Please read this manual carefully before operating the unit. MTNL / BSNL (Toll Free) Prefix STD Code Room Air Conditioner Owner’s Manual TABLE OF CONTENTS FOR YOUR RECORDS Safety precautions Safety Precautions ..................................................3 Write the model and serial numbers here: Model # Operating instructions Caution while operating Air Conditioner ..................4 About the Controls on the Air Conditioner ...............8 Care and Maintenance ..........................................13 Serial # You can find them on a label on the side of each unit. Dealer's Name Date Purchased n Staple your receipt to this page in the event you need it to prove date of purchase or for warranty issues. Installation Instructions Installation Instructions............................................14 READ THIS MANUAL Troubleshooting tips Before You Call for Service.....................................16 10 Easy steps to find AC Tonnage ........................17 Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all. PRECAUTION • Contact the authorized service technician for repair or maintenance of this unit. • Please install your air-conditioner by company authorised service franchisee / authorised service and sales dealer. • The air conditioner is not intended for use by young children or invalids without supervision. • Young children should be supervised to ensure that they do not play with the air conditioner. • When the power cord is to be replaced, replacement work shall be performed by authorized personnel only, using only genuine replacement parts. We recommend usage of voltage stabilizer with high / low voltage cut off in areas having voltage fluctuations. -2- AC TONNAGE STABILIZER KVA (3-STEP STABILIZER) 0.75 1.0 1.5 2.0 3 3 4 5 Safety Precautions To prevent injury to the user or other people and property damage , the following instructions must be followed. n Incorrect operation due to ignoring instruction will cause harm or damage. The serIousness is classified by the following indications. WARNING This symbol indicates the possibility of death or serious injury . CAUTION This symbol indicates the possibility of injur y or damage to proper ties only. n Meanings of symbols used in this manual are as shown below . Be sure not to do. Be sure to follow the instruction. WARNING n Installation Don’t use a power cord, a plug or a loose socket which is damaged. • Otherwise, it may cause a fire or electrical shock. Always plug into a grounded outlet. • Otherwise, it may cause a fire or electrical shock. Do not modify or extend the power cord length. • It will cause electr ic shock or fire due to heat generation. Do not disassemble or modify products. Be caution when unpacking and installing. Do not use the power cord near flammable gas or combustibles such as gasoline, benzene, thinner, etc. • It may cause failure and • Sharp edges may cause injury. • It may cause explosion or fire. electric shock. -3- CAUTION WHILE OPERA TING AC n Operation Do not place heavy object on the power cord and take care so that the cord should not be pressed. Do not share the outlet with other appliances. • There is danger of fire or electr ic shock. • It will cause electr ic shock or fire due to heat generation. Do not place the power cord near a heater. • It may cause fire and electr ic shock. Do not allow water to run into electric parts. • It will cause failure of machine or electric shock. Unplug the unit if strang e sounds, odors, or smoke come from it. Do not open the suction inlet grill of the product during operation. • Otherwise it may cause fire and electric shock accident. • Otherwise, it may electrical shock and failure. Ventilate the room well when using this appliance together with a stove, etc. Turn off the power and breaker firstly when cleansing the unit. • An oxygen shortage may occur. • Since the fan rotates