LG | CRD-8483B | Owner's Manual | LG CRD-8483B Owner's manual

LG CRD-8483B Owner's manual
CD-ROM DRIVE
MODEL
:
CRD-8483B
OWNER'S MANUAL
BEDIENUNGSHANDBUCH
MODE D'EMPLOI
MANUALE D'USO
MANUAL DE USUARIO
To
enjoy fully
all the features and functions of your CD-ROM
carefully and completely.
Drive,
Please read this Owner 's Manual
Questo manuale include il
di
garanzia. (pagina
n.
tagliando
I-8)
website ; http://www.LGEservice.com
e-mail ; http://www.LGEservice.com/techsup.html
CAUTION
The laser used in the CD-ROM drive
:
Do not attempt to open the
can
damage
your eyes.
cover.
To reduce the risk of electric shock, do not
remove cover
(or back).
No user-serviceable parts inside.
Refer
This unit
English
uses
servicing
symbol
personnel.
:
of
performance
or
ser vice
qualified
CD-ROM discs
marked with this
Use of controls
to
other than those
procedures
specified
here in may result in hazardous radiation
exposure.
PRODUCT COMPLIES WITH DHHS
RULES 21 C.F.R. SUB-CHAPTER J,
IN EFFECT AT THE DATE OF MANUFACTURE.
WARNING
To reduce the risk of fire
:
do not expose this
Industry
Canada
This class B
or
electric shock,
appliance to
rain
moisture.
or
requirement
digital apparatus
meets all
requirements
of the Canadian
Interference-Causing Equipment
Regulations.
Cet
appareil numerique
de la classe B respecte toutes les
exigences du Reglement
sur
le materiel brouilleur du
Canada.
FCC COMPLIANCE STATEMENT
Note
:
This equipment has been tested and found to
comply with
the limits for
a
Class B digital device, pursuant to Part 15 of
the FCC Rules.
These limits are
reasonable
designed to provide
This equipment generates, uses, and
dance with the instructions, may
that interference will not
or
television
reception,
occur
which
to correct the interference
following
-
-
-
-
?
Reorient
in
can
a
harmful interference to radio communications. However, there is
particular
more
in
no
accor-
guarantee
installation. If this equipment does cause harmful interference to radio
be determined
by one or
installation.
by turning
the
equipment off
and on, the
user
is encouraged to try
of the
measures:
or
relocate the
Increase the
separation
Connect the equipment
Consult the dealer
Changes or
This
cause
protection against harmful interference in a residential
frequency energy and, if not installed and used
radiate radio
receiving
antenna.
between the
into
or an
an
equipment and
outlet
on a
receiver.
circuit different from that to which the receiver is connected.
Authorized Service Center for
help.
FCC WARNING
to
?
can
modifications not
expressly approved by the party responsible for compliance could void
the user's
operate the equipment.
This CD-ROM Drive is for
use
only with
UL listed
personal computers that
have installation instructions
installation of card cage accessory.
detailing
user
product
is manufactured to
comply
with the radio interference
89/336/EEC, 93/68/EEC and 73/23/EEC.
E-2
requirements of
EEC DIRECTIVE
authority
DECLARATION OF CONFORMITY
This device
is
subject
not
cause
complies with
following
to the
harmful
interference, and (2)
any interference received,
undesired operation.
Trade Name/Model
Responsible Party
Address
Part 15 of the FCC Rules.
two conditions
LG
:
including
or
Operation
this device may
this device must accept
:
(1)
interference that may
cause
Goldstar/CRD-8483B
LG Electronics U.S.A. Inc.
:
6133 N. River
:
Road, Suite
1100
(Riverway Plaza) Rosemont,
Mr. K.S.kim, Manager
Contact Person:
IL 60018
Tel. No. (847) 692-4500
Equipment Classification
Type of Product (EUT)
FCC Class B
:
Manufacturer
Peripheral Device(JBP)
CD-ROM Drive
:
:
LG Electronics lnc.
Address : 19-1,
Attention
:
Cheongho-Ri, Jinwuy-Myon
Pyungtaek-Shi, kyunggi-Do, 451-713
Mr. T.K.Lee General Manager
Korea
-
Multimedia Standards Team
We
hereby declare that the equipment bearing the
specified above was tested conforming to
number
trade and model
the
applicable FCC
possible, and
Rules under the most accurate measurement standards
that all the necessary steps have been taken and are in force to assure
that production units of the same equipment will continue to comply
with the Commission's
requirements.
E-3
Features
Features
[
E-IDE interface
[
48X-speed
[
75ms random
[
Intelligent
[
[
[
[
[
[
[
[
[
Max 7200KB/sec data transfer rate
access
time
128KB data
buffering system
(MPC spec.)
