LG | F1403RDS29 | LG F1403RDS29 Owner’s Manual

Cleaning and Maintenance
Warning: B efore cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric
shock.
Cleaning the water inlet filter
1
2
Turn off the
water tap
3
Unscrew the
water inlet hose
Pull out the water
inlet filter
4
Clean the filter
using a hard
bristle brush
5
Refit the inlet
filter and tighten
up the inlet hose
Cleaning the drain pump filter
1
2
Open the lower
filter cover and
pull out the drain
hose.
1. Do not use an extension cord or double adapter.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualified person to
prevent danger.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inexperienced
persons may cause injury or serious malfunctioning. Contact your local service centre.
• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst
under pressure. The electronic control unit may become unreliable at temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine
standing at room temperature for a few hours before putting it into operation.
CAUTION
The hose supplied with the machine must be used.
Old hoses may not be reused.
3
Unplug the drain
hose plug. Then
open the filter by
turning to the left
Safety instructions for use
Electrical connection
Remove any
extraneous
matter from the
pump filter
4
After cleaning, refit
the drain filter cap
and tighten it by
turning it clockwise.
insert the drain plug
5
Close the lower
cover
CAUTION
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young Children should be supervised to ensure that they do not play with appliance.
Installation of drain hose
Cleaning the dispenser drawer
Cleaning in general
Insert the dispenser drawer
ca. 105 cm
Hose
Retainer
Important: Do not use methylated spirits, solvents or similar products.
Exterior
Proper care of your washing machine can extend its service life.
The outside of the machine can be cleaned with warm water and
a neutral non-abrasive household detergent. Immediately wipe
off any spillage. Wipe with damp cloth. Avoid striking the surface
with sharp objects. Never hose down the machine!
Interior
Dry around the washing machine door
opening, flexible gasket and door
glass. Run washing machine through
a complete cycle using hot water.
Repeat process if necessary.
Tie
strap
ca. 105 cm
max. 100 cm
Clean inside the
recess with an
old toothbrush
ca. 145 cm
min. 60 cm
Clean the dispenser
drawer under
flowing water
4
ca. 100 cm
60 – 100 cm
Pull out the
dispenser drawer
3
min. 60 cm
2
ca. 145 cm
max. 100 cm
1
5 Once you
have finished
cleaning, replace
the drawer and
run a rinse cycle
without laundry or
soap.
ca. 100 cm
max. 100 cm
min. 60 cm
• The drain hose should not be placed higher than 100 cm above the floor.
• Proper securing of the drain hose will protect the floor from damage due to any water leakage.
• If the drain hose is too long do not force back into the washing machine. This will cause abnormal
noise and cause the machine to malfunction and leak.
Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating
instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these
operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before installing the appliance and putting it into operation.
• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only with cold
drinking water and only for washing textiles with washing detergents designed for washing machines. Every other use is improper
and may lead to injuries, whereby the liability of the manufacturer will cease.
• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.
• Never modify the appliance on your own, as this is dangerous.
• This appliance is heavy. Transporting with care.
• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.
• All installation work must be carried out by a qualified fitter or technician.
• Have electrical connections done by a qualified electrician.
• Never place the appliance on the power cord.
• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.
• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never disconnect
by pulling the power cord. Never touch the plug with wet fingers or hands.
• Do not overload the appliance.
• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.
• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or parts to warp.
• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fire.
• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.
• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.
Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized customer service.
• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances
(such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fire or explosion.
• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover has been
used then make sure that the solvent has been carefully washed out before inserting the clothes into the appliance. Oil may remain
in the tub after a whole cycle resulting in fire during drying. So, do not load oily clothes.
• Do not operate the appliance at locations where flammable substances are present such as oil, benzene or highly inflammable gas.
Such materials may cause fire or explosion. Never use combustible detergents.
• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.
• After washing, keep the drum door open to protect the door seal.
• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of scalding.
• Animals and children may get into the washing machine. So always check the appliance before using it.
• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.
• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.
• The product should be serviced and repaired only by the authorised customer service using original replacement parts.
• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in order to protect children.
• When placing on a carpeted floor, make sure that the opening in the socket is not blocked.
• If the appliance has been under water then contact the customer service. There is danger of electric shock and fire.
• The cover cup of the filter as well as the dispenser drawer may not be opened during the operation.
• Keep all washing powder and detergents away from children. Danger of poisoning
Safety instuctions for the installation
Safety instructions for use
To minimize the risk of fire within the inner bowl, the following should be observed:
• Items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be
placed in a tumble dryer.
Oil-affected items can ignite spontaneously, especially when exposed to heat sources Such as in a tumble dryer.
The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot
escape, the items can become hot enough to catch fire. Piling, stacking or storing oil-affected items can prevent
heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent-this will reduce,
but not eliminate, the hazard. The ‘cool down’ cycle of tumble dryers should be used to reduce the temperature
of the items. They should not be removed from the tumble dryer or piled or stacked while hot.
• Items that have been previously cleaned in, washed in, soaked in or spotted with petrol/gasoline, dry-cleaning
solvents or other flammable or explosive substances should not be placed in a tumble dryer.
Highly flammable substances commonly used in domestic environments include acetone, denatured alcohol,
petrol/gasoline, kerosene, spot removers (some brands), turpentine, waxes and wax removers.
• Items containing foam rubber (also known as latex foam) or similarly testured rubber like materials should not be
dried in a tumble dryer on a heat setting.
Foam rubber materials can, when heated, produce fire by spontaneous combustion.
• Fabric softeners or similar products should not be used during a drying cycle, to eliminate the effects of static
electricity unless this practice is specifically recommended by the manufacturer of the fabric softener or product.
• Undergarments that contain metal reinforcements should not be placed in a tumble dryer.
Damage to the tumble dryer can result if metal reinforcements come loose during drying.
When available a drying rack could be used for such items.
• Plastic articles such as shower caps or babies waterproof napkin covers should not be placed in a tumble dryer.
• Rubber-backed articles, clothes fitted with foam rubber pads, pillows, rubber boots and rubber-coated tennis
shoes should not be placed in a tumble dryer.
Install or store the appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit the power plug
to a grounded wall socket that complies with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted floor. In countries where there is a risk of cockroach
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
CAUTION about positioning the appliance
Install the washing machine on a flat hard floor. Make sure that air circulation around the washing machine is
not impeded by carpets, rug etc.
• Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine.
• If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
• The washing machine must not be installed in rooms where the temperature may drop below 0°C.
• Please ensure that when the washing machine is installed, that a Service Technician can gain easy access in the event of a
breakdown.
• Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
the top of the washing machine and underside of the worktop.
CAUTION about the power cord
We recommend connecting most appliances to a dedicated circuit which is protected by a mains fuse.. That is, a single outlet
supplying power only to the appliance concerned, without any additional outlets or branch circuits. Check the specifications
of this owner‘s manual. Do not overload wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension
cords, frayed power cords, damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect
the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or
walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
CAUTION about location and moving
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the
stopcock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no floor drain
(gully) in the immediate vicinity. If relocating the appliance use the original packing material. Packaging material (e.g. plastic film,
Styrofoam) can be dangerous for children. There is a risk of suffocation! Keep all packaging well away from children and do not
allow children to play inside the bowl as they may become trapped.
CAUTION about the floor surface
• The installation surface must be clean, dry and level.
• Install washing machine on a flat hard floor.
• Poorly constructed timber base floors can contribute to excessive noise and vibration.
• Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
• The washing machine must be perfectly level and firmly in position.