at high speed during operation, it may cause injury. -4- Take the power plug out if necessary, holding the head of the plug and do not touc h it with wet hands. • Otherwise, it may cause a fire or electrical shock. Use a soft cloth to clean. Do not use wax, thinner, or a strong detergent. • The appearance of the air conditioner may deteriorate, change color, or develop surface flaws. If water enters the product, turn off the the power switch of the main body of appliance. Contact service center after taking the power-plug out from the socket. Turn off the main power switch when not using it f or a long time. • Prevent accidental startup and the possibility of injury. Do not operate or stop the unit by inserting or pulling out the power plug. • It will cause electr ic shock or fire due to heat generation. Hold the plug by the head when taking it out. • It may cause electric shock and damage. Do not damage or use an unspecified power cord. • It will cause electr ic shock or fire. When gas leaks, open the window for ventilation before operating the unit. • Otherwise, it may cause explosion, and a fire. CAUTION -5- Do not operate with wet hands or in damp environment. • It will cause electr ic shock. Never touch the metal parts of the unit when removing the filter. • They are sharp and may cause injury. n Operation Do not put a pet or house plant where it will be exposed to direct air flow. • It may cause injury. Do not step on the indoor/outdoor unit and do not put anything on it. • It may cause an injur y through dropping of the unit or f alling down. Be cautious not to touch the sharp edges when installing. • It may cause injury. Do not block the inlet or outlet of air flow. Use a soft cloth to clean. Do not use wax, thinner, or a strong detergent. • It may cause product failure. • The appearance of the air conditioner may deteriorate, change color, or develop surface flaws. Always insert the filter securely. Clean it every two weeks. • Operation without filters will cause failure. Avoid excessive cooling and perform ventilation sometimes. • Otherwise, it may do harm to your health. -6- Do not drink water drained from air conditioner. • It contains containments and will make you sick. Do not insert the hands or bars through the air inlet or outlet during operation. • Otherwise, it may cause personal injury. Before Operation Preparing for Operation 1. 2. 3. 4. 5. 6. Contact an installation specialist for installation. Plug in the power plug properly. Use a dedicated circuit. Do not use an extension cord. Do not start/stop operation by plugging/unplugging the power cord. If the cord/plug is damaged, replace it with only an authorized replacement part. Usage 1. Being exposed to direct airflow for an extended period of time could be hazardous to your health. Do not expose occupants, pets, or plants to direct airflow for extended periods of time. 2. Due to the possibility of o xygen deficiency, ventilate the room when used together with stoves or other heating devices. 3. Do not use this air conditioner f or non-specified special pur poses (e.g. preserving precision devices, food, pets, plants, and art objects). Such usage could damage the items. Cleaning and Maintenance 1. Do not touch the metal parts of the unit when removing the filter. InjurIes can occur when handling shar p metal edges. 2. Do not use water to clean inside the air conditioner . Exposure to water can destroy the insulation, leading to possible electric shock 3. When cleaning the unit, first mak e sure that the power and breaker are turned off. The fan rotates at a very high speed during operation. There is a possibility of injury if the unit’s power is accidently triggered on, while cleaning inner parts of the unit. Service For repair and maintenance, contact your authorized service dealer How to Insert the Batteries 1 Remove the cover from the back of the remote Do not use rechargeable controller. batteries, such batteries differ Slide the cover according to the arrow direction. from standard dry cells in shape, dimensions, and performance. 2 Insert the two batteries. Be sure that the (+) and (-) directions are correct. Remove the batteries from the Be sure that both batteries are new. 3 Re-attach the cover. Slide it back into the position. Remote controller if the air conditioner is not going to be used for an extended length of Time. -7- About the Controls on the air conditioner TEMPERATURE Operation Thermostat OPERATION AUTO SWING Auto Swing 5 Off Off 4 On Med Fan High Cool Low Fan Med Cool Off Coolest Wait for 3 minutes before restart 8 1 Cool Low Cool On Low Fan 9 Coolest Wait for 3 minutes before restart Cooling Model (Fig.1) High Cool Med Fan 7 3 2 Cool Off 6 Med Cool Low Cool Cooling Model (Fig.2) Cooling Model (Fig.3) OFF: Stop all operation. FAN: Circulates filtered air. LOW COOL: Switches on the compressor and air cooling operation at low fan speed. MEDIUM COOL: Switches on the Compressor and air cooling operation at medium fan speed. HIGH COOL: Switches on the compressor and air cooling operation at high fan speed. LOW FAN: Circulates filtered at low speed. MED FAN: Circulates filtered air at medium speed. NOTE: If you move the switch from a cool setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a cool setting. the highest number available on your Thermostat/temperarure knob(position 6~9 in fig.2) For Quieter & Nighttime Cooling Select Low Cool with the OPERATION knob at the midpoint of Thermostat / Temperature knob (position 1~4 in fig.2) COOLING DESCRIPTIONS For Normal Cooling- Select High Cool or Med Cool with the OPERATION knob at the midpoint of THERMOSTAT/ TEMPERATURE knob(as mentioned in Fig.1,fig.2 & fig.3) For Maximum Cooling- Select High Cool with the OPERATION knob at THERMOSTAT (TEMPERATURE) The THERMOSTAT/TEMPERATURE is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the same level of comfort. When you turn the knob to a higher number (the right side) and the indoor air will become cooler. The temperature is selected by turning the Thermostat/temperature knob to the desired position. The 5 or 6 position (the middle position of arc) is a normal setting for average conditions. -8- Your Panel may look like any of below mentioned panels. 2 3 22 Timer Cool Dry On 7 POWER POWER 1 1 Energy Saver FAN SPEED AUTO SWING V Mode Fan Type 1 REMOTE CONTROLLER V Fan Speed DOWN 1 ON/OFF FAN SPEED FAN SPEED 6 5 4 4 TIMER COOLING/FAN TIMER COOLING/FAN Fan Cool UP 5 5 Temp 4 DOWN UP 22 Timer Type 2 3 7 3 2 2 ENERGY SAVERAUTO SWING ENERGY SAVERAUTO SWING 2b( ) 6 2(b ) 6 V 1 V Temp Power 5 7 POWER Type 3 TEMP A ir Pu ri f i e r FAN Po w e r Mode ( e ) 1 ON Timer FAN SPEED AUTO SWING ON/OFF 4 6 1 V ENERGY SAVER 2 3 COOL Type 4 V Sl e e p M o de T i me r A ut o Sw in g 3 Temp TEMP 5 5 5 FAN SPEED 4 4 4 4 9 88 1 5 Fan Sp eed Fa n Sp e e d 7 TEMP Pow e r 8 5 V ENERGY SAVER 1 1 5 V 88 DRY Temp COOL 2 9 6 3 3 MODE 2 AUTO SWING 6 2 Sl eep M o de Tim er Aut o Sw ing 2 2(b) 6 6 FAN ON/OFF 1 Ai r Pu r if ie r Po w e r DESIRED FUZZY DRY JET ENERGY SAVER 88 88 INDOOR 1 CLEAN FILTER AIR FILTER DESIRED MODE 2 4 FAN TEMP AUTO SWING TIMER POWER MODE FAN F an V Sp e ed TIMER 2 Sl e e p 7 3 5 1 8 3 5 M ode 3 1 9 Auto Sw in g 2 Sl e e p 6 T im e r 7 2(b ) -9- M od e 3 6 Ti m e r Type 6 ON OFF SET CANCEL 4 POWER 9 6 Fa n Sp ee d 4 TEMP Air Purifier 1 5 5 V 2 4 Po w e r 8 V Type 5 INDOOR CLEAN FILTER AIR FILTER V 88 88 FUZZY DRY JET ENERGY SAVER Au t o Sw i n g PLASMA Controls Precaution: The Remote Control unit will not function properly if strong light strikes the sensor window of the air conditioner or if there are obstacles between the Remote Control unit and the air conditioner. 1 POWER // (ON/OFF) BUTTON Operation starts, when this button is pressed and stops when you press the button again. 2 OPERATION MODE SELECTION BUTTON Select (A)Cool (B)Energy Saver (C)Fan & (D)Dehumidification (dry) with this button. (A) Cool Mode: Switches on compressor & circulates cool air. (B) Energy Saver Mode : Switches ON compressor & circulates cool air , Switch OFF compressor & fan after attaining set temperature .After 3 Mins, fan switches ON and cycle repeats. (C) Fan Mode : Circulates room air without cooling(Compressor will be in switched off mode) (D) Dry Mode : Unit will run at low fan speed with compressor ON. When compressor Is OFF, fan will be OFF . 3 ON/OFF TIMER Set the time of on/off operation. The timer can be set by the one hour for a maximum of 12 hours. In the first 30 minutes set temperature increases by 1°C and in the next 30 minutes temperature increases by another 1°C, this temperature then remains till the timer function is deactivated. 4 FAN SPEED SELECTOR Select the fan speed in Three steps Low (F1) / Med. (F2) / High (F3) 5 ROOM TEMPERATURE SETTING BUTTON Control the room temperature within a range of 16°C to 30°C. 6 AUTO SWING The vertical louver swings horizontally by the automatic system and stops when you press the button again. 7 SIGNAL RECEIVER 8 AIR PURIFIER (For Plasma Model) Used to start or stop plasma purification system. Clean filter indication will be 'ON' on panel, when filter cleaning is required. 9 SLEEP BUTTON Sleep function can be set by one hour for a maximum of 7 hours. In the first 30 minutes set temperature increases by 1°C and in the next 30 minutes temperature increases by another 1°C, this temperature then remains till the timer function is deactivated. This is how the sleep function behaves. The fan speed will change to low speed(F1). Operation modes may vary in select models. Fan speed in two steps Low (F1) / High (F2) in select models. AUTO RESTART In failure of electric power the unit runs as previous setting operation when power returns. NOTE: ‘SLEEP’ and ‘TIMER’ function cannot operate at same time. -10- REMOTE CONTROLLER Type 1 Type 2 POWER (e) Turbo HIGH COOL Saver Silent High Fan Low Fan Comfort 1 27°C LOW COOL 24°C HIGH FAN 21°C TEMP 3 Cool Auto Swing Super Cool Mode Temp 2 3 1 4 LOW FAN 18°C Auto Swing 4 FAN SPEED 5 Mode Temp ON/OFF MODE 2 2 3 1 AUTO SWING 4 Controls Precaution: The Remote Control unit will not function properly if strong light strikes the sensor window of the air conditioner or if there are obstacles between the Remote Control unit and the air conditioner. 1 POWER BUTTON Operation starts, when this button is pressed and stops when you press the button again. 2 MODE Select (a) Turbo (b) Silent (c) High Fan & (d) Low Fan with this button. (a) Turbo / High Cool : Switches on compressor and air cooling operation at high fan speed. (b) Silent / Low Cool : Switches on compressor and air cooling operation at low fan speed. (c) High Fan : Circulates filtered air at high speed. (d) Low Fan : Circulates filtered air at low speed. It is recommended to select 'Silent / Low Cool' for Normal Cooling Operation and select 'Turbo / High Cool' for maximum cooling requirement. 3 TEMP Controls Room temp. from 18°C to 27°C with step of 3°C. a) Super Cool / 18°C : 18°C Temperature Setting. b) Cool / 21°C : 21°C Temperature Setting. c) Comfort / 24°C : 24°C Temperature Setting. d) (e) Saver / 27°C : 27°C Temperature Setting. 4 AUTO SWING The vertical louver swings horizontally by the automatic system and stops when you press the button again. 5 FAN SPEED Select fan speed in two steps - High/Low. -11- Additional controls and important information. Vent Control The vent control is located above the control knobs. When set at CLOSE, only the air inside the room will be circulated and conditioned. When set at OPEN, some inside air is exhausted outside. CLOSE VENT OPEN To open the vent, pull the lever toward you. To close it, push it in. Air Direction The direction of air can be controlled horizontally or vertically by using the horizontal louver or vertical louver. Horizontal Air-Direction The horizontal air direction is adjusted by setting the AUTO SWING switch to the ON position. Vertical Air-Direction Fingertip pressure on the bank of horizontal louvers adjusts the air direction up or down Parts Information Learning parts name prior to installation will help you understanding the installation procedure. 1 1. CABINET 2 3 4 5 6 15 7 8 9 10 11 12 13 14 9. CONTROL BOARD 2. FRONT GRILLE 6. VERTICAL AIR DEFLECTOR (HORIZONTAL LOUVER) 10. POWER CORD 3. AIR FILTER 7. EVAPORATOR 11. COMPRESSOR 4. AIR INTAKE(INLET GRILLE) 8. HORIZONTAL AIR DEFLECTOR (VERTICAL LOUVER) 5. AIR DISCHARGE 12. BASE PAN 13. BRACE 14. CONDENSER 15. PLASMA FILTER ASSY. -12- Care and Maintenance Grille and Case To clean, use water and a mild detergent. Do not use bleach or abrasives. Turn the air conditioner off and remove the plug from the wall outlet before cleaning. Air Filter Ensure the power is of f before open the front Grill. The air filter behind the front grille should be checked and cleaned at least once every 2 weeks or more often if necessary. The grille is designed to clean the filter downward. To remove: 1 Open the inlet grille upward by pulling out the bottom of the inlet grille. (Refer Fig. 1) (Fig. 1) (Fig. 2) 2 Using the tab, pull up slightly on the filter to release it and pull it down (Fig. 1). Slide out five filter from grill (fig. 2). 3 Clean the filter with warm, soapy water below 40°C (104°/F). 4 Rinse and gently shake the water from the filter and let it dry before replacing it. CAUTION: DO NOT operate the air conditioner without a filter because dirt and lint will clog it and reduce performance. Drainage 1 In humid weather, excess water may cause the BASE PAN to overflow. To drain the water, remove the DRAIN CAP 2 To remove the condensed water, you can install the drain pan as below. 1. Take the drain pan which is located in the air discharge. 2. Install the drain pan to the right corner of the cabinet with 4 screws. 3. Connect the drain hose to the outlet located at the bottom of the drain pan. You can purchase the drain hose or tubing locally to satisfy your particular needs. (Drain hose is not supplied). BASE PAN BASE PAN DRAIN CAP DRAIN CAP CABINET DRAIN PAN SCREW DRAIN HOSE Important Long-off period maintenance (Optional) 1)If the air conditioner is not going to be used for a long period, run the Air-conditioner with the setting in FAN Mode only and the fan speed on "HIGH" for about half an hour, to dry the whole Air-conditioner. 2)After a long off period when you are going to use the air conditioner again, repeat above point no. 1. Caution There will possibly be foul smell when the machine is started after a long time (1 week). This is due to various odours emitted by smoke, foodstuff, cosmetics and others, which syicks to the Air Filter and Evaporator coil. Hence, clean the Air Filter and the Evaporator before you start the machine after long time to avoid foul smell. -13- Installation Instructions Select the Best Location A To prevent vibration and noise, make sure the unit is installed securely and firmly. B C Install the unit where the sunlight does not shine directly on the unit. D There should be no obstacle, such as a fence or wall, within 50cm from the back of the cabinet because it will prevent heat radiation of the condenser. Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner. Install the unit a little obliquely outward not to leak the condensed water into the room (about 10 ~ 15mm or 1/4 bubble with level). CAUTION: All side louvers of the cabinet must remain exposed to the outside of the structure. Top View Side View Wall Ceiling Over 100 mm Over 110 mm Over 1000 mm Outdoor Indoor Over 200 mm 10mm AC Top Room AC Over 200 mm Position A Over 1200 mm Wall Wall Wall Indoor Floor Front View Side View Window Width "A" Unit Width 'A' Wooden frame 45~50mm 15mm About 45mm Window Height "B" Room AC Unit Height 'B' Horizontal Line -5 ~ +5mm 8~10mm 25mm About 400~500mm Wall CATEGORY 9000 Btu/h 12000 Btu/h 18000 Btu/h 22000 Btu/h A 470 600 660 660 B 355 380 428 428 Remove the Air Conditioner From the Case A Remove the 2 shipping screws from the back of the case. B Remove the 2 screws on each side of the case. Keep these for later use. C Shipping screws -14- Slide the air conditioner from the case by gripping the base pan handle and pulling forward while bracing the case. Installation Instructions Install the Air Conditioner in the Case A E Slide the air conditioner into the case. Reinstall the screws removed earlier on each side of the case. Attach the front grille to the case by inserting the tabs on the grille into the slots on the front of the case. Push the grille in until it snaps into place. Deo-filter* Screw Power Cord Screw CAUTION: The power cord must be connected to an independent circuit. The green wire must be grounded. B Stuff the foam between the unit and the wall to prevent air and insects from getting into the room. When you detach the front grille from the case, push the grille to your rightside and pull it toward you. The Foam F C Fix Holder lock with base pan & cabinet with screw to prevent machine from sliding out of cabinet from back grill side (Anti theft locking) Lift the Inlet grill and secure the front grill with a screw Lower the inlet grill into place. The maximum lift angle should not be more than 75° Max opening angle 75 degree** D * Deo-filter available in select Models. Remove Deodorizing filter carefully from the grill, shake clean it by hand & keep it in sunlight for one hour to activate it again; once it is choked. Before installing the front grille, pull out the vent control lever located above the unit control knobs, as shown. ** Grill lifting features available in selected models G -15- To fix the grill with cabinet, screw it from both sides Before you call for service... Normal Operation You may hear the thermostat click when the compressor cycles on and off. Water will collect in the base pan during high humidity or on rainy days. The water may overflow and drip from the outdoor side of the unit. The fan may run even when the compressor does not. Hissing Noise- Sound of liquid refrigerant passing through the system. Abnormal Operation Problem What To Do Possible Causes The air conditioner is unplugged. Make sure the air conditioner plug is pushed completely into the outlet. The fuse is blown/circuit breaker is tripped. Check the house fuse/circuit breaker box and replace the fuse or reset the breaker. Power failure. If power failure occurs, turn the OPERATION control to OFF( O ) . When power is restored, wait 3 minutes to restart the air conditioner to prevent tripping of the compressor overload. Airflow is restricted. Make sure there are no curtains, blinds, or furniture blocking the front of the air conditioner. THERMOSTAT control set too warm. Turn the THERMOSTAT knob clockwise to a cooler setting. The air filter is dirty. Clean the filter at least every 2 weeks. See the operating instructions section. The room may have been hot. When the air conditioner is first turned on you need to allow time for the room to cool down. Cold air is escaping. Check for open furnace floor registers and cold air returns. Set the air conditioner's vent to the closed position. Cooling coils have iced up. See Air Conditioner Freezing Up below. Air conditioner freezing up Ice blocks the air flow and stops the air conditioner from cooling the room. Set the OPERATION control at fan or HIGH cool with the THERMOSTAT at the warmer position or the temperature at more than 23°C. AC Operation is Noisy Glass pane vibrating. Glass are to be penned May be sound of condensate water. It is normal (Generally highing only) (To avoid the noise, remove draing side knob & insert drain pipe for proper drainge) Installation levelling not not proper. Get it levelled properly. Compressor not starting due to 3 minute delay internally. This is normal. If you restart the air conditioner within 3 minutes after turning it off a protective device will work to shut it off for 3 minutes. Air conditioner does not start Air conditioner does not cool as it should Unit does not Cool upon restart -16- 10 Easy Steps to find out your AC tonnage Dear Customer, Please follow Below mentioned 10 easy steps to find out the AC tonnage required for your room. Step 1 Parameter Room Volume (Cubic feet) upto 1000 1001 ~ 2000 2001 ~ 3000 3001 ~ 4000 Score Step 2 3 4 5 6 Window Area exposed to sun (in sq. ft.) - (West facing) 2 upto 10 11 ~ 20 21 ~ 30 1 2 3 7 0 1 2 3 8 Window Area exposed to sun (in sq. ft.) - (other directions) 3 4 5 upto 10 11 ~ 20 21 ~ 35 36 ~ 50 Wall Area exposed to sun (in sq. ft.) - (West facing) 100 150 200 300 Wall Area exposed to sun (in sq. ft.) - (other directions) 100 150 300 500 Score 1~5 6~10 11~17 18~25 1 2 3 4 9 0 1 2 3 10 Parameter Walls area - not exposed to sun (in sq. ft.) 100 300 600 1000 No. of persons occupying room 2 4 6 8 Ceiling area exposed to sun (in sq. ft.) 200 300 400 Ceiling area if not exposed to sun (in sq. ft.) 200 300 400 Total Appliance Load (tube light-40w / Computer75w, CTV - 75 etc.) 100W 250W 500W Score 0 1 2 3 1 2 3 4 1 2 3 0 1 2 2 3 4 AC recommended 0.75Tr 1.0Tr 1.5Tr 2.0Tr Score Table Example : For Room size 15 feet(L) x 12 feet(B) x 10 feet(H) with one window 4 feet x 3 feet exposed to sun (west) & one wall exposed to sun (east).The room is on First floor with ceiling not exposed to sun. The no. of persons occupying the room is 4 nos. The appliance load is – 2 tube lights, 1 Computer & 1 TV. Calculate the AC tonnage required. As per steps given above : room volume : 15*12*10 = 1800 cu. Ft. , window area = 4*3=12 sq.ft., Wall area (east) = 15*10=150 Step1 = 3 Step2 = 2 Step3 = 0 Step4 = 0 Step5 = 1 Step6 = 2 Step7 = 2 Step8 = 0 Step9 = 1 Step10= 3 Total score = 14 -17- 1.5T Window AC (From Score table) BRANCH BRANCH OFFICE ADDRESS Ahmedabad LGEIL, 233-234, Platinum Plaza, Judges Bunglow Road, Bodakdev Road, Ahmedabad - 51, Tel : 079 - 40040012-17 Asansol LGEIL, Block-E, Ist Floor, P C Chattarjee Market,Rambandhu Tala, GT Road (E) Asansol-713303, Tel : 0341 -3292009,3292010,3092009,3092010 Aurangabad LGEIL, 302 CIDCO No 3, Opp Hotel Ramgiri, Jalna Road, Aurangabad - 431003, Tel : 0240 - 5625705,2474055,3295436,3295437,3295438,3095438 Bangalore LGEIL, 93,TKN Mansion, Ground Flr, KH Road, Banglore-560027, Tel : 080 - 41145145,41144750,41144751,30910754, 30910753 Bhopal 13 A Vignes Warehousing Corporation, Sector-G, Govindpura Industrial Area J K Road Bhopal Tel : 0755 - 4262847,4260717,4229861,4262848,3092938,3959804 Bhubaneshwar LGEIL, Plot No.02,1st Flr., Bapuji Nagar, Bhubaneshwar- 751009, Tel : 0674 - 2531430,2534280,3966525,3966526 Calcutta LGEIL, 1,Ho-Chi-Min-Sarani, 6th Floor, Metro Towers, Calcutta-700071, Tel : 033 - 22883250/53/54/51,30946125 Chandigarh LGEIL, Plot No.177-G, Ind. Area, Phase-1,Chandigarh.-160002, Tel : 0172 - 5087389/90,3959595,3959596 Chennai LGEIL, AA11,2nd Avenue,Fatima Tower, Anna Nagar West, Chennai-600040, Tel : 044 - 65510500~04,26203506,30924478,30924479 Cochin LGEIL, 40/1270, Vasudeva Buildings, T.D.Road ,Ernakulam Cochin-682011, Tel : 0484 -2369743,2370744,4027444,4027555 Coimbatore LGEIL, 250a, Sanganur Main Road, Kannappa Nagar, Coimbatore-641027, Tel : 0422 - 2332197,2332195,3094613,3094573 Delhi(S & E ) LGEIL, A-27, Mohan Co-operative,Industrial Estate,New Delhi Delhi(N & W) LGEIL,3RD Floor, M.N Mall, Near M2K (Rohini), Sector -3, Rohini, New Delhi-85, Tel : 011 - 9873002340,9873002339,42091400 Tel : 011 -26991412/13,30989665,30989279,30989280,30989366,30989367,30989283,30989278,30989321 Dehradun LGEIL, M - 22, Mobbewala, Tata Commercial Compound, Dehradun Saharanpur Road, Dehradun, Tel : 0135 - 2644213/283,3293412,3293411 Goa LGEIL, Plot No-D-3&D-4,Rego Baug, Alto Santacruz, Bambolim, Goa-403, Tel : 0832 - 3294955,3294956,3294759 Gurgaon LGEIL, II nd Flr, A Block, Centre Point Bldg, Sushant Lok , Gurgaon, Tel : 0124 - 4047461- 62 - 633950019,3099959 Ghaziabad LGEIL, J-10, RDC Rajnagar Ghaziabad, Tel : 0120 - 9811354152,53/64/65,9811354266,3943465,3943467 Guwahati LGEIL, Shantineer Bhawan, C K Aggarwal Path, Chenikurthi, Guwahati-781003, Tel : 0361 - 2663895,2666958,2665983,2664993,2665984 Hyderabad LGEIL, K/1/1,IDA, Uppal, Hyderabad -500039, Tel : 040 - 27207504/05/06,30921140 Hubli LGEIL,603/1B, Ravi Nagar Road, Behind Renuka Petrol Pump, Gokul Road, Hubli-580030, Tel : 0836 - 2337251,52,3090749,3090651 Indore LGEIL, 3rdflr.,304 Bansi Trade Centre,581/1 M.G.Road,Indore-452003, Tel : 0731 -4065523~24,3956060,3956065 Jammu LGEIL, Plot No.-52,Transport Nagar, Narwal, Jammu, Tel : 0191 -2477420,2477419,2474396,2474384,2474574(103) Jodhpur LGEIL, 22(1-A), RIICO Heavy Industrial Area, Jodhpur - 342003, Tel : 0291 -2742403,2742384,3093489 Jalandhar LGEIL, Opp Jassi Market, Village Khajurla,Near TVS Godown, G T Road, Jallandhar, Tel : 0181 -502667/68 Jaipur LGEIL, B-71,Sahakar Marg, Lal Kothi Scheme,Jaipur-302015, Tel : 0141 -2741553,2742639,5105392,5113028 Kundli LGEIL, Sunshine Enterprises, Sunder Cold Storage, Gt Karnal Road, Kundli-Sonipat, Tel : 0130 -2219201,2219202,03 Kozhikode LGEIL, 11 / 434, Eranhikkal Bldgs, Cherooty Road, Kozhikhode- 673001 Kerala, Tel : 0495 -2366755,2366756,2366678,3255568 Lucknow LGEIL, B- 537,Hari Kunj, Keshav Nagar, Sitapur Road, Lukhnow -226020, Tel : 0522 -2757538/39/59,2759121,3951507/8/9 Ludhiana LGEIL, Village Jhande,Near Badowal Railway Station, Opp ferozpur Road, Ludhiana., Tel : 0161 - 2804412 - 21 Mumbai LGEIL, Unit No.3, L-Wing, 2nd Flr., Tax Center, Behind HDFC Bank, Off Saki Vihar Road, Chandiwali, Andheri(E), Mumbai-400072 Tel : 022 -28472410-16,28472417,39522108,39516172 Nagpur LGEIL, 5a,Road No.13, Behind Msrtc Workshop, MIDC Hinga, Nagpur-440016, Tel : 07104 -235120,235122,234401 Patna LGEIL, Sumitra Sadan, IInd Flr,West Boring Road Crossing Patna- 800001, Tel : 0612 -2204845,3298714,3299156,3298714 Pune LGEIL, 105/106, Premium Point, IIIrd Flr,Shivaji Marg.Pune -411005, Tel : 020 -56030100/732/33/34/35,30922960,30967366,30915833 Raipur LGEIL, Nathani Compound, Shyam Nagar, Katora Talab, Raipur(C.G), Tel : 0771 -4037470,4053171,4048745,3259708,3959707 Ranchi LGEIL, 402, Commerce Tower, Opp. Gel Church Complex, Main Road, Ranchi, Tel : 0651 -3290426,2331815,3090426 Surat LGEIL1001-1004, Ascon Plaza, IInd Flr, Anand Mahal Road, Behind Bhulka Bhavan School, Adajan, Surat-395009, Tel : 0261 -2730982/83/84,3954419 Thane LGEIL, Gall No. 6-9, S-2 Golden Park Complex, Hardas Nagar,LBS Marg, Panchpakhadi Thane (West)-400602, Tel : 02522 -25472633/2637/2602 Varanasi LGEIL,Pama Complex ,DLW,Lahartara Road, Shivdaspur,Manduadih, Varanasi UP, Tel : 0542 -2373432/37/36,3091774 Vijaywada LGEIL, 1st Floor, Yalamanchili Complex, Ring Road, Near Executive Club, Vijaywada - 520008, Tel : 0866 -2450128/129,3094526\3094528 Warangal LGEIL, House No. -1-8-598/1, First Floor, Beside HDFC Bank, Nakkalgutta, Hanamakonda Warangal-506001, Tel : 0870 -2551453 -18- LG Electronics India Pvt. Ltd. Registered Office: Plot No. 51, Surajpur Kasna Road, Greater Noida - 201 306 (U.P.) INDIA Tel: 0120-2560900 Fax: 0120-2560957 MTNL / BSNL (Toll Free) Prefix STD Code P/No.: MFL37725125 The picture shown on Front page is representative model. LG Electronics reserves its right to change, modify or alter design without any prior notice. Global No.1 source : Japan Air Conditioning, Heating and Refrigeration News (JARN), December 2005.