LG | LBN80851QC.APUNE | LG LBN80851QC.APUNE Owner’s Manual

OWNER'S MANUAL
IMPORTANT
Please read through this manual. It contains valuable
information about your air conditioner. This manual may
help save time and money by explaining proper product
maintenance and preventing improper use.
PRECAUTIONS
Pay close attention to precautions in order to prevent
potential hazards and damage from misuse or improper
installation. LG is not responsible for any damages caused
by misuse of the product.
LG Electronics India Pvt. Ltd.
Regd. Office : A-27, Mohan Cooperative Industrial
Estate, Mathura Road, New Delhi-110044.
www.lg.com
MFL37347405
ENGLISH
LG
Ceiling Duct-Type Air Conditioner LG
Ceiling Duct-Type Air Conditioner Owner’s Manual
TABLE OF CONTENTS
F or Your Records
Write the model and serial numbers here:
Model #
Serial #
1. Safety Precautions
You can find them on a label on the side of each unit.
2. Operating Instructions
Dealer's Name
3. Care and Maintenance
Date Purchased
4. Before you call for service
R ead This Manual
Inside you will find many helpful hints on how to use
and maintain your air conditioner properly. Just a little
preventive care on your part can save you a great
deal of time and money over the life of your air
conditioner.
You'll find many answers to common problems in the
chart of troubleshooting tips. If you review our chart of
Troubleshooting Tips first, you may not need to call
for service at all.
CAUTION
• Contact the authorized service technician for repair
or maintenance of this unit.
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young
children or invalids without supervision.
• Young children should be supervised to ensure that
they do not play with the air conditioner.
• When the power cord is to be replaced, replacement
work shall be performed by authorized personnel
only.
• Installation work must be performed in accordance
with the national wiring standards by authorized
personnel only.
2
Safety
Precautions
Precautions
Incorrect operation due to ignoring instructions will cause harm or damage, the seriousness of which is
indicated by the following symbols.
WARNING
This symbol shows the possibility of death or serious injury.
CAUTION
This symbol indicates the possibility of injury or damage to property.
Never Do This
Always Do This
Installation precautions
WARNING
WARNING
n Do not install, remove and reinstall the unit by yourself.
• Improper installation will cause water leakage, electrical shock, or fire. Please consult
authorized dealer or specialist for the installation work. Please note fault caused by improper
installation is not covered by warranty.
• Unit must be installed in an easily accessible area. Any additional cost required to hire a
special equipment to service the unit will be the responsibility of the customer.
3
ENGLISH
To prevent injury and property damage, follow these instructions.
4
ENGLISH
5
6
ENGLISH
7
8
Operating
Instructions
Operating Instructions
ENGLISH
Name and Function of Remote Controller
•
(optional)
(For number of COMP selection)
*
•
(optional)
•
(optional)
• Optional feature.
9
Information of Slide Switch
1
1
2
2
3
4
3
(optional)
4
(optional)
IDU Fan Speed Provision
Capacity
IDU Fan Speed
36K BTU/h
3 Speed (Hi, Low and Medium)
51K BTU/h
3 Speed (Hi, Low and Medium)
66K BTU/h
3 Speed (Hi, Low and Medium)
90K BTU/h
3 Speed (Hi, Low and Medium)
102K BTU/h
3 Speed (Hi, Low and Medium)
132K BTU/h
3 Speed (Hi, Low and Medium)
198K BTU/h
1 Speed (Hi)
264K BTU/h
1 Speed (Hi)
When changing the product selection switch and group control switch, you must press the reset switch to use
the changed selection.
For 198K BTU/H & 264K BTU/H keep room temperature sensing on Remo.
10
Set the Current Time and a day of the Week
1
Press the '
' button.
Hour
AUTO SWING
OPERATION
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
Operation unit
2
Press the '
03
SUB FUNCTION
HI
MED
LO
Hour
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
' button.
Min
Each time the button is pressed, the number is increased from 00 to 59.
You can set the number of the current minute.
AUTO SWING
OPERATION
SET TEMP
Room Temp
Min
Operation unit
3
Press '
Week
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
' button.
Each time the button is pressed, a day of the week is shifted from sunday to saturday.
You can set the day of the week.
Week
AUTO SWING
OPERATION
SET TEMP
Room Temp
Operation unit
4
Press the '
RESET
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
' button.
If you want to reset the current time and a day of the week, click the Reset button.
AUTO SWING
OPERATION
SET TEMP
Room Temp
RESET
Operation unit
11
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
ENGLISH
Each time the button is pressed, the number is changed from 00 to 23.
You can set the number of the current hour.
Weekly Programming
1
Press the Program button.
The remote controller is displayed like a picture. Then '
Program
Program set
AUTO SWING
', '
OPERATION
' and '01' is blinked.
SET TEMP
Room Temp
2
Week
Press the '
Press
Week
03
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
07
09
' button.
button repeatedly until desired mode appears.
Week
Week
For example, if you want Thu, press
3
button 4 times.
Select the time you want.
Press
Hour
or
If you press
Min
button, then blinking letter is shown.
SET/CLR
button, then '
' shape appears.
unit
'
05
' shape means that five o'clock is reserved.
Using below buttons, you can reserve time.
SET/CLR
Hour
Min
* For example, the air-conditioner is on 6,7,8 and 13~22 o'clock.
AUTO SWING
OPERATION
SET TEMP
Room Temp
Operation unit
4
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
Press the Program button again to finish weekly programmining.
Program
12
SUB FUNCTION
HI
MED
LO
Time
Operation unit
Timer
On Off
Set no. Time 01
FAN SPEED
11
13
15
17
19
21
23
Holiday Setting
If Tuesday is a holiday in this week, you may set a holiday.
Press the Program button.
2
Press the Week button.
Select the Tuesday.
3
Press the Holiday button.
ENGLISH
Program
1
Week
AUTO SWING
Holiday
OPERATION
SET TEMP
Room Temp
4
'.
Press the Program button again to finish holiday setting.
Timer
Operation unit
On Off
Set no. Time 01
03
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
07
09
Program
Timer Setting (Delay start/Pre-set stop)
This function is used to turn on or turn off in several hours.
Timer
1
Press the Timer button
2
Change the timer setting until the desired time is set.
to turn Timer on or off.
Hour
3
If you want to cancel the timer setting, press the Cancel button.
Note :- • ON Timer is available when unit is OFF.
• OFF Timer is available when unit is ON.
• It starts counting time after Timer was set.
• Timer can be set upto 24 hours.
13
SUB FUNCTION
HI
MED
LO
Time
Then the remote controller will be displayed '
The outside rectangular means holiday.
FAN SPEED
Min
Cancel
11
13
15
17
19
21
23
Operation Mode
Cooling Mode
Soft Dry Mode
Auto Mode
Operation Procedure
1st
On/Off Button
AUTO SWING
OPERATION
SET TEMP
Room Temp
FAN SPEED
HI
MED
LO
Filter Out door
1 2 3 4
Time
Timer
Operation unit
On Off
Set no. Time 01
2nd
03
SUB FUNCTION
Program set
05
07
09
11
13
15
17
19
21
23
3
Operation Mode Selection Button
1
3rd
Room Temperature Setting Button
4th
Indoor Fan Speed Selection Button
2
4
14
Cooling Operation Mode
Press the On/Off Button.
2
Select Cooling Operation.
Press the Operation Mode Selection Button.
Each time the button is pressed, the operation mode is shifted in the arrow direction.
ENGLISH
1
COOLING MODEL
Operation Display
AUTO SWING
OPERATION
SET TEMP
FAN SPEED
Room Temp
Operation unit
Timer
On Off
Set no. Time 01
03
SUB FUNCTION
AUTO SWING
07
09
11
Timer
13
15
17
19
21
Set the temperature
lower than the room
temperature.
Operation unit
On Off
Set no. Time 01
23
03
SUB FUNCTION
07
09
OPERATION
SET TEMP
13
15
17
19
21
Operation unit
On Off
Set no. Time 01
23
03
FAN SPEED
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
Program set
05
07
09
11
13
15
17
19
21
23
Auto Operation
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Operation unit
On Off
Set no. Time 01
SET TEMP
Room Temp
Timer
11
FAN SPEED
Room Temp
OPERATION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
Program set
05
AUTO SWING
HI
MED
LO
Soft Dry Operation
AUTO SWING
Timer
FAN SPEED
Room Temp
Cooling Operation
3
SET TEMP
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
Program set
05
OPERATION
HI
MED
LO
• The temperature can be set
within a range of 18°C ~ 30°C
by 1°C .
Program set
05
07
09
11
13
15
17
19
21
23
To raise the Temperature.
To lower the Temperature.
4
Set the fan speed.
Operation Display
AUTO SWING
OPERATION
SET TEMP
Room Temp
Timer
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
07
09
11
OPERATION
Timer
13
15
17
19
21
23
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
Program set
05
AUTO SWING
HI
MED
LO
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
Program set
05
07
09
11
AUTO SWING
OPERATION
Timer
13
15
17
19
21
23
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
• Select the fan speed in three steps- high, low, medium.
• The display shows high fan speed.
• Each time the button is pressed, the fan speed mode is shifted.
15
SUB FUNCTION
HI
MED
LO
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
Program set
05
07
09
11
13
15
17
19
21
23
Soft Dry Operation Mode
This mode dehumidifies without overcooling.
1
2
Press the On/Off Button.
Select Soft Dry Operation.
Press the operation Mode Selection Button.
Each time the button is pressed, the operation mode is shifted in the arrow direction.
COOLING MODEL
Operation Display
AUTO SWING
OPERATION
SET TEMP
Room Temp
Timer
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
07
09
11
15
17
19
21
23
SET TEMP
Room Temp
Timer
13
Cooling Operation
3
OPERATION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
Program set
05
AUTO SWING
HI
MED
LO
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
07
09
11
OPERATION
Timer
13
15
17
19
21
Soft Dry Operation
23
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
Program set
05
AUTO SWING
HI
MED
LO
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
Program set
05
07
09
11
13
15
17
19
21
23
Auto Operation
During Soft Dry Operation.
• The indoor fan speed is automatically set to the low, so the shift of the indoor fan speed is
impossible because it's already being set to the best speed for Dry Operation by Micom
Control.
16
Auto Operation Mode
Press the On/Off Button.
2
To select Auto Operation , press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is shifted in the direction of the arrow.
ENGLISH
1
COOLING MODEL
Operation Display
AUTO SWING
OPERATION
SET TEMP
Room Temp
Timer
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
Program set
05
07
09
11
AUTO SWING
OPERATION
Timer
13
15
17
19
Cooling Operation
21
23
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
HI
MED
LO
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
Program set
05
07
09
11
AUTO SWING
OPERATION
Timer
13
15
17
19
21
Soft Dry Operation
23
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
HI
MED
LO
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
HI
MED
LO
Program set
05
07
09
11
13
15
17
19
21
23
Auto Operation
During Auto Operation:
q You can switch the indoor fan speed.
q The system will automatically switch from the cooling mode to the heating mode as the room temperature
and set temperature.(Heat pump model only)
17
FAN Operation
1
Press the On/Off Button.
2
Press FAN Operation Button.
3
Each time Indoor Fan Speed button is pressed, the fan speed mode is shifted in the
arrow direction.
AUTO SWING
OPERATION
SET TEMP
Room Temp
Timer
Operation unit
03
AUTO SWING
OPERATION
05
07
Operation unit
09
11
13
SET TEMP
03
AUTO SWING
OPERATION
17
19
FAN SPEED
21
23
• Fan speed is low.
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
05
07
09
11
13
SET TEMP
Room Temp
Operation unit
03
15
Program set
On Off
Set no. Time 01
Timer
• Fan speed is high.
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
Room Temp
On Off
Set no. Time 01
SUB FUNCTION
HI
MED
LO
Program set
On Off
Set no. Time 01
Timer
FAN SPEED
15
17
19
FAN SPEED
21
23
• Fan speed is medium.
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
TimeZONE
1 2 3 4
Program set
05
07
09
11
13
15
17
19
21
23
* You can't set the temperature in Fan Operation mode. To exit this mode, press 'Operation Mode' button.
* Only high fan speed is available for 198K BTU/H & 264K BTU/H. Any other speed selection leads to
malfunctioning of the unit.
18
Child Lock Function
This is the Function that any children cannot used to the air-conditioner.
1 To set the Child-Lock Function
Press the Timer button and Minute Set button for three seconds. Then the
operation mode shift to child lock mode and it is displayed ‘CL’ in the operation
display.
When you press any button in this time, the remote controller is not converted to
any selected mode and the ‘CL’ is displayed in the remote controller for about
three seconds. But the Room Temperature function is operated in spite of child
lock mode.
2 To cancel the Child-Lock Function
Press the Timer button and Minute Set button for three seconds. Then the
child-lock mode is cancelled and the preselected mode is displayed in the
remote controller.
OPE RA TI ON
T imer
Oper ation unit
SE T T EM P
SU B F UN CT IO N
Su n Mon
Prog ram s et
Tu e
Wed
17
19
Th u
Fr i
Sa t
On Off
Se t no. Time 01
03
05
07
09
11
19
13
15
21
23
ENGLISH
Operation procedure
NEO PLASMA Purification Operation (optional)
AUTO SWING
OPERATION
SET TEMP
Room Temp
FAN SPEED
HI
MED
LO
Operation unit
On Off
Set no. Time 01
03
the Start/Stop button.
1 Press
The unit will respond with a
beep.
Filter Out door
1 2 3 4
Time
Timer
SUB FUNCTION
Program set
05
07
09
11
13
15
17
19
21
23
the door of the remote
2 Open
controller. Press the PLASMA
button.
Operation will start when the button
is pressed and stop when the button
is pressed again.
20
Heating Operation (Heat Pump model only)
ENGLISH
1
2
3
4
Select Heat mode
AUTO SWING
OPERATION
SET TEMP
Room Temp
FAN SPEED
HI
MED
LO
Operation unit
03
Press the Start/Stop button.
The unit will respond with
a beep.
2
Open the door of the remote controller. To select Heating
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the arrow.
SUB FUNCTION
Filter Out door
1 2 3 4
Time
Timer
On Off
Set no. Time 01
1
Program set
05
07
09
11
13
15
17
19
21
23
Cooling
21
Auto
Healthy
Heating
Dehumidification (Heat pump model only)
Pressure Function
Sr.
No.
*
KEY & MODE
OPERATION
ERROR
RESET
Low Pressure
Function
(LP Operation)
– When Low Pressure operates, it
stops Comp as well as O/D Unit
after 10 sec of Comp Operation.
Respective Comp No.
will blink.
Blinking Zone 1 2 3
Manual power reset.
Respective Comp No.
will blink.
Blinking Zone 1 2 3
Manual power reset.
– If Comp Off occurs 3 times in 1
hour by L/P operation after the
first detection, Comp Off state has
been maintained.
*
High Pressure
Function
(HP Operation)
– When High Pressure operates, it
stops Comp as well as O/D Unit
after 10 sec of Comp Operation.
– If Comp Off occurs 3 times in 1
hour by H/P operation after the
first detection, Comp Off state has
been maintained.
*
Power Failure
Compensation
(Memory Function)
– Micom remembers the previous
running condition before power
failure, such as On/Off condition,
running mode, set temperature,
weekly programming etc.
Error Diagnosis
Sr.
No.
ERROR CODE
DIAGNOSIS
DESCRIPTION
1
CH-01
Check room thermistor
Recover after 5 seconds of operation when respective
thermistor healthy
2
CH-02
Check pipe thermistor (CN-Pipe/In)
Recover after 3 seconds of operation when respective
thermistor healthy
3
CH-06
Check pipe thermistor (CN-Pipe/Out)
Recover after 3 seconds of operation when respective
thermistor healthy
4
CH-12
Check pipe thermistor (CN-Pipe/Med)
Recover after 4 seconds of operation when respective
thermistor healthy
5
CH-09
Check Option PCB (EPROM)
Check Interconnection of Option PCB and Power Reset
6
CH-04
Check float sensor / Jumper
Recover after 4 minutes of operation when float sensor /
Jumper healthy
7
CH-14
Check Sub PCB
Check Interconnection of Sub PCB / Recover after
5 seconds of Healthy Interconnection
22
Address Setup of Central Control
ENGLISH
23
The Room Temperature Confirmation
24
Operation Details
• Cooling Operation Mode
ROOM TEMP.
More 3 minutes
OPERATION START
SET TEMP. +0.5°C)
OPERATION STOP
SET TEMP. -0.5°C)
INDOOR FAN
OUTDOOR FAN/COMP
: SETTING FAN SPEED
: LOW COOL OPERATION
: COMP ON
: COMP OFF
Helpful information
Airflow speed and cooling capacity.
The cooling capacity indicated in the specification is
the value when the fan speed is set to high, and the
capacity will be lower at low or medium fan speed.
High fan speed is recommended when you wish to
cool the room quickly.
h
Hig ed
e
p
S
Self-Diagnosis Function
Remote Controller display will flash Error Code when a problem occurs, please contact your Dealer.
(for e.g., CH-01)
25
ENGLISH
When the room temperature is higher than the set temperature, it operates in cooling mode at the set
temperature, the set fan speed, and then it will be in automatically turn off when the room temperature
reaches the set temperature +0.5¡C.
Care and
maintenance
Care and maintenance
Caution: Before performing any maintenance, turn off the main power to the system.
Indoor Unit
Grille, Case, and Remote Control:
q Turn the system off before cleaning. To clean,
wipe with a soft, dry cloth. Do not use bleach or
abrasives.
Note:
Supply power must be disconnected before
cleaning the indoor unit.
q Never use any of the followings:
• Water hotter than 40°C
Could cause deformation and/or
discoloration.
• Volatile substances
Could damage the surfaces
of the air conditioner.
SI
Be
n zene
N NER
SCO
U RIN G
C LB
A R GER
Air filters
Air outlet vent
q Cleaning Tips:
Air Filter:
The air filters behind Indoor unit
(the suction side) should be checked and cleaned
once every 2 weeks or more often if necessary.
1
Clean the filter with a vacuum or warm, soapy
water.
• If very dirty, wash with a solution of
detergent in lukewarm water.
• If hot water (50°C or more) is used, filter
may be deformed.
2
After washing with water, dry well in the shade.
3
Re-install the air filter.
Air outlet vent
Indoor Unit Dimensions (mm)
Dimension
36K BTU/H
Model
A
B
C
D
E
F
G
H
I
LB-G0307QC 1240 1180 365 57.5 480 30 290 850 205
51K BTU/H
LB-E0423QC 1291 1230 565 57.5 680 30 294 1025 312
51K BTU/H
LB-R0420QC 1291 1230 380 57.5 590 30 130 1005 232
66K BTU/H
LB-E0552QC 1291 1230 485 57.5 600 30 294 1025 312
LB-R0550QC/
1291 1230 380 57.5 590 30 130 1005 232
LB-R0551QC
66K BTU/H
90K BTU/H
LB-H0752QC 1625 1564 510 65
660 30 294 1220 304
* 90K BTU/H
LB-R0750QC 1625 1562 510 65
688 30 294 1220 304
102K BTU/H
*102K BTU/H
132K BTU/H
LB-H0853QC
LB-80850QC
LB-80851QC
LB-J1105QC
LB-81100QC
1625 1564 510 65
660 30 294 1220 304
1625 1562 510 65
688 30 294 1220 304
1765 1705 597 55
692 30 294 1220 304
1625 1562 510 65
688 30 294 1220 304
198K BTU/H
LB-K1653QC 1987 1930 755 55
865 30 294 1260 422
264K BTU/H
LB-M2200QC 2110 2050 920 55 1080 22 294 1488 494
*132K BTU/H
* is applicable for single piping model only.
• Slope of about 5-8 mm is to be provided at the
drain hole side of the indoor unit for proper
drainage.
• After installation the slope can be measured
using a sprit level.
26
Slope 5-8 mm
Capacity
Outdoor Unit
The heat exchanger coils and panel vents of the outdoor unit should be checked regularly. If clogged
with dirt or soot, the heat exchanger and panel vents may be professionally steam cleaned.
ENGLISH
Note:
Dirty or clogged coils will reduce the operating efficiency of the system and cause higher operating costs.
Outdoor Unit
D
W
D
Air intake
vents
H
H
W
(Rear)
(Side)
Control Cover
Connecting Wire
Air outlet
vents
Indoor Unit
Connection Pipe
Drain Hose
AIR FILTER
AIR INTAKE VENTS
W
D
CONTROL
BOX
H
AIR
OU
REMOTE
CONTROLLER
TL
ET
VE
NT
S
(For 198K & 264K Units)
Dimension
Capacity
36K BTU/H
51K BTU/H
51K BTU/H
66K BTU/H
66K BTU/H
66K BTU/H
90K BTU/H
* 90K BTU/H
102K BTU/H
* 102K BTU/H
* 102K BTU/H
132K BTU/H
132K BTU/H
132K BTU/H
* 132K BTU/H
198K BTU/H
264K BTU/H
Model
LB-G0307QC
LB-E0423QC
LB-R0420QC
LB-E0552QC
LB-R0550QC
LB-R0551QC
LB-H0752QC
LB-80750QC
LB-H0853QC
LB-80850QC
LB-80851QC
LB-J1104QC
LB-J1103QC
LB-J1105QC
LB-81100QC
LB-K1653QC
LB-M2200QC
Indoor Unit (mm)
IDU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
W
1180
1230
1230
1230
1230
1230
1564
1562
1564
1562
1562
1700
1700
1700
1562
1985
2050
* is applicable for single piping model only.
27
Outdoor Unit (mm)
D
H
ODU
W
D
H
480
600
590
600
590
590
660
688
660
688
688
690
690
690
688
865
1080
295
370
380
370
380
380
460
460
460
460
460
460
460
460
460
595
640
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
3
2
870
906
906
906
906
899
906
906
906
906
995
970
906
970
995
906
970
320
406
406
406
406
355
600
600
600
600
475
570
406
670
475
406
570
655
1135
1135
1135
1135
1135
1135
1135
1135
1135
1360
1310
1135
1310
1360
1135
1310
When the air conditioner is not going to be used for a long time.
When the air conditioner is to
be used again.
When it is not going to be used for
a long time.
1
n Check that the air inlet and outlet of the
indoor/outdoor unit are not blocked.
Operate the air conditioner on Air circulation
mode (Refer to page 15) for 2 to 3 hours.
• This will dry out the internal parts.
2
Turn off the circuit breaker.
Helpful information
CAUTION
CAUTION
The air filters and your electiric bill.
If the air filters become clogged with dust, the
cooling capacity will drop, and 6% of the
electricity used to operate the air conditioner will
be wasted.
Turn off the circuit breaker when the air conditioner
is not going to be used for a long time.
Dirt may collect and may cause a fire.
Operation Tips
Do not overcool the room.
This is not good for the health
and wastes electricity.
Clean the air filter regularly.
Blockages in the air filter
reduce the airflow and lower
cooling and dehumidifying
effects. Clean at least once
every two weeks.
Keep blinds or curtains
closed.
Make sure that the doors
and windows are shut tight.
Do not let direct sunshine
enter the room when the air
conditioner is in operation.
Avoid opening doors and
windows as much as possible
to keep the cool air in the
room.
Ventilate the room
occasionally.
Since windows are kept
closed, it is a good idea to
open them and ventilate the
room now and then.
28
Troubleshooting
Tips
Before you call for service...
Check the following points before requesting repairs or service.... If the malfunction persist, please contact your
dealer.
Case
The air conditioner does not
operate.
The room has a peculiar odor.
It seems that condensate is
leaking from the air Conditioner.
Air conditioner does not operate
for about 3 minutes when restart.
Does not cool or heat effectively.
The air conditioner operation is
noisy.
Crack sound is heard.
Remote control display is faint, or
no display at all.
Explanation
See page
Have you made a mistake in timer operation?
On first starting, the indoor unit operates in
fifteen seconds.
l Has the fuse blown or has the circuit breaker
been tripped?
l Check power supply for single/reverse phase,
voltage imbalance.
l Check that this is not a damp smell exuded by
the walls, carpet, furniture or cloth items in the
room.
l Condensation occurs when the airflow from the
air conditioner cools the warm room air.
l This is the protector of the mechanism.
l Wait about three minutes and operation will
begin.
l Is the air filter dirty? See air filter cleaning
instructions.
l The room may have been very hot when the
room air conditioner was first turned on. Allow
time for it to cool down.
l Has the setting temperature been set
incorrectly?
l Are the indoor unit's air inlet or outlet vents
obstructed?
l For a noise that sounds like water flowing.
-This is the sound of freon flowing inside the air
conditioner unit.
l For a noise that sounds like the compressed air
releasing into atmosphere.
