LG | CRD-8522B | Owner's Manual | LG CRD-8522B Owner's manual

LG CRD-8522B Owner's manual
CD-ROM DRIVE
MODEL
:
CRD-8522B
OWNER'S MANUAL
BEDIENUNGSHANDBUCH
MODE D'EMPLOI
MANUALE D'USO
MANUAL DE USUARIO
To
enjoy fully
all the features and functions of your CD-ROM
carefully and completely.
Drive,
Please read this Owner's Manual
Questo manuale include il
di
garanzia. (pagina
n.
tagliando
I-8)
website ; http://www.LGEservice.com
e-mail ; http://www.LGEservice.com/techsup.html
AUTION
The laser used in the CD-ROM drive
:
Do not attempt to open the
can
damage
To reduce the risk of electric shock, do not
No user-serviceable parts inside.
Refer servicing to qualified ser vice
This unit
English
uses
or
remove cover
(or back).
personnel.
COMPACT
CD-ROM discs
marked with this
Use of controls
your eyes.
cover.
symbol:
of
performance
procedures
other than those
specified
here in may result in hazardous radiation
exposure.
PRODUCT COMPLIES WITH DHHS
RULES 21 C.F.R. SUB-CHAPTER J,
IN EFFECT AT THE DATE OF MANUFACTURE.
WARNING
To reduce the risk of fire
:
do not expose this
Canada
Industry
This class B
or
electric shock,
appliance
to rain
or
moisture
requirement
meets all
digital apparatus
requirements of
the Canadian
Interference-Causing Equipment
Regulations.
Cet
appareil numerique
de la classe B respecte toutes les
exigences
du
Reglement
sur
le materiel brouilleur du
Canada.
FCC COMPLIANCE STATEMENT
Note
:
This equipment has been tested and found to
comply with the
limits for
a
Class B digital device, pursuant to Part 15
of the FCC Rules.
These limits are
designed
reasonable
provide
to
This equipment generates, uses, and
can
protection against harmful interference in a residential
frequency energy and, if not installed and used
radiate radio
installation.
in
accor-
dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio
to
or
try to
television
following
-
-
-
-
?
?
This
Reorient
reception,
which
correct the interference
by
can
be determined
one or more
by turning
the
equipment off
and on, the
user
is encouraged
of the
measures:
or
relocate the
receiving
Increase the
separation
Connect the equipment
Consult the dealer
antenna.
between the
into
or an
an
equipment and
outlet
on a
receiver.
circuit different from that to which the receiver is connected.
Authorized Service Center for
help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the
ity to operate the equipment.
This CD-ROM Drive is for use only with UL listed personal computers that have installation instructions
detailing user installation of card cage accessory.
product
is manufactured to
comply
with the radio interference
89/336/EEC, 93/68/EEC and 73/23/EEC.
E-2
requirements
user's author-
of EEC DIRECTIVE
DECLARATION OF CONFORMITY
This device
is
subject
complies with
following
to the
Part 15 of the FCC Rules.
two conditions
Operation
this device may
this device must accept
(1)
interference, and (2)
interference
received, including interference that may
any
not
cause
undesired
harmful
:
cause
operation.
Trade Name/Model
Responsible Party
Address
LG
:
or
Goldstar/CRD-8522B
LG Electronics U.S.A.
:
Inc., Chicago office
6133 North River RD Suite 1100
:
Rosemont, IL. 60018, U.S.A.
Contact Person:
Mr. P. H.
Byun,
General
Manager
Tel. No. (847) 993-4529
Equipment Classification
Type of Product (EUT)
FCC Class B
:
Manufacturer
Peripheral Device(JBP)
CD-ROM Drive
:
:
LG Electronics lnc.
Address : 19-1,
Attention
:
Cheongho-Ri, Jinwuy-Myon
Pyungtaek-Shi, kyunggi-Do, 451-713
Mr. T.K.Lee General Manager
Korea
-
Multimedia Standards Team
We
hereby declare that the equipment bearing the
specified above was tested conforming to
number
trade and model
the
applicable FCC
possible, and
Rules under the most accurate measurement standards
that all the necessary steps have been taken and are in force to assure
that production units of the same equipment will continue to comply
with the Commission's
requirements.
E-3
English
Features
Features
[
E-IDE interface
[
52X-speed
[
80ms random
[
[
[
[
[
[
[
[
[
[
Intelligent
Max 7800KB/sec data transfer rate
access
time
128KB data
buffering system
(MPC spec.)
Motorized tray loading system
Horizontal/Vertical mounting support
Designed for internal mounting
Emergency eject support
Easy audio CD control button support
Supports Windows 95, 98 & 2000 Plug-and-Play
Multimedia PC MPC compliant
Small CPU bandwidth
Photo CD multisession
ATAPI
protocol
support
System Requirement*
[
IBM PC AT
[
[
[
[
[
compatible,
486 SX 25 processor
higher
higher recommended).
640 Kb memory (16Mb or higher recommended).
A suitable free standard 51/4" internal drive bay.
MS-DOS version 3.1 or higher. (Windows 95 and above recommended).
31/2" 1.44 Mb Floppy Drive.
An existing IDE controller with an available cable connector or a new IDE
controller (recommended with IDE PIO Mode 4 capability) that you will need
(Pentium
or
133 Processor
or
or
to install.
*
Please note: certain software
playback) may require
acceptable results.
an
(i.e. particularly those including Video
considerably increased specification PC to give
E-4
Location and Function of Controls
Front View
COMPACT
1
2
4567
3
Back View
12
Supplied
3
4
5
Accessories
zOwner's Manual
zDevice
Driver(MS-DOS)
E-5
zAudio Cable
Front View
1.
Jack
Headphone
Standard 1/8"
Headphone
Adjusts the headphone
3.
Disc Drawer
Accepts
4.
5.
stereo
(3.5mm)
jack
for
listening
to the audio
signal
from audio CDs.
Volume Control
2.
sound level.
CD-ROM disc
a
on
its
tray.
Busy Indicator
The Busy Indicator lights during
initialization and data-read
Emergency Eject Hole
Insert a paper clip here
the drawer
to
eject
manually
or
operations.
when there is
no
power.
6.
Play/Skip
When
Button
Audio CD is in the Disc Drawer, pressing this button will start
audio CDs from the first track. If an audio CD is playing, pressing this
an
playing
button will
7.
skip
to the next track.
Open/Close/Stop Button
pressed to open or close the CD tray.
If an audio CD is playing, pressing this button will stop it,
again will open the tray.
This button is
and
pressing
it
Back View
1.
You
2.
Audio
Digital
This is
Output Connector
digital audio output or Video CD output
connect this to a digital audio system or
a
can
Analog
Output Connector
Output Connector connects to
a
sound card.
Master/Slave/CSEL Jumper
These three
Slave,
4.
Video CD Board.
Audio
The Audio
3.
connector.
a
or
jumpers
are
used to set the CD-ROM Drive to either
Master,
Interface Connector
This
40-pin
connector is used to transfer data and control
ROM Drive and your PC.
5.
a
CSEL device.
Power-in Connector
Attach
a
power cable from the computer to this connector.
E-6
signals
between the CD-
Installing
Before
the Drive
the drive, turn off the
installing
system power. Follow the steps below
to
install the CD-ROM drive:
1.
2.
Remove the cover from your computer system. Refer
computer for details about removing the cover.
Insert the CD-ROM drive unit into
CD-ROM drive to the drive
3.
Connect the
bay
a
free 5.25-inch drive
rails with the
power cable and
the CD-ROM drive.
4-pin
to manual for the
40-pin
mounting
bay.
Secure the
screws
(supplied).
IDE interface cable to the back of
Power Cable
Audio Cable
Red
Strip
IDE cable
Notes: If there is
to
purchase
The red
a
edge
no
spare power cable available in the computer, you will have
splitter
cable of
of the IDE cable
a
suitable
type.
corresponds to pin
1 of the IDE interface
on
the
CD-ROM drive.
Please Note:
an
IDE cable is not
supplied
and may be
required
to be
purchased
separately.
If the
with
computer is using
an
SoundBlasterⓒ
it
a
sound card, the drive is connected to the sound card
audio cable. This CD-ROM drive is
maybe
compatible
supplied
with
a
Creative Labs
audio lead, if this is not suitable for your sound card,
necessary for you to
purchase
a
suitable lead from your retailer. Refer
to the manual for the sound card for detailed information
E-7
regarding
connection.
Features
4.
Adjust
the Master/Slave
jumpers
the back of the CD-ROM drive
on
as
necessary.
Connect the CD-ROM drive to the IDE ports of your motherboard. In general,
the hard drive will be in Primary IDE port and Master device for booting the
operating system.
There
are
two
alternate connection for CD-ROM
possible
drive installation.
A)
When
using
a
Primary
IDE
port
If you need to connect your CD-ROM drive to the
CD-ROM drive should be set to Slave position.
same
Primary
IDE
port, the
Master drive
(Booting
DGITL
UDIO
DG
hard
disk)
ANL
AUD
R GL
CE
1
2
Primary
POWER
+5GND+12
connector
Slave drive
(CD-ROM drive)
B)
When
You
can
Master
using
a
Secondary
IDE
port
also connect CD-ROM drive to the
Secondary
IDE
port and
set to
position.
Master drive
(Booting
hard
Master drive
disk)
DGITL
UDIO
(CD-ROM drive)
ANALOG
AUDIO
DG R
GL
CSM
39
NTERFACE
0
1
2
POWER
+5GND +12
Slave drive
DGITL
UDIO
ANALO
UDIO
DG
(Other
R GL
1
2
POWER
+5GND +12
IDE
drive)
Motherboard
Primary
5.
Secondary
connector
When the installation of the drive unit is
complete, replace
the
cover.
6.
Reconnect the
computer power cord and
turn
E-8
on
the
computer.
computer
connector
Device Drivers
When
using
Windows 95/98/2000
installation of any software driver
or
or
Window NT Workstation Ver.
special
device is not
4.0, the
required.
This CD-ROM drive is
disk.
These drivers
supplied with MS-DOS drivers on a 31/2-inch floppy
required to use the CD-ROM drive in DOS and Windows
3.1.
are
Drivers for other
Operating Systems are not normally required or available as
an generic IDE, E-IDE/ATAPI CD-ROM driver built in; Windows
95, 98, 2000, NT 3.51 and higher and OS/2 Warp 3.0 are such examples.
they usually
have
If it is necessary to edit any file
disk, then edit the original file,
PC to
ensure
the
Running
change
manually,
save
will be
the Install
2.
Insert the driver diskette into the
5.
6.
backup
copy
floppy
on a
Program (MS-DOS Installation)
Boot to the DOS
4.
a
drive, exit, and re-boot the
implemented.
1.
3.
first make
it to your hard
prompt.
appropriate drive.
by typing A: or B: at the DOS prompt, as appropriate.
Type the word INSTALL and [Enter].
The Install program will begin loading and you will prompted to accept the default directory of C:\DVDROM press [Enter] to accept (suggested) or edit the path then press [Enter].
When installation is complete, remove the diskette and reboot your PC.
Go to the
(Note:
floppy
drive
You must have
a
Config.sys
and
an
Autoexec.bat file
on
for the install program to add the necessary command
your hard drive
lines.)
For Windows 98/95 Users
[
In order to
?
?
[
If
normal drive operation, please check the following:
displayed in
[control panels]-[system]-[device manager]-[CD-ROM]
32-bit is displayed in
[control panels]-[system]-[performance]
the drive is not recognized by your computer, please check the following
ensure
The drive is
items.
?
If
a
indicator is
displayed
on
the IDE controller in
[system]-[device manager]-[harddisk controller],
your PC's manufacturer
or
[control panels]-
you will need to contact
the motherboard's manufacturer and
get
the
appropriate
IDE controller driver.
[
Run ADD NEW HARDWARE in Control Panel to let PC search
device.
E-9
again
for
new
For Windows NT Workstation Ver. 4.0 Users
[
In order to
?
normal drive operation, please check the following:
displayed on the IDE controller in
[control panels] [SCSI adapter] [devices]
the drive is not recognized by your computer, please check the following
ensure
The drive is
-
[
If
-
items.
?
If a
indicator is displayed on
[SCSI adapter]-[devices], you will
or
the IDE controller in
[control panels]-
need to contact your PC's manufacturer
the motherboard's manufacturer and
get the appropriate IDE controller
driver.
Emergency Eject
This drive has
a
function that allows the CD to be
ejected manually
becomes necessary in an emergency, such as failure of the drive
outage. Follow this procedure in such a case.
NOTE: Don't
1)
2)
this feature
except in
an
power
emergency.
Turn the power to OFF.
Poke a fine-tipped object
(such as a straightened heavy duty paper clip) into
the small hole at the front. The front door will pop open and the disk tray will
partway
3)
use
if this
or a
out.
Pull the front door to open it all the way, then grip the disc
forefinger and gently pull it straight out.
tray between
thumb and
NOTE: This feature is
excessively
will
cause
a
last
measure
to be used
malfunction.
E-10
only
in
an
emergency.
Using
it
come
Installation, Usage and Handling Precautions
[
lnstallation
Avoid
-
-
-
a
location
subject
to
:
mechanical vibration
excessive vibration
-
cause a
-
in
direct
sunlight
Operation
During operation,
-
[
placing the drive
high humidity
high temperature
or a
sudden
jolt
to the drive may
malfunction.
Avoid
exposing
cause
condensation to collect inside the drive.
the drive to sudden
changes
in
temperature. This may
Do not use damaged, cracked, or warped discs.
Transportation
Always remove the disc before moving the drive.
-
[
-
Troubleshooting
*
When the CD-ROM drive does not work with the hard disk drive in
primary
IDE channel.
(SOLUTION)
1.
Check the CD-ROM drive Master/Slave
Jumper setting.
The CD-ROM drive must be set to the Slave mode.
2.
3.
Check to be
sure your hard disk Interface type is IDE type.
Check your hard disk Master/Slave Jumper setting.
Some old-version IDE type hard disks were set to Master Only mode.
In that case, contact your hard disk company and
to master mode.
change
your hard disk
jumper setting
4.
If the CD-ROM drive does not work with above
methods, you may need a
IDE card. If you use the secondary IDE card, you should set the
CD-ROM drive jumper to the master mode if the CD-ROM drive is the first
secondary
device you
*
are
connecting
to the
secondary
IDE card.
When the CD-ROM drive does not install in OS/2 warp.
(SOLUTION)
1.
Select NON-LISTED IDE CD.
*
CD-ROM drive is not
present in Windows
3.1
or
3.11
or
DOSSHELL.
(SOLUTION)
1.
When the WIN
or
DOSSHELL command lines
are present in your
that the MSCDEX.EXE command line appears
the DOSSHELL command lines.
AUTOEXEC.BAT, make
before the WIN
NOTE:
For
more
or
sure
information, consult the README.TXT file of the supplied Setup Diskette.
E-11
Specifications
General
Data
Capacity
553
Mbytes (mode 1),
Disc Diameter
12 cm/8
Rotational
Approx. 10,800
Speed
635
Mbytes (mode 2)
cm
rpm
(inner
max
speed)
Performance
Interface
E-IDE
Supported System
IBM PC-AT or
Transfer rate
Sustained Data Transfer Rate=Max
Access Time
Random 80
MTBF
125,000 Power On Hours (Duty Cycle 10%)
Buffer size
128
Compatible
ms
7,800Kbytes/sec
Typical
Kbytes
Error Rate
ECC
1 block/1015 bits
(52x)
(52x)
2,048 bytes/block (Mode1 & Mode2 Form1)
2,340, 2,336 bytes/block (Mode2)
2,324 bytes/block (Mode2 Form2)
2,352 bytes/block (CD-DA)
on
ECC off
1 block/1012 bits
User Data/Block
Supported
Audio
Disc
CD-DA, CD-ROM, CD-ROM XA-READY, Photo-CD
CD-Plus/CD-Extra, Mixed CD, CD-RW
Specifications
20Hz-20KHz±3dB
Frequency Response
S/NRatio
75 dB
THD
0.05%at1KHz
75dBat1KHz
Channel
Separation
Headphone Level
Line Output Level
Line Output Jack
Headphone Jack
0.70 Vrms
(33Ω)
0.75 Vrms ± 10%
(47kΩ)
(Rear)
(Front)
4-Pin terminal
ø
3.5
mm
Environment
Temperature
Power
5-45°C
Requirements
12V±5%
Ripple
<
100m
Vpp
1.5A
(Maximum)
0.9A
(Maximum)
5V±5%
Ripple
NOTE:
<
100m
Vpp
Specifications
are
subject
to
change
without notice for
E-12
improvement.
*
ENHANCE
CD-ROM DRIVE
D
CH01
English
Deutsch
CLASS 1
LASER PRODUCT
KLASSE 1
LASER PRODUKT
LUOKAN 1
LASER LAITE
KLASS 1
LASER APPARAT
Francais
Copyrightⓒ
LG Electronics Inc.
2000
LG Electronics U.S.A. Inc.
Italiano
1000
Ave.
Sylvan
Englewood
Cliffs
NJ 07632 U.S.A.
LG Electronics Canada Inc.
235
Spanish
Superior Blvd, Mississauga
Ontario, Canada
LG Electronics Deutschland GMBH
Jakob-Kaiser-Straße 12,
D-47677 Willich,
Germany
LG Electronics U. K. Ltd.
LG House, 264 Bath Road,
Slough Berkshire SL1 4DT
United
Kingdom
Goldstar France SARL
12, Rue Lech Walesa-Z.I. Pariest
77185
Lognes,
France
LG Electronics Italia S.P.A.
Centro Direzione "IL Quadrate" Via
20090
Modigliani,
Segrate (MI) Italy
LG Electronics
Espana
Adva, De Europa,
28108 Alcovendas
P/NO
:
3828HM1026A
21
(Madrid) Spain
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising