LG | T2108VSAL | LG T2108VSAR Owner’s Manual

ENGLISH
OWNER'S MANUAL
WASHING
MACHINE
Please read this manual carefully before operating
your set and retain it for future reference
T2165VSA*
T2107VSA*
T2175VSA*
T2108VSA*
T2185VSA*
T2309VSA*
* : 1,5,H,J,K,L,R,X,Y or etc.
MFL68465615
Rev.00_210617
www.lg.com
Copyright © 2017 LG Electronics Inc. All Rights Reserved.
C ontents
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer
properly. Just a little preventive care on your part can save you a great deal of time and
money over the life of your washer. You will find many answers to common problems
in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you
may not need to call for service at all.
Page No
Introduction
Before Starting to Wash
Product Features
3
Safety Information
4
Identification of Parts
7
Function Information
8
Preparation Before Washing
9
Use of Water, Detergent, Bleach and Softener 10
Washing Programs
Special Guide for Stain Removal
13
Function of each Button
14
Normal Wash
16
Turbo Wash
16
Quick Wash
16
Strong (Jeans) Wash
16
+
Additional Function
Program
Installation
Care and Maintenance
Troubleshooting
Features & Specifications
Pre Wash Normal Wash
16
Soak Wash
18
Gentle (Wool/Saree)
19
Aqua Reserve Wash
19
TUB CLEAN
20
AIR DRY
21
Option Washing
21
DELAY START (RESERVATION) Wash
23
Other Useful Functions
24
Placing, Leveling and Installation
25
Connecting Hose
26
Grounding Method
28
Cleaning and Maintenance
29
Smart Closing Door
31
Common Washing Problems
32
Troubleshooting
33
Smart DiagnosisTM
34
Features & Specifications
35
* Product feature may vary according to different models. Refer page 35 for modelwise
features for your purchased model.
2
P
roduct Features
Washer doesn't operate while the lid is opened. If the lid is opened during the wash, rinse
or spin cycles, the operation stops for safety.
Pre Wash+ Normal
l The purpose of this program is to deliver best Wash Performance by adding extra 8 minutes of uniquely
designed washing pattern before the main wash cycle.
Jet Spray+ #
l A technology uniquely designed to spray inlet water with greater force to penetrate deep into the clothes to
bring out the best washing and rinsing performance.
Smart Closing Door
l Smart hinge prevents sudden closing of the door. Gives you a soft and safe door closing.
Turbowash
l Turbowash program delivers high wash performance in least cycle time using revolutionary
Jetspray+ technology which optimizes water & energy consumption.
Normal logic control
l A built-in load sensor automatically detects the laundry
load and a microprocessor optimizes washing conditions
such as ideal WATER LEVEL and washing time.
START
SENSING SETTING
Laundry Sensor
Water Level Sensor
Optimum
Washing
Condition
WASHING
AUTO
POWER
OFF
l Advanced technology is built into the Electronic Control System which ensures the best washing result.
TurboDrum washing
l When "Punch + 3" washing wings turn, the washing tub turns in the opposite direction.
This makes the both sides current of water which improve wash-performance by rubbing
clothes strongly.
3 Step washing
l 3 step washing makes the best washing performance with low tangling.
Rubbing
Rubbing and
Shaking
Shaking and
Disentangling
NOTE : Be sure to remove the product from the carton base, otherwise the machine
will not be able to operate properly.
Smart Diagnosis
l It is the technology to transmit the anomalies to the service center when there
is a problem with the washer. It provides the service that gives faith and trust
to the customers through precise and fast analysis.
Auto Restart
l Auto Restart allows the program to restart all by itself in case of power failure. It does from
the stage where it stopped.
# Works during Wash cycle in Normal, Pre Wash+ Normal, Turbo Wash & Aqua Reserve from WL1 to 7 and during Rinse cycle
in Normal, Pre Wash+ Normal, Turbo Wash & Aqua Reserve Programs at all water levels.
Jet Spray performance may vary with Inlet water pressure, for optimum results pressure should be > 0.9 Bar
* Product feature may vary according to different models. Refer page 35 for modelwise features for your purchased model.
3
S afety Information
Read carefully and thoroughly go through this booklet as it contains important safety information
that will protect the user from unexpected dangers and prevent potential damages to the product.
This booklet is divided into 2 parts : Warning and Caution.
: This is a warning sign specifying user’s applications which might
be dangerous.
: This is a sign specifying ‘Strictly Forbidden’ applications.
WARNING
: Failure to comply with the instructions under this
sign may result in major physical injuries or death.
CAUTION
: Failure to comply with the instructions under this
sign may result in minor physical injuries or
damages to the product.
WATER
HEATER
SAFETY
WARNING
Under certain conditions hydrogen gas may be produced in a water heater that has not been
used for two weeks or more. Hydrogen gas can be explosive under these circumstances.
If the HOT water has not been used for two weeks or more, prevent the possibility of
damage or injury by turning on all Hot water faucets and allowing them to run for several
minutes. Do this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas is flammable, do not smoke or use an open flame or appliance during this process.
PROPER
INSTALLATION
CAUTION
• The base opening must not be obstructed by carpeting when the washing machine is installed
on a carpeted floor.
• Install or store where it will not be exposed to temperature below freezing or exposed to the
weather (Rain/Water Splash/ Direct Sunlight).
If the product is exposed to such conditions, electric shock, fire, break down or deformation may occur.
• Properly ground washer to confirm with all governing codes and ordinances. Follow details in
Installation Instructions.
If not grounded properly, break down and leakage of electricity may occur, which may cause electric
shock.
• Machine must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get damaged, possibly causing fire or
electric shock.
• Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
• Do not connect ground to a gas pipe.
It can cause explosion.
• Do not connect ground to telephone wires or lightning rods.