-This is the sound of the dehumidifying water
being processed inside the air conditioning
unit.
l This sound is generated by the
expansion/contraction of the inlet grille, etc. due
to changes of temperature.
l Has the circuit breaker been tripped?
8
l
l
-
-
16
10
-
-
-
NOTE
WATER RESISTANT: The outdoor side of this appliance is WATER RESISTANT.
The indoor side is not water resistant and should not be exposed to excess
water.
29
ENGLISH
Troubleshooting Tips! Save time and money!
8. Group Control
SET TEMP
Time
Operation unit
03
05
07
Terminal(Local Supply)
Block
Connector
Terminal(Local Supply)
Block
Connector
Indoor Unit 2
Indoor Unit 1
RED(12V)
YL(SIGNAL)
BR(GND)
FAN SPEED SUB FUNCTION
HI
MED
LO
ZONE
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
1 2 3 4
Main PCB
#1
YL(SIGNAL)
BR(GND)
YL(SIGNAL)
BR(GND)
Main PCB
#2
....
11
13
15
17
19
21
YL(SIGNAL)
BR(GND)
Indoor Unit 16
Terminal(Local Supply)
Block
Connector
YL(SIGNAL)
BR(GND)
Main PCB
#16
• Using the supplied Wired Remote Controller,
wire them like above.
OP7
Remote
Controller
PCB
Program set
09
ENGLISH
It operates maximum 16 Units by only one Wired Remote Controller,
and each Unit starts sequentially to prevent overcurrent.
Main PCB
RED(12V)
YL(SIGNAL)
BR(GND)
Connecting Cable(Local Supply)
....
Slide Switch
AUTO SWING OPERATION
Room Temp
Timer
On Off
Set no. Time 01
23
Wired Remote Controller
(Standard)
• Remove the OP7 resistor.
(Use soldering Iron or others)
• Ensure that the color of wire.
9. Two Thermistor system
• Open the rear cover of Remote
Controller to set up the mode.
Room Temp. Sensing
Remo.
Indoor Unit
2 TH(Remo.+Indoor)
Slide Switch
• Selectable options are three as follows.
- Remo: Sensing the room Temperature.
- Indoor Unit: Sensing the intake air into
indoor Unit.
- 2 TH: Sensing the lower temperature of
the two thermistors.
CAUTION
• On installing, don't impact to the PCB
and LCD display.
• Don't remove the protection sheet.
• Use the specified screw.
• On installing, turn off the main power.
• To set up the mode, adjust the slide
switch to desired mode position on
installing.
After reading this manual, keep it in a place easily accessible to the user for future reference.
31
7. Air Purging of the Connecting Pipes and the Indoor Unit
The air which contains moisture remaining in the refrigeration cycle may cause a malfunction
on the compressor.
1. Confirm that both the liquid side valve and the gas side valve are set to the closed position.
2. After connecting the piping, check the joints for gas leakage with gas leak detector.
3. Remove the service port nut, and connect the gauge manifold and the vacuum pump to the
service port by the charge hose.
4. Vacuum the indoor unit and the connecting pipes until the pressure in them lowers to below 76cmHg.
5. Remove the valve stem nuts, and fully open the stems of the 2-way and 3-way valves with a
hexagon wrench.
6. Tighten the valve stem nuts of the 2-way valve and 3-way valve.
7. Disconnect the charge hose and fit the nut to the service port.
(Tightening torque: 1.8kg.m)
Indoor unit
Liquid side
Closed
2-way valve/
3-way valve
Outdoor unit
Gas side
3-way
valve
Closed
Vaccum pump
OPEN
CLOSE
30
4) Form the pipings
Seal a small opening
around the pipings
with gum type sealer.
ENGLISH
1. Wrap the connecting portion of indoor
unit with the Insulation material and
secure it with two Plastic Bands. (for the
right pipings)
• If you want to connect an additional drain
hose, the end of the drain-outlet should
keep distance from the ground. (Do not
dip it into water, and fix it on the wall to
avoid swinging in the wind.)
In case of the Outdoor unit being installed
below position of the Indoor unit.
Suction Pipe
Insulation
2. Tape the Pipings, drain hose and
Connecting Cable from bottom to top.
3. Form the pipings gathered by taping
along the exterior wall and fix it onto the
wall by saddle or equivalent.
In case of the Outdoor Unit being installed
above position of the Indoor Unit.
Seal a small opening
around the pipings
with gum type sealer.
1. Tape the Pipings and Connecting cable
from bottom to top.
Trap
2. Form the pipings gathered by taping
along the exterior wall, and make the
trap prevent water from entering into the
room.
3. Fix the pipings onto the wall by saddle
or equivalent.
29
3) Connecting the cable to the
Outdoor Unit
Outdoor unit
Terminal block
1. Remove the Cover control from the unit
by loosening a screw.
Connect the wires to the terminals on
the control board individually as
following.
2. Secure the cable onto the control board
with the holder (clamper).
Cord Clamper
Over 5mm
3. Refix the cover control to the original
position with the screw.
Cover control
Power supply
cord
CAUTION
After the confirmation of the above conditions, prepare the wiring as follows:
1) Never fail to have an individual power specialized for the air conditioner. As for the method
of wiring, be guided by the circuit diagram pasted on the inside of control box cover.
2) Provide a circuit breaker switch between power source and the unit.
3) The screw which fasten the wiring in the casing of electrical fittings are liable to come
loose from vibrations to which the unit is subjected during the course of transportation.
Check them and make sure that they are all tightly fastened. (If they are loose, it could give
rise to burn-out of the wires.)
4) Specification of power source
5) Confirm that electrical capacity is sufficient.
6) Be sure that the starting voltage is maintained at more than 90 percent of the rated voltage
marked on the name plate.
7) Confirm that the cable thickness is as specified in the power sources specification.
(Particularly note the relation between cable length and thickness.)
8) Never fail to equip a leakage breaker where it is wet or moist.
9) The following troubles would be caused by voltage drop-down.
• Vibration of a magnetic switch, damage on the contact point there of, fuse breaking,
disturbance to the normal function of a overload protection device.
• Proper starting power is not given to the compressor.
10) Appliance mst be grounded.
• To minimize the risk of electric shock, you must always plug into a grounded outlet.
• Do not cut or remove the grounding.
28
6. Connecting Cables between Indoor and Outdoor Unit
ENGLISH
1) Connecting cables to the Indoor Unit
Connect the wires to the terminals on the control board individually according to the
outdoor unit connection.
• Ensure that the color of the wires of outdoor unit and the terminal No. are the same as
those of indoor unit respectively.
Please do the interconnection as per Interconnection Table in wiring diagram.
CAUTION
The power cord connected to the outdoor unit should be
with the following specifications
The connecting cable connected to the indoor and outdoor
unit should be with the following specifications
NORMAL CROSS-SECTIONAL AREA
GN
/YL
Capacity
36K BTU/h
60K BTU/h
3 Phase
2.5mm
3.5mm
GN
/Y
L
20
NORMAL
CROSS-SECTIONAL
AREA
1.25mm2 (36K/60K)
20
mm
mm
If the supply cord is damaged, it must be replaced by a special cord or assembly availible from the manufacturer of its service agent.
WARNING
Make sure that the screws of the terminal are free from looseness.
2) Clamping of cables
1) Arrange 2 power cables on the control panel.
2) First, fasten the steel clamp with a screw to the inner boss of control panel.
3) For the cooling model, fix the other side of the clamp with a screw strongly.
27
Wiring Diagram
Unit : 264K BTU/H
CONTROL BOX WIRING DIAGRAM
In door & control box connection detail
CONTROL BOX
Terminal No.
N
L3 L2 L1
3ø MONITORING
RELAY
18 15
R Y B N
R Y B N
DRY
CONTACT
WIRED REMOTE
CONTROLLER
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
IDM PHASE (R)
IDM PHASE (Y)
IDM PHASE (B)
IDM PHASE T.O.P.
IDM PHASE T.O.P.
1
2
3
4
5
6
7
INDOOR
3Ø415 V
POWER SUPPLY
1
2
3
4
5
TP
TP
IDM PHASE (R)
IDM PHASE (Y)
IDM PHASE (B)
IDM PHASE T.O.P.
IDM PHASE T.O.P.
R Y BN
Out Door & Control Box Connection Detail
COMP1
IDM
CN-CC
COMP2
CN-PIPE
CN-ROOM
CN-REMO
CN-PTC
CONTROL BOX
N
27 N
BK
RD
CN-POWER
CN-TAB CN-MOTOR1
FUSE 250V RY-D/PUMP
10A CN-D/PUMP
LOW MED HI
NE
-ZO
CN
CN-OUT
COMP3 COMP2 COMP1
OUTDOOR
Terminal No.
MAIN PCB ASSEMBLY
26 L
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
28 HI
29 C3
30 C2
31 C1
TERMINAL
T
OA
-FL
CN
CN-OPTION
1
2
3
4
22
21
20
COMP B PHASE (B)
COMP B PHASE (Y)
COMP B PHASE (R)
COMP 2 PHASE (B)
COMP 2 PHASE (Y)
COMP 2 PHASE (R)
B
Y
R
8
9
ODM1 PHASE
ODM1 NEUTRAL
3Ø415 V
POWER SUPPLY
B
Y
R
19
18
17
COMP A PHASE (B)
COMP A PHASE (Y)
COMP A PHASE (R)
BL
BL
DRAIN
PUMP
OPTION PCB
ASSEMBLY
WH
WH
WH
OR
BL
COMP 1 PHASE (B)
COMP 1 PHASE (Y)
COMP 1 PHASE (R)
L
N
GR
ODM1 PHASE (L)
ODM1 NEUTRAL (N)
EARTH (GR)
BODY OF CONTROL BOX
BL
CN-H/P_A
RD
BK
CN-N
RD
BK
10
11
ODM2 PHASE
ODM2 NEUTRAL
BR
CN-L
L
N
GR
BODY OF CONTROL BOX
HP2
LP2
HP1
LP1
35
34
33
32
HP2
LP2
HP1
LP1
CN-ZONE
CN-L/P_A
CN-H/P_B
ODM2 PHASE (L)
ODM2 NEUTRAL (N)
EARTH (GR)
HP2
LP2
HP1
LP1
CN-L/P_B
SUB PCB ASSEMBLY
R Y B N
1 2 3 4
5 6 7 TP TP
IDM
3ø POWER
SUPPLY
17 18 19
COMP1
20 21 22
COMP2
8 9
ODM1
10 11
ODM2
32
33
34
35
LP1 HP1 LP2 HP2
EBY33415409
OUTDOOR WIRING DIAGRAM
OUT(A)
MOTOR
OUT(B)
MOTOR
COMP(1)
BK
From
ODM
From C-Box Body
4
N
5
P
6
G
BK
GR
BK
T1
BK
T3
T2
RD WH BK
TERMINAL (C)
TERMINAL (B)
TERMINAL (A)
Y
R
2
3
8
LP
1
B
7
HP
From
HP-LP
From COMP1
BL
RD
HP 1
BL
3854A22012C
LP 1
26
Wiring Diagram
Unit : 198K BTU/H
R
R
Y
B
Y
B
B
N
R Y BN
In door & control box connection detail
CONTROL BOX
Terminal No.
R
Y
B
N
R Y B N
N
N
DRY
CONTACT
WIRED REMOTE
CONTROLLER
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
IDM PHASE (R)
IDM PHASE (Y)
IDM PHASE (B)
IDM PHASE T.O.P.
IDM PHASE T.O.P.
1
2
3
4
5
6
7
INDOOR
3Ø415 V
POWER SUPPLY
1
2
3
4
5
TP
TP
IDM PHASE (R)
IDM PHASE (Y)
IDM PHASE (B)
IDM PHASE T.O.P.
IDM PHASE T.O.P.
ENGLISH
CONTROL BOX WIRING DIAGRAM
R
Y
L1 L2 L3
3ø MONITORING
RELAY
18 15
R Y B N
R Y BN
Out Door & Control Box Connection Detail
COMP1
IDM
COMP2
CN-CC
COMP3
CN-PIPE
CN-ROOM
CN-REMO CN-PTC
CONTROL BOX
N
BK
RD
CN-POWER
CN-TAB CN-MOTOR1
FUSE 250V RY-D/PUMP
10A CN-D/PUMP
LOW MED HI
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
NE
-ZO
CN
CN-OUT
COMP3 COMP2 COMP1
T
OA
-FL
CN
CN-OPTION
OPTION PCB
ASSEMBLY
WH WH WH
20 21 22
23 24 25
8 9
COMP3
ODM1
10 11
ODM2
12 13
ODM3
32
33
34
35
36
CN-H/P_A
RD
BK
CN-N
RD
BK
OUTDOOR
Terminal No.
MAIN PCB ASSEMBLY
26 L
27 N
28 HI
29 C3
30 C2
31 C1
TERMINAL
BL
BL
DRAIN
PUMP
17 18 19
COMP2
1
2
3
4
25
24
23
22
21
20
COMP C PHASE (B)
COMP C PHASE (Y)
COMP C PHASE (R)
COMP B PHASE (B)
COMP B PHASE (Y)
COMP B PHASE (R)
3Ø415 V
POWER SUPPLY
B
Y
R
B
Y
R
COMP 3 PHASE (B)
COMP 3 PHASE (Y)
COMP 3 PHASE (R)
COMP 2 PHASE (B)
COMP 2 PHASE (Y)
COMP 2 PHASE (R)
B
Y
R
8
9
ODM1 PHASE
ODM1 NEUTRAL
BL
CN-H/P_B
RD
BK
COMP 1 PHASE (B)
COMP 1 PHASE (Y)
COMP 1 PHASE (R)
L
N
GR
ODM1 PHASE (L)
ODM1 NEUTRAL (N)
EARTH (GR)
BODY OF CONTROL BOX
BR
CN-L
10
11
ODM2 PHASE
ODM2 NEUTRAL
CN-ZONE
CN-L/P_A
L
N
GR
BODY OF CONTROL BOX
12
13
ODM3 PHASE
ODM3 NEUTRAL
CN-L/P_B
SUB PCB ASSEMBLY
CN-H/P_C
5 6 7 TP TP
COMP1
19
18
17
COMP A PHASE (B)
COMP A PHASE (Y)
COMP A PHASE (R)
WH
YL
OR
BL
R Y B N
1 2 3 4
IDM
3ø POWER
SUPPLY
L
N
GR
ODM2 PHASE (L)
ODM2 NEUTRAL (N)
EARTH (GR)
ODM3 PHASE (L)
ODM3 NEUTRAL (N)
EARTH (GR)
BODY OF CONTROL BOX
CN-L/P_C
37
HP3
LP3
HP2
LP2
HP1
LP1
37
36
35
34
33
32
HP3
LP3
HP2
LP2
HP1
LP1
LP1 HP1 LP2 HP2 LP3 HP3
HP3
LP3
HP2
LP2
HP1
LP1
EBY33415410
OUTDOOR WIRING DIAGRAM
COMP
MOTOR
1
EARTH
T1
T3
BLACK
MOTOR
2
T2
RD
WH
BK
T/B1
GR
YELLOW
ORANGE
YELLOW
BLACK
7
TERMINAL B
8
R
9
B
Y
10
11
RD
12
E
ORANGE
BK
CAPACITOR 1
CAPACITOR 2
From C-Box Body
From Control Box
BK
1
2
3
4
HP
RD
RD
LP
5
6
L
BK
TERMINAL A
N
BL
From C.BOX
LP SWITCH
From C.BOX
(1ø,230V)
HP SWITCH
3854A22012B
25
Wiring Diagram
Unit : 132K BTU/H (1 ODU - Single Piping)
In door & Out door connection detail
COMP(1)
L1
OUTDOOR WIRING DIAGRAM
L3
MOTOR
GREY R 2 C
S
MOTOR
R 1C
S
15 18
25 28
3ø MONITORING
RELAY
A2
L1 L2 L3
A1
CAPACITOR
2
9
10
LP1/HP1
LP1/HP1
CAPACITOR
1
OUTDOOR
Terminal No.
PHASE
NEUTRAL
COMP1
GND
RD
Contactor
1
2
3
4
5
6
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
GND IN
NC
1
7
PHASE
2
8
NEUTRAL
3
4
5 IN door motor
6
10
7
COMP1
8
9
GND
GREY
RD
L1 L2 L3
1 Magnetic
INDOOR
3Ø415 V
POWER SUPPLY
L2
RD
RD WH BK
Magnetic Contactor(1)
11
12
LP1/HP1
LP1/HP1
GREY
T1 T2 T3
GREY
RD YL BL BK
YL
BK
1
2
3
5
4
B
6
RD YL BL
BK
BK
GN/YL
GN/YL
TERMINAL (A)
R Y
GND
N G
7
8
9
10 11 12
TERMINAL (B)
13
P N G S HP LP
3Ø415 V
POWER SUPPLY
TERMINAL (C)
14
BLACK
BLACK
BLACK
BLACK
NORMAL CROSS-SECTIONAL AREA
WIRE NO.
TO INDOOR FROM INDOOR
1Ø230 V
LP 1
HP 1
SPECIFICATION
1.5 mm 2
7,8, & 9
10 mm 2
1,2,3,4 & 5
1.0 mm 2
10,11, &12
5 CORE
3 CORE
3 CORE
WIRED REMOTE
CONTROLLER
DRY
CONTACT
INDOOR WIRING DIAGRAM
TO OUTDOOR UNIT
BR
1(L) 2(N) 3
BL
CN-PIPE
CN-CC
BR
BL
5
6
INDOOR MOTOR
(1 & 2)
BK
WH
RD
BL
4
BK
WH
RD
BL
CN-ROOM
CN-REMO CN-PTC
MAIN PCB ASSEMBLY
NE
-ZO
CN-POWER
FUSE250V
CN
RY-D/PUMP
10A
LOW MED HI COMP3 COMP2 COMP1
CN-D/PUMP
CN-TAB
BL
BL BR
CN-MOTOR1
T
OA
-FL
CN
CN-OPTION
CN-OUT
BL
RD
DRAIN
PUMP
OPTION PCB
ASSEMBLY
BL
TO OUTDOOR HP/LP & GND INPUT
(SIGNAL) FROM OUTDOOR
UNIT
CN-N
COMP1
BR
CN-L
CN-ZONE
7
RD
8
GN/YL BODY OF THE
CONTROL BOX
9
RD
10
SUB PCB ASSEMBLY
BK
11
CN-H/P_1
CN-L/P_1
12
GREEN/YELLOW
GN/YL
RED
RD
BLACK
BK
OR
ORANGE BR
YL
YELLOW
BL
WH
GN
BLUE
BROWN
WHITE
GREEN
EBY43304431
24
Wiring Diagram
Unit :132K BTU/H (2 ODU)
BLACK
T3
C2R
S
1
CS R
MOTOR
MOTOR
YELLOW
ORANGE
T2
COMP.2
T1
BLACK
T3
C 2R
S
1
CS R
MOTOR
MOTOR
INDOOR
18 15
3ø MONITORING
RELAY
YELLOW
TB1
BLACK CAPACITOR
1
ORANGE
CAPACITOR
2
RD7
20 RD
20 RD
BK 11
T1 T2 T3
BK 8
7
L1 L2 L3 A2
MAGNETIC
CONTACTOR
BK 11
TB2
BK 9
BLACK CAPACITOR
1
ORANGE
18 15
3ø MONITORING
RELAY
34 RD
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
GND IN
NC
1
7 PHASE
2
8 NEUTRAL
6 GND
3
7
COMP1(FOR UNIT1)
3
8
COMP2(FOR UNIT2)
3
4
5 IN door motor
6
CAPACITOR
2
BK 11
BK 11
TB2
LP/HP1
LP/HP1
LP/HP2
LP/HP2
9
10
11
12
4
5
4
5
LP/HP1(FOR UNIT1)
LP/HP1(FOR UNIT1)
LP/HP2(FOR UNIT2)
LP/HP2(FOR UNIT2)
L3 L2 L1
A1
BK 9
BL 6
YL 5
RD 4
34 RD
RD 1 YL 2 BL 3 BK 8
RD
9
OUTDOOR
Terminal No.
7
8
3Ø415 V
POWER SUPPLY 9
10
11
12
YELLOW
ORANGE
T2
YELLOW
TB1
20 RD
20 RD
34 RD
PHASE
NEUTRAL
C/B BODY
COMP1
COMP2
RD WH BK
RD 7
RD
8
ENGLISH
In door & Out door connection detail
OUTDOOR WIRING DIAGRAM
COMP.1
T1
RD WH BK
L3 L2 L1
T1 T2 T3 A1
A2
L1 L2 L3
MAGNETIC
CONTACTOR
BL 6
YL 5
RD 4
34
RD 1 YL 2 BL 3 BK 8
RD
BK 8
7
GN GN
7
35 RD
GN GN
1
10 11 12
2
3
4
5
6
TERMINAL B
TERMINAL A
L N
RD YL BL BK GN
7
35 RD
G
HP1
LP1
SWITCH SWITCH
8
9
1
10 11 12
2
3
4
5
6
TERMINAL B
TERMINAL A
G
RD YL BL BK GN
FROM
FROM
TO
INDOOR INDOOR INDOOR
(SIGNAL) (HP/LP)
HP2
LP2
SWITCH SWITCH
FROM FROM TO
INDOOR INDOOR INDOOR
(SIGNAL) (HP/LP)
NORMAL CROSS-SECTIONAL AREA
WIRE NO.
3ø 415V
POWER SUPPLY
SPECIFICATION
1.0 mm 2
3,4 & 5
1.5 mm 2
1,2 & 6
10 mm 2
7,8,9,10 & 11
5 CORE
3 CORE
3 CORE
BODY OF THE CONTROL BOX
BR
1(L) 2(N) 3
TO OUTDOOR UNIT
GN/YL
WIRED REMOTE
CONTROLLER
DRY
CONTACT
INDOOR WIRING DIAGRAM
BL
CN-PIPE
CN-CC
BR
CN-ROOM
CN-REMO CN-PTC
BL
5
6
INDOOR MOTOR
(1 & 2)
MAIN PCB ASSEMBLY
4
BK
WH
RD
BL
NE
-ZO
CN-POWER
LOW MED HI COMP3 COMP2 COMP1
CN-D/PUMP
CN-MOTOR1
CN-TAB
BL
T
OA
-FL
CN
RY-D/PUMP
FUSE250V
10A
BL BR
CN
CN-OPTION
CN-OUT
BL
DRAIN
PUMP
RD
BL
OPTION PCB
ASSEMBLY
BL
CN-N
BR
CN-L
10
9
BL
RD
8
TO OUTDOOR
(SIGNAL)
CN-ZONE
RD
7
COMP1
COMP2
BK
11
FROM OUTDOOR
UNIT
SUB PCB ASSEMBLY
RD
CN-H/P_1
CN-L/P_1
12
BK
CN-H/P_2
CN-L/P_2
GREEN/YELLOW
GN/YL
RED
RD
BLACK
BK
OR
YL
BL
ORANGE BR
YELLOW
BROWN
WH
GN
BLUE
WHITE
GREEN
EBY43304424
23
Wiring Diagram
Unit : 132K BTU/H
OUTDOOR WIRING DIAGRAM
COMP(1)
COMP(2)
In door & Out door connection detail
W
OUT(A)
MOTOR
BK
U
TERMINAL (C)
21 21
BL BL
28 25
RD
18 15 20
W
V
U
V
OUT(B)
MOTOR
BK
BK BK
14 13
INDOOR
BK WH RD
BK WH RD
L3 L2 L1
RD 7
L1 L2 L3
A2
A1
Magnetic A
Contactor
BK T1 T2 T3
BL YL RD
L1 L2 L3
A2
A1
OUTDOOR
Terminal No.
3Ø415 V
POWER SUPPLY
BL
RD
20
3ø MONITORING
RELAY
Magnetic B
Contactor
11 11 T1 T2 T3
BK
9 8 7
BK BL YL RD
LP/HP1
LP/HP1
LP/HP2
LP/HP2
1
2
3
4
5
6
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
GND IN
NC
1
7
PHASE
2
8
NEUTRAL
9
GND
10
7
COMP1
11
8
COMP2
3
4
5 IN door motor
6
PHASE
NEUTRAL
C/B BODY
COMP1
COMP2
RD 7
BK
11
6 5 4
BL YL RD
BK
Magnetic Contactor(1)
Magnetic Contactor(2)
9
10
11
12
15
16
17
18
LP/HP1
LP/HP1
LP/HP2
LP/HP2
YL 27
To Indoor
BK
BK 28
GN/YL
3
GN/YL
20 19 18 17 16 15
38
38
TERMINAL (D)
TERMINAL (B)
12 11 10
9
5
7 GND 6
8
4
3
2
1
1 TERMINAL (A)
2
30
30
G N
G
B
Y R
NORMAL CROSS-SECTIONAL AREA
WIRE NO.
