LG | 26LH250C | LG 32LH200H Owner’s Manual

ENGLISH
OWNER’S MANUAL
LCD TV
Please read this manual carefully before operating
your set and retain it for future reference.
www.lg.com
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
Wall Mounting Bracket(Separate purchase)
RW120
RW230
AW-47LG30M
(19/22LH2***)
(26/32LH2***)
(32/37/42LH2***)
ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact
the dealer where you purchased the TV.
■
Image shown may differ from your TV.
MOD
E
This item is not included for all models.
PO
W
ER
ENER
GY
SAV
SAVIN
ING
* Lightly wipe any stains or
fingerprints on the surface of the TV with the
polishing cloth.
LIS
T
M
UT
E
Q.V
IEW
ME
NU
Q.M
EN
U
RETU
RN
IN
FO
i
GU
ID
/ EX
IT
Polishing Cloth Do not use excessive force.
Polishing cloth for This may cause scratching or
use on the screen. discolouration.
E
MAR
FA K
V
Remote Control
Owner’s Manual
Power Cord
Batteries
ACCESSORIES
AV
V
Ferrite Core
(This item is not included for
all models.)
(Only 22/26/32/37/42 LH200H)
Dual Lock™
(This feature is not available for all models.)
(Refer to P. 9)
x4
(Only 19/22LH2***,)
(Only 26/32/37/42LH2***)
(Only 26/32/37/42LH2***)
Cable management clip
1-screw for stand fixing
Bolts for stand assembly
(Refer to p. 10)
(Refer to p.8)
(Refer to p. 7)
or
(Only 26/32/37/42LH2***)
Protection Cover
(Refer to p. 11)
Protective Bracket and
Bolt for Power Cord
(Refer to p.8)
Use of ferrite core (This feature is not available for all models)
Ferrite core can be used to reduce the electromagnetic
wave when connecting the power cord.
The closer the location of the ferrite core to the power
plug, the better it is.
Install the power plug closely.
1
CONTENTS
ACCESSORIES
............................................
1
PREPARATION
CONTENTS
Front Panel Controls..................................................... 4
Back Panel Information ................................................ 5
Stand Installation........................................................... 7
Attaching the TV to a desk........................................8
How to secure the power cable .............................................8
Positioning your display ...........................................8
Kensington Security System ....................................8
Careful installation advice ....................................... 9
Swivel Stand ....................................................................9
How to use Dual Lock™....................................................9
Back Cover for Wire Arrangement .......................... 10
Not Using the desk-type stand.................................11
Desktop Pedestal Installation.................................12
Wall Mount: Horizontal Installation ........................ 12
EXTERNAL EQUIPMENT SETUP
Antenna Connection................................................... 13
HD Receiver Setup ...................................................... 14
DVD Setup..................................................................... 16
VCR Setup ..................................................................... 19
Insertion of CI Module............................................... 21
Digital Audio Out Setup ........................................... 22
Headphone Setup....................................................... 22
Speaker Output Setup............................................... 23
USB Setup..................................................................... 23
PC Setup........................................................................ 24
- Screen Setup for PC Mode................................27
WATCHING TV / PROGRAMME CONTROL
Remote Control Key Functions................................ 31
Turning on the TV....................................................... 33
Initializing Setup ....................................................... 33
Programme Selection ................................................ 33
Volume Adjustment ................................................... 33
Quick Menu ................................................................. 34
On-Screen Menus Selection and Adjustment..... 35
2
Auto Programme Tuning............................................ 36
Manual Programme Tuning (In Digital Mode)..... 39
Manual Programme Tuning (In Analogue Mode) ... 41
Programme Edit ........................................................... 43
Booster(In Digital Mode)...........................................45
Software Update.......................................................... 46
Diagnostics ................................................................... 47
CI Information.............................................................. 48
Selecting the Programme List .................................. 49
Favourite Programme Setup...................................... 50
Input List........................................................................ 52
Input Label .................................................................... 53
................................................................. 54
AV Mode........................................................................ 57
Initializing (Reset to original factory settings) .....58
TO USE A USB DEVICE
When connecting a USB device.............................. 59
Photo List ...................................................................... 60
Music List........................................................................64