This may be dangerous during electrical storms.
• Washer shall be placed in dry areas specifically during rainy season.
Humid conditions may cause rusting which may result in product failure.
4
S afety Information
YOUR
LAUNDRY
AREA
WARNING
• Keep the area underneath and around your appliances free of combustible
materials such as lint, paper, rags, chemical, etc.
Operating with such materials around the machine may trigger explosion or
fire.
• Close supervision is necessary if this appliance is used by or near children.
Do not allow children to play on, with, or inside this or any other appliance.
There is potential danger that children might drown in the tub.
Do not touch the power plug with a wet hand.
It will cause electric shock
Do not put your hand, foot or anything under the washing machine
while the washing machine is in operation.
There is a rotating mechanism under the machine, so you could be injured.
WHEN USING
THE WASHER
CAUTION
• Use this appliance only for its intended purpose as described in this Owner’s Manual.
• Use this appliance only for Household Purpose .
• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s wash and care instructions.
• To minimize the possibility of electric shock, unplug this appliance from the power
supply or disconnect the washer at the household distribution panel by removing the
fuse or switching off the circuit breaker before attempting any maintenance or cleaning.
NOTE : Pressing Power button to turn off does NOT
disconnect the appliance from the power supply.
• Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded.
Flooded floors may induce electricity leakage, further resulting in electric shock or fire.
• If, during spinning, opening the lid does not stop the tub within about 15 seconds,
immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause injuries.
Never reach into the machine while it is running.
Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially
disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
Do not use water hotter than 60°C.
Use of excessively hot water may cause damage to fabrics or cause
leakage of water.
Ensure No water logging near or below washer to prevent rusting.
Rusting on certain parts may result in product failure
5
S afety Information
WHEN USING
THE WASHER
WARNING
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Do not use a plug socket and wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire , break down, and/or deformation
of parts.
Do not mix chlorine bleach with other household chemicals such as toilet cleaners,
rust removers, acids (such as vinegar) or product containing ammonia.
Mixing different chemicals can produce toxic gases which may cause death.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted
with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water.
Do not use or place these substances around your washer or dryer during operation.
It may ignite or explode.
Avoid electric heater, candle light, cigarette light, bug smoker, etc. near the machine.
It may ignite or deform the plastic part.
WHEN NOT
IN USE
CAUTION
• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage
if a break or rupture should occur. Check the condition of the fill hoses; they may need
replacement after 5years.
• When the air temperature is high and the water temperature is low, condensation may
occur and thus wet the floor.
• Wipe off dirt or dust on the contacts of the power plug.
Using unclean power plug may cause fire.
• Before discarding a washer, or removing it from service, remove the washer lid to
prevent children from hiding inside.
Children may be trapped and suffocated if the lid is left intact.
Do not attempt to repair or replace any part of this appliance unless
specifically recommended in this Owner’s Manual, or in published userrepair instructions that you understand and have the skills to carry out.
Operating the machine with improperly replaced parts may be a cause for fire or
electric shock.
Do not tamper with controls.
It may lead to electric shock, fire , break down, deformation.
Do not yank the power cord in an attempt to disconnect the power plug.
Securely hold the power plug to unplug the machine.
Failure to observe these instructions may cause electric shock or fire due to shortcircuit .
When you are cleaning the washing machine, do not apply water directly to
any part of the washing machine.
It will cause short circuit and electric shock.
6
I dentification of Parts
Body
POWDER
DETERGENT BOX
WATER SUPPLY
HOSE
Make sure the
water does not
leak.
MAGIC FILTER
Clean regularly to
stop linting on the
clothes load.
SOFTENER
INLET
en
t op
no
Do
BLEACH
DISPENSER
FUNCTION
SELECTOR
POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to
avoid a hazard.
TUB
JET SPRAY NOZZLE
Depending upon the Inlet
Water Pressure, performance
of Jet Spray may vary.
(Works in Normal, Turbo Wash,
Pre Wash+ Normal & Aqua
Reserve Wash Programs).
START/PAUSE
BUTTON
Use to start or
stop the washing
machine
temporarily.
CASTORS
Use for easy
translocation
(at rear bottom edge)
DRAIN HOSE
Keep the drain hose
flipped down while
washing is in progress.
ADJUSTABLE LEGS
Use to level the washing
machine for correct
balance & spin
operation.
BASE
Accessories
Water supply hose
Drain hose
Anti-rat cover
For Cold Water
Snap Ring
NOTE
“
” Parts can be different according to the model.
Please do not match this figure with model as it may be different from your model .These are schematic diagrams only.
Due to continuous improvements at LG, specification of washing machine are subject to change without prior notice.
7
Function Information
Our machine provides various washing methods which suits various conditions
and types of laundry.
Different types of laundry washing
Normal Wash
Use this Program for everyday washing e.g. sheets, towels, T-shirts. (refer to page 16)
Turbowash
Use this program to save time for washing regular laundry. (refer to page 16)
. follow Normal Wash Course pattern.)
(* Turbowash logic is applicable on water level 1 to 7, higher levels
Strong (Jeans) Wash
Use this Program for heavily soiled durable garments e.g. overalls, jeans.
Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed.(refer to page 16)
Pre Wash+ Normal Wash
Use as pre treatment to heavily soiled/ dirty cloths to get best wash performance. (refer to page 16)
Gentle (Wool/Saree)
Delicate clothes (lingerie, woolens, saree, etc.) which may be easily damaged can be washed. (refer to page 19)
The machine washable woolens or saree are specifically made to prevent damage during machine-washing.
Most hand-knitted garments are not machine washable, so recommend you to hand wash them.
• For the washing instruction, check the clothing label before wash.
• A neutral detergent is recommended for the woolens or saree.
• Do not use a tumble dryer to prevent damage.
• To avoid direct sunlight, cover up the clothes with towels during natural dry.
Some woolens or sweater may clog a drain hose by their lint, so recommend you to use spin only after hand-wash them.
Aqua Reserve Wash
Use this program to prevent automatic draining of water at the end of cycle.(refer to page 19)
Washing according to the condition of laundry
Quick Wash
Quick Wash can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to page 16)
Soak Wash
Soak Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove dirt and
grime. (refer to page 18)
Other washing method
Tub Clean
Use this program to clean the inside of washing machine especially Inner tub & Outer tub . (refer to page 20)
Delay Start Wash
Delay Start Wash is used to delay the finishing time of the operation.
The number of hours to be delayed can be set by the user accordingly. (refer to page 23)
Option Wash
When the user needs only SPIN, RINSE/SPIN,RINSE, WASH/RINSE, WASH, WASH/RINSE/SPIN.
(refer to page 21)
* Product feature may vary according to different models. Refer page 35 for modelwise
features for your purchased model.
8
Preparation Before Washing
Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it
should be washed.
Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.
Sorting
To get the best results, different fabrics need to be washed in different ways.
• SOIL (Heavy, Normal, Light)
Separate clothes according to th e type and amount of soil.
• COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
• LINT (Lint Producers, Collectors) Separate lint producers and lint collectors.
Lint Producers
Terry cloth, Towels, Nappies, Diapers
Synthetics, Socks
Lint Collectors
Check before Loading
• Check all pockets to make sure that they are emtpy. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.
• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
• Pretreat any dirt and stains.
• Make sure the clothes are washable in water.
• Check the washing instructions.
• Remove tissue from pockets.
WIRE
CAUTION
Do not wash or spin any item labeled or known to be water-proof or water-resistant, even if the product care label on the item
permits machine washing. Failure to follow these instructions could result in severe damage to your laundry, your washer and/or
property damage as a result of abnormal vibration of the washer.
- Examples of water-proof or water-resistant items include certain mattress pads, mattress covers, rain gear, camping gear, skiing
apparel, outdoor gear and similar items.
Pretreatment on stains or heavy soil
• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer.
Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
• Use a pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.
(For more detail refer to page13)
Loading
Do not wash fabrics containing flammable materials
(waxes, cleaning fluids, etc.)
Load Size
The WATER LEVEL should just cover the clothes.
Adjust the load size accordingly. Loosely load clothes
not higher than the top row of holes in the washer tub.
To add items after washer has started, press Start button
and submerge additional items. Close the lid and press
Start button again to restart.
WARNING
Fire Hazard
Never place items in the washer that are dampened with gasoline
or other flammable fluids. No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on it (including
cooking oils). Doing so can result in death, explosion, or fire.
Light and Large-sized clothing
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net* and
wash them in a small amount of water. If the laundry floats during the wash cycle, it may
become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
Long laundry items
Use nylon nets*for long, DELICATE items. For laundry with long strings or long length , a net will prevent
tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
* Nylon net is not supplied by LG.
9
U
se of Water, Detergent, Bleach and Softener
Using Water
Amount of WATER LEVEL
• This machine detects the quantity of laundry
automatically, then set the WATER LEVEL
• When you select a wash program, the WATER
LEVEL will be shown on the control panel.
• The following table shows the amount of water level.
• When the WATER LEVEL is automatically detected,
it may differ depending on the quantity of laundry
even though the same WATER LEVEL is indicated on the control panel.
NOTE
[Minimum water amount]
It depends on laundry load and washer mode. Or manually you can pour a certain amount water into tub directly to some
height. That's because if water level reaches to the some height sensed by washer itself, washer automatically operates. In
other words, it is needed to pour water to the point when washer start operating.
NOTE
If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown or orange
spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be necessary for severe cases.
• When washing in COLD water additional steps may be needed;
• Adjust Detergent amount and pre-dissolve Detergent in WARM water
• Pre-treat spot and stains
• Soak heavily soiled items
• Use appropriate bleach
* Temperature below 18°C... (65°F) will not activate laundry additives and may cause lint, residue, poor
cleaning etc.
In addition, Detergent manufactures and care labels is define COLD water as 26-29°C... (80-85°F).
If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and
clean effectively.
Using Detergent
Detergent
Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems.
Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.
Choosing the right Detergent
We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or granulated
soap powders should not be used in your washing machine. When washing woolens remember to use
Detergent suitable for washing woolens.
10
U
se of Water, Detergent, Bleach and Softener
Water Level and Amount of Detergent
l
Concentrated detergent: 20g per 30 liters of water.
l
Regular synthetic detergent: 30g per 30 liters of water.
l
When sensing water levels automatically, the amount of
detergent can differ according to the amount of laundry
even at the same water level.
. detergent, use one that generates less
For synthetic
.
bubbles. This type of detergent is specially designed
for washers
In case of using liquid detergent, dissolve it with water
(detergent: water=1:1) and deposit it through the bleach
deposit hole
The correct amount of detergent will vary depending
on the amount of soil in your clothes. (Jeans and work
clothes may need more detergent, while bath towels
usually need less.)
For liquid and concentrated detegants, follow the
recommondations of the detergent manufacturer.
l
l
l
l
Water
Level
Amount
of Water
Amount
of laundry
Water
Level
Amount
of Water
10
62 l
Less than
9
59 l
Less than 5.0 kg
8
51 l
7
10
85 l
Less than
9
80 l
Less than 6.0 kg
Less than 3.5 kg
8
68 l
Less than 5.3 kg
50 l
Less than 3.0 kg
7
66 l
Less than 4.6 kg
6
48 l
Less than 2.5 kg
6
62 l
Less than 3.9 kg
5
42 l
Less than 2.0 kg
5
52 l
Less than 3.2 kg
4
39 l
Less than 1.5 kg
4
49 l
Less than 2.5 kg
3
34 l
Less than 1.0 kg
3
42 l
Less than 1.8 kg
2
29 l
Less than 0.6 kg
2
34 l
Less than 1.1 kg
1
26 l
Less than 0.4 kg
1
32 l
Less than 0.5 kg
Applicable for all models
except T2309VSA* model
Amount
of laundry
Applicable for T2309VSA*
model only
**Rated Capacity of Model
*1,5,H,J,K,L,R,X,Y or etc.