HP 2
LP 2
HP 1
3Ø415 V
POWER SUPPLY
FROM INDOOR TO INDOOR
1Ø230 V
LP 1
INDOOR WIRING DIAGRAM
SPECIFICATION
1.0 mm 2
15,16,17&18
1.5 mm 2
7,8,9,10 & 11
10 mm 2
1,2,3,4 & 5
5 CORE
5 CORE
4 CORE
WIRED REMOTE
CONTROLLER
DRY
CONTACT
BODY OF THE CONTROL BOX
BR
1(L) 2(N) 3
TO OUTDOOR UNIT
GN/YL
CN-CC
BR
BL
CN-PIPE
CN-ROOM
CN-REMO CN-PTC
BL
5
6
INDOOR MOTOR
(1 & 2)
MAIN PCB ASSEMBLY
4
BK
WH
RD
BL
NE
-ZO
CN-POWER
FUSE250V
10A
LOW MED HI COMP3 COMP2 COMP1
CN-TAB
BL
CN-MOTOR1
T
OA
-FL
CN
RY-D/PUMP
CN-D/PUMP
BL BR
CN
CN-OPTION
CN-OUT
BL
DRAIN
PUMP
RD
BL
OPTION PCB
ASSEMBLY
BL
CN-N
BR
CN-L
CN-ZONE
RD
10
9
BL
RD
8
TO OUTDOOR
(SIGNAL)
7
COMP1
COMP2
BK
11
FROM OUTDOOR
UNIT
CN-H/P_1
RD
SUB PCB ASSEMBLY
CN-L/P_1
12
BK
CN-H/P_2
CN-L/P_2
BLUE
GN/YL GREEN/YELLOW BL
YELLOW
RED
RD
BLACK
BK
OR
YL
ORANGE BR
BROWN
WH
GN
WHITE
GREEN
EBY43304426
24
Wiring Diagram
Unit : 102K BTU/H(1 ODU - Single Piping)
In door & Out door connection detail
INDOOR
OUTDOOR
Terminal No.
L3
BLACK
MOTOR
1
C S R
L2
MOTOR
2
C S R
YELLOW
ORANGE
YELLOW
7
8
3Ø415 V
POWER SUPPLY 9
10
11
12
PHASE
NEUTRAL
COMP1
GND
BK
RD 7
20
RD
RD
1
T2
T3 A1
BL
YL
RD
YL 2 BL 3 BK 8
RD
20
RD
9
BLACK
ORANGE
CAPACITOR
1
CAPACITOR
2
BK 11
BK
}
9
10
LP1/HP1
LP1/HP1
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
GND IN
NC
1
2
PHASE
NEUTRAL
IN Door Motor
3
6
COMP1
GND
4
5
LP1/HP1
LP1/HP1
BK 11
TB2
9
BK 8
GN
8
RD
18 15
3ø MONITORING
RELAY
L3 L2 L1
6
5
4
7
7
RD
ENGLISH
OUTDOOR WIRING DIAGRAM
COMP.
L1
1
2
3
4
5
6
7
8
TB1
RD WH
L1 L2 L3 A2
MAGNETIC
CONTACTOR
T1
34
34 RD
35
RD YL
10
11
GN
1
12
2
3
4
5
6
TERMINAL B
TERMINAL A
BL BK GN
L
N
G
NORMAL CROSS-SECTIONAL AREA
WIRE NO.
HP
LP
SWITCH SWITCH
3ø 415V
POWER SUPPLY
TO INDOOR FROM
FROM TO
(1ø,230V) INDOOR INDOOR INDOOR
(SIGNAL) (HP/LP)
INDOOR WIRING DIAGRAM
TO OUTDOOR UNIT
1(L) 2(N) 3
SPECIFICATION
1.0 mm 2
3,4 & 5
1.5 mm 2
1,2 & 6
6.0 mm 2
7,8,9,10 & 11
5 CORE
3 CORE
3 CORE
WIRED REMOTE
CONTROLLER
DRY
CONTACT
BR
BL
CN-PIPE
CN-CC
BR
BL
5
6
INDOOR MOTOR
BK
WH
RD
BL
4
BK
WH
RD
BL
CN-ROOM
CN-REMO CN-PTC
MAIN PCB ASSEMBLY
NE
-ZO
CN-POWER
FUSE250V
10A
LOW MED HI COMP3 COMP2 COMP1
CN-MOTOR1
CN-TAB
BL
T
OA
-FL
CN
RY-D/PUMP
CN-D/PUMP
BL BR
CN
CN-OPTION
CN-OUT
BL
RD
DRAIN
PUMP
OPTION PCB
ASSEMBLY
BL
BR
TO OUTDOOR HP/LP & GND INPUT
(SIGNAL) FROM OUTDOOR
UNIT
CN-N
COMP1
CN-L
CN-ZONE
7
RD
8
GN/YL BODY OF THE
CONTROL BOX
9
RD
10
SUB PCB ASSEMBLY
BK
11
CN-H/P_1
CN-L/P_1
12
GREEN/YELLOW
GN/YL
RED
RD
BLACK
BK
OR
ORANGE BR
YL
YELLOW
BL
BROWN
WH
WHITE
GN
BLUE
GREEN
EBY43304433
23
Wiring Diagram
Unit :102K BTU/H
OUTDOOR WIRING DIAGRAM
COMP(1)
COMP(2)
In door & Out door connection detail
INDOOR
W
BR 7
U
W
V
U
MOTOR
1 R
C
S
MOTOR
2 R YELLOW
C
S
ORANGE
21 21
BL BL
28 25
RD
18 15 20
RD
20
BK WH RD
BK WH RD
1
2
3
4
5
6
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
GND IN
NC
1
7
PHASE
2
8
NEUTRAL
9
GND
10
7
COMP1
11
8
COMP2
3
4
5 IN door motor
6
L3 L2 L1
CAPACITOR
2
6 5 4
BL YL RD
A1
Magnetic 1
Contactor
BK T1 T2 T3
BL YL RD
BK 11
3
PHASE
NEUTRAL
C/B BODY
COMP1
COMP2
3ø MONITORING
RELAY
2
CAPACITOR
1
BK 11
To Indoor
L1 L2 L3
A2
A1
Magnetic 2
Contactor
11 11 T1 T2 T3
BK
9 8 7
BK BL YL RD
LP/HP1
LP/HP1
LP/HP2
LP/HP2
9
10
11
12
13
14
15
16
LP/HP1
LP/HP1
LP/HP2
LP/HP2
YL 27
4
To Indoor
BK 28
GN/YL
16 15
TERMINAL (B)
TERMINAL (C)
38
30
BK
GN/YL
3
BK 9
14 13
TERMINAL (D)
38
12 11 10
30
9
5
7 GND 6
8
4
G N
G
3
2
2
B
1
TERMINAL (A)
1
NORMAL CROSS-SECTIONAL AREA
Y R
WIRE NO.
HP 2
OUTDOOR
Terminal No.
V
3Ø415 V
POWER SUPPLY
BR 7
BL
BLACK
YELLOW
1
L1 L2 L3
A2
BLACK
ORANGE
Magnetic Contactor(1)
Magnetic Contactor(2)
LP 2
HP 1
3Ø415 V
POWER SUPPLY
FROM INDOOR TO INDOOR
1Ø230 V
LP 1
INDOOR WIRING DIAGRAM
SPECIFICATION
1.0 mm 2
13,14,15 &16
1.5 mm 2
7,8,9,10 &11
10 mm 2
1,2,3,4 & 5
5 CORE
5 CORE
4 CORE
WIRED REMOTE
CONTROLLER
DRY
CONTACT
BODY OF THE CONTROL BOX
BR
1(L) 2(N) 3
TO OUTDOOR UNIT
GN/YL
CN-PIPE
CN-CC
BR
BL
CN-ROOM
CN-REMO CN-PTC
BL
5
6
INDOOR MOTOR
(1 & 2)
MAIN PCB ASSEMBLY
4
BK
WH
RD
BL
NE
-ZO
CN-POWER
FUSE250V
10A
CN-D/PUMP
BL
LOW MED HI COMP3 COMP2 COMP1
CN-MOTOR1
CN-TAB
T
OA
-FL
CN
RY-D/PUMP
BL BR
CN
CN-OPTION
CN-OUT
BL
DRAIN
PUMP
RD
BL
OPTION PCB
ASSEMBLY
BL
BR
CN-N
CN-L
CN-ZONE
RD
10
9
BL
RD
8
TO OUTDOOR
(SIGNAL)
7
COMP1
COMP2
BK
11
FROM OUTDOOR
UNIT
CN-H/P_1
RD
SUB PCB ASSEMBLY
CN-L/P_1
12
BK
CN-H/P_2
CN-L/P_2
YL
RED
RD
OR
BLACK
BK
ORANGE BR
YELLOW
GN/YL GREEN/YELLOW BL
BROWN
WH
GN
BLUE
WHITE
GREEN
EBY43304427
22
Wiring Diagram
Unit : 90K BTU/H (1 ODU - Single Piping)
In door & Out door connection detail
INDOOR
OUTDOOR
Terminal No.
L3
BLACK
MOTOR
1
C S R
MOTOR
2
C S R
YELLOW
ORANGE
YELLOW
3Ø415 V
POWER SUPPLY
1
2
3
4
5
6
7
8
PHASE
NEUTRAL
TB1
WH
COMP1
GND
BK
L2
L3 A2
MAGNETIC
CONTACTOR
RD
T2
T3
20 RD
18
BLACK
ORANGE
15
1
YL
2
BL
3
BK
CAPACITOR
1
CAPACITOR
2
BK 11
3 ø MONITORING
RELAY
}
9
10
LP1/HP1
LP1/HP1
7
8
9
10
11
12
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
GND IN
NC
1
2
PHASE
NEUTRAL
IN Door Motor
3
6
COMP1
GND
4
5
LP1/HP1
LP1/HP1
BK 11
TB2
L3 L2 L1
A1
BK
BL 6
YL 5
RD 4
RD
9
8
RD
BK 8
7
RD
GN
7
RD
ENGLISH
OUTDOOR WIRING DIAGRAM
COMP.
L1
L2
RD
RD 7
20 RD
L1
T1
34
34
35
8
10
9
11
GN
12
1
YL
BL
BK
2
3
4
5
6
TERMINAL B
TERMINAL A
RD
L
GN
N
G
NORMAL CROSS-SECTIONAL AREA
WIRE NO.
HP
SWITCH
LP
SWITCH
3 ø 415V
POWER SUPPLY
TO INDOOR
(1 ø,230V)
FROM
FROM
TO
INDOOR INDOOR INDOOR
(SIGNAL) (HP/LP)
INDOOR WIRING DIAGRAM
SPECIFICATION
1.0 mm 2
3,4 & 5
1.5 mm 2
1,2 & 6
6.0 mm 2
7,8,9,10 & 11
5 CORE
3 CORE
3 CORE
WIRED REMOTE
CONTROLLER
DRY
CONTACT
TO OUTDOOR UNIT
BR
1(L) 2(N) 3
CN-PIPE
CN-CC
BR
BL
INDOOR MOTOR
4
WH
RD
BL
BL
BK
BL
5
WH
RD
BL
CN-ROOM
CN-REMO CN-PTC
MAIN PCB ASSEMBLY
6
NE
-ZO
CN-POWER
FUSE250V
10A
LOW MED HI COMP3 COMP2 COMP1
CN-MOTOR1
CN-TAB
BL
T
OA
-FL
CN
RY-D/PUMP
CN-D/PUMP
BL BR
CN
CN-OPTION
CN-OUT
BL
RD
DRAIN
PUMP
OPTION PCB
ASSEMBLY
BL
BR
TO OUTDOOR HP/LP & GND INPUT
(SIGNAL) FROM OUTDOOR
UNIT
CN-N
COMP1
CN-L
CN-ZONE
7
RD
8
GN/YL BODY OF THE
CONTROL BOX
9
RD
10
SUB PCB ASSEMBLY
BK
11
CN-H/P_1
CN-L/P_1
12
GREEN/YELLOW
GN/YL
RED
RD
BLACK
BK
OR
ORANGE
YL
BR
YELLOW
BL
BROWN
WH
WHITE
GN
BLUE
GREEN
EBY43304432
21
Wiring Diagram
Unit : 90K BTU/H
OUTDOOR WIRING DIAGRAM
COMP(1)
W
BR 7
U
W
V
COMP(2)
U
V
In door & Out door connection detail
INDOOR
MOTOR
1 R
C
S
MOTOR
2
C R YELLOW
S
21 21
BL BL
28 25
RD
18 15 20
RD
20
BK WH RD
BK WH RD
3ø MONITORING
RELAY
CAPACITOR
2
6 5 4
BL YL RD
A1
Magnetic 1
Contactor
BK 11
L1 L2 L3
A2
A1
Magnetic 2
Contactor
11 11 T1 T2 T3
BK
9 8 7
BK BL YL RD
LP/HP1
LP/HP1
LP/HP2
LP/HP2
9
10
11
12
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
GND IN
NC
13
14
15
16
LP/HP1
LP/HP1
LP/HP2
LP/HP2
YL 27
3 4
GN/YL
GN/YL
TERMINAL (C)
3
BK 9
30
2 1
TERMINAL (A)
12 11 10 9
7 GND 6
8
5
4
3
2
1
NORMAL CROSS-SECTIONAL AREA
G N B
G
LP 2
1
2
3
4
5
6
1
7
PHASE
2
8
NEUTRAL
9
GND
10
7
COMP1
11
8
COMP2
3
4
5 IN door motor
6
PHASE
NEUTRAL
C/B BODY
COMP1
COMP2
L3 L2 L1
L1 L2 L3
CAPACITOR
1
BL YL RD
BK 11
To Indoor
BK 28 BK
18 17 16 15 14 13
38
38
TERMINAL (B)
30
HP 2
OUTDOOR
Terminal No.
