
or
power cable is faulty in any way, please contact the
the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
a power source indicated in the specifications of
the monitor. If you are not sure what type of power supply
you have in your home, consult with your dealer.
the monitor
Operate
this manual
or
listed
only from
on
Overloaded AC outlets and extension cords
cords and broken
plugs. They
technician for replacement.
Do not
Open
There
may result in
are
a
dangerous. So are frayed
shock
or
power
fire hazard. Call your service
the Monitor.
are no user
serviceable components inside.
Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the monitor is not operating properly.
There
are
To Avoid Personal
Injury :
place the monitor on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
Do not try to roll a stand with small casters across thresholds or deep pile
Do not
carpets.
To Prevent Fire
Always
or
Hazards:
turn the monitor OFF if you leave the room for more than a short
period
of time. Never leave the monitor ON when leaving the house.
Keep children from dropping or pushing objects into the monitor's cabinet
openings. Some internal parts
carry hazardous voltages.
Do not add accessories that have not been designed for this monitor.
During
lightning storm or when the monitor is to be left unattended for an
period of time, unplug it from the wall outlet.
bring magnetic devices such as magnets or motors near the picture
a
extended
Do not
tube.
A1
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not
the monitor where the power cord is subject to damage.
Do not
use
this monitor
sink, laundry tub, in
near water
such
basement,
as near a
place
bathtub, washbowl, kitchen
swimming pool.
Monitors are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
a wet
or near a
failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the monitor on a bed, sofa, rug,
can cause
etc.
Place the monitor in
a
built-in enclosure unless proper ventilation is
Cover the openings with cloth or other material.
Place the monitor near or over a radiator or heat
On
provided.
source.
Cleaning
Unplug the monitor before cleaning the face of the monitor screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the
monitor
On
screen
because overspray may
cause
electrical shock.
Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
Connecting
the Monitor
Before
setting up the monitor, ensure that the power is turned off to the
monitor, computer system, and other attached devices.
Carefully set the monitor face-down with the underside facing you.
Connecting the Tilt/Swivel
1. Align the hooks on the tilt/swivel
stand
stand with the
matching slots
in the base of
the monitor.
2.
3.
Insert the hooks into slots.
Slide the tilt/swivel stand toward the front of the monitor until the latches click
into the locked position.
NOTE
This illustration depicts the general model of connection. Your monitor may differ from the
items shown in the picture.
Slot
Hook
Latch
AA3
Hook
Connecting
the Monitor
Using the Computer
1. Connect the signal cable. When mated, tighten the thumbscrews to secure the
connection.
2. Connect the power cord into a properly power outlet that is easily accessible and
close to the monitor.
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your monitor
may differ from the view as shown.
Signal Cable
Power Cord
Attached Type*
Wall-outlet
type*
Detached Type*
*
PC-outlet
Varies according to model.
type*
PC
MAC
Mac adapter
For Apple Macintosh use,
a separate plug adapter is needed to
change the 15 pin high density (3 row) D-sub VGA connector
on the supplied cable to a 15 pin 2 row connector.
A4
Control Panel Functions
Front Panel Controls
Control
Function
Power Button
Use this button to turn the monitor
Power
This Indicator
(DPMS)
Indicator
lights
on or
off.
up green when the monitor
operates normally. If the monitor is in DPM
(Energy Saving) mode, this indicator color changes
to amber.
MENU
(or OSD)
Button
Use this button to enter
Use these buttons to choose
the
Button
on screen
display.
Buttons
SELECT
exit the
or
(or SET)
on screen
Use this button to enter
screen
display.
A5
or
adjust
items in
display.
a
selection in the
on
Control Panel Functions
Control
Direct Access Function
Button
Bring
up Contrast
Button
Bring
up
The Contrast and
in the On Screen
Button
SHARPNESS
Brightness adjustment
Brightness functions are
Display (OSD) menu.
Brings
also available
up the clearness of the
letters, pictures
AUTO
adjustment
or
image
moving pictures.
:
For
seeing
letters
For
seeing pictures or the photographs
For
seeing moving pictures
adjustment function
When
adjusting your display settings, always press the AUTO
entering the On Screen Display(OSD). This will
automatically adjust your display image to the ideal settings for
the current screen resolution size (display mode).
button before
The best
display
mode is 1600
x
1200.