Note : To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of
foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough
Detergent has been used, soil and lint can settle back on the clothes or the washing machine.
If excess Detergent is used, the rinse will not be efficient. Also, it could cause environmental
pollution, so use it accordingly.
pe
to
no
Do
Add measured detergent to the detergent compartment of the dispenser drawer.
We recommend the use of powdered detergent in the dispenser when using a
delay wash function.
Detergent is flushed through the dispenser at the beginning of the wash phase.
Detergent usage may need to be adjusted for water temperature, water hardness,
size and soil level of the load.
Avoid using too much detergent in your washer, as it can lead to oversudsing and
detergent residue being left on the clothes.
n
Adding the detergent
OR
Using Liquid Bleach
• Check clothing care label for special instructions and separate the
laundry to be bleached.
• Dilute liquid chlorine bleach.
• Measure the recommended amount of liquid bleach carefully
following instructions on the bottle.
• Before starting the washer, pour measured amount of bleach directly
into bleach dispenser. Avoid splashing or overfilling. Powdered
bleach should be mixed with water before pouring.
Bleach dispenser
NOTE
n Never pour undiluted liquid bleach directly onto clothes or into the wash basket.
This may cause change of color or damage the laundry.
n Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remove Mixing can release
a toxic gas which may cause death.
n Do not pour powdered bleach into bleach dispenser.
Part may vary according to model.
11
U se of Water, Detergent, Bleach and Softener
Using Fabric Softener
• Dilute fabric softener with water.
Undiluted fabric softener may result in spots that look like oil stains.
Softener dispenser(
)
• Measure and add the recommended amount of fabric softener into the
compartment marked with this symbol(
).
Follow manufacturer’s direction.
Fabric softener is automatically dispensed in the final rinse with
indication beep.
If you want extra rinse, you must add fabric softener manually
when indication beep rings in the final rinse.
This maximize the fabric softener function.
• Do not overfill. The dispenser hold max 35ml.
Never add more than 35ml.
Overfilling can cause early dispensing of the fabric softener which could result in stained clothes.
A cup with a pouring spout will help you avoid spilling.
• The effect of adding fabric softener may vary according to its viscosity. The stickier fabric softener makes
its effect the lower. For a sticky fabric softener it is recommended that it be diluted with water, then be
manually correct time to dispense manually is optionally applied to some models. Please keep it in mind that
fabric softener has to be diluted with water before dispensed and never poured directly on clothes.
•
•
•
•
Attention
Do not mix with detergent or bleach.
Never pour fabric softener directly on clothes. It may stain them.
Do not stop the washer during the first spin for timely dispensing.
Option washing is not designed to be used with fabric softener dispenser.
Scrud (Waxy Build up)
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener
comes into contact with Detergent. This build-up is not brought about by a fault in the machine.
If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant
smell in your washer.
If you wish to use fabric softener we recommend
• Using fabric softener sparingly.
• When filling the dispenser, do not splash or overfill.
• Clean dispenser as soon as the cycle is finished.
• Clean your machine regularly. (refer to page 20 or 29)
• Cold water washing increases the chance of this build-up occurring. We recommend a regular WARM or
HOT wash e.g. every 5th wash should be at least a warm one.
• Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a
build-up.
12
S pecial Guide for Stain Removal
WARNING
Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or
products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
Read and comply with all instructions on stain removal products.
Keep stain removal products in their original labeled containers and out of children's reach
Thoroughly wash any utensil used.
Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry
cleaning solvents or other flammable or explosive substances because they give off vapors that could ignite or explode.
Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
Stain Removal
STAIN
Adhesive tape, chewing gum,
rubber cement
Baby formula, dairy products, egg
Beverages (coffee, tea, soda, juice,
alcoholic beverages)
Blood
Candle wax, crayon
Chocolate
TREATMENT
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover
or nonflammable dry cleaning fluid.
Use product containing enzymes to pretreat or soak stains.
Pretreat stain. Wash using COLD water and bleach safe for fabric.
Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using
bleach safe for fabric.
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Collar or cuff soil, cosmetics
Pretreat with prewash stain remover or rub with bar soap.
Dye transfer on white fabric
Use packaged color remover. Wash using bleach safe for fabric.
Grass
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Grease, oil, tar (butter, fats, salad
dressing, cooking oils, car grease,
motor oils)
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
using hottest water safe for fabric.
Ink
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Mildew, scorch
Wash with chlorine bleach if safe for fabric, or soak in oxygen bleach and HOT water before washing. Badly
mildewed fabrics may be permanently damaged.
Mud
Brush off dry mud. Pretreat or soak with product containing enzymes.
Mustard, tomato
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Nail polish
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
Paint, varnish
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed.
OIL BASED & VARNISH : Use solvent recommended on can label. Rinse thoroughly before washing.
Rust, brown or yellow
discoloration
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
Shoe polish
LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach
safe for fabric.
For successful stain removal:
• Remove stains promptly.
• Determine the kind of stain, then follow the recommended treatment in the stain removal
chart below.
• To pretreat stains, use a prewash product, liquid Detergent, or a paste made from granular
Detergent and water.
• Use COLD water on unknown stains because HOT water can set stains.
• Check care label instructions for treatments to avoid on specific fabrics.