• It must not “see-saw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
@
Technical Specification
Name or product
Front loading washing machine
Max. Watt
2100 W (Wash) / 1500 W (Dry) / 1100 W (Steam)
Power supply
220-240 V~, 50 Hz
Wash capacity
9 kg (Wash) / 5 kg (Dry)
Size WxDxH mm:
600 x 640 x 850
Water consumption
73
Weight
73 kg
Permissible water pressure 1.0-10 bar (100-1000kPa)
N
Troubleshooting
• Water supply is not adequate in area
• Water supply taps are not completely
open.
• Water inlet hose(s) are kinked.
• The filter of the inlet hose(s) are clogged.
Check another tap in the house.
Fully open tap.
• Drain hose is kinked or clogged.
• The drain filter is clogged.
Clean and straighten the drain hose.
Clean the drain filter.
For more detailed information, please
refer to “Cleaning the drain pump filter”
• Load is too small.
• Load is out of balance.
• The appliance has an unbalance detection
and correction system. If individual heavy
articles are loaded (ex. bath mat, both
robe, etc.), this system may stop spinning
or even interrupt the spin cycle altogether.
• If the laundry is still too wet at the end of
the cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
• Floor is unstable.
Feet are not adjusted
Add 1 or 2 similar items to help balance
the load.
Rearrange load to allow proper spinning
• Is the door opened or not
completely closed?
• Water overfills due to the faulty water
valve.
• Water level sensor has malfunctioned.
Straighten hose(s).
Check the filter of the inlet hose(s).
Owner‘s Manual
F1403RDS2(1~9)
The floor should be a solid surface.
Adjust the feet so that the machine
does not rock from side to side or front
to back.
Close the door completely.
If the “
” does not clear, call for
service.
Unplug the power plug and call for
service.
Close the water tap.
Unplug the power plug.
Call for service.
• Over load in motor.
• Water leaks.
Call for service.
• Check water supply.
Turn the tap on.
If “
” is not released, unplug
power plug and call for service.
Rattling and clanking noise
Extraneous objects such as coins or safety pins maybe in drum or pump.
Thumping sound
Vibrating noise
Water leaks.
Excessive suds
Washing machine does not start
Heavy wash loads may produce a thumping sound. This is usually normal.
Have all transit bolts and packing been removed?
Check and tighten hose connections. Unclog drain pipe. Contact plumber if necessary.
Too much detergent or unsuitable detergent.
Power cord may not be plugged in or connection may be loose.
Washing machine won’t spin
Check that the door is shut.
Check that foreign objects may be blocking the drain causing the water not to drain out.
Door does not open
Once started, the door can not be opened for safety reasons.
At the end of the cycle or when Start Pause is pressed, wait one or two minutes before
opening the door to allow the electric locking mechanism time to release.
Before use please read carefully the safety instructions!
Thank you for buying an LG fully automatic washing machine.
Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.
Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your
washing machine.
P/No. :MFL59755591
Preparation
CHECKING THE MACHINE
Never use a defective machine! In case of any
failure, first unplug the machine and turn off the
water tap.
WATER CONNECTION
Turn on the water tap
INSERT PLUS INTO THE MAINS SOCKET
Never touch the plug with wet hands!
Never remove the plug from the socket by pulling on the cord.
DOING LAUNDRY AND USING MACHINE
WITH CARE
- empty all pockets
- remove all metal parts
- place the delicate textiles into the laundry net
- close zippers
LAUNDRY WITH DIFFERENT AMOUNTS OF
SOILING
- wash new textiles separately
lightly
- do not prewash
- pretreat dirty spots
heavily
- pre wash
Washing
temperature
Medium hot
ironing
Do not
tumble dry
Dry flat
Do not wash
Hot ironing
Hang to dry
Do not bleach
Luke warm ironing
Do not iron
Drip dry
OK. to bleach
Pre Wash
The Pre wash compartment can be used
for Normal to heavy soiled clothes, by
adding a prewash or normal detergent to
this compartment before selecting this
wash option with the Cycle.
