LG | S-W-995E-PLUS-CB995D-UP | LG STUDIOWORKS 995E(CB995D-EP) Owner’s Manual

Table of Contents
Introduction
Introduction
Important
Installation
Precautions
Connecting the Monitor
Making use of USB (Universal Serial Bus)*
Operation
Location and Function of Controls
Control Panel Function
Technical Information
On Screen
Display (OSD) Control Adjustment
On Screen
Display(OSD) Selection and Adjustment
Energy Saving Design
Low Radiation
Video
Compliance (MPR II) and DDC (Display Data Channel)
Memory Modes
Troubleshooting
Service
Specifications
*
Applies
to 995E
plus only.
Introduction
Introduction
Thank you for purchasing a high resolution monitor. It will give you
high resolution performance and convenient reliable operation in a
variety of video operating modes.
Features
The monitor is
a 19 inches (18.0 inches viewable ) intelligent,
microprocessor based monitor compatible with most analog RGB (Red,
Green, Blue) display standards, including IBM PC , PS/2 , Apple ,
Macintosh , Centris , Quadra , and Macintosh II family.
USB (Universal Serial Bus) ports at the back of the monitor are prepared
can easily and flexibly connect USB-
for the USB cable and hub. You
designed devices-such as a mouse, keyboard
for true Plug and Play function.*
or
printer- to the
monitor
The monitor
provides crisp text and vivid color graphics with VGA,
SVGA, XGA, and VESA Ergonomic modes (non-interlaced), and most
Macintosh compatible color video cards when used with the appropriate
adaptor. The monitor's wide compatibility makes it possible to upgrade
video cards or software without purchasing a new monitor.
*
Applies
to 995E
Monitor
rear
horizontal
Registration
The model and serial numbers
the
Digitally controlled auto-scanning is done with the micro-processor for
scan frequencies between 30 and 96kHz, and vertical scan
frequencies between 50-160Hz. The microprocessor-based intelligence
allows the monitor to operate in each frequency mode with the
precision of a fixed frequency monitor.
plus only.
are
found
of this unit. These numbers
unique to this
on
a
of
producing
a
maximum horizontal resolution of
maximum vertical resolution of 1200 lines. It is well
sophisticated windowing
environments.
unit and not available to
For low cost of monitor
operation, this monitor is certified as meeting
Energy
requirements, and utilizes the VESA Display Power
Management Signalling (DPMS) protocol for power saving during nonuse periods.
requested
guide as a
your purchase. Staple
information here and retain this
permanent record of
receipt
capable
1600 dots and
suited for CAD work and
are
others. You should record
your
This monitor is
the EPA
here.
Date of Purchase
:
Dealer Purchased From
:
Dealer Address
:
Dealer Phone No.
:
Model No.
:
Serial No.
:
A1
Star
Introduction
Precautions
Important
This unit has been engineered and manufactured to
assure
your
result in
potential electrical
shock or fire hazard. In order not to defeat the safeguards
incorporated in this monitor, observe the following basic rules for its
installation, use, and servicing. Also follow all warnings and
instructions marked directly on your monitor.
personal safety,
On
Safety
but improper
use can
Use only the power cord supplied with the unit. In case you use another
power cord, make sure that it is certified by the applicable national
standards if not being provided by the supplier. If the power cable is
faulty in any way, please contact the manufacturer or the nearest
authorized repair service provider for a replacement.
Operate the monitor only from a power source indicated in the
specifications of this manual or listed on the monitor. If you are not sure
what type of power supply you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed
power cords and broken plugs. They may result in a shock or fire hazard.
Call your service technician for replacement.
Do not
Open
the Monitor
There
are no user
There
are
serviceable components inside.
even when the power is
Dangerous High Voltages inside,
OFF.
Contact your dealer if the monitor is not
operating properly.
To Avoid Personal
Injury :
place the monitor on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
Do not try to roll a stand with small casters across thresholds or deep
pile carpets.
Do not
To Prevent Fire
or
Hazards:
Always turn the monitor OFF if you leave the room for more than a
short period of time. Never leave the monitor ON when leaving the
house.
Keep children from dropping or pushing objects into the monitor's
openings. Some internal parts carry hazardous voltages.
cabinet
A2
Introduction
Important
Precautions
Do not add accessories that have not been
designed for this monitor.
lightning storm or when the monitor is to be left unattended
for an extended period of time, unplug it from the wall outlet.
Do not bring magnetic devices such as magnets or motors near the
picture tube.
During
On Installation
a
Do not allow
place the
Do not
anything to rest upon or roll over the power cord, and do not
monitor where the power cord is subject to damage.
use
this monitor
near
in
water such as near a
bathtub, washbowl,
kitchen sink,
laundry tub,
Monitors
provided with ventilation openings in the cabinet to allow the
generated during operation. If these openings are blocked,
are
a
wet
basement,
or near a
swimming pool.
release of heat
built-up
heat
can cause
failures which may result in
a
fire hazard.
Therefore, NEVER:
Block the bottom ventilation slots
sofa, rug,
by placing the
monitor
on a
bed,
etc.
Place the monitor in
a
built-in enclosure unless proper ventilation is
provided.
Cover the
openings with
Place the monitor
On
On
Cleaning
cloth
or
near or over a
other material.
radiator
or
heat
source.
Unplug the monitor before cleaning the face of the picture tube.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly
the picture tube because overspray may cause electrical shock.
Repacking
on
Do not throw away the carton and packing materials. They make an
ideal container in which to transport the unit. When shipping the unit
to another
A3
location, repack it in its original material.
Installation
Connecting the Monitor
Connection to any IBM
VGA PC compatible
Figure 1 shows the signal cable connections from the monitor to the
Video Graphics Array (VGA) port typical in an IBM PC or PC
compatible. This also applies to any graphics video card for PC-CAD
or workstation that has a 15 pin high density (3 row) d-Sub connector.
system
1.
Power off both the monitor and PC.
2.
Connect the 15
pin VGA
connector of the
supplied signal
cable to the
output VGA video connector on the PC. The connectors will mate only
one way. If you cannot attach the cable easily, turn the connector
upside
secure
down and try again. When mated,
the connection.
3.
Power ON the PC, then the monitor.
4.
If you
see
tighten
the thumbscrews to
the SELF DIAGNOSTICS message, check the
signal
cable
and connectors.
5.
After
using
the system, power OFF the monitor, then the PC.
D-15P
*
*
Applies
to 995E
plus only.
Power Cord
Signal
Figure
A4
1.
Cable
Installation
Connecting the Monitor
Connecting
to an
Figure 2 shows the connection to an Apple Macintosh, using a
separately purchased adapter.
Apple
Macintosh PC
1.
Power OFF both the monitor and the PC.
2.
Locate the
computer
appropriate MAC
to VGA
adapter
block at your local
store. This
adapter changes the high density 3 row 15 pin
pin 2 row connection to mate with
the other end of the signal cable to the side of the
VGA connector to the correct 15
your MAC. Attach
adapter block with 3
3.
rows.
Connect the attached
adapter block/signal
cable to the video output
on
your MAC.
4.
5.
Power ON the PC, then the monitor.
If you
see
the SELF DIAGNOSTICS message, check the
signal
cable
and connectors.
6.
After
using
the system, power OFF the monitor, then the PC.
Adapter
Applies
to 995E
plus only.
Power Cord
Signal
Figure 2.
A5
MAC6
D-15P
*
*
15P
Cable
Installation
Making use of USB (Universal Serial Bus)*
innovation in connecting your different
conveniently to your computer. By using the USB,
USB (Universal Serial Bus) is
desktop peripherals
an
you will be able to connect your mouse, keyboard, printer, and other
peripherals to your monitor instead of having to connect them to your
computer. This will give you greater flexibility in setting up your system.
USB allows you to connect chain up to 120 devices on a single USB port,
and you can "hot" plug (attach them while the computer is running) or
unplug them while maintaining Plug and Plug auto detection and
configuration. This monitor has an integrated self-powered USB hub,
allowing up to 4 other USB devices to be attached it.
1.
USB connection
Connect the upstream port of the monitor to the downstream port of
the USB
compliant PC or another hub using the USB cable (Computer
port).
2. Connect the USB compliant peripherals to the downstream ports of
must have a USB
the monitor.
USB downstream Ports
connect the cables from USB
compliant peripherals-such as
keyboard, mouse, printer, scanner,
USB
etc
upstream Port
To USB downstream
port of the USB
compliant PC or
*
Applies to 995E plus only
(A6~A7page).
keyboard
printer
USB
A6
Upstream connector
mouse
another hub cable
etc.
USB Downstream connector
Installation
Making use of USB (Universal Serial Bus)*
Example of connection
monitor
scanner
computer
keyboard
mouse
printer
NOTE
To activate the USB hub function, the monitor must be connected to
compliant PC(OS) or another hub with the USB cable(enclosed).
a
USB
When connecting the USB cable, check that the shape of the connector at the
cable side matches the shape at the connecting side.
When the monitor is not plugged into an electric socket, the
connected to the downstream ports will not operate.
peripherals
Even if the monitor is in a power saving mode, USB compliant devices will
function when they are connected the USB ports(both the upstream and
downstream) of the monitor.
USB
specifications
USB standard
Rev. 1.0
Downstream power
Communication
*
USB
Applies to 995E plus only
(A6~A7page).
port
supply
speed
complied self-powered
500mA for each
12
1
Mbps (full),
1.5
Mbps (low)
Upstream port
4 Downstream
A7
(MAX)
ports
hub
Operation
Location and Function of Controls
Front View
?
?
?
Power Button
Power Indicator
OSD Button
Digital Control
Panel
Rear View
ID Label
?
?
?
*
Applies to 995E plus only.
USB upstream
port*
USB downstream
?
AC Power
Socket
D-Sub
A8
Signal
Cable
ports*
Operation
Control Panel Function
Front Panel Controls
Power Indicator
OSD Button
Use this button to enter
exit the
on screen
The power indicator
or
light
is shown in the
power button. This indicator lights up green
when the monitor operates normally. If the
display.
monitor is in DPM
(Energy Saving) mode
(stand-by/ suspend/power off), this indicator
color changes to amber.
?
?
?
?
?
?
?
?
Buttons
Power Button
Use these buttons to
Use this button to enter
choose
a
in the
A9
SET Button
or
adjust
on screen
items
display.
selection in the
screen
display.
on
Use this button to turn
the monitor
on or
off.
Operation
On Screen
Display (OSD) Control Adjustment
Making adjustments to the image size, position and operating
parameters of the monitor are quick and easy with the On Screen
Display Control system. A quick example is given below to familiarize
you with the use of the controls. Following section is an outline of the
available adjustments and selections you can make using the OSD.
NOTE
Allow the monitor to stabilize for at least 30 minutes before
making image
adjustment.
To make
12
adjustments
A10
Display,
Press the OSD Button, then the main
To
acces a
control,
want becomes
Use the
345
in the On Screen
Accept
the
use
the
changes by pressing
Exit the OSD
or
highlighted, press
Buttons to
by Pressing
menu
follow these steps:
of the OSD appears.
Buttons. When the icon you
the SET Button.
adjust
the item to the desired level.
the SET Button.
the OSD Button.
Operation
On Screen
Selection and
Display(OSD)
Adjustment
You
item
were
introduced to the
using
procedure of selection and adjusting an
the OSD system.
Listed below
are
the
icons, icon names, and icon descriptions of the
items that are shown on the Menu.
OSD
Adjust
Description
Brightness
BRIGHTNESS/CONTRAST
Used to
adjust
the
brightness
of the
screen.
Contrast
the
desired.
Adjust
PRESET
display
6500K/ 9300K
To appear the
COLOR
to the contrast
displays
color
temperature.
?6500K:Slightly
?9300K:Slightly
reddish white.
bluish white.
TEMP
User easily color set without
adjustment Red, Green and Blue
(R/G/B).
RED
To set your
To set your
own
color levels.
GREEN
own
color levels.
BLUE
To set your
own
color levels.
Vertical Position
To
move
image
up and down.
POSITION
Horizontal Position
To
move
right.
A11
picture image
left and
Operation
On Screen
Display(OSD)
Adjustment
OSD
Selection and
Adjust
Description
Vertical Size
To
SIZE
adjust image height.
Horizontal Size
To
adjust image
width.
Side Pincushion
To correct the
bowing
in and out of the
image.
Side
SHAPE
pincushion
balance
To correct the balance of both sides
bowing.
Trapezoid
To correct
geometric
distortion.
Parallelogram
This control
of the
Top
adjusts for
image.
skewing
Corner
To correct the
the
a
screen
irregular
displayed image.
distortion of
Bottom Corner
To correct the
the
irregular
displayed image.
distortion of
Tilt
To correct
A12
image
rotation.
Operation
On Screen
Display(OSD)
Adjustment
OSD
Selection and
Adjust
Description
VIDEO LEVEL This item is used to select the monitor's
input signal level. The normal level
used for most PC's is 0.7V.
When the screen suddenly gets
brightened or blurry, please select 1.0V
and try again.
SETUP
DDC
To select the DDC
function(ON/OFF).
LANGUAGE To choose the language in which the
control names are displayed.
OSD POSITION To
on
CLAMP
adjust position
the
of the OSD window
screen.
There
are two signal types:
SEP(Separate or Composite Signals)
and SOG(Sync On Green). The
monitor automatically detects the
signal types and displays either of
them.
DEGAUSS
To manually demagnetize the
which may show some image
screen
or
color
incorrectly.
RECALL
If the monitor is
operating
in
a
factory
preset mode, this control will reset the
image to the factory preset mode.
SPECIAL
MOIRE
This item allows you to reduce the
moire (Moire is caused by interference
Horizontal Scan Line with the
periodical dot screen). It is normally
OFF(H:0/V:0).
The moire adjustments
may affect the
focus of the screen.
The screen image may shake slightly
while the moire reduction function is
on.
CONVERGENCE This item allows you to adjust the
horizontal convergence.
The horizontal convergence control
adjust the alignment of the red and
blue horizontal fields.
A13
Technical Information
Energy Saving Design
complies with the EPA's Energy Star program, which is a
designed to have manufacturers of computer equipment build
circuitry into their products to reduce power consumption during time of
This monitor
program
non-use.
This monitor also goes into its energy saving mode if you exceed the
monitor's operating limits, such as the maximum resolution of 1600x1200
or
the
frequency
refresh rates of 30-96kHz horizontal
conserve more
call it in
our
a
Green
or
50-160Hz vertical.
Energy Star PC, or a PC
with a screen blanking software following the VESA Display Power
Management Signalling (DPMS) protocol, this monitor can conserve
significant energy by reducing power consumption during periods of nonuse. When the PC goes into the energy saving mode, the monitor will go
into a suspended operation state, indicated by the Power LED light
changing from a green color to an amber color. After an extended period
in the suspended mode, the monitor will then enter a semi-OFF mode to
When this monitor is used with
or
EPA
energy. In the semi-OFF mode or DPMS OFF mode as we
the Power LED will still show an amber color.
specifications,
When you awaken your PC by hitting a key or moving the mouse, the
monitor will also awaken to its normal operating mode, indicated by the
green Power LED
consumption
Power
Consumption
can
light. By following
be reduced to the
these conventions, the power
levels:
following
Hori.
Verti.
Sync
Sync
Video
Consumption
Normal(Max.)
On
On
Normal
≤110W(130W)
Green
Stand-by
Off
On
Off
≤
8W(30W)
Amber
Suspend
On
Off
Off
≤
8W(30W)
Amber
Off
Off
≤
3W(20W)
Amber
Mode
Off
Off
Power
*(
A14
):withUSB
LED Color
Technical Information
Low Radiation Compliance (MPR II) and
DDC (Display Data Channel)
Low Radiation
Compliance
(MPR II)
This monitor meets
one
of the strictest
guidelines
available
today for
low
radiation emissions, offering the user extra shielding and an antistatic
screen coating. These guidelines, set forth by a government agency in
Sweden, limit the amount of emission allowed in the Extremely Low
Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range.
DDC
(Display Data
Channel)
DDC is
a
communication channel
over
which the monitor
automatically
informs the host system (PC) about its capabilities. This monitor has two
DDC function; DDC1 and DDC2B. DDC1 and DDC2B carry out unidirectional communication between the PC and the monitor. Under these
situations, the PC sends display data to the monitor but
control the monitor
not commands to
settings.
NOTE
PC must
support DDC functions to do this.
If your monitor is displaying a mono chrome
select the DDC OFF function.
A15
image or the wrong resolution,
Technical Information
Video
Memory Modes
The monitor has 31 memory locations for display
are factory preset to popular video modes.
Display Modes
(Resolution)
Display Modes (Resolution)
VESA
1
2345
User Modes
x
800
VESA
1024
x
VESA 1280
Modes 6-31
are
x
Freq.(kHz)
Vertical
Freq.(Hz)
480
43.269
85
600
53.674
85
768
68.677
85
1024
91.146
85
1200
93.750
75
x
x
VESA 1600
detects
one
640
VESA
Horizontal
modes, 5 of which
empty and
can
accept
new
video data. If the monitor
video mode that has not been present before or is not
of the preset modes, it stores the new mode automatically in one
a new
of the empty modes
If you
use
starting with
mode 6.
up the 26 blank modes and still have
more new
modes, the monitor replaces the information in the
user
video
modes
starting
with mode 6.
Recalling Display
Modes
When your monitor detects a mode it has seen before, it automatically
recalls the image settings you may have made the last time you used
that mode.
You may, however, manually force a recall of each of the 5 preset
modes by pressing the Recall button. All preset modes are
automatically
recalled
as
the monitor
senses
the
incoming signal.
The
ability to recall the preset modes is dependent on the signal
coming from your PC's video card or system. If this signal does not
match any of the factory modes, the monitor automatically sets itself
display the image.
A16
to
Technical Information
Troubleshooting
Check the
following before calling for service.
SELF DIAGNOSTICS message.
The signal cable is not connected, or is loose. Check and secure the
connection.
OUT OF FREQUENCY message appears.
The frequency of the signal from the video card is outside the operating
range of the monitor.
*Horizontal Frequency : 30-96kHz
*Vertical Frequency : 50-160Hz
Use the
graphics board's utility software
(Refer to the manual for graphics board).
to
change
the
frequency setting
The power LED is illuminated amber.
Display power management mode.
There is no active signal coming from the PC.
The signal cable is not fastened securely.
Check the computer power and graphics adapter
The
image on the SCREEN
rectangle shape.
configuration.
is not centered,
or
too
small,
or
not a
Image adjustment
yet in the current operating mode. Use
buttons to set the image to your liking.
not been done
the OSD, SET and
The monitor doesn't enter the power
saving
(Amber).
off mode
Computer video signal is not VESA DPMS standard. Either the PC or the
video controller card is not using the VESA DPMS power management
function.
NOTE
If the power indicator(LED)
condition of the monitor.
light
is
blinking amber,
Then press a power ON/OFF button on the front
service technician for more information.
A17
may result in abnomal
panel
control and call your
Technical Information
Service
Unplug the monitor from the wall outlet and refer servicing to
qualified service personnel when :
The power cord or plug is damaged or frayed.
Liquid has been spilled into the monitor.
The monitor has been exposed to rain or water.
The monitor does not operate normally following the operating
instructions. Adjust only those controls that are covered in the
operating instructions. An improper adjustment of other controls may
result in damage and often requires extensive work by a qualified
technician to restore the monitor to normal operation.
The monitor has been dropped or the cabinet has been damaged.
The monitor exhibits a distinct change in performance.
Snapping or popping from the monitor is continuous or frequent while
the monitor is operating. It is normal for some monitors to make
occasional sounds when being turned on or off, or when changing
video modes.
Do not attempt to service the monitor
removing
covers
hazards. Refer all
A18
yourself, as opening or
dangerous voltage or other
qualified service personnel.
may expose you to
servicing
to
Technical Information
Specifications
Sync Signal Types
H.Sync.
V.Sync.
Separate Sync.
H.
V.
Composite Sync.
H/V.
Priority
Type
123
(N.C
Signal Connector
Pin Assignment
:
Sync.
No
On Green
Sync.
Sync.
N.C
Sync.
N.C.
N.C
Connection)
15pin VGA Connector
5
1
6
10
15
Pin
11
Pin
Signal(D-Sub)
Red
NOTE
12345678
Signal(D-Sub)
N.C.
Green
10
Ground
Blue
11
Ground
Ground
12
SDA
Self-Test
13
H.
Sync.
Red Ground
14
V.
Sync.
Green Ground
15
SCL
Blue Ground
No. 5 Pin have to
A19
9
ground
on
the PC side.
Technical Information
Specifications
Picture Tube
(18.0 inches viewable) FST
degree deflection
0.26mm dot pitch
ARAS (Anti-Reflective Anti-Static) Coating
19 inch
90
Sync Input
Horizontal
30
Vertical
50 -160Hz
Input
Freq.
Freq.
Form
15
Signal Input
Video
Input
Input
Form
Dimensions
tilt/swivel
stand)
Power
Input
pin D-Sub Connector
Separate,
Resolution
(with
96kHz
(Automatic)
(Automatic)
Separate TTL, Positive/Negative
Composite TTL, Positive/Negative
SOG (Sync On Green)
-
RGB
Analog, 0.7Vp-p/75 ohm,
1600
x
Recommend 1280
x
1024
x
max
Positive
@75Hz
@85Hz
768 @85Hz
1200
1024
Width
44.80
cm
/ 17.6 inches
Height
Depth
46.50
cm
/ 18.3 inches
47.60
cm
/ 18.7 inches
Europe
AC 200--240V 50Hz 1.5A(995E/995E plus)
Others
AC 100--240V 50/60Hz 2.0A(995E)
AC 100--240V 50/60Hz 2.5A(995E plus)
The
products
should be used
according
to the Power
requirements
each ID LABEL.
Weight
Net
Environmental Conditions
21kg (46.3 lbs)
Operating Condition
10 ˚C to 40 ˚C
Temperature
10 % to 90 % non-Condensing
Humidity
Condition
Storage
0 ˚C to 60 ˚C
Temperature
5 % to 90 % non-Condensing
Humidity
NOTE
Information in this document is
A20
subject to change without
notice.
of
Download PDF

advertising