Movie List........................................................................67
DivX Registration Code ..............................................71
Deactivation...................................................................72
EPG (ELECTRONIC PROGRAMME
GUIDE) (IN DIGITAL MODE)
PICTURE CONTROL
Picture Size (Aspect Ratio) Control....................... 76
Picture Wizard................................................................78
Energy Saving ................................................................79
Preset Picture Settings
- Picture Mode-Preset............................................ 80
Manual Picture Adjustment
- Picture Mode-User option................................. 81
Picture Improvement Technology........................... 82
Expert Picture Control............................................... 83
Picture Reset................................................................. 86
Demo Mode.................................................................. 87
Mode Setting .................................................................88
TIME SETTING
Clock Setup ................................................................ 102
Auto On/ Off Time Setting .................................... 103
Sleep Timer Setting .................................................. 104
Alarm Setting (Except for 32LH202C)............... 104
CONTENTS
Switch on/off EPG ...................................................... 73
Select a Programme.................................................... 73
Button Function in NOW/NEXT Guide Mode ....... 74
Button Function in 8 Day Guide Mode..................74
Button Function in Date Change Mode................ 75
On-Screen Menu Language/Country Selection.... 100
Language Selection (In Digital Mode only)....... 101
PARENTAL CONTROL / RATINGS
Set Password & Lock System................................. 105
Block Programme ...................................................... 106
Parental Control (In Digital Mode only)............. 107
External Input Blocking.............................................108
Key Lock ...................................................................... 109
TELETEXT
Switch on/off .............................................................. 110
SIMPLE Text................................................................. 110
TOP Text....................................................................... 110
FASTEXT ....................................................................... 111
Special Teletext Functions........................................ 111
SOUND & LANGUAGE CONTROL
Auto Volume Leveler................................................... 89
Clear Voice II..................................................................90
Preset Sound Settings - Sound Mode................. 91
Sound Setting Adjustment -User Mode..............92
SRS TruSurround XT (Except for 32LH202C) ....... 92
Infinite Sound (Only 32LH202C)....................... 93
Balance ...................................................................... 93
DTV Audio setting (In Digital Mode only)........94
Selecting Digital Audio Out...................................95
Audio Reset ...............................................................96
Audio Description (In Digital Mode only)..........97
I/II
- Stereo/Dual Reception (In Analogue Mode Only).. 98
- NICAM Reception (In Analogue Mode Only)...... 99
- Speaker Sound Output Selection.................... 99
DIGITAL TELETEXT
Teletext within Digital Service................................. 112
Teletext in Digital Service......................................... 112
APPENDIX
Troubleshooting ...................................................... 113
Maintenance .......................................................... 115
Product Specifications.......................................... 116
IR codes.....................................................................117
External Control Device Setup ............................. 118
3
PREPARATION
FRONT PANEL CONTROLS
! NOTE
TV can be placed in standby mode in order to reduce the power consumption.
And TV should be switched off using the power switch on the TV if it will not be watched for some
time, as this will reduce energy consumption. (Except for 22/26/32/37/42 LH200H)
GThe energy consumed during use can be significantly reduced if the level of brightness of the picture is
reduced, and this will reduce the overall running cost.
G
G
PREPARATION
■
Image shown may differ from your TV.
(Only 19/22/26LH2***)
POWER INPUT MENU OK
INPUT MENU
OK
VOLUME
PROGRAMME
P
(Only 32/37/42LH2***)
P
PROGRAMME
VOLUME
OK
Remote Control Sensor
OK
MENU
MENU
INPUT
INPUT
POWER
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the TV is switched on.
4
Main Power Switch
(Except for 22/26/32/37/42 LH200H, 32LH202C)
H/P
BACK PANEL INFORMATION
19/22LH2***
A
Image shown may differ from your TV.
13
3
2
6
5
4
COMPONENT IN
USB IN
(RGB)
PREPARATION
1
RJP
INTERFACE
14
HDMI / DVI IN
STEREO
(8 )
SPEAKER
OUT
7
8
9
10
1
Power Cord Socket
This TV operates on an AC power. The voltage is
indicated on the Specifications page.(G p.116)
Never attempt to operate the TV on DC power.
2
USB IN Input
Connect USB storage device to this jack.
3
RGB/DVI Audio Input
Connect the audio from a PC or DTV.
4
OPTICAL DIGITAL AUDIO OUT
Connect digital audio to various types of equipment.
Connect to a Digital Audio Component.
Use an Optical audio cable.
5
6
H/P
VOLUME
CONTROL
RGB IN (PC)
Euro Scart Socket (AV)
Connect scart socket input or output from an
external device to these jacks.
11
ANTENNA IN
12
7
HDMI/DVI IN Input
Connect an HDMI signal to HDMI IN. Or DVI
(VIDEO) signal to HDMI/DVI port with DVI to
HDMI cable.
8
RGB IN Input
Connect the output from a PC.
9
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.
10
Component Input
Connect a component video/audio device to
these jacks.
11
SPEAKER OUTPUT(STEREO)
The phone socket for external speaker is on this jack.
12
Antenna Input
Connect
antenna or cable to this jack.
VOLUME
13
PCMCIA (Personal Computer Memory Card
International
Association) Card Slot
STEREO
(8 )
Insert the
CI Module to P C M C I A C A R D S L O T .
(This feature is not available in all countries.)
14
Headphone Socket
Plug the headphone into the headphone socket.
CONTROL
RJP INTERFACE
Connect control line (RJ45) for RJP(Remote Jack
pack)
5
PREPARATION
26/32/37/42LH2***
12
PREPARATION
1
13
4
3
2
(RGB)
VOLUME
CONTROL
5
RJP
INTERFACE
(Except for
32LH202C)
VOLUME
CONTROL
2
STEREO
(8 )
/DVI IN
STEREO
(8 )
1
14
SPEAKER
OUT
6
1
8
9
Power Cord Socket
This TV operates on an AC power. The voltage is
indicated on the Specifications page.(G p.116)
Never attempt to operate the TV on DC power.
2
RGB/DVI Audio Input
Connect the audio from a PC or DTV.
3
OPTICAL DIGITAL AUDIO OUT
Connect digital audio to various types of equipment.
Connect to a Digital Audio Component.
Use an Optical audio cable.
4
Euro Scart Socket (AV)
Connect scart socket input or output from an
external device to these jacks.
5
RJP INTERFACE (Except for 32LH202C)
Connect control line (RJ45) for RJP(Remote Jack
pack)
6
6
7
HDMI/DVI IN Input
Connect an HDMI signal to HDMI IN. Or DVI
(VIDEO) signal to HDMI/DVI port with DVI to
HDMI cable.
10
ANTENNA IN
H/P
11
7
RGB IN Input
Connect the output from a PC.
8
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.
9
Component Input
Connect a component video/audio device to
these jacks.
10
SPEAKER OUTPUT(STEREO)
The phone socket for external speaker is on this jack
11
Antenna Input
Connect antenna or cable to this jack.
12
USB IN Input
Connect USB storage device to this jack.
13
PCMCIA (Personal Computer Memory Card
International Association) Card Slot
Insert the CI Module to P C M C I A C A R D S L O T .
(This feature is not available in all countries.)
14
Headphone Socket
Plug the headphone into the headphone socket.
STAND INSTALLATION
■
Image shown may differ from your TV
When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can
tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion
of the tightening part of the bolt.
Only 19/22LH2***
1
Carefully place the TV screen side down on a cushioned
surface to protect the screen from damage.
1
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
2
Assemble the TV as shown.
2
Assemble the TV as shown.
3
PREPARATION
Only 26/32/37/42LH2***
Fix the 4 bolts securely using the holes in the
back of the TV.
Cover Base
7
PREPARATION
ATTACHING THE TV TO A DESK
(Only 26/32/37/42LH2***)
■
Image shown may differ from your TV.
The TV must be attached to desk so it cannot
be pulled in a forward/backward direction,
potentially causing injury or damaging the
product.
HOW TO SECURE THE POWER
CABLE (Only 26/32/37/42LH2***)
Secure the power cable with the Protective Bracket and the
bolt as shown. It will help prevent the power cable from being
removed by accident.
Bolt
PREPARATION
Protective Bracket
POSITIONING YOUR DISPLAY
(Only 19/22LH2***)
4-Screws
(not provided as parts of the product)
G
Screw: M5 x L (*L: Table depth + 8~10 mm)
ex) Table depth: 15mm, Screw: M5 x 25
■
Image shown may differ from your TV.
Adjust the position of the panel in various ways for
maximum comfort.
• Tilt range
■
12
0
0
3
Stand
KENSINGTON
SECURITY SYSTEM
This feature is not available for all models.
■
Desk
1-Screw (provided as parts of the product)
Stand
Desk
! WARNING
G
8
To prevent TV from falling over, the TV should
be securely attached to the floor/wall per
installation instructions. Tipping, shaking, or
rocking the machine may cause injury.
■
Image shown may differ from your TV.
The TV is equipped with a Kensington Security
System connector on the back panel. Connect the
Kensington Security System cable as shown below.
For the detailed installation and use of the Kensington
Security System, refer to the user’s guide provided
with the Kensington Security System.
For further information, contact http://www.kensington.com, the internet homepage of the Kensington
company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors.
NOTE
- The Kensington Security System is an optional accessory.
NOTES
a. If the TV feels cold to the touch, there may be a
small “flicker” when it is turned on.
This is normal, there is nothing wrong with TV.
b. Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue spots.
However, they have no adverse effect on the monitor's performance.
c. Avoid touching the LCD screen or holding your finger(s)
against it for long periods of time.
Doing so may produce some temporary distortion
effects on the screen.
CAREFUL INSTALLATION ADVICE
SWIVEL STAND
(Except for 19/22LH2***)
You should purchase necessary components to fix the TV
safety and secure to the wall on the market.
A Position the TV close to the wall to avoid the possibility
of it falling when pushed.
A The instructions shown below are a safer way to set up
the TV, by fixing it to the wall, avoiding the possibility of it
falling forwards if pulled. This will prevent the TV from
falling forward and causing injury. This will also prevent
the TV from damage. Ensure that children do not climb or
hang from the TV.
A
PREPARATION
2
2
Use the eye-bolts or TV brackets/bolts to fix the
product to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen then
bolts.)
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts on the wall.
Match the height of the bracket that is mounted on
the wall.
2
Image shown may differ from your TV.
After installing the TV, you can adjust the TV set
manually to the left or right direction by 20 degrees
to suit your viewing position.
1
1
1
■
HOW TO USE DUAL LOCK™
(This feature is not available
for all models.)
(Only 22/26/32/37/42 LH200H)
Fix the set-top box to the TV and use it when you want to.
1
After removing the protection paper from the
Dual Lock, stick it to the TV and the set-top
box as shown.
2
Attach the set-top box to the TV by pressing the
Velcro strips together.
3
3
Use a sturdy rope to tie the product for alignment. It
is safer to tie the rope so it becomes horizontal
between the wall and the product.
! NOTE
G
G
G
When moving the TV undo the cords first.
Use a platform or cabinet strong and large enough
to support the size and weight of the TV.
To use the TV safely make sure that the height of the
bracket on the wall and on the TV is the same.
9
PREPARATION
BACK COVER FOR WIRE ARRANGEMENT
■
Image shown may differ from your TV.
19/22LH2***
PREPARATION
1
2
26/32/37/42LH2***
Connect the cables as necessary.
To connect additional equipment, see the EXTERNAL
EQUIPMENT SETUP section.
1
Connect the cables as necessary.
To connect additional equipment, see the EXTERNAL
EQUIPMENT SETUP section.
2
Open the Cable Management Clip as shown.
Install the Cable Management Clip as shown.
Cable Management Clip
Cable Management Clip
3
3
Fit the Cable Management Clip as shown.
Fit the Cable Management Clip as shown.
How to remove the cable management
clip (19/22LH2***)
Hold the Cable Management Clip
with both hands and pull it backward.
! NOTE
G Do
not use the Cable Management Clip to lift the TV.
- If the TV is dropped, you may be injured or the TV may be damaged.
10
NOT USING THE DESK-TYPE STAND
■
Image shown may differ from your TV.
When installing the wall-mounted unit, use the protection cover.
19/22LH2***
26/32/37/42LH2***
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Loose the bolts from TV.
3
Detach the stand from TV.
4
Insert the P r o t e c t i o n C o v e r into the TV.
PREPARATION
Insert the P r o t e c t i o n
C o v e r into the TV until
clicking sound.
1
Protection Cover
Protection Cover
5
Fix the 4 bolts securely using the holes in the
back of the TV.
11
PREPARATION
A
A
The TV can be installed in various ways such as on
a wall, or on a desktop etc.
The TV is designed to be mounted horizontally.
WALL MOUNT: HORIZONTAL
INSTALLATION
We recommend the use of a LG Brand wall mounting
bracket when mounting the TV to a wall.