Program
Cotton
Cotton
Quick
Synthetic
Baby Care
Allergy Care
Hand Wash
/Wool
Color fast garments (shirts,
60°C
nightdresses, pajamas...)and
(Cold, 30°C, - Time Delay
lightly soiled white cotton
40°C, 95°C) - Steam Wash
(underwear)
- Intensive
- Medic Rinse
Lightly soiled clothing and
40°C (Cold, - Pre Wash
small loads
30°C, 60°C) - Rinse+Spin
Polyamide, Acrylic, Polyester
- Rinse+
60°C
- Normal+Hold
Lightly soiled baby wear
(40°C, 95°C)
- Time Delay
- Steam Default
Cotton, underwear, pillow
- Intensive
covers, bed sheets,
60°C
- Medic Rinse
baby wear
- Rinse+Spin
- Rinse+
- Normal+Hold
Colored laundry which is
30°C
lightly soiled fast
(Cold, 40°C) - Time Delay
- Intensive
40°C
“Hand wash” marked delicate
(Cold, 30°C) - Rinse+Spin
and wool laundry
- Rinse+
30°C
Delicate laundry easily
- Normal+Hold
(Cold, 40°C)
damaged
C
Softener
Do not exceed the MAX-Level.
Highly densed softeners are to be
diluted with some water.
Excessive softener can cause brown
or grey spotting on the clothes.
Dry (Option)
- Press Power button.
- Turn the Program dial to select the program you require.
- P ress Time Delay button and set the finishing time. The machine will then automatically work out
the turn on time based on the chosen cycle.
- Press the Start/Pause button.
Control panel
Dispenser
drawer
Intensive
Power button
Program Cycle
Options
Start / Pause
Spin
Temperature
If the laundry is heavily soiled “Intensive”option is effective.
- By selecting the Intensive option, the washing duration may be extended, d epending on the program selected.
- To use this option, press the intensive button once before the wash program is started.
Fill detergent
Refer to the
written information
on the detergent's packaging
Maximum Load
Medic Rinse
C
3
B
Turn off tap
- Close water supply
- Clean the machine
- Unplug machine
Drum
A
For best results or for cleaner rinsing, select the “Medic Rinse” option.
This allows the final rinse to be heated to 40 degrees.
Available in the Cotton, Cotton Quick, Synthetic, Baby Care, and Allergy Care programs.
Medic Rinse is set by default in the Baby Care program.
The respective temperature indicator will light up.
Wash : Rating
Dryer : Less than 5kg
Wash : Less than 7kg
Dryer : Less than 5kg
- Low Temp.
- Iron Dry
- Cupboard Dry
- Eco Dry
- Time
Wash : Less than 4.5kg
Dryer : Less than 4.5kg
Less than 2.0kg
–
Note:
To use programs in
the Steam-Cycle,
please press first
the “Steam Wash”
button (see additional
programs).
Less than 3.0kg
Cotton
Cotton Quick
Synthetic
Steam Wash is
Remove laundry
- Open the door
- Remove the laundry
Select an Option
Pre Wash / Rinse+Spin
Rinse + / Normal+Hold
as
Select Spinning speed
and Washing temperature
hi
is
ng
Warning: Keep all washing powder and detergents away from children. Danger of poisoning
Baby Care
By pressing the Steam Wash button, Steam Function can be selected.
When Steam Function is selected, Steam wash (
) LED lights up.
w
The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable Woolmark products provided that the
products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine M0806.
Notes: Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for garment care.
Allergy Care
Steam Washing features enhance washing performance with low
energy consumption. Refresh cycle reduces creases in clothes.
Select a
Program
Up to 3 Items.
* Water Temperature: Select water temperature to suit wash cycles. Always follow garment manufacture’s care label or instructions when washing.
* Intensive: If the laundry is heavily soiled “Intensive” option is effective.
* Rinse + : Used to introduce an additional rinse, which may assist in removing traces of detergent residue.
* Pre Wash: If the laundry is heavily soiled, “Pre Wash” Cotton is recommended. Pre Wash is available in the Cotton, Cotton Quick, Synthetic and Baby Care program.
* Medic Rinse: For best results or for cleaner rinsing, you can choose Medic Rinse option. This heated Rinse is automatically selected on Baby Care program.
Refresh
Additional Steps
- Turn the machine off
- Leave door open to
allow drum to dry
Filter cover.
il
No Choose - Steam Default
Steam Washing and Refresh cycle
Turn the machine ON
by pressing the Power button
nt
Cotton mixed, Polyester
mixed Dress shirts, blouses
Dry
How to set “Time Delay”
tu
ECOLOGICAL WASHING
- make use of the max. washing quantity
- do not “pre wash” if possible
- use short program if possible
Option
Additional programs
ai
Refresh
DRUM CARE
- remove extraneous objects
- leave door open to dry the drum
- check the rubber seals regularly
Main Wash
For Laundry requiring detergent, place
recommended dosage in to this compartment. Please note that liquid detergent
will enter the tub as it is poured and may
not be suitable for a delay start.
Water Temp.
(Option)
Drying cycle
W
Delicate
Fabric Type
Display
Time Delay
Loading the Drum
Check the folds of the flexible gasket (grey) and remove any small articles or foreign objects that
may have fallen from items in the previous wash. .
Check all garments for loose items before loading and 2
ensure that clothes are clear of the door gasket before
closing the door so that the clothes or door gasket are
not damaged during the wash.
Washing program table
Quick 30
WATER TREATMENT
- with hardness III water
- use water softening agent
B
Additional programs
Steam Cycle
1
Allows you to set the cycle's ending time (by hourly increments) in advance.
Dispenser drawer
A
HANG UP WASTE WATER HOSE
Hose elbow connection e.g. attach to water tap
Sort the laundry
note washing instruction symbols Degree of soiling Type of textile / colour -
Washing symbols
Press Start / Pause to start or
pause the washing process
Select the
Dry mode
f in
ishe
• T his washer-dryer’s automatical process from washing to drying can be selected easily.
• F or most even drying, make sure all articles in the clothes load are similar in material and
thickness.
• D o not overload dryer by stuffing too many articles into drum. Items must be able to tumble
freely
• A fter the end of dry, “ ” is displayed. By pressing the “Start/Pause” button the
program can be ended. If you not press the “Start/Pause” button, the program is ended
after about 4 hours. “ ” Cooling Cycle.
• Use your Automatic Cycles to dry most loads. Electronic sensors measures the temperature of the exhaust to increase
or decrease drying temperatures for faster reaction time and tighter temperature control.
• Recommend Automatic drying course as a kind of clothes.
d) Eco Dry : A special cycle to reduce water usage during
a) Low Temp. : For Synthetics select
the dry cycle.
b) Iron Dry : If you want to iron clothes
e) Time (30/60/120 minutes) - 30 min. : Cotton 1.5 kg
c) Cupboard Dry : For Cottons select
- 60 min. : Cotton 3 kg
- 120 min. : Towel 5 kg
Note: T he estimated drying time varies from the actual drying time with an Automatic.
The type of fabric, size of the load, and the dryness selected affect drying time.
• By turning the DRY dial, the drying time can be selected.
• Drying course can last up to 150 min.
When selecting drying only, drying course will start after spining.
• These drying times are given as a guide to help you set your dryer for manual drying.
Drying times can vary greatly depending on dampness, room temperature and type of fabric
and your own experience will be your best guide.
Woolen Articles
- D o not tumble dry woolen articles. Pull them to their
original shape and dry them flat.
Woven and Loopknit Materials
- Do not overload your dryer
- Take out permanent press articles as soon as the
dryer stops to reduce wrinkles.