Motorized tray loading system
Horizontal/Vertical mounting support
Designed for internal mounting
Emergency eject support
Easy audio CD control button support
Supports Windows 95 & 98 Plug-and-Play
Multimedia PC MPC compliant
Small CPU bandwidth
Photo CD multisession
ATAPI
protocol
support
System Requirement*
[
IBM PC AT
[
[
[
[
[
or
compatible,
486 SX 25 processor
or higher
higher recommended).
640 Kb memory (16Mb or higher recommended).
A suitable free standard 51/4" internal drive bay.
MS-DOS version 3.1 or higher. (Windows 95 and above recommended).
31/2" 1.44 Mb Floppy Drive.
An existing IDE controller with an available cable connector or a new IDE
controller (recommended with IDE PIO Mode 4 capability) that you will need
(Pentium
133 Processor
or
to install.
*
Please note: certain software
playback) may require
acceptable results.
an
(i.e. particularly those including Video
considerably increased specification PC to give
E-4
Location and Function of Controls
Front View
COMPACT
1
2
4567
3
Back View
DIGITAL
AUDIO
ANALOG
AUDIO
DGRGL
INTERFACE
CSM
39
SLA
40
12
Supplied
POWER
12
3
4
+5
GND+12
5
Accessories
zOwner's Manual
zDevice
Driver(MS-DOS)
E-5
zAudio Cable
Front View
1.
Jack
Headphone
Standard 1/8"
2.
3.
Headphone
Adjusts the headphone
5.
jack
for
listening
to the audio
signal
from audio CDs.
sound level.
Disc Drawer
Accepts
4.
stereo
(3.5mm)
Volume Control
CD-ROM disc
a
on
its
tray.
Busy Indicator
The Busy Indicator lights during
initialization and data-read
operations.
Hole
Emergency Eject
Insert a paper clip
here to
eject
the drawer
manually
or
when there is
no
power.
6.
Button
Play/Skip
When
Audio CD is in the Disc Drawer,
an
audio CDs from the first track. If
playing
button will
7.
skip
pressing
an
this button will start
audio CD is
playing, pressing
this
to the next track.
Open/Close/Stop Button
pressed to open or close the CD tray.
If an audio CD is playing, pressing this button will stop it,
again will open the tray.
This button is
and
pressing
it
Back View
1.
You
2.
Audio
Digital
This is
Output Connector
digital audio output or Video CD output
connect this to a digital audio system or
a
can
Analog
Audio
The Audio
3.
Video CD Board.
Connector
Output
Output Connector
connects to
a
sound card.
Master/Slave/CSEL Jumper
These three
Slave,
4.
connector.
a
or
jumpers
are
used to set the CD-ROM Drive to either
Master,
Interface Connector
This
40-pin
connector is used to transfer data and control
ROM Drive and your PC.
5.
a
CSEL device.
Power-in Connector
Attach
a
power cable from the computer to this connector.
E-6
signals
between the CD-
Installing
Before
the Drive
the drive, turn off the
installing
system power. Follow the steps below
to
install the CD-ROM drive:
1.
Remove the cover from your computer system. Refer
computer for details about removing the cover.
Insert the CD-ROM drive unit into
2.
CD-ROM drive to the drive
3.
Connect the
4-pin
bay
a
free 5.25-inch drive
rails with the
power cable and
to manual for the
40-pin
mounting
bay.
Secure the
screws
(supplied).
IDE interface cable to the back of
the CD-ROM drive.
POWER
+12
+5 GND
INTERFACE
DIGITAL
AUDIO
12
ANALOG
AUDIO
DGGLCSM39
R
Power Cable
40
SLA
Audio Cable
Red
IDE cable
Notes: If there is
to
purchase
The red
a
edge
no
Strip
spare power cable available in the computer, you will have
splitter
cable of
of the IDE cable
a
suitable
type.
corresponds to pin
1 of the IDE interface
on
the
CD-ROM drive.
Please Note:
an
IDE cable is not
supplied
and may be
required
to be
purchased
separately.
If the
with
computer is using
an
SoundBlasterⓒ
it
a
sound card, the drive is connected to the sound card
audio cable. This CD-ROM drive is
maybe
compatible
supplied
with
a
Creative Labs
audio lead, if this is not suitable for your sound card,
necessary for you to
purchase
a
suitable lead from your retailer. Refer
to the manual for the sound card for detailed information
E-7
regarding
connection.
4.
Adjust
the Master/Slave
jumpers
the back of the CD-ROM drive
on
as
necessary.
Connect the CD-ROM drive to the IDE
the hard drive will be in
There
operating system.
Primary
are
two
IDE
ports of your motherboard. In general,
port and Master device for booting the
alternate connection for CD-ROM
possible
drive installation.