A We recommend that you purchase a wall mounting
bracket which supports VESA standard.
A LG recommends that wall mounting be performed by a
qualified professional installer.
A
EARTHING
PREPARATION
Ensure that you connect the earth wire to prevent
possible electric shock. If grounding methods are not
possible, have a qualified electrician install a separate
circuit breaker.
Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.
! NOTE
Power Supply
Should Install wall mount on a solid wall perpendicular to
the floor.
G Should use a special wall mount, if you want to install it to
ceiling or slanted wall.
G The surface that wall mount is to be mounted on should
be of sufficient strength to support the weight of TV set;
e.g. concrete, natural rock, brick and hollow block.
G Installing screw type and length depends on the wall
mount used. Further information, refer to the instructions
included with the mount.
G LG is not liable for any accidents or damage to property or
TV due to incorrect installation:
- Where a non-compliant VESA wall mount is used.
- Incorrect fastening of screws to surface which may cause
TV to fall and cause personal injury.
- Not following the recommended Installation method.
G
Circuit breaker
DESKTOP PEDESTALINSTALLATION
For adequate ventilation allow a clearance of 10 cm
all around the TV.
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
A
B
Model
19/22LH2***
26/32LH2***
37/42LH2***
12
VESA Standard
(A * B)
Screw Quantity
4
100 * 100 M4
4
200 * 100 M4
4
200 * 200 M6
EXTERNAL EQUIPMENT SETUP
■
To prevent damage do not connect to the mains outlet until all connections are made between the devices.
ANTENNA CONNECTION
■
■
For optimum picture quality, adjust antenna direction.
An antenna cable and converter are not supplied.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
VOLUME
CONTROL
STEREO
(8 )
ANTENNA IN
ANTENNA IN
VIDEO
L(MONO) AUDIO
R
VARIABLE AUDIO OUT
RF Coaxial Wire (75 Ω)
Outdoor
Antenna
(VHF, UHF)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
VIDEO
L(MONO) AUDIO
R
VARIABLE AUDIO OUT
Signal
Amplifier
VHF
■
■
ANTENNA
IN
VOLUME
CONTROL
UHF
Antenna
EXTERNAL EQUIPMENT SETUP
Wall
Antenna
Socket
STEREO
(8 )
ANTENNA IN
In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the
antenna as shown above.
If signal needs to be split for two TVs,use an antenna signal splitter for connection.
13
EXTERNAL EQUIPMENT SETUP
To avoid damaging any equipment, never plug in any power cord until you have finished connecting all equipment.
This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 26/32/37/42LH2*** models.
■
■
Image shown may differ from your TV.
■
HD RECEIVER SETUP
■
This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do receive
Digital signals from a digital set-top box or other digital external device, refer to the diagram as shown below.
Connecting with a Component cable
EXTERNAL EQUIPMENT SETUP
1
2
Connect the video outputs (Y, PB, PR) of the digital set
top box to the C O M P O N E N T I N V I D E O jacks on the
TV.
Connect the audio output of the digital set-top box to
the C O M P O N E N T I N A U D I O jacks on the TV.
2
/DVI IN
3
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
4
Select C o m p o n e n t input source using the I N P U T
button on the remote control.
G HDMI
Audio Supported format : Dolby Digital, PCM
Signal
Component
HDMI
480i/576i
O
X
480p/576p
O
O
720p/1080i
O
O
O
O
1080p
14
1
(50 Hz/ 60 Hz only) (24 Hz/ 30 Hz/ 50 Hz/ 60 Hz)
1
2
Connecting with an HDMI to DVI cable
1
Connect the digital set-top box to H D M I / D V I I N 1
jack on the TV.
Connect the audio output of the digital set-top box to
the A U D I O I N ( R G B / D V I ) jack on the TV.
3
Turn on the digital set-top box. (Refer to the owner’s
manual for the digital set-top box.)
4
/DVI IN
1
1
2
Select H D M I 1 input source using the I N P U T button
on the remote control.
EXTERNAL EQUIPMENT SETUP
2
2
Connecting a set-top box with an HDMI cable
1
Connect the digital set-top box to H D M I / D V I I N 1, H D M I 2
(Except for 19/22LH2***) jack on the TV.
