LG | T7001TDDLC | LG T7001TDDLC Owner’s Manual

WASHING
MACHINE
T70CSA13P
T7001TDDLC
P/NO : MFL68465602
Rev. No.: 00
C
ontents
Read this manual
Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little
preventive care on your part can save you a great deal of time and money over the life of your washer.
You will find many answers to common problems in the Troubleshooting section. If you review our
chart of Troubleshooting Tips first, you may not need to call for service at all.
Page No.
Introduction
Installation
Product Features
3
Safety Information
Identification of Parts
4
7
Placing, Leveling and Installation
8
Connecting Water Supply Hose
Connecting Drain Hose
Before Starting to Wash
9
10
Preparation Before Washing
11
Use of Water, Detergent, Bleach and Softener 12
Special guide for Stain removal
15
Function of each Button
16
Washing Programs
Turbo Wash
Other Option
18
18
Additional Features
Function Options
20
Care and Maintenance
Cleaning and Maintenance
Grounding Method
21
23
Troubleshooting
Common washing problems
Troubleshooting
24
25
Specification
Specification
26
2
P
roduct Features
Washer doesn't operate while the lid is open. If the lid is open during the wash,
rinse or spin cycles, the operation stops for safety.
Fuzzy Logic Control
A built-in load sensor automatically detects and measures the laundry load and
a microprocessor optimizes washing conditions such as ideal water level,
washing time and optimum detergent quantity indication.
Advanced technology is built into the Electronic Control System which ensures
the best washing result.
START
SENSING SETTING
Laundry Sensor Optimum
Water Level
Washing
Sensor
Condition
WASHING
AUTO
POWER
OFF
TurboDrum washing
When "Punch + 3" washing wings turn, the washing tub turns in the
opposite direction. This makes the both sides current of water which
improve washing-performance by rubbing clothes strongly.
3 Step washing
3 step washing makes best washing performance with low tangling.
Rubbing
Rubbing and
Shaking
Shaking and
Disentangling
Auto Restart
In the event of a power failure, the washing machine will automatically start its
cycle from the point of interruption when power is resumed.
Magic / Lint Filter *
Lint and loose threads from laundry generated during the
washing cycle are caught by the magic / Lint filter for a
cleaner wash.
Note : Be sure to remove the machine from all packing base,
otherwise the machine will not be able to operate properly.
* Parts can be different according to the model.
3
S
afety Information
Read carefully and thoroughly go through this booklet as it contains important safety information
that will protect the user from unexpected dangers and prevent potential damages to the product.
This booklet is divided into 2 parts : Warning and Caution.
: This is a warning sign specifying user’s applications which might
be dangerous.
: This is a sign specifying ‘Strictly Forbidden’ applications.
WARNING
: Failure to comply with the instructions under this
sign may result in major physical injuries or death.
CAUTION
: Failure to comply with the instructions under this
sign may result in minor physical injuries or
damages to the product.
WATER
HEATER
SAFETY
PROPER
INSTALLATION
WARNING
Under certain conditions hydrogen gas may be produced in a water heater that has not been
used for two weeks or more. Hydrogen gas can be explosive under these circumstances.
If the HOT water has not been used for two weeks or more, prevent the possibility of
damage or injury by turning on all Hot water faucets and allowing them to run for several
minutes. Do this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas is flammable, do not smoke or use an open flame or appliance during this process.
CAUTION
• The base opening must not be obstructed by carpeting when the washing machine is installed
on a carpeted floor.
• Install or store where it will not be exposed to temperatures below freezing or exposed to the
weather (Rain / Water Splash).
If the product is exposed to such conditions, electric stock, fire, break down or deformation may occur.
• Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.
If not grounded properly, break down and leakage of electricity may occur, which may cause electric
shock.
• Machine must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get damaged, possibly causing fire or
electric shock.
• Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
• Do not connect ground to a gas pipe.
It can cause explosion.
• Do not connect ground to telephone wires or lightning rods.