• Check for color fastness by testing stain remover on an inside seam.
• Rinse and wash items after stain removal.
13
Follow fabric care label
instructions
#
Beeper Button
If you want to use the
washing machine without
alarm signal sounds,
pressing Beeper button
allow you to select :
High Off
Low
High respectively.
Default setting is High
10
Soil Level
Use this feature based
on soil/dirt level of the
cloth. Select Soil Level
for low, medium or high
soil/dirt level
respectively.
• This feature cannot be
Selected for courses :
Tub Clean, Wool, Air Dry
& Turbo Wash.
• This feature cannot be
selected when only spin
option is selected.
Air dry selections light up by Press & hold
Spin for 3 Sec.
Press Power button to deselect.
To lock, press & hold Rinse key
for 3 sec. To unlock, press & hold
Rinse key one more time for 3 sec.
(refer to page 24)
When the button is pressed
during washing, total remaining
cycle time is displayed.
#
#
Do not press any three or four buttons simultaneously, it may cause malfunctioning.
Do not match above picture with your purchased model, the Control Panel may differ according to different models.
Product feature may very according to different models. Refer page 35 for modelwise features for your purchase model.
14
SMART DIAGNOSISTM
Function Display
It marks the place to put the phone
to receive signal when a problem
occurs. (refer to page 34)
15
To cancel delay time, turn the power
switch off or press Start/Pause button
& then keep pressing delay button
until Delay LED turn Off.
(refer to page 23)
follows :
Program 1:
Normal ► Turbowash ►Quick Wash
►Strong ►Normal
Program 2:
Prewash+ Normal ► Aqua Reserve ► Gentle
(Wool / Saree) ► Tub Clean ► Prewash+ Normal
15
Normal Wash
1
2
Use this program for washing
normal clothes, this mode
automatically selects the most
appropriate conditions and
completes the sequence in one
operation. The built-in sensor
detects the size of the load and
ideal wash power & wash, rinse
and spin times are set
accordingly.
Turbo Wash
3
Normal
program is
set by default
1
2
Use this program to save Time
with efficient Water & Energy
consumption.
3
4
Select Turbo
Wash program
on the Control
Panel
1
2
3
5
Select Quick
Wash program on
the Control Panel
STRONG
(JEANS)
1
2
Spread the
jeans evenly
in the tub
3
4
Select Strong
(Jeans) program
on the Control
Panel
+
Pre Wash
Normal
1
• Use as pre treatment to wash
heavily soiled, shirt neck collar
& sleeves, kids soccer / sports
wear.
2
3
Select PreWash+
Normal program
on the Control
Panel
• 8 minutes of unique pre washing
operation will be performed before
main wash.
Wash (2min) ▶Soak (2min)▶
Wash (2min) ▶Soak (2min)
* Product feature may vary according to different models. Refer page 35 for modelwise
features for your purchased model.
16
4
4
Wash tub rotates twice to
detect the laundry load.
Water level will be indicated
and water will be supplied
5
Wash tub rotates twice to
detect the laundry load.
Water level will be indicated
and water will be supplied
6
5
Open the lid and add
appropriate quantity of
detergent as shown on water
level indicator or follow the
Detergent manufacturer's
instructions
Close the lid
Wash tub rotates twice to
detect the laundry load.
Water level will be indicated
and water will be supplied
5
Wash tub rotates twice to
detect the laundry load.
Water level will be indicated
and water will be supplied
When the wash program
ends, the buzzer will ring
and the power goes off
automatically after
15 secs.
6
Open the lid and add
appropriate quantity of
detergent as shown on water
level indicator or follow the
Detergent manufacturer's
instructions
Close the lid
7
When the wash program
ends, the buzzer will ring
and the power goes off
automatically after
15 secs.
4
Add appropriate quantity of
detergent as shown on water
level indicator or follow the
Detergent manufacturer's
instructions
5
6
7
When the wash program
ends, the buzzer will ring
and the power goes off
automatically after
15 secs.
6
Open the lid and add
appropriate quantity of
detergent as shown on
water level indicator or follow
the Detergent manufacturer's
instructions
Close the lid
- Changes to WATER LEVEL is possible,
only after pressing START/PAUSE button
during operation.
(refer to page 14)
- An innovative Wash program which
delivers results similar to normal Course
with saving time significantly and
consuming less Water and Energy.
- For optimum Turbo wash performance
we recommend to use 1 to 7 water Level
with default selections
When Static pressure of water is more
than 2kg/cm2, the QUICK WASH course
time will be
• 22min : Models 8kg or less
• 27min : Models 9kg or above
7
When the wash program
ends, the buzzer will ring
and the power goes off
automatically after
15 secs.
6
Open the lid and add
appropriate quantity of
detergent as shown on water
level indicator or follow the
Detergent manufacturer's
instructions
Close the lid
- If the water is already in the tub, or putting
wet laundry into the tub before starting will
increase the WATER LEVEL.
7
When the wash program
ends, the buzzer will ring
and the power goes off
automatically after
15 secs.
17
- If the water is already in the tub, or putting
wet laundry into the tub before starting
will increase the WATER LEVEL.
- Changes to WATER LEVEL is possible,
only after pressing START/PAUSE
button during operation.
(refer to page 14)
Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty.
SOAK mode can be used with NORMAL or STRONG (JEANS) or AQUA RESERVE WASH
program.
SOAK will not work in GENTLE(WOOL/SAREE),
+
PREWASH NORMAL , QUICK WASH &
TURBO WASH Programs.
Segment display total cycle time.
For e.g. After wash selection of 25 minutes, each consecutive
wash button press, sets soak wash for 15, 25, 35 minutes
respectively.
When the wash program ends, the buzzer will ring and the
power goes off automatically after 15 secs.
