LG | T70CPD22N | LG T70CPD22N Owner’s Manual

P
INDIA'S
N o.1
WASHING MACHINE*
roduct Features
Washer doesn't operate while the lid is open. If the lid is open during the wash, rinse or spin
cycles, the operation stops for safety.
C
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer
properly. Just a little preventive care on your part can save you a great deal of time and
money over the life of your washer. You will find many answers to common problems
in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you
may not need to call for service at all.
FUZZY logic control
l A built-in load sensor automatically detects the laundry load and a
microprocessor optimizes washing conditions such as ideal WATER LEVEL
and washing time.
START
Owner's Manual
Please read this manual carefully and thoroughly
before operating this unit.
Record model name and serial number of the set.
Quote this information to your dealer when you
require service.
SENSING SETTING
Laundry Sensor
Water Level Sensor
Optimum
Washing
Condition
Before Starting to Wash
l Advanced technology is built into the Electronic Control System which
ensures the best washing result.
Turbo drum washing
Washing Programs
l When "Punch + 3" washing wings turn, the washing tub
MODEL : WF-N7069NN
WF-N7069NP
WF-N7039NP
T70CPD22N
turns in the opposite direction. This makes the both
sides current of water which improve wash-performance
by rubbing clothes strongly.
3 Step washing
Additional Function
Program
l 3 step washing makes the best washing performance with low tangling.
Installation
Rubbing
Rubbing and
Shaking
Shaking and
Disentangling
Care and Maintenance
NOTE : Be sure to remove the unit from the carton base, otherwise the
machine will not be able to operate properly.
Troubleshooting
Specification
Installation Check Sheet
Terms of Warranty
P/No.: MFL60983102
For any query related to the after sales service you may please contact us
on the numbers listed below :
I
F
dentification of Parts
Safety Information
4
Identification of Parts
7
Function Information
8
Preparation Before Washing
9
Use of Water, Detergent, Bleach and Softener
10
Special Guide for Stain Removal
13
Function of each Button
SOAK Wash
FUZZY Wash (Normal Wash)
14
16
17
WOOL Wash
17
QUICK WASH
17
JEANS Wash
17
SILENT Wash
Option Washing
19
20
DELAY START (RESERVATION) Wash
21
Other Useful Functions
22
Placing and Leveling
23
Connecting Water Supply Hose
24
Connecting Drain Hose
25
Grounding Method
26
Cleaning and Maintenance
27
Common washing problems
29
Troubleshooting
Specification
Installation Check Sheet
Terms of Warranty
30
POWDER DETERGENT
Box for delayed
washing.
** LINT FILTER /
MAGIC FILTER
Clean regularly to
stop linting on the
clothes load.
BLEACH
DISPENSER
Our machine provides various washing methods which suits variou s conditions
and types of laundry.
START/PAUSE
BUTTON
Use to start or
stop the washing
machine
temporarily.
SOAK Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove dirt and
grime. (refer to page 16)
(2 adjustable legs are optional, some models have provision for 1 adjustable leg)
DELAY START Wash
DELAY START Wash is used to delay the finishing time of the operation.
The number of hours to be delayed can be set by the user accordingly. (refer to page 21)
OPTION WASH
When the user needs only SPIN, RINSE/SPIN, RINSE, WASH/RINSE, WASH, WASH/RINSE/SPIN,
SOAK/WASH/RINSE/SPIN. (refer to page 20)
Screw
Snap Ring
U
S
Using Fabric Softener
When you are cleaning the washing machine, do not apply water directly to
any part of the washing machine.
It will cause short circuit and electric shock.
6
se of Water, Detergent, Bleach and Softener
Water Level and Amount of Detergent
Using Water
Amount of WATER LEVEL
• This machine detects the quantity of laundry automatically, then sets the
WATER LEVEL and proper amount of Detergent.
• When you select a wash program, the WATER LEVEL will be shown on
the control panel.
• The following table shows the amount of water.
• When the WATER LEVEL is automatically detected, it may differ depending
on the quantity of laundry even though the same WATER LEVEL is indicated
on the control panel.
Terry cloth, Chenille Towels, Nappies, Diapers
Synthetics, Corduroy, P ermanent Press, Socks
Using Detergent
Check before Loading
Detergent
• Check all pockets to make sure that they are emtpy. Things such as nails, hairclips,, matches,
pens, coins, and keys can damage both your washer and your clothes.
• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
• Pretreat any dirt and stains.
• Make sure the clothes are washable in water.
• Check the washing instructions.
• Remove tissue in pockets.
Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems.
Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.