This may be dangerous during electrical storms.
• Washer shall be placed in dry areas specifically during rainy season.
Humid conditions may cause rusting which may result in product failure.
4
S afety Information
YOUR
LAUNDRY
AREA
WARNING
• Keep the area underneath and around your appliances free of combustible
materials such as lint, paper, rags, chemical etc.
Operating with such materials around the machine may trigger explosion or
fire.
• Close supervision is necessary if this appliance is used by or near children.
Do not allow children to play on, with or inside this or any other appliance.
There is potential danger that children might drown in the tub.
Do not touch the power plug with a wet hand.
It will cause electric shock
Do not put your hand, foot or anything under the washing machine
while the washing machine is in operation.
There is a rotating mechanism under the machine, so you could be injured.
WHEN USING
THE WASHER
CAUTION
• Use this appliance only for its intended purpose as described in this Owner’s Manual.
• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s wash and care instructions.
• To minimize the possibility of electric shock, unplug this appliance from the power
supply or disconnect the washer at the household distribution panel by removing the
fuse or switching off the circuit breaker before attempting any maintenance or cleaning.
NOTE : Pressing Power button to turn off does NOT
disconnect the appliance from the power supply.
• Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded.
Flooded floors may induce electricity leakage, further resulting in electric shock or fire.
• If, during spinning, opening the lid does not stop the tub within about 15 seconds,
immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause injuries.
Never reach into the machine while it is running.
Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially
disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
Do not use water hotter than 60°C.
Use of excessively hot water may cause damage to fabrics or cause leakage of water.
Ensure No water logging near or below washer to prevent rusting.
Rusting on certain parts may result in product failure
5
S afety Information
WHEN USING
THE WASHER
WARNING
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Do not use a plug socket and wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire , break down, and/or deformation
of parts.
Do not mix chlorine bleach with other household chemicals such as toilet cleaners,
rust removers, acids (such as vinegar) or product containing ammonia.
Mixing different chemicals can produce toxic gases which may cause death.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted
with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water.
Do not use or place these substances around your washer or dryer during operation.
It may ignite or explode.
Avoid electric heater, candle light, cigarette light, bug smoker, etc. near the machine.
It may ignite or deform the plastic part.
WHEN NOT
IN USE
CAUTION
• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage
if a break or rupture should occur. Check the condition of the fill hoses; they may need
replacement after 5years.
• When the air temperature is high and the water temperature is low, condensation may
occur and thus wet the floor.
• Wipe off dirt or dust on the contacts of the power plug.
Using unclean power plug may cause fire.
• Before discarding a washer, or removing it from service, remove the washer lid to
prevent children from hiding inside.
Children may be trapped and suffocated if the lid is left intact.
Do not attempt to repair or replace any part of this appliance unless
specifically recommended in this Owner’s Manual, or in published userrepair instructions that you understand and have the skills to carry out.
Operating the machine with improperly replaced parts may be a cause for fire or
electric shock.
Do not tamper with controls.
It may lead to electric shock, fire , break down, deformation.
Do not yank the power cord in an attempt to disconnect the power plug.
Securely hold the power plug to unplug the machine.
Failure to observe these instructions may cause electric shock or fire due to shortcircuit .
When you are cleaning the washing machine, do not apply water directly to
any part of the washing machine.
It will cause short circuit and electric shock.
6
I
dentification of Parts
Body
POWDER DETERGENT
BOX
* WATER SUPPLY
HOSE
Make sure the water
does not leak.
SOFTENER INLET
Softener will automatically
flow into the tub.
*POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer
or its service agents
or similarly qualified
person in order to
avoid a hazard.
BLEACH
DISPENSER
FUNCTION SELECTOR
TUB
*MAGIC FILTER/LINT FILTER
Clean regularly to stop
linting on the clothes
load.
* START/PAUSE
BUTTON
Use to start or stop the
washing machine
temporarily.
DRAIN HOSE
ADJUSTABLE LEGS
Keep the drain hose
flipped down while
washing is in process.
Use to level the washing
machine for correct balance
& spin operation.
*BASE
Accessories
Water supply hoses
*Anti-rat cover
Drain hose
Snap Ring
Note
"*" Parts can be different according to the model.
Introduction
7
*Lint Filter
P
lacing, Leveling and Installation
Improper installation of the washer may cause noise and malfunctioning.
Note : 1. The ventilating openings in the base area must not be obstructed by carpeting when the washing machine is
installed on a carpeted floor.
2. Install the washing machine on a level and firm
Installation area
surface.
1
Install the washer on flat and firm surface.
How to adjust leveling
2
Checking level
The Basement is not flat, fill the water just touching the
Pulsator and see uniform distribution. If not, adjust the
legs as shown in the figure.
Adjustable leg
Turn the adjustable legs to set the washer
horizontal (Both the front legs).
Top View
H Don't add anything under back side legs.
3
Distance between drain hose and the wall
Distance between drain hose and the wall should be more
than 10cm, and the distance between the other part and
the wall should be more than 2 cm.
Checking Proper placement
More than 10cm
More than 2cm
More than 2cm
Press the corners of the machine diagonally
as shown in the figure, if any movement is observed,
adjust the legs for proper leveling.
Anti-rat cover installation
* Insert the anti rat cover firmly from back side of washing machine.
Low Base
Middle Base
FIXING POSITION
Screws
Anti Rat Cover
Adjustable Leg
* Parts can be different according to the model.
8
Installation
C
onnecting Water Supply Hose
Normal Type
1
(Normal tap without thread & one touch type inlet hose.)
Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose.
Middle
connector
Fixed Sticker
Pressing Handle
Pressing Rod
Water Supply Hose
2
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the
tap can be placed in the middle.
Rubber packing
screw
Fixed sticker
NOTE
In case tap is too large.
Guide plate
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
plate. Then follow step1.
3
Rubber packing
Fixing Connectors to the Tap
Connector
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
4
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
5
Connector
Middle
Connector
Fixed sticker
Connecting Middle Connector and Water Supply Hose
Press down the pressing rod of the Water Supply
Hose which was separated from middle connector
(refer to Step1) and then join it to the middle
connector.
Pressing rod
Water Supply Hose
6
Connector
Middle
Connector
Check for water leakage
After connecting the hose, open the tap to check
for any water leakage.
If the connection leaks, close the tap and start
again from step 1.
If you skip step 1, water leakage may occur.
Installation
9
Pressing handle
condition.
Drain Hose
How to connect the drain hose
1
Insert the drain hose to the connecting area at the body.
2
1. Press the hose clip.
2. While pressing, push the hose towards
the body.
3. Release the hose clip after pushing the
hose.
Less than 2m
Less than 6cm
The hose is placed
over a doorsill.
The hose is clogged by
alien substances.
Less than 10cm
Make sure that the hose is
not crushed between the
wall and the washer
Make sure that the
hose is not crushed.
Avoid submerging
the end of hose.
Less than 3m
Extension hose is
used.
10
Installation
Preparation Before Washing
Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your garment
and how it should be washed.
Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.
Sorting
To get the best results, different fabrics need to be washed in different ways.
• SOIL (Heavy, Normal, Light)
Separate clothes according to th e type and amount of soil.
• COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
• LINT (Lint Producers, Collectors) Separate lint producers and lint collectors.
Lint Producers
Lint Collectors
Terry cloth, Chenille Towels, Nappies, Diapers
Synthetics, Corduroy, Permanent Press, Socks
Check before Loading
• Check all pockets to make sure that they are emtpy. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.
• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
• Pretreat any dirt and stains.
• Make sure the clothes are washable in water.
• Check the washing instructions.
• Remove tissue from pockets.
WIRE
Pretreatment on stains or heavy soil
• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer.
Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
• Use a pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.
(For more detail refer to page15)
Loading
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).
Load Size
The WATER LEVEL should just cover the clothes. Adjust the load size
accordingly. Loosely load clothes not higher than the top row of holes in the
washer tub. To add items after washer has started, press Start button and submerge
additional items. Close the lid and press Start button again to restart.
WARNING
Fire Hazard
Never place items in the washer that are
dampenedwith gasoline or other
flammable fluids. No washer can
completely remove oil. Do not dry
anything that has ever had any type of
oil on it (including cooking oils). Doing
so can result in death, explosion, or fire.
Light and Large-sized clothing
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and
wash them in a small amount of water. If the laundry floats during the wash cycle, it may
become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
Long laundry items
Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent
tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
Nylon net is not supplied by LG.
11
U
1
se of Water, Detergent, Bleach and Softener
2
Deposit laundry and
press the START/
PAUSE button.
START
Without water, the pulsator
turns to the left and right for
about 8 seconds to sense the
amount of laundry.
3
A proper water level
and the amount of
detergent is displayed.
PAUSE
Press
WATER DETERGENT
XL
L
M
S
l If either the inner-tub contains water or
the laundry is wet, water level may be
different from the initial set level.(It is
not malfunctioning. It is the proper
water setting for laundry.)
l Bulky and light laundry may cause a
water level lower than usual. In this
case, manually adjust the water level.
H If you feel the water level is not as per your choice you can change the water level manually.
Usage of Detergent
l The following indication of the amount of detergent is based on a concentrated detergent.
(1 detergent cup: arround 40g)
Powder Detergent Box
WATER DETERGENT
XL
L
M
S
In case of small water level:
concentrated detergent (1/2 cup).
l Regular detergent uses
Where you
deposit the
detergent
1.5 times as much as the
indicated amount.
Note : Follow detergent manufacturer's instructions for quantity of detergent.
H Use only powder detergent.
12
U
se of Water, Detergent, Bleach and Softener
Water Level and Amount of Detergent
l Concentrated
l Regular
detergent: 20g per 30 liters of water.
synthetic detergent: 30g per 30 liters of water.
l When
sensing water levels automatically, the amount of
detergent can differ according to the amount of laundry
even at the same water level.
. detergent, use one that generates less
synthetic
.
bubbles. This type of detergent is specially designed
for washers
Water
Level
Amount Amount
of Water of laundry
Regular synthetic
About 41g
About 61g
XL
61 l
L
39 l
Less than
3.5kg
About 26g
About 39g
M
30 l
Less than
2.0kg
About 20g
About 30g
S
29 l
Less than
1.0kg
About 19g
About 29g
l For
case of using liquid detergent, dissolve it with water
(detergent: water=1:1) and deposit it through the bleach
deposit hole
Less than*
Amount of Detergent
Concentrated
l In
*Rated Capacity of Model
Note : To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of
foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough
Detergent has been used, soil and lint can settle back on the clothes or the washing machine.
If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause
environmental pollution, so use it accordingly.
Adding the detergent
Add measured detergent to the detergent compartment of the dispenser drawer.
We recommend the use of powdered detergent in the dispenser when using a
delay wash function.
Detergent is flushed through the dispenser at the beginning of the wash phase.
Detergent usage may need to be adjusted for water temperature, water hardness,
size and soil level of the load.
Avoid using too much detergent in your washer, as it can lead to oversudsing and
detergent residue being left on the clothes.
Using Liquid Bleach
• Check clothing care label for special instructions and separate the
laundry to be bleached
• Dilute liquid chlorine bleach.
• Measure the recommended amount of liquid bleach carefully
following instructions on the bottle.
• Before starting the washer, pour measured amount of bleach directly
into bleach dispenser. Avoid splashing or overfilling. Powdered
bleach should be mixed with water before pouring.
Bleach dispenser
NOTE
n Never pour undiluted liquid bleach directly onto clothes or into the wash basket.
This may cause change of color or damage the laundry.
n Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remove Mixing can release
a toxic gas which may cause death.
n Do not pour powdered bleach into bleach dispenser.
13
U
se of Water, Detergent, Bleach and Softener
Using Fabric Softener
• Dilute fabric softener with water.
Undiluted fabric softener may result in spots that look like oil stains.
Softener dispenser(
)
• Measure and add the recommended amount of fabric softener into the
compartment marked with this symbol(
).
Follow manufacturer’s direction.
• Do not overfill. The dispenser hold max 35ml.
Never add more than 35ml.
Overfilling can cause early dispensing of the fabric softener which could result in stained clothes.
A cup with a pouring spout will help you avoid spilling.
• The effect of adding fabric softener may vary according to its viscosity. The stickier fabric softener makes
its effect the lower. For a sticky fabric softener it is recommended that it be diluted with water, then be
manually correct time to dispense manually is optionally applied to some models. Please keep it in mind that
fabric softener has to be diluted with water before dispensed and never poured directly on clothes.
•
•
•
•
Attention
Do not mix with detergent or bleach.
Never pour fabric softener directly on clothes. It may stain them.
Do not stop the washer during the first spin for timely dispensing.
Option washing is not designed to be used with fabric softener dispenser.
Scrud (Waxy Build up)
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener
comes into contact with Detergent. This build-up is not brought about by a fault in the machine.
If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant
smell in your washer.
If you wish to use fabric softener we recommend
• Using fabric softener sparingly.
• When filling the dispenser, do not splash or overfill.
• Clean dispenser as soon as the cycle is finished.
• Clean your machine regularly. (refer to page 21)
• Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a
build-up.
14
S pecial Guide for Stain Removal
WARNING
Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products containing ammonia.
These mixtures can produce dangerous fumes which can cause serious injury or death.
To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
Read and comply with all instructions on stain removal products.
Keep stain removal products in their original labeled containers and out of children's reach
Thoroughly wash any utensil used.
Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry
cleaning solvents or other flammable or explosive substances because they give off vapors that could ignite or explode.
Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
For successful stain removal:
• Remove stains promptly.
• Determine the kind of stain, then follow the recommended treatment in the stain
removal chart below.
• To pretreat stains, use a prewash product, liquid detergent or a paste made from
granular detergent and water.
• Use COLD water on unknown stains HOT water can set stains.
• Check care label instructions for treatments to avoid on specific fabrics.
• Check for colour fastness by testing stain remover on an inside seam.
• Rinse and wash items after stain removal.
Follow fabric care label
instructions
Stain Removal
TREATMENT
STAIN
Adhesive tape, chewing gum,
rubber cement
Baby formula, dairy products, egg
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
nonflammable dry cleaning fluid.
Use product containing enzymes to pretreat or soak stains.
Beverages (coffee, tea, soda, juice,
alcoholic beverages)
Pretreat stain. Wash using COLD water and bleach safe for fabric.
Blood
Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using
bleach safe for fabric.
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Candle wax, crayon
Chocolate
Collar or cuff soil, cosmetics
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Dye transfer on white fabric
Use packaged color remover. Wash using bleach safe for fabric.
Grass
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Grease, oil, tar (butter, fats, salad
dressing, cooking oils, car grease,
motor oils)
Ink
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Wash with chlorine bleach if safe for fabric or soak in oxygen bleach and HOT water before washing. Badly
mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes.
Mildew, scorch
Mud
Mustard, tomato
Pretreat with prewash stain remover or rub with bar soap.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Nail polish
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
Paint, varnish
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed.
OIL BASED & VARNISH : Use solvent recommended on can label. Rinse thoroughly before washing.
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, wash using bleach
safe for fabric.
Rust, brown or yellow
discoloration
Shoe polish
15
Applicable for : T70CSA13P, T7001TDDLC
16
17
AUTO OFF
PROCESS
2.
3. Add
Laundry
START
PAUSE
AUTO OFF
PROCESS
2.
3. Add
Laundry
4.
START
PAUSE
AUTO OFF
PROCESS
3. Add
Wet/Dry
Laundry
START
PAUSE
AUTO OFF
PROCESS
3. Add
only Wet
Laundry
START
PAUSE
AUTO OFF
PROCESS
2. Select the Process 3. Add
Wash+Rinse+Spin/
Wet / Dry
Rinse+Spin/
Laundry
Wash+Rinse
18
START
PAUSE
4.
5. Add
5. Add
(wash
+ rinse)
Add
Close the lid (No detergent to be added during rinse + spin).
19
F
unction Options
START
PAUSE
WATER LAVEL
PROCESS
20
C
leaning and Maintenance
When the water supply is bad, check substances like stone or sand in the filter.
If the filter is clogged with dirt, water cannot flow into the washer. Clean the filter regularly.
Cleaning the filter in the inlet valve
Before cleaning the filter in the inlet valve, completely remove the water remaining in the water hose.
1
l Turn off the water tap and put on the power
switch.
l Select cold & hot water and press
START/PAUSE
button. Let the washer operate
.
for 5 seconds
3
Disconnect water hose, and remove filter from
the inlet valve by hand or with tools. Remove
dirt with a tooth brush and clean in water.
IDE)
KS
(BAC
2
Switch off the washer and disconnect the power
cord.
l Then insert it back into the water inlet.
To Clean the Magic Filter *
1
3
2
4
5
If the magic filter is damaged, purchase a new one from LG Authorised Service Center.
To Clean the Lint Filter *
upward
If the lint filter is damaged, purchase a new one from LG Authorised Service Center.
* Parts can be different according to the model.
21
6
C
leaning and Maintenance
To prevent freezing in winter
1
Close water tap and remove the water
hose. Direct the hose toward the bottom and completely remove water
from the hose.
2
Press the SPIN button and let
it spin for 1 min. to remove
water from the tub and drain
hose.
3
Unplug the power cord.
2
Pour 50°C of hot water inside
the tub and leave it for 10 min.
3
Submerge the separated hose
in 50°C of hot water
When frozen
1
Pour 50°C of hot water on the
water tap and remove the water
hose.
4
Connect the water hose to
the washer and then start
the washer. Pour 50°C of
hot water into the water
hose.
5
Connect the water
hose to the water tap
and check if water
is draining.
Note : n Stainless steel inner tub won’t be rusted.
However, external rust may cling to it in the following causes:
l Metal product(like hairpin,etc,) that can be rusted is left inside the tub for a long time.
l Water with a lot of iron substance is used for a long time.
l Water or chlorine type bleach is left inside the tub for a long time.
n If rust is found, soak sponge or soft cloth with cleaner
(neutral cleaner) and wipe the rust.(Never use metal sponge)
22
G rounding Method
Earth wire should be connected.
If the earth wire is not connected, there is possible a danger of electric shock caused
by the current leakage .
Grounding Method with Ground insert space Terminal
If the AC current outlet has a ground terminal, then
separate grounding is not required.
Ground terminal
Grounding is
not needed
Caution
Concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords,
or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect
the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon.
Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance
Other Grounding Method
Burying Copper Plate
Connect the Ground Wire to a Ground Copper
Plate and bury it more than 75cm in the ground.
Ground Wire
75cm
Ground Copper Plate
Using Ground Wire
Connect the ground Wire to the socket provided
exclusively for Grounding.
Ground
Wire
Using a Short Circuit Breaker
If grounding methods described above are not possible,
a separate circuit breaker should be employed and
installed by a qualified electrician.
Caution
To prevent a possible explosion, do not connect ground to a gas pipe
Do not connect ground to telephone wires or lightning rods. This may be dangerous during
electrical storms.
Connecting ground to plastic has no effect
Ground wires should be connected when an extension cord is used.
23
Short-circuit
breaker
C
ommon washing problems
Many washing problems involve poor soil & stain removal, residues of lint and
scum, and fabric damage. For satisfactory washing results, follow these
instructions.
WASH PROBLEM
Problems
Possible Causes
Solutions & Preventive Measures
Poor soil
removal
Not enough detergent
Wash water temperature
too low.
Overloading the washer
Incorrect wash cycle
Incorrect sorting
Pretreat stain not done
Use correct amount of detergent for load size,
amount of soil and water
hardness.
Reduce load size.
Wash with Turbo Process.
Separate heavily soiled items from lightly soiled ones.
Pretreat stain and heavy soil according to directions shown
on page 15.
Blue Stains
Undiluted fabric softener
dispensed directly onto
fabric
Rub the stain with bar soap. Wash.
Do not overfill fabric softener dispenser and do not pour
liquid fabric softener directly onto fabric.
See page 14 for more instructions.
Black or gray
marks on
clothes
A buildup caused by the
interaction of fabric
softener and detergent can
flake off and mark clothes
Not enough detergent
Keep the recommendations against Scrud (waxy buildup).
(refer to scrud page 14.)
Use correct amount of detergent for load size, amount of soil
and water hardness.
Yellow or
brown rust
stains
Iron or manganese in
water supply, water pipes,
or water heater
To restore discolored load of whites, use rust remover safe
for fabric.
Install nonprecipitating water softener or an iron filter in
your water supply system for an ongoing problem.
Before washing, run water for a few minutes to clear lines.
Lint
Incorrect sorting
Tissues left in pocket
Overloading the washer
Wash lint givers eg towels, flannelette sheets, separately
from lint collectors eg synthetic fabrics and remove tissues in
pockets before wash. See page 11 for sorting and caring
before loading.
Do not overload the washer.
Residue or
detergent
Overloading the washer
Undissolved detergent
Use too much detergent
Do not overload the washer.
Some detergents need to be pre-dissolved, check the
detergent instructions. Try pre-dissolving the detergent.
Increase water temperature using hot water safe for fabric.
Use proper amount of detergent.
Holes, tears
or snags
Incorrect use of chlorine
bleach.
Unfastened zippers,
hooks, buckles
Ribs, tears and broken
threads
Overloading the washer
Degradation of fabric
Never pour chlorine bleach directly on fabric.
See page 17 for adding liquid bleach.
Fasten zippers, hooks, and buckles.
Remove objects in pockets. See page 11 for caring before
loading.
Do not overload the washer.
24
T
roubleshooting
If a abnormal symbol appears in the display window,
check the following before calling Customer Service Centre.
SYMPTOM
Turbo
Wash
Rinse
Spin
Water supply failure
(At this time, the lamps of
[WASH], [RINSE] blink.)
Turbo
Wash
Rinse
Spin
Is the water pressure
lowered or the filter
clogged?
Is the drain hose lowered?
Is the drain hose bent?
Is the doorsill too high?
Is the drain hose
frozen or chocked?
Spin Failure
(At this time, the lamps of
[WASH], [RINSE], [SPIN]
blink.)
Turbo
Wash
Rinse
Spin
Is the water tap
frozen?
Is water supply
discontinued?
Is the water
tap closed?
Drainage Failure
(At this time, the lamps of
[RINSE], [SPIN] blink.)
Turbo
Wash
Rinse
Spin
ITEM TO BE CHECKED
Is the laundry gathered to one side?
Is the washer tilted?
Opened lid
Is the lid closed? If the lid is open,
alarm is generated and process
cannot be proceeded.
(At this time, buzzer sounds,
the lamps of wash, spin blink)
25
S
pecification
Model
(A) T70CSA13P
(B) T7001TDDLC
Size
(A) 540(W)x540(D)x815(H)
Water tap pressure
30 -800 kPa (0.3 -8 kgf /cm 2)
Weight
(A) 30.0 kg
(B) 30.5 kg
(B) 540(W)x540(D)x850(H)
In our continuing effort to improve the quality of our appliances, it may be necessary to make changes to the
appliance without revising this manual.
26
MFL68465602
Download PDF