Temperature
40°C, 60°C, 95°C
No choose
60°C
1
2
Select the Refresh
program
Load 3 items or less
and close the door
3
4
Press the
Start/Pause
button
Press the Steam Wash button repeatedly until the
required and correct number of items is displayed.
Do not use detergents or softener in the Refresh
cycle.
6 3 sec.
1
6 3 sec.
2
To activate:
press and hold
the Option buttons
simultaneously until
" " appears in the
display.
Tub Clean
Change to the desired program, whilst in child lock mode:
To deactivate:
Press and hold
Press
press and hold
the Option buttons Start/
the Option buttons simultaneously
Pause
simultaneously for
3 seconds until the
" " is removed
from the display.
Permanent Press and Synthetics
Select the desired
program
Press
Start/Pause
TUB CLEAN is special cycle to clean the inside of the washing machine.
A higher water level is used in this cyle at higher spin speed. Perform this cycle regularly.
6 3 sec.
Empty the drum
completly and
close the door
2
3
Add anti-limescale
(Calgon) to the main
wash compartment.
Close the disp. drawer
Power ON with
Then press and
hold Spin and
Temp. button
4
5
Press the
After the cycle is
Start/Pause
complete, leave the
button to start Tub door open to dry
Clean process
Baby clothes and Night Gowns
- Always check the manufacture’s instructions.
Rubber and Plastics
- D o not dry any items mode from or containing rubber
or plastics, such as:
a) aprons, bibs, chair covers
b) curtains and table cloths
c) bathmats
Fiber glass
- D o not dry fiberglass articles in your dryer. Glass particles
left in the dryer could be picked up by your clothes the next
time you use the dryer and irri tate your skin.
Fiber or Leather Materials
- Always check the manufacture’s instructions.
d
6 3 sec.
1
2.Drying time guide
Program
Cotton
Cotton Quick
Synthetic
Program
Baby Care
Refresh
Allergy Care
Select this function to lock the buttons on the control panel and to prevent tampering.
Note: T he last 6 minutes of dryinng time, A sensor(Thermistor) detects clothes drying conditions. When the dryness
is low, cycle time will be added by max. 30 mins with “6” mins remaining window display.
- S ome woven and loopknit materials may shrinks, by varying
amounts, depending on their quality.
- Always stretch them out immediately after drying.
Temperature
Cold, 30°C, 40°C, 60°C, 95°C
Cold, 30°C, 40°C, 60°C
Cold, 30°C, 40°C, 60°C
Child Lock
1. Drying Automatic guide
- For heavily stained clothes, underwear, or baby clothes.
- Steam Wash is available with the Cotton, Cotton Quick, Synthetic, Baby Care, and Allergy Care programs.
- The Refresh cycle is for reducing /removing creases and wrinkles without washing. Detergent must not be
used in this Cycle.
- Do not load delicates such as wool, silk, and easily discolored clothes.
How to use Refresh Cycle
4 additional programs
Time Delay / Steam Wash / Intensive / Medic Rinse
Cold water tap must be left on during drying cycles.
3.Completion of Drying
• When drying cycle is completed, “ ” [Cool Down] is displayed on the Multi display.
• The Cool Down is setting automatically when a drying cycle is complete.
• When you are not remove a loaf of clothes from the dryer as soon as it stops, wrinkles can form.
• T he Cool Down operating periodically tumbles, rearranges and fluffs the load to tumbles, rearranges and fluffs the load to hours.
• The “ ” message will continue to display until the clothes are removed or the Start/Pause button is pressed.
Beep on / off
The Beep on/off function can be set only during the washing cycle.
To set the Beep on/off function follow the below steps. 1. Turn on the washing machine (by pressing the Power button).
2. Press the Start/Pause button.
3. Press and hold the Option and Spin button simultaneously for
three seconds to set Beep on/off function.
Once the Beep on/off function is set, the setting is memorized even
after Power is off.
Download PDF

advertising