OWNER'S MANUAL Model : LB-H0852QC LB-H0750QC IMPORTANT Please read through this manual. It contains valuable information about your air conditioner. This manual may help save time and money by explaining proper product maintenance and preventing improper use. PRECAUTIONS Pay close attention to precautions in order to prevent potential hazards and damage from misuse or improper installation. LG is not responsible for any damages caused by misuse of the product. ENGLISH LG Ceiling Duct-Type Air Conditioner LG Ceiling Duct-Type Air Conditioner Owner's Manual TABLE OF CONTENTS F or Your Records Write the model and serial numbers here: Model # Serial # 1. Safety Precautions Also note down the following : 2. Operating Instructions Dealer's Name 3. Care and Maintenance Date Purchased 4. Before you call for service R ead This Manual Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all. CAUTION • Contact the authorized service technician for repair or maintenance of this unit. • Contact the installer for installation of this unit. • The air conditioner is not intended for use by young children or invalids without supervision. • Young children should be supervised to ensure that they do not play with the air conditioner. • When the power cord is to be replaced, replacement work shall be performed by authorized personnel only. • Installation work must be performed in accordance with the national wiring standards by authorized personnel only. 2 Safety Precautions Precautions Incorrect operation due to ignoring instructions will cause harm or damage, the seriousness of which is indicated by the following symbols. WARNING This symbol shows the possibility of death or serious injury. CAUTION This symbol indicates the possibility of injury or damage to property. ENGLISH To prevent injury and property damage, follow these instructions. Never Do This Always Do This Installation precautions WARNING WARNING n Do not install, remove and reinstall the unit by yourself. • Improper installation will cause water leakage, electrical shock, or fire. Please consult authorized dealer or specialist for the installation work. Please note fault caused by improper installation is not covered by warranty. • Unit must be installed in an easily accessible area. Any additional cost required to hire a special equipment to service the unit will be the responsibility of the customer. 3 4 ENGLISH 5 6 ENGLISH 7 8 Operating Instructions Operating Instructions ENGLISH Name and Function of Remote Controller Remote Controller OPERATION SET TEMP COMP1 COMP2 88 Room Temp OR MN FAN SPEED HIGH SUB FUNCTION LP 12 HP 12 1 Out door Filter °C Time Timer Operation unit Sun Mon Tue Program set Wed Thu Fri Sat On Off Set no. Time 01 03 05 07 09 11 13 15 17 19 21 23 3 2 7 8 10 11 12 Timer Clear Filter Program Week Holiday 9 MANUAL 4 13 5 COMP SET Hour Min 6 15 RESET 14 1 Operation display 8 Clear Button Displays the operation conditions. Used to cancel the different program settings. 2 On/Off Button 9 Timer Set Button Used to set the airconditioner ON/OFF at particular time which depends upon whether machine is On or Off. Operation starts when this button is pressed, and stops when the button is pressed again. 3 Set Temperature Button 10 Week Button Used to set the temperature when the desired temperature is obtained. Used to set a day of the week. 11 Program Button 4 Operation Mode Selection Button Used to set the weekly programming. Used to select the operation mode. 12 Holiday Button l Fan Operation Mode. Used to set a holiday of the week. Cooling Operation Mode. l 13 Hour/Minute Selection Button 5 Manual Mode Selection Button Used to set the time of the day and change the time in the weekly timer Function. Used to run according to the need of selection of compressors. 14 Set Button 6 Compressor Selection Button Used to set the different program settings. Used to select one, two or three compressors. 15 Reset Button Used to set the current time and clear the setting time. 7 Filter Reset Button To reset Filter Cleaning Indicator. 9 Set the Current Time and a day of the Week 10 Weekly Programming 1 Press the Program button to start the weekly programming. The remote controller is displayed like a picture. Then ' Program set ', ' The "Program Set" will appear on LCD display. AUTO SWING OPERATION SET TEMP FAN SPEED Room Temp Operation unit 2 Press the ' Press Week Week 03 SUB FUNCTION HI MED LO AUTO Heater Preheat JET Defrost Humidify Filter Out door ZONE 1 2 3 4 Time Timer On Off Set no. Time 01 ENGLISH Program ' and '01' is blinked. Program set 05 07 09 11 13 15 17 19 21 23 ' button. Week button repeatedly until desired day appears. Week For example, if you want Thu, press 3 button 4 times. Change the time setting until the desired time is obtained. For this operation press the Set or Clear button one or more times. Set button means to switch ON. Clear button means to switch OFF. To move forward press "Min" key. To move backward press "Hour" key. SET AUTO SWING SET TEMP Room Temp CLR Operation unit On Off Set no. Time 01 Min 03 FAN SPEED SUB FUNCTION HI MED LO AUTO Heater Preheat JET Defrost Humidify Filter Out door ZONE 1 2 3 4 Time Timer Hour OPERATION Program set 05 07 09 11 13 15 17 19 21 23 * For example, if the air-conditioner is ON for 6,7,8 and 13~22 o'clock. So for the rest hours, the machine will be OFF. 4 Press the Program button again to finish weekly programmining. Program For example, the air-conditioner is on 6th,7th,8th,10th & 11th hours to remain ON and for the rest hours, turned OFF on Monday. Following steps should be followed : 1. Press Program button 2. Press Week button and select the day (Monday). 3. By pressing Min key, select 6th hour. Solid bar will blink on 6th hour. By pressing "Set" button you can set the 6th hour. Do same for the 7th, 8th, 10th and 11th hour. 4. Press Program button finally to set the above day. * To cancel the set hour press Hour button to reach upto that set hour and then press "Clear" button. * Black Bars indicate turn ON time and if there is no bar, it indicates OFF time. 11 Weekly Programming If the person has not to set the remote controller in weekly programming mode then he can cancel the weekly programming by following operations. 1 To disable the weekly programming, press the following button. Program Timer Clear If the person has to return back in weekly programming mode then he should follow the below mentioned operation. 2 To enable the weekly programming, press the following button. Program Timer Set 12 Holiday Setting If Tuesday is a holiday in this week, you may set a holiday. Press the Program button. 2 Press the Week button. Select the Tuesday. 3 Press the Holiday button. Program ENGLISH 1 Week AUTO SWING Holiday OPERATION SET TEMP FAN SPEED Room Temp AUTO Heater Preheat JET Defrost Humidify Filter Out door ZONE 1 2 3 4 Time Then the remote controller will be displayed ' The outside rectangular means holiday. '. 4 Press the Program button again to finish holiday setting. 5 To cancel the Holiday programming, press the "Holiday" button again. Timer Operation unit On Off Set no. Time 01 03 Program set 05 07 09 11 13 15 Program Timer Setting This function is used to turn on or turn off in several hours. Timer 1 Press the Timer button to turn Timer on or off. 2 Change the timer setting until the desired time is set. After you have selected the time, press "Set" button. 3 Set Hour Min If you want to cancel the timer setting, press the Timer button twice. 13 SUB FUNCTION HI MED LO Timer 17 19 21 23 Operation Mode Cooling Mode Fan Mode Cooling Mode Operation Procedure : OPERATION 1st On/Off Button SET TEMP 88 COMP1 COMP2 Room Temp FAN SPEED HIGH SUB FUNCTION Out door °C Time Timer Operation unit Sun Mon Tue Program set Wed Thu Fri Sat On Off Set no. Time 01 2nd Mode Selection Button to enter in Cooling Mode ( ) 03 05 07 09 11 13 15 17 19 21 23 3 1 3rd Room Temperature Setting Button Timer Clear Filter Program Week Holiday MANUAL 2 COMP SET In cooling mode Display shows Room Temperature, Indoor Fan Speed, Compressor Status, Cooling Mode symbol. Hour Min RESET Temperature can be set between 18°C ~ 30°C. Fan Mode In this mode only FAN runs at high speed and compressors get OFF automatically. In FAN mode Display shows - only Fan Speed & Fan Mode Symbol. 1 Press the On/Off Button. 2 Press Mode Selection Button to enter in Fan Mode ( In this mode Display will be as shown here. ). OPERATION SET TEMP 88 Room Temp FAN SPEED HIGH SUB FUNCTION °C Time Timer Operation unit Sun Mon Tue Program set Wed Thu Fri On Off Set no. Time 01 14 03 05 07 09 11 13 15 17 19 21 23 Sat Manual Operation Manual Operation is usually done according to the need of selection of compressors to run. By pressing the Manual Button display shows 2 Then press Comp Button to select the compressor from Comp1 ~ Comp2. Comp1 will start blinking OPERATION Manual SET TEMP FAN SPEED SUB FUNCTION MANUAL Comp OPERATION SET TEMP FAN SPEED SUB FUNCTION FAN SPEED SUB FUNCTION MANUAL COMP1 3 Press "Set" button to fix the COMP. On each time by pressing this button cursor will move to the next COMP. OPERATION Set SET TEMP MANUAL COMP1 COMP2 4 To cancel the Manual Operation, we have to press the Manual Button twice. Manual For eg. if we have to run Comp1 only, Press the Manual Button and press Comp Button later which showsSetCOMP1 on the screen in blinking form for which we have to press the Set Button . On each time by pressing Comp Button cursor moves to the next compressor. OPERATION MANUAL COMP1 COMP2 15 SET TEMP FAN SPEED SUB FUNCTION ENGLISH 1 Safety Device (LP - HP Operation) Used for the protection of compressors. LP and HP switch works according to gas pressure. Indication Problem OPERATION Action SET TEMP 88 Room Temp COMP2 LP1 Low gas pressure in Comp1 HP1 High gas pressure in Comp1 FAN SPEED HIGH SUB FUNCTION LP 1 Out door °C Comp1 get switch OFF Time Timer Operation unit Sun Mon Tue Program set Wed Thu Fri Sat On Off Set no. Time 01 Comp1 get switch OFF 03 05 OPERATION 07 09 11 13 SET TEMP 88 Room Temp COMP2 15 17 FAN SPEED HIGH 19 21 23 SUB FUNCTION HP 1 Out door °C Time Timer Operation unit Sun Mon Tue Program set Wed Thu Fri Sat On Off Set no. Time 01 Indication Problem LP2 Low gas pressure in Comp2 HP2 High gas pressure in Comp2 03 05 OPERATION Action 07 09 11 13 SET TEMP 88 COMP1 Room Temp 15 17 FAN SPEED HIGH 19 21 SUB FUNCTION LP 2 Out door °C Comp2 get switch OFF 23 Time Timer Operation unit Sun Mon Tue Program set Wed Thu Fri Sat On Off Set no. Time 01 Comp2 get switch OFF 03 05 OPERATION 07 09 11 13 SET TEMP 88 COMP1 Room Temp 15 17 FAN SPEED HIGH 19 21 23 SUB FUNCTION HP 2 Out door °C Time Timer Operation unit Sun Mon Tue Program set Wed Thu Fri Sat On Off Set no. Time 01 03 05 07 09 11 13 15 17 19 21 23 Filter This operation starts working after 240 hours. Display shows the Filter symbol continuously by pressing the filter button again we can reset it. OPERATION SET TEMP 88 COMP1 COMP2 FAN SPEED SUB FUNCTION Room Temp Out door Filter °C Time Timer Operation unit Sun Mon Tue Program set Wed Thu Fri Sat On Off Set no. Time 01 16 03 05 07 09 11 13 15 17 19 21 23 Child Lock Function This is the Function that any children cannot used to the air-conditioner. 1 To set the Child-Lock Function Press the Filter button then Set button. Then the operation mode shift to child lock mode and it is displayed ‘CL’ in the operation display. When you press any button in this time, the remote controller displays ‘CL’ only ON/OFF key available. 2 To cancel the Child-Lock Function Press the Filter button then Clear button. Then the child-lock mode is cancelled and the preselected mode is displayed in the remote controller. OPERATION Timer SET TEMP Operation unit FAN SPEED Sun Mon Tue Program set SUB FUNCTION Wed Thu Fri Sat On Off Set no. Time 01 03 05 07 Timer Clear Filter Program Week Holiday 09 11 13 15 17 MANUAL COMP SET Hour Min 19 RESET 17 21 23 ENGLISH Operation procedure Care and maintenance Care and maintenance Caution: Before performing any maintenance, turn off the main power to the system. Indoor Unit Never use any of the followings: q Grille, Case, and Remote Control q Turn the system off before cleaning. To clean, • Water hotter than 40°C wipe with a soft, dry cloth. Do not use bleach or Could cause deformation and/or abrasives. discoloration. Note: • Volatile substances Could damage the surfaces Supply power must be disconnected before of the air conditioner. cleaning the indoor unit. SI Be Air filters Air outlet vent 1 Air Filter n zene N NER SCO U RIN G C LB A R GER Clean the filter with a vacuum or warm, soapy water. • If very dirty, wash with a solution of detergent in lukewarm water. • If hot water (50°C or more) is used, filter may be deformed. The air filters behind Indoor unit (the suction side) should be checked and cleaned once every 2 weeks or more often if necessary. 2 After washing with water, dry well in the shade. 3 Re-install the air filter. Air outlet vent Indoor Unit Dimensions (mm) Dimension A B C D E F G H I Capacity 1625 1564 597 65 660 30 294 1220 304 1625 1564 597 65 660 30 294 1220 304 • Slope of about 5-8 mm is to be provided at the drain hole side of the indoor unit for proper drainage. • After installation the slope can be measured using a sprit level. 18 Slope 5-8 mm 102K BTU/h (LB-H0852QC) 90K BTU/h (LB-H0750QC) Outdoor Unit ENGLISH The heat exchanger coils and panel vents of the outdoor unit should be checked regularly. If clogged with dirt or soot, the heat exchanger and panel vents may be professionally steam cleaned. A Note: Dirty or clogged coils will reduce the operating efficiency of the system and cause higher operating costs. Side Rear B Air intake vents C Air outlet vents Piping Outdoor Unit MODEL A B C LB-H0852QC 600 906 1135 LB-H0750QC 600 906 1335 B C A Indoor Unit MODEL Air outlet vents A B C LB-H0852QC 460 1564 660 LB-H0750QC 460 1564 660 Air intake vents Remote Controller 19 Air filter When the air conditioner is not going to be used for a long time. When the air conditioner is to be used again. When it is not going to be used for a long time. 1 Operate the air conditioner on Air circulation mode for 2 to 3 hours. Check that the air inlet and outlet of the indoor/outdoor unit are not blocked. • This will dry out the internal parts. 2 Turn off the circuit breaker. Helpful information CAUTION CAUTION The air filters and your electiric bill. If the air filters become clogged with dust, the cooling capacity will drop, and 6% of the electricity used to operate the air conditioner will be wasted. Turn off the circuit breaker when the air conditioner is not going to be used for a long time. Dirt may collect and may cause a fire. Operation Tips Do not overcool the room. This is not good for the health and wastes electricity. Clean the air filter regularly. Blockages in the air filter reduce the airflow and lower cooling and dehumidifying effects. Clean at least once every two weeks. Keep blinds or curtains closed. Make sure that the doors and windows are shut tight. Do not let direct sunshine enter the room when the air conditioner is in operation. Avoid opening doors and windows as much as possible to keep the cool air in the room. Ventilate the room occasionally. Since windows are kept closed, it is a good idea to open them and ventilate the room now and then. 20 Troubleshooting Tips Before you call for service... Check the following points before requesting repairs or service.... If the malfunction persist, please contact your dealer. Case Explanation See page The air conditioner does not operate. • Have you made a mistake in timer operation? • On first starting, the indoor unit operates in fifteen seconds. • Has the fuse blown or has the circuit breaker been tripped? • Check that this is not a damp smell exuded by the walls, carpet, furniture or cloth items in the room. • Condensation occurs when the airflow from the air conditioner cools the warm room air. • This is the protector of the mechanism. • Wait about three minutes and operation will begin. • Is the air filter dirty? See air filter cleaning instructions. • The room may have been very hot when the room air conditioner was first turned on. Allow time for it to cool down. • Has the setting temperature been set incorrectly? • Are the indoor unit's air inlet or outlet vents obstructed? • For a noise that sounds like water flowing. -This is the sound of freon flowing inside the air conditioner unit. • For a noise that sounds like the compressed air releasing into atmosphere. -This is the sound of the dehumidifying water being processed inside the air conditioning unit. • This sound is generated by the expansion/contraction of the inlet grille, etc. due to changes of temperature. • Has the circuit breaker been tripped? 8 The room has a peculiar odor. It seems that condensate is leaking from the air Conditioner. Air conditioner does not operate for about 3 minutes when restart. Does not cool effectively. The air conditioner operation is noisy. Crack sound is heard. Remote control display is faint, or no display at all. - 11 9 - - - NOTE WATER RESISTANT The outdoor side of this appliance is WATER RESISTANT. The indoor side is not water resistant and should not be exposed to excess water. 21 ENGLISH Troubleshooting Tips! Save time and money! P/No.: 3828A33017C After reading this manual, keep it in a place easily accessible to the user for future reference.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project