BR 7
3Ø415 V
POWER SUPPLY
BL
BLACK
ORANGE
YELLOW
1 2
A2
BLACK
ORANGE
BK T1 T2 T3
Magnetic Contactor(1)
Magnetic Contactor(2)
HP 1
LP 1
FROM INDOOR TO INDOOR
1Ø230 V
INDOOR WIRING DIAGRAM
Y R
WIRE NO.
3Ø415 V
POWER SUPPLY
SPECIFICATION
1.0 mm 2
13,14,15 & 16
1.5 mm 2
7,8,9,10 & 11
10 mm 2
1,2,3,4 & 5
5 CORE
5 CORE
4 CORE
WIRED REMOTE
CONTROLLER
DRY
CONTACT
BODY OF THE CONTROL BOX
BR
1(L) 2(N) 3
TO OUTDOOR UNIT
GN/YL
BL
CN-CC
BR
CN-PIPE
CN-ROOM
CN-REMO CN-PTC
BL
5
6
INDOOR MOTOR
(1 & 2)
MAIN PCB ASSEMBLY
4
BK
WH
RD
BL
NE
-ZO
CN-POWER
FUSE250V
10A
LOW MED HI COMP3 COMP2 COMP1
CN-MOTOR1
CN-TAB
BL
T
OA
-FL
CN
RY-D/PUMP
CN-D/PUMP
BL BR
CN
CN-OPTION
CN-OUT
BL
DRAIN
PUMP
RD
BL
OPTION PCB
ASSEMBLY
BL
BR
CN-N
CN-L
CN-ZONE
10
9
BL
RD
8
TO OUTDOOR
(SIGNAL)
RD
7
COMP1
COMP2
BK
11
FROM OUTDOOR
UNIT
SUB PCB ASSEMBLY
CN-H/P_1
RD
CN-L/P_1
12
BK
CN-H/P_2
CN-L/P_2
YL
RED
RD
OR
BLACK
BK
ORANGE BR
BROWN
YELLOW WH
GN/YL GREEN/YELLOW BL
GN
BLUE
WHITE
GREEN
EBY43304428
20
Wiring Diagram
Unit : 51K / 66K BTU/H
T3
BLACK
MOTOR
1
C S R
MOTOR
2
C S R
YELLOW
ORANGE
YELLOW
In door & Out door connection detail
INDOOR
RD
1
RD
BK
T2
T3 A1
BL
YL
RD
YL 2 BL 3 BK 8
RD
20
RD
RD
BLACK
ORANGE
18 15
CAPACITOR
1
BK
GN
9
CAPACITOR
2
BK 11
3ø MONITORING
RELAY
L3 L2 L1
6
1
2
4
5
6
3
PHASE
NEUTRAL
COMP
HP/LP
HP/LP
GND
7
8
9
10
11
12
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
GND IN
NC
1
2
3
4
5
6
PHASE
NEUTRAL
COMP
HP/LP
HP/LP
GND
BK 11
TB2
9
5
4
BK 8
7
8
RD YL
OUTDOOR
Terminal No.
3Ø415 V
POWER SUPPLY
TB1
34
7
RD
ENGLISH
OUTDOOR WIRING DIAGRAM
COMP.
T1
T2
RD WH
RD 7
20
L1 L2 L3 A2
MAGNETIC
CONTACTOR
T1
34 RD
35
HP
LP
SWITCH SWITCH
10
11
GN
1
12
2
3
4
5
6
TERMINAL B
TERMINAL A
BL BK GN
3ø 415V
POWER SUPPLY
INDOOR WIRING DIAGRAM
L
N
G
TO INDOOR FROM
FROM TO
(1ø,230V) INDOOR INDOOR INDOOR
(SIGNAL) (HP/LP)
WIRED REMOTE
CONTROLLER
DRY
CONTACT
NORMAL CROSS-SECTIONAL AREA
WIRE NO.
SPECIFICATION
1.0 mm 2
3,4 & 5
1.5 mm 2
1,2 & 6
3.5 mm 2
7,8,9,10 & 11
5 CORE
3 CORE
3 CORE
Indoor Motor Connection Detail
WIRE COLOR FOR SPEED
COMMON
HI SPEED MEDIUM SPEED LOW SPEED
MODEL
1(L) 2(N) 3
CN-PIPE CN-ROOM CN-REMO CN-PTC
BK
YL
BL
BK
LB-E0422QC/4 TON
YL
LB-G0307QC/3 TON
LB-E0552QC/5.5 TON
BK
BL
OR
RD
OR
BL
OR
MAIN PCB ASSEMBLY
GN/YL
4
RD
5
NE
-ZO
CN
6
TO OUTDOOR UNIT TO OUTDOOR
(SIGNAL) (HP/LP)
CN-CC
BR
BR
BL
BL
RD
OR
CN-TAB
RD
CN-POWER
CN-OUT
CN-MOTOR1
FUSE 250V RY-D/PUMP
10A CN-D/PUMP
BL
T
OA
-FL
CN
CN-OPTION
COMP3 COMP2 COMP1
RD BL BK
BL
MEETING HOUSING
LOW MED HI
DRAIN
PUMP
INDOOR
MOTOR
YL BR
OPTION PCB
ASSEMBLY
GN/YL
RD
BK
CN-ZONE
CN-H/P1 CN-L/P1
BR
BL
SUB PCB ASSEMBLY
CN-N
CN-L
GREEN/YELLOW
GN/YL
RED
RD
BLACK
BK
OR
YL
BL
ORANGE BR
YELLOW
WH
GN
BLUE
BROWN
WHITE
GREEN
EBY43304421
19
T2
COMP.
R
1
T1
RD WH
BK
S
2
RD
YL
BL
T2
T1
T2
L1 L2 L3 A2
MAGNETIC
CONTACTOR
T3 A1
T3
BK
RD
18 15
N
8
1
BK
3ø 415V
POWER SUPPLY
T
3
TERMINAL A
N
YELLOW
10
S
11
ORANGE
MOTOR
9
GR/YL
L
BLACK
G
RD
7
3ø MONITORING
RELAY
L3 L2 L1
TERMINAL B
TERMINAL A
BK
RD
T3 A1
BL
3
N
G
7
RD
8
RD
BL
YL
RD
OUTDOOR WIRING DIAGRAM
DRY
CONTACT
L
N
9
BK
BK
COMP.
S
10
11
BK
BK
3ø MONITORING
RELAY
L3 L2 L1
ORANGE
T2
CN-CC
12
TERMINAL C
TERMINAL C
BK
CAPACITOR
1
G
CN-ROOM
13
14
PHASE
NEUTRAL
COMP
HP/LP
HP/LP
GND
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
GND IN
NC
OUTDOOR
9
10
11
13
14
12
1
2
3
7
8
Terminal No.
INDOOR
In door & Out door connection detail
1
2
4
5
6
3
RD
3Ø415 V
POWER SUPPLY
RD
PHASE
NEUTRAL
COMP
HP/LP
HP/LP
GND
RD
1,2,3,7 & 8
1.0 mm 2
1.5 mm 2
3.5 mm 2
3 CORE
5 CORE
SPECIFICATION
9,10 & 12
11, 13 & 14
3ø 415V
TO INDOOR FROM TO
POWER SUPPLY (1ø,230V) INDOOR INDOOR
G
12
TERMINAL C
RD
1(L) 2(N) 3
4
13
5
14
GR/YL
CAPACITOR
1
YELLOW
BLACK
MOTOR
1
1.0 mm 2
9,10, & 12
1.5 mm2
1,2,3,7 & 8
3.5 mm 2
WIRE NO.
RD
PHASE
NEUTRAL
COMP
HP/LP
HP/LP
GND
1
2
4
5
6
3
9
10
11
13
14
12
T3
3Ø415 V
POWER SUPPLY
1
2
3
7
8
INDOOR
YELLOW
GN
WH
ORANGE BR
GREEN
WHITE
3 CORE
11,13 & 14
WIRE NO.
NORMAL CROSS-SECTIONAL AREA
TO INDOOR HP SWITCH LP SWITCH
(HP/LP)
WIRED REMOTE
CONTROLLER
BLUE
T
OA
-FL
OR
CN
CN-REMO CN-PTC
NE
-ZO
CN
YL
CN-ZONE
BLACK
OPTION PCB
ASSEMBLY
CN-OPTION
MAIN PCB ASSEMBLY
CN-PIPE
3ø 415V
TO INDOOR FROM TO
POWER SUPPLY (1ø,230V) INDOOR INDOOR
RD
OR
CN-OUT
GN/YL
LOW MED HI COMP3 COMP2 COMP1
CN-MOTOR1
RD BL BK
INDOOR
MOTOR
YL BR
SUB PCB ASSEMBLY
RED
BROWN
BK
BL
Wiring Diagram
Unit : 36K BTU/H
2
BL
YL
RD
OUTDOOR WIRING DIAGRAM
T1
S
YL
T1
1
T
L1 L2 L3 A2
MAGNETIC
CONTACTOR
RD WH
RD
R
3ø 415V
POWER SUPPLY
CN-TAB
BL
DRAIN
PUMP
CN-L
CN-H/P1 CN-L/P1
FUSE 250V RY-D/PUMP
10A CN-D/PUMP
RD
BK
BL
INDOOR WIRING DIAGRAM
BR
BR
BL
BL
GN/YL
RD
RD
CN-POWER
BR
BL
CN-N
RD
GREEN/YELLOW
EBY43304422
GN/YL
18
EBY43304423
3 CORE
5 CORE
3 CORE
NORMAL CROSS-SECTIONAL AREA
SPECIFICATION
TO INDOOR HP SWITCH LP SWITCH
(HP/LP)
TERMINAL B
RD
RD
18 15
TERMINAL C
BK
PHASE
NEUTRAL
COMP
HP/LP
HP/LP
GND
PHASE IN ( R )
PHASE IN ( Y )
PHASE IN ( B )
NEUTRAL IN
GND IN
NC
In door & Out door connection detail
Terminal No.
OUTDOOR
TO OUTDOOR UNIT TO OUTDOOR
(SIGNAL) (HP/LP)
6
4. Connecting Pipes to the Outdoor Unit
1.8kg.m
1/4"
Torque
Pipe size
6.6kg.m
5/8"
5.5kg.m
1/2"
ENGLISH
1) Connecting the pipes to the
Outdoor unit
1. Align the center of the pipingsand
sufficientlytighten the flare nut with
fingers.
2. Finally, tightenthe flare nut with torque
wrenchuntilthe wrenchclicks.
• When tightening the flare nut with torque
wrench, ensure the direction for
tightening follows the arrow on the
wrench.
4.2kg.m
3/8"
6.6kg.m
3/4"
Outdoor unit
Gas side piping
(Bigger Dia.)
Liquid side piping
(Smaller Dia.)
Torque wrench
5. Checking the Drainage
1) Checking the Drainage
1. Remove the Air Filter.
2. Check the drainage.
• Spray one or two glasses of water upon
the evaporator.
• Ensure that water flows drain hose of
indoor unit without any leakage.