Select soaking time 15minutes, 25minutes, or 35minutes (excluding washing time) by pressing
the Wash button repeatedly.
* Starting time in Order of Soak-Wash timing may vary model to model
18
G
entle (WOOL/SAREE)
Use this program for washing delicate fabrics such as lingerie, woolens and saree (wash only
“water washable” clothes.
Before washing your woolens or saree check the care label for the washing instructions.
Select the PROGRAM button to select Gentle (WOOL/SAREE) program
Add the laundry into the washing tub.
5
Use neutral detergent appropriate for the laundry. When washing woolens or saree
use a mild detergent recommended for washing wool or saree.
• When setting the Water Level manually, do not set to Medium to prevent damage to laundry. It should always be high.
• Washing with Hot water may damage the laundry. For load under 2Kg use cold water.
• In order to avoid damage to laundry, the spin cycle may appear slow. This also avoids wrinkles and clothing may still
contain some water. This is normal.
A QUA RESERVE Wash
Use this program to reuse the water for second round of wash load
AQUA RESERVE
Do not keep water hold for long time after the end of cycle
This may cause bad odour and damage the laundry.
SPIN function cannot be done in AQUA RESERVE wash program.
19
This program takes about 2hrs to be completed.
irritant odour.
damage to the tub.
time, as it may rust the tub.
Use this program once in every month.
20
Press the POWER button to turn power on.
Press Spin for 3 seconds to select Air Dry.
Other function cannot be selected during Air Dry.
Automatically set to 30 minutes upon selection.
Press Spin button again to select duration. (30min
To deselect Air Dry press power button.
1hr
1:30hr
2hr)
Press the START/PAUSE button.
When the wash program ends, the buzzer will ring
and the Power goes off automatically after 15 secs.
When you select Air Dry for more than 1 hour
1) You can reduce the drying time by minimzing the moisture in the laundry.
2) Always keep the laundry amount to 2kg or less and make sure to spread it out evenly.
3) Select 1 hour for cotton laundry and 2 hours for synthetic fiber laundry for
effective Moisture removal.
When you only need the SPIN, RINSE/SPIN,RINSE, WASH/RINSE, WASH, WASH/
RINSE/SPIN these can be set manually.
• Press the WASH button to
select the desired timing.
• Press the RINSE button to
select the desired no. of
rinse cycles.
• Press the RINSE button till
No Rinse Selection (Rinse • Press the SPIN button till
Lamp off).
No Spin Selection (Spin
Lamp off).
• Press the SPIN button till
No Spin Selection (Spin
Lamp off).
21
• Press the SPIN button to
select the desired time of
spin.
• Press the WASH button to
select the desired timing.
• Press the RINSE button to
select the desired no. of
rinse cycles.
• Press the RINSE button to
select the desired no. of
rinse cycles.
• Press the SPIN button to
select the desired time of
spin.
• Press the SPIN button till
No Spin Selection (Spin
Lamp off).
When you want to only
drain, press SPIN button.
Then press START/PAUSE
button.
Wait until the water in the
washing tub drains completely
and then press POWER button
to finish the activity.
Press the WATER LEVEL button, to control the water level according to the
amount of laundry. If you do not specify the water level, then it will be
automatically selected, only after load detection. (Not applicable for only spin
process).
(Add detergent only where wash cycle is selected)
When a RINSE, WASH/RINSE, WASH option is selected, after the wash is completed the water will not be drained
off. If you wish to drain the water, press SPIN button after that press the START/PAUSE button and wait until the
water in the tub has drained completely.
22
DELAY START (RESERVATION) Wash is used to delay the finishing time of the operation. The hours to be
delayed can be set by the user accordingly. The time on the display is the finishing time, not the start time.
Select the program for laundry on the Control panel.
This program will not work in GENTLE (WOOL/SAREE)
and TUB CLEAN Program.
Press Time Delay (Reservation) button to set reservation time.
If reservation button is pressed, it will turn on reservation lamp and show up 3:00.
ex) It is 1:00 PM and if you want to finish laundry by 7:00 PM
Keep press reservation button to set desired laundry ending time.
(7:00-1:00=6hours)
Reservation can be made up to 3~18 hours.
For 3~12 hours, reservation can be set in 1 hour interval
For 12~18 hours, reservation can be set in 2 hour interval.
Less than 3 hour is cannot be reserved.
Finishing time can be delayed from 3~18 hours. Delaying from 3~12 hours can be done in 1 hour time intervals
and from 12~18 hours in 2 hour time intervals.
wash program manually, press the
23
Press and hold Rinse Button for 3 seconds.
• The child lock is set, it will not be released
automatically even if the cycle is terminated.
• Thus, you should turn power on washing machine
and then terminate the function by pressing "Rinse”
button for 3 seconds.
How to Unlock
If you want to unlock, press & hold the Rinse Button for 3 seconds again.
the remaining time are alternatively shown on the display while they are locked.
Power On/Off button can operate while Child Lock function is activated.
24
lacing, Leveling and Installation
Improper installation of the washer may cause noise and malfunctioning.
Note : 1. The ventilating openings in the base area must not be obstructed by carpeting when the washing machine is
installed on a carpeted floor.
2. Install the washing machine on a level and firm
Installation area
surface.
1
How to adjust leveling
Install the washer on flat and firm surface.
2
Checking level
The Basement is not flat, fill the water just touching the
Pulsator and see uniform distribution. If not, adjust the
legs as shown in the figure.
Adjustable leg
Turn the adjustable legs to set the washer
horizontal (Both the front legs).
Top View
H Don't add anything under back side legs.
Distance between drain hose and the wall
3
Distance between drain hose and the wall should be more
than 10cm, and the distance between the other part or the
rear part and the wall should be more than 2 cm.
.