A)
When
using
a
Primary
IDE
port
If you need to connect your CD-ROM drive to the
CD-ROM drive should be set to Slave
same
Primary
IDE
port, the
position.
Master drive
(Booting
DIGITAL
UDIO
DG
hard
disk)
ANAL
UDI
R
GL
CE
1
2
Primary
POWER
+5
GND
+12
connector
Slave drive
(CD-ROM drive)
B)
When
You
can
Master
using
a
Secondary
IDE
port
also connect CD-ROM drive to the
Secondary
IDE
port and
set to
position.
Master drive
(Booting
hard
Master drive
disk)
(CD-ROM drive)
DIGITAL
UDIO
AN
LOG
UDIO
DG
RGL
CSM
39
INTERFACE
0
1
2
POWER
+5 GND +12
Slave drive
DIGIT
AL
DIO
U
DG
ANLOG
UDIO
(Other
R
GL
E
1
2
POWER
+5+
GND
1
2
IDE
drive)
Motherboard
Primary
5.
Secondary
connector
When the installation of the drive unit is
complete, replace
the
cover.
6.
Reconnect the
computer power cord and
turn
E-8
on
the
computer.
computer
connector
Device Drivers
When
using
Windows 98/95
or
Window NT Workstation Ver. 4.0, the
installation of any software driver
or
special
device is not
required.
This CD-ROM drive is
These drivers
Drivers for other
they usually
supplied with MS-DOS drivers on a 31/2-inch floppy disk.
required to use the CD-ROM drive in DOS and Windows 3.1.
are
Operating Systems are not normally required or available as
an generic IDE, E-IDE/ATAPI CD-ROM driver built in; Windows
and higher and OS/2 Warp 3.0 are such examples.
have
95, 98, NT 3.51
If it is necessary to edit any file
disk, then edit the
PC to
ensure
Running
the
manually,
first make
backup
a
copy
on a
floppy
it to your hard drive, exit, and re-boot the
original file,
change will be implemented.
save
the Install
Program (MS-DOS Installation)
4.
appropriate drive with DOS booting.
floppy
by typing A: or B: at the DOS prompt, as appropriate.
the
word
INSTALL
and press [ENTER].
Type
The INSTALL program will begin loading. When loading is complete, the
5.
Follow the instructions
6.
When installation is
1.
2.
3.
Insert the diskette into the
Go to the
drive
INSTALL program identification will appear
on screen.
on screen.
complete,
remove
the diskette and reboot your PC.
For Windows 98/95 Users
[
In order to
?
?
[
If
normal drive
operation, please
check the
following:
displayed
[control panels]-[system]-[device manager]-[CD-ROM]
32-bit is displayed in
[control panels]-[system]-[performance]
the drive is not recognized by your computer, please check the following
ensure
The drive is
in
items.
?
If
displayed on the IDE controller in [control panels][system]-[device manager]-[harddisk controller], you will need to contact
your PC's manufacturer or the motherboard's manufacturer and get the appropria
indicator is
ate IDE controller driver.
[
Run ADD NEW HARDWARE in Control Panel to let PC search
device.
E-9
again
for
new
For Windows NT Workstation Ver. 4.0 Users
[
In order to
?
normal drive operation, please check the following:
displayed on the IDE controller in
[control panels] [SCSI adapter] [devices]
the drive is not recognized by your computer, please check the following
ensure
The drive is
-
[
If
-
items.
?
If a
indicator is displayed on
[SCSI adapter]-[devices], you will
or
the IDE controller in
[control panels]-
need to contact your PC's manufacturer
the motherboard's manufacturer and
get the appropriate IDE controller
driver.
Emergency Eject
This drive has
function that allows the CD to be
a
becomes necessary in
an
emergency, such
outage. Follow this procedure in such
NOTE: Don't
1)
2)
use
this feature
except in
as
ejected manually
failure of the drive
if this
or a
power
a case.
an
emergency.
Turn the power to OFF.
Poke
a
fine-tipped object (such
as a
straightened heavy duty
paper
clip)
the small hole at the front. The front door will pop open and the disk
partway
into
tray will
out.
COM PACT
3)
Pull the front door to open it all the way, then
thumb and
forefinger
NOTE: This feature is
excessively
will
cause
a
and
last
gently pull
measure
it
grip the
straight out.
to be used
malfunction.
E-10
only
in
an
disc
tray between
emergency.
Using
it
come
Installation, Usage and Handling Precautions
[
lnstallation
Avoid
-
-
-
a
location
subject
to
:
mechanical vibration
-
excessive vibration
or a
sudden
jolt
to the drive may
malfunction.
cause a
-
in
direct
sunlight
Operation
During operation,
-
[
placing the drive
high humidity
high temperature
Avoid
exposing
cause
condensation to collect inside the drive.
the drive to sudden
changes
in
temperature. This may
Do not use damaged, cracked, or warped discs.