INPUT
Use this button to make Dsub
feature is used when two
display.
The default
or
BNC connector active. This
computers
setting
are
connected to the
is Dsub. The LED is turned
on
for
the D-sub connector and is turned off for the BNC connector.
A6
On Screen
Screen
Display (OSD) Control Adjustment
Adjustment
Making adjustments to the image size, position and operating parameters of
the monitor is quick and easy with the On Screen Display Control system.
A short example is quick and easy given below to familiarize you with the use
of the controls. The following section is an outline of the available
adjustments and selections you can make using the OSD.
NOTE
Allow the monitor to stabilize for at least 30 minutes before
To make
adjustments
in the On Screen
making image adjustments.
Display, follow these steps:
Case 1
Case 2
Press the MENU (or OSD) Button, then the main
menu
of the OSD
appears.
To
access a
becomes
control,
use
highlighted,
Use the
the
Buttons. When the icon you want
or
press the SELECT (or SET) Button.
Buttons to
adjust the item
to the desired level.
Accept the changes by pressing the SELECT (or SET) Button.
Exit the OSD
by pressing the MENU (or OSD) Button.
A7
On Screen
The
and
Display(OSD)
Selection and
Adjustment
following table indicates all the On Screen Display control, adjustment,
setting menus.
Main
Sub
menu
Reference
menu
To
Brightness
BRIGHTNESS/
CONTRAST
POSITION
SIZE
Contrast
V Position
To
H Position
screen
V Size
To
adjust the
and
To
adjust the shape
adjust the position
of the
size of the
screen
H Size
Tilt
SHAPE
adjust the brightness
contrast of the screen
of the
screen
Side Pincushion
S Pincushion Balance
Parallelogram
Trapezoid
H Corner
Top Corner
Bottom Corner
Recall
Zoom
H
V
Linearity
Linearity
Recall
PRESET
COLOR
6500K
To customize the color of the
9300K
screen
Temp
R/G/B(User Color)
:
Adjustable
NOTE
The order of icons may differ
depending
A8
on
the model
(A10~A14).
On Screen
Main
Display(OSD)
menu
SETUP
Sub
Selection and
Adjustment
Reference
menu
Video Level
To customize the
Language
for
a
user's
screen
operating
status
environment
OSD Time
OSD Position
Reset
Clamp
Degauss
SPECIAL
To
improve the clarity
stability of the screen
Natural Color
and
Auto
Sizing
Sharpness
Moire
H Moire
V Moire
Purity
Convergence
:
Adjustable
NOTE
The order of icons may differ
depending
A9
on
the model
(A10~A14).
On Screen
You
were
Display(OSD)
introduced to the
Selection and
Adjustment
procedure of selecting and adjusting an item
the OSD
using
descriptions
To
system. Listed below are the icons, icon names, and icon
of the all items shown on the Menu.
adjust the brightness and
OSD
contrast of the
Adjust
screen
Description
Brightness
adjust the brightness
To
of the
screen.
Contrast
To
To
adjust the position of the
OSD
adjust the
contrast of the
screen.
screen
Adjust
Description
Vertical Position
To move image up and down.
Horizontal Position
To move image left and
To
adjust the
OSD
size of the
screen
Adjust
Description
Vertical Size
To
adjust image height.
Horizontal Size
To
A10
adjust image width.
right.
On Screen
To
Display(OSD)
Selection and
adjust the shape of the
OSD
Adjustment
screen
Adjust
Description
Tilt
To correct
image
rotation.
Side Pincushion
To correct
the
a concave or convex
bowing
of
image.
Side Pincushion Balance
To correct the balance of both sides
bowing.
Parallelogram
correctly adjust the
To
skew of the
image.
Trapezoid
To correct
H
geometric distortion.
Corner*
Top Corner*
Bottom Corner*
To correct
an irregular distortion
displayed image.
of the
Recall*
You
can use
modified
this function to reload the
parameters for screen display
operation, as specified by the user after
purchase: Side Pincushion, Side Pincushion
Balance, Parallelogram, Trapezoid H
Corner, Top Corner, Bottom Corner (These
recalled options may differ depending on the
mode selected: Preset, User, or New).