Checking Proper placement
More than 10cm
More than 2cm
More than 2cm
Anti-rat cover installation
Press the corners of the machine diagonally
as shown in the figure, If any movement is observed,
adjust the legs for proper leveling.
# Moving of the Machine
Casters are provided for easy translocation of your machine
* Grip the machines properly as shown in fig.
* Tilt the machine towards your side at a angle
O
O
45 ~ 55 .
Insert the Anti rat cover firmly from back side
side of washing machine.
Casters
Note : * Be careful that you should not drop the machine.
* Never move the machine on casters when there is load inside.
# Product feature may vary according to different models. Refer page 35 for modelwise features for your purchased model.
# Please do not match the figures with model as it may be different from your model. These are schematic diagrams only.
25
C
onnecting Hose
Water Supply Hose
Normal Type
1
(Normal tap without thread & one touch type inlet hose.)
Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose.
Middle
connector
Fixed Sticker
Pressing Handle
Pressing Rod
Water Supply Hose
2
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the
tap can be placed in the middle.
Rubber packing
screw
Fixed sticker
NOTE
In case tap is too large.
Guide plate
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
plate. Then follow step1.
3
Rubber packing
Fixing Connectors to the Tap
Connector
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws
.
4
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
5
Connector
Middle
Connector
Fixed sticker
Connecting Middle Connector and Water Supply Hose
Press down the pressing rod of the Water Supply
Hose which was separated from middle connector
(refer to Step1) and then join it to the middle
connector.
Pressing rod
Water Supply Hose
6
Connector
Middle
Connector
Check for water leakage
After connecting the other end of hose to machine open the tap to
check for any water leakage.
If the connection leaks, close the tap and start
again from step 1.
If you skip step 1, water leakage may occur.
26
Pressing handle
condition.
Drain Hose
How to connect the drain hose
1
Insert the drain hose to the connecting area at the body.
2
1. Press the hose clip.
2. While pressing, push the hose towards
the body.
3. Release the hose clip after pushing the
hose.
Less than 2m
Less than 6cm
The hose is placed
over a doorsill.
The hose is clogged by
alien substances.
Less than 10cm
Make sure that the hose is
not crushed between the
wall and the washer
Make sure that the
hose is not crushed.
Avoid submerging
the end of hose.
Less than 3m
Extension hose is
used.
27
G rounding Method
Earth wire should be connected.
If the earth wire is not connected, there is possible a danger of electric shock caused
by the current leakage .
Grounding Method with Ground insert space Terminal
If the AC current outlet has a ground terminal, then
separate grounding is not required.
Ground terminal
Grounding is
not needed
CAUTION
Concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords,
or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect
the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon.
Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance
Other Grounding Method
Burying Copper Plate
Connect the Ground Wire to a Ground Copper
Plate and bury it more than 75cm in the ground.
Ground Wire
75cm
Ground Copper Plate
Using Ground Wire
Ground
Wire
Connect the ground Wire to the socket provided
exclusively for Grounding.
Using a Short Circuit Breaker
If grounding methods described above are not possible,
a separate circuit breaker should be employed and
installed by a qualified electrician.
28
Short-circuit
breaker
To Clean the Filter in the Inlet Valve #
After Stopping the water supply,
Remove inlet hose connected
to the machine and pull out
the filter as shown.
IDE)
KS
(BAC
To Clean the Magic Filter
If the magic filter is damaged, purchase a new one from LG Authorised Service Center.
# Product feature may vary according to different models. Refer page 35 for model wise features for your
purchased model.
# Please do not match the figures with model as it may be different from your model. These are schematic
diagrams only.
29
When there is a fear of freezing
• Close the water taps and remove the Water Supply Hose.
• Remove the water which remains in the water supply.
• Lower the drain hose and drain the water in the bowl and the drain hose by spinning.
If frozen
• Remove the water supply hose, and immerse it in HOT water at approx.. 40°C.
• Pour approx. 2 liters of HOT water at approx. 40 °C, into the bowl and let it stand for 10 minutes.
• Connect the water supply hose to the water tap and confirm that the washing machine performs the
supply and drainage of water.
Wash Inner-tub
Leave the lid open after washing to allow moisture to evaporate. If you want to clean
the inner-tub use a clean soft cloth dampened with liquid Detergent, then rinse. (Do
not use harsh or gritty cleaners.)
Inlet Hoses
Hoses connecting washer to faucet should be replaced every 5 years.
Exterior
Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with
sharp objects.
Long Vacations
Be sure water supply is shut off at faucets. Drain all water from hoses if weather will
be below freezing.
Cleaning the Inside of your Washer
If you use fabric softener or do regular COLD water washing, it is very important that you occasionally clean the
inside of your washer.
• Fill your washer with HOT water.
• Add about two cups of a powdered Detergent that contains phosphate.
• Let it operate for several minutes.
• Stop the washer, open the lid and leave it to soak overnight.
• After soaking, drain the washer and run it through a normal cycle.
Or use TUB CLEAN PROGRAM periodically.
We do not recommend that you wash clothes during this procedure.
Products that might damage your washing machine
• Concentrated bleaches and diaper sanitizer will cause damage to the paintwork and components of your washer.
• Hydrocarbon solvents i.e. petrol, paint thinners and lacquer thinners, etc. can dissolve plastic and blister paint
(Be careful when washing garments stained with these solvents as they are flammable DO NOT put them in
washer or dryer.)
• Some pretreatment sprays or liquids can damage your washer’s control panel.
• Use of dyes in your washer may cause staining of the plastic components. The dye will not damage the machine
but we suggest you thoroughly clean your washer afterwards. We do not recommend the use of dye strippers in
your washer.
• Do not use your washer lid as a work surface.
30
S mart Closing Door*
• Washing process can be seen inside the tub through tempered safety glass.