Transportation
Always remove the disc before moving the drive.
-
[
-
Troubleshooting
*
When the CD-ROM drive does not work with the hard disk drive in
primary
IDE channel.
(SOLUTION)
1.
Check the CD-ROM drive Master/Slave
Jumper setting.
The CD-ROM drive must be set to the Slave mode.
2.
3.
Check to be
sure your hard disk Interface type is IDE type.
Check your hard disk Master/Slave Jumper setting.
Some old-version IDE type hard disks were set to Master Only mode.
In that case, contact your hard disk company and
jumper setting to master mode.
4.
change
your hard disk
If the CD-ROM drive does not work with above methods, you may need a
IDE card. If you use the secondary IDE card, you should set the
secondary
CD-ROM drive
device you
*
jumper to the
connecting to
are
master mode if the CD-ROM drive is the first
the
secondary
IDE card.
When the CD-ROM drive does not install in OS/2 warp.
(SOLUTION)
1.
Select NON-LISTED IDE CD.
*
CD-ROM drive is not
present in Windows
3.1
or
3.11
or
DOSSHELL.
(SOLUTION)
1.
When the WIN
or
DOSSHELL command lines
are present in your
that the MSCDEX.EXE command line appears
the DOSSHELL command lines.
AUTOEXEC.BAT, make
before the WIN
NOTE:
For
more
or
sure
information, consult the README.TXT file of the supplied Setup
Diskette.
E-11
Specifications
General
Data
Capacity
553
Mbytes (mode 1),
Disc Diameter
12 cm/8
Rotational
Approx. 10,500
Speed
635
Mbytes (mode 2)
cm
rpm
(inner
max
speed)
Performance
Interface
E-IDE
Supported System
IBM PC-AT
Transfer rate
Sustained Data Transfer Rate=Max
Access Time
Random 75
MTBF
125,000 Power On Hours (Duty Cycle 10%)
Buffer size
128
Compatible
or
7,200Kbytes/sec
Typical
ms
Kbytes
Error Rate
ECC
1 block/1015 bits
(48x)
(48x)
2,048 bytes/block (Mode1 & Mode2 Form1)
2,340, 2,336 bytes/block (Mode2)
2,324 bytes/block (Mode2 Form2)
2,352 bytes/block (CD-DA)
on
ECC off
1 block/1012 bits
User Data/Block
Supported
Audio
Disc
CD-DA, CD-ROM, CD-ROM XA-READY, Photo-CD
CD-Plus/CD-Extra, Mixed CD, CD-RW
Specifications
Frequency Response
20Hz-20KHz±3dB
S/NRatio
75 dB
THD
0.05%at1KHz
Channel
75dBat1KHz
Separation
Headphone Level
Line Output Level
Line Output Jack
Headphone Jack
0.60 Vrms
(33Ω)
0.70 Vrms ± 20%
(47kΩ)
(Rear)
(Front)
4-Pin terminal
ø
3.5
mm
Environment
5-45°C
Temperature
Power
Requirements
12V±5%
Ripple
<
100m
Vpp
5V±5%
Ripple
NOTE:
<
100m
Vpp
Specifications
are
1.5A
(Maximum)
0.9A
(Maximum)
subject
to
change
without notice for
E-12
improvement.
LG Electronics U.S.A., Inc.
ENHACE
D
CD-ROM DRIVE
English.........Page
CH01
E-2
~
Deutsch .........Seite D-1
Francais .........Page
~
I-1
CLASS 1
LASER PRODUCT
KLASSE 1
LASER PRODUKT
LUOKAN 1
LASER LAITE
KLASS 1
LASER APPARAT
D-7
~
F-1
Italiano............Pagina
E-12
F-7
~
I-9
Copyrightⓒ
Spanish.......Pagina
S-1
S-7
~
2000 LG Electronics Inc.
LG Electronics U.S.A. Inc.
1000
Sylvan
Ave.
Englewood
Cliffs
NJ 07632 U.S.A.
LG Electronics Canada lnc.
235
Superior Blvd, Mississauga
Ontario, Canada
LG Electronics Deutschland GMBH
Jakob-Kaiser-Straße 12,
D-47677 Willich,
Germany
LG Electronics U. K. Ltd.
LG House, 264 Bath Road,
Slough Berkshire SL1 4DT
United
Kingdom
Goldstar France SARL
12, Rue Lech Walesa-Z.I. Pariest
77185
Lognes,
France
LG Electronics Italia S.P.A.
Centro Direzione "IL Quadrate" Via
20090
LG Electronics
Espana
Adva, De Europa,
28108 Alcovendas
P/NO
:
3828HM1021A
Modigliani,
Segrate (MI) Italy
21
(Madrid) Spain
Printed in Korea
(M-K)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising