LG | AS95GDWT0 | LG AS95GDPT0 Owner’s Manual

OWNER'S MANUAL
AIR PURIFIER
Read this owner’s manual thoroughly before operating the
appliance and keep it handy for reference at all times.
Model name: AS95GD Series
MFL69726823
Rev.00_092117
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 1
www.lg.com
Copyright © 2017 LG Electronics. All Rights Reserved.
2017-09-21 �� 3:47:32
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 2
2017-09-21 �� 3:47:32
Table of Contents
This manual is produced for a group of
products and may contain images or content
different from the model you purchased.
This manual is subject to revision by the
manufacturer.
Safety Instructions......................... 04
Smart Functions............................. 32
Disposal of your Old Appliance (as per
e-waste Rules)......................................10
Using the Smart ThinQ Application......32
Diagnosis Using Sound........................34
Unpacking........................................ 12
Maintenance.................................... 35
Parts.....................................................12
Removing Packing Materials................13
Remote Control Setup..........................15
Installation....................................... 16
Cleaning the Exterior ...........................36
Cleaning the Filter................................37
Replacing the Filter...............................37
Cleaning the Dust Sensor....................38
Storage ................................................39
Transporting or Moving the Product.....16
Installing the Product............................16
Before Calling for Service............ 40
Operation......................................... 17
Product Specifications.................. 44
Product Overview.................................17
Getting Started.....................................23
Using Smart Mode................................23
Using Booster Mode.............................24
Using Dual Mode..................................24
Using Single Mode...............................25
Adjusting the Fan Speed......................25
Adjusting the Clean Booster Fan Speed
..............................................................26
Rotating the Clean Booster..................26
Checking the Air Quality.......................27
Using the Air Ionizer.............................30
Setting the Sleep Timer........................30
Locking the Control Panel Buttons.......31
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 3
Warranty........................................... 45
2017-09-21 �� 3:47:33
Safety Instructions
READ THESE INSTRUCTIONS CAREFULLY
This guide contains many important safety messages. Always read and obey all safety messages.
This is the safety alert symbol. It alerts you to safety messages that inform you of hazards
that can kill or hurt you or others, or cause damage to the product.
All safety messages will be preceded by the safety alert symbol and the hazard signal word
WARNING or CAUTION. These words mean:
WARNING - You can be killed or seriously injured if you do not follow these instructions.
CAUTION - Indicates an imminently hazardous situation which, if not avoided, may
result in minor or moderate injury or product damage.
This equipment is home (class B) EMI suitable equipment, which is mainly for home use, and it can
be used in all regions.
Warning
To reduce the risk of fire, electric shock or personal injury when
using this product, follow basic safety precautions including the
following:
CHILDREN IN THE HOUSEHOLD
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
INSTALLATION
••Install the product near an easily accessible electrical outlet.
••Do not install the product on an uneven or inclined surface.
••Do not install the product in a damp area and keep away from
splashing rain or water.
04
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 4
2017-09-21 �� 3:47:33
••Do not install the product in an area exposed to direct sunlight or
near heat-generating equipment.
••Do not install the product in a place where combustible gas may
leak or industrial oil or metallic particulates are present.
POWER
••This product is for AC 220–240 V. Always check the supply
voltage before using it.
••Be careful not to let the power plug pressed by the back of the
product.
••Remove the power plug when you clean the product or replace
the filter.
••Do not touch the power plug with wet hands.
••Insert the plug into the outlet tightly after removing the moisture
and dust on it completely.
••When unplugging the power cord, always pull it by the plug.
••Unplug the product during thunder or lightning or when not in
use for a long time.
••Do not bend the power cable excessively or place a heavy
object on top of it.
••Do not extend the length of the power cable or alter it.
••Do not use several devices on a multi-socket extension outlet.
••The appliance shall be disconnected from its power source
during service and when replacing parts.
••Take care to ensure that power cable could not be pulled out or
damaged during operation. There is risk of fire or electric shock.
05
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 5
2017-09-21 �� 3:47:33
••If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified person using
only genuine replacement parts in order to avoid a hazard.
USE
••If the product is immersed in water, stop using it and contact the
LG Electronics service center.
••If there is a gas leakage (isobutane, propane, LNG, etc.), do
not touch the product or power plug and ventilate the area
immediately.
••Do not clean the product with brushes, cloths or sponges with
rough surfaces or which are made of metallic material.
••If you detect any abnormal noise, odor or smoke, unplug the
product immediately and contact an LG Electronics service
center.
••Only an authorized repair person from LG Electronics service
center should disassemble, repair, or modify the product.
••Do not use or store fire, combustibles (ether, benzene, alcohol,
drugs, propane, butane, combustible spray, insecticide, air
freshener, cosmetics etc.) or flammable materials (candles,
lamps etc.) near the product.
••Do not place the power cord under rugs, carpeting or mats.
••Do not allow animals or pets to chew on the power cord.
••Do not allow children to climb on or play with the product.
••Do not move the product when it is in operation.
••Do not place coffee, flower vase or drinks on top of the product.
••Do not insert hands or metal objects into the air inlet or outlet.
••Do not impact the product.
06
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 6
2017-09-21 �� 3:47:33
••Be careful not to allow any part of your body to be pinched when
you detach and re-attach parts of the product.
••Unplug the product when not in use for a long time.
••Do not install and use broken parts.
••Do not clean the product when it is plugged in.
••Do not put flammables into the product.
••Do not operate the product while its cover is open.
DISPOSAL
••Dispose of the packing materials (vinyl, styrofoam etc.) to keep
them out of reach of children.
07
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 7
2017-09-21 �� 3:47:33
Caution
To reduce the risk of fire, electric shock, or personal injury when
using the product, follow basic safety precautions, including the
following:
INSTALLATION
••Do not tilt the product to pull or push it while transporting.
••Do not install the product in transportation equipment (vehicle/
vessel etc.).
••Do not place the product near a TV or a stereo equipment.
••Do not place the product under bright light.
••The appliance shall be installed in accordance with national
wiring regulations.
USAGE
••Do not use the product for removal of toxic gas such as carbon
monoxide.
••Do not use the product for ventilation purposes.
••Do not use the product for a long time in a region with unstable
voltage.
••Do not place obstacles around the air inlet or outlet.
••For safe use of the product, children or others with reduced
mental capabilities need to be closely monitored by a person
who is responsible for their safety.
••Do not place the product near curtains.
••Do not use the product for special purposes such as preserving
plants, precision instrument, artworks etc.
••Do not climb or place objects on top of the product.
08
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 8
2017-09-21 �� 3:47:33
••Do not operate the product with wet hands.
••Do not let the moisture from the humidifier directly touch the
product.
••Do not use the product while it is not in upright position.
••Do not use the product near objects vulnerable to heat.
••Use the filter only for its intended purpose.
••Do not use detergents, cosmetics, chemicals, air fresheners, or
disinfectants in the product.
••Do not place magnetic or metal objects on top of the product.
••Do not clean with strong detergents of solvent types, but use
soft cloth.
••Do not operate the Booster arbitrarily.
••Do not insert any objects into the Booster.
••Do not operate the product while the Booster cover and grill are
separated.
••Do not insert hands or metal objects into the Booster.
09
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 9
2017-09-21 �� 3:47:33
Disposal of your Old Appliance (as per e-waste Rules)
1.When this crossed out wheeled bin symbol is depicted on the product and its
operator’s manual, it means the product is covered by the e-waste Management
and Handling Rules, 2011 and are meant to be recycled, dismantled, refurbished
or disposed off.
2.DOs
a.The product is required to be handed over only to the authorized recycle for
disposal.
b.Keep the product in isolated area, after it becomes non-functional/unrepairable
so as to prevent its accidental breakage.
DON’Ts
a.The product should not be opened by the user himself/herself, but only by
authorized service personnel.
b.The product is not meant for re-sale to any unauthorized agencies/scrap
dealer/kabariwalah.
c.The product is not meant for mixing into household waste stream.
d.Do not keep any replaced spare part(s) from the product in exposed area.
3.Any disposal through unauthorized agencies/person will attract action under
Environment(Protection) Act 1986.
4.“This product is complied with the requirement of Hazardous Substances as
specified under Rule 13 (1) & (2) of the E-Waste (Management & Handling)
Rules, 2011.
5.To locate a nearest collection centre or call for pick-up (limited area only) for
disposal of this appliance, please contact Toll Free No.1800-180-9999 for details.
All collection centre and pick up facilities are done by third parties with LG
Electronics India Pvt. Ltd. merely as a facilitator. For more detailed information,
please visit : http://www.lg.com/in
10
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 10
2017-09-21 �� 3:47:33
अपने पुराने निपटान के उपकरण ( ई-अपशिष्ट नियम के अनुसार )
1.जब इस काटे गए पहिये वाले बिन का चिन्ह किसी उपकरण और इसके ओपेरटर की
पुसत
् िका के साथ संलग्न होता है तो इसका मतलब है कि इसे “ई- अपशिष्ट “(प्रबंधन
और हथालन ) नियम २०११ के अंतर्गत सम्मिलित किया गया है , और इसे
नवीनीकरणकरन ,विघटन और निपटान के लिए बनाया गया है ।
2.करें
क . उपकरण को सिर्फ अधिकृत पुनः नवीनीकरणकर्ता को ही निपतारण करने हेतु
हस्तांतरित करें ।
ख. जब उपकरण कार्यरत न हो इसे अलग क्षेत्र में रखें ताकि उपकरण से होने
वाली दुर्घटनाओ से बचा जा सके ।
न करें
क. इस उपकरण को स्वयं/खुद नहीं खोलना चाहिए ! उपकरण को केवल अधिकृत
अधिकारी के द्वारा ही खोला जाना चाहिए ।
ख. इस उपकरण को पुनः बिक्री के लिए किसी भी कबाड़ीवाला / भंगार-वाला /
अनाधिकृत संस्था को न दें ।
ग. इस उपकरण को किसी घरेलू अपशिष्ट सामान के साथ मिलाकर न रखें ।
घ. उपकरण के बदले हुए या आतंरिक पुरजो को खुले क्षेत्र में न रखें ।
3.यदि किसी अनाधिकृत विभाग या व्यक्ति के द्वारा निपटारन किया जाता है तो यह
पर्यावरण (सुरक्षा) धारा १९८६ के अंतर्गत आता है ।
4.यह उत्पाद ई-अपशिष्ट (प्रबंधन और हथालन) नियम 2011 के अन्तर्गत 13(1) एवं (2)
के तहत निर्दिष्ट खतरनाक पदार्थो की आवश्‍यकता का पालन करता है ।
5.उपरोक्त पदार्थो के निपटारन के लिए नजदीकी निपटारन संसथान (संकीर्ण क्षेत्र )में
कॉल करें। अधिक जानकारी के लिए हमारे टोल फ्री नंबर 1800-315-9999 / 1800180-9999 पर कॉल करें. सभी संग्रहण केंद्र व पिक-अप की सुविधाएं किसी थर्डपार्टी जो “LG Electronics India Pvt. Ltd. “को अपनी सेवाएं प्रदान कर रही हों, से
करवाएं ।
ज्यादा जानकारी के लिए देखें वेब:साईट - http://www.lge.com/in
11
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 11
2017-09-21 �� 3:47:33
Unpacking
Parts
Air Purifier
Owner’s
Manual
Remote Control /
Battery (CR2025, 1 Unit)
Owner’s Manual
•• The appearance or components of the product may differ depending on the model.
•• The shape of the power plug differs depending on the country.
12
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 12
2017-09-21 �� 3:47:34
Removing Packing
Materials
4
•• Upper filter inlet: 1 support
Unpack the product and remove any packing
tape or protective vinyl before using the
product.
1
2
•• Lower filter inlet: 2 supports
Pull out the product from the
packaging and remove the fixing tape
attached on the product.
Support
Grab the top end of the back cover
and gently pull it.
•• You will see "PM 1.0 & GAS
SENSOR SYSTEM" on the back
cover of the product.
3
Remove the support located at the
filter inlet.
5
Remove the filter and its protective
vinyl.
6
Install the filter in the product.
Remove the cover from the product.
•• Make sure that the handle faces
upward.
Handle
13
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 13
2017-09-21 �� 3:47:36
7
8
Insert the fixing parts at the bottom of
the cover into the holes at the bottom
of the product before you close the
cover.
Remove the protective vinyl from the
filter at the lower part of the product in
the same way.
Caution
•• Failure to remove the supports may affect
the performance of the product. Please be
sure to remove it before use.
•• Make sure that you remove the filter’s
protective vinyl prior to use otherwise it
may result in product malfunction.
•• Pay attention to the direction of the filter
when you install the filter otherwise it may
cause malfunction or failure of the product.
14
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 14
2017-09-21 �� 3:47:37
Remote Control Setup
1
2
With the backside of the remote
controller facing up, remove the
battery tray from the remote control.
Insert the battery provided with the
product to the tray.
•• The (+) electrode of the battery
must face upward.
Warning
•• A button/coin-shaped battery is used in the
remote control of the product.
•• Do not swallow the battery. It may cause
injury, including damage to the internal
organs or death.
•• If you accidentally swallowed the
battery, go to the doctor immediately for
emergency treatment. If you fail to receive
first aid within 2 hours after you swallowed
it, you may experience damage to your
internal organs or death in severe cases.
•• Keep the battery out of reach of children.
•• If the battery tray is not secured firmly,
stop using the product instantly and keep it
away from children.
Caution
•• Do not modify the battery arbitrarily. It may
cause a fire or electric shock.
•• Misplaced battery may cause an explosion.
3
Insert the battery tray to the remote
control.
Back
•• Do not recharge or take apart the battery.
It may result in explosion.
•• Do not throw the battery in the fire for
disposal or leave it near the heat. It may
result in explosion.
Note
•• If the battery runs out of charge, replace it
with a new one (CR2025).
•• If the remote control does not work as
expected, try to replace the battery or
check the polarity (+, -) of the battery. If
the problem continues, contact the Service
Center.
•• Dispose of the used battery according to
the environmental regulations.
15
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 15
2017-09-21 �� 3:47:38
Installation
Transporting or Moving the
Product
Caution
Transport the product in a well-secured
and upright position. Impacts may cause
product damage.
The product is heavy. Use two people
when moving it.
•• Dropping the product may cause
personal injury or product malfunction.
•• Do not hold the outer cover when you
carry the product. The cover may open
accidentally, causing the product to
drop.
Installing the Product
Caution
Install the product on a strong level
surface. Installing the product on a weak
or tilted surface may cause noise and
vibration or tipping, resulting in injury.
Allow a 1 m clearance between the product
and surrounding surfaces or objects. The
air inlet needs space to function properly.
1m
Do not install the product near curtains
which could block the air inlet or outlet.
Doing so may result in product malfunction
or failure.
When moving or storing the product, wrap
the power cord around the base of the
product to prevent personal injury, damage
to the cord or damage to floors.
The performance of the product may differ
depending on the operating environment
(such as temperature and humidity).
•• 40–70 % of humidity is recommended for
optimal performance.
%
16
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 16
2017-09-21 �� 3:47:39
Operation
Product Overview
Front View
Clean booster
Upper part of the
air purifier
Lower part of the
air purifier
Upper air outlet/Clean booster
Lower air inlet (bottom cover)
•• It discharges purified air through
the upper filter.
•• Air goes into the lower part of the purifier
through the inlet. You may remove the
front or rear cover separately.
•• You can control the direction of the
air so that it reaches every corner
of the room.
Status Panel
Light Lamp
Use it to check the settings of the
product and the air quality.
It displays the overall air quality using
a colored light.
Control Panel
Upper air inlet (top cover)
•• Air goes into the upper part of the
purifier through the inlet. You may
remove the front or rear cover
separately.
Lower air outlet
It discharges purified air through the
lower filter.
Use it to set the product functions.
Receiver for Remote Control Signal
Air Ionizer
•• It generates negative ions and
removes harmful bacteria in the air.
•• It is built in the lower part of the air
purifier.
•• The appearance or components of the product may differ depending on the model.
17
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 17
2017-09-21 �� 3:47:40
Back View
Smart Diagnosis Part
Smell (Gas) Sensor
In the event of a malfunction or failure,
you can use the Smart Diagnosis
option to check the product condition.
(See Smart Functions.)
It detects a smell (gas).
PM 1.0 (super ultra-fine dust)
sensor
Filter
It removes allergic materials, yellow
dust/ultra-fine dust, possible sources
of sick house syndrome, smog and
other odor.
It detects the concentration of dust.
18
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 18
2017-09-21 �� 3:47:41
Filter System
Total Harmful Gas Care Filter
It removes harmful smells (gas) that
are generated in everyday life such
as bathroom smell, cigarette smoke
(smell) and food smell.
Total Allergen Collection Care Filter
It removes super ultra-fine dust,
yellow dust and cigarette smoke
particles from the air.
Ultra-fine Filter
It is attached on the exterior of the
Total Allergen Collection Care Filter,
primarily removing large particles
floating in the air, including pet hair.
Filter Handle
Use it to separate the filter from the
product.
Caution
•• The Total Harmful Gas Care Filter and
Total Allergen Collection Care Filter are
assembled together. Do not try to detach
them from each other.
•• Do not throw the filter or use it for other purposes.
Note
•• Keep the windows or doors closed while
using the product. However, if you operate
the product for a long time in a closed space,
carbon dioxide concentration may rise. So
be sure to ventilate the indoor air regularly.
•• Carbon monoxide (CO) is a harmful gas
that is mainly introduced from outside and
cannot be removed with a filter.
•• The deodorization function of the air
purifier operates by trapping the smell (gas)
in the filter. If you use the product for a
long time in a room with excessive smell,
the performance of the filter may drop
significantly. The Total Harmful Gas Care
Filter may sometimes become the source
of excessive smell if used for a long time
in a room with excessive smell.
•• If excessive smell is present in the room,
first ventilate the indoor air to remove the
smell. Then use the air purifier to remove
the remaining smell.
19
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 19
2017-09-21 �� 3:47:42
Control Panel
Start/Stop Button
Booster Speed Button
You can start or stop the operation.
It allows you to adjust the wind
strength of the clean booster.
Mode Button
•• Press and hold it for 3 seconds or
more to turn on or off the ionizer.
(See Using the Air Ionizer.)
Use it to set the operation mode.
•• Press and hold the button for 3
seconds or more to turn on/off the
Light lamp.
(See Turning on/off the Light
Lamp.)
Speed Button
Swing Button
It allows you to set the clean booster
to turn left or right.
Indicator Button
It allows you to adjust the wind
strength of the product.
You can check the concentration of
the airborne dust by its particle size.
•• Press and hold the button for 3
seconds or more to activate the
Wi-Fi registration mode (The WiFi registration mode automatically
goes off in 10 minutes). (See Smart
Functions.)
Sleep Timer Button
Use it to schedule the time to turn off
the product.
•• Press and hold it for 3 seconds or
more to lock or unlock the Control
Panel buttons. (See Locking the
Control Panel Buttons.)
20
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 20
2017-09-21 �� 3:47:43
Status Display Panel
Display of air quality
1 Overall air quality (color)
2 Dust particle size and dust
concentration (color)
3 Dust concentration or sleep timer
time
4 Smell concentration (color)
Icons
Icon
Description
It turns on when it is time to replace
the upper filter.
It turns on when it is time to replace
the lower filter.
Displays operating mode
It turns on when the Wi-Fi function
is activated.
Displays speed and booster speed
It turns on when the sleep timer
function is activated.
Speed: Displays the air purifier's
wind strength.
It turns on when the 'On/Off
Reservation' is set in the LG Smart
ThinQ application.
Booster Speed: Displays the
clean booster's wind strength.
It turns on when the control panel is
locked.
It turns on when the ionizer turns On.
21
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 21
2017-09-21 �� 3:47:43
Remote Control
Caution
•• Do not press multiple buttons at the same
time. It may cause the product to stop
operating or malfunction.
•• Do not kick or step on the remote control.
It may result in damage.
•• Do not use it where there is too much
water or moisture. It may result in fire or
electric shock.
•• Do not use it where there is fire or heat. It
may result in a fire or product deformation.
Start/Stop Button
You can start or stop the operation.
Speed Button
It allows you to adjust the wind
strength of the product.
Sleep Timer Button
Use it to schedule the time to turn off
the product.
Booster Speed Button
It allows you to adjust the wind
strength of the clean booster.
Light Button
Use it to turn on or off the Light Lamp.
Mode Button
•• Remove and store the battery in a safe
location if you don't intend to use the
remote control for a long time. It may result
in leakage of the battery liquid and lead to
a failure.
Note
•• To use the remote control, direct the signal
sending area of the remote control toward
the signal reception area of the product.
•• If you are away from the product (front) by
more than 7 m, the remote control may not
work.
•• If the remote control does not work even
after replacing the battery, contact the
nearest service center.
•• The remote control may not work properly
where there is a strong light, such as those
from a 3-wavelength fluorescent lamp or a
neon sign.
•• If you lost the remote control, you can
purchase a new one in a nearby service
center.
Use it to set the operation mode.
Swing Button
It allows you to set the clean booster
to turn left or right.
22
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 22
2017-09-21 �� 3:47:43
Getting Started
Using Smart Mode
Press the Start/Stop button to start the
operation.
It automatically controls the operation mode
and wind strength based on the overall air
quality.
Press Mode button to choose Smart mode.
•• Each time you press the button, the
operation mode changes in the following
order: Smart → Booster → Dual →
Single.
Note
•• If you operate the product for the first time,
it enters Booster mode.
•• If you stop and resume the operation, it
starts cleaning with the mode you selected
last time. Even if power is lost due to a
blackout, the product remembers the mode
you used last time.
•• Once the operation starts, the sensor
stabilizes (for approx. 30 seconds) before
the dust concentration is displayed. During
the sensor stabilization period, you will see
(ready) on the status panel.
You can specify the sensor stabilization
time in the 'Air Quality Sensor Operation
Time' option in the LG Smart ThinQ
application.
Note
•• While in Smart mode, the Speed, Boost
Speed and Swing buttons do not work.
•• Smart mode operates either the clean
booster, upper purifier or lower purifier to
adapt to the air quality.
–– 'Always On': The sensor stabilization
turns on only once at the beginning.
–– 'Only During Operation': The sensor
stabilization turns on every time you
start/stop the operation.
23
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 23
2017-09-21 �� 3:47:44
Using Booster Mode
Using Dual Mode
The clean booster cleans the air and quickly
sends it to a long distances to circulate the
indoor air.
It uses both the upper part and lower part of
the purifier simultaneously to quickly clean
the indoor air.
Press the Mode button to choose Booster
mode.
Press the Mode button to choose Dual
mode.
•• Each time you press the button, the
operation mode changes in the following
order: Smart → Booster → Dual →
Single.
•• Each time you press the button, the
operation mode changes in the following
order: Smart → Booster → Dual →
Single.
Caution
Keep your hands out of the moving part of
the clean booster.
Note
•• If you choose Booster mode, the clean
booster rises at the degree of 55 and
pushes the air forward to circulate the
indoor air.
•• For more information on how to control
the wind strength of the clean booster, see
Adjusting the Clean Booster Fan Speed.
•• To rotate the clean booster left and right,
see Rotating the Clean Booster.
24
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 24
2017-09-21 �� 3:47:45
Using Single Mode
Adjusting the Fan Speed
It cleans the indoor air using the lower part of
the purifier.
Press the Mode button to choose Single
mode.
You can adjust the wind amount of the
purifier.
•• Each time you press the button, the
operation mode changes in the following
order: Smart → Booster → Dual →
Single.
Note
The upper part of the purifier runs with gentle
wind for optimal performance.
Press the Speed button during the operation.
•• Each time you press the button, the speed
changes in the following order: Auto →
Low → Middle → High → Turbo.
Displaying Purifier Speed
If you adjust the speed, it is displayed on the
status panel. It increases by 2 grids at a time.
[Example of Purifier Speed 'Middle']
Note
•• The speed is set to Auto when you first
start the operation. Auto mode controls
the wind speed automatically according to
the contamination level of the indoor air.
•• You can control the wind speed only in the
Booster, Dual, and Single modes.
25
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 25
2017-09-21 �� 3:47:46
Adjusting the Clean
Booster Fan Speed
Rotating the Clean Booster
You can adjust the wind amount of the clean
booster.
While in Booster mode, press the Swing
button.
The clean booster rotates left and right.
While in Booster mode, press the Booster
Speed button.
•• Each time you press the button, the speed
changes in the following order: Auto →
Low → Middle → High → Turbo.
Caution
Keep your hands out of the moving part of
the clean booster.
Note
Displaying Booster Speed
If you adjust the booster fan speed, it is
displayed on the status panel. It increases by
2 grids at a time.
[Example of Booster Speed 'Middle']
•• The rotating angle of the clean booster is
35°.
•• You may use the clean booster rotation
function only in Booster mode. In the other
modes, you will hear a warning sound and
won't be able to control the function.
Note
•• If you choose Auto, the fan inside the
clean booster is adjusted according to the
speed of the purifier. For example, if you
change the speed of the purifier to 'Low',
the booster fan speed is changed to 'Low'
as well.
•• You may control the booster fan speed
only in Booster mode. In the other modes,
you will hear a warning sound and won't
be able to control the function.
26
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 26
2017-09-21 �� 3:47:48
Checking the Air Quality
You can check the cleanliness of the indoor air by looking at the Light lamp and the status panel.
Understanding the Overall Air Quality
The overall air quality is calculated based on the dust and smell (gas) concentrations and is
categorized into 6 levels including green, yellow, orange, red, pink or violet depending on the
contamination of the air.
PM density (μg/m³)
Overall Air
Quality
State
PM10
(fine dust)
Violet
Severe
421 or more
251 or more
Pink
Very Poor
351 – 420
151 – 250
PM2.5
(ultra fine dust)
PM1.0
(super ultra fine dust)
Odor Level
State
Level
-
Red
Poor
251 – 350
116 – 150
Very strong
4
Orange
Unhealthy
151 – 250
76 – 115
Strong
3
Yellow
Moderate
51 – 150
36 – 75
Normal
2
Green
Good
50 or less
35 or less
Weak
1
•• Overall air quality can be determined based on the Light lamp and the
air quality) on the status panel.
color (overall
•• The color of overall air quality is determined based on whichever is worse between the dust
concentration and smell (gas) concentration.
Checking the Air Quality Using
the Light Lamp
Six different colors are used to indicate
the overall air quality based on the dust
concentration and smell (gas) concentration.
Turning on/off the Light Lamp
You can press and hold the Mode button for
3 seconds or more to turn it on/off.
Upper Light
Lamp
Lower Light
Lamp
Note
The Light lamp turns on white for the sensor
stabilization period (30 seconds). The smell
(gas) sensor is stabilized 2 minutes after you
start the operation. During this period, the
smell (gas) concentration is not reflected in
the overall air quality.
Note
•• When the sleep timer is set, the Light lamp
turns off.
•• If you turn on the Light lamp after setting
the sleep timer, you will see the overall air
quality on the status panel as well as on
the Light lamps.
27
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 27
2017-09-21 �� 3:47:49
Checking Air Quality on the Status Panel
You may check the overall air quality, dust
concentration, and smell concentration on
the status panel.
•• Overall air quality: You can check the
color (overall air quality) on the
status panel to determine the overall air
quality.
•• Dust concentration: You can check the
dust concentration by looking at the dust
concentration value and the particle size
indicator color. It shows the worst status
among the PM 10 (fine) / PM 2.5 (ultra-fine)
/ PM 1.0 (super ultra-fine dust).
–– If the dust concentrations of all
categories are 'good', the concentration
of the 'PM 10' is displayed.
–– If it is worse than 'moderate', the color
and concentration of the dust with
the highest contamination level are
displayed. If they share the same
contamination level, the contamination
level is displayed according to the
following order: PM 1.0, PM 2.5 and
PM 10.
•• Smell concentration: You can check
the
color (smell concentration) on
the status panel to determine the smell
concentration.
[Example of the Display Showing Air
Quality]
Dust particle
size and
concentration
color
The above picture displays PM10/PM2.5/
PM1.0, meaning that the concentration of
super ultra-fine dust is higher than those of
fine dust and ultra-fine dust.
While the color of the dust particle size
is solely determined based on the dust
concentration and the color of the
(smell
concentration) is solely determined based
on the smell concentration, the color of the
(overall air quality) is determined
based on the worse cause between the dust
and smell.
If the smell is 'normal' and the PM 1.0 (super
ultra-fine dust) concentration is 100 μg/m3,
which is 'unhealthy', the overall air quality is
displayed in orange as the worst cause is the
dust. On the other hand, if the smell is 'very
strong', the overall air quality is displayed in red
because the smell becomes the worst cause.
Checking the Dust
Concentration
You can check the airborne dust
concentration by its particle size.
Press the Indicator button during the
operation.
•• Whenever you press the button, the
display changes in the following order:
PM10 → PM2.5 → PM1.0.
•• The concentration of the selected dust
particle is displayed for about 10 seconds.
Overall air quality
Smell
concentration
color
Dust concentration
28
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 28
2017-09-21 �� 3:47:50
Note
•• PM (particulate matter) density is displayed
in increments of 1 unit, from 8 to 999. PM
density values are based on the data sheet
provided by the sensor manufacturer.
•• The PM10 and PM2.5 air quality values
are based on LG Electronics standards.
–– The overall air quality level displayed
on the product may differ from the level
announced by the Central Pollution
Control Board (CPCB).
•• The PM1.0 density is displayed in the
same manner as the PM2.5 density and is
based on LG Electronics standards.
•• The PM10 and PM2.5 densities displayed
by the product could differ from the Central
Pollution Control Board (CPCB) and from
densities measured by other products or
devices.
•• The dust density displayed may change
with environmental factors such as the
presence of sofas, beds, carpets, vacuum
cleaners, humidity, smoke, bugs, pets or
cooking oils.
•• The PM densities may be affected by
changes in the outside environment such
as construction, heavy traffic or pollen.
•• The micro dust density could be higher
near outside doors, windows, vents or in
areas where outside air enters.
•• Use ONLY water to clean the sensor.
Using anything else could cause product
failure.
•• The fine dust density could be affected
by cooking or using humidifiers, sprays or
other products which generate steam or
fine particles.
–– Differences in PM density values may
be the result of different methods of
measuring or differences in the actual
PM density levels.
–– The PM density measurement was
tested using LG Electronics’ standard
test materials.
•• Using the product near a humidifier, mist
generator, air-conditioner or other device
which generates steam or micro-particles
could affect the PM densities.
•• The overall air quality level is a result of
both PM densities and the odor level. It
may differ from the PM10, PM2.5 and
PM1.0 density levels.
•• Even two products placed in the same
space could measure the PM10 density
differently due to air circulation.
•• The chemicals contained in air fresheners,
perfumes, deodorizers or cosmetics may
affect the overall air quality display.
29
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 29
2017-09-21 �� 3:47:50
Using the Air Ionizer
Setting the Sleep Timer
To generate ions to remove various bacteria
from the air.
You can set the product to stop automatically
after running for the duration you set.
Press the Booster Speed button for more
than 3 seconds while operating.
Press the Sleep Timer button during the
operation.
••
•• Each time you press the button, the Sleep
Timer changes in the following order: After
2 hours→ After 4 hours → After 8 hours →
After 12 hours → Cancel.
(Ionizer) is displayed on the status
display.
•• Once the sleep timer is set, the status
panel displays only the
sleep timer icon
except for a few other icons.
Note
•• When the operation is stopped, the ionizer
function can not be used.
•• The ionizer function is available in all
operating modes.
Note
•• For your deep sleep, the speed is set
to Low by default for a certain period of
time. After the time passes, the speed is
controlled automatically depending on the
air quality.
•• Even when the sleep timer is set, you can
still change the speed by pressing the
Speed button.
•• If you press the Sleep Timer button once
more while the sleep timer is set, you can
check the preset time and press the button
repeatedly to cancel the sleep timer.
•• The sleep timer remains on even if the
power goes off or if there is a blackout.
30
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 30
2017-09-21 �� 3:47:51
Locking the Control Panel
Buttons
You can lock the buttons on the Control
Panel to prevent the product from operating
due to unforeseen reasons, such as a child
manipulating the buttons.
Press the Sleep Timer button for at least 3
seconds during the operation.
••
(Lock) is displayed on the status panel.
Note
•• You can turn off the lock function in the
same way as turning it on.
•• The control panel can be locked even
when the product is off.
•• If you pull out the power plug in lock set
status, the lock function is cleared.
31
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 31
2017-09-21 �� 3:47:52
Smart Functions
Using the Smart ThinQ
Application
Install the "LG Smart ThinQ" application on
your smartphone to use the product more
conveniently.
Installing Smart ThinQ
Find and install ‘LG Smart ThinQ’ from
the App Store/Google Play Store on your
smartphone. For more information on how to
use 'LG Smart ThinQ’, refer to the Help in the
app.
Wi-Fi function
Smart diagnosis
When the product malfunctions or fails,
you can check the product conditions
through the smart diagnosis function and
solve issues more conveniently.
Settings
You can configure the product
management and alert settings.
Note
•• Wi-Fi only supports 2.4 GHz frequency.
•• When registering the product, make
sure that the Wi-Fi connection of the
smartphone is on.
•• Install the wireless router at a location
close to the product. The strength of
the signal may be different based on
the location and distance between the
product and the wireless router, resulting
in difference in the data transmission time
thereby.
•• The connection may not be established
depending on the network environment. If
you cannot connect to the network or there
is a problem with the network settings,
contact the network administrator or the
Internet service provider.
•• If the security protocol of the router is
set to WEP, you may fail to set up the
network. Please change it to other security
protocols (WPA2 is recommended) and
register the product again.
•• Be sure to use any alphanumeric
combination to set the wireless network
name (SSID), which appears when you
search for Wi-Fi.
•• When you search for a wireless router to
connect to the wireless network, wireless
routers other than the one you are using
may also be found.
Using other people's routers is illegal and,
if you do so, you may be subjected to legal
actions. You must connect to the wireless
router authorized to use the network.
•• The contents of this manual may vary
depending on the version of the "LG Smart
ThinQ" application, and they may be
changed without prior notice.
•• A wireless router and an Internet
connection cable are separate purchase
items required to use the app and you
need to install them separately.
•• To use the wireless network, you can
contact an Internet service provider or
install the wireless router on your own.
When you install the wireless router on
your own, please refer to the user manual
enclosed with the wireless router.
32
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 32
2017-09-21 �� 3:47:52
Wi-Fi Module Specifications
As the wireless equipment may cause radio
interference, it must not be used to provide
life-saving services.
Open Source Software License
Notice
Please visit http://opensource.lge.com to
obtain open source codes developed under
GPL, LGPL, MPL or other open source
licenses that are included in this product.
Diagnosis via Wi-Fi
1
2
3
Smart Diagnosis function
•• This only applies to the models with the
logo.
When the product malfunctions or fails, you
can check the product conditions through the
smart diagnosis function and solve issues
more conveniently by using Smart ThinQ
application.
Select the product for Smart Diagnosis
among the registered products, and
press the menu at the top right area of
the smart-phone screen.
Select Smart Diagnosis on the
smart-phone screen, and press the
Start Smart Diagnosis button.
•• You can check the results of Smart
Diagnosis in the ‘LG Smart ThinQ’
app.
In addition to source codes, you can also
download the contents of all licenses,
copyright indications and indication of no
warranty.
If you request open source codes for any
software included in this product by sending
an email to opensource@lge.com within
three years of purchasing the product, we will
send the codes on a CD-ROM with minimal
charges for the CD and shipping.
Check the product’s Wi-Fi connection
status.
If Wi-Fi Diagnosis Fails
•• If the network connection is not smooth,
Smart Diagnosis may fail. Press the Retry
button to try again.
•• If Smart Diagnosis via Wi-Fi keeps failing,
press the Audible Diagnosis button, and
follow the instructions displayed on the
smart-phone screen to perform Audible
Diagnosis.
Note
If any problems arise regarding the product
after Smart Diagnosis, you can contact the
Customer Center to find out more on the
details of the diagnosis.
33
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 33
2017-09-21 �� 3:47:53
Diagnosis Using Sound
•• This only applies to the models with the
logo.
Use this function if you need an accurate
diagnosis by an LG Electronics service
center when the product malfunctions or fails.
Use this function only to contact the service
representative, not during normal operation.
5
2
3
4
•• The microphone on your phone
should face the Smart Diagnosis
( ) logo on the back. Do not
remove the phone from the product
while data is being transmitted.
•• You need to keep the phone near
the product while the data is being
transmitted for Smart Diagnosis.
Smart Diagnosis™ can not be activated
unless the appliance is connected to power.
1
Place the phone near the product.
•• The data transfer sound may be
harsh to the ear while the smart
diagnosis data is being transmitted
but do not take the phone off the
product for accurate diagnosis
until the data transfer sound has
stopped.
Open the LG Smart ThinQ application
on the smart phone.
Press Smart Diagnosis button.
Follow the instructions on the smart
phone.
Press and hold the Indicator button
for 5 seconds or more to execute the
Smart Diagnosis function.
6
After the data transfer is complete, the
service agent will explain the result of
the smart diagnosis.
•• After the service agent explains
the diagnosis result, take the
recommended measures.
Note
•• The Smart Diagnosis function depends
on the local call quality.
•• The communication performance will
improve and you can receive better service
if you use the home phone.
•• The diagnosis data transmission may not
be smooth due to poor communication
quality, in that case, the smart diagnosis
service may not be provided properly.
34
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 34
2017-09-21 �� 3:47:53
Maintenance
Caution
•• You must stop operating the product and
unplug it before you clean and replace the
filter.
•• Do not spray water directly on the product.
•• Assemble the product in the reverse order
of disassembly after cleaning the product
and replacing the filter.
•• How to distinguish between the front
and back of the product: There is an LG
logo on the front, while 'PM 1.0 & GAS
SENSOR SYSTEM' is written on the back.
Scheduled Maintenance
Component
Cleaning
Frequency
Replacement
Frequency
Only ultra-fine
filter
Filter
If contaminated,
clean the ultrafine filter with a
vacuum cleaner
or soft brush.
The whole filter
•• Filters are sold at the nearest Service
Center or via the Consumables shop on
the LG Electronics site (www.lg.com).
•• You may also request cleaning or
replacement of the filter to the Service
Center. You will be charged a certain
fee for filter cleaning and replacement
services.
•• If there are no changes to the dust
concentration on the status panel, clean
the sensor regardless of the cleaning
frequency (2 months) of the PM 1.0
sensor. For more information on cleaning
the PM1.0 sensor, please see Cleaning
the Dust Sensor.
Alerts on the Status Panel
When you see an alert message on the
status panel, do the following:
Alert
1 year
Measures
•• Replace the upper filter.
•• Replace the lower filter.
Note
2 months
-
PM 1.0 (super
ultra-fine dust)
sensor
Note
•• The operating environment and operation
hours may affect the cleaning frequency.
We recommend that you should clean it
more often in a dusty environment.
•• If you do not clean the product according
to the cleaning frequency, you may
experience a bad odor and poor
performance.
•• Filter replacement alerts appear based
on the maximum usage time, taking into
account the operating hours of the product.
The replacement frequency is determined
by the operating hours and environment.
•• For more information on how to disable a
filter replacement alert, see Replacing the
Filter.
•• A filter is a consumable item. Therefore
you must buy a new one for replacement
when it has reached the end of its lifespan
even during the warranty period.
35
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 35
2017-09-21 �� 3:47:54
Caution
2
Wipe the exterior with soft cloth.
•• Do not disassemble the clean booster
arbitrarily.
•• If the clean booster cover comes apart,
secure it by aligning the 3 hooks with the
slots before you use the product.
•• Do not unscrew the 2 screws fixing the
clean booster grille on the back while
the product is running.
Caution
•• Do not clean the product with an alkaline
detergent.
•• Do not wipe the product surface using
sulfuric acid, hydrochloric acid or organic
solvent (thinner, kerosene etc.) or attach
a sticker on the product. Otherwise the
product surface may get damaged.
Cleaning the Exterior
1
Remove dust from the air inlet and
outlet using a vacuum cleaner.
•• Do not allow the water enter inside the
product.
Note
If you find it difficult to clean the front and
rear covers, separate them first and wash
with water. Then, dry them completely under
the shade.
36
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 36
2017-09-21 �� 3:47:56
Cleaning the Filter
Replacing the Filter
1
1
2
Separate the cover from the product.
•• For more information on how to
remove and mount the cover,
please see Removing Packing
Materials.
Remove the cover and replace the
filter.
•• For more information on how to
remove the cover and replace
the filter, please see Removing
Packing Materials.
Remove dust from the ultra-fine filter
with a vacuum cleaner or soft brush.
•• To avoid polluting the surroundings
when replacing the filter, place a
newspaper on the floor before you
remove the filter.
2
Once you have replaced the filter,
disable the filter replacement alert.
Disabling an Upper Filter
Replacement Alert
Press and hold the Speed and Indicator
buttons simultaneously for 3 seconds or
more.
Caution
•• The (Upper Filter Replacement Alert)
is disabled and the replacement alarm is
reset.
•• Do not wash the filter with water. It may
reduce the lifespan of the filter.
•• Be careful not to damage the ultra fine
filter when you use a vacuum cleaner.
37
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 37
2017-09-21 �� 3:47:58
Disabling a Lower Filter
Replacement Alert
Press and hold the Indicator and Sleep
Timer buttons simultaneously for 3
seconds or more.
•• The (Lower Filter Replacement Alert)
is disabled and the replacement alarm is
reset.
Cleaning the Dust Sensor
PM 1.0 (super ultra-fine dust) sensor
detects the fine dust as well as coarse
dust. Therefore, you need to clean its lens
regularly.
1
2
Remove the rear cover from the
product.
•• For more information on how to
remove and mount the cover,
please see Removing Packing
Materials.
Open the sensor cover.
Note
•• The filter replacement alert is disabled
automatically if 24 hours have passed
since it was displayed or if the product is
disconnected from the power source.
3
Clean the lens with the cotton swab
soaked with water and clean it again
with a dry cotton swab.
38
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 38
2017-09-21 �� 3:48:01
4
Close the sensor cover.
2
Turn off the power and unplug it from
the electrical outlet.
•• Wind the power cord around the
bottom of the product.
Note
The shape of the power plug differs
depending on the country.
Note
Do not wipe the sensor with material other
than water. It may cause a product failure.
3
Package the product to prevent
the dust or foreign substance from
entering the product. Store the
packaged product at a shaded place.
Storage
If the product is not used for a long period of
time, store it at a shaded and dry place.
1
Operate the product in Dual mode for
one hour or more on a fine day.
•• This removes the moisture and
prevents molds from building up
inside the product.
Caution
Do not store the product at a humid place
or at a place exposed to the direct sunlight.
Otherwise the product may be deformed,
malfunction or generate odor.
39
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 39
2017-09-21 �� 3:48:03
Before Calling for Service
If a failure occurs in the product, check the following before contacting the Service Center.
Symptom
Cause
Solution
The product does not
operate.
Is the power plug
unplugged from the outlet?
•• Plug it into the outlet properly.
Did dust accumulate in
the ultra fine filter?
•• Clean the ultra fine filter
properly.
Did dust accumulate
in the Total Allergen
Collection Care Filter?
•• Replace the whole filter.
Is the indoor
contamination severe?
•• Ventilate the indoor air before
you use the product.
Did dust accumulate in
the ultra fine filter?
•• Clean the ultra fine filter
properly.
Did dust accumulate
in the Total Allergen
Collection Care Filter?
•• Replace the filter.
Fan is noisy even on
the lowest speed.
The indoor air is not
purified well enough.
There is a smell, but
the Light lamp does
not change.
Are you using it in a place
that is too spacious or too
open?
•• Use a product that fits the size
of the room.
•• Avoid a well-ventilated place
such as a gate, window, etc.
Is there any obstacle nearby?
•• Remove the obstacle.
Is the product installed at
a corner?
•• Move the product and install it
again.
Is the Light lamp turned
on red or amber?
•• The color of overall air quality
is determined based on
whichever is worse between
the dust concentration and
smell (gas) concentration.
Check if the dust concentration
is worse than before.
•• The smell (gas) sensor
detects the gas that causes
contamination, so it may not
react to the food smell Indian
food such as curry and breads
etc. But the Total Harmful Gas
Care Filter does remove the
odor.
40
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 40
2017-09-21 �� 3:48:04
Symptom
The Light lamp
continues to stay
red.
The buttons on the
control panel do not
work.
The concentration
of the fine dust does
not change.
The concentration of
fine dust continues
to remain high.
The overall air
quality color does
not match the dust
concentration value.
Cause
Doesn’t the color change
even if it is moved to a
clean room?
Solution
•• If the amount of the smell is
more than the capacity of the
product, the display may not
change.
•• Clean the sensor area.
•• Remove the power plug from
the outlet and reconnect it one
minute later.
Did you use a spray near
the product?
•• Do not use a spray near the
product.
Is the (Lock) turned on
on the status panel?
•• Press and hold the Sleep
Timer button for 3 sec. or
longer to disable the lock
function.
Is there a foreign
substance on the sensor?
•• Clean the PM 1.0 (super ultrafine dust) sensor.
Is the product used in a
closed space?
•• In a closed space, the
cleanliness level may continue
to stay the same without
change.
Does the air continue to
flow in from the outside
to the location where the
product is installed?
•• In an environment where
outside air is supplied
continuously, the
concentration may continue to
remain high.
Does the color of the
overall air quality match
the color that indicates
the smell concentration?
•• The overall air quality is
displayed by evaluating the
smell and dust concentration
comprehensively.
•• Even if the dust concentration
is low, if the odor is strong,
the overall air quality color
may not match the dust
concentration value.
41
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 41
2017-09-21 �� 3:48:04
Symptom
The overall air quality
is different from that
of the Ministry of
Environment guide.
A strange smell
comes out from the
air outlet as well as
the filter.
Cause
Solution
Is the guide from the
Ministry of Environment
different from the product
dust concentration?
•• The Ministry of Environment
guide shows the average
value over a certain period of
time, but the overall air quality
displayed on the product is
measured in real time. So they
may be different from each
other.
Did you purchase the
product lately?
•• The odor of activated
charcoal is not harmful. This
is similar to the smell you may
experience in a brand new
car. We assure it will go way
1-2 weeks after its first use.
Is the product used at a
place with a lot of smoke
or smell?
•• In a place with a lot of smoke
or smell, the air cleaning
function may deteriorate.
Ventilate the room first and
then use the product.
Does the filter have a bad
smell?
•• Replace the filter. The filter
replacement frequency may
differ depending on the usage
environment.
Is the product installed in
an environment where a
lot of odor occurs?
The clean booster is
not working.
Is the operation mode
set to the Clean Booster
mode?
A noise is generated
when I start or stop
the clean booster.
-
•• If you use the product for a
long period of time while you
cook or broil fish/meat, the
filter lifespan may be rapidly
decreased.
•• If possible, open the window
for ventilation while cooking,
and use the product to
remove the smell left after the
ventilation.
•• The booster fan speed and
booster fan rotation functions
work only in the Clean Booster
mode.
•• It means that the clean
booster is trying to look for the
correct location.
42
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 42
2017-09-21 �� 3:48:04
Symptom
I can't connect to
the product in the
LG Smart ThinQ
app.
I can't register the
product in the LG
Smart ThinQ app.
The dust
concentration levels
are different between
the product and the
LG Smart ThinQ app.
Cause
Is the power plug
unplugged from the
outlet?
Is the wireless router
connected with the
product not working?
Solution
•• Plug in the power cord of the
product.
•• Power off the wireless router
and on again.
•• Check if there is an Internet
connection problem with the
router.
Is the product too far
away from the wireless
router?
•• Move the wireless router near
the product.
Is your wireless router
working properly?
•• Some carriers provide routers
that are available to their
members only. If you have an
outdated model, contact your
carrier to have it replaced with
a newer one.
Are you looking at the
same dust particle?
•• Make sure that the levels
of the super ultra-fine/ultrafine/fine dust are displayed
consistently between the LG
Smart ThinQ app and your
product.
•• The difference in the values
could be caused by the
difference in update time
between the LG Smart ThinQ
app and the product.
43
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 43
2017-09-21 �� 3:48:04
Product Specifications
Height
Depth
Width
The external appearance and dimensions of the product are subject to change without prior
notice.
Model
AS95GD Series
Power
AC 220–240 V 50Hz
Exterior dimensions
(Width X Height X Depth)
When the clean booster is not running:
373 mm x 1073 mm x 373 mm
When the clean booster is running:
373 mm x 1310 mm x 373 mm
44
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 44
2017-09-21 �� 3:48:05
Warranty
45
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 45
2017-09-21 �� 3:48:05
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 46
2017-09-21 �� 3:48:06
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 47
2017-09-21 �� 3:48:06
Montblanc_D_Air_Cleaner_28PY_UG_INDIA_ENG.indd 48
2017-09-21 �� 3:48:06
Download PDF