17
6) Pipe bending
Annealed copper pipe with small diameter (ø6.35 or ø9.52) can be easily bent manually. In
this case, secure large R(radius) for the bend section and gradually bend pipe. If annealed
copper pipe is large in diameter (ø12.7, ø15.88 or ø19.05), bend pipe with bender. Use bender
appropriate for the pipe diameter.
7) Brazing
In refrigerant piping, bending (in particular, acute bending) must be minimized to reduce
piping resistance. Bending is, however, necessary in some places by virtue of the installation
position of devices or of the building structure, piping distance or finishing appearance.
Perform brazing using ready-made elbow. Aside from this function, brazing
perform brazing using ready-made elbow. Aside from this function, brazing
also serves to connect straight pipes, generally using ready-made sockets. While brazing,
protect piping against heat with wet cloth to avoid damaging valve packing or burning
thermal insulator with burner heat. While brazing, blow inert gas (nitrogen gas or carbonic
gas) to prevent formation of oxidation film in copper piping; otherwise, the refrigerant circuit
will clog. The blowing of nitrogen gas (or carbonic gas) through 3-way valves is described in
the following:
8) Refrigerant piping(Flare piping)
When connecting piping, be sure to keep piping dry(keep piping away from water), clean
(keep piping away from dust) and airtight (avoid refrigerant leakage).
When connecting piping on rainy days or making a through-hole in wall, take due care to
prevent water or plaster from entering piping.
Water enters
Plaster enters
CAUTION
a. This procedure is designed to prevent formation of oxidation film by filling piping with
inert gas. Note that excessive gas pressure will generate pinholes at brazed points.
(Nitrogen gas: Supply pressure
0.05~0.1kg/cm2G)
b. When supplying inert gas, be sure to open one end of piping.
16
3. Connecting Pipes to the Indoor Unit
Copper
tube
90➀
Slanted Uneven Rough
ENGLISH
3-1. Preparation of Piping
Main cause of gas leakage is defect in
flaring work. Carry out correct flaring work
in the following procedure.
1) Cut the pipes and the cable.
nUse the accessory piping kit or the pipes
purchased locally.
nMeasure the distance between the
indoor and the outdoor unit.
nCut the pipes a little longer than
measured distance.
nCut the cable 1.5m longer than the pipe
length.
Pipe
Reamer
Point down
2) Burrs removal
nCompletely remove all burrs from the cut
cross section of pipe/tube.
nPut the end of the copper tube/pipe to
downward direction as you remove burrs
in order to avoid to let burrs drop in the
tubing.
Flare nut
Copper tube
3) Putting nut on
nRemove flare nuts attached to indoor
and outdoor units, than put them on
pipe/tube having completed burr
removal.
(Not possible to put them on after flaring
work)
4) Flaring work
nCarry out flaring work using flaring tool
as shown below.
Outside Diameter
1/4"
3/8"
1/2"
5/8"
3/4"
"A"
0~0.5
0.5~0.8
0.5~0.8
0.8~1.0
1.0~1.3
Handle
Bar
Bar
"A"
Yoke
Cone
Copper pipe
Clamp handle
Red arrow mark
Smooth all round
Inside is shining without scratches.
Firmly hold copper tube in a bar(or die) as
indicated dimension in the table above.
= Improper flaring =
5) Check
Ð Compare the flared work with figure.
If flare is noted to be defective, cut off
the flared section and do flaring work
again.
Inclined Surface Cracked Uneven
damaged
thickness
Even length
all round
15
ELECTRICALWIRING
Perform the electrical wiring work according to
the electrical wiring connection.
• All wiring must comply with local
requirements.
• Select a power source that is capable of
supplying the current required by the air
conditioner.
• Use a recognized circuit breaker
between the power source and the unit.
A disconnection device to adequately
disconnect all supply lines must be
fitted.
Main
power source
Circuit Breaker
Switch box
Outdoor
Indoor
• Capacity of circuit breaker
Capacity
MCB Rating (3 Phase)
125A
264K BTU/h
80A
198K BTU/h
63A
132K BTU/h
50A
102K BTU/h
40A
90K BTU/h
32A
66K BTU/h
32A
51K BTU/h
25A
36K BTU/h
Control terminal board
Control box
A view
A
Cord clamper
Remote
control cord
Connection
cord between
the indoor unit
and the
outdoor unit
1
WIRING CONNECTION
INDOOR UNIT
1
• Remove the control box cover for
electrical connection between the
indoor and outdoor unit.
(Remove crews)€
• Use the cord clamper to fix the cord.
Control box cover
(On which the Electric
Wiring Connection is put)
OUTDOOR UNIT
Main terminal board
• Remove the control cover for wiring
connection.
• Use the cord clamper to fix the cord.
• Earthing work
Connect the cable of diameter 1.6mm2
or more to the earthing terminal provided
in the control box and do earthing.
Control terminal board
Please check !!
Cover control
Cord
clamper
14
REFRIGERANT PIPING
Perform the work according to the Service
Manual or Installation Guide.
Factory charged gas
Braze the connection pipes
ENGLISH
• Braze the joints
• Perform air purge with R-22 or vacuum
drying.
• When piping work is finished, check all
joints.
n Add refrigerant if piping is over 7.5m.
Use hard pipe
Outdoor
U-Trap
(See page 4 for details)
• U-trap is to be provided for every 5 mtr.
increase in the vertical length of the pipe.
Indoor
Braze the connection pipes
INSTALLATION OF OUT DOOR UNIT
nSelect the following location
• A place where the air conditioner can
get good ventilation.
• A place where it shall not annoy the
neighbors.
• A place where the unit shall be leveled
and that can support the weight of unit
and withstand its vibrations.
Select a location that satisfies the following
conditions. Install the unit firmly in place.
Above 100Cm
Outdoor unit
Above 50Cm
Above 100Cm
Above 50Cm
Face of wall
n Keep a maintenance space
13
INSTALLATION OF REMOTE CONTROL BOX
Install the remote control box
and cord correctly.
POINT OF REMOTE CONTROLLER INSTALLATION
• Although the room temperature sensor is in the indoor unit, the remote control box should
be installed in such places away from direct sunlight and high humidity.
• Keep the remote control cord away from
the refrigerant piping and the drain
piping.
• To protect the remote control cord from
electrical noise, place the cord at least
5cm away from other power cables.
(Audio equipment, Television set, etc)
• If the remote control cord is secured to a
wall, provide a trap at the top of the cord
to prevent water droplets from running.
• Select places that is not splashed by
water.
• Select control position after receiving
customer approval.
• The room temperature sensor of the
thermostat for temperature control is
built in the indoor unit.
• This remote controller equipped with
liquid crystal display. If this position is
higher or lower, display is difficult to see.
(The standard height is 1.2~1.5m high)
ROUTING OF THE REMOTE CONTROL CORD
INSTALLATION OF THE REMOTE CONTROL BOX
ELECTRICAL WIRING TO THE INDOOR UNIT
Remote controller
CN REMO
(Main board)
CN REMO
Make sure that wire and terminal
numbers are matched on unit side
and remote controller side.
The maximum length of the cord is 100m.
If the length of the cord exceeds 50m, use a wire size greater than 0.5mm2.
DISASSEMBLING OF THE REMOTE CONTROLLER
Th
el
Front case
ow
er
pa
rt
Lever carefully
the box open
using a screw
driver, etc.
Remote
control
box body
WHEN THE REMOTE CONTROL BOX IS
INSTALLED WITH THE CORD BURIED.
WHEN THE REMOTE CONTROL BOX IS
INSTALLED WITH THE CORD EXPOSED.
PROCEDURE OF INSTALLATION
1. Fix the under plate on the wall by self tapping
screws (accessory).
2. Make a slit (Part A) at the top side of the remote
control box by nipper.
3.Rout the cord as shown in the following figure. In
this case, push the cord into the around of
case(Part B).
4. Hook the remote control unit on the under plate.
PROCEDURE OF INSTALLATION
1. Fix the under plate on the switch box by
screws(Local supply). In this case, fit the under
plate on the wall, and be careful of deformation.
2. Receive the remote control cord in the switch box.
3. Hook the remote control unit on the under plate.
Remote
control cord
(Part A)
Face of wall
Upper notch
Under plate
Tapping screw
(Local supply)
Upper flange
Push hand
(Part B)
Remote
control unit
Face of wall
Upper notch
Under plate
Remote
control unit
Screw
(Local supply)
Remote
control cord
Lower notch
Switch box
(Local supply)
Lower notch
Cord
clamp
FIXING OF REMOTE
CONTROL CORD
1. Fix the cord clamps on the wall
by ø3 tapping screws(Local supply).
2. Fix the remote control cord.
12
ENGLISH
• For every 5 mitrs. increase in vertical length of the piping, U-Trap is to be provided.
11
lDrill the piping hole with 70mm dia, hole
core drill.
lPiping hole should be slightly slant to the
outdoor side.
Indoor
WALL
Outdoor
5~7mm
INSULATION, OTHERS
THERMAL INSULATION
Insulate the joint and tubes completely.
All thermal insulation must comply with local requirement.
INDOOR UNIT
Liquid pipe
Refrigerant pipe and thermal
insulator (Local supply)
Hose crip for thermal insulator
(Local Supply)
Thermal insulator for refrigerant pipe
Local supply)
Gas pipe
REFRIGERANT PIPE
l
l
Insulate gas side pipe
No insulation of liquid pipe
Gas Side
Note :
l Filter Driers, recommended to be used with the unit,
are to be fitted in the liquid line using flare nuts, near
the respective indoor units at a position
where they are accessable for servicing.
l The direction of flow of the refrigerant must
Liquid Line
(To the Evaporator)
match the flow direction indicator on the
filter driers.
Direction of the flow of the Refrigeran t
Filter Drier
Liquid Line
(From the Condenser outlet)
TEST AND CHECK
After all workings are finished, check the working and operation.
l Air distribution
l Drain
Gas leakage
Wiring
Is the air circulation good?
Is the drainage smoothly and no sweating?
Is the piping connection correctly?
Is the wiring connection correctly?
l
l
10
CAUTION
ENGLISH
1. Install declination of the indoor unit is very important for the drain of the duct type air
conditioner.
2. Minimum thickness of the insulation for the connecting pipe shall be 5mm.
Front of view
• The unit must be horizontal or declined to the drain hose connected when finished
installation.
Ceiling
5~8mm
CORRECT
INCORRECT
Drainage hole
CAUTION FOR GRADIENT OF
UNIT AND DRAIN PIPING
Drainage hole
Lay the drain hose with a downward
inclination so water will drain out.
Thermal insulator
(Local supply)
• Always lay the drain with downward
inclination (1/50 to 1/100).
Prevent any upward flow or reverse flow
in any part.
• 5mm or thicker formed thermal insulator
shall always be provided for the drain
pipe.
Drainage pipe
(Local supply)
Unit
Make sure to be closed.
Drainage hole
• Upward routing not
allowed
CORRECT
INCORRECT
Applied U-Trap Dimension
• Install the P-Trap (or U-Trap) to prevent
a water leakage caused by the blocking
of intake air filter.
A 70mm
B 2C
C 2 x SP
SP = External Pressure
(mmAq)
Ex) External Pressure
= 10mmAq
A 70mm
B 40mm
C 20mm
B
C
U-Trap
A
9
• Select and mark the position for fixing
bolts.
• Drill the hole for set anchor on the face
of ceiling.
• Insert the set anchor and washer onto
the suspension bolts for locking the
suspension bolts on the ceiling.
• Mount the suspension bolts to the set
anchor firmly.
• Secure the installation plates onto the
suspension bolts (adjust level roughly)
using nuts, washers and spring
washers.
Old building
New building
1 Set anchor
2 Plate washer
3 Spring washer
4 Nut
5 Suspension
bolts
• Local supply
Set anchor
Plate washer
Spring washer
Nut
Suspension bolt
(36K-132K) (198K-264K)
- M10
- M10
- W3/8 or M10
- W3/8 or M10
M16
M16
M16
M16
CAUTION
Tighten the nut and bolt to prevent unit falling.
8
2. Indoor unit installation
• A place where the unit will be leveled and
that can support the weight of the unit.
• A place where the unit can withstand its
vibration.
• A place where service can be easily
performed.
A
B
ENGLISH
nInstallation of Unit
Install the unit above the ceiling
correctly.
POSITION OF SUSPENSION BOLT
• Apply a joint-canvas between the unit and
duct to absorb unnecessary vibration.