Choosing the right Detergent
WIRE
Amount of Detergent
Concentrated detergent: 20g per 30 liters of water.
l Regular synthetic detergent: 30g per 30 liters of water.
l When sensing water levels automatically, the amount of
detergent can differ according to the amount of laundry
even at the same water level.
. detergent, use one that generates less
l For synthetic
.
bubbles. This type of detergent is specially designed
for washers
l In case of using liquid detergent, dissolve it with water
(detergent: water =1:1) and deposit it through the bleach
deposit hole
l
We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or granulated
soap powders should not be used in your washing machine. When washing woolens remember to use
Detergent suitable for washing woolens.
• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer.
Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
• Use a pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.
(For more detail refer to page13)
Water
Level
Amount
of Water
10
65 l
Less than*
Amount
of laundry
Regular
Concentrated synthetic
About 45g
About 65g
9
61 l
Less than 4.0kg
About 39g
About 58g
8
51 l
Less than 3.5kg
About 38g
About 57g
About 49g
7
42 l
Less than 3.0kg
About 33g
6
38 l
Less than 2.5kg
About 29g
About 44g
5
34 l
Less than 2.0kg
About 25g
About 38g
4
32 l
Less than 1.5kg
About 22g
About 33g
3
29 l
Less than 1.0kg
About 19g
About 28g
2
29 l
Less than 0.6kg
About 16g
About 24g
1
23 l
Less than 0.3kg
About 13g
About 20g
*Rated Capacity of Model
Note : To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of
foam may look good, but it does not cotribute to cleaning your clothes. No foam means not enough
Detergent has been used; soil and lint can settle back on the clothes or the washing machine.
If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause
environmental pollution, so use it accordingly.
Adding the detergent
Open the detergent dispenser and deposit the appropriate amount of detergent where you deposit the detergent
Powder Detergent dispenser.
Some detergents MUST be fully dissolved before adding to your machine to get the best wash results.
Check the instructions on the detergent packet.
If you use powdered detergent it is essential that the required amount be fully dissolved in very hot water before
being added to warm or hot water for the actual wash.
Pre-dissolving detergent in warm water when washing in cold water can improve its performance.
Powder Detergent Box
Where you
deposit the
detergent
Using Liquid Bleach
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).
Load Size
The WATER LEVELF should just cover the clothes. Adjust the load size accordingly. Loosely load clothes not higher
than the top row of holes in the washer tub. To add items after washer has started, press Start button and submerge
additional items. Close the lid and press Start button again to restart.
Bleach dispenser
• Check clothing care label for special instructions and separate the
laundry to be bleached
• Dilute liquid chlorine bleach.
• Measure the recommended amount of liquid bleach carefully
following instructions on the bottle.
• Before starting the washer, pour measured amount of bleach directly
into bleach dispenser. Avoid splashing or overfilling. Powdered
bleach should be mixed with water before pouring.
Light and Large-sized clothing
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and
wash them in a small amount of water. If the laundry floats during the wash cycle, it may
become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
NOTE
n Never pour undiluted liquid bleach directly onto clothes or into the wash basket.
This may cause change of color or damage the laundry.
n Do not pour powdered bleach into bleach dispenser.
10
9
11
pecial Guide for Stain Removal
For successful stain removal:
• Dilute fabric softener with water.
Undiluted fabric softener may result in spots that look like oil stains.
Softener dispenser(
• Remove stains promptly.
• Determine the kind of stain, then follow the recommended treatment in the stain
removal chart below.
• To pretreat stains, use a prewash product, liquid Detergent, or a paste made from
granular Detergent and water.
• Use COLD water on unknown stains because HOT water can set stains.
• Check care label instructions for treatments to avoid on specific fabrics.
Follow fabric care label
• Check for colorfastness by testing stain remover on an inside seam.
instructions
• Rinse and wash items after stain removal.
)
• Measure and add the recommended amount of fabric softener into the
compartment marked with this symbol(
).
Follow manufacturer’s direction.
Fabric softener is automatically dispensed in the final rinse with
indication beep.
If you want extra rinse, you must add fabric softener manually
when indication beep rings in the final rinse.
This maximize the fabric softener function.
• Do not overfill. The dispenser hold max 35ml.
Never add more than 35ml.
Overfilling can cause early dispensing of the fabric softener which could result in stained clothes.
A cup with a pouring spout will help you avoid spilling.
• The effect of adding fabric softener may vary according to its viscosity. The stickier fabric softener makes
its effect the lower. For a sticky fabric softener it is recommended that it be diluted with water, then be
manually correct time to dispense manually is optionally applied to some models. Please keep it in mind that
fabric softener has to be diluted with water before dispensed and never poured directly on clothes.
•
•
•
•
Do not yank the power cord in an attempt to disconnect the power plug.
Securely hold the power plug to unplug the machine.
Failure to observe these instructions may cause electric shock or fire due to shortcircuit .
Ensure No water logging near or below washer to prevent rusting.
Rusting on certain parts may result in product failure
Care Labels
8
se of Water, Detergent, Bleach and Softener
Do not tamper with controls.
It may lead to electric shock, fire , break down, deformation.
Do not use water hotter than 60°C.
Use of excessively hot water may cause damage to fabrics or cause
leakage of water.
Long laundry items
Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent
tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
Nylon net is not supplied by LG.
"*" Parts can be different according to the model.
"**" LINT FILTER (Applicable for WF-N7069NN/WF-N7069NP)
MAGIC FILTER (Applicable for WF-N7039NP, T70CPD22N)
7
Do not attempt to repair or replace any part of this appliance unless
specifically recommended in this Owner’s Manual, or in published userrepair instructions that you understand and have the skills to carry out.
Operating the machine with improperly replaced parts may be a cause for fire or
electric shock.
Loading
Other washing method
Anti-rat cover
• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage
if a break or rupture should occur. Check the condition of the fill hoses; they may need
replacement after 5years.
• When the air temperature is high and the water temperature is low, condensation may
occur and thus wet the floor.
• Wipe off dirt or dust on the contacts of the power plug.
Using unclean power plug may cause fire.
• Before discarding a washer, or removing it from service, remove the washer lid to
prevent children from hiding inside.
Children may be trapped and suffocated if the lid is left intact.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially
disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
Pretreatment on stains or heavy soil
SOAK Wash
CAUTION
• Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded.
Flooded floors may induce electricity leakage, further resulting in electric shock or fire.
• If, during spinning, opening the lid does not stop the tub within about 15 seconds,
immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause injuries.
Never reach into washer while it is moving.
Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.
U
• SOIL (Heavy, Normal, Light)
Separate clothes according to the type and amount of soil.
• COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
• LINT (Lint Producers, Collectors) Separate lint producers and lint collectors.
QUICK WASH can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to page 17)
It may ignite or explode.
WHEN NOT
IN USE
5
Use this Program for heavily soiled durable garments e.g. overalls, jeans.
Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed (refer to page 17)
QUICK WASH
Accessories
CAUTION
NOTE : Pressing Power button to turn off does NOT
disconnect the appliance from the power supply.
reparation Before Washing
Lint Produ cers
Lint Collectors
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted
with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water.
Do not use or place these substances around your washer or dryer during operation.
• Use this appliance only for its intended purpose as described in this Owner’s Manual.
• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s wash and care instructions.
• To minimize the possibility of electric shock, unplug this appliance from the power
supply or disconnect the washer at the household distribution panel by removing the
fuse or switching off the circuit breaker before attempting any maintenance or cleaning.
CAUTION
To get the best results, different fabrics need to be washed in different ways.
The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed.
Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them
• Before washing your woolens check the care label for the washing instructions.
• When washing woolens use a mild Detergent recommended for washing wool.
• Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
• To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.
(The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)
Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages.
(Ensure that the whole article is suitable for machine washing and not just the backing material.)
You may wish to handwash these articles and place them in the machine to spin dry.
BASE
WHEN USING
THE WASHER
•The base opening must not be obstructed by carpeting when the washing machine is installed
on a carpeted floor.
•Install or store where it will not be exposed to temperatures below freezing or exposed to the
weather (Rain / Water Splash).
If the product is exposed to such conditions,electric stock, fire, break down or deformation may occur.
•Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.
If not grounded properly, break down and leakage of electricity may occur, which may cause electric
shock.
•Must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get damaged, possibly causing fire or
electric shock.
•Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
•Do not connect ground to a gas pipe.
It can cause explosion.
•Do not connect ground to telephone wires or lightning rods.
This may be dangerous during electrical storms.
•Washer shall be placed in dry areas specifically during rainy season.
Humid conditions may cause rusting which may result in product failure.
P
Do not mix chlorine bleach with other household chemicals such as toilet cleaners,
rust removers, acids (such as vinegar) or product containing ammonia.
Mixing different chemicals can produce toxic gases which may cause death.
Do not put your hand, foot or anything under the washing machine
while the washing machine is in operation.
There is a rotating mechanism under the machine, so you could be injured.
Under certain conditions hydrogen gas may be produced in a water heater that has not been
used for two weeks or more. Hydrogen gas can be explosive under these circumstances.
If the HOT water has not been used for two weeks or more, prevent the possibility of
damage or injury by turning on all Hot water faucets and allowing them to run for several
minutes. Do this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas is flammable, do not smoke or use an open flame or appliance during this process.
JEANS Wash
Washing according to the condition of laundry
NOTE
PROPER
INSTALLATION
WARNING
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Do not use a plug socket and wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire , break down, and/or deformation
of parts.
Do not touch the power plug with a wet hand.
WARNING
Sorting
Wool clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 17)
DRAIN HOSE
Keep the drain hose
flipped down while
washing is in progress.
ADJUSTABLE LEG
Use to level the washing
machine for correct
balance & spin
operation.
LG ELECTRONICS INDIA PVT. LTD. CUSTOMER CARE CENTRE
WATER
HEATER
SAFETY
WHEN USING
THE WASHER
It will cause electric shock
: Failure to comply with the instructions under this
sign may result in minor physical injuries or
damages to the product.
Use this Program for everyday washing e.g. sheets, towels, T-shirts. (refer to page 17)
WOOL Wash
CASTORS
Use for easy
translocation
Drain hose
sign may result in major physical injuries or death.
CAUTION
* Look for acare label on your clothes This will tell you about the fabric content of your g arment
and how it should be washed.
Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.
FUZZY(Normal) Wash
POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to
avoid a hazard.
TUB
Water supply hoses
WARNING : Failure to comply with the instructions under this
WARNING
afety Information
• Keep the area underneath and around your appliances free of combustible
materials such as lint, paper, rags, chemical, etc.
Operating with such materials around the machine may trigger explosion or
fire.
• Close supervision is necessary if this appliance is used by or near children.
Do not allow children to play on, with, or inside this or any other appliance.
There is potential danger that children might drown in the tub.
4
Different types of laundry washing
WATER SUPPLY
HOSE
Make sure the
water does not
leak.
FUNCTION
SELECTOR
Regd. Office : A-27, Mohan Co-operative Industrial Estate, Mathura Road, New Delhi-110044
: This is a warning sign specifying user’s applications which might
be dangerous.
S
afety Information
YOUR
LAUNDRY
AREA
This booklet is divided into 2 parts : Warning and Caution.
31
unction Information
Body
LG Electronics India Pvt. Ltd.
Read carefully and thoroughly through this booklet as it contains important safety information
that will protect the user from unexpected dangers and prevent potential damages to the product.
3
2
Customer Information Center
S
afety Information
: This is a sign specifying ‘Strictly Forbidden’ applications.
Introduction
AUTO
POWER
OFF
WASHING
S
ontents
Attention
Do not mix with detergent or bleach.
Never pour fabric softener directly on clothes. It may stain them.
Do not stop the washer during the first spin for timely dispensing.
Option washing is not designed to be used with fabric softener dispenser.
Scrud (Waxy Build up)
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener
comes into contact with Detergent. This build-up is not brought about by a fault in the machine.
If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant
smell in your washer.
Stain Removal
STAIN
Adhesive tape, chewing gum,
rubber cement
Baby formula, dairy products, egg Use product containing enzymes to pretreat or soak stains.
Beverages (coffee, tea, soda, juice, Pretreat stain. Wash using COLD water and bleach safe for fabric.
alcoholic beverages)
Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using
Blood
bleach safe for fabric.
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Candle wax, crayon
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Chocolate
23
16
9
3
4
3
2
1
5
4
3
2
Time Left
SOAK
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Collar or cuff soil, cosmetics
Pretreat with prewash stain remover or rub with bar soap.
Dye transfer on white fabric
Use packaged color remover. Wash using bleach safe for fabric.
Grass
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Grease, oil, tar (butter, fats, salad
dressing, cooking oils, car grease,
motor oils)
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
using hottest water safe for fabric.
Ink
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Mildew, scorch
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly
mildewed fabrics may be permanently damaged.
Mud
Brush off dry mud. Pretreat or soak with product containing enzymes.
If you wish to use fabric softener we recommend
Mustard, tomato
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
• Using fabric softener sparingly.
• When filling the dispenser, do not splash or overfill.
• Clean dispenser as soon as the cycle is finished.
• Clean your machine regularly. (refer to page 28)
• Cold water washing increases the chance of this build-up occurring. We recommend a regular WARM or
HOT wash e.g. every 5th wash should be at least a warm one.
• Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a
build-up.
Nail polish
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
Paint, varnish
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed.
OIL BASED & VARNISH : Use solvent recommended on can label. Rinse thoroughly before washing.
Rust, brown or yellow
discoloration
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
Shoe polish
LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach
safe for fabric.
12
Press the PROGRAM button to select the SOAK Program.
TREATMENT
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
nonflammable dry cleaning fluid.
13
Select washing time by pressing the Wash button repeatedly. (Wash timing cannot be set to zero in
SOAK Program)
SOAK
(refer to page 22)
(refer to page 21)
14
15
16
Press the RINSE button to
select the desired no. of rinse
cycles.
When you want to only
drain, press SPIN button.
Time Left
Then press START/PAUSE
button.
Press both the SPIN button and the DELAY button simultaneously.
Time Left
Time Left
Time Left
Wait until the water in the
washing tub drains completely
and then press POWER button
to finish the activity.
SPIN
DELAY
If you want to unlock during wash, press both the SPIN and the DELAY button simultaneously again.
To see the remaining time for each process, first press START/PAUSE button and then press one of the
WASH, RINSE and SPIN buttons.
19
18
17
C
lacing, Leveling and Installation
Improper installation of the washer may cause noise and malfunctioning.
Note : 1. The ventilating openings in the base area must not be obstructed by carpeting when the washing machine is
installed on a carpeted floor.
2. Install the washing machine on a level and firm
surface, any tilt should be less than 4°.
C
onnecting Water Supply Hose
Normal Type
1
(Normal tap without thread & one touch type inlet hose.)
onnecting Drain Hose
Before connecting Drain Hose, check your Drain Hose model and choose the correct
instructions.
How to adjust leveling
Middle
connector
Installation area
Pressing Rod
1
Insert the drain hose to the connecting area at the body.
2
Loosen the fixed nuts to connect the connector to the tap
2
Install the washer on flat and firm surface.
Fixed sticker
NOTE
Guide plate
In case tap is too large.
Fixing Connectors to the Tap
3
Turn the adjustable legs to set the washer
horizontal (Both the front legs).
2
H Don't add anything under back side legs.
The Basement is not flat, fill the water just touching the
Pulsator and see uniform distribution. If not, adjust the
legs as shown in the figure.
Distance between drain hose and the wall
Distance between drain hose and the wall should be more
than 10cm, and the distance between the other part or the
rear part and the wall should be more than 2 cm.
.
Connector
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
Checking level
4
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
More than 2cm
More than 2cm
Top View
More than 10cm
3
Anti-rat cover installation
5
Press down the pressing rod of the Water Supply
Hose which was separated from middle connector
(refer to Step1) and then join it to the middle
connector.
Checking Proper placement
Pressing rod
Insert the anti rat cover firmly from back side or
Front side of washing machine and screw it.
6
FIXING POSITION
Screws
Anti Rat Cover
If the AC current outlet has a ground terminal, then
separate grounding is not required.
1.
2.
Grounding is
not needed
3.
4.
Concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers
only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's
manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord
replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular
attention to plugs, wall outlets, and the point where the cord exits the appliance.
5.
6.
7.
Burying Copper Plate
8.
Connect the Ground Wire to a Ground Copper
Plate and bury it more than 75cm in the ground.
Ground Wire
To Clean the Magic Filter
9.
10.
75cm
Pressing handle
11.
Using Ground Wire
Make sure that the
hose is not crushed.
After connecting the hose, open the tap to check
for any water leakage.
If the connection leaks, close the tap and start
again from step 1.
If you skip step 1, water leakage may occur.
Terms & Condition
Ground terminal
Ground Copper Plate
Avoid submerging
the end of hose.
12.
13.
Ground
Wire
Connect the ground Wire to the socket provided
exclusively for Grounding.
If the magic filter is damaged, purchase a new one from LG Authorised Service Center.
Less than 3m
To Clean the Lint Filter
Short-circuit
breaker
If grounding methods described above are not
possible, a separate circuit breaker should be
employed and installed by a qualified electrician
Extension hose is
used.
Turn inside out and wash it to
remove dirt.
Press and then pull forward
the lint filter from the washing
tub to the arrow direction.
Using a Short Circuit Breaker
Check for water leakage
Press the corners of the machine diagonally
as shown in the figure, If any movement is observed,
adjust the legs for proper leveling.
Earth wire should be connected.
If the earth wire is not connected, there is possible a danger of electric shock caused
by the current leakage.
Connector
Middle
Connector
Water Supply Hose
High Base
&
Middle Base
Low Base
Make sure that the hose is
not crushed between the
wall and the washer .
The hose is clogged by
alien substances.
Connecting Middle Connector and Water Supply Hose
This LG Washing Machine comes with 2 year warranty, from the date of purchase, that comprises of a 2 year
warranty on all Parts except Lint filter, knobs, inlet/outlet hose & Top Covers, subject to that the warranty card bears
the rubber stamp, date and signature of our Authorized Dealer.
Other Grounding Method
The hose is placed
over a doorsill.
Connector
Middle
Connector
Fixed sticker
Less than 10cm
Less than 6cm
Less than 2m
Rubber packing
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
plate. Then follow step1.
Adjustable leg
1. Press the hose clip.
2. While pressing, push the hose towards
the body.
3. Release the hose clip after pushing the
hose.
Rubber packing
screw
Untighten the screw of the connector so that the
tap can be placed in the middle.
WARRANTY
Grounding Method with Ground insert space Terminal
Fixed Sticker
Pressing Handle
Water Supply Hose
1
G
22
rounding Method
How to connect the drain hose
Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose.
21
20
Insert it back into same
place and push until click
sound heard.
l When the lint filter is worn out, etc., contact a LG Service Center for a new one.
C
leaning and Maintenance
24
C
ommon washing problems
When there is a fear of freezing
• Close the water taps and remove the Water Supply Hose.
• Remove the water which remains in the water supply.
• Lower the drain hose and drain the water in the bowl and the drain hose by spinning.
Many washing problems involve poor soil & stain removal, residues of lint and scum, and
fabric damage. For satisfactory washing results, follow these i nstructions.
WASH PROBLEM
Problems
Poor soil
removal
If frozen
• Remove the water supply hose, and immerse it in HOT water at approx.. 40 C.
• Pour approx.. 2 liters of HOT water at approx.. 40 C, into the bowl and let it stand for 10 minutes.
• Connect the water supply hose to the water tap and confirm that the washing machine performs the
supply and drainage of water.
Wash Inner-tub
Leave the lid open after washing to allow moisture to evaporate. If you want to clean
the inner-tub use a clean soft cloth dampened with liquid Detergent, then rinse. (Do
not use harsh or gritty cleaners.)
Inlet Hoses
Exterior
Hoses connecting washer to faucet should be replaced every 5 years.
Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with
sharp objects.
Long Vacations
Be sure water supply is shut off at faucets. Drain all water from hoses if weather will
be below freezing.
• Not enough Detergent
• Wash Water Temperature
too low.
• Overloading the washer
• Incorrect wash cycle
• Incorrect sorting
• Do not pretreat stain
• Use correct amount of Detergent for load size, amount of
soil and water Hardness.
• Use WARM or HOT water for normal soil.
• Rub the stain with bar soap. Wash.
• Do not overfill fabric softener dispenser and do not pour
liquid fabric softener directly onto fabric.
See page 12 for more instructions.
Black or gray
marks on
clothes
• A buildup caused by the
interaction of fabric softener
and Detergent can flake off
and mark clothes
• Not enough Detergent
• Keep the recommendations against Scrud(waxy buildup).
(refer to scrud page12.)
• Use correct amount of Detergent for load size, amount of soil
and water Hardness.
If you use fabric softener or do regular COLD water washing, it is very important that you occasionally clean the
inside of your washer.
Yellow or
brown rust
stains
• Iron or manganese in
water supply, water pipes,
or water heater
• Fill your washer with HOT water.
• Add about two cups of a powdered Detergent that contains phosphate.
• Let it operate for several minutes.
• Stop the washer, open the lid and leave it to soak overnight.
• After soaking, drain the washer and run it through a normal cycle.
Lint
• Incorrect sorting
• Tissues left in pocket
• Overloading the washer
• To restore discolored load of whites, use rust remover safe
for fabric.
• Install nonprecipitating water softener or an iron filter in
your water supply system for an ongoing problem.
• Before washing, run water for a few minutes to clear lines.
• Wash lint givers eg towels, flannelette sheets, separately
from lint collectors eg synthetic fabrics and remove tissues in
pockets before wash. See page 9 for sorting and caring
before loading.
• Do not overload the washer
• Concentrated bleaches and diaper sanitizer will cause damage to the paintwork and components of your washer.
• Hydrocarbon solvents i.e. petrol, paint thinners and lacquer thinners, etc. can dissolve plastic and blister paint
(Be careful when washing garments stained with these solvents as they are flammable DO NOT put them in
washer or dryer.)
• Some pretreatment sprays or liquids can damage your washer’s control panel.
• Use of dyes in your washer may cause staining of the plastic components. The dye will not damage the machine
but we suggest you thoroughly clean your washer afterwards. We do not recommend the use of dye strippers in
your washer.
• Do not use your washer lid as a work surface.
28
Residue or
Detergent
Holes, tears,
or snags
• Overloading the washer
• Undissolved Detergent
• Use too much Detergent
• Incorrect use of chlorine
bleach.
• Unfastened zippers,
hooks, buckles
• Ribs, tears and broken
threads
• Overloading the washer
• Degradation of fabric
• Do not overload the washer.
• Some Detergents need to be pre-dissolved, check the Detergent
instructions. Try pre-dissolving the Detergent.
• Increase Water Temperature using HOT water safe for fabric.
• Use proper amount of Detergent.
• Never pour chlorine bleach directly on fabric.
See page 11 for adding liquid bleach.
• Fasten zippers, hooks, and buckles.
• Remove objects in pockets. See page 9 for caring before
loading.
• Do not overload the washer.
29
• Is the water tap shut off?
• Is the water supply cut off ?
• Is the tap or water supply hose frozen ?
• Is the drain hose positioned correctly?
• Is the drain hose bent or placed too high?
• Is the internal part of the hose or drain pump
(only pump model) clogged with impurities?
• Is the laundry evenly balanced?
• Is the washing machine placed on a flat surface?
• Please call your nearest LG Electronics service center
for help.
Size
Weight
Power failure
Water tap pressure
a) WF-N7069NN / WF-N7069NP / WF-N7039NP
b) T70CPD22N
a) 540(W)x540(D)x815(H)
b) 540(W)x540(D)x835(H)
a) 31.5kg
b) 32.5kg
30 - 800 kPa (0.3 - 8.0 kgf/cm2)
Overflow failure
30
31
FATL
Company Copy
Dt. of pur.: _______________ M/C. S.No.:_______________
Name Of Customer : ________________________________________________
Address: _______________________________________________________
Address: _______________________________________________________
_________________________________________________________
__
Tel:_____________(Resi)_____________(Mob). Email :_________________________
Tel:_____________(Resi)_____________(Mob). Email :_________________________
Tick Appropriate (by Service Engineer)
Tick Appropriate (by Service Engineer)
Yes/No
Remarks
S.No.
Check Point
1 Physical condition of the Machine is satisfied?
Electrical condition of household wiring / earthing for
2
washing machine is proper?
3 Advised to turn off machine after use?
4 Explained Fixing of Inlet Hose Adapter to Tap?
Explained Leg Adjustment & Common Conditions
5
when Levelling Required?
Explained Cleaning of Lint Filter and Required
6 Cleaning Frequency?
Explained Cleaning of Inlet Valve Filter and
7
Required Cleaning Frequcny?
8 Explained Cleaning of Tub and Required Cleaning
Frequency?
9 Explained Regular Check Up and Safety Instructions ?
10 Anti Rat Cover installed?
Inlet Hose and Drain Hose checked for water
11 leakage after connection?
12
Leveling check & adjusted?
Explain Clothes Balancing, Proper Cloth Separation
for best Wash?
13
14
15
Explain all Features of the machine to customer?
16
Explain Common Errors ( IE,OE,UE,dE,PE,AE,FE etc)
16
Explain Common Errors ( IE,OE,UE,dE,PE,AE,FE etc)
17
Explained unbalance error in Spin Mode?
17
Explained unbalance error in Spin Mode?
18
Explain all Features of the machine to customer?
18
Warranty terms explained?
Yes/No
Remarks
Leveling check & adjusted?
Explain Clothes Balancing, Proper Cloth Separation
for best Wash?
Demo given to customer?
14
15
Model
Internal sensing
failure
Installation Check sheet
Name Of Customer : ________________________________________________
12
• Is the lid closed?
LG Electronics
Machine :_______________ Colour : ________________ Job No.:__________________
13
Door(Lid) Open
Dealer’s Signature
Dt. of pur.: _______________ M/C. S.No.:_______________
S.No.
Check Point
1 Physical condition of the Machine is satisfied?
Electrical condition of household wiring / earthing for
2
washing machine is proper?
3 Advised to turn off machine after use?
4 Explained Fixing of Inlet Hose Adapter to Tap?
Explained Leg Adjustment & Common Conditions
5
when Levelling Required?
Explained Cleaning of Lint Filter and Required
6 Cleaning Frequency?
Explained Cleaning of Inlet Valve Filter and
7
Required Cleaning Frequcny?
8 Explained Cleaning of Tub and Required Cleaning
Frequency?
9 Explained Regular Check Up and Safety Instructions ?
10 Anti Rat Cover installed?
Inlet Hose and Drain Hose checked for water
11 leakage after connection?
• Check if electric power has gone off.
Spin Failure
TEL.
_________________________________________________________
__
• Is the Hot hose connected to cold?
• Is the Cold hose connected to hot?
Drainage Failure
TEL.
Machine :_______________ Colour : ________________ Job No.:__________________
Check up
• Is the water pressure low or is the filter of the inlet
valve clogged with impurities?
• Reduce load size.
• Wash with JEANS or SOAK wash cycle for heavy soiled
laundry.
