LG | BIDLGH | LG BIDLGH Owner’s Manual

INSTALLATION AND OPERATING INSTRUCTIONS
BUILT-IN GAS COOKTOPS
To avoid the risk of accidents or damage to the Gas Cooktops, it is
essential to read these operating instructions before it is installed or
used for the first time.
And please keep this manual for later reference.
BIDLGH
P/No.: MFL62060329
www.lg.com
Contents
Introduction ................................................................................. 3
1. Instructions for safe and proper use........................................3
Instructions for the installer ....................................................... 5
2. Positioning of the hob..............................................................5
3. Electrical connection...............................................................7
4. Gas connection.......................................................................8
5. Adaptation to different types of gas.......................................10
6. Final operations.....................................................................13
Instructions for the user ........................................................... 15
7. Using the hob........................................................................15
8. Cleaning and maintenance...................................................17
These instructions are valid only for the end user countries
whose identification symbols appear on the cover of this
manual.
INSTRUCTIONS FOR THE INSTALLER: these are for the
authorised person who must carry out a suitable check of the gas
system, install the appliance, set it functioning and carry out an
inspection test.
INSTRUCTIONS FOR THE USER: these contain user advice,
description of the commands and the correct procedures for
cleaning and maintenance of the appliance.
2
Introduction
1. Instructions for safe and proper use
This manual is an integral part of the appliance and therefore must
be kept in its entirety and in an accessible place for the whole
working life of the cooker. We advise reading this manual and all
the instructions therein before using the cooker. Also keep the
series of nozzles supplied. Installation must be carried out by
qualified personnel in accordance with the regulations in force. This
appliance is intended for domestic uses and conforms to current
regulations in force. The appliance has been built to carry out the
following functions: Cooking and heating-up of food. All other
uses are considered improper.
The manufacturer declines all responsibility for improper use.
Do not leave the packing in the home environment. Separate the
various waste materials and take them to the nearest special
garbage collection centre.
It is compulsory that the appliance be grounded according to the
methods required by safety rules.
The plug to be connected to the power cable and the socket must
be the same type and must conform to current regulations.
The socket must be accessible after the appliance has been built in.
Never unplug by pulling out the cable.
Immediately after installation carry out a brief inspection test of
the appliance, following the instructions below. Should the
appliance not function, disconnect it from the supply and call the
nearest technical assistance centre.
Never attempt to repair the appliance.
Always check that the control knobs are in the position
“ZERO”(OFF) when you finish using the hob.
3
Introduction
The identification plate, with technical data, serial number and
marking is clearly visible under the casing.
The plate on the casing must not be removed.
Before connecting the device, make sure that it has been regulated for
the type of gas that will feed it, checking the label under the casing.
Do not put pans without perfectly smooth and flat bottoms on the
cooking hob grids.
Do not use recipients or griddle plates that extend beyond the
external perimeter of the hob.
The hob is to be used by adults only. Do not let unsupervised
children play with the hob.
This appliance is designed for cooking food and it shall not be used
as a space heater.
Do not spray aerosols in the vicinity of this appliance while it is in
operation.
The manufacturer declines all responsibility for damage to
persons or things caused by non-observance of the above
prescriptions or by interference with any part of the appliance or by
the use of non-original spares.
DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE
APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE.
DO NOT MODIFY THIS APPLIANCE
4
Instructions for the installer
2. POSITIONING OF HOB
The following operation requires building and/or carpentry work so
must be carried out by a competent tradesman.
Installation can be carried out on various materials such as
masonry, metal, solid wood or plastic laminated wood as long as
they are heat resistant (T 90°C).
Never use silicone or other insulating products when installing the
appliance; use only the rubber gasket provided.
2.1. Attachment to support structure
Create an opening with the dimensions shown in the figure in the
top surface of the counter, keeping a minimum distance of 50 mm
from the rear border. This appliance can therefore be mounted
against walls higher than the work surface on condition that a
certain distance “X” be kept between the appliance and the wall as
shown in the figure so as to avoid damage from overheating.
Make sure there is a minimum of 750 mm between the hot plate
flames and any shelf that may be installed directly above them.
5
Instructions for the installer
Accurately position the gasket provided all around the outer edge of
the hole in the top surface as shown in the figures below, pressing it
down so as to make it adhere properly. For measurements, refer to
the figure depending on the hob model to be installed, bearing in
mind that in both models the front and rear sides must skim the hole.
Secure the hob to the counter with brackets A (supplied). Carefully
trim any excess from border B of the gasket. The distances in the
following drawing refer to the hole on the inner side of the gasket.
In case of installation on a hollow compartment with doors, a
separating panel has to be placed under the hob. Keep a minimum
distance of 10 mm between the bottom of the unit and the panel
surface. The panel has to be easily removable to allow access in
the event of technical service.
6
3. Electrical connection
Make sure that the voltage and capacity of the power line conform
to the data shown on the plate located under the casing. Do not
remove this plate for any reason.
The plug on the end of the supply cable and the wall socket must
be the same type and conform to the current electrical system
regulations. Check that the power line is adequately grounded.
On the power line, install an omnipolar cut-off device with contact
cut-off distance greater than or equal to 3 mm, located in an easily
accessible position near the unit.
Do not use reducers, adapters or shunts.
If the power cable is replaced, the wire section on the new cable
must not be less than 1.5 mm2 (3 x 1.5 cable), keeping in mind
that the end to be connected to the hob must have the ground
wire (yellow-green) longer by at least 20 mm. Use only
H05RR-F cable or similar which has a maximum temperature
of 90°C. Any replacement needed should be carried out by a
specialised technician who should make the mains connections
according to the following diagram.
L = red
N = black
= yellow-green.
The manufacturer will not be liable for any damage to
persons or property caused by non-observance of the above
instructions or deriving from the tampering of even a single part
of the hob.
7
Instructions for the installer
4. GAS CONNECTION
Connection to the gas mains may be made with a rigid copper pipe
or with a flexible pipe and conforming to the provisions defined by
standard regulations in force.
To facilitate connection, fitting A on the rear
of the appliance may be adjusted laterally.
For this purpose, loosen hexagon nut B,
turn fitting A to the desired position, and
retighten hexagon nut B. Use a soapy
solution to check for proper tightness.
Never use a free flame.
The hob has been inspected for LPG G30/G31 at a pressure of
28-37 mbar. For use with other types of gases, see Section “5.
ADAPTATION TO DIFFERENT TYPES OF GAS”. The gas intake
fitting is ½ gas external threaded (ISO 228-1).
Connection with a flexible steel hose:
Make the connection to the gas mains using a
continuous wall flexible steel pipewhose
specifications comply with the applicable standard.
Carefully screw the connector 3 to the appliance’s
gas connector 1 (1/2” thread ISO228-1), placing
the seal 2 between them.
Connection with a flexible steel hose with
conical fitting:
Make the connection to the gas mains using a
continuous wall flexible steel pipewhose
specifications comply with the applicable standard.
Carefully screw the connector 3 to the appliance’s
gas connector 1 (½” thread ISO228-1), placing the
seal 2 between them. Apply insulating material to
the thread ofthe connector 3, and then tighten the
flexible steel pipe 4 to the connector 3.
8
1 1
2 2
3 3
1 1
2 2
3 3
4 4
4.1 Connection to LPG
Use a pressure regulator and make the connection to the tank
according to the provisions of standards regulations in force. Make
sure that feed pressure conforms to the levels shown in the table in
paragraph “5.2 Regulation for LPG”.
4.2 Ventilation of rooms
The hob may be installed only in rooms with permanent ventilation,
as required by standards regulations in force. The room in which
the hob is installed must have sufficient air flow to satisfy the
requirements of normal gas combustion and of necessary air
exchange in the room. The air intakes, protected by screens, must
be appropriately sized (regulations in force) and placed so as not to
be blocked in any way. The room where the oven is installed should
be suitably ventilated to avoid overheating or excess humidity
produced by cooking, and in the case of lengthy use a window
should be opened or the speed of any ventilators should be
increased.
4.3 Discharge of combustion products
Discharge of combustion products must be guaranteed by means of
hoods connected to a natural draught flue with certain efficiency, or
by means of forced aspiration.
An efficient aspiration system requires careful planning by a
specialist capable of installing it, respecting the positions and
distances prescribed by standards. After installation, the installer
must issue a certificate of conformity.
9
Instructions for the installer
5. ADAPTATION TO DIFFERENT TYPES OF GAS
Before performing any cleaning or maintenance work, detach
the appliance from the electrical socket.
The hob has been inspected for LPG G30/G31 at a pressure of
28-37 mbar. For functioning with other types of gas the nozzles
must be replaced and the primary air adjusted.
To replace the nozzles and regulate the burners, you have to
remove the top as described in the following paragraph.
5.1 Removing the hob
1. Remove all the knobs, the grids, the burner caps and the
flamecaps;
2. remove the screws and the nuts A that secure the burner
supports;
3. remove plates B;
4. lift the hob from its seat;
5. replace the burner nozzles in accordance with the reference gas
chart;
6. regulate the primary air as described in paragraph “5.2
Regulation for LPG”.
10
5.2 Regulation for LPG
Loosen screw A and push support B all the way. Use a double head
wrench to remove nozzle C and assemble the suitable one,
following the instructions indicated in the reference charts, with
respect to the type of gas to use. The screwing torque of the nozzle
should never exceed 3 Nm. Reposition support B so that nozzle C
is covered perfectly.
Move the Venturi tube D to regulate the air flow until distance "X" is
reached indicated in the chart in paragraph "5.4 Regulation of
primary air” and then secure the tube by means of screw A. After
the regulations have been carried out, restore the seals with sealing
wax or equivalent material.
Burner
Rated
heating
capacity
(kW)
LPG - G30/G31 28/37 mbar
Nozzl
diameter
1/100 mm
By-pass
mm
1/100
Reduced
flowrate
(W)
Flowrate
g/h G30
Flowrate
g/h G31
Auxiliary (1)
1.05
48
30
33(*)
380
76
75
Semi-rapid (2)
1.65
62
30
33(*)
380
120
118
Rapid (3)
2.55
76
37
40(*)
650
185
182
Rapid (4)
3.1
85
43
45(*)
750
225
222
Ultra rapid (5)
3.9
95
1600
283
279
65
(*) By-pass value for valveless appliances.
11
Instructions for the installer
5.3 Regulation for natural gas
The hob has been inspected for LPG G30/G31 at a pressure of
28-37 mbar. To allow the unit to work with this type of gas, perform
the same operations described in paragraph “5.2 Regulation for
LPG”, but choose the nozzles and regulate the primary air for
natural gas, as shown in the following table and in paragraph "5.4
Regulation of primary air”. After the regulations have been carried
out, restore the seals with sealing wax or equivalent material.
Burner
Natural gas - G20 20 mbar
Rated heating
capacity (kW)
Auxiliary (1)
Semi-rapid (2)
Rapid (3)
Rapid (4)
Ultra rapid (5)
Nozzl diameter 1/100 mm
Reduced flowrate (W)
73
92
115
126
140
380
380
650
750
1400
1.05
1.65
2.55
3.1
3.9
5.4 Regulation of primary air
Referred to distance “X” in mm.
BURNER
Auxiliary (1)
Semi-rapid (2)
Rapid (3)
Rapid (4)
Ultra rapid (5)
G20
G20/G31
20 mbar
28/37 mbar
2.0
1.5
2.0
2.5
2.0
2.0
1.5
5.0
10.0
4.0
To identify the burners on your hob, refer to the drawings in point
“6.3 Arrangement of burners on hob “
12
6. Final operations
Having carried out the above adjustments, reassemble the
appliance following, backwards, the instructions in paragraph “5.1
Removing the hob”.
6.1 Regulation of minimum for natural gas
Replace the components on the burner and slide
the knobs on the gas tap pins.
Light the burner and set it at minimum position.
Remove the knob and turn the regulation screw
inside or next to the gas tap pin (depending on the
model) until you get a suitable minimum flame.
Replace the knob and check burner flame
stability:
(rapidly turning the knob from maximum to
minimum position, the flame should not go out).
6.2 Regulation of minimum for LPG
To regulate the minimum for LPG, completely tighten (clockwise)
the screw inside or next to the gas tap pin (depending on the
model). The diameters of the by-passes for each burner are given
in table “5.2 Regulation for LPG”.
After having regulated the device with gas other than the one
tested, replace the label located on the guard with the one that
corresponds to the new gas. The label is inside the bag that
contains the nozzles provided.
13
Instructions for the installer
6.3 Arrangement of burners on hob
BURNERS
1. Auxiliary
2. Semi-rapid
3. Rapid
4. Rapid
5. Ultra rapid
6.4 Lubrication of gas taps
After a while, the gas tap may become hard to turn or lock. If this
happens, it has to be cleaned inside and re-greased.
This must be done by a qualified technician.
14
Instructions for the installer
7. Using the hob
Before turning on the burners, make sure that the burner rings,
caps and grids have been fitted correctly.
In the Wok burner, notch A must be aligned with pin B.
Grid C provided is intended for use with woks (Chinese pans).
Adapter D comes only with open grids models and is intended
for use with small sized vessels.
Some models do not feature all accessories.
7.1 Ignition of the burners
For each knob the corresponding burner is indicated. The device is
fit with electronic ignition. Simply press and simultaneously turn the
knob counter-clockwise on the low point flame symbol, until the
burner is ignited. Concerning models with valves, push the knob for
approximately 2 seconds in order to keep the flame burning and to
activate the safety device. The burner might go off when the knob is
released. In this case repeat the aforesaid operation keeping the
knob pressed for more than 2 seconds.
Should the burners go off accidentally in the models with valves,
a safety device will trip after approximately 20 seconds to block
the gas outlet even if the tap is open.
15
Instructions for the user
7.2 Practical advice for using the burners
For better burner performance and minimum
gas consumption, flat bottomed, even recipients
must be used, with covers and proportional in
size to the burners (see paragraph “7.3
Diameter of containers”). To avoid overcooking
or damage to the surface top while cooking, all
recipients or griddles must be positioned within
the cooking hob perimeter and must be a
minimum distance of 3-4 cm from the knobs.
7.3 Diameter of containers
(*)
1
2
3
4
5
Burner
Ø min. and max. (in cm)
Auxiliary
Semi-rapid
Rapid (3)
Rapid (4)
Ultra rapid
12-14
16-24
18-26
22-26
22-26
(*) For burner reference numbers, see page 14.
7.4 Using a griddle plate (Frying pan with a handle)
A few precautions are necessary if you wish to use a griddle plate:
• leave a gap of at least 160 mm between the edge of the griddle plate and the
side wall;
• if one of the burners close to the wooden rear wall is of triple flame type, leave
a gap of at least 160 mm between this wall and the edge of the griddle plate;
• do not allow the burner flames to extend beyond the edge of the griddle plate;
• operate the burners underneath the griddle plate for 10 minutes at maximum
power, then turn them down to the minimum setting. Never use the griddle
plate for more than 45 minutes.
16
8. Cleaning and maintenance
Never use a steam jet to clean the appliance.
Before any intervention, disconnect the power supply of the
device.
8.1 Cleaning
Clean the cooking top regularly every time you use it, obviously after
it has cooled.
8.1.1 Regular daily cleaning of the hob
In order to clean and preserve the surface, always use specific
products only, which do not contain abrasive substances or chlorinebased acid substances.
How to use: pour the product on a damp cloth and wipe the surface,
rinse thoroughly and dry with a soft cloth or deerskin.
8.1.2 Food stains or residues
Do not use metallic sponges or sharp scrapers: they will
damage the surface.
Use normal non-abrasive products and remove spots or
residuals with non-scratch sponges or, if need be, with wood or
plastic utensils.
Rinse thoroughly and dry with a soft cloth or deerskin.
17
Instructions for the user
8.2 Cleaning of cooking hob components
CAUTION: do not wash these components in a dishwasher. In
normal use of the hob, the stainless steel burner caps and
panstands tend to be burnished by the high temperature. Clean
these parts using very fine abrasive sponges or similar
commercial products. Then use a specific paste polish to
restore the steel’s shine. Your local authorised after-sales
technician is able to supply professional products for appliance
cleaning and care.
Grids, caps, flame cap crowns and burners can be
removed for ease of cleaning. Wash them in warm
water using a non-abrasive detergent, taking care to
remove all tough spots. Before remounting, allow the
components to fully dry out.
8.2.1 Ignition plugs and safety devices
For good functioning of the lighting ignition plugs and the
safety devices, keep them very clean. Check frequently
and clean with a damp cloth when necessary.
8.2.2 The cover
Clean the glass or steel cover, where mounted, with warm water.
Never use abrasive sponges or detergents. To clean the rear part of
the cooktop, remove the cover by lifting out. When finished
cleaning, refit the cover making sure to insert it correctly.
Before lifting up the cover, dry out properly.
Never lower the cover when burners or electric elements are
on or still hot.
18
WARRANTY CARD
Gas Hob
This warranty card is valid only for product
Sold by LG Electronics in Indian Market
www.lg.com/in
PURCHASER INFORMATION
PURCHASER'S NAME
ADDRESS
CITY
PINCODE
STATE
MODEL NO
SERIAL NO
DATE OF PURCHASE
INVOICE NO
DEALER STAMP
STAMP
DEALER INFORMATION
PURCHASER'S NAME
ADDRESS
CITY
PINCODE
STATE
19
LG INDIA ELECTRONICS PVT LTD
UNDERTAKES BY THIS WARRANTY
7. This warranty will automatically terminate on the expiry of
the warranty period as specified above, even if LG product
may not be in use for any time during the warranty period
for any reason.
8. In case of any unpredicted situation and spares not being
available, LG’s prevailing depreciation policy (subject to
the sole discretion of LGEIL & could be change without
prior notice) will be applied on the product as a solution.
9. Only courts in state of Delhi and places where LGEIL has
its branch office shall have the jurisdiction for settling any
claims, disputes arising under the warranty.
THE REQUIREMENT OF WARRANTY
Should your LG product fail due to a defect in material or
workmanship under normal home use during the warranty period
set forth below, Company will at it auction repair or replace the
product upon receipt of proof of original retail purchase.
This warranty is Valid only to the Original retail purchaser of the
product and applies only to a product sold in India by company
authorized dealer.
WHAT THIS WARRANTY DOES NOT COVER
1. Visiting charges of the service engineer for units installed
beyond municipal limits of the jurisdiction of company’s
Authorized Service Center. All expenses incurred in collecting
the units or parts thereof from the company’s authorized
service center, as well as expenses incurred with deputizing of
service personnel/technicians towards conveyance and other
incidentals etc. will be borne by the customer. Local Charges
for transportation and handling charges may vary from
location to location. Customers are advised to verify before. In
case the customer desires to bring the unit on its own to the
authorized service centre, the same shall be at its own risks &
consequences.
2. Reinstallation or un-installation of product based on customer
demand . Packing material if used will also be on chargeable
basis.
3. Transportation cost in case customer is shifting the product to
another location.
4. Damage resulting from operating the product in a corrosive
atmosphere or contrary to the instructions outlined in the
products owner’s manual.
5. Damage to the product caused by accidents, pests and
vermin, lightning, wind fire, floods, or acts of God.
6. Damage resulting from misuse, abuse , improper installation,
repair or maintenance. Improper repair includes use of parts
not approved or specified by LGEIL.
7. Damage or Failure caused by unauthorized modification or
alteration or if it is used for other than the intended purpose
8. Damage or Failure caused by incorrect electrical current,
voltage or inadequate electrical services, commercial or
industrial use, or use of spurious/fake accessories or
components, or cleaning products that are not approved by
LGEIL.
9. Damage caused by transportation and handling, including
scratches, dents, chips, and/or other damage to the finish of
your product , unless such damage results from defect in
materials or workmanship and is reported within fifteen (15)
days of delivery (Call 1800-180-9999)
10. Damage or missing items to any display, open box,
discounted or refurbished product.
11. Free accessories provided external to the product.
12. Damage to the product if customer gets the product repaired
from unauthorized dealer/person.
13. On removal, tampering or alteration of any serial number/
identification labels on the machine or any of its components.
14. On removal, tampering or alteration of any serial number/
identification labels on the machine or any of its components.
WARRANTY PERIOD
The LG Gas hob comes with 1 year warranty, from the
date of purchase that comprises of a 1 year warranty on all
parts except plastic part(knob),glass or glass part &consumables
from the date of purchase of the product, provided always that
the warranty card bears the rubber stamp, date and signature
of our Authorized Dealer.
*Note : If the Original date of purchase cannot be verified from the
proof of purchase,, the warranty will begin after 3 months of
manufacturing month which shall be verified from the serial
no./bar code label on the product.
WHAT THIS WARRANTY COVERS
LG Electronics India Pvt. Ltd. (LGEIL/the Company) offers
you
a limited warranty ,for the products sold within the territories
of India , that the product will be free from defects in material
and workmanship, according to the following terms and
conditions.
1. Repairs under warranty shall be carried out by an
authorized service personnel only. The details of
centralized help lines are as overleaf.
2. In case of repairs or replacement of any part/s of the unit,
this warranty will thereafter continue and remain in force
only for the unexpired period of the warranty. Replacement
of parts would be purely at the discretion of LGEIL alone.
In case the replacement of the entire unit is being made,
(subject to the sole discretion of LGEIL), the same model
shall be replaced and in the event such model has been
discontinued, it shall be replaced with the model
equivalent as deemed by LGEIL.
3. In event of repair LGEIL shall endeavor to use new parts
however in any case fresh parts are not available then
LGEIL will have every right to use refurbished parts. The
warranty on replacement model / Refurbished part shall
remain in force only for the unexpired period of the
warranty based on original purchase.
4. The company or its Authorized Service Center reserves
the right to retain any part/s or component replaced at its
discretion, in the event of a defect being noticed in the
equipment during warranty period.
5. If any colored internal or external components are
replaced, there will be commitment to ensure that the
shades match with the original or other components. The
replaced shades, patterns, tints may vary from the
customer’s unit due to continuous usage of the unit. Any
matching components changed at customer’s request will
be on chargeable basis except the component which
actually needed.
LG India Electronics Pvt Ltd
A-27, Mohan Cooperative Industrial Estate,
Mathura Road , New Delhi-110044, INDIA
Ph No: 0120 2560940
20
THIS WARRANTY IS NOT TRANSFERABLE AND
APPLIES TO ORIGINAL PURCHASHER ONLY.
COMPLETE THIS RECORD AND KEEP IT
TOGETHER WITH YOUR PURCAHSE DOCKET IN
A SAFE PLACE YOU WILL HAVE TO PRODUCE
THEM SHOULD YOU REQUIRE SERVICE UNDER
THE TERMS OF THIS WARRANTY.
BRANCH ADDRESS & TELEPHONE NUMBER
21
22
23
serviceindia@lge.com
Download PDF

advertising