• Apply a filter Accessory at air return hole.
• Install the unit leaning to a drainage hole
side as a figure for easy water drainage.
(G)
I
POSITION OF CONSOLE BOLT
C
E
D
F
5-8 mm
H
Drainage hole
M10 Nut
X4
(Local
M10 SP. washer X 4 supply)
X4
M10 washer
M16 NUT X 3 X 4
M10 washer
X4
(Local
M10 SP. washer X 4 supply)
X4
M16 SPRING WASHER X 3 X 4
M16 WASHER X 3 X 4
M10 Nut
For 198K-264K
7
Outdoor Unit
The heat exchanger coils and panel vents of the outdoor unit should be checked regularly. If clogged
with dirt or soot, the heat exchanger and panel vents may be professionally steam cleaned.
Note:
Dirty or clogged coils will reduce the operating efficiency of the system and cause higher operating costs.
Outdoor Unit
D
W
D
(Side)
H
H
(Rear)
W
Air intake
vents
Control Cover
Connecting Wire
Air outlet
vents
Indoor Unit
Connection Pipe
Drain Hose
AIR FILTER
AIR INTAKE VENTS
W
D
CONTROL
BOX
H
AIR
OU
REMOTE
CONTROLLER
TL
ET
V
EN
T
S
(For 198K & 264K Unit)
Dimension
Capacity
36K BTU/H
51K BTU/H
51K BTU/H
66K BTU/H
66K BTU/H
66K BTU/H
90K BTU/H
* 90K BTU/H
102K BTU/H
* 102K BTU/H
* 102K BTU/H
132K BTU/H
132K BTU/H
132K BTU/H
* 132K BTU/H
198K BTU/H
264K BTU/H
Model
LB-G0307QC
LB-E0423QC
LB-R0420QC
LB-E0552QC
LB-R0550QC
LB-R0551QC
LB-H0752QC
LB-80750QC
LB-H0853QC
LB-80850QC
LB-80851QC
LB-J1104QC
LB-J1103QC
LB-J1105QC
LB-81100QC
LB-K1653QC
LB-M2200QC
Indoor Unit (mm)
IDU
W
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
D
1180
1230
1230
1230
1230
1230
1564
1562
1564
1562
1562
1700
1700
1700
1562
1985
2050
480
600
590
600
590
590
660
688
660
688
688
690
690
690
688
865
1080
Outdoor Unit (mm)
H
870
906
906
906
906
899
906
906
906
906
995
970
906
970
995
906
970
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
3
2
W
ODU
295
370
380
370
380
380
460
460
460
460
460
460
460
460
460
595
640
D
320
406
406
406
406
355
600
600
600
600
475
570
406
670
475
406
570
H
655
1135
1135
1135
1135
1135
1135
1135
1135
1135
1360
1310
1135
1310
1360
1135
1310
* is applicable for single piping model only.
6
Care and
maintenance
Care and maintenance
Air filters
q Never use any of the followings:
• Water hotter than 40°C
Could cause deformation and/or
discoloration.
• Volatile substances
Could damage the surfaces
of the air conditioner.
N NER
n zene
ENGLISH
Caution: Before performing any maintenance, turn off the main power to the system.
Indoor Unit
Grille, Case, and Remote Control:
q Turn the system off before cleaning. To clean,
wipe with a soft, dry cloth. Do not use bleach or
abrasives.
Note:
Supply power must be disconnected before
cleaning the indoor unit.
SI
Be
Air outlet vent
Air Filter:
The air filters behind Indoor unit
(the suction side) should be checked and cleaned
once every 2 weeks or more often if necessary.
SCO
U RIN G
C LB
A R GER
q Cleaning Tips:
1
Clean the filter with a vacuum or warm, soapy
water.
• If very dirty, wash with a solution of
detergent in lukewarm water.
• If hot water (50°C or more) is used, filter
may be deformed.
Re-install the air filter.
3
After washing with water, dry well in the shade.
2
Air outlet vent
Indoor Unit Dimensions (mm)
Dimension
Capacity
Model
A
B
C
D
E
F
G
H
I
LB-R0420QC 1291 1230 380 57.5 590 30 130 1005 232
51K BTU/H
LB-E0423QC 1291 1230 565 57.5 680 30 294 1025 312
51K BTU/H
LB-G0307QC 1240 1180 365 57.5 480 30 290 850 205
36K BTU/H
66K BTU/H
66K BTU/H
LB-E0552QC 1291 1230 485 57.5 600 30 294 1025 312
LB-R0550QC/
1291 1230 380 57.5 590 30 130 1005 232
LB-R0551QC
LB-H0853QC
LB-80850QC
LB-80851QC
LB-J1105QC
LB-81100QC
*132K BTU/H
LB-R0750QC 1625 1562 510 65
* 90K BTU/H
LB-H0752QC 1625 1564 510 65
90K BTU/H
102K BTU/H
*102K BTU/H
132K BTU/H
660 30 294 1220 304
688 30 294 1220 304
688 30 294 1220 304
1625 1562 510 65
660 30 294 1220 304
1625 1564 510 65
688 30 294 1220 304
1625 1562 510 65
692 30 294 1220 304
1765 1705 597 55
LB-M2200QC 2110 2050 920 55 1080 22 294 1488 494
264K BTU/H
LB-K1653QC 1987 1930 755 55
198K BTU/H
865 30 294 1260 422
Slope 5-8 mm
* is applicable for single piping model only.
• Slope of about 5-8 mm is to be provided at the
drain hole side of the indoor unit for proper
drainage.
• After installation the slope can be measured
using a sprit level.
5
2. Installation of Indoor, Outdoor Unit
1. Selection of the best location
1) Indoor unit
Select location
Install the air conditioner in the location that
satisfies the following conditions.
• The place shall easily bear a load exceeding
four times the indoor unit’s weight.
• The place shall be able to inspect the unit as
the figure.
• The place where the unit shall be leveled.
• The place shall allow easy water
drainage.(Suitable dimension “H” is necessary
to get a slope to drain as figure.)
•The place shall easily connect with the
outdoor unit.
• The place where the unit is not affected by an
electrical noise.
• The place where air circulation in the room will
be good .
• There should not be any heat source or steam
near the unit
Top view
(unit: mm)
600
Inspection hole
(600X600)
Control box
1000
1000
Front
Front view
H
2) Outdoor unit
• If an awning is built over the unit to prevent
direct sunlight or rain exposure, be careful
that heat radiation from the condenser is not
restricted.
• There should not be any animals or plants
which could be affected by hot air
discharged.
• Ensure the spaces indicated by arrows from
the wall, ceiling, fence or other obstacles.
3) Piping length and the elevation
Capacity
36K BTU/h
51K BTU/h
66K BTU/h
90K BTU/h
* 90K BTU/h
102K BTU/h
* 102K BTU/h
132K BTU/h
132K BTU/h
* 132K BTU/h
198K BTU/h
264K BTU/h
Indoor Outdoor
Unit
Unit
(nos)
(nos)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
1
2
Pipe Size
(Diameter : Ø)
Liquid
Gas
5/8"
3/8"
3/4"
1/2"
7/8"
1/2"
3/4"
1/2"
1-1/8"
5/8"
9/8"
1/2"
1-1/8"
5/8"
7/8"
1/2"
7/8"
1/2"
1-1/8"
5/8"
7/8"
1/2"
1-1/8"
5/8"
Length A(m)
Standard
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
Max.
30
30
30
30
30
30
30
30
30
30
30
30
Elevation B(m)
Standard
5
5
5
5
5
5
5
5
5
5
5
5
Max.
10
10
10
10
10
10
10
10
10
10
10
10
*Additional
refrigerant
(g/m)
40
60
70
70
70
70
70
70
70
70
70
100
Indoor unit
A
B
Outdoor unit
* is applicable for single piping model only.
• Capacity is based on standard length and maximum allowance
length is on the basis of reliability.
• 36K BTU/h model indoor liquid line 1/4" to be swaged to 3/8" liquid
line of ODU.
4
1. The following should be always observed for safety
Could lead to death, serious injury, etc.
WARNING
ENGLISH
• Please report to or take consent by the supply authority before connecting to the system.
• Be sure to read "THE FOLLOWING SHOULD BE ALWAYS OBSERVED FOR SAFETY" before
installing the air conditioner.
• Be sure to observe the cautions specified here as they include important items related to safety.
• The indications and meanings are as follows.
Could lead to serious injury in particular environments when operated incorrectly.
CAUTION
• After reading this manual, be sure to keep it together with the owner's manual in an accessible
place.
WARNING
Do not install it yourself (customer).
Perform the installation securely referring to the
installation manual.
Attach the electrical part cover to the indoor unit and
the service panel to the outdoor unit securely.
Use the specified wires to connect the indoor and the
outdoor units securely and attach the wires firmly to
the terminal board connecting sections so the stress
of the wires is not applied to the sections.
• If the capacity of the power circuit is insufficient or there is
incomplete electrical work, it could result in a fire or an electric
shock.
• When installed in an insufficient strong place, the unit could fall
causing injured.
Perform electrical work according to the installation
manual and be sure to use an exclusive circuit.
Install the unit securely in a place which can bear the
weight of the unit.
• Incomplete installation could cause a personal injury due to
fire, electric shock, the unit falling or a leakage of water.
• Incomplete installation could cause injury due to fire, electric shock,
the unit falling or a leakage of water. Consult the dealer from whom
you purchased the unit or special installer.
• Incomplete connecting and fixing could cause fire.
• If the electrical part cover if the indoor unit and/or the service
panel if the outdoor unit are not attached securely, it could result
in a fire or electric shock due to dust, water, etc.
Be sure to use the part provided or specified parts for
the installation work.
Check that the refrigerant gas do not leak after
installation is completed.
• The use of defective parts could cause an injury or leakage of
water due to a fire, electric shock, the unit falling, etc.
CAUTION
Perform the drainage/piping work securely
according to the installation manual.
Do not install the unit in a place where an
inflammable gas leaks.
• If there is a defect in the drainage/piping work, water
could drop from the unit and household goods could be
wet and damaged.
• If gas leaks and accumulates in the area surrounding the unit, it
could cause an explosion.
3
OUT-LINE OF INSTALLATION
1.The following should be always observed for safety............................... 3
Installation works
Installation Parts
Required tools
2. Installation of Indoor, Outdoor Unit........................................................... 4
• Four Type “A” screws
• Level
• Screw driver
• Connecting cable
• Electric drill
• Hole core drill (ø70mm)
1) Selection of the best
location............................4
2) Indoor unit installation.... 5
3. Connecting Pipes to the Indoor Unit........................................................15
1) Preparation of Piping...15
•
• Flaring Tools set
• Pipe is to be used for
Pipes: Gas side ..... 3/4", 5/8", 7/8", 1-1/8"
Liquid side ............. 1/4", 1/2", 5/8", 3/4"
• Insulated drain hose
• Insulation materials
installing 5.5 TR
4. Connecting Pipes to the Outdoor Unit.....................................................17
• Additional Drain hose
1) Connecting the pipes to
the Outdoor Unit ..........17
(Inner Dia...............25mm)
5. Checking the Drainage...............................................................................17
6. Connecting Cables between Indoor Unit and Outdoor Unit.................. 27
• Screw driver
1) Connecting cables to the
Indoor Unit ...................27
2) Connecting cables to the
Outdoor Unit ................28
3) Form the pipings ..........29
7. Air Purging of the Connecting Pipes and the Indoor Unit..................... 30
• Hexagonal Wrench (4mm/5mm)
• Gas-leak Detector
8. Group Control ............................................................................................ 31
9. Two Thermistor System ............................................................................. 31
2
ENGLISH
CEILING DUCT TYPE AIR CONDITIONERS
INSTALLATION INSTRUCTIONS
• Please read this instruction sheet completely before installing the product.
• When the power cord is wanted to replace, replacement work shall be performed by authorized
personnel only.
• Installation work must be performed in accordance with national wiring standards by authorized
personnel only.
Indoor Unit
Air outlet vents
Air intake vents
Air filters
Remote Controller
Outdoor Unit
(Side)
(Rear)
Air intake vents
Air outlet vents
Control cover
Connecting wire
Piping
Drain hose
(Rear)
(Side)
Air intake
vents
Control Cover
Connecting Wire
Air outlet
vents
Connection Pipe
Drain Hose
LG Electronics India Pvt. Ltd.
Regd. Office : A-27, Mohan Cooperative Industrial Estate, Mathura Road, New Delhi-110044.
Download PDF

advertising