• Separate heavily soiled items from lightly soiled ones.
• Pretreat stain and heavy soil according to directions shown
on page 9.
• Undiluted fabric softener
dispensed directly onto
fabric
Products that might damage your washing machine
Water Supply
Failure
DEALER’S NAME & ADDRESS
FATL
Customer Copy
Error Message
CUSTOMER’S NAME & ADDRESS
Customer’s Signature
Installation Check sheet
Before calling for service, check the problem against the list bellows.
Symptom
Blue Stains
Cleaning the Inside of your Washer
T
DATE OF PURCHASE :
This Card is valid only if it is filled in and stamped by our authorised dealer on the date of purchase.
27
roubleshooting
Solutions & Preventive Measures
Possible Causes
26
25
CUSTOMER’S COPY
UNIT SERIAL No. :
Adjustable Leg
23
Warranty is not applicable in any of the following cases:
MODEL No. :
Push
Press & Pull
The warranty is confined to the first purchaser of the Washing Machine only & is non-transferable.
Repairs & replacements will be carried out by the dealer from whom the product has been purchased, or
through the Authorized Service Centers of LGEIL. In case the customer shifts the place of residence during
warranty period, it is advised to contact Authorized Service Centre directly or call our help line.
Repairs under warranty shall be carried out by an authorized service personnel only. The details of centralized
help lines are attached.
For units installed beyond municipal limits of the jurisdiction of company's Authorized Service Center, it is
responsibility of the purchaser to contact the nearest authorized service center and bring the unit to the
authorized service center at its own cost and risk. All expenses incurred in collecting the units or parts thereof
from the company's authorized service center, as well as expenses incurred with deputizing of service
personnel/technicians towards conveyance and other incidentals etc. will be borne by the customer. Local
Charges for transportation and handling charges may vary from location to location. Customers are advised to
verify before. In case the customer desires to bring the unit on its own to the Authorized Service Centre, the
same shall be at its own risks & consequences.
The concerned authorized service center will advise the customer whether to effect the repairs at site or at the
authorized service center.
Call registered with the centralized helpline/Authorized service center, wherein only cleaning of the unit/parts
in the unit due to dust accumulation on portions of the unit, general explanations/returning, are not to be
considered as defects.
In case of repairs or replacement of any part/s of the unit, this warranty will thereafter continue and remain in
force only for the unexpired period of the warranty. Replacement of parts would be purely at the discretion of
LGEIL alone. In case the replacement of the entire unit is being made, (subject to the sole discretion of LGEIL),
the same model shall be replaced and in the event such model has been discontinued, it shall be replaced with
the model of price equivalent at the time of purchase.
In case of any damage to the product / customer abuse/ repairs by un-authorised personnel's/ misuse
detected/ by the Authorized Service Center personnel, the warranty conditions are not applicable and repairs
will be done subject to availability of parts and on a chargeable basis only.
This warranty shall not cover any consequential or resulting liability, damage or loss to property or life arising
directly or indirectly out of any defect in the Washing Machine. The company's obligation under this warranty
shall be limited to repair or providing replacement of defective parts only under the warranty period.
The company or its Authorized Service Center reserves the right to retain any part/s or component replaced at
its discretion, in the event of a defect being noticed in the equipment during warranty period.
While the company will make every effort to carry out repairs at the earliest, it however is made expressly clear
that the company is under no obligation to do so in a specified period of time.
Warranty does not cover accessories external to the equipment supplied by the dealer.
If any coloured internal or external components are replaced, there will be commitment to ensure that the
shades match with the original or other components. The replaced shades, patterns, tints may vary from the
customer's unit due to continuous usage of the unit. Any matching components changed at customer's
request will be on chargeable basis except the component which actually needed
Demo given to customer?
Warranty terms explained?
Name of ASC :____________ Installation Dt : __________________ Installed by : _____________
Name of ASC :____________ Installation Dt : __________________ Installed by : _____________
Customer Remarks If Any :_________________________________________
________________________________________________________________
Customer Remarks If Any :_________________________________________
________________________________________________________________
I Here by certified by above Checks & Demo have been done to me with full of satisfaction and
I am fully satisfied with the machine installation and performance of washing machine and I
agree to take care of machine, suggestions (If Any) in respect of safety.
I Here by certified by above Checks & Demo have been done to me with full of satisfaction and
I am fully satisfied with the machine installation and performance of washing machine and I
agree to take care of machine, suggestions (If Any) in respect of safety.
Signature Of Customer
Signature Of Customer
Date :
Time:
For Best Use, Please Read the User’s Manual Properly.
Date :
Time:
For Best Use, Please Read the User’s Manual Properly.
Download PDF

advertising