,
Zoom*
To
simultaneously adjust horizontal
image.
vertical size of the
*
This function is available for
designated
models
only.
A11
and
To
adjust the shape of the
OSD
screen
Adjust
Description
H.
Linearity*
To
adjust the
image.
the
horizontal width of
edge
of
Linearity*
V.
To
adjust the
image.
vertical width of
edge
of the
Recall*
You
can use
modified
*
operation, as specified by the user after
purchase: Zoom, H/V Linearity (These
recalled options may differ depending on the
mode selected: Preset, User, or New).
This function is available for
designated
models
only.
To customize the color of the
OSD
this function to reload the
parameters for screen display
screen
Adjust
Description
PRESET
6500K/ 9300K
Select the
TEMP
?
6500K:
?
9300K:
screen
color.
Slightly reddish white.
Slightly bluish white.
Select the
screen
prefer among
temperature which you
reddish
or
bluish
in between.
RED
GREEN
BLUE
A12
Set your
own
color levels.
or
any color
On Screen
Display(OSD)
To customize the
OSD
screen
Selection and
status for
a
user's
Adjust
Adjustment
operating environment
Description
VIDEO LEVEL This item is used to select the monitor's
input signal
level. The normal level used for
most PCs is 0.7V.
If the
out
screen
or
becomes
suddenly washed-
blurred, please select 1.0V and try
again.
LANGUAGE
To choose the
language in which the
displayed.
OSD Menus are available in 11 languages:
English, German, French, Spanish, Italian,
Swedish, Finnish, Portuguese, Korean,
control
names are
Chinese and Russian.
OSD TIME*
Set the OSD time, i.e. the length of time a
menu will remain on-screen before it shuts
off automatically.
Adjust the time to 5, 10,
20, 30 or 60 seconds.
OSD POSITION*To
adjust position of the OSD window on
the screen.
RESET*
Return to all
factory default settings
except "LANGUAGE, BRIGHTNESS,
CONTRAST": Tilt, Color 9300K, Video
Level, OSD Time, OSD Position, Moire,
Convergence (These reset options may
CLAMP*
differ depending
on
Preset, User,
New).
In
This function is available for
designated
models
only.
A13
the mode selected:
of input SOG (Sync On Green)
Signal, the back raster will appear
green. Then, to select the SOG (Sync On
Green) in the clamp, it goes back to the
original back raster.
case
Video
*
or
On Screen
To
Display(OSD)
improve
OSD
the
Selection and
clarity and stability
Adjust
Adjustment
of the
screen
Description
DEGAUSS
DEGAUSS
ON
NATURAL COLOR
OFF
AUTO SIZING
ON
SHARPNESS
To
manually demagnetize the screen to
showing incorrect images or colors.
avoid
NATURAL
This is have the real color of the
COLOR*
image.
93.6 kHz / 75.0 Hz
AUTO SIZING* This will
automatically adjust your display
image to the ideal settings for the current
screen resolution size (display mode).
SHARPNESS*
MOIRE
This is to
adjust the clearness of the
screen.
PURITY
It is recommended to
CONVERGENCE
movies
or
use
this to
see
moving picture.
93.6 kHz / 75.0 Hz
MOIRE
This item allows you to reduce the degree
of moire. (Moire is caused by interference
Horizontal Scan Line with the
periodical
screen). It is normally OFF(H:0/V:0).
The moire adjustments may affect the
dot
focus of the
Moire
screen.
adjustments may shake slightly
while the moire reduction function is
PURITY*
Use to
adjust the purity on
the color appears
*
CONVER-
This is to
GENCE*
and blue fields.
This function is available for
designated
models
only.
A14
the
on.
screen
uneven.
adjust the alignment of red
if
Troubleshooting
Check the
No
following before calling for service.
image
appears
Is the power cord of the
monitor connected?
Check and see if the power cord is connected properly to
the power outlet.
Is the power indicator light
on?
Press the Power button.
Is the power on and the
power indicator green?
Adjust the brightness and the contrast.
Is the power indicator
amber?
If the monitor is in power saving mode, try moving the
mouse or pressing any key on the keyboard to bring up
the screen.