• Smart hinge prevents sudden closing of the door.
• Door is heavy, be careful while closing of the door. Do not let your hands or any other material
to caught below door. It might cause injury or damage.
Smart Hinge
Smart Hinge
*
- Door closing time is dependent on ambient temperature.
- Higher the ambient temperature, lower the door closing time and vice versa.
- Smart Closing Door performs best when lid is closed from full open condition.
31
C ommon washing problems
Many washing problems involve poor soil & stain removal, residues of lint and scum, and
fabric damage. For satisfactory washing results, follow these instructions.
WASH PROBLEM
Problems
Solutions & Preventive Measures
Possible Causes
Poor soil
removal
• Not enough Detergent
• Wash Water Temperature
too low.
• Overloading the washer
• Incorrect wash cycle
• Incorrect sorting
• Pretreat stain not done
• Use correct amount of Detergent for load size, amount of
soil and water hardness.
• Use WARM or HOT water for normal soil.
Different Water Temperature may be required according to
soil type. (refer to page 10)
• Reduce load size.
• Wash with STRONG (JEANS) or SOAK & STRONG
(JEANS) wash cycle for heavy soiled laundry.
• Separate heavily soiled items from lightly soiled ones.
• Pretreat stain and heavy soil according to directions shown
on page 9.
Blue Stains
• Undiluted fabric softener
dispensed directly onto
fabric
• Rub the stain with bar soap.
• Do not overfill fabric softener dispenser and do not pour
liquid fabric softener directly onto fabric.
See page 12 for more instructions.
Black or gray
marks on
clothes
• A buildup caused by the
interaction of fabric softener
and Detergent can flake off
and mark clothes
• Not enough Detergent
Yellow or
brown rust
stains
• Iron or manganese in
water supply, water pipes,
or water heater
• To restore discolored load of whites, use rust remover safe
for fabric.
• Install nonprecipitating water softener or an iron filter in
your water supply system for an ongoing problem.
• Before washing, run water for a few minutes to clear lines.
Lint
• Incorrect sorting
• Tissues left in pocket
• Overloading the washer
• Wash lint givers eg. towels, flannelette sheets, eparately
from lint collectors eg. synthetic fabrics and remove tissues
in pockets before wash. See page 9 for sorting and caring
before loading.
• Do not overload the washer
Residue or
Detergent
• Overloading the washer
• Undissolved Detergent
• Use too much Detergent
• Do not overload the washer.
• Some Detergents need to be pre-dissolved, check the Detergent
instructions. Try pre-dissolving the Detergent.
• Increase Water Temperature using HOT water safe for fabric.
• Use proper amount of Detergent.
Holes, tears,
or snags
• Incorrect use of chlorine
bleach.
• Unfastened zippers,
hooks, buckles
• Ribs, tears and broken
threads
• Overloading the washer
• Degradation of fabric
• Never pour chlorine bleach directly on fabric.
See page 11 for adding liquid bleach.
• Fasten zippers, hooks, and buckles.
• Remove objects in pockets. See page 9 for caring before
loading.
• Do not overload the washer.
• Keep the recommendations against Scrud(waxy buildup).
(refer to scrud page12.)
• Use correct amount of Detergent for load size, amount of soil
and water hardness.
32
T roubleshooting
Self-diagnostic error mode
The machine will display and playback the error messages if there is any error in machine
for your suitable action.
Symptom
Error Display
Checkup
• Is the water tap shut off?
• Is the water supply cut off ?
• Is the tap or water supply hose frozen ?
Water Supply
Failure
• Is the water pressure low or is the filter
of the inlet valve clogged with
impurities?
• Is the Hot hose connected to cold?
• Is the Cold hose connected to hot?
• Is the drain hose positioned correctly?
• Is the drain hose bent or placed too high?
• Is the internal part of the hose or drain
pump (only pump model) clogged with
impurities?
• Check if electric power has gone off ?
Drainage Failure
• Is the laundry evenly balanced?
Spin Failure
• Is the washing machine placed on a flat
surface.?
Door(Lid) Open
• Is the lid closed?
Internal sensing
failure
• Please call your nearest LG Electronics
service center for help.
Power failure
Motor Error
Overflow failure
• Once Child Lock is applied, it will not deactivate
automatically after Power Turn Off and again Turn
On. To deactivate Child Lock, Press & Hold Rinse
key for 3 Sec.
Child Lock
33
S
mart DiagnosisTM
*
Only use this feature when instructed to do so by the LG Customer Service Call Center. The transmission
sound is similar to a fax machine, and so has no meaning except to the call center.
Press and hold the Water level button for three seconds, while holding the phone
mouthpiece to the icon or POWER button.
* Product feature may vary according to different models. Refer page 35 for modelwise features for your
purchased model.
34
Feature and Specificaion
T2165VSA*
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Cold
Cold
Cold
Cold
Cold
Cold
10
10
10
10
10
10
-
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
40
32
32
32
32
32
D
H
590 x 606 x 960
540 x 540 x 910
Water
Gentle Weight Dimension
Aqua Turbo Delay Quick Strong Tub Soak Soil
Level Castors
Reserve Wash
Wash (Jeans) Clean Wash Level (Wool/Saree) (Kg) (W X D X H) mm
Selection
T2107VSA*
√
√
Inlet Water
Temperature
(Option)
T2175VSA*
√
Pre
Air Child Smart
+
TM
Normal Wash Dry
Lock Diagnosis
Normal
T2108VSA*
√
Model
T2185VSA*
W
T2309VSA*
Water Tap Pressure should be between 30 -800 kPa (0.3 - 8.0 kgf/cm2)
35
* : 1,5,H,J,K,L,R,X,Y or etc.
Features & Specifications
MFL68465615
Download PDF