2
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
3
Select H D M I 1, H D M I 2(Except for 19/22LH2***) input
source using the I N P U T button on the remote control.
! NOTE
2
/DVI IN
1
1
G Check
that your HDMI cable is version 1.3 or higher.
If the HDMI cables don’t support HDMI version 1.3, flickering or no screen display can result. Please use the latest
cables that support at least HDMI version 1.3.
15
EXTERNAL EQUIPMENT SETUP
DVD SETUP
Connecting with a Component cable
1
Connect the video outputs (Y, PB, PR) of the DVD to the
C O M P O N E N T I N V I D E O jacks on the TV.
1
EXTERNAL EQUIPMENT SETUP
2
Connect the audio outputs of the DVD to the
C O M P O N E N T I N A U D I O jacks on the TV.
3
Turn on the DVD player, insert a DVD.
2
/DVI IN
1
2
4
Select C o m p o n e n t input source using the I N P U T
button on the remote control.
5
Refer to the DVD player's manual for operating instructions.
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
16
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Connecting with a Euro Scart cable
(RGB)
RJP
INTERFACE
Connect the Euro scart socket of the DVD to the A V
Euro scart socket on the TV.
1
VOLUME
CONTROL
2
Turn on the DVD player, insert a DVD.
STEREO
(8 )
Select A V input source using the I N P U T button on the
remote control.
4
Refer to the DVD player's manual for operating
instructions.
1
Scart
AV
Output
Input
Video
O
Audio
O
RGB
O
AUDIO/
VIDEO
Video, Audio
Analogue TV, Digital TV
G
(R) AUDIO (L)
TV/DTV Out : Outputs analogue &
digital TV signals.
EXTERNAL EQUIPMENT SETUP
3
SPEAKER
OUT
! NOTE
G
Any Euro scart cable used must be signal shielded.
17
EXTERNAL EQUIPMENT SETUP
Connecting the HDMI cable
EXTERNAL EQUIPMENT SETUP
18
1
Connect the HDMI output of the DVD to the
H D M I / D V I I N 1, H D M I 2(Except for 19/22LH2***)
jack on the TV.
2
Select H D M I 1, H D M I 2(Except for 19/22LH2***) input
source using the I N P U T button on the remote control.
2
/DVI IN
3
1
Refer to the DVD player's manual for operating
instructions.
1
! NOTE
G The
TV can receive video and audio signals simultaneously
when using an HDMI cable.
G If the DVD does not support Auto HDMI, you must set the
output resolution appropriately.
G Check that your HDMI cable is version 1.3 or higher.
If the HDMI cables don’t support HDMI version 1.3, flickering or no screen display can result. Please use the latest
cables that support at least HDMI version 1.3.
VCR SETUP
■
To avoid picture noise (interference), allow adequate distance between the VCR and TV.
Connecting with a RF Cable
STEREO
(8 )
SPEAKER
OUT
ANT OUT
S-VIDEO
ANT IN
OUTPUT
SWITCH
VIDEO
L
R
1
ANTENNA IN
2
Wall Jack
EXTERNAL EQUIPMENT SETUP
VOLUME
CONTROL
Antenna
1
Connect the A N T O U T socket of the VCR to the A N T E N N A I N socket on the TV.
2
Connect the antenna cable to the A N T I N socket of the VCR.
3
Press the P L A Y button on the VCR and match the appropriate channel between the TV and VCR for
viewing.
VOLUME
CONTROL
STEREO
(8 )
19
EXTERNAL EQUIPMENT SETUP
Connecting with a Euro Scart cable
RJP
INTERFACE
(RGB)
Connect the Euro scart socket of the VCR to the A V
Euro scart socket on the TV.
1
VOLUME
CONTROL
2
Insert a video tape into the VCR and press PLAY on
the VCR. (Refer to the VCR owner’s manual.)
Select A V input source using the I N P U T button on
the remote control.
3
EXTERNAL EQUIPMENT SETUP
1
Scart
AV
Output
Input
Video
O
Audio
O
RGB
O
Video, Audio
Analogue TV, Digital TV
AUDIO/
VIDEO
G
! NOTE
G
20
STEREO
(8 )
SPEAKER
OUT
Any Euro scart cable used must be signal shielded.
(R) AUDIO (L)
TV/DTV Out : Outputs analogue &
digital TV signals.
INSERTION OF CI MODULE
- To view the encrypted (pay) services in digital TV
mode.
- This feature is not available in all countries.
1
For further information, see p.48.
Check this point as shown
and insert the CI Module.
! NOTE
G Check
if the CI module is inserted into the PCMCIA card slot in
the right direction. If the module is not inserted properly, this
can cause damage to the TV and the PCMCIA card slot.
H/P
EXTERNAL EQUIPMENT SETUP
Insert the CI Module to P C M C I A (Personal Computer
Memory Card International Association) C A R D S L O T
of TV as shown.
21
EXTERNAL EQUIPMENT SETUP
DIGITAL AUDIO OUT SETUP
Sending the TV’s audio signal to external audio equipment via the Digital Audio Output (Optical) port.
If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL
AUDIO OUT terminal on the back of TV to a Home Theater (or amp).
EXTERNAL EQUIPMENT SETUP
1
Connect one end of an optical cable to the TV Digital
Audio (Optical) Output port.
2
Connect the other end of the optical cable to the digital audio (Optical) input on the audio equipment.
3
Set the “TV Speaker option - Off ” in the AUDIO
menu.(Gp .93). Refer to the external audio equipment
instruction manual for operation.
(RGB)
1
2
CAUTION
G Do
not look into the optical output port. Looking at the
laser beam may damage your vision.
HEADPHONE SETUP
You can listen the sound through the headphone.
1
Plug the headphone into the headphone socket.
2
+ or
To adjust the headphone volume, press the
- button. If you press the MUTE button, the sound
from the headphone is switched off.
! NOTE
G
G
G
22
A U D I O menu items are disabled when connecting a headphone.
When changing A V M O D E with a headphone connected, the change is applied to video but not to audio.
Optical Digital Audio Out is not available when connecting a headphone.
SPEAKER OUTPUT SETUP
UP
Connect the external speaker to the S P E A K E R
O U T P U T( S T E R E O ) jack on the TV.
1
Control port for Speaker out
1
DOWN
RJP
INTERFACE
Method of Volume control port
Cable
Spec.
• Each Up/ Down pin is pulled
to 3.3V with CPU GPIO.
GND / Up / Down
• CPU detects sort - to - gnd
for volume control.
STEREO
(8 )
SPEAKER
OUT
GND
1
RIGHT
EXTERNAL EQUIPMENT SETUP
VOLUME
CONTROL
LEFT
GND
USB SETUP
1
1
Connect the USB device to the U S B I N jack on the TV.
2
After connecting the U S B I N jack, you use the U S B function. (G p .59)
23
EXTERNAL EQUIPMENT SETUP
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
Connecting with a D-sub 15 pin cable
EXTERNAL EQUIPMENT SETUP
1
Connect the RGB output of the PC to the R G B I N
( P C ) jack on the TV.
(RGB
2
2
Connect the PC audio output to the A U D I O I N
( R G B / D V I ) jack on the TV.
3
Turn on the PC and the TV
/DVI IN
1
2
4
1
Select R G B input source using the INPUT button on
the remote control.
AUDIO
24
RGB OUTPUT
Connecting with an HDMI to DVI cable
1
(RGB
Connect the PC audio output to the A U D I O I N
( R G B / D V I ) jack on the TV.
2
/DVI IN
3
Turn on the PC and the TV.
4
Select H D M I 1 input source using the INPUT button
on the remote control.
1
1
2
EXTERNAL EQUIPMENT SETUP
2
Connect the DVI output of the PC to the H D M I / D V I
I N 1 jack on the TV.
25
EXTERNAL EQUIPMENT SETUP
Supported Display Resolution
HDMI/DVI-DTV mode
RGB-PC, HDMI/DVI-PC mode
EXTERNAL EQUIPMENT SETUP
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
Resolution
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
720x400
31.468
70.08
720x480
31.469/31.5
59.94/60
640x480
31.469
59.94
720x576
31.25
50
800x600
37.879
60.31
1280x720
37.5
50
1920x1080
1024x768
48.363
60.00
44.96/45
59.94/60
1280x768
47.78
59.87
33.72/33.75
59.94/60
1360x768
47.72
59.80
28.125
50
1280x1024
63.595
60.00
26.97/27
23.97/24
33.716/33.75
29.976/30.00
56.25
50
67.43/67.5
59.94/60
Download PDF

advertising