Do you see an "OUT OF
This message appears when the signal from the PC
(video card) is out of horizontal or vertical frequency
range of the monitor. See the 'Specifications' section of
this manual and configure your monitor again.
FREQUENCY" message
on the screen?
Do you see a "SELF
DIAGNOSITICS" message
on the screen?
The
screen
is
This message appears when the signal cable between
your PC and your monitor is not connected. Check the
signal cable and try again. In case of using the BNC
connector, this message also appears in the DPM
mode. Check the signal cable or press any key on the
keyboard to bring up the screen.
flickering.
Is the vertical frequency
less than 70Hz or is your
monitor set to the
interlaced mode?
Set the vertical frequency to 72Hz or higher, and
consult the video card user manual for instructions on
converting to a non-interlaced mode.
(You can set this option under the Display icon of the
Control Panel.)
Do you have any
magnetic material such
Remove magnetic sources, such as power
adapters, speakers, or high-voltage lines, away from
adapter, or highvoltage line near to your
the monitor.
Do you hear a "~ding"
sound while the monitor
is flickering?
Use the normal degaussing function. This function
clears the screen and reduces any screen blur that
may occur due to the surrounding magnetic field. The
screen may flicker for about 5 seconds, accompanied
by a "~ding"sound.
as
monitor?
A15
Troubleshooting
The
screen
color is not normal.
Do you see basic
discoloration (16 colors)?
Set the color depth to 256 colors or higher: use 'Control
Panel'
'Display' 'Settings' 'Color Palette'
Is the screen color unstable
Check the connection of the signal cable. Or pull out
the video card of the PC and insert it again.
or monochrome?
Do you see two fine
horizontal lines on the
screen?
Two fine horizontal lines may be visible on the
screen. This is not a fault or defect of the moitor and
is normal for all aperture grille type displays.
The fine lines are the shadows of Damper Wires
which are used to reduce the susceptibility of the
CRT's aperture grille to shock or vibration.
This
happens due to interference from surrounding
magnetic fields, as created when speakers, steel
structures, or high-voltage lines are placed near the
Do you see a partial
blurring on the screen?
monitor. Remove any such materials from the
immediate vicinity and use the DEGAUSS icon
the screen adjustment menu to fix the screen.
I
see an
after-image
Do you see the after-image
even when you turn off
the monitor?
on
the
on
screen.
A premature aging of the monitor pixels may cause the
prolonged display of a single image on the screen. Be
sure to use a screen saver to
maximize the service life of
the monitor.
I
see waves on
the
screen.
Do you see the wave
directly on the screen?
This occurs in inverse proportion to the screen focus,
which can be caused by a particular frequency or video
card. Brighten the screen and use the 'MOIRE' icon on
the screen adjustment menu to adjust the screen.
Have you installed the monitor driver?
Have you installed the
monitor driver?
Be sure to install the monitor driver from the monitor
driver CD (or diskette) that comes with your monitor. Or,
you can also download the driver from our web site:
http://www.lge.com.
A16
Specifications
Picture Tube
22 inches (20 inches viewable), Natural Flat Tube
90
degree deflection
pitch
0.24mm Grille
ARAS( Anti-Reflective Anti-Static) coating
Sync Input
Video
Input
Horizontal
Freq.
Vertical Freq.
Input Form
30
50
-
-
124kHz (Automatic)
160Hz (Automatic)
Signal Input
Separate TTL, Positive/Negative
CompositeTTL, Positive/Negative
SOG(Sync On Green)
15 pin D-Sub / 5 BNC Connector
Input Form
Separate, RGB Analog, 0.7Vp-p/75 ohm,
Resolution(max)
2048
Plug&Play
DDC 1/2B
Power
Normal
≤
Stand-by/Suspend
≤
Power Off
≤
Dimensions
Width
50.3cm / 19.8 inches
&Weight
(with tilt/ swivel
stand)
Height
Depth
50.9
cm
47.7
cm
Net
31.3
kg (69.0 lbs)
Power
AC 100-240V 50/60Hz 2.0A
Operating Conditions
Consumption
Input
Environmental
Conditions
Temperature
Humidity
115W(130W)
8W(20W)
3W(18W)
*(
) : with USB
/ 20.4 inches
/ 18.8 inches
5˚C to 35 ˚C
10 % to 90 %
non-Condensing
Storage Conditions
-20˚C to 60 ˚C
Temperature
5 % to 90 % non-Condensing
Humidity
Tilt/Swivel Stand
Signal
cable
), Detached ( O )
Attached(
), Detached ( O )
Attached(
Power cord
Attached
Regulations
TCO99
or
Detached
NOTE
Information in this document is
subject to change without
A17
Positive
1536@75Hz
x
notice.
Preset Modes
123456789
(Resolution)
VESA
640
x
480
31.47
60
VESA
800
x
600
53.68
85
VESA
1024
768
60.02
75
85
VESA
x
768
68.68
VESA
1280
x
1024
79.98
75
VESA
1280
x
1024
91.15
85
VESA
1600
x
1200
93.75
75
85
75
1024
x
VESA
1600
x
1200
106.25
VESA
2048
x
1536
121.95
Using
the BNC connector with other types of video cards
Using the BNC connectors with other types of video cards. Follow the
example that fits your needs.
1.
case of using a composite sync on green video signal(Sync On Green):
Connect each R,G and B video signals to BNC receptacles on the back of the
monitor.
In
B
G
Green
Blue
2.
R
Red
case of using an external composite sync signal:
Connect each R, G and B video signals and composite sync signal to the BNC
receptacles on the rear panel.
In
B
G
R
*
COMP.
HD
*
Varies according to model.
Green
Gray
3.
Red
Blue
case of using a separate horizontal and vertical sync signal:
Connect each R, G and B video signals and the horizontal and vertical sync
signal to BNC receptacles on rear panel.
In
B
G
R
*
COMP.
HD
VD
Green
*
Varies according to model.
Gray
Black
Blue
Red
NOTE
This
package does not include the BNC connectors
purchase them at your local computer stores.
This monitor does not support the DDC function, if you
5 BNC connectors with other types of video cards.
A19
but you
use
the
can
HD
:
Horizontal Drive
VD
:
Vertical Drive
COMP
:
Composite
Making
use
of USB
(Universal Serial Bus)
USB (Universal Serial Bus) is
innovation in
connecting your different
desktop peripherals conveniently
By using the USB, you will
be able to connect your mouse, keyboard, and other peripherals to your
monitor instead of having to connect them to your computer. This will give you
greater flexibility in setting up your system. USB allows you to connect a chain
of up to 120 devices on a single USB port; and you can "hot" plug (attach them
while the computer is running) or unplug them while maintaining the Plug and
the Plug auto detection and configuration. This monitor has an integrated BUSpowered USB hub, allowing up to 4 other USB devices to be attached it.
an
to your computer.
USB connection
1. Connect the upstream port
compliant PC
USB port)
2.
or
of the monitor to the downstream port of the USB
another hub using the USB cable. (Computer must have a
Connect the USB compliant peripherals to the downstream ports of the
monitor.
This is a simplified representation
This is a simplified
of the rear view.
of the side view.
representation
USB downstream Ports
To USB downstream
connect the cables from USB
of the USB
compliant peripherals-such
keyboard, mouse, etc
or
port
compliant PC
another hub cable
NOTE
To activate the USB hub function, the monitor must be connected to
PC(OS) or another hub with the USB cable(enclosed).
When connecting the USB cable, check that the
matches the shape at the connecting side.
shape
a
USB
compliant
of the connector at the cable side
Even if the monitor is in a power saving mode, USB compliant devices will function when
connected the USB ports(both the upstream and downstream) of the monitor.
they are
A20
as
Making
use
USB
of USB
(Universal Serial Bus)
Specifications
USB standard
Rev. 1.1
complied BUS-powered hub
Downstream power supply
Communication speed
500mA for each (MAX)
USB port
1
12
Mbps (full), 1.5 Mbps (low)
Upstream port / 4 Downstream ports
IMPORTANT: These USB connectors are not designed for use with
such as a video camera, scanner, etc. LGE recommends connecting
directly to
the computer
A21
high-power
high-power
USB devices
USB devices
Download PDF